Search Results

Search found 11640 results on 466 pages for 'figure'.

Page 149/466 | < Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >

• internal compiler error

  - by hyperboreean

  I am getting this message: internal compiler error: Segmentation fault Please submit a full bug report, with preprocessed source if appropriate. See <file:///usr/share/doc/gcc-4.4/README.Bugs> for instructions. for every compilation that takes longer (ie: linux kernel, kde sources etc.) I've tried other OS (at that moment I was on Fedora 12, now on Debian; was a Suse also) and it didn't work. I've tried replacing my hard disk, since it needed an upgrade either ways - that didn't work either. I assumed that it's the RAM fault - tested them with memtest and it says they are fine. Does anyone know what else I can do in order to figure out where the problem is?

  Read the article

• Apache server-status when running as proxy server

  - by f-z-N

  We are running apache as a proxy server and have tomcat behind apache. We are using server_status module but when we try to access server_status as in https://host.com/server-status it redirects to tomcat and we get 404 error. I am quite new to this, tried going through apache docs but unable to figure out the solution. Fyi.We have ssl enabled Current ssl.conf settings: ProxyRequests Off ProxyPreserveHost On <Proxy http://localhost:8081/*> Order deny,allow Allow from all </Proxy> ProxyPass / http://localhost:8081/ ProxyPassReverse / http://localhost:8081/ ProxyPassReverse / http://myhost:8081/ <Location /server-status> SetHandler server-status Order deny,allow Deny from all Allow from 10.90 </Location>

  Read the article

• dhclient configures /etc/resolv.conf with invalid entry

  - by kubal5003

  I'm trying to figure out why running dhclient on my interface sets /etc/resolv conf to the ip number of my gateway(router). This entry is invalid and each and every time causes inability to resolve any address. I would like to: stop dhclient from overwriting the /etc/resolv.conf or make dhclient write there the valid dns ip from my router More on the environment: I'm using virtual Debian Wheezy as a client system on Windows Seven x64. It is run by Virtualbox with networking mode set to bridged (all packets from debian are injected to my network interface on windows). If I manually configure the /etc/resolv.conf then everything works fine. Doing this on every boot is quite annoying.. PS I know I can write a script to do it for me, but this is not the solution I want. //edit router ip: 192.168.1.100 /etc/resolv.conf AFTER running dhclient eth0: "nameserver 192.168.1.100" what I would like the /etc/resolv.conf to look like: "nameserver 89.202.xxxx" (I don't have to provide the real ip do I? )

  Read the article

• ASP.NET Website not responding

  - by brinthhillerup

  Hello everybody I am setting with my server tech, trying to figure out what is going on here. When I try to access my site through a browser, my site hangs indefinately. It does not respond with anything, not even after 15 minutes! The application pool has been restarted, the website has been restarted. Doesn't helpt at all. It happened during an upload. A backup has been loaded and the problem is still the same It is a very urgent matter, I hope someone can help me! I think we are on a IIS 6 on a Windows 2003 Server. (Remote hosted, with a tech, who has no idea what the issue is as well, so I am trying to find the solution alogn with him). Any suggestions are VERY appriciated.

  Read the article

• HP Server bios boot delay

  - by jjrab

  I'm just going to throw this out there in case anyone else has run accross this... I have an HP DL320 G5p that had the motherboard replaced due to a faulty NIC port. After several calls to HP, two motherboard replacements, PCI riser card replacements, Processor replacement, and power supply replacement, the server takes approx. 10 minutes before it boots into the BIOS. It then boots up with no issues. We've run the HP smart start cd and performed the system tests and everything passed. All firmware has also been upgraded to the latest as well. Has anyone else seen this and found a fix? I am still working with HP, but there seems to be a struggle on their part to figure this out, so I'm curious to know if anyone else has experienced this and found a fix - thanks...

  Read the article

• Remove LCD Stand for Wall Mounting - FSM-270YG

  - by Benjamin Chambers

  Based on Jeff Atwood's post on Coding Horror, I ordered one of these monitors, and I've been absolutely loving it. However, I recently (i.e. today) took the next step in monitor-y goodness and fastened the sucker to an articulated wall mount. Unfortunately, I can't figure out how to remove the stand. The flat portion comes off with a single screw, but the leg it fastens to has no apparent method of removing it. Has anyone figured out a trick for removing these, so they don't just stick out below the screen? Should I remove the screws from the backside of the screen, and look for an internal connection to remove? Or just give up and live with it? (After all, it's a great display, it's floating in the air in front of me, and the stand leg is only a minor annoyance).

  Read the article

• System Reserved Partition has Drive Letter After Applying a WIM Image with ImageX

  - by user1291332

  I have installed Windows Vista on a computer using ImageX from WinPE. I followed the instructions here for partitioning the hard drive, creating a 300 MB system partition and using the rest of the drive for a Windows partition. The install has worked perfectly apart from the fact that the system partition has been assigned the drive letter C: and the Windows has been assigned the drive letter D:. I would like the system drive to have no letter and the Windows partition to have the drive letter C:. I think I have managed to figure out why it is doing this. See my answer below. Can anyone confirm this?

  Read the article

• My php homepage downloads index.php instead of being processed on Gandi.net

  - by alekone

  if I go to the homepage of my website http://www.website.com (on a brand new server) the index.php gets donwloaded instead than processed. I don't have the same problem on other folders. my .htaccess reads: AddHandler php5-script .php what could this be? I suspect it's something with php config / or htaccess, but I'm not able to figure it out. help please! edit: I don't know if this helps: it's a wordpress installation, I have this problem only on the public part of the website, not on the admin (that renders correctly)

  Read the article

• Can't communicate using PuTTY, but can with Termite

  - by SharpHawk

  I'm trying to establish a serial connection to a peripheral from my PC's RS-232 port. Pretty simple stuff, and I've had not trouble doing it with countless peripherals before. And yet when I configure PuTTY to the right baud rate, stop bits, etc. I'll type in "*IDN?", press enter, and the unit won't reply. After going over my settings over and over again, I decided to try another terminal program, Termite. This time it worked like a charm. What puzzles me, and what I'm trying to figure out by posting this question, is why Termite would work when PuTTY did not despite the fact that they both have the same settings. PuTTY: http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Termite: http://www.compuphase.com/software_termite.htm EDIT: I now tried Tera Term as well, and it works. So PuTTY is the odd one out.

  Read the article

• from word to pdf including bookmarks

  - by wanderameise

  hey guys, I created a word file with office 2007 and exported it via jaws pdf. Now I want some bookmarks or any kind of "linking-action" that makes it easier to navigate through the document. My PDF viewer doesnt allow to create bookmarks in the free version so I guess I need to handle this via word! maybe using a table of content? anything that is recognized by pdf! thanks in advance edit: I realised it with using a table of centent.it works fine but that wasnt the solution if been looking for.I like to have some bookmarks but my pdf creator doesnt take over the one I created in word. need to figure out how this could works

  Read the article

• Strange strace and setuid behaviour: permission denied under strace, but not running normally.

  - by Autopulated

  This is related to this question. I have a script (fix-permissions.sh) that fixes some file permissions: #! /bin/bash sudo chown -R person:group /path/ sudo chmod -R g+rw /path/ And a small c program to run this, which is setuided: #include "sys/types.h" #include "unistd.h" int main(){ setuid(geteuid()); return system("/path/fix-permissions.sh"); } Directory: -rwsr-xr-x 1 root root 7228 Feb 19 17:33 fix-permissions -rwx--x--x 1 root root 112 Feb 19 13:38 fix-permissions.sh If I do this, everything seems fine, and the permissions do get correctly fixed: james $ sudo su someone-else someone-else $ ./fix-permissions but if I use strace, I get: someone-else $ strace ./fix-permissions /bin/bash: /path/fix-permissions.sh: Permission denied It's interesting to note that I get the same permission denied error with an identical setup (permissions, c program), but a different script, even when not using strace. Is this some kind of heureustic magic behaviour in setuid that I'm uncovering? How should I figure out what's going on? System is Ubuntu 10.04.2 LTS, Linux 2.6.32.26-kvm-i386-20101122 #1 SMP

  Read the article

• How do I access site.project.rails (running on host) from VMWare fusion?

  - by Johnny Mnemonic

  I have a rails app setup and running on my snow leopard MacBook - the app is being served by Passenger. As part of the setup they had me add entries for 127.0.0.1 site.project.rails in my hosts file so I could reach the site from site.project.rails I can't for the life of me figure out how to get the app show up in VMWare. I have XP setup and browse to http://site.project.rails and I can't get it to show up. I setup a basic rails app, being served at localhost:3000 by webrick, I can get that to load by visiting my hosts ip (http://192.168.1.1:3000/). I added the same hosts I added on my Mac to Windows. I also Bridged the network under settings for the VM. What am I missing?

  Read the article

• Windows Firewall: How to allow traffic on port 8080?

  - by Chadworthington

  I am trying to configure team Foundation Server so that 1) it is accessible from within my Home Network 2) and then make the Web site access accessible via the Internet I have a problem with point 1: When I access http://192.168.1.106:8080/tfs/web/ locally from 192.168.1.106, it works. When I access the same web site from another PC in my home network, the abive URL works only if I turn of the Firewall on 192.168.1.106. Can someone please tell me specifically how to allow traffic on port 8080 without turning off Windows Firewall? It seems that the exceptions that I specify are intended for listing programs on the box that need to communicate out. Is IIS the program that I need to make the exception? How do I specify that port 8080 traffic should be allowed for web site traffic on this port? I hope to have success with pt. 2 later but I figure (1) should be done first. I expect issues.

  Read the article

• How to find the /dev name of my USB device

  - by mustafa

  I am running Ubuntu 11 on VmWare on Windows XP. I want to format an SD card in Ubuntu. But, I can't figure out which /dev/xxx device the SD card is. I plug the card into the built-in socket of my laptop. I "safely remove" the device in Windows. Then, I "connect" the PCMCIA reader in VmWare. Now, I was supposing to see a new device like /dev/sdx. But, it doesn't appear :( How can I find what the name of my USB device's name and mount it? /var/log/message is empty. Here is the output of dmesg: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd And, here is the last lines of /var/log/syslog: Oct 31 18:51:21 ubuntu kernel: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd Oct 31 18:51:21 ubuntu mtp-probe: checking bus 2, device 12: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-1" Oct 31 18:51:21 ubuntu mtp-probe: bus: 2, device: 12 was not an MTP device

  Read the article

• What kind of server hardware is roughly necessary to serve website to 10k users?

  - by jcmoney

  I've been looking at VPS's and the specs they offer for entry level setups seems somewhat surprising to me. I'm am new to this topic but many of VPS offer less than 512MB of memory and my laptop has 4GB of memory so I am curious what does it actually take in terms of hardware to serve say 10k users (say 5k daily active users)? I figure a large number of factors can probably sway this a lot but just for benchmarking, say the site is a social networking site written in php using mysql + apache that's not really doing anything unusual like serving lots of media. So essentially a very basic Facebook minus the absurd number of photos and videos. What about 100k users (50k daily active)? 1 million (500k daily active)? Thanks in advance.

  Read the article

• WSUS works, but checkhealth logs events 13042 12002 12012 12032 12022 12042 12052

  - by jobu1324

  Our WSUS server stopped working until the patch related to .NET 4.0 was installed, at which point clients started downloading and updating again. However, the WSUS mmc console occasionally disconnects when performing various tasks, such as running automatic approval rules; also wsusutil checkhealth creates the following events: 13042: Self-update is not working. 12002: The Reporting Web Service is not working. 12012: The API Remoting Web Service is not working. 12032: The Server Synchronization Web Service is not working. 12022: The Client Web Service is not working. 12042: The SimpleAuth Web Service is not working. 12052: The DSS Authentication Web Service is not working. Apparently there are many possible causes for these events. I'm looking for a way to figure out what is wrong, so that I can fix it.

  Read the article

• What is Peformance Monitor telling me when my page faults / second are high?

  - by David Robison

  I have a Windows 7 x64 computer that is having performance issues. After some investigation, I have discovered that the page faults / second on it, as reported by Performance Monitor, are really high. Everything else seems to be normal. Resource Monitor reports no hard faults and lots of available memory. Is this a potential cause for problems, or is it a red herring? If it is something that could be causing problems, what should I do next to figure out what is causing it? Here is a screen shot of the Performance Monitor. Notice that the average page faults / second is 75,887. On another computer that does not have problems, this number is closer to 3,000. Here is a screen shot of the Resource Monitor, sorted by hard faults / second, which is currently 0 for all processes.

  Read the article

• Return cell reference as result of if statement with vlookups.

  - by EMJ

  I have two sets of data in excel. One contains a set of data which represents the initial step of a process. The other set of data represents the additional steps which take place after the first step is completed. Each of the data records in the "additional step data" has an id in a column. I need to find the identifying codes of the "additional step data" which correspond with the initial step data records. The problem is that I have to match the data in 4 columns between the two data sets and return the id of the "additional step data". I started by doing a combination of an if and vlookup functions, but I got stuck when I tried to figure out how to get the if statement to reference the id of the matching "additional step data". Basically I am trying to avoid having to search by manually filtering between two sets of data and finding corresponding records. Does anyone have any idea about how to do this?

  Read the article

• Connection to mysql server in SYN_SENT

  - by Sunil

  We are facing a strange problem from last few days between our application server and database server(Mysql): connection to database server from application server hangs in SYN_SENT state and after that we are not able to make any connection to database server on mysql port(3306). When we checked the netstat output on database server its in SYN_RECV state. What I can figure out is mysql server is receiving the SYN request and responding also and its not reaching to the client hence SYN_RECV at server side and SYN_SENT at client side. I think SYN_SENT state should go after some time and because of this other db connection attempts to same server should not hang. Does anybody have any idea how can we resolve this issue? Out setup details : Application server: RHEL 5.4, kernel-release = 2.6.18-164.el5, x86_64 Database server: Mysql Version : 5.1.49 RHEL 5.4, kernel-release = 2.6.18-164.el5, x86_64

  Read the article

• Is there a way to add a custom favicon to an App Tab?

  - by Iszi

  Since the release of Firefox "5", I've come to really love the new "App Tabs" feature. However, I've now realized that several internal websites at work do not have favicons. So, when I make an App Tab out of these sites, there's only a "blank page" icon in the tab. Perhaps I wouldn't mind so much if there was only one, but there's at least two or three of these. So, it's just a bit annoying to have to mouse-over the App Tabs to figure out which is what. I've tried using Favicon Picker 2 to change the bookmark icons, but it only does exactly that - changes the icon in the bookmarks folder. It doesn't change the favicon that's displayed next to the URL in the Address Bar, or the one next to the page title in tabs - the latter being that which is used for the App Tab icon. So, is there a plugin or other client-side (and preferably "Joe User" friendly) method to assign an icon to a web page or domain, that will be used in the tab bar?

  Read the article

• Docbook: Centralized glossary, where each document includes only terms which appear in it?

  - by DanM

  Trying to figure out if this (or something similar) is possible. I'm working with a collection of technical documents, all written in DocBook. The documents each contain many acronyms, technical terms and other jargon, so we need to include a glossary with each of them. The ideal situation would be this: I have a central glossary.xml file which contains a glossentry item (or similar) for each such term; then, each of the documents uses that glossary file, but only prints out the terms which appear IN that document. So, each document has its own glossary printed at the end, but the actual glossary entries are stored centrally. Is that doable?

  Read the article

• Is my disk hot or not?

  - by adriangrigore

  I am trying to figure out the temperature of my dedicated server's harddisk. For this purpose, I've downloaded HDTune to monitor the S.M.A.R.T. Status. The problem is that the current temperature for "C2 Temperature" is 73 degrees celsius, but the little thermometer on top of the window shows 27 degrees celsius. See this screenshot: http://screencast.com/t/OGJhZGIxND Another monitoring software (Anfibia Reactor) shows similar behavior: Disk temperature is around 30 degrees, but it says that the disk is too hot. So, is my disk hot or not? Since this is a dedicated server, I can't just open the case and put a thumb on it.

  Read the article

• Enable Remote Desktop File Transfer

  - by Eric J.

  Most of the servers I RDP to support cut-and-paste file transfer (from my Win7 64 machine). One does not, and I can't figure out what configuration step is missing. I followed the steps outlined here: http://support.microsoft.com/kb/313292 but do not see the local file system on the remote server (or vice versa for that matter), and I cannot cut and paste files from the local to the remote system. If I try to cut and paste from the remote system to the local one, I get the error Cannot copy FILENAME: Windows cannot find '%1!ls!'. Check the spelling and try again, or try searching for the item by clicking the Start button and then clicking Search. The remote server is Windows Server 2003 Standard Edition.

  Read the article

• Why aren't Heroku syslog drains logging to rsyslogd?

  - by Benjamin Oakes

  I'm having a problem using syslog drains as described in https://devcenter.heroku.com/articles/logging. To summarize, I have an Ubuntu 10.04 instance on EC2 that is running rsyslogd. I've also set up the security groups as they describe, and added a syslog drain using a command like heroku drains:add syslog://host1.example.com:514. I can send messages from the Heroku console to my rsyslogd instance via nc. I see them appear in the log file, so I know there isn't a firewall/security group issue.  However, Heroku does not seem to be forwarding log messages to the server that heroku drains lists. I would expect to see HTTP requests, Rails messages, etc. Is there something else I can try to figure this out? I'm new to rsyslogd, so I could easily be missing something.

  Read the article

• postfix header_checks using regexp proper setup

  - by Philip Rhee

  I just can't seem to figure out why header_checks are not being evaluated. I'm on Ubuntu 12.04, postfix 2.7, dovecote, spamassasin, clamav, amavis. I add following line to /etc/postfix/main.cf : header_checks = regexp:/etc/postfix/header_checks And here is header_checks : /From: .*/ REPLACE From: [email protected] To test out regexp : #postmap -q "From: <werwe>" regexp:/etc/postfix/header_checks which evaluates correctly and give me return output of : REPLACE From: [email protected] However, when I try to send email from commandline or from php webpage, postfix will not replace the From header. I'm stumped.

  Read the article

< Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >