Search Results

Search found 419 results on 17 pages for 'irq'.

Page 15/17 | < Previous Page | 11 12 13 14 15 16 17  | Next Page >

  • Asus K50I sound issues

    - by MrStatic
    I have an Asus K50IJ (Bestbuy) laptop and have issues with my sound. Speakers themselves work fine but when I plug into the headphone jack it auto mutes the front channel and no sounds comes out of either the speakers or the headphones. If I then unmute the channel I get sound from both the speakers and the headphones. alsamixer shows the Headphone channel as all grayed out. /etc/modprobe.d/alsa-base.conf I have tried snd-hda-intel model="asus-laptop" and snd-hda-intel model="asus" In Sound Preferences I have gone to output and changed the Connector to 'Analog Headphones' that results in no sound from either speakers or headphones. As one forum suggested I tried to comment out blacklist snd_pcsp in the blacklist.conf which resulted in no change. lspci -v shows: 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) Subsystem: Santa Cruz Operation Device 1043 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at fe9f4000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel

    Read the article

  • DPMS does not work: the monitor is not switched off

    - by bortzmeyer
    I have a monitor which was properly switched off by my Debian PC when unused. I attached it to another machine and, this times, it is never switched off. In /etc/X11/xorg.conf, I have: Section "Monitor" Identifier "Generic Monitor" Option "DPMS" It is recognized when X11 starts: (II) Loading extension DPMS ... (II) VESA(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display ... (**) Option "dpms" (**) VESA(0): DPMS enabled The operating system is Debian stable "lenny". The graphics card is: 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrate d Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device 2a6f Flags: bus master, fast devsel, latency 0, IRQ 5 Memory at fe900000 (32-bit, non-prefetchable) [size=512K] I/O ports at b080 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fe800000 (32-bit, non-prefetchable) [size=1M] Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-Capabilities: [d0] Power Management version 2 X11 is: X.Org X Server 1.4.2 Release Date: 11 June 2008 X Protocol Version 11, Revision 0 Build Operating System: Linux Debian (xorg-server 2:1.4.2-10.lenny2) Current Operating System: Linux ludwigVII 2.6.26-2-686 #1 SMP Sun Jun 21 04:57:3 8 UTC 2009 i686 Build Date: 08 June 2009 09:12:57AM

    Read the article

  • Having munin server monitoring problem: Graphs not being generated.

    - by geerlingguy
    When I run munin-cron (munin-cron --debug), I get the following error: 2010/05/10 13:39:01 [WARNING] Call to accept timed out. Remaining workers: archstl.org;archstl.archstl.org 2010/05/10 13:39:01 [DEBUG] Active workers: 1/8 These errors simply keep repeating themselves until I quit munin-cron. I've followed the directions for debugging munin on the 'Debugging Munin plugins' wiki page, but I get the following results when going through their directions: After telnetting to localhost 4949, I can see a list of plugins, see a node at archstl.archstl.org, but can't fetch anything. The output is as follows: >fetch cpu . However, on the same machine (which is both the node and the master munin server), I can run munin-run cpu, and it prints the results correctly to the command line, like so: user.value 100829130 nice.value 3479880 system.value 13969362 idle.value 664312639 iowait.value 12180168 irq.value 14242 softirq.value 199526 steal.value 0 Looking at the wiki page mentioned above, it looks like it might be a plugin environment problem, but I can't figure out how to fix/change this... If the plugin does run with munin-run but not through telnet, you probably have a PATH problem. Tip: Set env.PATH for the plugin in the plugin's environment file.

    Read the article

  • Ubuntu xrandr rotate issue

    - by user83544
    I've just bought a second monitor for my PC which happens to be a pivot monitor. I've already read lots of forums related to my problem but haven't come across a solution - I have the same symptoms as dozens of posts but no matter whatever I try it just doesn't work. I've already changed the xorg.conf file and added in the device section just under Driver "nvidia" the following for my second monitor: Option "RandRRotation" "on" When I save and reboot I try to rotate my screen with the nvidia X server settings by choosing the second monitor and clicking either "left" or "right" for the rotation. It immediately exits the nvidia settings window and does nothing. I tried within the terminal by typing: xrandr -o right I get the following error: X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 154 (RANDR) Minor opcode of failed request: 2 (RRSetScreenConfig) Serial number of failed request: 14 Current serial number in output stream: 14 I actually manage to rotate it with Option "Rotate" "CCW" instead of "RandRRotation". The problem with this solution is that you get the second monitor in the right position, but any window you open on that screen is practically unchangeable. You can't change the size nor move it, making it useless for reading PDFs, which is the main reason why I bought this second screen to help me write my thesis. Any help is really appreciated. sudo lshw -c video hiram@hiram-linux:~$ sudo lshw -c video *-display description: VGA compatible controller product: nVidia Corporation vendor: nVidia Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:16 memory:f8000000-f9ffffff memory:d8000000-dfffffff memory:d4000000-d7ffffff ioport:dc00(size=12 memory:fbd80000-fbdfffff

    Read the article

  • "Can't find root filesystem / error mounting /dev/root" when booting to new kernel

    - by salparadise
    I am trying to upgrade my kernel from 2.6.18-274 to 2.6.39 for some wireless card drivers. When I boot into the new kernel I get the "Can't find root filesystem / error mounting /dev/root" googling led me to this page http://fedoraproject.org/wiki/Common_kernel_problems#Can.27t_find_root_filesystem_.2F_error_mounting_.2Fdev.2Froot From what I am reading seems to be an issue with a driver for my SATA controller or HD, but I can't find what option I need to add to the kernel. Doing a diff from the old initrd to the new one gives me the following: root-> diff /tmp/kafter /tmp/kbefore 6a7,8 > lib/dm-message.ko > lib/dm-region_hash.ko 8a11 > lib/dm-raid45.ko 13d15 < lib/dm-region-hash.ko 16a19 > lib/dm-mem-cache.ko Do I need any of those? not sure if I would need dm-raid45.ko as I am not running a raid. I have the same SATA and IDE options configured for both kernels so not sure what else to look for, any help is appreciated. Additionally here is the HW info: 00:1f.2 IDE interface: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Controller (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Hewlett-Packard Company Unknown device 3006 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 233 I/O ports at 1818 [size=8] I/O ports at 1830 [size=4] I/O ports at 1820 [size=8] I/O ports at 1834 [size=4] I/O ports at 14f0 [size=16] Capabilities: [70] Power Management version 2 root-> smartctl -a /dev/sda ... === START OF INFORMATION SECTION === Device Model: WDC WD5000AADS-00S9B0

    Read the article

  • fglrx-legacy-driver not seeing Radeon HD 4650 AGP

    - by Rocket Hazmat
    I am running Debian Squeeze on an old Dell Dimension 8300 box. It has an AGP Radeon HD 4650 card. I use this machine to mine bitcoins, and today I noticed that the machine had rebooted! My precious uptime! Anyway, my miner wouldn't start, so I figured might as well update my graphics driver, maybe that would fix the issue. I went to amd.com and downloaded the newest driver (12.6 legacy), but after installing it, aticonfig gave an error: aticonfig: No supported adapters detected I uninstalled the driver and figured I'd try to install it from apt. AMD has dropped support for the HD 4000 series in fglrx, forcing me to use fglrx-legacy-driver (currently only in experimental). In order to install this, I had to update libc6 (and some other important packages, like gcc), I had to use their wheezy versions. I finally got fglrx-legacy-driver installed, but I still got: aticonfig: No supported adapters detected Why isn't the driver finding my video card? I have a hunch it has something to do with the fact that it's an AGP video card. Here is the output of lspci -v (why does it say Kernel driver in use: fglrx_pci?): 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] nee ATI Device 0028 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e0000000 (32-bit, prefetchable) [size=256M] I/O ports at de00 [size=256] Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Capabilities: [58] AGP version 3.0 Kernel driver in use: fglrx_pci EDIT: fglrx 12.4 seems to work. Thing is, since I am on kernel 3.2, I need to apply this patch to common/lib/modules/fglrx/build_mod/firegl_public.c. I thought ATI dropped support for the 4xxx series after 12.4. Why doesn't 12.6 legacy work?

    Read the article

  • EC2 AMI won't boot after edit

    - by Eric Lars0n
    I did something stupid, I got a new laptop and copied everything over to the new one, then wiped the old one clean. Then I realized that I forgot to copy the private key out of .ssh that I use to connect to my AWS EBS backed instance. So I can't log in to my custom AMI. So I created a new Volume from the Snapshot of the AMI, then started up a public instance and attached the Volume to it, edit the sshd_config to allow for password log in. Unmounted the volume, detached it, made a snapshot of it, then made a new AMI from the snapshot. The new AMI launches, but never passes the Status Checks and is not reachable. What am I doing wrong? Or alternatively how can I fix my problem? Edit: Adding some of the console output Linux version 2.6.16-xenU ([email protected]) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 SMP Mon May 28 03:41:49 SAST 2007 BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000006a400000 (usable) 980MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active IRQ lockup detection disabled RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize NET: Registered protocol family 2 Registering block device major 8 XENBUS: Timeout connecting to devices! Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,0)

    Read the article

  • Backtrack, Wi-Fi not working

    - by hradecek
    I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

    Read the article

  • cset shield --kthread on: should I use this?

    - by lori
    I'm reading up on cpu shielding using Alex Tsariounov's cset utility here: https://rt.wiki.kernel.org/index.php/Cpuset_Management_Utility/tutorial In the tutorial I'm finding the wording around migrating kernel threads from having access to all cpus to running only in a certain cpuset a bit ambiguous The tutorial says the following: Some kernel threads can be moved into the unshielded system cpuset as well. These are the threads that are not bound to specific CPUs. If a kernel thread is bound to a specific CPU, then it is generally not a good idea to move that thread to the system set because at worst it may hang the system and at best it will slow the system down significantly. These threads are usually the IRQ threads on a real time Linux kernel, for example, and you may want to not move these kernel threads into system. If you leave them in the root cpuset, then they will have access to all CPUs. The tutorial then goes on to say: However, if your application demands an even "quieter" shield, then you can move all movable kernel threads into the unshielded system set with the following command. [zuul:cpuset-trunk]# cset shield -k on cset: --> activating kthread shielding cset: kthread shield activated, moving 70 tasks into system cpuset... [==================================================]% cset: done I am confused by this final sentence. By using the word however, it seems to suggest that you typically should not move the movable kernel threads into the unshielded system set. Is this the case, or is it safe to move kernel threads which can be moved into a cpuset, thereby preventing them from running on some cpus?

    Read the article

  • Tuning Linux + HAProxy

    - by react
    I'm currently rolling out HAProxy on Centos 6 which will send requests to some Apache HTTPD servers and I'm having issues with performance. I've spent the last couple of days googling and still can't seem to get past 10k/sec connections consistently when benchmarking (sometimes I do get 30k/sec though). I've pinned the IRQ's of the TX/RX queues for both the internal and external NICS to separate CPU cores and made sure HAProxy is pinned to it's own core. I've also made the following adjustments to sysctl.conf: # Max open file descriptors fs.file-max = 331287 # TCP Tuning net.ipv4.tcp_tw_reuse = 1 net.ipv4.ip_local_port_range = 1024 65023 net.ipv4.tcp_max_syn_backlog = 10240 net.ipv4.tcp_max_tw_buckets = 400000 net.ipv4.tcp_max_orphans = 60000 net.ipv4.tcp_synack_retries = 3 net.core.somaxconn = 40000 net.ipv4.tcp_rmem = 4096 8192 16384 net.ipv4.tcp_wmem = 4096 8192 16384 net.ipv4.tcp_mem = 65536 98304 131072 net.core.netdev_max_backlog = 40000 net.ipv4.tcp_tw_reuse = 1 If I use AB to hit the a webserver directly I easily get 30k/s connections. If I stop the webservers and use AB to hit HAProxy then I get 30k/s connections but obviously it's useless. I've also disabled iptables for now since I read that nf_conntrack can slow everything down, no change. I've also disabled the irqbalance service. The fact that I can hit each individual device with 30k/s makes me believe the tuning of the servers is OK and that it must be some HAProxy config? Here's the config which I've built from reading tuning articles, etc http://pastebin.com/zsCyAtgU The server is a dual Xeon CPU E5-2620 (6 cores) with 32GB of RAM. Running Centos 6.2 x64. The private and public interfaces are on separate NICS. Anyone have any ideas? Thanks.

    Read the article

  • Sound doesn't work anymore after replacing RAM

    - by thejh
    Hello, today, I replaced one old RAM module with two newer, bigger ones, but now, the sound doesn't seem to work anymore. Already ran alsaconf and it didn't help. Output of lspci for the audio device: 00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1) Subsystem: Giga-byte Technology Device a002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel The audio device is onboard and has six configurable outputs, two or so are also capable of being an input (if I remember it correctly), but I don't know how to control it under linux. Does somebody know how/whether replacing the RAM could be related to my problem and/or how to fix it?

    Read the article

  • LMDE detects a wireless card, but can't use it

    - by Davidos
    LMDE can see my wireless card, and correctly identifies it, but it refuses to let me turn it on through the shiny graphical interface. Is there a way to use the non-shiny terminal to turn on my wireless? One small tidbit I noticed was the stated version; it says the version is 00. I believe that's hexadecimal for 0, which may indicate something screwy with the software. It would be nice if someone could tell me how to figure out how to solve this kind of problem in the future. *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 00 serial: 91:e3:7b:0d:a3:a9 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-1-amd64 firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:e1d00000-e1d01fff I've tested multiple other network managers, and none of them work. W ireless switch is on, I'm sure it's a driver problem.

    Read the article

  • fglrx-legacy-driver not seeing Radeon HD 4650 AGP

    - by Rocket Hazmat
    I am running Debian Squeeze on an old Dell Dimension 8300 box. It has an AGP Radeon HD 4650 card. I use this machine to mine bitcoins, and today I noticed that the machine had rebooted! My precious uptime! Anyway, my miner wouldn't start, so I figured might as well update my graphics driver, maybe that would fix the issue. I went to amd.com and downloaded the newest driver (12.6 legacy), but after installing it, aticonfig gave an error: aticonfig: No supported adapters detected I uninstalled the driver and figured I'd try to install it from apt. AMD has dropped support for the HD 4000 series in fglrx, forcing me to use fglrx-legacy-driver (currently only in experimental). In order to install this, I had to update libc6 (and some other important packages, like gcc), I had to use their wheezy versions. I finally got glrx-legacy-driver installed, but I still got: aticonfig: No supported adapters detected Why isn't the driver finding my video card? I have a hunch it has something to do with the fact that it's an AGP video card. Here is the output of lspci -v (why does it say Kernel driver in use: fglrx_pci?): 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] nee ATI Device 0028 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e0000000 (32-bit, prefetchable) [size=256M] I/O ports at de00 [size=256] Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Capabilities: [58] AGP version 3.0 Kernel driver in use: fglrx_pci

    Read the article

  • Why would my network slow down?

    - by monkthemighty
    The network at my work has about 40 computers on it and a quite a few printers. When there are a lot of people working the network will be slow. I can test the ping between my computer and the router and it will keep rising, sometimes to the point that it times out. The router we are using is running Ubuntu on a atom processor and it has 4gb of ram. When the network slows the process Ksoftirq will be using most if not all of the processing power. I have found that Ksoftirq is a process that handles irq requests. Also when the network slows down I have captured packets from the router and using tshark and looked at it using wireshark on my laptop. With the capture show a lot of packets with TCP Dup ACK and TCP Retransmissions. The destinations of the TCP Dup and TCP retransmissions are to most of the computers on the network but there are some that are far more than others. What could this problem be caused by?

    Read the article

  • Kernel oops on Linux running in VirtualBox breaks some IO-related functionality on the server

    - by Kristoffer E
    We are having problems with CentOS release 6.3 running in VirtualBox on Windows 7 machines. The symptoms are the following: Everything works as normal for several hours, even days. Then something happens which breaks the system. What we still can do after this something happens: Access the web server Use existing SSH sessions to run top and free What does not work: Starting new SSH sessions (hangs after username and password is entered) Running ls in existing SSH sessions (hangs) SSI includes from our web servers that fetch data from remote machines probably more What we see on the server when this something happens is the following: Load average go from basically nothing to around 3 CPU usage is still low (5%) Disk activity is low (running iostat) Plenty of memory available Plenty of disk space available In /var/log/messages we get the following: Jun 14 01:10:48 devvm kernel: e1000 0000:00:03.0: eth0: Detected Tx Unit Hang Jun 14 01:10:48 devvm kernel: Tx Queue <0> Jun 14 01:10:48 devvm kernel: TDH <2e> Jun 14 01:10:48 devvm kernel: TDT <30> Jun 14 01:10:48 devvm kernel: next_to_use <30> Jun 14 01:10:48 devvm kernel: next_to_clean <2e> Jun 14 01:10:48 devvm kernel: buffer_info[next_to_clean] Jun 14 01:10:48 devvm kernel: time_stamp <1038284db> Jun 14 01:10:48 devvm kernel: next_to_watch <2f> Jun 14 01:10:48 devvm kernel: jiffies <103828b42> Jun 14 01:10:48 devvm kernel: next_to_watch.status <0> Jun 14 01:10:50 devvm kernel: e1000 0000:00:03.0: eth0: Detected Tx Unit Hang Jun 14 01:10:50 devvm kernel: Tx Queue <0> Jun 14 01:10:50 devvm kernel: TDH <2e> Jun 14 01:10:50 devvm kernel: TDT <30> Jun 14 01:10:50 devvm kernel: next_to_use <30> Jun 14 01:10:50 devvm kernel: next_to_clean <2e> Jun 14 01:10:50 devvm kernel: buffer_info[next_to_clean] Jun 14 01:10:50 devvm kernel: time_stamp <1038284db> Jun 14 01:10:50 devvm kernel: next_to_watch <2f> Jun 14 01:10:50 devvm kernel: jiffies <103829312> Jun 14 01:10:50 devvm kernel: next_to_watch.status <0> Jun 14 01:10:52 devvm kernel: ------------[ cut here ]------------ Jun 14 01:10:52 devvm kernel: WARNING: at net/sched/sch_generic.c:261 dev_watchdog+0x26d/0x280() (Not tainted) Jun 14 01:10:52 devvm kernel: Hardware name: VirtualBox Jun 14 01:10:52 devvm kernel: NETDEV WATCHDOG: eth0 (e1000): transmit queue 0 timed out Jun 14 01:10:52 devvm kernel: Modules linked in: vboxsf(U) ipv6 ppdev parport_pc parport microcode sg vboxguest(U) i2c_piix4 i2c_core e1000 snd_intel8x0 snd_ac97_codec ac97_bus snd_seq snd_seq_device snd_pcm snd_timer snd soundcore snd_page_alloc pcnet32 mii ext4 mbcache jbd2 sd_mod crc_t10dif ahci dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan] Jun 14 01:10:52 devvm kernel: Pid: 0, comm: swapper Not tainted 2.6.32-279.el6.x86_64 #1 Jun 14 01:10:52 devvm kernel: Call Trace: Jun 14 01:10:52 devvm kernel: <IRQ> [<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0 Jun 14 01:10:52 devvm kernel: [<ffffffff8106b836>] ? warn_slowpath_fmt+0x46/0x50 Jun 14 01:10:52 devvm kernel: [<ffffffff814595fd>] ? dev_watchdog+0x26d/0x280 Jun 14 01:10:52 devvm kernel: [<ffffffff81099138>] ? sched_clock_cpu+0xb8/0x110 Jun 14 01:10:52 devvm kernel: [<ffffffff81459390>] ? dev_watchdog+0x0/0x280 Jun 14 01:10:52 devvm kernel: [<ffffffff8107e897>] ? run_timer_softirq+0x197/0x340 Jun 14 01:10:52 devvm kernel: [<ffffffff810a21c0>] ? tick_sched_timer+0x0/0xc0 Jun 14 01:10:52 devvm kernel: [<ffffffff8102b40d>] ? lapic_next_event+0x1d/0x30 Jun 14 01:10:52 devvm kernel: [<ffffffff81073ec1>] ? __do_softirq+0xc1/0x1e0 Jun 14 01:10:52 devvm kernel: [<ffffffff81096c50>] ? hrtimer_interrupt+0x140/0x250 Jun 14 01:10:52 devvm kernel: [<ffffffff8100c24c>] ? call_softirq+0x1c/0x30 Jun 14 01:10:52 devvm kernel: [<ffffffff8100de85>] ? do_softirq+0x65/0xa0 Jun 14 01:10:52 devvm kernel: [<ffffffff81073ca5>] ? irq_exit+0x85/0x90 Jun 14 01:10:52 devvm kernel: [<ffffffff81505be0>] ? smp_apic_timer_interrupt+0x70/0x9b Jun 14 01:10:52 devvm kernel: [<ffffffff8100bc13>] ? apic_timer_interrupt+0x13/0x20 Jun 14 01:10:52 devvm kernel: <EOI> [<ffffffff810387cb>] ? native_safe_halt+0xb/0x10 Jun 14 01:10:52 devvm kernel: [<ffffffff810149cd>] ? default_idle+0x4d/0xb0 Jun 14 01:10:52 devvm kernel: [<ffffffff81009e06>] ? cpu_idle+0xb6/0x110 Jun 14 01:10:52 devvm kernel: [<ffffffff814e433a>] ? rest_init+0x7a/0x80 Jun 14 01:10:52 devvm kernel: [<ffffffff81c21f7b>] ? start_kernel+0x424/0x430 Jun 14 01:10:52 devvm kernel: [<ffffffff81c2133a>] ? x86_64_start_reservations+0x125/0x129 Jun 14 01:10:52 devvm kernel: [<ffffffff81c21438>] ? x86_64_start_kernel+0xfa/0x109 Jun 14 01:10:52 devvm kernel: ---[ end trace 2c7bb984812cf120 ]--- Jun 14 01:10:52 devvm kernel: e1000 0000:00:03.0: eth0: Reset adapter Jun 14 01:10:53 devvm abrtd: Directory 'oops-2013-06-14-01:10:53-1537-0' creation detected Jun 14 01:10:53 devvm abrt-dump-oops: Reported 1 kernel oopses to Abrt Jun 14 01:10:53 devvm abrtd: Can't open file '/var/spool/abrt/oops-2013-06-14-01:10:53-1537-0/uid': No such file or directory Jun 14 01:10:55 devvm kernel: Bridge firewalling registered After this we see for a while, every two minutes: Jun 14 01:14:22 devvm kernel: INFO: task events/0:19 blocked for more than 120 seconds. Jun 14 01:14:22 devvm kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Jun 14 01:14:22 devvm kernel: events/0 D 0000000000000000 0 19 2 0x00000000 Jun 14 01:14:22 devvm kernel: ffff880116c4fb90 0000000000000046 00000000ffffffff 0000000000000008 Jun 14 01:14:22 devvm kernel: 0000000000016680 0000000000016680 ffff880028210400 0000000000016680 Jun 14 01:14:22 devvm kernel: ffff880116c4daf8 ffff880116c4ffd8 000000000000fb88 ffff880116c4daf8 Jun 14 01:14:22 devvm kernel: Call Trace: Jun 14 01:14:22 devvm kernel: [<ffffffff8105b483>] ? perf_event_task_sched_out+0x33/0x80 Jun 14 01:14:22 devvm kernel: [<ffffffff814fe6a5>] schedule_timeout+0x215/0x2e0 Jun 14 01:14:22 devvm kernel: [<ffffffff8100975d>] ? __switch_to+0x13d/0x320 Jun 14 01:14:22 devvm kernel: [<ffffffff814fe323>] wait_for_common+0x123/0x180 Jun 14 01:14:22 devvm kernel: [<ffffffff81060250>] ? default_wake_function+0x0/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff814fe43d>] wait_for_completion+0x1d/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff8108d093>] __cancel_work_timer+0x1b3/0x1e0 Jun 14 01:14:22 devvm kernel: [<ffffffff8108cbe0>] ? wq_barrier_func+0x0/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff8108d0f0>] cancel_work_sync+0x10/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffffa01c5ca5>] e1000_down_and_stop+0x25/0x50 [e1000] Jun 14 01:14:22 devvm kernel: [<ffffffffa01cb695>] e1000_down+0x155/0x200 [e1000] Jun 14 01:14:22 devvm kernel: [<ffffffffa01cbcb0>] ? e1000_reset_task+0x0/0xe0 [e1000] Jun 14 01:14:22 devvm kernel: [<ffffffffa01cbd1e>] e1000_reset_task+0x6e/0xe0 [e1000] Jun 14 01:14:22 devvm kernel: [<ffffffff8108c760>] worker_thread+0x170/0x2a0 Jun 14 01:14:22 devvm kernel: [<ffffffff810920d0>] ? autoremove_wake_function+0x0/0x40 Jun 14 01:14:22 devvm kernel: [<ffffffff8108c5f0>] ? worker_thread+0x0/0x2a0 Jun 14 01:14:22 devvm kernel: [<ffffffff81091d66>] kthread+0x96/0xa0 Jun 14 01:14:22 devvm kernel: [<ffffffff8100c14a>] child_rip+0xa/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff81091cd0>] ? kthread+0x0/0xa0 Jun 14 01:14:22 devvm kernel: [<ffffffff8100c140>] ? child_rip+0x0/0x20 Jun 14 01:14:22 devvm kernel: INFO: task parted:8069 blocked for more than 120 seconds. Jun 14 01:14:22 devvm kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Jun 14 01:14:22 devvm kernel: parted D 0000000000000003 0 8069 7994 0x00000080 Jun 14 01:14:22 devvm kernel: ffff8800908b3bb8 0000000000000082 0000000000000000 ffff88010ab50080 Jun 14 01:14:22 devvm kernel: ffff880116c7d500 0000000000000001 0000000000000000 0000000000000000 Jun 14 01:14:22 devvm kernel: ffff88010ab50638 ffff8800908b3fd8 000000000000fb88 ffff88010ab50638 Jun 14 01:14:22 devvm kernel: Call Trace: Jun 14 01:14:22 devvm kernel: [<ffffffff814fe6a5>] schedule_timeout+0x215/0x2e0 Jun 14 01:14:22 devvm kernel: [<ffffffff814fe323>] wait_for_common+0x123/0x180 Jun 14 01:14:22 devvm kernel: [<ffffffff81060250>] ? default_wake_function+0x0/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff8112b6d0>] ? lru_add_drain_per_cpu+0x0/0x10 Jun 14 01:14:22 devvm kernel: [<ffffffff814fe43d>] wait_for_completion+0x1d/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff8108d177>] flush_work+0x77/0xc0 Jun 14 01:14:22 devvm kernel: [<ffffffff8108cbe0>] ? wq_barrier_func+0x0/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff8108d2f3>] schedule_on_each_cpu+0x133/0x180 Jun 14 01:14:22 devvm kernel: [<ffffffff811ad440>] ? invalidate_bh_lru+0x0/0x50 Jun 14 01:14:22 devvm kernel: [<ffffffff8112ae35>] lru_add_drain_all+0x15/0x20 Jun 14 01:14:22 devvm kernel: [<ffffffff811adf6a>] invalidate_bdev+0x2a/0x50 Jun 14 01:14:22 devvm kernel: [<ffffffff8125e9a4>] blkdev_ioctl+0x3b4/0x6e0 Jun 14 01:14:22 devvm kernel: [<ffffffff811b381c>] block_ioctl+0x3c/0x40 Jun 14 01:14:22 devvm kernel: [<ffffffff8118dec2>] vfs_ioctl+0x22/0xa0 Jun 14 01:14:22 devvm kernel: [<ffffffff8118e064>] do_vfs_ioctl+0x84/0x580 Jun 14 01:14:22 devvm kernel: [<ffffffff8118e5e1>] sys_ioctl+0x81/0xa0 Jun 14 01:14:22 devvm kernel: [<ffffffff8100b0f2>] system_call_fastpath+0x16/0x1b In /var/spool/abrt/oops-2013-06-14-01:10:53-1537-0 we can see the following information: In backtrace: WARNING: at net/sched/sch_generic.c:261 dev_watchdog+0x26d/0x280() (Not tainted) Hardware name: VirtualBox NETDEV WATCHDOG: eth0 (e1000): transmit queue 0 timed out Modules linked in: vboxsf(U) ipv6 ppdev parport_pc parport microcode sg vboxguest(U) i2c_piix4 i2c_core e1000 snd_intel8x0 snd_ac97_codec ac97_bus snd_seq snd_seq_device snd_pcm snd_timer snd soundcore snd_page_alloc pcnet32 mii ext4 mbcache jbd2 sd_mod crc_t10dif ahci dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan] Pid: 0, comm: swapper Not tainted 2.6.32-279.el6.x86_64 #1 Call Trace: <IRQ> [<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0 [<ffffffff8106b836>] ? warn_slowpath_fmt+0x46/0x50 [<ffffffff814595fd>] ? dev_watchdog+0x26d/0x280 [<ffffffff81099138>] ? sched_clock_cpu+0xb8/0x110 [<ffffffff81459390>] ? dev_watchdog+0x0/0x280 [<ffffffff8107e897>] ? run_timer_softirq+0x197/0x340 [<ffffffff810a21c0>] ? tick_sched_timer+0x0/0xc0 [<ffffffff8102b40d>] ? lapic_next_event+0x1d/0x30 [<ffffffff81073ec1>] ? __do_softirq+0xc1/0x1e0 [<ffffffff81096c50>] ? hrtimer_interrupt+0x140/0x250 [<ffffffff8100c24c>] ? call_softirq+0x1c/0x30 [<ffffffff8100de85>] ? do_softirq+0x65/0xa0 [<ffffffff81073ca5>] ? irq_exit+0x85/0x90 [<ffffffff81505be0>] ? smp_apic_timer_interrupt+0x70/0x9b [<ffffffff8100bc13>] ? apic_timer_interrupt+0x13/0x20 <EOI> [<ffffffff810387cb>] ? native_safe_halt+0xb/0x10 [<ffffffff810149cd>] ? default_idle+0x4d/0xb0 [<ffffffff81009e06>] ? cpu_idle+0xb6/0x110 [<ffffffff814e433a>] ? rest_init+0x7a/0x80 [<ffffffff81c21f7b>] ? start_kernel+0x424/0x430 [<ffffffff81c2133a>] ? x86_64_start_reservations+0x125/0x129 [<ffffffff81c21438>] ? x86_64_start_kernel+0xfa/0x109 In cmdline: ro root=/dev/mapper/vg_01-lv_root rd_NO_LUKS LANG=en_US.UTF-8 KEYBOARDTYPE=pc KEYTABLE=sv-latin1 rd_NO_MD SYSFONT=latarcyrheb-sun16 rd_LVM_LV=vg_01/lv_root crashkernel=129M@0M rhgb quiet rd_LVM_LV=vg_01/lv_swap rd_NO_DM rhgb quie Additional information: # uname -a Linux devvm 2.6.32-279.el6.x86_64 #1 SMP Fri Jun 22 12:19:21 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux # cat /etc/redhat-release CentOS release 6.3 (Final) VirtualBox version 4.2.6. Any insight in how we can proceed with troubleshooting this is appreciated. If you need more information, just let me know.

    Read the article

  • Intel Dual Band Wireless-AC 7260 keeps dropping wifi

    - by Rick T
    My wifi Intel Dual Band Wireless-AC 7260 keeps dropping wificonnection drops and the network to which I was connected disappears from the list of available networks in network manager. The only way to fix it is to disable wifi and re-enable it How can I fix this. I'm using ubuntu 14.04 64bit. It mostly drops connections on the 5ghz network. My other devices don't drop connections over wifi. see logs and versions rt@simon:~$ uname -a Linux simon 3.13.0-34-generic #60-Ubuntu SMP Wed Aug 13 15:45:27 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux rt@simon:~$ rt@simon:~$ dmesg | grep iwl [ 3.370777] iwlwifi 0000:03:00.0: irq 46 for MSI/MSI-X [ 3.381089] iwlwifi 0000:03:00.0: loaded firmware version 22.24.8.0 op_mode iwlmvm [ 3.414637] iwlwifi 0000:03:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144 [ 3.414695] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 3.414913] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 3.630208] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' [ 9.304838] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 9.305068] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 605.483174] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 605.483396] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S rt@simon:~$ cat /var/log/syslog | grep -e iwl -e 80211 | tail -n25 Aug 14 08:13:02 simon kernel: [ 3.452780] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:13:02 simon kernel: [ 3.630208] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' Aug 14 08:13:06 simon NetworkManager[1125]: <info> rfkill1: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:1c.2/0000:03:00.0/ieee80211/phy0/rfkill1) (driver iwlwifi) Aug 14 08:13:06 simon NetworkManager[1125]: <info> (wlan0): using nl80211 for WiFi device control Aug 14 08:13:06 simon NetworkManager[1125]: <info> (wlan0): new 802.11 WiFi device (driver: 'iwlwifi' ifindex: 3) Aug 14 08:13:06 simon kernel: [ 9.304838] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:13:06 simon kernel: [ 9.305068] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:14:18 simon kernel: [ 81.230162] cfg80211: Calling CRDA to update world regulatory domain Aug 14 08:14:18 simon kernel: [ 81.232330] cfg80211: World regulatory domain updated: Aug 14 08:14:18 simon kernel: [ 81.232332] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Aug 14 08:14:18 simon kernel: [ 81.232333] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232334] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232335] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232336] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:14:18 simon kernel: [ 81.232337] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:02 simon kernel: [ 605.483174] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:23:02 simon kernel: [ 605.483396] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S Aug 14 08:23:18 simon kernel: [ 621.223905] cfg80211: Calling CRDA to update world regulatory domain Aug 14 08:23:18 simon kernel: [ 621.228945] cfg80211: World regulatory domain updated: Aug 14 08:23:18 simon kernel: [ 621.228950] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Aug 14 08:23:18 simon kernel: [ 621.228954] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228956] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228959] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228961] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Aug 14 08:23:18 simon kernel: [ 621.228963] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

    Read the article

  • Another sound not working post

    - by Thomas Smart
    Tried all the other "sound not working" posts i think, lost count. purge/reinstall alsa and pulse, reboot, add user to audio group, various lines in the alsa config file such as "options snd-hda-intel model=" then tried different options like generic, auto, basic, default, etc. tried pulseaudio -k && sudo alsa force-reload a few times, with and without rebooting. Hardware: 16gb ram, core I7-4790, Intel Haswell mboard with onboard sound and graphics Multimedia: Audio Adapter: HDA-Intel-HDA Intel HDMI OS: Ubuntu server 14.04 with ubuntu-desktop installed. GUI sound settings lists only the dummy sound card alsamixer -c 0 ¦ Card: HDA Intel HDMI F1: Help ¦ ¦ Chip: Intel Haswell HDMI F2: System information ¦ ¦ View: F3:[Playback] F4: Capture F5: All F6: Select sound card ¦ ¦ Item: S/PDIF ¦ ¦ +--+ ¦ ¦ ¦OO¦ ¦ ¦ +--+ ¦ ¦ < S/PDIF > ¦ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: HDMI [HDA Intel HDMI], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 aplay -L default Playback/recording through the PulseAudio sound server null Discard all samples (playback) or generate zero samples (capture) pulse PulseAudio Sound Server hdmi:CARD=HDMI,DEV=0 HDA Intel HDMI, HDMI 0 HDMI Audio Output dmix:CARD=HDMI,DEV=3 HDA Intel HDMI, HDMI 0 Direct sample mixing device dsnoop:CARD=HDMI,DEV=3 HDA Intel HDMI, HDMI 0 Direct sample snooping device hw:CARD=HDMI,DEV=3 HDA Intel HDMI, HDMI 0 Direct hardware device without any conversions plughw:CARD=HDMI,DEV=3 HDA Intel HDMI, HDMI 0 Hardware device with all software conversions cat /proc/asound/cards 0 [HDMI ]: HDA-Intel - HDA Intel HDMI HDA Intel HDMI at 0xf7d14000 irq 46 cat /proc/asound/devices 1: : sequencer 2: [ 0- 3]: digital audio playback 3: [ 0- 0]: hardware dependent 4: [ 0] : control 33: : timer mplayer -ao alsa:device=hdmi /usr/share/sounds/ubuntu/stereo/system-ready.ogg MPlayer 1.1-4.8 (C) 2000-2012 MPlayer Team mplayer: could not connect to socket mplayer: No such file or directory Failed to open LIRC support. You will not be able to use your remote control. Playing /usr/share/sounds/ubuntu/stereo/system-ready.ogg. libavformat version 54.20.4 (external) Mismatching header version 54.20.3 libavformat file format detected. [lavf] stream 0: audio (vorbis), -aid 0 Load subtitles in /usr/share/sounds/ubuntu/stereo/ ========================================================================== Opening audio decoder: [ffmpeg] FFmpeg/libavcodec audio decoders libavcodec version 54.35.0 (external) AUDIO: 44100 Hz, 1 ch, floatle, 80.0 kbit/5.67% (ratio: 10000->176400) Selected audio codec: [ffvorbis] afm: ffmpeg (FFmpeg Vorbis) ========================================================================== [AO_ALSA] alsa-lib: confmisc.c:768:(parse_card) cannot find card '1' [AO_ALSA] alsa-lib: conf.c:4248:(_snd_config_evaluate) function snd_func_card_driver returned error: No such file or directory [AO_ALSA] alsa-lib: confmisc.c:392:(snd_func_concat) error evaluating strings [AO_ALSA] alsa-lib: conf.c:4248:(_snd_config_evaluate) function snd_func_concat returned error: No such file or directory [AO_ALSA] alsa-lib: confmisc.c:1251:(snd_func_refer) error evaluating name [AO_ALSA] alsa-lib: conf.c:4248:(_snd_config_evaluate) function snd_func_refer returned error: No such file or directory [AO_ALSA] alsa-lib: conf.c:4727:(snd_config_expand) Evaluate error: No such file or directory [AO_ALSA] alsa-lib: pcm.c:2239:(snd_pcm_open_noupdate) Unknown PCM hdmi [AO_ALSA] Playback open error: No such file or directory Failed to initialize audio driver 'alsa:device=hdmi' Could not open/initialize audio device -> no sound. Audio: no sound Video: no video Exiting... (End of file) mplayer -ao alsa:device=hw=0.3 /usr/share/sounds/ubuntu/stereo/system-ready.ogg MPlayer 1.1-4.8 (C) 2000-2012 MPlayer Team mplayer: could not connect to socket mplayer: No such file or directory Failed to open LIRC support. You will not be able to use your remote control. Playing /usr/share/sounds/ubuntu/stereo/system-ready.ogg. libavformat version 54.20.4 (external) Mismatching header version 54.20.3 libavformat file format detected. [lavf] stream 0: audio (vorbis), -aid 0 Load subtitles in /usr/share/sounds/ubuntu/stereo/ ========================================================================== Opening audio decoder: [ffmpeg] FFmpeg/libavcodec audio decoders libavcodec version 54.35.0 (external) AUDIO: 44100 Hz, 1 ch, floatle, 80.0 kbit/5.67% (ratio: 10000->176400) Selected audio codec: [ffvorbis] afm: ffmpeg (FFmpeg Vorbis) ========================================================================== [AO_ALSA] Format floatle is not supported by hardware, trying default. AO: [alsa] 44100Hz 2ch s16le (2 bytes per sample) Video: no video Starting playback... A: 0.4 (00.4) of 0.8 (00.7) 0.1% Exiting... (End of file) Thank you for your time and help :)

    Read the article

  • How to set default xrandr settings?

    - by echo-flow
    I'm trying to enable dual monitors in Ubuntu. This is working fine, but every time I do it, desktop effects is disabled. I think I've found the reason why, though: https://wiki.ubuntu.com/X/Config/Multihead/ As with the GNOME XRandR configuration method, setting Virtual to too large a value may result in a loss of hardware acceleration, and thus an inability to use Compiz and its desktop effects. When I use the GNOME monitor applet, or the Monitors configuration in the System menu, the default xrandr settings puts the second monitor to the right of the first, and, as I found with this bug, for most monitors this creates a virtual desktop larger than the maximum 2048 horizontal resolution needed for hardware acceleration on my netbook hardware. So, it seems like if I can modify xrandr's default settings so that it places the new desktop above or below (north or south of) the main LVDS display, then hardware acceleration, and therefore compiz will continue to work. Can anyone tell me, what is the easiest way to achieve this? UPDATE: I have confirmed that multihead support with desktop effects and hardware acceleration works when I move the external monitor display north of the main LVDS display. Right now this involves the following process: plugging in the external monitor, starting the Monitors configuration menu, desktop effects are disabled automatically (and all of the windows on my workspaces are moved to the first workspace), repositioning the external display so that it is north of LVDS display and clicking apply, and then navigating to the Appearance menu and telling it to reenable desktop effects. Is there a simpler way do this? UPDATE 2: OK, so I thought that perhaps the GNOME Monitors configuration screen was trying to be clever, and might be disbling desktop effects. So, I just tried using the xrandr command-line client instead, as follows: xrandr --output VGA1 --above LVDS1 When I do that, desktop effects are still disabled, and I need to manually reenable them. This, despite the fact that hardware acceleration works, and there is never a point where hardware acceleration stops working because the horizontal dimension of the virtual display is too large. So what program is trying to be clever, and is turning off desktop effects when it doesn't need to? And how do I make it stop? If there were a way to re-enable desktop effects from the command line, which I could then put into a script along with the proper xrandr invocation, I would accept that as a workaround. UPDATE 3: OK, here's my script to enable a second monitor with desktop effects. It might be evil, I'm not sure: second-monitor.sh xrandr --output VGA1 --above LVDS1 sleep 3 compiz --replace & The sleep statement might not be necessary. If there's a better way to do this, please let me know. UPDATE 4: This is a Dell Mini Inspiron 1012. Here are my system specifications: lspci -vv 00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller Subsystem: Dell Device 041a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 29 Region 0: Memory at f0b00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at 18d0 [size=8] Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at f0900000 (32-bit, non-prefetchable) [size=1M] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller Subsystem: Dell Device 041a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at f0b80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> lsmod | grep i915 i915 287458 2 drm_kms_helper 29329 1 i915 drm 162409 3 i915,drm_kms_helper intel_agp 24375 2 i915 i2c_algo_bit 5028 1 i915 video 17375 1 i915

    Read the article

  • Ubuntu 12.04 / 12.10 Randomly Freezing - nVidia?

    - by Alix Axel
    My Ubuntu install frequently freezes, sometimes showing a black screen (not very common anymore - in my latest installs), some other times the mouse and keyboard just fail to move and respond (not even Ctrl + Alt + F1 works) and some other times I'm able to move the mouse with a huge delay (2-5 seconds) but I'm not able to do/click anything. I have a pretty strong feeling that this problem is related to my graphic card drivers because: after hard reset, I usually get error reports about X.org / jockey it's common for artifacts to appear during loading / shutdown / whenever, for instance: pattern filled with £ during log off ugly-colored squared pattern during boot windows that are partially moved (i.e.: only the top half) Firefox renderings that leave the bottom ~30% of the page black These artifacts appear right before the system freezes. I've installed Ubuntu 12.04 LTS and after several failed attempts to get my dual monitor setup to work properly I tried installing the new 12.10 version, hoping that this new version would have this problem solved... Unfortunatly, that was not the case, so I reverted to Ubuntu 12.04. I've tried all the drivers in the Additional Drivers application (even the experimental ones), I've also tried the nvidia-current package from the PPA repository ubuntu-x-swat/x-updates as well as the nouveau OSS driver. Nothing (except no driver at all with a 640*480 resolution) at all seems stable. Here is the info of my graphic card: alix@alix-E500:~$ lspci | grep VGA 01:00.0 VGA compatible controller: NVIDIA Corporation G86 [GeForce 8400M G] (rev a1) alix@alix-E500:~$ sudo lshw -C video [sudo] password for alix: *-display description: VGA compatible controller product: G86 [GeForce 8400M G] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:fd000000-fdffffff memory:d0000000-dfffffff memory:fa000000-fbffffff ioport:cc00(size=128) memory:fe0e0000-fe0fffff Right now, I don't even have my 22" monitor connected as I can't even get my laptop display to work properly and without freezes. I've searched, read and tried all that I could (over several fresh reinstalls) to fix the problem, but so far, no solution has proven definitive. I'm sorry I can't precise which symptom maps to each driver but I've been trying to solve this one on my own without logging what I'm doing, perhaps someone here will be able to point me to a certain-fix solution, if not I'll keep updating this question as I go along. Please let me know if any more info is needed to pinpoint the exact problem. Trying out NVIDIA accelerated graphics driver (version 173). The scrolling, minimizing / maximizing windows takes between 2 and 5 seconds to finalize. Context menus also pop up very slowly and the typing seems delayed by ~1 second. No critical issues so far. Firefox rendering of the Save Edits button is consistently messed up (random black lines in the top). Trying out NVIDIA accelerated graphics driver (version current) [Recommended]. All the delays mentioned above and the buggy rendering of the Save Edits button are gone, but I'm noticing that the whole screen flashes black for a couple of microseconds and while I was writing this test for the first time, the bottom 30% of the screen went black and I couldn't do anything (not even Ctrl + Alt + F1 would work). Had to force a hard reset. Also, the system hanged a little for a couple of seconds with the fade out of the "Restart" menu. Trying out NVIDIA accelerated graphics driver (*experimental*beta) (version experimental-304). Same symptoms as before, it crashed once while I was trying to install Chromium and again after a hard reset when I was trying to remove the driver. The bottom of the screen did not went black and I could move my mouse both times. Ctrl + Alt + F1 didn't work. The ugly-colored pattern also showed up during the second boot. Trying out NVIDIA accelerated graphics driver (*experimental*beta) (version experimental-307). The system crashed as soon as I clicked something. Had to do a fresh re-install. Trying out Nouveau: Accelerated Open Source driver for nVidia cards. Artifacts still show up during boot but other than that this one seems stable. As soon as I connected my second monitor, the responsiveness dropped a lot, animations and video are somewhat slow. I'm gonna try this solution http://askubuntu.com/a/98871/9018 later on.

    Read the article

  • Nec USB 3.0 controller drops connection - Ubuntu 12.04.1

    - by Tom
    I have some serious problems with Technaxx pci-e 302p card. It has uPD720200a NEC chip with 4020 firmware. BIOS recognises it. Sometimes it recognises devices and system mounts them and are functional for few minutes, other times they can't be mount and error occours. After fresh install card worked fine, but after kernel and firmware update it behaves as mentioned. Outputs: uname -a Linux asd-GA-MA770-UD3 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:52:48 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lspci -vvv USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fd8fe000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: xhci_hcd lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 07d1:3c0a D-Link System DWA-140 RangeBooster N Adapter(rev.B2) [Ralink RT3072] Bus 005 Device 004: ID 1997:1221 Bus 005 Device 003: ID 15c2:003c SoundGraph Inc. lsmod Module Size Used by nls_iso8859_1 12713 0 nls_cp437 16991 0 vfat 17585 0 fat 61512 1 vfat vesafb 13844 1 saa7134_alsa 18602 1 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep tda827x 18182 1 snd_hda_codec_hdmi 32474 1 ir_lirc_codec 12859 0 lirc_dev 19204 1 ir_lirc_codec tda8290 22616 1 arc4 12529 2 snd_hda_codec_realtek 224173 1 ir_mce_kbd_decoder 12777 0 ir_sony_decoder 12510 0 ir_jvc_decoder 12507 0 tuner 27428 1 ir_rc6_decoder 12507 0 snd_hda_intel 33773 5 rt2800usb 22684 0 rt2800lib 58925 1 rt2800usb crc_ccitt 12667 1 rt2800lib rt2x00usb 20762 1 rt2800usb rt2x00lib 51144 3 rt2800usb,rt2800lib,rt2x00usb mac80211 506816 3 rt2800lib,rt2x00usb,rt2x00lib ir_rc5_decoder 12507 0 rc_avermedia_m135a 12526 0 rc_imon_pad 12505 0 ir_nec_decoder 12507 0 cfg80211 205544 2 rt2x00lib,mac80211 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_ctxfi 111202 2 snd_hwdep 13668 1 snd_hda_codec imon 32839 0 snd_pcm 97188 5 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_ctxfi snd_seq_midi 13324 0 saa7134 181851 1 saa7134_alsa videobuf_dma_sg 19354 2 saa7134_alsa,saa7134 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi joydev 17693 0 rc_core 26412 13 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_avermedia_m135a,rc_imon_pad,ir_nec_decoder,imon,saa7134 snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 101 videobuf_core 26390 2 saa7134,videobuf_dma_sg v4l2_common 16454 2 tuner,saa7134 videodev 98259 3 tuner,saa7134,v4l2_common sp5100_tco 13791 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 28 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_ctxfi,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device v4l2_compat_ioctl32 17128 1 videodev tveeprom 21249 1 saa7134 i2c_piix4 13301 0 soundcore 15091 1 snd edac_core 53746 0 serio_raw 13211 0 snd_page_alloc 18529 3 snd_hda_intel,snd_ctxfi,snd_pcm edac_mce_amd 23709 0 wmi 19256 0 mac_hid 13253 0 ppdev 17113 0 parport_pc 32866 1 k10temp 13166 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp usb_storage 49198 0 uas 18180 0 usbhid 47199 0 hid 99559 1 usbhid firewire_ohci 41000 0 firewire_core 63558 1 firewire_ohci crc_itu_t 12707 1 firewire_core floppy 70365 0 pata_atiixp 13204 2 r8169 62099 0 dmesg | tail after plugging to usb 3.0 port [ 834.871296] sd 9:0:0:0: rejecting I/O to offline device [ 834.871308] sd 9:0:0:0: rejecting I/O to offline device [ 834.871319] sd 9:0:0:0: rejecting I/O to offline device [ 834.871330] sd 9:0:0:0: rejecting I/O to offline device [ 834.871530] sd 9:0:0:0: [sdd] Unhandled error code [ 834.871536] sd 9:0:0:0: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 834.871545] sd 9:0:0:0: [sdd] CDB: Read(10): 28 00 0e 8e 48 0a 00 00 3e 00 [ 834.871564] end_request: I/O error, dev sdd, sector 244205578 [ 834.875497] sd 8:0:0:1: Device offlined - not ready after error recovery [ 834.885339] usb 9-2: USB disconnect, device number 2 Are there any other outputs need for answering? I'll post them ASAP. I could of course reject updating the system but I think it's halfway solution. Any help appreciated. BTW USB 2.0 and 1.1 ports run well, card itself runs under win7 as charm. Tom

    Read the article

  • Slow wired internet connection on Realtek RTL8168-8111 (Rev 6)

    - by Mark
    I keep on seeing issues people are having with their wireless. I am having an issue with being wired into my router. I installed Ubuntu 11.10 the other day, on my custom PC. The motherboard I have installed on this PC is an ASUS P8H61-M. The issue I am having is with my speed. I have a dual boot, windows 7 and the new Ubuntu. On my Windows install I am getting test speeds from Speakeasy at 17Mbps and actual downloads around 2-3MB/s. With Ubuntu, I am getting test speeds from Speakeasy at 1.14Mbps and actual downloads around 60KB/s. I have disabled IPv6 and am no using GoogleDNS for my DNS, but it hasn't resolved the issue. I have scanned my router (WRT54GS Linksys) to disable IPv6 connections, and I am not seeing any option for that. I cannot figure out why I am getting such sluggish internet connection. Any help to resolve would be great! I performed an iconfig -a with these results: mark@Mark-ASUS:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr f4:6d:04:d1:2c:4e inet addr:192.168.1.103 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::f66d:4ff:fed1:2c4e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:21888 errors:0 dropped:21888 overruns:0 frame:21888 TX packets:21068 errors:0 dropped:90 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:26348337 (26.3 MB) TX bytes:2217140 (2.2 MB) Interrupt:46 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:952 (952.0 B) TX bytes:952 (952.0 B) My specs are: mark@Mark-ASUS:~$ sudo lspci -nn 04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) 06:00.0 PCI bridge [0604]: ASMedia Technology Inc. Device [1b21:1080] (rev 01) udev information: KERNEL[11.351405] add /devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 (net) UDEV_LOG=3 ACTION=add DEVPATH=/devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 SUBSYSTEM=net INTERFACE=eth0 IFINDEX=2 SEQNUM=1542 UDEV [11.363905] add /devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 (net) UDEV_LOG=3 ACTION=add DEVPATH=/devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 SUBSYSTEM=net INTERFACE=eth0 IFINDEX=2 SEQNUM=1542 ID_VENDOR_FROM_DATABASE=Realtek Semiconductor Co., Ltd. ID_MODEL_FROM_DATABASE=RTL8111/8168B PCI Express Gigabit Ethernet controller ID_BUS=pci ID_VENDOR_ID=0x10ec ID_MODEL_ID=0x8168 ID_MM_CANDIDATE=1 dmesg information: [ 2.855982] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.856366] r8169 0000:04:00.0: eth0: RTL8168b/8111b at 0xffffc9000064c000, f4:6d:04:d1:2c:4e, XID 0c900800 IRQ 46 [ 12.540956] r8169 0000:04:00.0: eth0: link down [ 12.540961] r8169 0000:04:00.0: eth0: link down [ 12.541173] ADDRCONF(NETDEV_UP): eth0: link is not ready I took out a lot of information that did not pertain to eth0, because the previous edits wouldn't save. If I need any more information, let me know. I would love to get this resolved. The other issue I am noticing is sometimes my connection disconnects all together, for about a minute, then it reconnects.

    Read the article

  • Errors when trying to compile the driver for the rtl8192su wireless adapter

    - by Tom Brito
    I have a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g sudo lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) sudo lsusb Bus 002 Device 003: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 045e:00f9 Microsoft Corp. Wireless Desktop Receiver 3.1 Bus 001 Device 003: ID 0b05:1786 ASUSTek Computer, Inc. Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

    Read the article

  • Dell 3721 Wifi problem Ubuntu 13.04

    - by Sebastian
    I have a Dell 3721 which comes original with windows 8. I managed it to install ubuntu 12.10 on this laptop, even there was no out of the box drivers. With 12.10 I was forces to install this .deb package couple of times. After installing it, it was ok for some weeks before I have to install it again. Maybe some security updates destroy something which made in necessary to install it again... http://jas.gemnetworks.com/debian/pool/main/w/wireless-bcm43142/wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb My problem is, that this package isnt working with ubuntu 13.04 anymore. So I cant use Wifi now. Also my display is almost dark, I cant change the brightness level with ubuntu 13.04. Hope you can give me some advice. Dell:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM Controller [8086:0154] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) 00:1c.1 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 [8086:1e12] (rev c4) 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation HM76 Express Chipset LPC Controller [8086:1e59] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04) 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 02:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01) @Dell:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0a5c:21d7 Broadcom Corp. Bus 001 Device 004: ID 0bda:0129 Realtek Semiconductor Corp. Bus 001 Device 005: ID 0c45:64ad Microdia @Dell:~$ lspci -nn | grep VGA 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) @Dell:~$ sudo lshw -class network *-network Beschreibung: Ethernet interface Produkt: RTL8101E/RTL8102E PCI Express Fast Ethernet controller Hersteller: Realtek Semiconductor Co., Ltd. Physische ID: 0 Bus-Informationen: pci@0000:01:00.0 Logischer Name: eth0 Version: 05 Seriennummer: xx:xx:xx:xx:xx:xx Größe: 100Mbit/s Kapazität: 100Mbit/s Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation Konfiguration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.103 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s Ressourcen: irq:42 ioport:2000(Größe=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network UNGEFORDERT Beschreibung: Network controller Produkt: BCM43142 802.11b/g/n Hersteller: Broadcom Corporation Physische ID: 0 Bus-Informationen: pci@0000:02:00.0 Version: 01 Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress bus_master cap_list Konfiguration: latency=0 Ressourcen: memory:c0500000-c0507fff

    Read the article

  • How to make Ubuntu recognize an unknown external display (so I can adjust its resolution)?

    - by WagnerAA
    I have a Dell laptop with an external monitor attached (a Samsumg SyncMaster 931c). My laptop display was recognized, and I can adjust its optimum resolution. My external display is still unknown, thus I'm stuck at a lower resolution (1024x768): I tried the "Detect Displays" button, but it didn't work, nothing happens. I recently upgraded from Ubuntu 12.04 to 12.10. Things were working before. I don't know if I can actually change this configuration, or if this is a bug. I searched for an answer here and also in Launchpad's website, but found none. I even tried to install Nvidia drivers, and just messed things up. It seems I wasn't even using nvidia before, as I guessed by looking at my additional drivers configuration: My laptop has an Intel chipset, I guess: $ dpkg --get-selections | grep -i -e nvidia -e intel intel-gpu-tools install libdrm-intel1:amd64 install libdrm-intel1:i386 install nvidia-common install xserver-xorg-video-intel install I don't have an xorg.conf file (I think this is nvidia related, am I right?): $ cat /etc/X11/xorg.conf cat: /etc/X11/xorg.conf: No such file or directory $ ls -l /etc/X11/ total 76 drwxr-xr-x 2 root root 4096 Out 19 23:41 app-defaults drwxr-xr-x 2 root root 4096 Abr 25 2012 cursors -rw-r--r-- 1 root root 18 Abr 25 2012 default-display-manager drwxr-xr-x 4 root root 4096 Abr 25 2012 fonts -rw-r--r-- 1 root root 17394 Dez 3 2009 rgb.txt lrwxrwxrwx 1 root root 13 Mai 1 03:33 X -> /usr/bin/Xorg drwxr-xr-x 3 root root 4096 Out 19 23:41 xinit drwxr-xr-x 2 root root 4096 Jan 23 2012 xkb -rw-r--r-- 1 root root 0 Out 24 08:55 xorg.conf.nvidia-xconfig-original -rwxr-xr-x 1 root root 709 Abr 1 2010 Xreset drwxr-xr-x 2 root root 4096 Out 19 10:08 Xreset.d drwxr-xr-x 2 root root 4096 Out 19 10:08 Xresources -rwxr-xr-x 1 root root 3730 Jan 20 2012 Xsession drwxr-xr-x 2 root root 4096 Out 20 00:11 Xsession.d -rw-r--r-- 1 root root 265 Jul 1 2008 Xsession.options -rw-r--r-- 1 root root 13 Ago 15 06:43 XvMCConfig -rw-r--r-- 1 root root 601 Abr 25 2012 Xwrapper.config Here is some information I gathered by looking at other related posts: $ sudo lshw -C display; lsb_release -a; uname -a *-display:0 description: VGA compatible controller product: Mobile 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 07 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:48 memory:f6800000-f6bfffff memory:d0000000-dfffffff ioport:1800(size=8) *-display:1 UNCLAIMED description: Display controller product: Mobile 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 07 width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: latency=0 resources: memory:f6100000-f61fffff LSB Version: core-2.0-amd64:core-2.0-noarch:core-3.0-amd64:core-3.0-noarch:core-3.1-amd64:core-3.1-noarch:core-3.2-amd64:core-3.2-noarch:core-4.0-amd64:core-4.0-noarch:cxx-3.0-amd64:cxx-3.0-noarch:cxx-3.1-amd64:cxx-3.1-noarch:cxx-3.2-amd64:cxx-3.2-noarch:cxx-4.0-amd64:cxx-4.0-noarch:desktop-3.1-amd64:desktop-3.1-noarch:desktop-3.2-amd64:desktop-3.2-noarch:desktop-4.0-amd64:desktop-4.0-noarch:graphics-2.0-amd64:graphics-2.0-noarch:graphics-3.0-amd64:graphics-3.0-noarch:graphics-3.1-amd64:graphics-3.1-noarch:graphics-3.2-amd64:graphics-3.2-noarch:graphics-4.0-amd64:graphics-4.0-noarch:printing-3.2-amd64:printing-3.2-noarch:printing-4.0-amd64:printing-4.0-noarch:qt4-3.1-amd64:qt4-3.1-noarch Distributor ID: Ubuntu Description: Ubuntu 12.10 Release: 12.10 Codename: quantal Linux Batcave 3.5.0-17-generic #28-Ubuntu SMP Tue Oct 9 19:31:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux $ xrandr -q Screen 0: minimum 320 x 200, current 2304 x 800, maximum 32767 x 32767 LVDS1 connected 1280x800+0+0 (normal left inverted right x axis y axis) 286mm x 1790mm 1280x800 59.9*+ 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 connected 1024x768+1280+32 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9 DP1 disconnected (normal left inverted right x axis y axis) If there's anything else I can do, any other information I can post here, to help me configure this external display, please let me know. If this is actually a bug, I apologize (I know bugs are not allowed here), but I really wasn't sure. And I will promptly file a bug report in Launchpad if that's the case. Thanks a lot in advance. ;)

    Read the article

  • What's wrong with my wireless?

    - by dazzle
    I am having issues with my wireless connection. My connection is constantly disconnecting, then attempting to reconnect, reconnecting momentarily, then disconnecting etc. on times scales that range from seconds to minutes. In the meantime, needless to say I'm having significant packet loss. I'm running Ubuntu 14.04 64bit, updated and upgraded to today. Here is my card and driver: delta@sager:~$ lspci -vq | grep -i wireless -B 1 -A 5 04:00.0 Network controller: Intel Corporation Wireless 7260 (rev 73) Subsystem: Intel Corporation Dual Band Wireless-AC 7260 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at f7d00000 (64-bit, non-prefetchable) [size=8K] Capabilities: Kernel driver in use: iwlwifi Here is my kernel: delta@sager:~$ uname -r 3.13.0-34-generic None of the other machines on my home network are having these issues. Windows Vista is networking without issue for goodness sake ;-) Here is a small clipping from the output of dmesg. As you can see, I am getting a cfg80211 message of some sort over and over again (FYI, I've replaced my MAC address with a series of dashes, so anytime there is a ---------------, that was where the MAC address was: [ 1881.739161] wlan1: authenticate with --------------- [ 1881.741561] wlan1: send auth to --------------- (try 1/3) [ 1881.743440] wlan1: authenticated [ 1881.746027] wlan1: associate with --------------- (try 1/3) [ 1881.749244] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1881.754727] wlan1: associated [ 1881.754827] cfg80211: Calling CRDA for country: US [ 1881.761552] cfg80211: Regulatory domain changed to country: US [ 1881.761559] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1881.761564] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1881.761568] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1881.761571] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761574] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761577] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761580] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1881.761584] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1882.391038] cfg80211: Calling CRDA to update world regulatory domain [ 1882.396254] cfg80211: World regulatory domain updated: [ 1882.396260] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1882.396265] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396268] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396271] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1882.396274] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396277] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.148252] wlan1: authenticate with --------------- [ 1886.150005] wlan1: send auth to --------------- (try 1/3) [ 1886.151807] wlan1: authenticated [ 1886.154847] wlan1: associate with --------------- (try 1/3) [ 1886.158147] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1886.163464] wlan1: associated [ 1886.163520] wlan1: Limiting TX power to 30 (30 - 0) dBm as advertised by --------------- [ 1886.163588] cfg80211: Calling CRDA for country: US [ 1886.170500] cfg80211: Regulatory domain changed to country: US [ 1886.170508] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1886.170513] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1886.170517] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1886.170520] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170523] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170526] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170529] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1886.170533] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1887.200197] cfg80211: Calling CRDA to update world regulatory domain [ 1887.203655] cfg80211: World regulatory domain updated: [ 1887.203659] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1887.203662] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203664] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203666] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1887.203668] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203670] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) I've poked around on AskUbuntu, and have not found any adequate solutions; have also found similar threads that were left unanswered. Any advice/experience/threads I might be able to pull on would be greatly appreciated. In your opinion, is this a kernel issue, hardware issue, etc.? Thanks in advance. EDIT: chili, here's the output of iwconfig: delta@sager:~$ iwconfig wlan1 IEEE 802.11abg ESSID:"LANbeforetime" Mode:Managed Frequency:2.412 GHz Access Point: ----------- Bit Rate=48 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=44/70 Signal level=-66 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:80 Missed beacon:0 eth0 no wireless extensions. lo no wireless extensions.

    Read the article

< Previous Page | 11 12 13 14 15 16 17  | Next Page >