Search Results

Search found 4930 results on 198 pages for 'synergy plus'.

Page 148/198 | < Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >

  • Is a rubber keyboard suitable for heavy use?

    - by Vilx-
    Every keyboard wears out with time, and mine has some age already. The day it fails is coming closer and closer. So I'm slowly starting to look around for a new one. I use the keyboard for gaming and programming, so it gets some pretty solid use. I also tend to eat by the computer, so there's plenty of... uhh... lifeforms down there. Anyway, I was looking at these rubber keyboards. They come pretty cheap (my local computer shop has one for less than $20) and they seem to have some nice properties. They can be easily cleaned, they're quiet, and can be rolled up when needed (plus no worries about spilled drinks). However I'm wondering what their type-ability is. If I can't write on it at a decent speed, the rest of the features don't matter. Not that I'm a fast typer, but being a professional progammer does give a boost to the skill. I couldn't find any reviews on the net so I'm turning to you. Who has used these keyboards and what was your experience? Perhaps there is something else I haven't though of why such a keyboard would not be a good idea?

    Read the article

  • IIS7 - Web Deployment Tool - SetParam/SetParamFile to set http and https bindings + Cert

    - by Andras Zoltan
    Hi, we're currently using the MS Web Deployment Tool to sync a live website and some WebServices from a staging box to two live servers. The staging box hosts the site on any IP on port 17000, whereas the two live servers are load-balanced and have a different IP for each of them. At present, I generate two separate packages for deployment - one for each machine - using the sync operation and specifying a DestinationBinding parameter as follows: msdeploy -verb:sync -source:WebServer,computerName=localhost -dest:package="machinename.zip" -setParam:type="DestinationBinding",scope="SiteName",value="ip_address:port:". (Split across multiple lines to make it easier to read!) I run this twice, with a different target filename and ip address for each of the two machines. When it comes to deployment, I simply do a sync from each package to its respective live site. I know, I know - I should be able to do it by generating one parameterised package and then perhaps using the SetParamFile switch for each of the two Servers - believe me I'd like to, but the documentation on doing this is frankly non-existent. Now I need to configure and deploy both HTTP and HTTPS binding for this site; including also the ssl cert that is to be used. I've added an SSL binding for the site on the staging box - which uses a development cert (which will need to be replaced - or should the staging box be using the live cert?), and now the above command line has the effect of replacing the target IP on both http and https entries. It appears that I cannot specify multiple bindings plus the cert information in the DestinationBinding value in the -setParam above, so anyone know how would I go about doing this? Any help greatly appreciated.

    Read the article

  • Networking - intermittent, slow speeds

    - by jack
    Hi all I'm a novice when it comes to networking. I live in a large two storey building that used to be a school and we have an internet connection with BT (british telecoms provider), the connection speed is 12Mb.. Basically our connection is slow and very intermittent and I was wondering if anybody here could provide some help or ideas. There are about 11 people in the building who could be online at any time. We have a router on the ground floor which is bog standard supplied by BT. To provide Broadband access to the 1st and 2nd floors, we used an old switch that the school left, we have a cable running from the router on the first floor to the switch which connects to a wireless router which is configured as a bridge on the 2nd floor supplying broadband access to the 1st and 2nd floors. Additionally we have 3 computers that are connected via the switch through the ethernet sockets left by the school on the ground floor. The router we use on the 2nd floor came in a pack of 2 and cost about £15 (bought by another person). Sometimes the connection is perfectly fine, i.e. early hours of the morning or when everybody is out, we have rang BT who say that the connection cannot cope with the numbers of people online, plus I'm not sure whether each person is streaming etc. Can anybody offer any advice?

    Read the article

  • How to backup iTunes on Windows to folder/share, i.e. without "Back Up to Disc"? No DVD writer avail

    - by Chris W. Rea
    (Surprised I didn't already find an answer here to this!) I've got a computer on which I'd like to back up the iTunes library – music, movies, apps, everything. We're talking multiple gigabytes. Unfortunately, it seems that iTunes' own built-in "Back Up to Disc" feature (the only backup feature I can find in iTunes) only functions with a CD or DVD writer/burner. The computer in question does not have a DVD burner. While it has a CD burner, attempting to back up to CDs would require dozens of discs plus more time than I'm willing to spend swapping them. So: What is the recommended way to back up an entire iTunes library on a Windows computer, to a non-CD/DVD location such as an external hard drive or a network shared folder? Then, once such a backup has been performed, what is the process for restoring the library – e.g. after the computer has been repaved with a new version of Windows – so that iTunes is resurrected whole and recognizes devices it syncs with? Thank you!

    Read the article

  • Automated software installation for MS Windows?

    - by Duncan Bayne
    I am currently setting up a Windows development environment (the whole Visual Studio 2010 stack plus plugins on top of Windows 7). This has got me wondering whether there's a Windows equivalent to what I do for dev environment setup in Ubuntu. It takes literally hours to get a dev environment set up in Windows, involving a lot of manual intervention. On Ubuntu, I have two shell scripts - one I run as root which configures the system using apt-get (amongst other things), one I run as me which configures my user account. Those scripts live in my private Subversion repository. To set up a dev environment from scratch requires five commands: sudo apt-get install -y subversion svn co http://svn.XXXX.XXX/personal/ cd personal sudo ./ubuntu_setup_root.sh ./ubuntu_setup_user.sh The only human intervention required is to pick a root password for MySQL. So it takes only a few minutes of human attention to go from a vanilla Ubuntu installation to a full development environment with the latest builds of everything, perfectly tailored down to shortcut keys and wallpaper. Is there an equivalent process for Windows? In an ideal world it'd be something trivially scriptable using C# Script or Powershell, which could live in source control & make use of a repository of ISOs downloaded from MSDN ...

    Read the article

  • Will restoring a cPanel account delete irrelevant mysql databases?

    - by user54625
    Long story short: I have many accounts in WHM, many domains. However, most of the MySQL databases for all the sites were created under one user, "admin" (let's say it's admin.com). I recently moved the admin.com account to another web server , and now I need to move it back. I would like to restore this account from a backup made by that web server. However, it only has 3 databases attached to that domain, while the server I'm moving it to has those 3 databases (old DBs that need to be replaced), PLUS all the other databases which are used by other accounts on the server. My question: if I restore the admin.com account, will it delete all the other databases on the account, or will it only replace the 3 DBs it has? I can't take any chances here to delete all those other DBs... If it WOULD delete all those other accounts, how would I go about restoring this account without losing the other data? An easy to way to resolve this situation would be to move the mysql owners to the proper accounts, but alas it doesn't seem that there is a way to do that via WHM.

    Read the article

  • Performance Test and TCP tuning

    - by Mithir
    We are in the process of performance testing an application which receives tcp requests converts them to soap requests (WCF-httpBinding) which other services work on. The server is Windows Server 2008 R2. The TCP requests are received by TcpListener instance (.NET C#). There are 3 http-binded WCF services running on the same server. We have built a performance test client which goal is to simulate multiple concurrent requests(each request has to be different and recognizable by the application). We built a test running 150 requests that run on the same time (by 150 different threads), and we noticed straight away that some requests get the TCP connection slowly, but once they get it, they act fast. A single request writes twice on the same connection- request and an application ack. Although a single request+ack can take about 150ms, the 150 test takes about 7 seconds. The Problem When we try to run this test from 2 different computers we lose requests. some clients requests are getting no connection was made because the target machine actively refused it So I got here and got convinced it was because of the backlog. I changed the TcpListener parameters and did the registry AFD backlog changes written here but it still didn't work, so I inserted all of the TCP tuning suggested plus some netsh commands which were recommended, but still no change, we still get that error. Is there anything else I need to know? Are there any other solutions?

    Read the article

  • Effective backup and archive strategy for database and linked files

    - by busyspin
    I am using Postgres to store a variety of application data for a webapp. Part of the application involves storing and retrieving user uploaded files. I am storing the files in the filesystem with some associated metadata in the database. I am trying to come up with a backup and archive strategy so that I can effectively backup and archive/restore the database and the linked files. Here are the things I want to accomplish. Perform routine backups that can be used for recovery from failures and which include all DB data and the linked files. Ideally, this backup would be done while the app is running. Live backup is certainly possible with a DB but I am not sure how to keep the linked files consistent with the database during the backup process Archive chunks of data as they become "old". These chunks must includes the database data plus any linked files. It should be possible to put the archived data back into production again. It would be ideal if it were easy to determine which ranges of objects were stored in each chunk. Do you have any advice for how to accomplish these goals? If the files were in the database as BLOBS these tasks would be much easier since normal database backup and restore functionality would handle this. I am not sure how to accomplish the same thing when file data is linked to database rows.

    Read the article

  • MacBook Pro (OSX Lion) - shutdown automatically before reaching login screen

    - by mkk
    When I try to lunch my MacBook Pro I can see a progress bar on loading screen. It goes to 1/15 or something like this and then it shut downs - I cannot reach even login screen. It happened to me 2 months ago, I have 'fixed' this by formatting my hard drive and installing OSX (Lion) again. This time I think that situation is a little bit different - I am able to enter single-user mode by pressing cmd + s. I then type /sbin/fsck -yf, I get the error: ** Checking Journaled HFS Plus volume. The volume name is Macintosh HD ** Checking extents overflow file. ** Checking catalog file. Invalid node structure (4, 24704) ** The volume Macintosh HD could not be verified completely. /dev/rdisk0s2 (hfs) EXITED WITH SIGNAL 8 but when I type exit, I can the login screen and I can log in. I tried a lot of things, booting from recovery partition and choosing disk utility to repair the disc, but I get error that it cannot be repaired. I have googled for hours and the only real solution I have found was to buy Disc warrior that might fix the issue. Any other suggestions? Secondary question is what causes this issue? I thought the reason are bad sectors, but Smart Utility haven't found any. I found suggestion that RAM could cause this kind of issue as well, so I downloaded rember and made memory test - all tests passed. Right now I have used my solution of entering single-mode user and then typing exit, however I am not sure how long it will 'work'. Of course I have back-uped what I considered important. Thanks for the help in advance! UPDATE: I guess Smart Utility was not very useful, I mnaged to get input/output error, which I believe is equivalent to bad sector.

    Read the article

  • Convert a cassette tape recording to digital format

    - by Electric Automation
    Has anyone been successful with transferring audio cassette tape recordings to a digital format? I would like to preserve old cassette tape recordings of my grandparents to some digital format: MP3, WAV, etc... The quality of the tapes are mediocre. I think I can handle the quality restoration but getting the audio from tape to digital is my question. Below is a list of the hardware that I can work with: Cassette Deck: I have a Technics stereo cassette deck model RS-B12. It has separate left and right IN and OUT RCA type jacks on the back. In the front it has a headphone phono jack, plus left and right mic input phono jacks. On the computer side: -I have a Windows Vista PC with no additional software other than what came with the machine from Costco. No sound editing software that I can see. There is no sound card on the PC. On the front panel there is a mini-phono mic input jack and there are several different types of in/out mini-phono jacks on the back. In addition, USB and Firewire. I also have access to a new (2009) iMac with a mini-phono input jack for a powered mic or other audio source and GarageBand that has come with the computer. In addition, USB and Firewire. What are my options for getting these cassette recordings into a digital format? Whats the best format? What sort of wires would I need and will I want to utilize the USB or Firewire or can I simply use the audio inputs on the PC (or Mac) to receive the audio stream?

    Read the article

  • Recommendations for hosting large videos

    - by Clinton Blackmore
    I recently created and put a 45-minute, 300 MB video file on my website and told a mailing list about it. Checking my site stats, I see that I've used 20% of my "unlimited" bandwidth for the month. As I want to be able to have several videos like this, clearly, I need to consider other options. The appeal to hosting files as my own site (aside from the supposedly unlimited disk space and bandwidth), is to be able to have control over the format, resolution, and quality of the video(s), as well as to ensure that it is clear that I'm the copyright holder (although the videos will be under a creative commons license). I find that for the screencasts I'm making, having a high resolution (say 3/4 of 1024 * 768) really makes seeing what is going on on the screen easier. It is also always a plus to not have the experience marred by advertisements. One more wrench to throw in is that while the videos are non-commercial, they do promote a club, and it seems that that falls afoul of some terms of services (especially for free services; while free is very nice, I will certainly consider putting up some money.) What recommendations do you have for (fairly) long, high-resolution videos? Should I look in depth at sites like YouTube and Vimeo, should I be considering a filesharing site [I have no qualms with someone downloading the entire video first -- I wouldn't want to watch 45 minutes in my browser!], hosting files with Bittorent (ugh -- I think that'd reduce my audience), or should I be looking into other web hosts (and if so, who?)

    Read the article

  • Does visual source safe take .cvsignore as configuration ?

    - by superuser
    An easy way to tell CVS to ignore these directories is to create a file named .cvsignore (note the leading period) in your top-level source directory Has anyone verified this with vss? Plus,does vss have these similar command lines: * To refresh the state of your source code to that stored in the the source repository, go to your project source directory, and execute cvs update -dP. * When you create a new subdirectory in the source code hierarchy, register it in CVS with a command like cvs add {subdirname}. * When you first create a new source code file, navigate to the directory that contains it, and register the new file with a command like cvs add {filename}. * If you no longer need a particular source code file, navigate to the containing directory and remove the file. Then, deregister it in CVS with a command like cvs remove {filename}. * While you are creating, modifying, and deleting source files, changes are not yet reflected in the server repository. To save your changes in their current state, go to the project source directory and execute cvs commit. You will be asked to write a brief description of the changes you have just completed, which will be stored with the new version of any updated source file.

    Read the article

  • Deploying Office 2010 with MDT 2012 - Multiple Customisaton Files?

    - by Tony Blunt
    I'm in the process of setting up a deployment share for Windows 7 and Office 2010 Pro Plus, using MDT 2012. My question involves the customisation of the Office 2010 install. I've imported Office into MDT and I've successfully created a custom MSP file to tailor the settings to our business. However, I need to have a number of different customisations for different groups of users. For instance, our laptop users need Outlook Anywhere configured whereas desktop users do not. Basically - what's the best way of doing this? Do I have to import Office into MDT more than once, each instance using a different MSP, then have the task sequence select the appropriate instance? It's just that this method seems extremely wasteful so I'm thinking that there's a more intelligent way to do it? Or am I coming at this from the wrong direction? Should I be looking at Group Policy to tweak the Outlook settings in this instance? I'm just aware that there are certain things that OCT can do that group policy cannot, so I would have thought that there must be something I can do in MDT. I'm new to MDT so any pointers will be apprectiated. Thanks in advance.

    Read the article

  • How do hdparm's -S and -B options interact?

    - by user697683
    These two options seem confusing. For example: according to the man page -B 254 "does not permit spin-down". However, testing with -B 254 -S 1 the drive does spin down after 5 seconds. -B Query/set Advanced Power Management feature, if the drive supports it. A low value means aggressive power management and a high value means better performance. Possible settings range from values 1 through 127 (which permit spin-down), and values 128 through 254 (which do not permit spin-down). The highest degree of power management is attained with a setting of 1, and the highest I/O performance with a setting of 254. A value of 255 tells hdparm to disable Advanced Power Management altogether on the drive (not all drives support disabling it, but most do). -S Put the drive into idle (low-power) mode, and also set the standby (spindown) timeout for the drive. This timeout value is used by the drive to determine how long to wait (with no disk activity) before turning off the spindle motor to save power. Under such circumstances, the drive may take as long as 30 seconds to respond to a subsequent disk access, though most drives are much quicker. The encoding of the timeout value is somewhat peculiar. A value of zero means "timeouts are disabled": the device will not automatically enter standby mode. Values from 1 to 240 specify multiples of 5 seconds, yielding timeouts from 5 seconds to 20 minutes. Values from 241 to 251 specify from 1 to 11 units of 30 minutes, yielding timeouts from 30 minutes to 5.5 hours. A value of 252 signifies a timeout of 21 minutes. A value of 253 sets a vendor-defined timeout period between 8 and 12 hours, and the value 254 is reserved. 255 is interpreted as 21 minutes plus 15 seconds. Note that some older drives may have very different interpretations of these values.

    Read the article

  • Xen Windows Guest spawn doesn't spawn a vnc display

    - by Henrik P. Hessel
    I'm using this HVM File to create a new guest kernel = "/usr/lib/xen-3.2-1/boot/hvmloader" builder='hvm' memory = 4096 # Should be at least 2KB per MB of domain memory, plus a few MB per vcpu. shadow_memory = 64 name = "hessel-windows2008" vif = [ 'ip=188.40.xx.xx,mac=00:16:3E:C1:8F:CE' ] acpi = 1 apic = 1 disk = [ 'file:/home/xen/disks/hessel/win2008/win2008.img,hda,w', 'file:/home/xen/isopool/win2008_32.iso,hdc:cdrom,r' ] device_model = '/usr/lib/xen/bin/qemu-dm' #----------------------------------------------------------------------------- # boot on floppy (a), hard disk (c) or CD-ROM (d) # default: hard disk, cd-rom, floppy boot="dc" sdl=0 vnc=1 vncdisplay=1 vnclisten="0.0.0.0" vncconsole=1 vncpasswd='howtoforge' stdvga=0 serial='pty' usbdevice='tablet' The guest is created without an error. But no vnc display is created. Any ideas, how to fix that? prometheus:~# netstat -ant Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:615 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:6010 0.0.0.0:* LISTEN tcp 0 232 188.40.xx.xx:8080 195.36.75.26:54032 ESTABLISHED tcp 0 0 188.40.xx.xx:8080 195.36.75.26:53085 ESTABLISHED tcp6 0 0 :::8080 :::* LISTEN tcp6 0 0 :::53 :::* LISTEN tcp6 0 0 :::22 :::* LISTEN tcp6 0 0 ::1:6010 :::* LISTEN

    Read the article

  • Sendmail : Mail delivery of same domain to internal or external mail server.

    - by Silkograph
    Its bit difficult to explain but very simple problem. We have internal sendmail server and hosted server. Both are set to same domain name. We have mixed mail accounts. For example we have two user in one office. [email protected] is local only [email protected] is internal plus external. Internal means we create user on local linux box where sendmail is set. External means we create user on local and hosted server. [email protected] can send mails to any internal user created on Linux box where sendmail is installed. But he can not send mail to outside domain and no mail can be sent to him as there is no account created on external hosted server. [email protected] can send mails to internal as well as all other domains through sendmail's smart_host feature, which uses hosted server's smtp. [email protected] can get all external emails internally through Fetchmail on linux box. Now we have third user [email protected] who will be always outstation and can use external server only. So I can not create account on local linux box for [email protected] because his mail will get delivered locally only. I don't want to create alias and send his mails to gmail or yahoo's account. I want to send emails to his external account from any internal user. How this can be done? Thanks in advance.

    Read the article

  • Troubleshoot dropped wireless connections

    - by Jack
    I was recently hired in the IT department of a small company (~180 users) and one of the issues that people have been complaining about is having their wi-fi connections drop during meetings. The company is using an HP ProCurve Wireless LAN with 10 APs and a controller unit located in the server room. I don't have any experience troubleshooting WLAN in a multi-AP environment, so I'm trying to at least gather information using free or cheap tools. I did a basic site survey using the free version of Ekahau HeatMapper and discovered the following in one of the conference rooms that has been a problem. The program picked up three access points (plus a bunch of others with much lower signals that were out of range): AP 1: SSID: "Unknown SSID" - Signal strength: -48 dBm - -40 dBm. Channel: 2 AP 2: SSID "CompanyMain" - Signal strength: -35 dBm or greater. Channel: 2. Security: WEP (This is the main SSID for the company's WLAN.) AP 3: SSID: "CompanyGuest" - Signal strength: -40 dBm - -35 dBm. Channel: 2. Security: WPA2 (This SSID is the company's "guest" WLAN, which was setup to allow Internet access, but prevent network access.) Is there anything that you see that is clearly a problem from the above? I'm assuming that the unknown SSID might be a big problem, and that it is an AP from a neighboring office that is causing interference. Does that seem likely? Also, regarding channel, should we try changing the channels of our APs to avoid interference with that unknown SSID? (Since everything seems to be on Channel 2?) Should our APs be on different channels? In other words, should the CompanyMain and CompanyGuest APs be on different channels? Finally, any recommendations for free/cheap tools to help me figure this out, and/or a good methodology to follow? Thanks in advance for any help. Jack

    Read the article

  • How to download Vim script on the command-line?

    - by HaiYuan Zhang
    Whenever I want to install a new Vim script on the Linux server I'm working on, my typical workflow is as the following: surf the plugin's homepage in Vim online using FireXXXX download a right version of the plugin to my laptop by click some highlighted link upload the downloaded plugin from my laptop to Linux server using WinSCP which is really inconvenient. I don't know what is the magic behind this: I mean for the same hyperlink I click it in web browser. I can let you download it but use Wget plus the hyperlink in Linux command-line will end up with nothing but an error indication. Hyperlink in the web browser. Otherwise I can get the link in web browser and then use Wget or some similar tool to actually do the downloding. I try new cool Vim scripts quite ofte , so you can imagine my dismay when I have to repeat the tedious action all the time. What are some tips which can let me download the Vim scripts in a more "professional" way? Post edit: My problem is not find a tool like Wget or cURL. The problem I met is quite specific; to use these tools to download a Vim script. Let's take http://www.vim.org/scripts/script.php?script_id=30 as an example. It's the normal place where one can get the script, at least for me. But I can't find an working URL from this page that can feed to Wget.

    Read the article

  • Cable management techniques

    - by cornjuliox
    How do you manage the giant jungle of cables behind your PC? When you have 2 or more PCs next to each other, you wind up with this giant mess cables that's a pain in the neck to clean especially when both computers are running 24/7 and any fidgeting with the cables is likely to cause data loss and/or angry users. So far I've tried masking tape, cable ties and plain old string but none have been very effective. The masking tape kept the cables in place, but over time they ended up leaving this awful sticky residue on the sides of the cables that just won't come off gets all over your fingers and is horrible horrible horrible. I have nightmares about that stuff. We used cable ties and 'folded' up some of the longer cables so that they weren't any longer than they needed to be, but this meant that the position of some of our devices like the keyboard and the mouse were essentially 'fixed' until we removed the ties. The string didn't work much differently and required that we tie them properly or risk it coming loose. I would switch to a wireless keyboard and mouse, but I don't want to have to deal with the added expense of batteries, even the rechargable ones. Plus I don't want them to die on me at a crucial moment (happened to me once while playing Firearms _<). How do large offices and data centers manage their masses of cable?

    Read the article

  • Cable management techniques

    - by cornjuliox
    How do you manage the giant jungle of cables behind your PC? When you have 2 or more PCs next to each other, you wind up with this giant mess cables that's a pain in the neck to clean especially when both computers are running 24/7 and any fidgeting with the cables is likely to cause data loss and/or angry users. So far I've tried masking tape, cable ties and plain old string but none have been very effective. The masking tape kept the cables in place, but over time they ended up leaving this awful sticky residue on the sides of the cables that just won't come off gets all over your fingers and is horrible horrible horrible. I have nightmares about that stuff. We used cable ties and 'folded' up some of the longer cables so that they weren't any longer than they needed to be, but this meant that the position of some of our devices like the keyboard and the mouse were essentially 'fixed' until we removed the ties. The string didn't work much differently and required that we tie them properly or risk it coming loose. I would switch to a wireless keyboard and mouse, but I don't want to have to deal with the added expense of batteries, even the rechargable ones. Plus I don't want them to die on me at a crucial moment (happened to me once while playing Firearms _<). I know that there are people out there with home/office networks a thousand times more convoluted than mine, so

    Read the article

  • (Zywall USG 300) NAT bypassed when accessing in-house-server From LAN Via domain name

    - by mschr
    My situations is like this; i host a number of websites from within our joint network solution. On the network is basically 3 categories: the known public, registered via mac, given static dhcp lease the anonymous lan connections, given lease from specific dhcp range switches, unix hosts firewall Now, consider following hosts which are of interest 111.111.111.111 (Zywall USG 300 WAN) 192.168.1.1 (ZyWall USG 300 LAN) load balances and bw monitors plus handles NAT 192.168.1.2 (Linux www) serves mydomain1.tld and mydomain2.tld 192.168.123.123 (Random LAN client) accesses mydomain1.tld from LAN 23.234.12.253 (Random External client) accesses mydomain1.tld via WAN DNS A records are setup so that both mydomain1.tld and mydomain2.tld points to 111.111.111.111 - and the Linux www serves the http parts with VirtualHost configurations, setting up the document roots pr ServerName, this is not so interesting though.. NAT rule translates 111.111.111.111:80 to 192.168.1.2:80 (1:1 NAT) Our problem follows; When accessing http://mydomain1.tld from outside (23.234.12.253 example host) the joint network - everything is fine, zywall receives requests via port 80 and maps it to the linux host' httpd. However - once trying to go through the NAT from LAN side (in-house, 192.168.123.123 example host) then one gets filtered in the Zywall port 80 firewall. I know this only because port 443 is open for administration interface and https://mydomain1.tld prompts for zywall login. So my conclusion is, that the LAN that accesses 111.111.111.111 in fact are routed to 192.168.1.1 whilst bypassing the NAT table. I need to know how to setup NAT / Policy Route, so that LAN WAN LAN will function with proper network translations instead of doing the 'quick nameserver lookup' or whatever this might be.

    Read the article

  • How to fix display on external Samsung Syncmaster shifted to the right when connected to Macbook Pro?

    - by joe larson
    Is there something special I need to do to be able to use external LCD displays with my new MacBook Pro? Do I need extra software, or do I possibly need a different cable? I'm attempting to use an external display with my MBP. I've got a "Mini DisplayPort to VGA Female Adapter for Mac", plugged into the thunderbolt port on my MBP, which I understood should be compatible with thunderbolt. I've tried this with three different SyncMaster models: a B2330 (21.5"), a EX2220 (22"), and a third (also 22" ish) which I don't have the model # for -- but all are 1920x1080 resolution; plus an additional HP monitor of similar size and resolution. In all four cases, the MBP recognizes the screen and choses the correct resolution. However, the display is shifted over about 1 inch. This is true no matter if I change screen resolutions also. The controls on the monitor for horizontal position don't help. Also, sometimes (especially if I drag an app over into the second screen), the screen starts skipping left to right and having bands of fuzz. Additionally, the monitor will periodically blink off for a moment, trying to switch from Digital to Analog and back (the Syncmaster shows text on the screen to tell you it's trying to do this). Often when it comes back from one of these blank-outs, it will show OK (no skipping or fuzz) but still shifted right; then after a few seconds it will go wrong again skipping and fuzzy. This photo shows the worst of it. I've added red rectangles to show the physical edge of the screen, and a yellow rectangle to show the empty space on the left of the screen. (Sorry for the awful quality and lighting!) Also, it's worth noting I am on Mac OS X 10.6.7, and yes I have this update 1.4 installed.

    Read the article

  • how do you add an A record for a root domain

    - by nbv4
    this seems really simple, but I can't figure it out. I'm using xname.org since it's free and I own a bunch of domains spread over a few different registrars. The setup I desire is very simple: one A record that points the bare domain name to my server, plus a wildcard CNAME record pointing all subdomains to the same server. So if the user goes to domain.com it will point them to 285.24.435.75, if they go to www.domain, blah.domain.com, or any other sub domain, they'll get sent to 285.24.435.75. All the examples I read on the internet about setting up A records all have the A record set to a subdomain such as www. WWW is deprecated so I want to have noting to do with it. Currently my xname.org zone looks like this: $TTL 86400 ; Default TTL domain.com. IN SOA ns0.xname.org. nbvfour.gmail.com. ( 2010052503 ; serial 10800 ; Refresh period 3600 ; Retry interval 604800 ; Expire time 10800 ; Negative caching TTL ) $ORIGIN domain.com. IN NS ns2.xname.org. IN NS ns0.xname.org. IN NS ns1.xname.org. @ IN A 65.49.73.148 * IN CNAME domain.com The '@' symbol is something that the godaddy domain interface uses to mean "this root domain', but that may have been specefic to that interface and has no meaning here. Before I had a 'www' entry in the A rcords and it worked in the sense that I could ping 'www.domain.com' and it returned a response, but pinging the root domain 'domain.com' returned "no host found".

    Read the article

  • iptables, blocking large numbers of IP Addresses

    - by Twirrim
    I'm looking to block IP addresses in a relatively automated fashion if they look to be 'screen scraping' content from websites that we host. In the past this was achieved by some ingenious perl scripts and OpenBSD's pf. pf is great in that you can provide it nice tables of IP addresses and it will efficiently handle blocking based on them. However for various reasons (before my time) they made the decision to switch to CentOS. iptables doesn't natively provide the ability to block large numbers of addresses (I'm told it wasn't unusual to be blocking 5000+), and I'm a bit cautious over adding that many rules into an iptable. ipt_recent would be awesome for doing this, plus it provides a lot of flexibility for just severely slowing down access, but there is a bug in the CentOS kernel that is stopping me from using it (reported, but awaiting fix). Using ipset would entail compiling a more up-to-date version of iptables than comes with CentOS which whilst I'm perfectly capable of doing it, I'd rather not do from a patching, security and consistency perspective. Other than those two it looks like nfblock is a reasonable alternative. Is anyone aware of other ways of achieving this? Are my concerns about several thousand IP addresses in iptables as individual rules unfounded?

    Read the article

  • Convert a cassette tape recording to digital format

    - by Optimal Solutions
    Has anyone been successful with transferring audio cassette tape recordings to a digital format? I would like to preserve old cassette tape recordings of my grandparents to some digital format: MP3, WAV, etc... The quality of the tapes are mediocre. I think I can handle the quality restoration but getting the audio from tape to digital is my question. Below is a list of the hardware that I can work with: Cassette Deck: I have a Technics stereo cassette deck model RS-B12. It has separate left and right IN and OUT RCA type jacks on the back. In the front it has a headphone phono jack, plus left and right mic input phono jacks. On the computer side: -I have a Windows Vista PC with no additional software other than what came with the machine from Costco. No sound editing software that I can see. There is no sound card on the PC. On the front panel there is a mini-phono mic input jack and there are several different types of in/out mini-phono jacks on the back. In addition, USB and Firewire. I also have access to a new (2009) iMac with a mini-phono input jack for a powered mic or other audio source and GarageBand that has come with the computer. In addition, USB and Firewire. What are my options for getting these cassette recordings into a digital format? Whats the best format? What sort of wires would I need and will I want to utilize the USB or Firewire or can I simply use the audio inputs on the PC (or Mac) to receive the audio stream?

    Read the article

< Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >