Search Results

Search found 11482 results on 460 pages for 'portable device'.

Page 15/460 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

  • KDE Device Notifier and mounted volumes ownership and permissions

    - by nunomaltez
    Hi, When I plug an USB pen to my PC and mount the device using KDE's Device Notifier, the mounted device is owned by my user, who has write permissions. However, when I connect a USB harddisk and mount a partition in the same way, the mounted device is owned by root, and since the owner is the only one with write permissions I can't write to the disk. How do I configure the device notifier's actions to mount the HD with my user as owner, just like it mounts the USB pen? I'm using Fedora 9.

    Read the article

  • Ralink RT3060 wireless device configuration on ubuntu 12.04

    - by Stephan
    concerning How do I get a Ralink RT3060 wireless card working? I'm running Ubuntu 12.04 with a 'LWPX07 Edimax EW-7711In 150M 1T1R WL PCI Card' which has a rt3060 chip. Out of the box the card is recognized as rt2800sta. I tried solution one, that didn't work. Still the card connects to the wireless network, but it seems to slow to load any pages. Then I tried solution 2, but then the network-manager doesn't see any wireless device. $ iwconfig lo no wireless extensions. ra0 Ralink STA Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. $ lsmod Module Size Used by rt3562sta 882296 0 $ lspci -v 05:02.0 Network controller: Ralink corp. RT3060 Wireless 802.11n 1T/1R Subsystem: Edimax Computer Co. Device 7711 Flags: bus master, slow devsel, latency 64, IRQ 23 Memory at ff9f0000 (32-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: rt2860 Kernel modules: rt3562sta, rt2800pci Am I missing a configuration step? How do I tell the network card which driver to use? Thanks in advance Stephan I found the problem. As described in stevens blog http://steveswinsburg.wordpress.com/2011/03/12/how-to-install-a-d-link-dwa-525-wireless-network-card-in-ubuntu-10-04/ sudo su make && make install "You need to use ‘sudo su’ and not just ‘sudo’ so it creates the directories properly." That is the problem with the solution describe above.

    Read the article

  • How can I hard reset a USB device?

    - by Cory
    I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on superuser.com as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

    Read the article

  • Clipping polygons in XNA with stencil (not using spritebatch)

    - by Blau
    The problem... i'm drawing polygons, in this case boxes, and i want clip children polygons with its parent's client area. // Class Region public void Render(GraphicsDevice Device, Camera Camera) { int StencilLevel = 0; Device.Clear( ClearOptions.Stencil, Vector4.Zero, 0, StencilLevel ); Render( Device, Camera, StencilLevel ); } private void Render(GraphicsDevice Device, Camera Camera, int StencilLevel) { Device.SamplerStates[0] = this.SamplerState; Device.Textures[0] = this.Texture; Device.RasterizerState = RasterizerState.CullNone; Device.BlendState = BlendState.AlphaBlend; Device.DepthStencilState = DepthStencilState.Default; Effect.Prepare(this, Camera ); Device.DepthStencilState = GlobalContext.GraphicsStates.IncMask; Device.ReferenceStencil = StencilLevel; foreach ( EffectPass pass in Effect.Techniques[Technique].Passes ) { pass.Apply( ); Device.DrawUserIndexedPrimitives<VertexPositionColorTexture>( PrimitiveType.TriangleList, VertexData, 0, VertexData.Length, IndexData, 0, PrimitiveCount ); } foreach ( Region child in ChildrenRegions ) { child.Render( Device, Camera, StencilLevel + 1 ); } Effect.Prepare( this, Camera ); // This does not works Device.BlendState = GlobalContext.GraphicsStates.NoWriteColor; Device.DepthStencilState = GlobalContext.GraphicsStates.DecMask; Device.ReferenceStencil = StencilLevel; // This should be +1, but in that case the last drrawed is blue and overlap all foreach ( EffectPass pass in Effect.Techniques[Technique].Passes ) { pass.Apply( ); Device.DrawUserIndexedPrimitives<VertexPositionColorTexture>( PrimitiveType.TriangleList, VertexData, 0, VertexData.Length, IndexData, 0, PrimitiveCount ); } } public static class GraphicsStates { public static BlendState NoWriteColor = new BlendState( ) { ColorSourceBlend = Blend.One, AlphaSourceBlend = Blend.One, ColorDestinationBlend = Blend.InverseSourceAlpha, AlphaDestinationBlend = Blend.InverseSourceAlpha, ColorWriteChannels1 = ColorWriteChannels.None }; public static DepthStencilState IncMask = new DepthStencilState( ) { StencilEnable = true, StencilFunction = CompareFunction.Equal, StencilPass = StencilOperation.IncrementSaturation, }; public static DepthStencilState DecMask = new DepthStencilState( ) { StencilEnable = true, StencilFunction = CompareFunction.Equal, StencilPass = StencilOperation.DecrementSaturation, }; } How can achieve this? EDIT: I've just relized that the NoWriteColors.ColorWriteChannels1 should be NoWriteColors.ColorWriteChannels. :) Now it's clipping right. Any other approach?

    Read the article

  • Displaying device contacts with an indication that the contact is registered to the app

    - by Prasanna Aarthi
    We are developing a mobile app that needs to pick up device contacts, display them and indicate if the contact has already registered with this app. We have our DB in the server and the app fetches data using web services. What will be the best approach to implement the above scenario taking performance into consideration. Option 1: Every time user opens the app,fetch the contacts and send the list of email addresses to the server, check with the registered email ids and return the list of registered users in the contact list. In this approach whenever user opens the particular page, he needs to wait for few seconds to load data, but the contacts will be the latest from the device. Option 2: First time when the user opens the app, fetch contacts ,send the entire list of contacts and save it in the DB, retrieve list of registered users in the contacts then save this to local DB. From now on, data will be fetched from local DB and displayed. When a new user registers in the app, again check with records in central DB and send list of new users who are in your contacts that have registered to your app. This list will be added to local DB. and the process continues. In this case the new contacts added by user will not be updated in the app but retrieval and display of records would be quick. What would be the correct approach? In case there is a better way of doing this, please let me know.

    Read the article

  • Microsoft IntelliMouse episodic pauses

    - by Rob Hills
    I have a Microsoft IntelliMouse connected via USB to a computer (directly, NOT via hub) currently running Ubuntu 11.10, but this problem also existed before we upgraded from 10.10. Every now and then (apparently randomly) the computer "pauses" for anything up to a few seconds. This usually occurs after a mouse movement and during the pause, the computer is completely unresponsive to mouse or keyboard. lsusb shows: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 0409:0058 NEC Corp. HighSpeed Hub Bus 001 Device 004: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 013: ID 045e:001e Microsoft Corp. IntelliMouse Explorer Bus 001 Device 005: ID 04a9:1097 Canon, Inc. PIXMA iP5000 Bus 001 Device 006: ID 0a5c:200a Broadcom Corp. Bluetooth dongle Bus 001 Device 007: ID 0911:1c57 Philips Speech Processing Bus 001 Device 008: ID 04a9:2219 Canon, Inc. CanoScan 9950F so the mouse appears to be correctly identified. Syslog episodically shows the following sequence: Jan 15 11:48:32 kayes-computer kernel: [10588.512036] usb 3-1: USB disconnect, device number 10 Jan 15 11:48:33 kayes-computer kernel: [10589.248026] usb 3-1: new low speed USB device number 11 using uhci_hcd Jan 15 11:48:33 kayes-computer mtp-probe: checking bus 3, device 11: "/sys/devices/pci0000:00/0000:00:1d.1/usb3/3-1" Jan 15 11:48:33 kayes-computer kernel: [10589.448596] input: Microsoft Microsoft IntelliMouse® Explorer as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input11 Jan 15 11:48:33 kayes-computer kernel: [10589.448706] generic-usb 0003:045E:001E.000B: input,hidraw0: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse® Explorer] on usb-0000:00:1d.1-1/input0 Jan 15 11:48:33 kayes-computer mtp-probe: bus: 3, device: 11 was not an MTP device though I can't confirm if these are directly associated with the "pauses". Any thoughts on what might be causing this or what else I can do to diagnose the problem?

    Read the article

  • ubuntu 10.04: boot error for custom compiled kernel - gave up wating for root device

    - by atharva
    Hi, I have installed lucid on my Lenevo Laptop (Y 410 series , x86 platoform) and it is working fine. Now I have compiled kernel 2.6.37 from the downloaded from the kernel tree. I followed usual procedure of compileing kernel (make menuconfig,make. make modules etc). Then I created the initrd image using mkinitramfs and updated my grub using upadate grub command. Update-grub detects the initrd image of the compiled kernel. However when I boot from this kernel it gives me following error: Gave up waiting for root device. Common problems: -Boot args (cat /proc/cmdline) -Check rootdelay= (did the system wait long enough?) -Check root= (did the system wait for the right device?) -Missing modules (cat /proc/modules; ls /dev) ALERT! root=UUID=/... does not exist and then it falls onto initramfs prompt. I have tried following solutions discussed in different ubuntu forums: 1. disable uuid and point root=/dev/sda8 (sda8 is where my kernele image resides (both default kernel and compiled one) from /etc/default/grub 2. compile kernel using CONFIG_DEVTMPFS=y suggested here Still I am unable to boot from the compile kernel. Could someone please suggest me the solution ?

    Read the article

  • Unable to create suitable graphics device?

    - by kraze
    I've been following the Eye of the Dragon tutorial, which is basicly a guide to making a 2D RPG game, obviously. I recently finished the tutorial about making pop up screens in the menu and changed the screen to load as a full screen. Whenever I try and load the game it just goes black and my mouse sits there. I cannot change out of it other then with CtrlAltDel. Once i do that it says No suitable graphics card found, unable to create graphics device. I read somewhere about XNA not allowing more then one screen when any one of them is full screen. but it wasnt very informative. Anyone have any ideas whats going on and/or how to fix this? Just incase if this helps this is the code for the graphics device: public Game1() { graphics = new GraphicsDeviceManager(this); graphics.PreferredBackBufferWidth = 900; graphics.PreferredBackBufferHeight = 768; graphics.IsFullScreen = true; this.Window.Title = "Eyes of the Dragon"; Content.RootDirectory = "Content"; }

    Read the article

  • Ubuntu 10.04: boot error for custom compiled kernel - gave up waiting for root device

    - by atharva
    I have installed lucid on my Lenevo Laptop (Y 410 series , x86 platform) and it is working fine. Now I have compiled kernel 2.6.37 downloaded from the kernel tree. I followed usual procedure of compiling kernel (make menuconfig, make, make modules etc). Then I created the initrd image using mkinitramfs and updated my grub using update-grub command. update-grub detects the initrd image of the compiled kernel. However when I boot from this kernel it gives me following error: Gave up waiting for root device. Common problems: -Boot args (cat /proc/cmdline) -Check rootdelay= (did the system wait long enough?) -Check root= (did the system wait for the right device?) -Missing modules (cat /proc/modules; ls /dev) ALERT! root=UUID=/... does not exist and then it falls onto initramfs prompt. I have tried following solutions discussed in different Ubuntu forums: disable uuid and point root=/dev/sda8 (sda8 is where my kernel image resides (both default kernel and compiled one) from /etc/default/grub compile kernel using CONFIG_DEVTMPFS=y suggested here Still I am unable to boot from the compile kernel. Could someone please suggest me the solution?

    Read the article

  • Samba share external USB device

    - by bioShark
    I managed to share stuff from my Ubuntu 12.04 to my private network, and the data is visible from a Windows machine. I even shared a hdd that has windows on it. So everything seems to work fine. When I want to share a mounted device (USB pen drive, USB HDD... etc) however, I get from the Windows machine: Access denied on file \... I realize that this is due to the missing rights on the mounted folder. By default a mounted folder gets the equivalent of 700 : drwx------, and the owner myself. But, I can't seem to change the rights on the external device... they remain 700. Is there a special trick I need to do in order to share NTFS mounted usb devices? Thanks P.S. from this Question I see that NTFS devices can not be shared....is this true? It's a bit strange, because I have in my PC 2 HDD's with 3 NTFS partitions, and I can share them without a problem.

    Read the article

  • How to show AdMob ads in real iPhone device?

    - by iPhoney
    I want to integrate AdMob ads in my iPhone app. I'm using IB way to add the view and follow AdMob's pdf guide: 1. Add AdMob group(AdMobView.h,AdMobDelegateProtocol.h,libAdMob.a) 2. Add required frameworks(AudioToolbox,MediaPlayer,MessageUI,QuartzCore) 3. Add TouchJSON group 4. Add IBSupport group(AdViewController.h,AdViewController.m) 5. Add a 320*48 UIView in IB, add NSObject and change its class to AdViewController, link AdViewController's view to the 320*48 UIView and link AdViewController's viewController to current view controller. Now the iPhone simulator can show ads from AdMob, but when I test it on real device, I get the error "AdMob: Did fail to receive ad". I've tried to add test device's UDID to testDevices array, but still get the same error. - (NSArray *)testDevices { return [NSArray arrayWithObjects: ADMOB_SIMULATOR_ID, DEVICE_UDID, nil]; } Is there any problem in the above steps? Does anybody know why can't I get the ads in real device? By the way, what should be changed to build for real for-sale app, not just for test?

    Read the article

  • The Best Application Launchers and Docks for Organizing Your Desktop

    - by Lori Kaufman
    Is your desktop so cluttered you can’t find anything? Is your Start menu so long you have to scroll to see what programs are there? If so, you probably need an application launcher to organize your desktop and make your life easier. We’ve created a list of many useful application launchers in different forms. You can choose from dock programs, portable application launchers, Start menu and Taskbar replacements, and keyboard-oriented launchers. HTG Explains: What Is RSS and How Can I Benefit From Using It? HTG Explains: Why You Only Have to Wipe a Disk Once to Erase It HTG Explains: Learn How Websites Are Tracking You Online

    Read the article

  • Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

    - by jgottula
    I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

    Read the article

  • A real noob question

    - by Jaymz
    I have a Hp mini netbook that has been wiped clean, there is nothing other than the bios on it, it has no DVD and I don't have an external DVD. I can change the boot order to boot from a usb device. I have downloaded ubuntu-12.04.1-desktop-i386 I have one of these http://www.kikatek.com/P100600/34609-IOMEGA-250gb-Select-Portable-HDD-2-5-USB?source=froogle currently formatted to NTFS but I can format to exFAT I have tried Linuxlive USB creator, all that managed to do was dual boot the desktop pc that I'm working off, and when booting on the wiped clean netbook, just left me with a black screen with a blinking cursor I have also tried Unetbootin, this managed to change my 'My Computer' icon to Install Ubuntu (C:) and now again, my desktop pc dual boots with the Wubi software, the Unetbootin, wouldn't let me select my external drive to write to Please I'm a complete idiot, i need a super idiots guide to doing this Regards Jaymz

    Read the article

  • raid md device is not remove from memory, how to overcome this problem

    - by santhosha
    i create raid 10 , i removed two arrays form md11 one by one , after that i going to editing the contents those are mounted ( it will be not responding stage), after i try for remove arrays those are left it is shows device or resource busy ( is not removed from memory). i try to terminate process this is also not work, i absorve from 4 days resync will be 8.0% it can not modifying. cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec mdadm -D /dev/md11 /dev/md11: Version : 00.90.03 Creation Time : Sun Jan 16 16:20:01 2011 Raid Level : raid10 Array Size : 286743936 (273.46 GiB 293.63 GB) Device Size : 143371968 (136.73 GiB 146.81 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 11 Persistence : Superblock is persistent Update Time : Sun Jan 16 16:56:07 2011 State : active, degraded, resyncing Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K Rebuild Status : 8% complete UUID : 5e124ea4:79a01181:dc4110d3:a48576ea Events : 0.23 Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 4 8 145 2 faulty spare rebuilding /dev/sdj1 3 8 65 3 active sync /dev/sde1 umount /dev/md11 umount: /dev/md11: not mounted mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 kill -9 2128 kill -9 5018 kill -9 27605 kill -9 30562 kill -3 30591 mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec

    Read the article

  • What device can create wireless network while connecting to an ethernet router

    - by Nicolo
    Hi, I have access to an ethernet port of a wireless router. I simply connect my laptop to it via an ethernet cable. There are a total of four such ports on the wireless router. Now I want to connect a device (a wireless access point? wireless bridge? wireless switch?) via an ethernet cable to one of the other ethernet ports of the router. I want this device to act as a kind of wireless switch - it should "split" the ethernet connection coming from the router to two or more computers that connect to this device via a wireless. Basically, I have a wireless router with its wireless function switched off. I don't know the password for that router so can't activate the wireless function. Don't know the password of the ISP either. The only thing I can do is to connect via ethernet cable to the wireless router and this does not require a password. Now I want to use that connection and build a wireless upon it. What kind of device do I need? I am not really very well informed about network management and find the descriptions "wireless access point", "wireless bridge", "wireless switch" confusing. I know what an ethernet switch is - what I need is a device which would do the same but by allowing the clients to connect to it via a wireless. What kind of device would do that? Any recommendations about specific products?

    Read the article

  • Usb device not working properly on a Thinkpad T60

    - by Xavierjazz
    I have just started getting a message that a USB device is not working properly. This is on a new Thinkpad T60 running Windows XP Professional SP3. I have had all devices attached for about 10 days or so. When I go to device manager there is no sign of a problem: everything is working correctly. I am unable to find out which device it is. I searched this forum but the only reference I found was to older computers which may not be Usb2 capable. This is not my problem. Any ideas? Thanks. EDIT: I realized I had a harddrive attached but turned off. Although I could not track down any error messages except the balloon that came up, I have disconnected it and, so far, no messages. We'll see over the next day or two, but this may be the problem. Thanks EDIT: This has not solved the problem. I get the message that one of the USB devices has malfunctioned and it points to "USB root hub (2 ports)" and shows an unused port and an unknown device. However, when I check my device manager, it says that there are no problems, everything is working as it should. ?? EDIT: I now found the event log view and there are 2 types of error messages. They do not relate to the time that I get the balloon. 2 of the 3 are "Ati2mtag" errors and the third is "System Control Manager". Are these related to my problem, and the balloon just pops up randomly? EDIT: well, I'm still having the problem, and have narrowed it down to a malfunctioning device. Thanks to all.

    Read the article

  • Maintaining "Portability" Between Linux and Windows 7

    - by lokheart
    I am using the following ways in my office's Windows 7 machine to maintain my "portabilibity" when disaster strikes and I need to switch computer while I have no luxury of time for reinstalling all my program to the new PC. a majority of programs I used are portable, mostly from portableapp.com, like notepad+, GIMP, even R, I extract them and store them in a folder in My document, in a structure similar to the default portableapp installation when they are installed to a thumbdrive only a few software that portable version is not available and I will install them as usual all of my working files are stored in a folder in My document I regularly backup them all using syncback, because this program can keep versioning of my backup, and the backup is stored in a portable drive. One day I need to switch my computer and the operation is relative simple for me: I just move the two folders mentioned above into the my document folder of the new PC, install those few "non-portable" program in it, and this is almost done, some minor hiccups can be solved by reinstalling the portableapp into the drive. Overall speaking it is a smooth process. I would like to maintain the same degree of "portability" in my home Linux desktop (Ubuntu or Mint, I'm still deciding), that is, if my Linux crash and I need to reinstall it again. All I need to do is the move the two folder back to the new Linux, and most of my work will be almost ready to be worked on again. But I don't know how to find a Linux-alternative of portableapps. Being a newer to Linux, can anyone tell me whether this is possible in Linux?

    Read the article

  • Using udev to create a character device based on a driver being loaded

    - by SteveCB
    I'm in the process of setting up RAID monitoring for a number of Dell servers that use the PERC 6i integrated card. We're using Nagios at present and the check_megasasctl plugin seems to fit the bill. However, the plugin relies upon the existence of: /dev/megaraid_sas_ioctl_node This device node doesn't exist by default, you have to create it by hand using something like: mknod /dev/megaraid_sas_ioctl_node c 253 0 Now, to make the existence of this device node persistent across reboots, I thought I could write a udev rule, but as usual, I'm missing something. I thought I could create a file such as /etc/udev/rules.d/10-local/rules that contained: DRIVER=="megasas" NAME="megaraid_sas_ioctl_node" MODE="0600" But this doesn't work - no device node after a reboot. Dmesg output indicates the megasas driver is loaded and functional: megasas: 00.00.04.01-RH1 Thu July 10 09:41:51 PST 2008 megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 1:slot 0:func 0 megasas: FW now in Ready state Further, I don't see any means to instruct udev on which type of device node to create: character or block. I suspect I'm failing to understand exactly how udev is meant to work. I realise I could just cheat and run MegaCLI in /etc/rc.local, redirecting output to /dev/null; it creates the megaraid_sas_ioctl_node device node as part of its execution. I just thought using udev rules would be a) cleaner and b) a useful learning exercise. Perhaps I should just dump the above mknod command in /etc/rc.local... So how do I get udev to create the /dev/megaraid_sas_ioctl_node device node based on the presence of the megasas driver? Cheers Steve

    Read the article

  • Windows VirtualBox failed to attach USB device to Linux Guest

    - by joltmode
    I have Windows 7 64bit Host system, and I am using VirtualBox 4.1.18 (r78361). I have an Arch Linux Guest OS. I have installed VirtualBox Extension Pack (to enable USB2 support) and added my USB device filter to VM. I have also installed the Guest Additions provided by Arch: virtualbox-archlinux-additions (but I have no idea whether it's actually needed for my environment). I can see my USB device from VirtualBox Devices menu. Whenever I am trying to access it, I end up with: Failed to attach the USB device Kingston DT 100 G2 [0100] to the virtual machine Archlinux. USB device 'Kingston DT 100 G2' with UUID {a836ec33-0f41-4ca7-a31d-09cceaf5d173} is busy with a previous request. Please try again later. Details ? Result Code:    E_INVALIDARG (0x80070057) Component:      HostUSBDevice Interface:      IHostUSBDevice {173b4b44-d268-4334-a00d-b6521c9a740a} Callee:         IConsole {1968b7d3-e3bf-4ceb-99e0-cb7c913317bb} From what I have googled, most guides shows how to solve this the other way around - Linux Host to Windows Guest. How do I resolve this? Update I have tried to Eject (virtually, not physically) the device from my Windows Host system and then try to access the Device from Guest. Same error.

    Read the article

  • Removing a device in "removed" state from Linux software RAID array

    - by Sahasranaman MS
    My workstation has two disks(/dev/sd[ab]), both with similar partitioning. /dev/sdb failed, and cat /proc/mdstat stopped showing the second sdb partition. I ran mdadm --fail and mdadm --remove for all partitions from the failed disk on the arrays that use them, although all such commands failed with mdadm: set device faulty failed for /dev/sdb2: No such device mdadm: hot remove failed for /dev/sdb2: No such device or address Then I hot swapped the failed disk, partitioned the new disk and added the partitions to the respective arrays. All arrays got rebuilt properly except one, because in /dev/md2, the failed disk doesn't seem to have been removed from the array properly. Because of this, the new partition keeps getting added as a spare to the partition, and its status remains degraded. Here's what mdadm --detail /dev/md2 shows: [root@ldmohanr ~]# mdadm --detail /dev/md2 /dev/md2: Version : 1.1 Creation Time : Tue Dec 27 22:55:14 2011 Raid Level : raid1 Array Size : 52427708 (50.00 GiB 53.69 GB) Used Dev Size : 52427708 (50.00 GiB 53.69 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Intent Bitmap : Internal Update Time : Fri Nov 23 14:59:56 2012 State : active, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Name : ldmohanr.net:2 (local to host ldmohanr.net) UUID : 4483f95d:e485207a:b43c9af2:c37c6df1 Events : 5912611 Number Major Minor RaidDevice State 0 8 2 0 active sync /dev/sda2 1 0 0 1 removed 2 8 18 - spare /dev/sdb2 To remove a disk, mdadm needs a device filename, which was /dev/sdb2 originally, but that no longer refers to device number 1. I need help with removing device number 1 with 'removed' status and making /dev/sdb2 active.

    Read the article

  • Getting DirectoryNotFoundException when trying to Connect to Device with CoreCon API

    - by ageektrapped
    I'm trying to use the CoreCon API in Visual Studio 2008 to programmatically launch device emulators. When I call device.Connect(), I inexplicably get a DirectoryNotFoundException. I get it if I try it in PowerShell or in C# Console Application. Here's the code I'm using: static void Main(string[] args) { DatastoreManager dm = new DatastoreManager(1033); Collection<Platform> platforms = dm.GetPlatforms(); foreach (var p in platforms) { Console.WriteLine("{0} {1}", p.Name, p.Id); } Platform platform = platforms[3]; Console.WriteLine("Selected {0}", platform.Name); Device device = platform.GetDevices()[0]; device.Connect(); Console.WriteLine("Device Connected"); SystemInfo info = device.GetSystemInfo(); Console.WriteLine("System OS Version:{0}.{1}.{2}", info.OSMajor, info.OSMinor, info.OSBuildNo); Console.ReadLine(); } My question: Does anyone know why I'm getting this error? I'm running this on WinXP 32-bit, plain jane Visual Studio 2008 Pro. I imagine it's some config issue since I can't do it from a Console app or PowerShell. Here's the stack trace as requested: System.IO.DirectoryNotFoundException was unhandled Message="The system cannot find the path specified.\r\n" Source="Device Connection Manager" StackTrace: at Microsoft.VisualStudio.DeviceConnectivity.Interop.ConManServerClass.ConnectDevice() at Microsoft.SmartDevice.Connectivity.Device.Connect() at ConsoleApplication1.Program.Main(String[] args) in C:\Documents and Settings\Thomas\Local Settings\Application Data\Temporary Projects\ConsoleApplication1\Program.cs:line 23 at System.AppDomain._nExecuteAssembly(Assembly assembly, String[] args) at System.AppDomain.ExecuteAssembly(String assemblyFile, Evidence assemblySecurity, String[] args) at Microsoft.VisualStudio.HostingProcess.HostProc.RunUsersAssembly() at System.Threading.ThreadHelper.ThreadStart_Context(Object state) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Threading.ThreadHelper.ThreadStart() InnerException:

    Read the article

  • How to connect to bluetoothbee device using j2me?

    - by user1500412
    I developed a simple bluetooth connection application in j2me. I try it on emulator, both server and client can found each other, but when I deploy the application to blackberry mobile phone and connect to a bluetoothbee device it says service search no records. What could it be possibly wrong? is it j2me can not find a service in bluetoothbee? The j2me itself succeed to found the bluetoothbee device, but why it can not find the service? My code is below. What I don't understand is the UUID? how to set UUID for unknown source? since I didn't know the UUID for the bluetoothbee device. class SearchingDevice extends Canvas implements Runnable,CommandListener,DiscoveryListener{ //...... public SearchingDevice(MenuUtama midlet, Display display){ this.display = display; this.midlet = midlet; t = new Thread(this); t.start(); timer = new Timer(); task = new TestTimerTask(); /*--------------------Device List------------------------------*/ select = new Command("Pilih",Command.OK,0); back = new Command("Kembali",Command.BACK,0); btDevice = new List("Pilih Device",Choice.IMPLICIT); btDevice.addCommand(select); btDevice.addCommand(back); btDevice.setCommandListener(this); /*------------------Input Form---------------------------------*/ formInput = new Form("Form Input"); nama = new TextField("Nama","",50,TextField.ANY); umur = new TextField("Umur","",50,TextField.ANY); measure = new Command("Ukur",Command.SCREEN,0); gender = new ChoiceGroup("Jenis Kelamin",Choice.EXCLUSIVE); formInput.addCommand(back); formInput.addCommand(measure); gender.append("Pria", null); gender.append("Wanita", null); formInput.append(nama); formInput.append(umur); formInput.append(gender); formInput.setCommandListener(this); /*---------------------------------------------------------------*/ findDevice(); } /*----------------Gambar screen searching device---------------------------------*/ protected void paint(Graphics g) { g.setColor(0,0,0); g.fillRect(0, 0, getWidth(), getHeight()); g.setColor(255,255,255); g.drawString("Mencari Device", 20, 20, Graphics.TOP|Graphics.LEFT); if(this.counter == 1){ g.setColor(255,115,200); g.fillRect(20, 100, 20, 20); } if(this.counter == 2){ g.setColor(255,115,200); g.fillRect(20, 100, 20, 20); g.setColor(100,255,255); g.fillRect(60, 80, 20, 40); } if(this.counter == 3){ g.setColor(255,115,200); g.fillRect(20, 100, 20, 20); g.setColor(100,255,255); g.fillRect(60, 80, 20, 40); g.setColor(255,115,200); g.fillRect(100, 60, 20, 60); } if(this.counter == 4){ g.setColor(255,115,200); g.fillRect(20, 100, 20, 20); g.setColor(100,255,255); g.fillRect(60, 80, 20, 40); g.setColor(255,115,200); g.fillRect(100, 60, 20, 60); g.setColor(100,255,255); g.fillRect(140, 40, 20, 80); //display.callSerially(this); } } /*--------- Running Searching Screen ----------------------------------------------*/ public void run() { while(run){ this.counter++; if(counter > 4){ this.counter = 1; } try { Thread.sleep(1000); } catch (InterruptedException ex) { System.out.println("interrupt"+ex.getMessage()); } repaint(); } } /*-----------------------------cari device bluetooth yang -------------------*/ public void findDevice(){ try { devices = new java.util.Vector(); local = LocalDevice.getLocalDevice(); agent = local.getDiscoveryAgent(); local.setDiscoverable(DiscoveryAgent.GIAC); agent.startInquiry(DiscoveryAgent.GIAC, this); } catch (BluetoothStateException ex) { System.out.println("find device"+ex.getMessage()); } } /*-----------------------------jika device ditemukan--------------------------*/ public void deviceDiscovered(RemoteDevice rd, DeviceClass dc) { devices.addElement(rd); } /*--------------Selesai tes koneksi ke bluetooth server--------------------------*/ public void inquiryCompleted(int param) { switch(param){ case DiscoveryListener.INQUIRY_COMPLETED: //inquiry completed normally if(devices.size()>0){ //at least one device has been found services = new java.util.Vector(); this.findServices((RemoteDevice)devices.elementAt(0)); this.run = false; do_alert("Inquiry completed",4000); }else{ do_alert("No device found in range",4000); } break; case DiscoveryListener.INQUIRY_ERROR: do_alert("Inquiry error",4000); break; case DiscoveryListener.INQUIRY_TERMINATED: do_alert("Inquiry canceled",4000); break; } } /*-------------------------------Cari service bluetooth server----------------------------*/ public void findServices(RemoteDevice device){ try { // int[] attributes = {0x100,0x101,0x102}; UUID[] uuids = new UUID[1]; //alamat server uuids[0] = new UUID("F0E0D0C0B0A000908070605040302010",false); //uuids[0] = new UUID("8841",true); //menyiapkan device lokal local = LocalDevice.getLocalDevice(); agent = local.getDiscoveryAgent(); //mencari service dari server agent.searchServices(null, uuids, device, this); //server = (StreamConnectionNotifies)Connector.open(url.toString()); } catch (BluetoothStateException ex) { // ex.printStackTrace(); System.out.println("Errorx"+ex.getMessage()); } } /*---------------------------Pencarian service selesai------------------------*/ public void serviceSearchCompleted(int transID, int respCode) { switch(respCode){ case DiscoveryListener.SERVICE_SEARCH_COMPLETED: if(currentDevice == devices.size() - 1){ if(services.size() > 0){ this.run = false; display.setCurrent(btDevice); do_alert("Service found",4000); }else{ do_alert("The service was not found",4000); } }else{ currentDevice++; this.findServices((RemoteDevice)devices.elementAt(currentDevice)); } break; case DiscoveryListener.SERVICE_SEARCH_DEVICE_NOT_REACHABLE: do_alert("Device not Reachable",4000); break; case DiscoveryListener.SERVICE_SEARCH_ERROR: do_alert("Service search error",4000); break; case DiscoveryListener.SERVICE_SEARCH_NO_RECORDS: do_alert("No records return",4000); break; case DiscoveryListener.SERVICE_SEARCH_TERMINATED: do_alert("Inquiry canceled",4000); break; } } public void servicesDiscovered(int i, ServiceRecord[] srs) { for(int x=0; x<srs.length;x++) services.addElement(srs[x]); try { btDevice.append(((RemoteDevice)devices.elementAt(currentDevice)).getFriendlyName(false),null); } catch (IOException ex) { System.out.println("service discover"+ex.getMessage()); } } public void do_alert(String msg, int time_out){ if(display.getCurrent() instanceof Alert){ ((Alert)display.getCurrent()).setString(msg); ((Alert)display.getCurrent()).setTimeout(time_out); }else{ Alert alert = new Alert("Bluetooth"); alert.setString(msg); alert.setTimeout(time_out); display.setCurrent(alert); } } private String getData(){ System.out.println("getData"); String cmd=""; try { ServiceRecord service = (ServiceRecord)services.elementAt(btDevice.getSelectedIndex()); String url = service.getConnectionURL(ServiceRecord.NOAUTHENTICATE_NOENCRYPT, false); conn = (StreamConnection)Connector.open(url); DataInputStream in = conn.openDataInputStream(); int i=0; timer.schedule(task, 15000); char c1; while(time){ //while(((c1 = in.readChar())>0) && (c1 != '\n')){ //while(((c1 = in.readChar())>0) ){ c1 = in.readChar(); cmd = cmd + c1; //System.out.println(c1); // } } System.out.print("cmd"+cmd); if(time == false){ in.close(); conn.close(); } } catch (IOException ex) { System.err.println("Cant read data"+ex); } return cmd; } //timer task fungsinya ketika telah mencapai waktu yg dijadwalkan putus koneksi private static class TestTimerTask extends TimerTask{ public TestTimerTask() { } public void run() { time = false; } } }

    Read the article

  • Installing device drivers as part of VS2008 setup application (3 replies)

    A colleague in another department has produced device drivers for some USB devices that I need to communicate with in my VS2008 .Net application, and I'm looking to simplify the installation experience for our users. Currently I just put the driver files onto the CD in a folder, and the Windows Add Hardware Wizard will usually take them through the process. What I would like to do though, is to in...

    Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >