Search Results

Search found 577 results on 24 pages for 'dmesg'.

Page 15/24 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

• E160 ubuntu 12.04 can't detect the modem

  - by Matt

  i've got problem with e160 on ubuntu 12.04. I'cant configure network manager and connect because NM can't see the e160. I;ve tried lot of solutions with no result. ateusz@mateusz-Aspire-5738:~$ sudo usb_modeswitch -v 0x12d1 -p 0x1003 -H [sudo] password for mateusz: aLooking for default devices ... found matching product ID adding device Found device in default mode, class or configuration (1) Accessing device 002 on bus 001 ... Getting the current device configuration ... OK, got current device configuration (1) Using first interface: 0x00 Using endpoints 0x01 (out) and 0x82 (in) Not a storage device, skipping SCSI inquiry USB description data (for identification) ------------------------- Manufacturer: HUAWEI Technology Product: HUAWEI Mobile Serial No.: not provided ------------------------- Sending Huawei control message ... OK, Huawei control message sent - Run lsusb to note any changes. Bye. Dmesg [ 521.480062] usb 1-4: reset high-speed USB device number 4 using ehci_hcd [ 521.617792] option 1-4:1.1: GSM modem (1-port) converter detected [ 521.617945] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB0 [ 521.618062] option 1-4:1.0: GSM modem (1-port) converter detected [ 521.618232] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB1 [ 530.840276] option: option_instat_callback: error -108 [ 530.840455] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 530.840484] option 1-4:1.0: device disconnected [ 537.680378] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 [ 537.680398] option 1-4:1.1: device disconnected [ 537.792088] usb 1-4: reset high-speed USB device number 4 using ehci_hcd [ 537.929549] option 1-4:1.1: GSM modem (1-port) converter detected [ 537.929702] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB0 [ 537.929818] option 1-4:1.0: GSM modem (1-port) converter detected [ 537.929993] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB1 [ 547.224294] option: option_instat_callback: error -108 [ 547.224470] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 547.224511] option 1-4:1.0: device disconnected [ 556.988066] tty_ldisc_hangup: waiting (usb-storage) for ttyUSB0 took too long, but we keep waiting... [ 558.990663] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 [ 558.990698] option 1-4:1.1: device disconnected [ 559.100068] usb 1-4: reset high-speed USB device number 4 using ehci_hcd [ 559.241293] option 1-4:1.1: GSM modem (1-port) converter detected [ 559.241446] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB0 [ 559.241565] option 1-4:1.0: GSM modem (1-port) converter detected [ 559.241739] usb 1-4: GSM modem (1-port) converter now attached to ttyUSB1 [ 568.728283] option: option_instat_callback: error -108 [ 568.728466] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 568.728496] option 1-4:1.0: device disconnected lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 064e:a103 Suyin Corp. Acer/HP Integrated Webcam [CN0314] Bus 005 Device 002: ID 09da:c20a A4 Tech Co., Ltd Bus 001 Device 002: ID 12d1:1003 Huawei Technologies Co., Ltd. E220 HSDPA Modem / E230/E270/E870 HSDPA/HSUPA Modem

  Read the article

• Ubuntu boots to terminal on start up

  - by Jules

  For a long time I've been unable to get updates due to a "repositories not found" error. Yesterday someone fixed this for me but after installing 94 days worth of updates my system wanted to restart. It looks like it is booting normally but then it opens a terminal and asks for my login and password. I had tried Ctrl+ Alt +F7 and startx to no avail. Here is everything that appears on screen when I turn the computer on. Ubuntu 10.04.4 LTS box-o-doom tty1 box-o-doom login:julian password: last login: Sun Jul 8 10:28:02 BST tty1 Linux box-o-doom 2.6.32-41-generic-pae #91-Ubuntu SMP Wed Jun 13 12:00:09 UTC 20 12 i686 GNU/Linux Ubuntu 10.04.4 LTS Welcome to Ubuntu! *Documentation: http://help.ubuntu.com julian@box-o-doom:~$_ i then tried dmesg which produced hundreds of lines all very similar to the first line reproduced here [ 9.453119] type=1505 audit1341742405.022:10): operation="profile_replace" pid=743 name="/usr/lib/connman/scripts/dhclient-script" follwed by this at the end [ 9.475880] alloc irq_desc for 27 on node-1 [ 9.475883] alloc kstat_irqs on node-1 [ 9.475890]forcedeth 0000:00:07.0: irq27 for MSI/MSI-X [ 9.760031] hda_code:ALC662 rev1: BIOS auto-probing. [ 10.048095] input:HDA Digital PCBeep as /devices/pci 0000:00:05.o/inp ut/input6 [ 10.862278] ppdev: user-space parallel port driver [ 20.268018] eth0: no IPv6 routers present julian@box-o-doom:~$_ results of startx lots of text scrolls off the screen and i have no way of reading it. but everything i can see is reproduced below current version of pixman: 0.16.4 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version Markers: (--) probed, (**) from config file, (==) defult setting, (++) from command line, (!!) notice, (II) informational. (WW) Warning, (EE) error, (NI) not implemented, (??) unknown. (==) log file: "/var/log/Xorg.0.log", Time: SUn Jul 8 12:02:23 2012 (==) using config file: "/etc/X11/xorg.conf" (==)using config directory: "/usr/lib/X11/xorg.conf.d" FATAL: Module nvidia not found. (EE) NVIDIA: Failed to load the NVIDIA kernal module please check your (EE) NVIDIA: systems kernal log for aditional error messages. (EE) Failed to load module "nvidia" (module specific error, 0) (EE) No drivers available. Fatal server error: no screens found please consult the X.org foundation support at http://wiki.x.org for help please also check the log files at "/var/log/X.org.0.log" for aditional informati on ddxSigGiveUp: Closing log giving up xinit: No such file or directory (errno 2): unable to connect to X server xinit: No suck process (errno 3): server error julian@box-o-doom:~$_

  Read the article

• Lubuntu Desktop messed up for logged in user, but not for guest

  - by RPi Awesomeness

  I recently upgraded my laptop from Lubuntu 12.04 to 14.04.1 and the upgrade process seemed to go fine. However, when I went to login as my normal user, I encountered an issue. The background loaded up, but none of LXDE or LXPanel showed up, leaving me with an empty desktop and nothing else except two errors. I thought that this was weird, so I just figured something had been messed up and would be fixed by a reboot. But it wasn't. I then tried logging in as guest, and it's just fine. I checked the ~/.xsession-errors file (for my main user, not guest, did it via TTY1) and this is what I got: Script for ibus started at run_im. Script for auto started at run_im. Script for default started at run_im. init: Unable to register as subreaper: Invalid argument init: lxsession main process (1649) killed by TERM signal init: Disconnected from notified D-Bus bus init: job dbus failed to stop init: job upstart-dbus-session-bridge failed to stop init: job upstart-dbus-system-bridge failed to stop init: job upstart-file-bridge failed to stop I also read the sometimes removing the ~/.Xauthority file can help, if the ownership is messed up. ls -l /home/MYUSER/.Xauthority tells me -rw------- 1 MYUSER MYUSER 60 Aug 16 09:57 /home/MYUSER/.Xauthority. Should that be root or something else, or should I try deleting that and ~/.profile. Here's what ~/.profile looks like: # ~/.profile: executed by the command interpreter for login shells. # This file is not read by bash(1), if ~/.bash_profile or ~/.bash_login # exists. # see /usr/share/doc/bash/examples/startup-files for examples. # the files are located in the bash-doc package. # the default umask is set in /etc/profile; for setting the umask # for ssh logins, install and configure the libpam-umask package. #umask 022 # if running bash if [ -n "$BASH_VERSION" ]; then # include .bashrc if it exists if [ -f "$HOME/.bashrc" ]; then . "$HOME/.bashrc" fi fi # set PATH so it includes user's private bin if it exists if [ -d "$HOME/bin" ] ; then PATH="$HOME/bin:$PATH" fi Should I post the output of dmesg? I'll try and get a screenshot, but does anyone have any idea what could be causing the desktop (LXDE/LXPanel) not to display? EDIT I attempted removing the ~/.XAuthority file, but that didn't seem to do anything.

