Search Results

Search found 988 results on 40 pages for 'josh pearce'.

Page 15/40 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

• Linux Mint Constantly freezing on Dell XPS L502X

  - by Josh

  I recently partitioned my hard drive to dual boot the existing Windows 7 with Linux Mint because I am tired of using Windows, especially the lack of terminal. I want to eventually remove Windows 7 and just run it from a VM within Linux Mint, but I want to make sure that I like the Mint before going all in. I ran Linux Mint on a VM inside Windows for a while, enjoyed it, and never had any issues with it. Since installing on my hard drive it has started freezing every 5-10 minutes, and the only way to get it back is to either power down, or close the lid and reopen once it sleeps. I've also tried running Ubuntu on dual boot in the past, and while it never froze, the battery life was terrible, and the fan was constantly running. I'm experiencing the same battery/fan problem with Mint, which doesn't make sense to me, as Linux should be lighter on the CPU than windows. If I had to guess I'd say it's probably a driver thing, with my video card or fan or something. My battery life in Windows is ~2 hours and its about 40 minutes in Linux. At this point, that is even if my laptop doesn't freeze before then. On a less important note, I also have an intel Centrino 6150 WiMax card that I'd like to be able to use, but that won't register on the Linux system either. I have tried downloading drivers for both of these, but neither have solved my problems. I'm definitely getting frustrated and am getting close to giving up on Linux even though I dread working on a Windows machine.

  Read the article

• How to split audio into multiple channels from optical S/PDIF or 1/8"?

  - by Josh M.

  I have a motherboard which has an optical S/PDIF output or 1/8". I'd like to "split" that signal into the appropriate channels so that I can then connect that to the wires behind my car's headunit which, in turn, run to the amp. The factory Bose amp just takes a single connector with a million wires running out of it, so that's why I would need to separate the signal into separate channels. On the other end there are four RCA connectors: front left, front right, rear left, rear right. The sub-woofer signal does not require an additional connection. Edit: Revised to include S/PDIF or 1/8".

  Read the article

• Add Clamd as a service to CentOS?

  - by Josh

  As I understand I think I need to add something to init.d, but I am not sure what to add. At the moment to start clamav I have to do clamd start. I would like it as a service so I can start it on run level 3 as a service. I realize I could probably do this through a shell script in the right runlevel, but I would like to be able to use chkconfig to configure it.

  Read the article

• CHROOT for shell script testing

  - by Josh

  I am looking at setting up a shell script in order to properly document and automate the process I am using to setup a few servers we have. In order to test the shell script through its different stages I was thinking a CHROOT would be ideal, since I can wipe out the "virtual root" and create it on the fly. I have never used CHROOT before, however. I was just curious what are the exact steps I would need to follow to implement this process of creating a chroot (with the basic core functions that would be needed to install apache/php/etc.)? and then destroying it?

  Read the article

• Primary/secondary ethernet interfaces via NetworkManager in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local... EDIT: Here's my routing table: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.151.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 172.16.30.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.1.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 172.16.30.2 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.0.1 0.0.0.0 UG 0 0 0 eth1 I want the 172.16.30.2 network to be the primary one and the 10.1.0.0 network to be the secondary one. EDIT2: My nameservers are also incorrect. It seems like Ubuntu is bringing the networks up in order, eth0, then 1, then 2, and the DHCP information from eth1 is overriding eth0, and eth2 is overriding eth1. How can I reverse this so the DHCP information from eth0 is the "master"? EDIT3: This seems to be an issue with Gnome's NetworkManager.

  Read the article

• View Public Key in Domain Key for a Domain

  - by Josh

  Using Jeff's blog post I'm creating domain keys for my account. I wanted to verify the setup using Get or Host command with Bind for Windows but I'm lost one of the commands. I can see view the _domainkey. txt file with this command: host -t txt _domainkey.stackoverflow.com but I'm at a loss at how I'd find the selector record. Jeff points out it can be anything before the before the period in "._domainkey.domain.com" but how would I list all records if I didn't know the exact query name? Is there a wildcard I could use to view all TXT or all records under this section?

  Read the article

• Installed Bunch of New Fonts on Windows 7 - Now None Show Up and System Lags

  - by Josh Stodola

  So I went to install about 5,000 fonts on my Windows 7 64-bit machine. It was slow to install them, and I had to leave. I came back and my PC was shut down, and I had to go through the Windows recovery BS when I powered it on. Now my computer runs EXTREMELY slow and any program that has a font menu locks up my whole machine (nothing in Microsoft Office works). When I go to "Fonts" in the control panel, it says 0 items. I went through all of the font settings trying to get them to appear. Nothing helps. I tried to bring up the Character Map and that froze up my machine too. How can I fix this? If I do not get this issue resolved soon, I am wiping this drive and going back to XP (and probably never purchasing another version of Windows again). I never had any issues with XP and have had nothing but performance problems when switching to Windows 7. My quad-core intel extreme with 8GB of RAM should never flinch with the kind of work that I do, and something simple like playing a song off an external HD takes up to five seconds on Windows 7. Unbelievable that I had to pay for this crap!

  Read the article

• Setting up Konico Minolta 1400w printer on windows vista 32bit

  - by Josh

  One of my neighbors asked me to help them setup this old printer on their computer (thier other printer is broken) so after fighting with it for about an hour but to no avail. Every time I try to install it, windows just recognizes it a as "print to file printer" as in it will only print to an output file. It's kinda urgent so speedy help would be appreciated.

  Read the article

• How can I avoid my web browser from redirecting to localhost using WAMP in Windows7?

  - by Josh

  I'm currently using Windows 7 with WAMP to try and work on some software, but my web browsers will not accept cookies from the "localhost" domain. I tried creating a few bogus domains in my hosts file by pointing them to 127.0.0.1 but when I type them in I am automatically redirected back to localhost. I have also configured virtualhosts in apache to correspond with the domains I added to the hosts file and it still redirects back to localhost. Is there anything special I must do on Windows 7 to get around this localhost redirect? Thanks for looking :) I'll include my host file here: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost 127.0.0.1 magento.localhost.com www.localhost.com Thanks for looking :)

  Read the article

• Is it faster to create indexes before or after data loading in MySQL?

  - by Josh Glover

  I have a data replication process that drops and recreates a few tables in a target database, then loads them up with data from a source database (running on another host, but that is immaterial to the question at hand). The target database does need primary keys and a few other indexes on its tables, but not during the data loading. I'm currently loading all of the data, then creating the indexes. However, index creation takes a pretty long time--30 minutes of my data loader's 5 and a half hour running time. My intuition tells me that creating the indexes at the end should be faster than creating them first, since the index would need to be rewritten with each insert. Can anyone tell me for sure which way is faster? FWIW, I'm running MySQL 5.1 with InnoDB tables.

  Read the article

• Stupid question: prevent file from being changed under linux

  - by Josh

  Ok. Stupid question. I have forgotten what this is called and without remembering the name the search function on the site and on google is failing me. What's the command under linux to mark a file as "locked"/to prevent any changes from being made to it? I'm not talking about chmod. There's a property that can be set (again the name escapes me at the moment) which prevents even processes running as root from changing a file. What is this called and how do I set it?

  Read the article

• Managing rolling deployments in the cloud

  - by Josh Nankin

  Recently I've been experimenting with various cloud management tools like RightScale, Scalr, custom scripts for managing a variety of servers, each hosting several roles (app, db, load balancer, job queues, etc). The one thing I find lacking in most solutions is a way to do rolling deployments, i.e. running deployments sequentially across a number of servers with the same role. For instance, I dont want to build all of my webservers at the same time, as that will almost definitely result in some down time or 500s for my customers. I'd rather have one or two servers build at a time, while other servers are still available to handle requests. The other alternative is obviously to launch new servers that automatically update themselves on boot, but this isn't as cost effective, and most likely requires more time for the build to complete (it's faster to build on an existing server than to launch a new server and kill old ones). We've all heard of the big companies having the famous "push to build" button (companies like Twilio, Etsy, etc.) but it seems that they all have custom implementations of this. I'm not talking about a simple ssh-loop, clusterssh, or even an mcollective - I preferably want something with a nice simple interface that allows me to specify something like a RightScript or a Scalr script to run on a set of servers with a specific role, and it builds them sequentially. Does any one know of easy ways to get this done, or is this a candidate for a new open source project?

  Read the article

• creating cookbooks and roles with out chef-server

  - by Josh Nankin

  I want to run: knife role create blah I use chef-solo and don't need knife to connect to a server. I just would like to run these commands for helping me prepopulate the files quickly. Everytime I run of these commands it attempts to connect to a server. This does not happen for knife cookbook create blah Double-ewe tee eff. Update: I've noticed this is the case for databags and environments as well. I've read elsewhere that knife is primarily intended for use with the chef-server API, but it seems ridiculous that something like this can't be done. It just needs to save the darn file.

  Read the article

• apache spawning too many processes despite maxclient and other constraints

  - by Josh Nankin

  Here are my MPM constraints: StartServers 10 MinSpareServers 10 MaxSpareServers 10 MaxClients 10 MaxRequestsPerChild 2000 However despite this, I have over 20 apache processes running currently, and in the past hour or two there have been as many as 40-50. Shouldn't the MaxClient and MaxSpareServers keep the number of processes under control (i.e. about 10)? Is there something I'm missing?

  Read the article

• Windows SMTP Server Outbound IP

  - by Josh

  I have a Windows 2008 server that has three IP bound to the NIC. I can select which IP Windows SMTP listens to, but I want to also set the IP address used when mail is sent. Where would I set which IP to use when sending email?

  Read the article

• SQL Server 2000, large transaction log, almost empty, performance issue?

  - by Mafu Josh

  For a company that I have been helping troubleshoot their database. In SQL Server 2000, database is about 120 gig. Something caused the transaction log to grow MUCH larger than normal to over 100 gig, some hung transaction that didn't commit or roll back for a few days. That has been resolved and it now stays around 1% full or less, due to its hourly transaction log backups. It IS my understanding that a GROWING transaction log file size can cause performance issues. But what I am a little paranoid about is the size. Although mainly empty, MIGHT it be having a negative effect on performance? But I haven't found any documentation that suggests this is true. I did find this link: http://www.bigresource.com/MS_SQL-Large-Transaction-Log-dramatically-Slows-down-processing-any-idea-why--2ahzP5wK.html but in this post I can't tell if their log was full or empty, and there is not any replies to the post in this link. So I am guessing it is not a problem, anyone know for sure?

  Read the article

• Forward all traffic from one IP to another Ip on OS X

  - by Josh

  This is related to this question I just asked... I have two IP address on my iMac I want to "bridge". I'm not sure what the proper terminology is... here's the situation. My iMac has a firewire connection to my laptop and an ethernet connection to the rest of my office. My laptop has an ip of 192.168.100.2 (on the firewire interface). My iMac has an IP of 192.168.100.1 on the firewire interface, and two IPs, 10.1.0.6 and 10.1.0.7, on it's ethernet interface. If I wanted to forward all traffic coming in from 192.168.100.2 on my OS X machine to go out on IP 10.1.0.7, and vice-versa, can this be done? I assume I would use the ipfw command. Essentially I want to "bridge" the firewire network to the ethernet network so my laptop can see all the machines on the 10.1 network, and all those machines can see my laptop at 10.1.0.7. Is this possible?

  Read the article

• Suggestions for someone wanting to become a Laptop Reseller

  - by Josh B.

  First of all, to give you a little background... I have had my Microsoft A+ for several years now. I used to run a small business repairing Xbox 360 consoles and I am currently a Network Engineer for a company in Ohio. I definitely know my way around a computer. I miss running a small business on the side and I'd like to get something going again. There is a really high demand in my area for Laptops and I was thinking about starting a small Laptop store out of my house. What is the best way to do this? I was assuming that the best way would be to buy barebones systems and build them yourself. If this is the best method, I would be very interested in any resources to get parts and such. Apparently Laptop parts aren't the easiest thing to come by (especially at a good price). Does anyone have any suggestions about how to get something like this going?

  Read the article

• Map specific keys in emacs - Ubuntu

  - by Josh

  On my Mac, I have remapped the capslock key to be another Ctrl, and the key to the right of control to be M (meta?). It was real easy, the capslock was in sys prefs, and the M key was a pref in terminal. I cannot figure out how to do it on my Ubuntu 10.10 computer though. There was no remap capslock that I could find under any of the three keyboard pref menu items, and there are no prefs under the terminal that I can find. Can someone advise? I want the windows key on the keyboard to be M, if that matters. tl;dr; Ubuntu 10.10: Map capslock as Ctrl and Windows key as Meta (emacs) Thanks! EDIT: Found Capslock under System - Prefs - Keyboard - Layouts - USA - Options - Ctrl Key Position - Make CapsLock an additional Ctrl

  Read the article

• Verizon FiOS Speed concerns

  - by Josh K

  I'm working on getting a separate internet connection to run out and I was looking into available options. FiOS claims to offer 25Mb up / 25 Mb down as a maximum rate. Do they have listed minimum rates? Is there anything with fiber I should be concerned about? Special hardware, special routers, availability concerns?

  Read the article

• How can I use HAproxy with SSL and get X-Forwarded-For headers AND tell PHP that SSL is in use?

  - by Josh

  I have the following setup: (internet) ---> [ pfSense Box ] /-> [ Apache / PHP server ] [running HAproxy] --+--> [ Apache / PHP server ] +--> [ Apache / PHP server ] \-> [ Apache / PHP server ] For HTTP requests this works great, requests are distributed to my Apache servers just fine. For SSL requests, I had HAproxy distributing the requests using TCP load balancing, and it worked however since HAproxy didn't act as a proxy, it didn't add the X-Forwarded-For HTTP header, and the Apache / PHP servers didn't know the client's real IP address. So, I added stunnel in front of HAproxy, reading that stunnel could add the X-Forwarded-For HTTP header. However, the package which I could install into pfSense does not add this header... also, this apparently kills my ability to use KeepAlive requests, which I would really like to keep. But the biggest issue which killed that idea was that stunnel converted the HTTPS requests into plain HTTP requests, so PHP didn't know that SSL was enabled and tried to redirect to the SSL site. How can I use HAproxy to load balance across a number of SSL servers, allowing those servers to both know the client's IP address and know that SSL is in use? And if possible, how can I do it on my pfSense server? Or should I drop all this and just use nginx?

  Read the article

• How can I avoid my web browser from redirecting to localhost using WAMP in Windows7?

  - by Josh

  I'm currently using Windows 7 with WAMP to try and work on some software, but my web browsers will not accept cookies from the "localhost" domain. I tried creating a few bogus domains in my hosts file by pointing them to 127.0.0.1 but when I type them in I am automatically redirected back to localhost. I have also configured virtualhosts in apache to correspond with the domains I added to the hosts file and it still redirects back to localhost. Is there anything special I must do on Windows 7 to get around this localhost redirect? Thanks for looking :) I'll include my host file here: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost 127.0.0.1 magento.localhost.com www.localhost.com Thanks for looking :)

  Read the article

• High load on a nagios server -- How many service checks for a nagios server is too many?

  - by Josh

  I have a nagios server running Ubuntu with a 2.0 GHz Intel Processor, a RAID10 array, and 400 MB of RAM. It monitors a total of 42 services across 8 hosts, most of which are checked using the check_http plugin even 5 minutes, some every minute. Recently the load on the nagios server has been above 4, often as high as 6. The server also runs cacti, gathering statistics every minute for 6 hosts. I wonder, how many services should hardware like this be able to handle? Is the load so high because I am pushing the limits of the hardware, or should this hardware be able to handle 42 service checks plus cacti? If the hardware is inadequate, should I look to add more RAM, more cores, or faster cores? What hardware / service checks are others running?

  Read the article

• Slow connection to Linux MySQL from Windows only (XAMPP)

  - by Josh

  I'm having a problem with a PHP project (using Kohana 3.2 framework) on my Windows 7 64-bit machine connecting to the database. The development database is stored on a Ubuntu Linux server on the local network. Other development machines running OSX and Linux are connecting fine. There are no other Windows development machines to test with. I can access MySQL fine using MySQL Workbench, and other projects (which I believe to be less database heavy) run mostly ok, only occasionally getting timeout messages. I'm constantly getting Maximum execution time of 30 seconds exceeded when functions such as mysql_query() are run in this particular project. Specifically, the Kohana file where the timeout occurs is MODPATH\database\classes\kohana\database\mysql.php [ 186 ]. My local set-up is: Windows 7 Professional 64bit XAMPP 1.7.7 (PHP 5.3.8) The output of uname -a of the Linux server is: Linux peach 2.6.38-11-server #50-Ubuntu SMP Mon Sep 12 21:34:27 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux I've tried the following, with no success: Disabling Windows firewall Switching between using a persistant and normal connection In my.cnf, adding skip-name-resolve Increasing wait_timeout Enabling bind-address I've run out of ideas now, and have no idea how to debug an odd issue like this. Has anyone come across this before, or have any idea how I could find the root of the issue, or what might be the problem?

  Read the article

• Does NTFS performance degrade significantly in volumes larger than five or six TB?

  - by Josh Yeager

  One of my customers is planning to set up a new document store, which will probably grow by 1-2TB per year. One of my co-workers says that Windows performance is extremely bad if it has a single NTFS volume that is bigger than five or six TB. He thinks that we need to set up their system with multiple volumes so that no single volume will exceed that limit. Is this a real problem? Does Windows or NTFS slow down when the volume size reaches several terabytes? Or is it possible to create a single volume of 10 or more TB?

  Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >