Search Results

Search found 466 results on 19 pages for 'fans'.

Page 15/19 | < Previous Page | 11 12 13 14 15 16 17 18 19  | Next Page >

• Play audio over network with Windows 7?

  - by Josh

  I have a unique situation where I'd like to stream audio (ALL audio, not just mp3s, etc) from my laptop to another computer over the network. I live in a studio apartment and my laptop is my main computer but I'd like it's audio to play on my htpc with a nice stereo system. Since it's a studio, both computers are in the same room so I don't want 2 sets of speakers. I want my computer to directly play back through the stereo. I used to do this with pulseaudio but my job now requires that I run Windows full time. I'm aware of Shoutcast and other similar streaming solutions but I don't want any transcoding done. It's a waste of CPU and not to mention my laptop fans, and I don't mind the network bandwidth that uncompressed audio requires. Is there a way to run Shoutcast without encoding? Also, I know that Windows Remote Desktop can play audio over the network pretty easily. Is this part of .Net that I could just code a simple app that streams the audio without RD'ing in? I also don't want to run it over a physical wire. :)

  Read the article

• AMD FX8350 CPU - CoolerMaster Silencio 650 Case - New Water Cooling System

  - by fat_mike

  Lately after a use of 6 months of my AMD FX8350 CPU I'm experiencing high temperatures and loud noise coming from the CPU fan(I set that in order to keep it cooler). I decided to replace the stock fan with a water cooling system in order to keep my CPU quite and cool and add one or two more case fans too. Here is my case's airflow diagram: http://www.coolermaster.com/microsite/silencio_650/Airflow.html My configuration now is: 2x120mm intake front(stock with case) 1x120mm exhaust rear(stock with case) 1 CPU stock I'm planning to buy Corsair Hydro Series H100i(www.corsair.com/en-us/hydro-series-h100i-extreme-performance-liquid-cpu-cooler) and place the radiator in the front of my case(intake) and add an 120mm bottom intake and/or an 140mm top exhaust fan. My CPU lies near the top of the MO. Is it a good practice to have a water-cooling system that takes air in? As you can see here the front of the case is made of aluminum. Can the fresh air go in? Does it even fit? If not, is it wiser to get Corsair Hydro Series H80i (www.corsair.com/en-us/hydro-series-h80i-high-performance-liquid-cpu-cooler) and place the radiator on top of my case(exhaust) and keep the front 2x120mm stock and add one more as intake on bottom. If you have any other idea let me know. Thank you. EDIT: The CPU fan running ~3000rpm and temp is around 40~43C on idle and save energy. When temp is going over 55C when running multiple programs and servers on localhost(tomcat, wamp) rpm is around 5500 and loud! I'm running Win8.1 CPU not overclocked PS: Due to my reputation i couldn't post the links that was necessary. I will edit ASAP.

  Read the article

• Dell Inspiron 1564 overheating but fan not switching on, how to diagnose?

  - by Smugrik

  I've got a Dell Inspiron 1564 laptop that is about one and a half years old. Since about a week, the laptop started to overheat, causing it to switch off unexpectedly... The cpu fan is working erratically, it can start to spin for a while, doing its job and cooling down the cpu before it stops, but then the temperature goes up, and the fan doesn't reacts, once the temperature reaches a critical point (over 85 celsius, checked with speedfan...), the laptop switches off... I already cleaned the vents and fan from dust, to no avail, and it was actually quite clean anyway. Drivers and bios are up-to-date, no crapware was ever installed on this machine. I don't know how to diagnose the problem, could it be the temperature sensors that sends wrong information, so the fan doesn't reacts? but then I believe the computer wouldn't detect the overheat and stop... Is there a way I can pin point the problem? Maybe some low-level diagnostic tools to check functionality of sensors and fans??? The warranty is already over so any suggestion would be welcome. Thanks!!

  Read the article

• Laptop GPU apparently blew up, motherboard doesn't even turn on its power LED. [But..]

  - by leladax

  EDIT: (Was: Laptop automatic shutdown after 2 seconds) If I take out the GPU, the motherboard LED turns on but then [if it attempts to power up and boot] it turns off after 2 seconds [fans turn on normally in that short period]. [Without the GPUs out there's not even an attempt to boot.] It's an SLI motherboard for a toshiba (model X200-219). If I take out one of the GPUs (they are on top of each other) it surprisingly lets the motherboard turn on too (as it is if both are out) but it still turns off after 2-3 seconds, same behavior. I wonder if it's the GPU that produces the 'turn off after being on' behavior and not something else. [Has anyone seen this behavior with blown up GPUs or could it be something else?] Previous question (before EDIT. Sorry, but someone thought it productive to lock the other one as duplicate): I'm trying to insvestigate which component produces this behavior. Other indications show it may be the GPU but I wonder if anyone knows more. It's a Toshiba Satellite X200 description: AC power shows the power being fed normally, when turned on the fan works and it appears to be starting up but after 2 seconds it shuts down with only the 'AC power connected" led on. -- seconds are about up to 4,maybe not 2 exactly.

  Read the article

• New Computer won't boot up

  - by Reggie

  I brought new components and put a computer together. I installed win7(32bit) and everything was working as it should. However my case came with two USB3 front ports I could not connect because of motherboard did not support USB3, so I swapped out the board for a new motherboad with USB3 connection. Now I put everything back together but it won't bootup. "Memory Ok" light stay on. Motherboad LED is on. There is power, all fans are on but I got no display. There is no activity in back of the systems, none of the peripheral connection in the back are working. I have tried the following but to no avail. Reboot multiple times Unplug power and plug the power back Reset the CMOS battery..let it stays out for 10 minutes or more. Unplug all peripheral device but no luck Reset memory..... nothing happen The only thing I did not do was remove the cpu...but I unplug everything else. Please help, thank you.

  Read the article

• Chipset fan on the frtiz - compressed air hasn't fixed anything - is there anything I can do?

  - by Anthony

  Yesterday, my computer started to make an annoying whining noise. Knowing that this is likely a fan issue, I opened the case and proceeded to determine which fan was causing the issue. I got some compressed air and tried cleaning out the dust around it (and the rest of the computer while I was at it). This hasn't seemed to fix the issue. Now, if it were just any fan, I would probably just replace the fan - they're relatively cheap after all. However, this is a special fan. Aside: For what its worth, I feel bad that the graphics card blocks part of the fan, but it is the only slot the graphics card fits, so I had no choice. After pulling out my motherboard user guide, it looks like this is a fan placed directly on top of the chipset. To be perfectly honest, I have no clue what the purpose of the chipset is - but it sounds important. After some quick research, I see that it is responsible for providing the bridge between my CPU, RAM and graphics, among other things. Just a quick search at Newegg tells me that chipset fans can be purchased at pretty reasonable prices (< 20 dollars). Is it practical to replace this fan? It is an old computer as computers go and I wouldn't be terribly upset to upgrade the motherboard and processor, so perhaps this is a sign. Hardware Specs: Motherboard: Asus A8N-E Chipset: NVIDIA nForce4 Ultra

  Read the article

• i7 overclocking problem

  - by benwebdev

  Hi everyone, I've got an overclocked system that seems to be misbehaving. When trying to boot up from cold the system just hangs and nothing is output to the screen. Fans are on as they should but nothing happens to finish the boot. From here I have to switch it off then on again and the boot completes. If I go into the tweak menu in the BIOS I'm informed that a boot has failed I've been in touch with Overclockers UK support a bit and theres not yet been a solution. We've mainly been tweaking the voltage for the CPU. Any suggestions? I'm new to Overclocking which is why I got a bundle with OCUK. With this issue happening on Cold Boot too its tricky to test as I have to make a change then wait till the next day. My system is here: Intel Core i7 930 2.80Ghz overclocked to 4GHz Gigabyte X58A-UD3R (BIOS Version: FC) 6GB RAM Power Supply - CoolerMaster Silent Pro M series 700W One suggestion made by OCUK was that maybe its the power supply but I'm not sure and dont have a spare - it's brand new and a pretty expensive piece of kit. Any thoughts on this? Other recomendations for Power? thanks Ben

  Read the article

• Does AMD Cool n Quiet Slow Down Your System?

  - by Software Monkey

  I discovered today that having AMD Cool n Quiet enabled in my BIOS appears to be slowing down my Windows XP SP2 system by about 29% on memory & CPU intensive workloads. I was wondering if (a) anyone else had encountered this, (b) anyone can offer an explanation, (c) there are any negatives I need to be aware of if I keep AMD CnQ disabled. With some superficial testing so far, I don't immediately notice any difference with CnQ off (other than the performance being what I expected from this new hardware). It seems to ramp up the CPU fan a little bit as my program maxes out 1 core, but that's the same as with CnQ on. And when I let the system idle the CPU fan slows down and the systems as quiet as a mouse (after years of 6 small fans churning like they want to go into orbit it's nice to again have a system where I can hear the HDDs seeking). Bonus question: Does CnQ cause issues with system stability? I ask because the reason I disabled it was because I have had a few freezes and 1 spontaneous reboot with my new hardware.

  Read the article

• Macs don't connect to wifi access point but PCs will

  - by Josh

  So, as a side project I'm going to try and figure out why the wifi APs in my building exhibit the following behavior: - They typically allow all types of computers to connect without issues - Sometimes Apples can't get an IP address but will still connect to the AP's signal - Less often, PCs can't connect to the wifi (same as above - yes signal, no IP addy) - Don't let Raiders fans on no matter the time of day! My first thought was that the DHCP leases were all taken up when the Apples would try to connect, and it was just their unlucky timing, but I would then try to log on with a PC that had a new, unleased MAC address and it would work... Could this be something to do with interoperability between an apple wifi card, and the APs? Different parts of the DHCP lease being taken up first? The fact that the Seattle Mariners might actually be good this year?? If this hasn't used up everyone's patience (with my crappy sports jokes), something else I could use some help with: - We don't have the model or type of AP - This is because there is no documentation available for them, and they literally look like small white boxes with no writing on them. Also, the company that installed them is out of business, so the situation might be that no docs will ever be on the way. -- Do you guys have any ideas on how to figure out what we have? Thanks as always for all the help, and I'm looking forward to the day when I know enough to start contributing back to the site, Josh

  Read the article

• Mac OS Leopard: SyncServer process constantly using 100% CPU

  - by macca1

  I am running Leopard that I upgraded from Tiger. I've been noticing that every once in a while the SyncServer process starts up and eats up all the CPU. The fans will start going at full blast and the laptop will slow down to a crawl. I need to force quit the process from Activity Monitor to get it under control. It disappears for a while, but eventually gets started again. I do have an iphone as well that I sync so I'm wondering if syncServer might be an apple process checking for my phone plugged in. Edit: Tried iSync and the manual resetsync as suggested, but got this output: Vince-2:~ vince$ /System/Library/Frameworks/SyncServices.framework/Versions/A/Resources/resetsync.pl full 2010-03-12 08:03:50.230 perl[176:10b] SyncServer is unavailable: exception when connecting: connection timeout: did not receive reply PerlObjCBridge: NSException raised while sending reallyResetSyncData to NSObject object name: "ISyncServerUnavailableException" reason: "Can't connect to the sync server: NSPortTimeoutException: connection timeout: did not receive reply ((null))" userInfo: "" location: "/System/Library/Frameworks/SyncServices.framework/Versions/A/Resources/resetsync.pl line 16" ** PerlObjCBridge: dying due to NSException Vince-2:~ vince$ And during that syncServer started spinning up 95-100% just like it always does.

  Read the article

• BIOS unable to boot CD or Hard Drive

  - by Gabriel

  Motherboard Intel DQ35MP. HDD Caviar Green 1TB. I'm having problems with my BIOS and/or hard drive/disc drive. Came back from a trip, booted my computer, and realized that the BIOS wasn't booting anymore, just a black screen with no beep sounds. Only fans and lights on. Then I thought it might be caused by the video card, I removed it, and still no BIOS screen. Then I removed the hard drive and voila BIOS screen is back again. If the hard drive is defective then I can check that with a Rescue Disk. I inserted the CD on the Disc Tray but the computer did not respond to it, the screen freezes in black with an "E7" string at the bottom right corner just after the BIOS screen, this happens with or without discs. BIOS settings are set to default, and CD reading is on top of the boot device list. EDIT I removed the BIOS battery, rebooted the CPU, the BIOS screen showed up, and then it freezed in E7. Placed the BIOS batttery, rebooted and same thing, we are stuck with the E7 string. I uploaded a video to illustrate the problem http://www.youtube.com/watch?v=13jPdBcIrBU

  Read the article

• GA 8KNXP Rev1.0: 4 GB installed, only 3.5 GB recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4 GB. The specification from the manual says: Maximum memory support: 4 GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my Linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in Linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• No video signal and server shuts down

  - by Ilya

  I have a brand new server. The motherboard is Intel S2600CP4, two 8-core Intel E5-2600 processors. RAM is 8 DIMM slots of 8 GB each (KVR1600D3D4R11SK4/32GI, I installed them into the blue slots), Power supply is 1050W Corsair. Most of the time the server won't start up - the fans are spinning, but I don't have video signal. And it keeps restarting on its own every 3 mins. But maybe after 30 mins it will eventually load and show something on the screen. I even was able to install ESXi 5.0 (vSphere) on it. It recognizes both CPUs and all of the 64GB of RAM. But even then it worked only for around 5 hours and then restarted on its own. What's the problem? That's a very expensive peace of hardware and I can't afford purchasing a new motherboard/CPU. By the way, on the front panel the "System Status" LED is constantly amber (not blinking), even when the server started successfully. And also in the BIOS I can see lots of "processor 01 unable to apply microcode update 8160" fatal errors. Please help me with issue, I will really appreciate this!

  Read the article

• What parts of a motherboard age, and how can I choose one with the longest possible life?

  - by Robert Harvey

  I have a home-built computer that's probably about four years old. I realize this probably seems ancient to some folks, but computers have no moving parts (except the fans), so theoretically they should last a long time, if I still have software to run on them. A few weeks ago, it began blue-screening and freezing up, with various error messages. It almost always happened about five minutes after startup. I assumed that the video card was overheating, since the cheap little fan on the heatsink died, so I replaced it. Long story short, after upgrading the video drivers a couple of times and performing some other troubleshooting, I remembered that the last time this happened, I took out the memory SIMS and cleaned the contacts with a gum eraser, so I did that again (noting that the SATA cables were very close to the chips on the SIMS). I re-routed the cables and reinstalled the SIMS. So far, so good; the machine has been trouble-free since. But blue-screens are distressing; I never know what bits are being chewed up in my OS installation when something like this happens. So I'm wondering if I'm choosing my components properly. If it matters, it's an Intel D915GAG motherboard and Corsair memory, but what I'm wondering is, should I be looking for certain characteristics when I choose these parts for my next computer, so that I can avoid this problem in my next build?

  Read the article

• GA 8KNXP Rev1.0: 4GB installed, only 3.5 recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4GB. The specs from the manual say: Maximum memory support: 4GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Any ideas? Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp2 KB896256 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• My PC is powercycling, what's going wrong?

  - by Renai

  So here is my sorry story of woe. My PC has been functioning normally for some time. Last week I bought a cheapish powered USB hub and plugged it into my home PC, which runs Windows 7. This weekend I plugged that hub into my home PC. At some stage I hibernated the PC. Then later on I plugged my Kobo eReader into the hub to charge. Later on I started the PC up. Only thing is, it now won’t start up. It just powercycles on for a second and a half with the fans at full, then powercycles off. Then back on for two seconds, then back off. There’s no display at all and it won’t get to the BIOS screen. It looks like anything USB is not functioning — the keyboard and mouse are not lighting up etc. I’ve taken out the BIOS battery and reseated the RAM, reseated the graphics card and so on, but my suspicion is that I have blown the USB section of the motherboard somehow. Suggestions? All else failing, where is the best place to take this machine in Sydney to get evaluated? It’s a fairly powerful beast, all up has cost me about $2500 over the years, including upgrades and a recent new graphics card, so can’t just start from scratch.

  Read the article

• Computer sending data while turned off

  - by Nicklas Ansman

  I have a some what strange problem (which could have and easy and obvious solution for all I know). My problem is that when I've booted ubuntu (now 10.4 but same problem with 9.10) and turns it off it starts sending a HUGE amount of data via the ethernet cable, so much in fact that my router can't handle it and stops responding. As far as I can tell the computer is completely turned off with no fans spinning. I can add that if I boot windows I do not have this problem, just when exiting ubuntu. There are two "fixes" for my problem: Pull the ethernet cable until the next boot Turn off power to the PSU and wait for the capacitors to unload Is there anyone who knows what could be going on? I'd be happy to post some logs or conf-files. Currently I'm using the ethernet port on my motherboard which is a Asus P6T Deluxe V2 with an updated version of the BIOS (maybe not the latest but since it only happens when I've been in ubuntu I don't wanna mess with the BIOS too much). Regards Nicklas ---------Update 1---------- The router is a D-Link DIR 655 with the latest firmware. ---------Update 2---------- I've now reinstalled ubuntu (with 10.4) and I still experience the same problem.

  Read the article

• Five stars of open data - example and review

  - by Joe

  (there may be a more suited SE site for this question so feel free to shift) I have some data I'd like to make open to the public - It's synatesis of some related data retrived from freedom of infomation requests over the last year. The data itself is at http://www.cs.rhul.ac.uk/home/joseph/domesday/Domesday-Scotland.csv or for fans of Excel, at http://www.cs.rhul.ac.uk/home/joseph/domesday/Domesday-Scotland.xlsx . It's no more than a table with about five columns. I'd like to make this properly open data, so I was looking at the 5 star deployment scheme for Open Data. Much of which is fine but I'm confused towards the end and I could do with an explenation from people who know the answers. So to get achieve the star levels I need: "make your stuff available on the Web (whatever format) under an open license" trival - all I have to do is put the notes up on the page that will give the provance of the data. "make it available as structured data (e.g., Excel instead of image scan of a table)"… done… "use non-proprietary formats (e.g., CSV instead of Excel)" - done… "use URIs to identify things, so that people can point at your stuff" - this is where I start to get a bit hazy - does this mean there should be an URI for every line in the table? "link your data to other data to provide context" - this isn't massively clear to me - does this mean to give the provence of the data? One column of the data I've put out is a link to where the data came from - is that the sort of thing we're looking at? Any and all information and answers welcome… EDIT - or if anyone wants to recommend a place SE or other place to ask the question - that would be cool...

  Read the article

• UPS power requirements for server

  - by captainentropy

  Greetings! So, I just placed an order for a new server. The company recommended that I get a 3000W UPS. (!) As best as I could I calculated the following wattage consumption based on benchmarked data or datasheets provided by the manufacturers of each component: number watts **total watts** MoBo 1 240 240 CPUs (E5540) 2 80 160 RAID cards (3ware) 2 18 36 RAM (6x4GB) 6 3 18 DVD drive 1 7 7 floppy 1 2 2 RE4 drives 8 7 56 WD20 drives 8 6 48 Intel X25 SSD 2 0.15 0.3 total = 567 So that is for the PSU requirements only. The PSUs in the machine are a 720W for the master node and 800W each for two subsystems. That's a total of 2320W that can be delivered by these PSUs. But that is 4X the amount being consumed, at most, by the components. I didn't count case fans or the eSATA card (3W maybe?) or what the PSUs themselves require but assuming I double or triple my calculations I'm not even remotely close to the 3000W UPS I was suggested to get. They run at least $1100. I could get a 2000W for about $750 or a 1500W for $450 and still be well over my estimated power need. I don't think I need a whole lot of run time in the case of a power outage, maybe 20 minutes max, enough time to shutdown if the power doesn't come on within 5-10 minutes. Any thoughts? Am I off on my calculations? Did I overlook something major? If so what are your suggestions for a UPS? Thanks!

  Read the article

• Laptop Randomly Turning On and Off

  - by Ian Mallett

  So, I have a pretty new laptop, and one of its quirks is that, at random times (though typically in the middle of the night), it seems to wake up from sleep mode, churn a bit, and then go back into sleep mode. I write "seems" because its fans are very loud, so it's obvious when it's not asleep, but during the time it is "on", I can't see anything on the screen. I have researched the problem somewhat, and could only find similar issues; nothing identical. In those cases, it appeared that certain devices could be responsible. Nothing is plugged into my computer during this behavior, but I nonetheless disabled every device's permission to wake the computer through the device manager. This included disabling the magic packet wake for the network (despite its only having a wireless connection). Using "powercfg /lastwake" gives an empty wake history. But, I also went through all the tasks and checked if they would wake the computer. None appeared to. The problem persisted, so, after some more research, I found this, and executed it for all power schemes on the computer. The problem persists. System: OS: Windows 7 Professional CPU: Intel 990X GPU: NVIDIA GeForce 580M/12GB RAM Motherboard: Clevo X7200 Model: NP7282-S1 (Sager-built laptop)

  Read the article

• Computer sponteously reboots when doing heavy file copy to/from disk

  - by Mark Hosang

  I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. Update: I left the desktop off for a few days and it started. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Update: I always keep the desktop running and I never shut it down. During updates or manual restarts, it powers up without issues. I wonder if this sheds lights on the issue. Any idea how I can narrow down the issue? ex: if I can find if the PSU is dying etc. I'd really like to fix the issue. Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp3 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• Dell PowerEdge 860 won't boot but gets power

  - by fierflash

  I have a Dell PowerEdge 860. Got an 2008 R2 running on it. Here is the scenario I'm currently in: I can boot it up and work as usuall. But when I restart it, it just shuts down, doesn't reboot, and it won't boot up again. Then it stays in this "mode", On/off button blinking green(standby mode?) and System Indicator LED blinking amber. If I try to press the On/Off button on the frontpanel it won't boot. It's like you can hear the fan from the PSU running but nothing else is trying to boot. If I unplug the powercable and then put it back in again it's the same, the extremley noisy fans won't start and it's just sitting there. If I let it "rest" for like 1 to 24 hours while the powercable is unplugged and I plug it in again, it boots directly, without me having to push the On/Off button. What I have tried: Run diagnostics(not the one in POST phase) and everything is fine Booting without any cables except the powercable Boot without memory installed Boot without the raidcable plugged in Cleared NVRAM Reseated all the components and cables Googling like a freak for any possible solution Tried Dell Support but I don't have any warranty left so they can't help me unless i pay some ridiculous amount of money I suppos Do anyone have some experience with the same issue? Do I need to replace something or is there any other way to determine the problem? Any help will be greatly appreciated.

  Read the article

• Turn computer into DAS (Direct Attached Storage)

  - by Damon

  Can we build a direct attached storage by taking a computer/server, adding an HBA, and installing some appropriate software? We would use Debian as a host OS for both the DAS and the server. If so, what software do we use? And do we simply need a HBA for the DAS and the Server? Or do we need more hardware? The goal is to use an older server that does not have enough room for drives but does have ECC memory, server processors, redundant power supplies, dual nics, etc. Then find any boxes, server or not, the key being having enough room for 8-12 drives, fans, etc. and turning them into a DAS; build two of these DAS's and have them connected to the server. Eventually we want to have two servers using DRBD and associated services like heartbeat and pace maker to create an HA setup for our server(s) but that will take a long time to configure since I have no experience with anything related to DRBD (yet) and have a learning curve I have to get past, not to mention the additional cost of more hardware (two servers vs one).

  Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19  | Next Page >