Search Results

Search found 456 results on 19 pages for 'equipment'.

Page 15/19 | < Previous Page | 11 12 13 14 15 16 17 18 19  | Next Page >

  • ADSL2+ - High sync-rate, good line attenuation, but low noise margin and slow speeds

    - by Mark Pim
    I've been with my ISP (IdNet) for a few months and have been getting some good speeds, but in the last week the speed has dramatically decreased (from 15 Mbps+ to around 0.2 Mbps). This happens at all times of day, not just peak periods. Obviously I've done all I can to isolate problems my end - only one PC is connected to the router (via ethernet cable) and no other background programs are using the network etc. I've raised the issue with the ISP and they've suggested trying a new ADSL filter to see if that is casuing the problem, but I thought it would also be good to get the opinion of superuser on possible causes or other troubleshooting I can do. Here are the juicy stats :) My router (Netgear DGN1000) reports: Downstream Upstream Connection Speed 17602 kbps 1062 kbps Line Attenuation 17.9 db 8.6 db Noise Margin 6.0 db 6.1 db I used RouterStats and it seems to show those figures stay fairly consistent all the time I ran the BT speedtest and it reported: download speed of 164 kbps, out of a max achievable of 21000 kbps upload speed of 859 kbps, out of 1048 kbps DSL connection rate 17719 kbps down and 1048 kbps up IP Profile of 15000 kbps Is there any more troubleshooting I can do? Does this look like a problem with my equipment / wiring or with BT's line? Any advice would be great :)

    Read the article

  • Standing and sitting while using a computer at work

    - by Adam Batkin
    I would like to be able to comfortably switch between sitting and standing while at work (I'm a software developer, so I spend most of my day in front of a computer). For the past couple of months I have been using a large elevated stand that sits on my desk (designed expressly for this purpose) containing my keyboard and mouse, and my monitors have been raised as high as possible and aimed upwards. So I can stand all day and I'm pretty comfortable (my right wrist may be at too much of an angle when it's on my mouse, but that's a separate issue). The only problem is that sometimes I want to be able to sit. I can easily place my keyboard and mouse back down under the elevated stand, but I have to look up pretty steeply and that is uncomfortable and makes it difficult to see the screens since they are tilted upwards. My monitor mounts are difficult to adjust quickly/easily, so I can't just re-aim them. I would of course love one of those hydraulic standing/sitting desks (cost isn't the problem). But I'm in a row of "trader-style" desks where it's basically a very long surface with people sitting at 6-foot intervals. What type of equipment do you recommend? I suppose the best thing would be some sort of monitor stand (it must be able to hold 2-3 LCDs) that can easily be lowered and raised. But any other suggestions are also welcome.

    Read the article

  • disk write cache buffer and separate power supply

    - by HugoRune
    Windows has a setting to turn off the write-cache buffer (see image) Turn off Windows write-cache buffer flushing on the device To prevent data loss, do not select this check box unless the device has a separate power supply that allows the device to flush its buffer in case of power failure. Is it feasible and economical to get such a "separate power supply" for the internal sata drives of a non-server PC? Under what name is such a power supply sold? I know that there are UPS devices that can be connected to external drives,but what is required to be able to switch this setting safely on for an internal disk? The setting has different descriptions in different version of windows Windows XP: Enable write caching on the disk This setting enables write caching in Windows to improve disk performance, but a power outage or equipment failure might result in data loss or corruption. Windows Server 2003: Enable write caching on the disk Recommended only for disks with a backup power supply. This setting further improves disk performance, but it also increases the risk of data loss if the disk loses power. Windows Vista: Enable advanced performance Recommended only for disks with a backup power supply. This setting further improves disk performance, but it also increases the risk of data loss if the disk loses power. Windows 7 and 8: Turn off Windows write-cache buffer flushing on the device To prevent data loss, do not select this check box unless the device has a separate power supply that allows the device to flush its buffer in case of power failure. This article by Raymond Chen has some more detailed information about what the setting does.

    Read the article

  • How to Monitor Network in Medium-Sized Company?

    - by Kyle Lowry
    I work at a medium sized company (100+ employees). An issue that has been cropping up is network performance, internet access in particular. We have about 70 or more computers, a mix of Mac OS X and Windows XP & 7 machines. We have several servers (Exchange server, PC file servers, MS SQL, Blackberry, FTP, Mac server, etc). There are four main switches, a SonicWall firewall, and probably a couple routers in the server room with a dozen or so more scattered around the building. The network structure has grown organically over a number of years; and, as far as I know, there really isn't a monitoring solution in place. When we experience network issues (slow connections, dropped packets, and so on), our general solution is to power cycle some hardware or go around to each employee and ask them if they are uploading/downloading any large files. This is really inefficient and time consuming, and it does not allow us to monitor the network, tackling potential problems proactively. I would like to find a solution that would allow me to monitor network usage company-wide in real time, with detail going down to the individual computer, ideally. Given the hodgepodge of equipment and operating systems, what would be the best way to set up some kind of monitoring solution? Hardware, software, restructuring our network architecture?

    Read the article

  • Query specific nameserver for a particular domain upon VPN connect

    - by MT
    Some background: I have a work laptop with Ubuntu 9.10 on it. I have a small network at home where I've been running some basic services (for myself/my family) for 10 some years. In my home network there is a nameserver (Fedora) running Bind 9 with two "views". One view is the "outside" view and it provides name resolution (to the Internet at large) for email, a wiki, and a couple of blogs. The "inside" view provides name resolution (to the internal RFC1918 addresses of theses servers) as well as all the inside hosts, network equipment, ...etc. I connect with an openvpn client to my home network from outside (such as work). What I'd like to be able to do is resolve names on my internal network across this VPN (so I get the RFC1918 "inside" responses) without fully changing my resolver to the DNS server at my hose. For example, if I connect to the VPN from work, I can change my resolver (by editing resolv.conf) to the DNS server at my house (across the VPN) and then successfully resolve all of the inside DNS names on my home network. The issue I have with this is that now I'm no longer able to resolve "inside" names provided by my work's DNS servers (because I'm using my home DNS server). Alternatively, I can connect to the VPN and access my home severs via IP addresses directly, but this is inconvenient and causes issues with Apache name-based hosting (among other things). In the end, the effect I'm trying to achieve is as follows: When I connect to the VPN I automatically start sending DNS requests for *.myhomedomain.com to my home nameserver, but any other requests continue to go the the nameserver I was using before (the one I received on my company LAN via DHCP). When I disconnect the VPN, requests for *.myhomedomain.com go back to the local LAN DNS server (e.g. all requests are going there now). I'm looking for suggestion at to how this can be accomplished.

    Read the article

  • Setting up a home network

    - by Mat Richardson
    I'm trying to get my head around how to do this with the equipment I have. Here's how it is.. I have an old laptop that has server 2003 installed on it. This has no wireless NIC, but I have a spare wireless router that I can wire to it. We have a virgin wireless router which provides the home with internet access. What I would like to do it make resources on the server 2003 machine available to the rest of the devices in the home - specifically a couple of laptops running windows 7. Ideally I'd like to be able to use the laptop as a fileserver but maybe also offer application virtualization. In the first instance however, I'd like to create a file server with the laptop and allow connections to it by the other machines. Virtualisation is just a 'nice to have'... Given the hardware I have is this possible? Can you point me in the right direction how to do what I want if this is the case?

    Read the article

  • Workaround for Dell "Power Supply Not Recognised" issue

    - by Haedrian
    So, I have a Dell Inspirion and the power supply port appears to be damaged. Basically when I plug it in I get a nice popup telling me that it couldn't detect that its a Dell power supply so it won't charge the battery and underclocks the system. It still works for other purposes (that is, giving power) I thought it was the actual power supply cable so I bought a new one, that worked for a while, provided I inserted it at JUST THE RIGHT angle. But now that's not working anymore, so I assume its the part which connects to the computer. The battery charging I can live without, the underclocking I can't. I'd like a way around this issue. Things I've tried: Updating the BIOS Replacing the power supply cable Inserting it at different angles Turning it off and on again Swearing at it Twisting it while inserting it So, is there a workaround somehow? I'd like to avoid taking out my soldering kit and risking permanently damaging expensive equipment if that's allright. I'm hoping for a software solution. Added: The exact model is a Del Inspirion N5010

    Read the article

  • Is it possible to add a WiFi HotSpot to an already established LAN, keep the two separate, and not modify the primary router?

    - by user12844
    I have a set up where my Cisco ASA is sitting in one facility, providing access to the Internet for two buildings. The two buildings are geographically separated by a Wireless Bridge spanning about 10 miles. All computers and equipment inside the LAN are on the same subnet (its pretty small) and we have WiFi AP's in both locations providing Wired and Wireless access to the LAN. Given all the BYOD (Ipods, and SmartPhones etc...) coming into the office as well as Visiting reps etc... we would like to also provide a non-secure, device independent (the devices cannot see or communicate with each other), and LAN independent (the devices cannot see or use anything on the LAN) HotSpot that anyone could use for their Devices that gives them access to the Internet ONLY without needing a password. I get that this could be possible at the facility with my Cisco if I messed with it and created VLANs etc... but then I would need to get it across my Bridge as well and don't think that would be possible without serious reconfiguration of everything. Would really like some kind of magic drop in solution that can kind of piggy back on my LAN without really needing to do very many if any changes to the current set up.

    Read the article

  • Linux that restores itself on each reboot

    - by jettero
    I'm looking for methods and software to help create a variant of lubuntu that will restore itself to an install state and/or update on every boot. I'm thinking of doing things like putting the root filesystem on a squashfs and using unionfs and tmpfs to make root writable, but automagically restorable. I'm thinking of updating the squashfs with rsync. Perhaps there are other ways to approach the problem. Perhaps root needn't be writable at all. All thoughts welcome. The home dir would be writable in the usual way. The goal, if it matters, is a Linux that's simple to maintain from the home office, but that functions correctly for customers. We have some custom software that we wish for customers to be able to run trivially on equipment we provide. Ideally these devices would have a "restore to factory" function that would put it back the way we intended. If this is part of the normal boot cycle, so much the better. Why lubuntu? Personal preference for this application. It has a usable desktop, but doesn't take up much ram.

    Read the article

  • Working with an external button box

    - by Scott
    I tried this question on Stack Overflow, but I was pointed here, so here goes: For a new project for myself, I am looking for a way to be able to (for example) open a pop-up window on my laptop, by pressing a button on an external device (to be build by myself, or at least bought) connected with USB. Basically I would be looking at something like a Arduino or Raspberry (IF I am looking in the right direction) with buttons on it, and as soon as I hit a button on the external box with physical buttons, a command activates on my laptop and for example opens a popup window in which I can input tekst. Does anyone know: 1) if it is possible to do this at all. 2) What equipment is needed for the external box, what programming is needed. I preffer .net (dot net) but maybe it can only be done with software from the external box. If anyone can point me in the right direction, like make/model of the external box or websites I would be very happy. I have knowledge of Visual Studio/.net but I am willing to learn other languages if .net is not an option for this project. Thanks in advance Scott PS: If anyone knows of some better tags, or at least knows what I mean and needs me to edit the question, please do tell me... I am new on Stack Overflow/Superuser.

    Read the article

  • How to train users converting from PC to Mac/Apple at a small non profit?

    - by Everette Mills
    Background: I am part of a team that provides volunteer tech support to a local non profit. We are in the position to obtain a grant to update almost all of our computers (many of them 5 to 7 year old machines running XP), provide laptops for users that need them, etc. We are considering switching our users from PC (WinXP) to Macs. The technical aspects of switching will not be an issue for the team. We are in the process of planning data conversions, machine setup, server changes, etc regardless of whether we switch to Macs or much newer PCs. About 1/4 of the staff uses or has access to a Mac at home, these users already understand the basics of using the equipment. We have another set of (generally younger) users that are technically savvy and while slightly inconvenienced and slowed for a few days should be able to switch over quickly. Finally, several members of the staff are older and have many issues using there computers today. We think in the long run switching to Macs may provide a better user experience, fewer IT headaches, and more effective use of computers. The questions we have is what resources and training (webpages, Books, online training materials or online courses) do you recommend that we provide to users to enable the switchover to happen smoothly. Especially, with a focus on providing different levels of training and support to users with different skill levels. If you have done this in your own organization, what steps were successful, what areas were less successful?

    Read the article

  • Compare cells in two different spreadsheets and extract data from one an place it in the other if match found

    - by Fergie
    I need to find a way to compare two spreadsheets and if there is a match on specific cells, pull data from one sheet to another. Say the two spreadsheets contain a value that identifies a piece of equipment: spreadsheet 1 spreadsheet 2 Server Server Serial # 123abc 123abc 123-xx-456 There are of course many, many records/rows in each sheet. I need to look at the first cell in the server column of sheet 1 and then search a range of cells in the sever column of sheet 2 for a match. If there is a match, I need to pull the serial # value from the cell in the matching row an put it into the serial # cell of the matching row in sheet 1 (all of the "serial #" cells in sheet 1 are presently empty.) If that description explaination is too convoluted I can explain by answering any questions you may have. My deadline for this task is Noon tomorrow, 30 Aug 2012. Yes, I got the task today at noon.... I am not an Excel user and just get thrust into it on occassion... Any help would be a huge assist.

    Read the article

  • Personal projects competing with employers projects?

    - by jamesorwood123
    Recently at my place of employment it was discovered that I was developing an outside personal project (personal project being a project I have been working on, in my spare time, for my own purposes, using my personal equipment). My employer has an idea which is very similar to my outside project but has not been started, created, put out to market yet. When I originally started working for the company I signed a non-compete contract. My employer is now saying that because my outside/personal project is similar to theirs that I am now a competitor and breaching my original non-compete agreement. What I would like to know is where do I stand in this situation? Also my personal project has not been fully developed, nor is available to anyone other than myself. So if we both don’t have full/released products (full meaning put out to the public) are we actually competitors? There is going to be a meeting in the coming weeks to discuss this issue and would like to have a proper argument in place. I know some of this conversation is best held with a lawyer but I don’t have the money to do that yet. I’m not looking for full legal advice just anyone who has maybe experienced this or can give any advice. Thanks in advance!

    Read the article

  • Reading binary data from serial port using Dejan TComport Delphi component

    - by johnma
    Apologies for this question but I am a bit of a noob with Delphi. I am using Dejan TComport component to get data from a serial port. A box of equipment connected to the port sends about 100 bytes of binary data to the serial port. What I want to do is extract the bytes as numerical values into an array so that I can perform calculations on them. TComport has a method Read(buffer,Count) which reads DATA from input buffer. function Read(var Buffer; Count: Integer): Integer; The help says the Buffer variable must be large enough to hold Count bytes but does not provide any example of how to use this function. I can see that the Count variable holds the number of bytes received but I can't find a way to access the bytes in Buffer. TComport also has a methord Readstr which reads data from input buffer into a STRING variable. function ReadStr(var Str: String; Count: Integer): Integer; Again the Count variable shows the number of bytes received and I can use Memo1.Text:=str to display some information but obviously Memo1 has problems displaying the control characters. I have tried various ways to try and extract the byte data from Str but so far without success. I am sure it must be easy. Here's hoping.

    Read the article

  • How to get local bzr commits to server?

    - by C.W.Holeman II
    lanchpad.net states that for project Emle - Electronic Mathematics Laboratory Equipment 2.0 series is the current focus of development This is what I have done so far: Set the launchpad.net project to import from the sourceforge.net project Emle (this actually set the launchpad.net project to mirror the sourceforge.net project rather than just inport the content once) Examined the launchpad.net project to see that the three commits (#1 - #3) which were done in the sourceorge.net project previousley made it into launchpad.net. Used bzrto get the launchpad.net project which I did while is was still set for mirroring. Made three changes and commits using bzr (#4 - #6). Was unable to see the changes on the launchpad.net site. Requested the mirroring to be stopped (it did). Here is an extract from lanchpad.net for project Emle 2.0 series showing that launchpad.net has #1 - #3: Code for this series The following branch has been registered as the mainline branch for this release series: lp:emle - C.W.Holeman II 3 revisions, 3 in the past month. Here on my system showing changes #1 - #6: $ bzr log --line 6: C.W.Holeman II 2010-02-27 #528096 Corrected setting of paramter value for emleDi... 5: C.W.Holeman II 2010-02-27 Minor refactor - improved comment regarding workaround... 4: C.W.Holeman II 2010-02-27 #529089 #529087 Index file html tag lang attribute cor... 3: cwhii 2010-02-25 {Emle 2.4-5 (BL0011)} New top levels: trunk and tags. 2: cwhii 2010-02-25 New top levels: trunk and tags. 1: cwhii 2010-02-25 New top level trunk and tags. How do I get the changes that are in bzr on my system to apply to launchpad.net?

    Read the article

  • What's it like being a financial programmer?

    - by Mike
    As a student who's done an internship at a Silicon Valley company(non-financial), I'm curious to know what it's like working for a financial company doing software development. I'd expect the hours to be longer, and the pay to be higher. Specifically, I have the following questions: What's the work/life balance really like? Are you expected to work 80 hours a week most weeks? For those who have worked in non-financial software engineering jobs, how does being a financial software engineer compare in terms of work/life balance? How much does it pay? I'm curious as to starting(i.e. just got a BS) pay, as well as "top out" pay. (I'd prefer concrete numbers - ballpark is fine). Also, bonuses would be useful information. What jobs do financial programmers typically have? Are most just general software engineers, or do people typically have very specialized(i.e. AI or systems) backgrounds? Also, do most programmers have PhDs? Are programmers typically required to be at work, or are financial companies generally flexible about letting programmers work from home? When at work, do programmers have to dress formally? What are the technology environments like? Are finance companies using state-of-the-art hardware and software, or are they generally more conservative in upgrading their equipment? What programming languages are typically used? If VBA(shudder) is used, is it a large part of a finance company's workflow? If you could turn back the clock, would you still be a financial programmer? I'm going to keep this post open a little bit longer to get some more responses.

    Read the article

  • Is it possible to run my Windows Form application in Windows CE platform?

    - by Fakhrul
    I am new in Windows CE development and never done it yet. Need some advise from the expert in here. In our current project, we are developing a client-server application. The client side is using a windows form application that are base on Windows XP OS while the server is a web base application. This question are related to the client application (Windows Form). This application are using Sql Server Express Edition for data storage. The data is stored in XML object format. It also can transfer a data from client to server via web service. It also interact with hardware such as Magnetic Stripe Reader, Contactless Smart Card Reader, and a thermal printer. Most of the communication between hardware device and systems are base on Serial Port. It is use standard app.config for the configuration and is a multi threaded application. There is a new requirement to use a Handheld device which is use a Windows CE platform. This handheld included the required equipment such as Contactless Smart Card Reader, Printer and Magnetic Stripe Reader. Instead of developing a new client application, is it possible to me to convert my current application that are base on Windows XP to Windows CE? If yes, how can I do that? If no, is it any other brilliant suggestion to do this? Thanks in advance. Software Engineer

    Read the article

  • jQuery Clone and add row to last row

    - by user198880
    I want to add a row whenever the user click on the new button.I want to clone the row "tRow0" and add it to the last row of the table "tblEquipment tbody".I wrote a JavaScript function for adding the row(AddEquipment).The problem is that the row is not getting added in the last row. clone row : tRow0 last row : tRow1 Actually the new row must added after the "tRow1" row.But the new row get added below "trActivity1_2" row.Please provide me the solution. my javascript function: function AddEquipment() { var row = jQuery('#tRow0').clone(true).show().insertAfter('#tblEquipment tbody>tr:last'); var index = document.getElementById("hdnMaxEqpId").value; jQuery("#tblEquipment tbody>tr:last").attr("id", "tRow" + index) jQuery("td:eq(0) input", row).attr("id", "chkEqp" + index); jQuery("td:eq(1) div:eq(0)", row).attr("id", "divEqpName" + index); jQuery("td:eq(1) input:eq(0)", row).attr("id", "hdnWODefEqpId" + index).attr("name", "hdnWODefEqpId" + index); jQuery("td:eq(1) input:eq(1)", row).attr("id", "hdnEquipmentId" + index).attr("name", "hdnEquipmentId" + index).attr("onpropertychange",""); jQuery("td:eq(1) input:eq(2)", row).attr("id", "txtEquipment" + index).attr("name", "txtEquipment" + index); jQuery("td:eq(1) img", row).attr("id", "imgshowEquipmentTree" + index).attr("onclick", ""); jQuery("td:eq(1) div:eq(1)", row).attr("id", "divEqpImage" + index); jQuery("td:eq(2) div", row).attr("id", "divEqpHierarchy" + index); jQuery("td:eq(3) textarea", row).attr("id", "txtEqRemarks" + index); jQuery("td:eq(4) img", row).attr("id", "imgEqAttachment" + index); } my aspx page: <table id="tblEquipment"> <thead> <tr> <th> </th> <th> Equipment</th> <th> Hierarchy</th> <th> Remarks</th> <th> Attachment</th> <th> Total Cost</th> </tr> </thead> <tbody id="tbEquipment"> <tr id="tRow0" class="trChildItem"> <td> <input id="chkEqp0" name="chkEqp0" type="checkbox" /> </td> <td> <div id="divEqpName0"> <input id="hdnWODefEqpId0" name="hdnWODefEqpId0" type="hidden" value="0" /> <input id="hdnEquipmentId0" name="hdnEquipmentId0" onpropertychange="AutoSaveEquipment(0);" type="hidden" value="0" /> <input id="txtEquipment0" class="clsSpText" name="txtEquipment0" readonly /> </div> <div id="divEqpImage0"> </div> </td> <td> <div id="divEqpHierarchy0"> &nbsp;</div> </td> <td> <textarea id="txtEqRemarks0" class="clsSpTextArea" cols="20" name="txtEqRemarks0" rows="1"></textarea> </td> <td> </td> </tr> <tr id="tActMaster0" class="trInnerChildItem"> <td> </td> <td colspan="5"> <div id="divActivitiesdetails0"> </div> </td> </tr> <tr id="tRow1" class="trChildItem"> <td> <input id="chkEqp1" runat="server" type="checkbox" /> <div id="divEqpEdit1"> </div> </td> <td> <div id="divEqpName1"> <input id="hdnWODefEqpId1" runat="server" type="hidden" value="7" /> <input id="hdnEquipmentId1" runat="server" type="hidden" value="4" /> <div id="divEqp1"> e2</div> <div id="divEqpImage1"> <a id="activiy1" onclick="HideActivities(1)"> </div> </td> <td> <div id="divEqpHierarchy1"> Equipment--&gt;e2</div> </td> <td> <div id="divEqpRemarks1"> Remarks</div> </td> <td> <div> </div> </td> <td> <div> $0.00</div> </td> </tr> <tr id="tActMaster1" class="trInnerChildItem" jquery1275984958765="3"> <td> </td> <td colspan="5"> <div id="divActivitiesdetails1"> <div id="divActivityMaster"> <table> <thead> <tr> <th> <a onclick="ActivityPopUp(0,1)"> </a></th> <th> Activity</th> <th> Description</th> <th> Duration</th> </tr> </thead> <tbody id="tbActivity"> <tr id="trActivity1_1" class="trChildItem" ondblclick="ActivityPopUp(3,1)" onmouseleave="HideActEditDiv('1_1')" onmouseover="ShowActEditDiv('1_1',7,1)"> <td> <div id="divActEdit1_1"> </div> </td> <td> <input id="hdnDefActivityId1_1" runat="server" type="hidden" value="33333" /> <div id="divActivityName1_1"> Act1</div> </td> <td> <div id="divActivityDesc1_1"> Ac1</div> </td> <td> <div id="divActivityDuration1_1"> 1&nbsp;Day</div> </td> </tr> <tr id="trActivity1_2" class="trChildItem" ondblclick="ActivityPopUp(3,1)" onmouseleave="HideActEditDiv('1_2')" onmouseover="ShowActEditDiv('1_2',7,1)"> <td> <div id="divActEdit1_2"> </div> </td> <td> <input id="hdnDefActivityId1_2" runat="server" type="hidden" value="4" /> <div id="divActivityName1_2"> Act2</div> </td> <td> <div id="divActivityDesc1_2"> Act2Desc</div> </td> <td> <div id="divActivityDuration1_2"> 1&nbsp;Day</div> </td> </tr> </tbody> </table> </div> </div> </td> </tr> </tbody> </table>

    Read the article

  • What is optimal hardware configuration for heavy load LAMP application

    - by Piotr Kochanski
    I need to run Linux-Apache-PHP-MySQL application (Moodle e-learning platform) for a large number of concurrent users - I am aiming 5000 users. By concurrent I mean that 5000 people should be able to work with the application at the same time. "Work" means not only do database reads but writes as well. The application is not very typical, since it is doing a lot of inserts/updates on the database, so caching techniques are not helping to much. We are using InnoDB storage engine. In addition application is not written with performance in mind. For instance one Apache thread usually occupies about 30-50 MB of RAM. I would be greatful for information what hardware is needed to build scalable configuration that is able to handle this kind of load. We are using right now two HP DLG 380 with two 4 core processors which are able to handle much lower load (typically 300-500 concurrent users). Is it reasonable to invest in this kind of boxes and build cluster using them or is it better to go with some more high-end hardware? I am particularly curious how many and how powerful servers are needed (number of processors/cores, size of RAM) what network equipment should be used (what kind of switches, network cards) any other hardware, like particular disc storage solutions, etc, that are needed Another thing is how to put together everything, that is what is the most optimal architecture. Clustering with MySQL is rather hard (people are complaining about MySQL Cluster, even here on Stackoverflow).

    Read the article

  • populate FusionCharts with XML data AJAX

    - by Mick
    Hi I have a js file that uses ajax to get a XML doc from a php script . The XML file forms the data to draw a Fusion Chart. I know I am getting the XML data ok but FusionCharts will not draw it . I would really appreciate any help , thanks (FusionCharts.js is included earlier in my script) if(XMLHttpRequestObject) { XMLHttpRequestObject.open("GET", "chart.php?job="+job, true); XMLHttpRequestObject.onreadystatechange = function() { if (XMLHttpRequestObject.readyState == 4 && XMLHttpRequestObject.status == 200) { var xdoc = XMLHttpRequestObject.responseXML; var chart1 = new FusionCharts("Pie3D.swf", "chart1Id", "400", "300", "0", "1"); chart1.setDataXML(xdoc); chart1.render("chart1div"); chart.php produces this XML data <chart caption='ADI Chart Test ' > <set label='Driver' value='12.25' /> <set label='Other Staff' value='223.21' /> <set label='Equipment' value='0.00' /> <set label='Additional Items' value='0.00' /> <set label='Vehicle Fuel' value='0.00' /> <set label='Accomodation' value='0.00' /> <set label='Generator Fuel' value='0.00' /> </chart>

    Read the article

  • How to estimate tomcat server requirements?

    - by Daniil
    We have a brand new webapp written that runs on Tomcat. So far, only one client is using it through the day. They run about 180 unique logins a day. Not really a lot IMO. Now, we managed to sell it to a brand new client who likes and wants to roll it out to 50,000 clients. How many of them will login at the same time - no idea. But I need to do the whole thing - allocate, create, config and maintain. OK - last is simple(errrr). The application runs off of Tomcat 5.5 on Gentoo (I'm thinking to upgrade to Tomcat 6) with MSSQL & mySQL behind. I do realize that a more enterprise ready application would be a better fit, but that's not an option at the moment. Since I've never done this before, I'm a bit lost. Can someone advice on how to go about estimating the equipment requirements for this client? Tomcat does have clustering, so that I can do. MS SQL - I'm sure they have something too. I'm thinking to stick it behind LVS (which we do use at the moment for something else too). Any help from people who deal with these details is greatly appreciated!

    Read the article

  • Adding Mysql Columns in Rails Rake

    - by Gigg
    I have a rake file that does a series of calculations on a database. Basically it adds usage on equipment regularly. At the end of the day it needs to add that days total to a monthly total table and update that same table. i use the following simple concepts: To get data from the database is pretty simple: @usages = Usage.find(:all) time = Time.new for usage in @usages sql = ActiveRecord::Base.connection To insert it into the database: sql.execute "INSERT (or UPDATE) into usages ## add values and options as per MySQL But how do I: take a column from a database, add all of its values together that have a common value in another column, (i.e. if column x == value y) and then insert it into another column in another table, say dailyusages? I have tried these options: task (:monthly => :environment) do @dailyusages = Dailyusage.find(:all) for dailyusage in @dailyusages sql = ActiveRecord::Base.connection time = Time.new device = monthlyusages.device month = time.month if device == dailyusages.device ##&& month == dailyusages.month total = (dailyusage.total.sum.to_i) @monthlyusages = Monthlyusage.find(:all) for monthlyusage in @monthlyusages sql = ActiveRecord::Base.connection old_total = monthlyusage.total.to_i new_total = (old_total + total) sql.execute "UPDATE monthlyusages ( year, month, total, device ) values('#{time.year}', '#{time.month}', '#{total}', '#{dailyusage.device}' )" end I obviously have uncommented options and tried all sorts of things. Any help would really save me a load of trouble. Thanks in advance. (** BTW - I am new to rails, so go easy on me **)

    Read the article

  • XML/RDF to Java Objects with XSD

    - by bmucklow
    So here's the scenario...I have an XSD file describing all the objects that I need. I can create the objects in Java using JAXB no problem. I have an XML/RDF file that I need to parse into those objects. What is the EASIEST way to do this? I have been looking into Jena and have played around with it, but can't see how to easily map the XML/RDF file to the XSD objects that were generated. Here is a snippet of the XSD file as well as the XML/RDF file: <?xml version="1.0" encoding="UTF-8"?> <xs:schema xmlns:xs="http://www.w3.org/2001/XMLSchema" xmlns:a="http://langdale.com.au/2005/Message#" xmlns:sawsdl="http://www.w3.org/ns/sawsdl" targetNamespace="http://iec.ch/TC57/2007/profile#" elementFormDefault="qualified" attributeFormDefault="unqualified" xmlns="http://langdale.com.au/2005/Message#" xmlns:m="http://iec.ch/TC57/2007/profile#"> <xs:annotation/> <xs:element name="Profile" type="m:Profile"/> <xs:complexType name="Profile"> <xs:sequence> <xs:element name="Breaker" type="m:Breaker" minOccurs="0" maxOccurs="unbounded"/> And the XML/RDF: <!-- CIM XML Output For switch783:(295854688) --> <cim:Switch rdf:ID="Switch_295854688"> <cim:IdentifiedObject.mRID>Switch_295854688</cim:IdentifiedObject.mRID> <cim:IdentifiedObject.aliasName>Switch_295854688</cim:IdentifiedObject.aliasName> <cim:ConductingEquipment.phases rdf:resource="http://iec.ch/TC57/2009/CIM-schema-cim14#PhaseCode.ABC" /> <cim:Switch.circuit2>0001406</cim:Switch.circuit2> <cim:Equipment.Line rdf:resource="#Line_0001406" />

    Read the article

  • [C++] Multiple inclusion in multiple files

    - by Amumu
    Hi everyone, I am making a small game. In BattleRecord.h: #ifndef _CHARACTER_H_ #define _CHARACTER_H_ #include "Character.h" #endif class BattleRecord { public: Character Attacker; Character Defender; Status status; int DamageDealt; int GoldEarned; int ExpGained; }; In Character.h: #ifndef _EQUIPMENT_H_ #define _EQUIPMENT_H_ #include "Equipment.h" #endif class BattleRecord; class Character { BattleRecord AttackEnemy(Character &Enemy); } In BattleRecord.h: #ifndef _CHARACTER_H_ #define _CHARACTEr_H_ #include "Character.h" #endif #ifndef _BATLE_RECORD_H_ #define _BATLE_RECORD_H_ #include "BattleRecord.h" #endif class GUI { public: //GUI Methods, and two of these: void ViewStats(Character &Player); void Report(BattleRecord Record) } The problem here is, my Character.h and BattleRecord.h need to include each other, and this definitely will cause multiple redefinition problem. Therefore, I used forward declaration in Character.h by adding: class BattleRecord; The problem is sovled. But then, the GUI.h needs BattleRecord.h again for reporting the battle, so I have to include BattleRecord.h into the GUI.h. I also have to include the Character.h in order to pass into the ViewStat function. I got error and stuck with this up to this piont.

    Read the article

  • What's a good way to provide additional decoration/metadata for Python function parameters?

    - by Will Dean
    We're considering using Python (IronPython, but I don't think that's relevant) to provide a sort of 'macro' support for another application, which controls a piece of equipment. We'd like to write fairly simple functions in Python, which take a few arguments - these would be things like times and temperatures and positions. Different functions would take different arguments, and the main application would contain user interface (something like a property grid) which allows the users to provide values for the Python function arguments. So, for example function1 might take a time and a temperature, and function2 might take a position and a couple of times. We'd like to be able to dynamically build the user interface from the Python code. Things which are easy to do are to find a list of functions in a module, and (using inspect.getargspec) to get a list of arguments to each function. However, just a list of argument names is not really enough - ideally we'd like to be able to include some more information about each argument - for instance, it's 'type' (high-level type - time, temperature, etc, not language-level type), and perhaps a 'friendly name' or description. So, the question is, what are good 'pythonic' ways of adding this sort of information to a function. The two possibilities I have thought of are: Use a strict naming convention for arguments, and then infer stuff about them from their names (fetched using getargspec) Invent our own docstring meta-language (could be little more than CSV) and use the docstring for our metadata. Because Python seems pretty popular for building scripting into large apps, I imagine this is a solved problem with some common conventions, but I haven't been able to find them.

    Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19  | Next Page >