  Read the article

• Send raw data to USB parallel port after upgrading to 11.10

  - by zaphod

  I have a laser cutter connected via a generic USB to parallel adapter. The laser cutter speaks HPGL, as it happens, but since this is a laser cutter and not a plotter, I usually want to generate the HPGL myself, since I care about the ordering, speed, and direction of cuts and so on. In previous versions of Ubuntu, I was able to print to the cutter by copying an HPGL file directly to the corresponding USB "lp" device. For example: cp foo.plt /dev/usblp1 Well, I just upgraded to Ubuntu 11.10 oneiric, and I can't find any "lp" devices in /dev anymore. D'oh! What's the preferred way to send raw data to a parallel port in Ubuntu? I've tried System Settings Printing + Add, hoping that I might be able to associate my device with some kind of "raw printer" driver and print to it with a command like lp -d LaserCutter foo.plt But my USB to parallel adapter doesn't seem to show up in the list. What I do see are my HP Color LaserJet, two USB-to-serial adapters, "Enter URI", and "Network Printer". Meanwhile, over in /dev, I do see /dev/ttyUSB0 and /dev/ttyUSB1 devices for the 2 USB-to-serial adapters. I don't see anything obvious corresponding to the HP printer (which was /dev/usblp0 prior to the upgrade), except for generic USB stuff. For example, sudo find /dev | grep lp produces no output. I do seem to be able to print to the HP printer just fine, though. The printer setup GUI gives it a device URI starting with "hp:" which isn't much help for the parallel adapter. The CUPS administrator's guide makes it sound like I might need to feed it a device URI of the form parallel:/dev/SOMETHING, but of course if I had a /dev/SOMETHING I'd probably just go on writing to it directly. Here's what dmesg says after I disconnect and reconnect the device from the USB port: [ 924.722906] usb 1-1.1.4: USB disconnect, device number 7 [ 959.993002] usb 1-1.1.4: new full speed USB device number 8 using ehci_hcd And here's how it shows up in lsusb -v: Bus 001 Device 008: ID 1a86:7584 QinHeng Electronics CH340S Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x1a86 QinHeng Electronics idProduct 0x7584 CH340S bcdDevice 2.52 iManufacturer 0 iProduct 2 USB2.0-Print iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 96mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 7 Printer bInterfaceSubClass 1 Printer bInterfaceProtocol 2 Bidirectional iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Device Status: 0x0000 (Bus Powered)

  Read the article

• Audio Stutters at gdm

  - by Allan

  Ok I have a problem every 2 times out of 3 I login (I cant be specific it fairly random) I get a Stuttering GDM warning (not the login sound just the Bell sound to wake you up) the only way to stop it is to login I have a Fujitsu Siemens Amilo 1718 with a 2gig of memory (only hardware mod) using 10.10 Maverick and I have disabled KMS as my system was freezing as per the release notes. The only time this has happened before on the same machine was when I gave Kubuntu a try when 10.04 came out then it happened at the login screen and at random times while listening to music in any program. By the way audio is fine as is almost everything else once I have logged in. I would like an answer to this as I am an advocate of Ubuntu and its kind of embarrassing when the first thing that happens is *bing*. as requested Daniel alsa-info Pulse verbose log Not sure how useful the pulse log will be as I cant replicate the bug with a terminal open but I wouldnt be asking the question if I knew the answer so..... Edit 24/12/2010 ......been living on cocktail sausages and pickled onions for five days now made a make shift splint with cocktail sticks..... oops so updated the alsa drivers but I still get the same message in the dmesg No response from codec, disabling MSI: last cmd=0x10a90000 googleing it brings up a forum post from some other distro with a green logo the only common denominator seems to be graphics ie ATI Radeon XPRESS 200M which is why I have had to turn of kms as the chip is so old that small mice try to eat the "kernel" ;) funnily enough following the bug link at the end of the post, I found a comment about "Ubuntu Black Magic" so mabey I am coming at this from the wrong angle...... Bad Joo Joo any one. I will try the second part of Daniels Fix and Update with the result. The final Edit: (Plays air guitar) In the end neither of these solved the problem as such However I have given Roland a tick for reminding me of the solution and I gave Daniel the Bounty for the effort in trying to solve the problem. The answer for future readers was the enable the correct HD Audio Model I found the answer back when using Karmic Koala 9.10 in this forum post Amilo Li1718 Skype - Can't get it working... the model is options snd-hda-intel model=3stack position_fix=1 enable=yes which can be added to the end of alsa-base.conf thanks all for helping and hope anyone with a similar problem will find the answer here.

  Read the article

• Wifi disabled for Intel Centrino Wireless-N 1000 Intel in 12.04

  - by new_bie

  Laptop model - HP- dm4 - 2070. I had faced the same problem for wireless being disabled in case of 11.10. It had to do with the new kernel. I thought with 12.04 this problem will be handled but the problem persists. Is there no way to get the wireless working except for the way mentioned in the following link ?? Wifi for Centrino Wireless-N 1000 Intel Corporation (HP pavillion dm4 - 2070us) is not working Output for sudo lshw -class network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress cap_list configuration: latency=0 resources: memory:c2500000-c2501fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: c0 serial: 2c:41:38:07:f3:e3 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.116 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:c1400000-c143ffff ioport:2000(size=128) Output for dmesg | grep iwl [ 14.742886] iwlwifi 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 14.742897] iwlwifi 0000:01:00.0: setting latency timer to 64 [ 14.743013] iwlwifi 0000:01:00.0: pci_resource_len = 0x00002000 [ 14.743016] iwlwifi 0000:01:00.0: pci_resource_base = ffffc90000c78000 [ 14.743018] iwlwifi 0000:01:00.0: HW Revision ID = 0x0 [ 14.743119] iwlwifi 0000:01:00.0: irq 42 for MSI/MSI-X [ 14.743161] iwlwifi 0000:01:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 14.743229] iwlwifi 0000:01:00.0: L1 Enabled; Disabling L0S [ 14.765147] iwlwifi 0000:01:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 14.765151] iwlwifi 0000:01:00.0: Device SKU: 0X50 [ 14.765154] iwlwifi 0000:01:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 14.765907] iwlwifi 0000:01:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 14.912840] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-5.ucode' failed. [ 14.914254] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-4.ucode' failed. [ 14.915718] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-3.ucode' failed. [ 14.916986] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-2.ucode' failed. [ 14.919391] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-1.ucode' failed. [ 14.919445] iwlwifi 0000:01:00.0: no suitable firmware found! [ 14.919783] iwlwifi 0000:01:00.0: PCI INT A disabled [ 2868.960807] Modules linked in: snd_hda_codec_hdmi snd_hda_codec_idt rfcomm bnep bluetooth parport_pc ppdev binfmt_misc hid_logitech_dj usbhid hid joydev snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq hp_wmi sparse_keymap hp_accel lis3lv02d input_polldev snd_timer snd_seq_device wmi iwlwifi snd mac80211 i915 cfg80211 rts_pstor(C) drm_kms_helper drm uvcvideo videodev psmouse soundcore mei(C) v4l2_compat_ioctl32 mac_hid serio_raw snd_page_alloc i2c_algo_bit video lp parport atl1c

  Read the article

• "sr0" I/O read boot error in Xubuntu 12.10

  - by Entropicurity

  Just recently upgraded Xubuntu 12.10 after having installed 12.04 originally. Ever since that happened, any time I inserted a disk into my DVD/CD reader/writer I would end up getting a number of error messages from my DVD player/Audio player softer, typically with any of them either crashing or returning a GStreamer backend error. So doing some research I tried to mount it manually, and it typically returned the error messages you'll see below: (using the dmesg | grep "sr0" command) [17545.435584] end_request: I/O error, dev sr0, sector 0 [17545.492968] sr 3:0:0:0: >[sr0] [17545.492981] sr 3:0:0:0: >[sr0] [17545.492992] sr 3:0:0:0: >[sr0] [17545.493003] sr 3:0:0:0: >[sr0] CDB: [17545.493020] end_request: I/O error, dev sr0, sector 0 [17545.493058] EXT3-fs (sr0): error: unable to read superblock [17545.553224] sr 3:0:0:0: >[sr0] [17545.553237] sr 3:0:0:0: >[sr0] [17545.553247] sr 3:0:0:0: >[sr0] [17545.553258] sr 3:0:0:0: >[sr0] CDB: [17545.553275] end_request: I/O error, dev sr0, sector 0 [17545.553312] EXT4-fs (sr0): unable to read superblock [17545.611482] sr 3:0:0:0: >[sr0] [17545.611494] sr 3:0:0:0: >[sr0] [17545.611504] sr 3:0:0:0: >[sr0] [17545.611514] sr 3:0:0:0: >[sr0] CDB: [17545.611531] end_request: I/O error, dev sr0, sector 0 [17545.611568] FAT-fs (sr0): unable to read boot sector When I grepped this, the number of error messages just seemed to spill all over the screen, and typically all revolve around the I/O error. I then went into VLC and tried to run the stuff through there, but for some reason it won't read with the default devices. Instead I have to manually input sr0 into each of the /dev/ references and it will play just fine, until I exit out of the program, at which point I have to re-input everything. I have already installed all the media dependencies, both open source and restricted, through the software center. I just found this strange, as out of the box 12.04 there wasn't any problem what so ever. At this point, it could be that all my audio CD's are not in a format that is familiar with the OS (I've read in some places that EXTF4 has issues with this) but I don't see how that could be a problem when the above error messages even tested to see if it is EXT3 as well? I've tried my best to troubleshoot this up till now using existing topics, but it seems that this is a regular problem with a multitude of varying factors that incorporate into it, including but not limited to read/write problems with the format of the CD and right protection. Is there something integral that I am missing?

  Read the article

• Bluetooth firmware problem in Ubuntu 13.04

  - by chanzerre

  I have a [Dell Inspiron][1] 15R 5520 laptop. Bluetooth is not working at all. rfkill list all gives 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no dmesg|grep -i bluetooth gives [ 13.644428] Bluetooth: Core ver 2.16 [ 13.644445] Bluetooth: HCI device and connection manager initialized [ 13.644453] Bluetooth: HCI socket layer initialized [ 13.644455] Bluetooth: L2CAP socket layer initialized [ 13.644461] Bluetooth: SCO socket layer initialized [ 15.861363] Bluetooth: hci0 command 0x1003 tx timeout [ 15.903443] Bluetooth: can't load firmware, may not work correctly [ 17.332535] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 17.332538] Bluetooth: BNEP filters: protocol multicast [ 17.332544] Bluetooth: BNEP socket layer initialized [ 17.393768] Bluetooth: RFCOMM TTY layer initialized [ 17.393781] Bluetooth: RFCOMM socket layer initialized [ 17.393783] Bluetooth: RFCOMM ver 1.11 hciconfig gives hci0: Type: BR/EDR Bus: USB BD Address: E0:06:E6:D5:DB:46 ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING PSCAN ISCAN RX bytes:687 acl:0 sco:0 events:56 errors:0 TX bytes:2024 acl:0 sco:0 commands:52 errors:0 I have visited the site http://wireless.kernel.org/en/users/Drivers/b43 and according to it lspci -vnn -d 14e4: gives 08:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01) Subsystem: Dell Wireless 1704 802.11n + BT 4.0 [1028:0016] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at c1500000 (64-bit, non-prefetchable) [size=32K] Capabilities: <access denied> Kernel driver in use: wl So I got my PCI-ID as 14e4:4365 which it says is not supported. The alternative is wl. What should I do? My Wi-Fi is working normally without any problems, but Bluetooth is not working. sudo dpkg -i wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb gives following error (Reading database ... 208543 files and directories currently installed.) Unpacking wireless-bcm43142-dkms (from wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb) ... Setting up wireless-bcm43142-dkms (6.20.55.19-1) ... Loading new wireless-bcm43142-6.20.55.19 DKMS files... Building only for 3.8.0-23-generic Building initial module for 3.8.0-23-generic Traceback (most recent call last): File "/usr/share/apport/package-hooks/dkms_packages.py", line 22, in <module> import apport ImportError: No module named apport Error! Bad return status for module build on kernel: 3.8.0-23-generic (x86_64) Consult /var/lib/dkms/wireless-bcm43142/6.20.55.19/build/make.log for more information.

  Read the article

• NVidia with Optimus conflicting in Ubuntu 12.04

  - by Humannoise

  i have recently installed Ubuntu 12.04 in a Intel Ivy Bridge with integrated graphics and NVidia GPU with Optimus tech, however i cant manage it to work properly. I have already passed by the solution of bumblebee project, however iam got the following message when try to run anything with nvidia card( e.g. with optirun firefox): [ERROR]The Bumblebee daemon has not been started yet or the socket path /var/run/bumblebee.socket was incorrect. [ERROR]Could not connect to bumblebee daemon - is it running? Since the nvidia card is not working properly, some softwares like Scilab, that make use of X11 system for graphic handling and plotting, wont work too. my bios has no option concerning graphics card and the log of daemon returned: Jul 5 16:10:51 humannoise-W251ESQ-W270ESQ bumblebeed[980]: Module 'nvidia' is not found. Jul 5 16:10:51 humannoise-W251ESQ-W270ESQ kernel: [ 17.943272] init: bumblebeed main process (980) terminated with status 1 Jul 5 16:10:51 humannoise-W251ESQ-W270ESQ kernel: [ 17.943288] init: bumblebeed main process ended, respawning Jul 5 16:10:51 humannoise-W251ESQ-W270ESQ bumblebeed[1026]: Module 'nvidia' is not found. The lspci -nn | grep '\[030[02]\]:' returned: 00:02.0 VGA compatible controller [0300]: Intel Corporation Ivy Bridge Graphics Controller [8086:0166] (rev 09) 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation Device [10de:0de9] (rev a1) Ok, for the command dpkg -l | grep '^ii' | grep nvidia i got : ii bumblebee-nvidia 3.0-2~preciseppa1 nVidia Optimus support using the proprietary NVIDIA driver ii nvidia-current 302.17-0ubuntu1~precise~xup1 NVIDIA binary Xorg driver, kernel module and VDPAU library ii nvidia-current-updates 295.49-0ubuntu0.1 NVIDIA binary Xorg driver, kernel module and VDPAU library ii nvidia-settings 302.17-0ubuntu1~precise~xup3 Tool of configuring the NVIDIA graphics driver ii nvidia-settings-updates 295.33-0ubuntu1 Tool of configuring the NVIDIA graphics driver After full reinstallation, including the remove of any previous nvidia drive, lsmod | grep -E 'nvidia|nouveau' returned: nvidia 10888310 46 dmesg | grep -C3 -E 'nouveau|NVRM' returned things like: [ 1875.607283] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1875.607289] nvidia 0000:01:00.0: setting latency timer to 64 [ 1875.607293] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=none [ 1875.607363] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 302.17 Tue Jun 12 16:03:22 PDT 2012 [ 1884.830035] nvidia 0000:01:00.0: PCI INT A disabled [ 1884.832058] bbswitch: disabling discrete graphics [ 1884.832960] bbswitch: Result of Optimus _DSM call: 09000019 Some programs, like Scilab, are now working fine under optirun(e.g. >optirun scilab) call. Thank you.

  Read the article

• atkbd.c spamming the logs. How to get rid? what is this?

  - by turbo

  On my Vostro 1000 notebook the following messages spam my dmesg: [18678.728936] atkbd.c: Unknown key released (translated set 2, code 0x8d on isa0060/serio0). [18678.728941] atkbd.c: Use 'setkeycodes e00d <keycode>' to make it known. [18679.831109] atkbd.c: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0). [18679.831119] atkbd.c: Use 'setkeycodes e00d <keycode>' to make it known. [18679.841607] atkbd.c: Unknown key released (translated set 2, code 0x8d on isa0060/serio0). [18679.841615] atkbd.c: Use 'setkeycodes e00d <keycode>' to make it known. [18680.901733] atkbd.c: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0). [18680.901744] atkbd.c: Use 'setkeycodes e00d <keycode>' to make it known. [18680.911536] atkbd.c: Unknown key released (translated set 2, code 0x8d on isa0060/serio0). [18680.911546] atkbd.c: Use 'setkeycodes e00d <keycode>' to make it known. It's most probably not from an actual key because it appears in regular intervals. First what is it? It could be my battery since it's nearly dead, as in loadable to 11 % of the initial capacity, but I have no evidence for that. What is this / how can I find out where this comes from? How can I get rid of it? Is there a 'dud' keycode? When I assign a keycode with sudo setkeycode e00d $(random keycode) the key does actually get pressed. That makes it impossible to enter sudo password for example. So any 'real' keycode is not an option. It hasn't been like that half a year ago. Even better than the dud keycode would be a real fix. It happens from 10.04 to 12.04 (before that I don't know). I did read zcat /usr/share/doc/udev/README.keymap.txt.gz |less as suggested in the Ubuntu Wiki. /lib/udev/findkeyboards && sudo /lib/udev/keymap -i input/event5 produces what appears to be newlines in rapid succession. sudo udevadm monitor doesn't show the event.

  Read the article

• External hard drive not recognized

  - by sr71

  Installed Ubuntu 10.10 on a hard drive by itself (no windows). All updates are up to date. Everything`works fine except when I plug in a 320 gig Toshiba external hard drive....it is not recognized. When I plug in an 8 gig flash drive it is recognized no problem. What do I mean by "not recognized"? I mean: how do you know it was not recognized. You can check the command "cat /proc/partitions" in a terminal with and without the hdd attached. If you see some difference, it's ok. If the difference is something like "sda1" (sd+letter+number) then you have partition on it, maybe it can't be handled in Ubuntu (no filesystem on it or so). If there is only "sda" in the difference for example (sd+letter, but no number after it) then the drive itself is detected, just no partition is created on it. Also you can check out the messages of the kernel, with the "dmesg" command in the terminal. If there is no disk/partition/anything in /proc/partitions, there can be an USB level problem, you can issue command "lsusb" as it was suggested before my answer. It's really matter of what do you mean about "not recognized". @Marco Ceppi @Oli @Pitto By "not recognized" I meant that when I plug in a 8 gig flash drive an icon immediately appears on the desktop imdicating that there is a flash drive plugged in and I can click on it and view the files on the flash drive. It also shows up on the "Nautilus" default file manager. When I plug in the 320 gig Toshiba external hard drive, I get no indication on the desktop or the file manager (thus "not recogized"). When I run the command cat/proc/partitions/ I get an error message Could not open location 'file:///home/bob/cat/proc/partitions' with or without the external hard drive installed. With the dmeg command I get about 10 pages of info with no mention of disk/partition/anything in /proc/partitions. When I run lsusb command I get the following: bob@bob-desktop:~$ lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 04b3:3003 IBM Corp. Rapid Access III Keyboard Bus 003 Device 002: ID 04b3:3004 IBM Corp. Media Access Pro Keyboard Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Black screen on latest Nvidia Cards when starting LightDM/Ubuntu

  - by Luis Alvarado

  Today I installed an Nvidia GT440 on my computer, changing the one that existed there, an Nvidia 9500GT. After changing it I started getting a problem where the screen just went black when loading the lightdm login screen (Where I punt my user and password). The thing is, if I disconnect the VGA cable and connect it again I get to see the lightdm greeter and everything works perfect. The problem is that I have to connect/disconnect every time I reboot the PC. I tried installing the 285.xx drivers. Same problem. I removed the Nvidia drivers installed with Jockey, rebooted, same problem. I install the current 280.xx again, same problem. After all that I installed a fresh install of Ubuntu, selected to install the Nvidia drivers while installing it from the livecd. After booting the same problem appeared. Dmesg does not say anything wrong about it. Same goes for the log from Jockey. What else should I check or what to do to solve it. Just to clarify, this does not happen BEFORE the lightdm greeter appears. Am guessing before the actual use of the video card with X starts with all the 2D/3D stuff that is used in ligthdm and unity. I can use any tty and even see the Ubuntu logo when starting. UPDATE: When I open a game in fullscreen the problem appears again. I have to unplug the monitor cable and plug it back in to see the game. Then when I quit the game I have to do it again to see the desktop. UPDATE 2: Today I bought a HDMI cable, connected the video card to the TV am testing it with and it actually did log in correctly without any black screen but it shows the resolution a little over the actual size of the screen. So I see only half of the launcher since the left side of it is hidden outside of the real resolution and the top bar is beyond the resolution. So the black screen is related to the VGA connection.

  Read the article

• Ubuntu hangs on booting up after a update

  - by alFReD NSH

  I've made a clean install yesterday, for the first time restarted, everything went good and then after I updated packages and copied my old home directory to replace the new one, when I restarted it hung when it was booting. I tried reinstalling again and doing the same thing, but again same thing happened. Here's what I see, before when the Ubuntu logo with the five dots is shown: Then after that, 3 or 4 of the dots will load and hangs there. If I press arrow up before that, this will be shown I started my laptop again today(the pictures are for the day before) and after that, boot up with live CD and got the logs. dmesg: http://pastebin.com/aVxV7BQF syslog: http://pastebin.com/4E2BrRUK And some info: alfred@alFitop:~$ uname -a Linux alFitop 3.2.0-24-generic #39-Ubuntu SMP Mon May 21 16:52:17 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lshw: http://pastebin.com/AZbKJmsT sources.list : http://pastebin.com/2HazmuyV My problem is a bit similar to here: http://ubuntuforums.org/showthread.php?t=1918271 Though I didn't change my x.org config. Only changed home directory and updated packages. I've tried memtest and fschk, both passed. In the recovery mode boot option, I've also realized that same things happen in failsafe graphical mode. But when I go into the network mode, I can boot up my system, but of course same the graphics are just basic. Adding blacklist intel_ips to /etc/modprobe.d/blacklist.conf solves the first message, but still I get the broken pipe and CPU stack traces. The current kernel version is 3.2.0-25, I've tried booting up in the 3.2.0-23(the one the installer came with, but same results.) Also uninstalled apparmor, didn't help. I've installed Ubuntu again, this time without copying the home directory, also same result. --- UPDATE --- This problem was solved before with removing backports, but its back again! I've updated my laptop last night and the problem came back. It's definitely one of these packages. My /var/log/apt/term.log and /var/log/apt/history.log. I'm almost having the same situation. --- UPDATE --- I realized this also have happened on times that I have updated(haven't restarted after it) and my computer power has been cut off and its shutdown due to lack of power. And I realized if I just do as I answered but not in somewhere without GUI(networking mode has the GUI) it wouldn't work.

  Read the article

• iwlwifi on lenovo z570 disabled by hardware switch

  - by Kevin Gallagher

  It was working fine with windows 7. The hardware switch is not disabled. I've toggled it back and forth dozens of times. The wifi light never turns on and it always lists as hardware disabled. I have the latest updates installed. I've been searching for solutions, but none of them seem to work for me. I've tried removing acer-wmi. I've tried setting 11n_disable=1. I've tried resetting the bios. I've tried using rfkill to unblock (only removes soft block). I've rebooted dozens of times. The wifi light turns off as soon as grub loads. Edit: I have a usb edimax wireless nic. It shows hardware disabled as well (although rfkill lists as unblocked). If I unload iwlwifi the usb nic works fine. uname -a `Linux xxx-Ideapad-Z570 3.2.0-55-generic #85-Ubuntu SMP Wed Oct 2 12:29:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linu`x rfkill list 19: phy18: Wireless LAN Soft blocked: no Hard blocked: yes dmesg [43463.022996] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [43463.023002] Copyright(c) 2003-2011 Intel Corporation [43463.023107] iwlwifi 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [43463.023190] iwlwifi 0000:03:00.0: setting latency timer to 64 [43463.023253] iwlwifi 0000:03:00.0: pci_resource_len = 0x00002000 [43463.023257] iwlwifi 0000:03:00.0: pci_resource_base = ffffc900057c8000 [43463.023261] iwlwifi 0000:03:00.0: HW Revision ID = 0x0 [43463.023797] iwlwifi 0000:03:00.0: irq 43 for MSI/MSI-X [43463.024013] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [43463.024250] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S [43463.045496] iwlwifi 0000:03:00.0: device EEPROM VER=0x15d, CALIB=0x6 [43463.045501] iwlwifi 0000:03:00.0: Device SKU: 0X50 [43463.045504] iwlwifi 0000:03:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [43463.045542] iwlwifi 0000:03:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [43463.045744] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio. [43463.047652] iwlwifi 0000:03:00.0: loaded firmware version 39.31.5.1 build 35138 [43463.047823] Registered led device: phy18-led [43463.047895] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [43463.048037] ieee80211 phy18: Selected rate control algorithm 'iwl-agn-rs' [43463.055533] ADDRCONF(NETDEV_UP): wlan0: link is not ready nm-tool State: connected (global) - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: unavailable Default: no HW Address: 74:E5:0B:4A:9F:C2 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points lshw -C network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:4a:9f:c2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-55-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:43 memory:f1500000-f1501fff lspci 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]

  Read the article

• Parallel Port Problem in 12.04

  - by Frank Oberle

  I have a “dumb” printer attached to a parallel port in my machine which works fine under the “other” resident operating system (from Redmond) on the same machine. I recently added Ubuntu 12.04 as a dual boot on the machine, but Ubuntu doesn't seem to recognize the parallel port at all. All I need to set up a printer is a really plain-vanilla fixed pitch text-only generic driver, which is present, but no parallel ports show up. (The other printers, all on USB ports, seem to work just fine). Following what appeared to me to be the most reasonable of the many conflicting pieces of advice on the web, here's what I did: I added the following lines to /etc/modules parport_pc ppdev parport Then, after rebooting, I checked to see that the lines were still present, and they were. I ran dmesg | grep par and got the following references in the output that seemed like they might have to do with the parallel port: [ 14.169511] parport_pc 0000:03:07.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 14.169516] PCI parallel port detected: 9710:9805, I/O at 0xce00(0xcd00), IRQ 21 [ 14.169577] parport0: PC-style at 0xce00 (0xcd00), irq 21, using FIFO [PCSPP,TRISTATE,COMPAT,ECP] [ 14.354254] lp0: using parport0 (interrupt-driven). [ 14.571358] ppdev: user-space parallel port driver [ 16.588304] type=1400 audit(1347226670.386:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=964 comm="apparmor_parser" [ 16.588756] type=1400 audit(1347226670.386:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=964 comm="apparmor_parser" [ 16.673679] type=1400 audit(1347226670.470:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1010 comm="apparmor_parser" [ 16.675252] type=1400 audit(1347226670.470:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1014 comm="apparmor_parser" [ 16.675716] type=1400 audit(1347226670.470:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1014 comm="apparmor_parser" [ 16.676636] type=1400 audit(1347226670.474:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1015 comm="apparmor_parser" [ 16.677124] type=1400 audit(1347226670.474:11): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1015 comm="apparmor_parser" [ 1545.725328] parport0: ppdev0 forgot to release port I have no idea what any of that means, but the line “parport0: ppdev0 forgot to release port ” seems unusual. I was still unable to add a printer for my old clunker, so I tried the direct approach, typing echo “Hello” > /dev/lp0 and received a Permission denied message. I then tried echo “Hello” > /dev/parport0 which didn't give me any message at all, but still didn't print anything. Running the command sudo /usr/lib/cups/backend/parallel gives the following: direct parallel:/dev/lp0 "unknown" "LPT #1" "" "" Checking the permissions for /dev/parport0, Owner, Group, and Other are all set to read and write. crw-rw---- 1 root lp 6, 0 Sep 9 16:37 /dev/lp0 crw-rw-rw- 1 root lp 99, 0 Sep 9 16:37 /dev/parport0 The output of the command lpinfo -v includes the following line: direct parallel:/dev/lp0 I've read several web postings that seem to suggest this has been a problem for several years, but the bug reports were closed because there wasn't enough information to address the issue (shades of Microsoft!). Any suggestions as to what I might be missing here?

  Read the article

• How to troubleshoot ethernet port on laptop

  - by Psallas Vassilios

  I have a problem with my wired connection. To be more specific, my laptop doesn't seems to recognize that I have plugged in an ethernet cable. I tried to download new drivers for my ethernet card, but I couldn't find any solutions. Maybe because I am new to Linux, so I'm not familiar with running commands in the terminal. OK I have typed the command and here are the results: 00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter [1039:0191] (rev 02) For the second reply I don't know if the following is what you asked me: ?Memory: 3.9 GiB ?Processor: Intel Core 2 Duo CPU P8800 @ 2.66GHz × 2 ?OS type: 32-bit My Ethernet connection had some problem on Windows too. I have changed recently my internet provider, and since then my ethernet cable is not recognized by the laptop. At that time I was still on Windows. I thought that with Ubuntu the problem would be solved, but unfortunately the problem still persists. If someone can help me to solve my problem I'll be thankful. Here are the results of the three first commands you told me to run: lsmod | grep sis190 sis190 22570 0 sudo modprobe sis190 ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:90:81:7e UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:185 errors:0 dropped:0 overruns:0 frame:0 TX packets:185 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22672 (22.6 KB) TX bytes:22672 (22.6 KB) wlan0 Link encap:Ethernet HWaddr 00:25:d3:2c:3a:ae inet addr:192.168.1.72 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::225:d3ff:fe2c:3aae/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:260 errors:0 dropped:0 overruns:0 frame:0 TX packets:363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:71992 (71.9 KB) TX bytes:52000 (52.0 KB) and the results of running the last two commands: dmesg | grep -e eth -e sis190 [ 0.816667] sis190: sis190 Gigabit Ethernet driver 1.4 loaded [ 0.816728] sis190 0000:00:04.0: setting latency timer to 64 [ 0.816751] sis190: 0000:00:04.0: Read MAC address from EEPROM [ 0.904032] sis190: 0000:00:04.0: Realtek PHY RTL8201 transceiver at address [ 1.416030] sis190: 0000:00:04.0: Using transceiver at address 1 as default [ 1.448235] sis190 0000:00:04.0: eth0: 0000:00:04.0: SiS 191 PCI Gigabit Ethernet adapter at f8410000 (IRQ: 19), 00:90:f5:90:81:7e [ 1.448238] sis190 0000:00:04.0: eth0: GMII mode. [ 1.448243] sis190 0000:00:04.0: eth0: Enabling Auto-negotiation [ 11.560907] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372019] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372265] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 26.424038] sis190 0000:00:04.0: eth0: auto-negotiating... nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: sis190 State: unavailable Default: no HW Address: 00:90:F5:90:81:7E Capabilities: Carrier Detect: yes Wired Properties Carrier: off

  Read the article

• What does Ubuntu do when I signal undocking to a laptop?

  - by Seppo Erviälä

  It seems that Ubuntu runs some script or command when I signal that I want to undock my laptop by pressing the undock button on the dock. Most visible thing that happens is that resolution on external display is changed. After prepearing for undock my laptop is still connected to power, VGA-output and audio jacks through dock but not to any usb devices or optical drive. I'm running 11.04 on a ThinkPad X61s with X6 UltraBase. What happens when I signal undocking? This is what dmesg says after pressing undock button: [81459.990682] ata1.00: disabled [81459.990727] ata1.00: detaching (SCSI 0:0:0:0) [81459.991722] ACPI: \_SB_.GDCK - undocking [81460.009462] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0 [81460.020252] ehci_hcd 0000:00:1a.7: BAR 0: set to [mem 0xfe226c00-0xfe226fff] (PCI address [0xfe226c00-0xfe226fff]) [81460.020265] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0 [81460.020281] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30b) [81460.020309] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102) [81460.020338] ehci_hcd 0000:00:1a.7: PME# disabled [81460.020346] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0 [81460.020352] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0 [81460.020363] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [81460.020372] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [81460.020432] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0 [81460.040071] ehci_hcd 0000:00:1d.7: BAR 0: set to [mem 0xfe227000-0xfe2273ff] (PCI address [0xfe227000-0xfe2273ff]) [81460.040085] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0 [81460.040104] ehci_hcd 0000:00:1d.7: restoring config space at offset 0xf (was 0x400, writing 0x40b) [81460.040133] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102) [81460.040170] ehci_hcd 0000:00:1d.7: PME# disabled [81460.040178] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0 [81460.040184] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0 [81460.040195] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [81460.040204] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [81460.040503] ehci_hcd 0000:00:1d.7: PCI INT D disabled [81460.040552] ehci_hcd 0000:00:1d.7: PME# enabled [81460.061657] ehci_hcd 0000:00:1d.7: power state changed by ACPI to D3 [81460.200414] usb 1-4: USB disconnect, address 14 [81462.220088] ehci_hcd 0000:00:1a.7: PCI INT C disabled [81462.220169] ehci_hcd 0000:00:1a.7: PME# enabled [81462.240115] ehci_hcd 0000:00:1a.7: power state changed by ACPI to D3

  Read the article

• Ubuntu 10.10 not recognizing external hard drive

  - by sr71

  Installed Ubuntu 10.10 on a hard drive by itself (no windows). All updates are up to date. Everything`works fine except when I plug in a 320 gig Toshiba external hard drive....it is not recognized. When I plug in an 8 gig flash drive it is recognized no problem. What do I mean by "not recognized"? I mean: how do you know it was not recognized. You can check the command "cat /proc/partitions" in a terminal with and without the hdd attached. If you see some difference, it's ok. If the difference is something like "sda1" (sd+letter+number) then you have partition on it, maybe it can't be handled in Ubuntu (no filesystem on it or so). If there is only "sda" in the difference for example (sd+letter, but no number after it) then the drive itself is detected, just no partition is created on it. Also you can check out the messages of the kernel, with the "dmesg" command in the terminal. If there is no disk/partition/anything in /proc/partitions, there can be an USB level problem, you can issue command "lsusb" as it was suggested before my answer. It's really matter of what do you mean about "not recognized". @Marco Ceppi @Oli @Pitto By "not recognized" I meant that when I plug in a 8 gig flash drive an icon immediately appears on the desktop imdicating that there is a flash drive plugged in and I can click on it and view the files on the flash drive. It also shows up on the "Nautilus" default file manager. When I plug in the 320 gig Toshiba external hard drive, I get no indication on the desktop or the file manager (thus "not recogized"). When I run the command "cat/proc/partitions/" I get an error message Could not open location 'file:///home/bob/cat/proc/partitions' with or without the external hard drive installed. With the "dmeg" command I get about 10 pages of info with no mention of disk/partition/anything in /proc/partitions. When I run "lsub" command I get the following: bob@bob-desktop:~$ lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 04b3:3003 IBM Corp. Rapid Access III Keyboard Bus 003 Device 002: ID 04b3:3004 IBM Corp. Media Access Pro Keyboard Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub bob@bob-desktop:~$

  Read the article

• The Internet Key Wave MW833UP is not recognized in Ubuntu

  - by gio900

  I can't use my Onda MW833UP... :( Any advice? Here is something that someone else may understand: ~$: lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric ~$: lsusb Bus 001 Device 005: ID 1ee8:0012 ~$: dmesg [ 22.709475] cdc_acm 1-1:1.0: ttyACM0: USB ACM device [ 22.714856] usbcore: registered new interface driver cdc_acm [ 22.714866] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 23.520490] ieee80211 phy0: wl_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) [ 24.244530] usbcore: registered new interface driver usbserial [ 24.244575] USB Serial support registered for generic [ 24.244673] usbcore: registered new interface driver usbserial_generic [ 24.244681] usbserial: USB Serial Driver core [ 24.265879] USB Serial support registered for GSM modem (1-port) [ 24.285680] usbcore: registered new interface driver option [ 24.285691] option: v0.7.2:USB Driver for GSM modems [ 24.425878] EXT4-fs (sda9): re-mounted. Opts: errors=remount-ro,commit=600 [ 24.736540] EXT4-fs (sda8): re-mounted. Opts: commit=600 [ 35.705796] Easy slow down manager: checking for SABI support. [ 35.706002] Easy slow down manager: SABI is supported (f5189) [ 36.060099] usbcore: deregistering interface driver uvcvideo [ 139.508061] CE: hpet increased min_delta_ns to 20113 nsec [ 6798.378917] usb 1-1: USB disconnect, device number 5 [ 6809.108232] usb 1-1: new high speed USB device number 6 using ehci_hcd [ 6809.242692] scsi5 : usb-storage 1-1:1.0 [ 6810.241257] scsi 5:0:0:0: CD-ROM Onda Datacard CD-ROM 0001 PQ: 0 ANSI: 0 [ 6810.241841] scsi 5:0:0:1: Direct-Access Onda Storage 0001 PQ: 0 ANSI: 0 [ 6810.271410] sr0: scsi3-mmc drive: 0x/0x caddy [ 6810.272099] sr 5:0:0:0: Attached scsi CD-ROM sr0 [ 6810.272852] sr 5:0:0:0: Attached scsi generic sg1 type 5 [ 6810.279954] sd 5:0:0:1: [sdb] Attached SCSI removable disk [ 6810.281210] sd 5:0:0:1: Attached scsi generic sg2 type 0 [ 6810.380591] sr0: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00 [ 6810.380617] sr: Sense Key : Hardware Error [current] [ 6810.380625] sr: Add. Sense: No additional sense information [ 6810.613937] sr0: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00 [ 6810.613972] sr: Sense Key : Hardware Error [current] [ 6810.613984] sr: Add. Sense: No additional sense information [ 6810.673716] usb 1-1: USB disconnect, device number 6 [ 6815.572142] usb 1-1: new high speed USB device number 7 using ehci_hcd [ 6815.706828] cdc_acm 1-1:1.0: ttyACM0: USB ACM device The last 3 lines are where I inserted the Internet key, then reconnected it. usb-device T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1ee8 ProdID=0012 Rev=00.01 S: Manufacturer=Onda S: Product=MW833UP S: SerialNumber=9230B35D870F9CB7AE684EACC5C12BE5EC33B26E C: #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=01 Driver=cdc_acm I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm Then there is /dev/ttyACM0. When the key is connected to the USB port, everything that will meant...

  Read the article

• sony vaio WLAN problem using 12.04

  - by Fredrik

  I'm unable to get my WLAN to work for my Sony Vaio model VPCF23C5E No problem connecting from windows, smartphones etc. $ sudo lshw -C network; lsb_release -a; uname -a; sudo rfkill list; dmesg | grep -i firm *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 64:27:37:92:99:0f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-29-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:f7000000-f707ffff memory:f7080000-f708ffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 06 serial: f0:bf:97:dd:b2:bd size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-1.fw ip=192.168.1.4 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:50 ioport:9000(size=256) memory:e2104000-e2104fff memory:e2100000-e2103fff LSB Version: core-2.0-amd64:core-2.0-noarch:core-3.0-amd64:core-3.0-noarch:core-3.1-amd64:core-3.1-noarch:core-3.2-amd64:core-3.2-noarch:core-4.0-amd64:core-4.0-noarch Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise Linux siriedit 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no [ 1.287449] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 18.273582] [Firmware Bug]: ACPI(NGFX) defines _DOD but not _DOS Seen some proposed solution e.g. Wireless network cannot be enabled for Sony VAIO E series but answers there don't solve my problem... I'm out of ideas :-( What else can I check? update $ ifconfig -a eth0 Link encap:Ethernet HWaddr f0:bf:97:dd:b2:bd inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::f2bf:97ff:fedd:b2bd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5072 errors:0 dropped:0 overruns:0 frame:0 TX packets:4444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4568435 (4.5 MB) TX bytes:610624 (610.6 KB) Interrupt:50 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1498 errors:0 dropped:0 overruns:0 frame:0 TX packets:1498 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:114156 (114.1 KB) TX bytes:114156 (114.1 KB) wlan0 Link encap:Ethernet HWaddr 64:27:37:92:99:0f inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6627:37ff:fe92:990f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1277 errors:0 dropped:0 overruns:0 frame:0 TX packets:472 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:483155 (483.1 KB) TX bytes:61031 (61.0 KB)

  Read the article

• Fuji camera "mounts" but folder not in Dolphin After Kubuntu 13.10 upgrade

  - by user207207

  Fuji camera mount reported in attached devices but not visible in Dolphin After Kubuntu 13.10 upgrade Have reinstalled the driver, and a few other suggestions, for other cameras mounts failing on previous Ubuntu upgrades. I have already spent a couple of hours trying to get my photo's off the camera, very annoying. Worked perfectly in 11.04, 11.10, 12.04, 12.10 and 13.04. dmesg | tail; lsusb; lsb_release -a [ 6181.858786] CPUM: APIC 03 at 00000000fee00000 (mapped at ffffc90009400000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396236] CPUM: APIC 00 at 00000000fee00000 (mapped at ffffc90000c6a000) - ver 0x80050010, lint0=0x10700 lint1=0x00400 pc=0x00400 thmr=0x10000 [17261.396239] CPUM: APIC 03 at 00000000fee00000 (mapped at ffffc90000c72000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396241] CPUM: APIC 02 at 00000000fee00000 (mapped at ffffc90000c70000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396255] CPUM: APIC 01 at 00000000fee00000 (mapped at ffffc90000c6e000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [32456.884907] usb 2-5: new high-speed USB device number 2 using ehci-pci [32457.654046] usb 2-5: New USB device found, idVendor=04cb, idProduct=01e8 [32457.654050] usb 2-5: New USB device strings: Mfr=0, Product=2, SerialNumber=3 [32457.654052] usb 2-5: Product: Digital Camera [32457.654053] usb 2-5: SerialNumber: 4C3230302020091117CAA59WP18548 Bus 002 Device 002: ID 04cb:01e8 Fuji Photo Film Co., Ltd Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 2013:024f PCTV Systems nanoStick T2 290e Bus 001 Device 002: ID 046d:082d Logitech, Inc. HD Pro Webcam C920 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub No LSB modules are available. Distributor ID: Ubuntu vissibleDescription: Ubuntu 13.10 Release: 13.10 Codename: saucy sudo apt-get install gvfs-bin gvfs-mount gphoto2://[usb:002,002] Error mounting location: Error initializing camera: -108: No such file or directory ...... I have reported a bug in Dolphin, which has been transferred to Solid. Further information : I ran solid-hardware list details udi = '/org/kde/solid/udev/sys/devices/pci0000:00/0000:00:04.1/usb2/2-5' parent = '/org/kde/solid/udev' (string) vendor = '04cb' (string) product = 'Digital Camera' (string) description = 'Camera' (string) Block.major = 189 (0xbd) (int) Block.minor = 137 (0x89) (int) Block.device = '/dev/bus/usb/002/010' (string) Camera.supportedProtocols = {'ptp'} (string list) Camera.supportedDrivers = {'gphoto'} (string list) I still can't get my photo's off, I can see the folders using the Gimp menu. If anyone has got any ideas, I'm willing to try them.

  Read the article

• fdisk shows overlapping partitions

  - by Campa

  At every boot to start Ubuntu, a partition gets re-mounted more than 1 times, sometimes causing very long boots. Example below: > dmesg ... [ 21.472020] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro ... [ 42.021537] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0 ... I suspect there is a problem of overlapping partitions here, regarding sda4 and sda5: > sudo fdisk -l Device Boot Start End Blocks Id System /dev/sda1 63 610469 305203+ de Dell Utility /dev/sda2 612352 32069631 15728640 7 HPFS/NTFS/exFAT /dev/sda3 * 32069632 238979788 103455078+ 7 HPFS/NTFS/exFAT /dev/sda4 238983166 625141759 193079297 5 Extended /dev/sda5 238983168 612630527 186823680 83 Linux /dev/sda6 612632576 625141759 6254592 82 Linux swap / Solaris Further details: > more /etc/fstab ... # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda6 during installation UUID=b33be99b-5c9e-449e-ad48-be608aeff001 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda7 during installation UUID=7c9071cc-b77b-40da-9f80-6b8a9a220cb1 none swap sw and > mount /dev/sda5 on / type ext4 (rw,errors=remount-ro,commit=0) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) fusectl on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) gvfs-fuse-daemon on /home/piero/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=piero) I am Running Ubuntu Oneiric + LXDE on Dell Studio XPS machine 64-bit, dual booting with Windows 7. A months ago, I resized the Ubuntu partition and maybe I messed up something by doing that. Do you have any idea, why this long booting is happening?

  Read the article

• Send raw data to USB parallel port after upgrading to 11.10 oneiric

  - by zaphod

  I have a laser cutter connected via a generic USB to parallel adapter. The laser cutter speaks HPGL, as it happens, but since this is a laser cutter and not a plotter, I usually want to generate the HPGL myself, since I care about the ordering, speed, and direction of cuts and so on. In previous versions of Ubuntu, I was able to print to the cutter by copying an HPGL file directly to the corresponding USB "lp" device. For example: cp foo.plt /dev/usblp1 Well, I just upgraded to Ubuntu 11.10 oneiric, and I can't find any "lp" devices in /dev anymore. D'oh! What's the preferred way to send raw data to a parallel port in Ubuntu? I've tried System Settings Printing + Add, hoping that I might be able to associate my device with some kind of "raw printer" driver and print to it with a command like lp -d LaserCutter foo.plt But my USB to parallel adapter doesn't seem to show up in the list. What I do see are my HP Color LaserJet, two USB-to-serial adapters, "Enter URI", and "Network Printer". Meanwhile, over in /dev, I do see /dev/ttyUSB0 and /dev/ttyUSB1 devices for the 2 USB-to-serial adapters. I don't see anything obvious corresponding to the HP printer (which was /dev/usblp0 prior to the upgrade), except for generic USB stuff. For example, sudo find /dev | grep lp produces no output. I do seem to be able to print to the HP printer just fine, though. The printer setup GUI gives it a device URI starting with "hp:" which isn't much help for the parallel adapter. The CUPS administrator's guide makes it sound like I might need to feed it a device URI of the form parallel:/dev/SOMETHING, but of course if I had a /dev/SOMETHING I'd probably just go on writing to it directly. Here's what dmesg says after I disconnect and reconnect the device from the USB port: [ 924.722906] usb 1-1.1.4: USB disconnect, device number 7 [ 959.993002] usb 1-1.1.4: new full speed USB device number 8 using ehci_hcd And here's how it shows up in lsusb -v: Bus 001 Device 008: ID 1a86:7584 QinHeng Electronics CH340S Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x1a86 QinHeng Electronics idProduct 0x7584 CH340S bcdDevice 2.52 iManufacturer 0 iProduct 2 USB2.0-Print iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 96mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 7 Printer bInterfaceSubClass 1 Printer bInterfaceProtocol 2 Bidirectional iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Device Status: 0x0000 (Bus Powered)

  Read the article

• External 1TB WD USB 3.0 HDD is not detecting. Working perfectly find in Windows

  - by Yathi

  My 1TB USB 3.0 was working fine earlier in Ubuntu as well as Windows. But lately it is not at all being detected in Ubuntu. It still works fine in Windows. I did update my Ubuntu to 12.10 but I am not sure if that caused the issue. When I connect my HDD and run dmesg | tail: [ 47.804676] usb 4-3: >Device not responding to set address. [ 48.008575] usb 4-3: >Device not responding to set address. [ 48.212421] usb 4-3: >device not accepting address 9, error -71 [ 48.324451] usb 4-3: >Device not responding to set address. [ 48.528340] usb 4-3: >Device not responding to set address. [ 48.732165] usb 4-3: >device not accepting address 10, error -71 [ 48.844138] usb 4-3: >Device not responding to set address. [ 49.048179] usb 4-3: >Device not responding to set address. [ 49.251881] usb 4-3: >device not accepting address 11, error -71 [ 49.251907] hub 4-0:1.0: >unable to enumerate USB device on port 3 The output of sudo fdisk -l is : Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00030cde Device Boot Start End Blocks Id System /dev/sda1 2048 1332981759 666489856 83 Linux /dev/sda2 1332981760 1953523711 310270976 5 Extended /dev/sda5 1332983808 1349365759 8190976 82 Linux swap / Solaris /dev/sda6 1349367808 1953523711 302077952 7 HPFS/NTFS/exFAT Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000a2519 Device Boot Start End Blocks Id System /dev/sdb1 * 2048 103368703 51683328 7 HPFS/NTFS/exFAT /dev/sdb2 103368704 154568703 25600000 83 Linux /dev/sdb3 154568704 234440703 39936000 7 HPFS/NTFS/exFAT /dev/sda and /dev/sdb are my 2 internal HDDs. But the external one which should be /dev/sdc is not even being shown though it is connected and the LED on the HDD is glowing. Someone had suggested adding blacklist uas to /etc/modprobe.d/blacklist.conf. Tried that as well. But still not working. Can someone help me out.

  Read the article

• xt_TCPMSS: bad length messages

  - by Matic

  I'm getting loads of messages like: Jun 23 10:24:20 awakening kernel: [ 1691.596823] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663362] xt_TCPMSS: bad length (1448 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663495] xt_TCPMSS: bad length (1448 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663588] xt_TCPMSS: bad length (1448 bytes) Jun 23 10:24:21 awakening kernel: [ 1692.663671] xt_TCPMSS: bad length (1440 bytes) Jun 23 10:24:26 awakening kernel: [ 1697.062914] xt_TCPMSS: bad length (474 bytes) Jun 23 10:24:26 awakening kernel: [ 1697.305525] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:27 awakening kernel: [ 1698.946633] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:36 awakening kernel: [ 1707.481198] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:37 awakening kernel: [ 1708.723526] xt_TCPMSS: bad length (805 bytes) Jun 23 10:24:38 awakening kernel: [ 1709.599461] xt_TCPMSS: bad length (805 bytes) Jun 23 10:24:41 awakening kernel: [ 1712.211052] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:41 awakening kernel: [ 1712.260588] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:41 awakening kernel: [ 1712.976058] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:43 awakening kernel: [ 1714.225209] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:43 awakening kernel: [ 1714.914961] xt_TCPMSS: bad length (1492 bytes) Jun 23 10:24:55 awakening kernel: [ 1726.192696] xt_TCPMSS: bad length (1480 bytes) Jun 23 10:24:55 awakening kernel: [ 1726.192825] xt_TCPMSS: bad length (1480 bytes) In my dmesg/syslog. This linux machine is among other things used as an internet gateway. Connection is over PPPoE. I have the following line in my iptables script: $IPT -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu # PPPoE fix The frequency of this messages increased 10x when I upgraded from Debian lenny with 2.6.27 to squeeze with 2.6.32 few days ago. Why am I seeing this messages and how can I fix them?

  Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >