Search Results

Search found 10603 results on 425 pages for 'device emulation'.

Page 150/425 | < Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >

• Degraded RAID5 and no md superblock on one of remaining drive

  - by ark1214

  This is actually on a QNAP TS-509 NAS. The RAID is basically a Linux RAID. The NAS was configured with RAID 5 with 5 drives (/md0 with /dev/sd[abcde]3). At some point, /dev/sde failed and drive was replaced. While rebuilding (and not completed), the NAS rebooted itself and /dev/sdc dropped out of the array. Now the array can't start because essentially 2 drives have dropped out. I disconnected /dev/sde and hoped that /md0 can resume in degraded mode, but no luck.. Further investigation shows that /dev/sdc3 has no md superblock. The data should be good since the array was unable to assemble after /dev/sdc dropped off. All the searches I done showed how to reassemble the array assuming 1 bad drive. But I think I just need to restore the superblock on /dev/sdc3 and that should bring the array up to a degraded mode which will allow me to backup data and then proceed with rebuilding with adding /dev/sde. Any help would be greatly appreciated. mdstat does not show /dev/md0 # cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath] md5 : active raid1 sdd2[2](S) sdc2[3](S) sdb2[1] sda2[0] 530048 blocks [2/2] [UU] md13 : active raid1 sdd4[3] sdc4[2] sdb4[1] sda4[0] 458880 blocks [5/4] [UUUU_] bitmap: 40/57 pages [160KB], 4KB chunk md9 : active raid1 sdd1[3] sdc1[2] sdb1[1] sda1[0] 530048 blocks [5/4] [UUUU_] bitmap: 33/65 pages [132KB], 4KB chunk mdadm show /dev/md0 is still there # mdadm --examine --scan ARRAY /dev/md9 level=raid1 num-devices=5 UUID=271bf0f7:faf1f2c2:967631a4:3c0fa888 ARRAY /dev/md5 level=raid1 num-devices=2 UUID=0d75de26:0759d153:5524b8ea:86a3ee0d spares=2 ARRAY /dev/md0 level=raid5 num-devices=5 UUID=ce3e369b:4ff9ddd2:3639798a:e3889841 ARRAY /dev/md13 level=raid1 num-devices=5 UUID=7384c159:ea48a152:a1cdc8f2:c8d79a9c With /dev/sde removed, here is the mdadm examine output showing sdc3 has no md superblock # mdadm --examine /dev/sda3 /dev/sda3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff0e - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 0 8 3 0 active sync /dev/sda3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdb3 /dev/sdb3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff20 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 1 8 19 1 active sync /dev/sdb3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdc3 mdadm: No md superblock detected on /dev/sdc3. [~] # mdadm --examine /dev/sdd3 /dev/sdd3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff44 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 3 8 51 3 active sync /dev/sdd3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed fdisk output shows /dev/sdc3 partition is still there. [~] # fdisk -l Disk /dev/sdx: 128 MB, 128057344 bytes 8 heads, 32 sectors/track, 977 cylinders Units = cylinders of 256 * 512 = 131072 bytes Device Boot Start End Blocks Id System /dev/sdx1 1 8 1008 83 Linux /dev/sdx2 9 440 55296 83 Linux /dev/sdx3 441 872 55296 83 Linux /dev/sdx4 873 977 13440 5 Extended /dev/sdx5 873 913 5232 83 Linux /dev/sdx6 914 977 8176 83 Linux Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 66 530113+ 83 Linux /dev/sda2 67 132 530145 82 Linux swap / Solaris /dev/sda3 133 182338 1463569695 83 Linux /dev/sda4 182339 182400 498015 83 Linux Disk /dev/sda4: 469 MB, 469893120 bytes 2 heads, 4 sectors/track, 114720 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/sda4 doesn't contain a valid partition table Disk /dev/sdb: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 * 1 66 530113+ 83 Linux /dev/sdb2 67 132 530145 82 Linux swap / Solaris /dev/sdb3 133 182338 1463569695 83 Linux /dev/sdb4 182339 182400 498015 83 Linux Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdc1 1 66 530125 83 Linux /dev/sdc2 67 132 530142 83 Linux /dev/sdc3 133 182338 1463569693 83 Linux /dev/sdc4 182339 182400 498012 83 Linux Disk /dev/sdd: 2000.3 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdd1 1 66 530125 83 Linux /dev/sdd2 67 132 530142 83 Linux /dev/sdd3 133 243138 1951945693 83 Linux /dev/sdd4 243139 243200 498012 83 Linux Disk /dev/md9: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md9 doesn't contain a valid partition table Disk /dev/md5: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md5 doesn't contain a valid partition table

  Read the article

• Virtualbox and Serial Port permissions

  - by Pandincus

  I have a Windows XP Pro SP3 host machine running a Windows XP Pro SP3 guest machine. The host machine has one serial port, COM1, that I need to use in the guest machine. When I add the serial port to the guest machine and try to start it, I get the following error: Failed to start the virtual machine xxx Cannot open host device 'COM1' for read/write access. Check the permissions of that device (VERR_ACCESS_DENIED). Unknown error creating VM (VERR_ACCESS_DENIED). What are some of the things that might be causing this problem? How can I check "permissions" on a serial port?

  Read the article

• SQL Server: Is it possible to prevent SQL Agent from failing a step on error?

  - by franklinkj

  I have a stored procedure that runs custom backups for around 60 SQL servers (mixes 2000 through 2008R2). Occasionally, due to issues outside of my control (backup device inaccessible, network error, etc.) an individual backup on one or two databases will fail. This causes this entire step to fail, which means any subsequent backup commands are not executed and half of the databases on a given server may not be backed up. On the 2005+ boxes I am using TRY/CATCH blocks to manage these problems and continue backing up the remaining databases. On a 2000 server however, for example, I have no way to prevent this error from failing the entire step: Msg 3201, Level 16, State 1, Line 1 Cannot open backup device 'db-diff(\PATH\DB-DIFF-03-16-2010.DIF)'. Operating system error 5(Access is denied.). Msg 3013, Level 16, State 1, Line 1 BACKUP DATABASE is terminating abnormally. I am simply asking if anything like this is possible in SQL 2000 or if I need to go in a completely different direction.

  Read the article

• Building NanoBSD inside a jail

  - by ptomli

  I'm trying to setup a jail to enable building a NanoBSD image. It's actually a jail on top of a NanoBSD install. The problem I have is that I'm unable to mount the md device in order to do the 'build image' part. Is it simply not possible to mount an md device inside a jail, or is there some other knob I need to twiddle? On the host /etc/rc.conf.local jail_enable="YES" jail_mount_enable="YES" jail_list="build" jail_set_hostname_allow="NO" jail_build_hostname="build.vm" jail_build_ip="192.168.0.100" jail_build_rootdir="/mnt/zpool0/jails/build/home" jail_build_devfs_enable="YES" jail_build_devfs_ruleset="devfsrules_jail_build" /etc/devfs.rules [devfsrules_jail_build=5] # nothing Inside the jail [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# sysctl security.jail security.jail.param.cpuset.id: 0 security.jail.param.host.hostid: 0 security.jail.param.host.hostuuid: 64 security.jail.param.host.domainname: 256 security.jail.param.host.hostname: 256 security.jail.param.children.max: 0 security.jail.param.children.cur: 0 security.jail.param.enforce_statfs: 0 security.jail.param.securelevel: 0 security.jail.param.path: 1024 security.jail.param.name: 256 security.jail.param.parent: 0 security.jail.param.jid: 0 security.jail.enforce_statfs: 1 security.jail.mount_allowed: 1 security.jail.chflags_allowed: 1 security.jail.allow_raw_sockets: 0 security.jail.sysvipc_allowed: 0 security.jail.socket_unixiproute_only: 1 security.jail.set_hostname_allowed: 0 security.jail.jail_max_af_ips: 255 security.jail.jailed: 1 [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# mdconfig -l md2 md0 md1 md0 and md1 are the ramdisks of the host. bsdlabel looks sensible [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# bsdlabel /dev/md2s1 # /dev/md2s1: 8 partitions: # size offset fstype [fsize bsize bps/cpg] a: 1012016 16 4.2BSD 0 0 0 c: 1012032 0 unused 0 0 # "raw" part, don't edit newfs runs ok [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# newfs -U /dev/md2s1a /dev/md2s1a: 494.1MB (1012016 sectors) block size 16384, fragment size 2048 using 4 cylinder groups of 123.55MB, 7907 blks, 15872 inodes. with soft updates super-block backups (for fsck -b #) at: 160, 253184, 506208, 759232 mount fails [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# mount /dev/md2s1a _.mnt/ mount: /dev/md2s1a : Operation not permitted UPDATE: One of my colleagues pointed out There are some file systems types that can't be securely mounted within a jail no matter what, like UFS, MSDOFS, EXTFS, XFS, REISERFS, NTFS, etc. because the user mounting it has access to raw storage and can corrupt it in a way that it will panic entire system. From http://www.mail-archive.com/[email protected]/msg160389.html So it seems that the standard nanobsd.sh won't run inside a jail while it uses the md device to build the image. One potential solution I'll try is to chroot from the host into the build jail, rather than jexec a shell.

  Read the article

• Are FC and SAS DAS devices standard enough?

  - by user222182

  Before I ask my questions, here is some background info that may or may not be useful: For the first time I find myself needing a DAS solution. My priority is data through-put in a single direction. I can write large blocks, and I don't need to read at the same time. The server (the data producing device) is not really a typical server, its a very powerful single board computer. As such I have limited options when it comes to the add-in cards I can install since it must use the fairly uncommon interface, XMC. Currently I believe I am limited PCIex8 gen 1 which means that the likely bottle neck for me will be this 16gbps connection. XMC Boards I have found so far offer the following connections: a) Dual 10GBE ethernet controller, total throughput 20gbps b) Dual Quad SAS 2.0 Connectors (SFF-8XXX) HBA (no raid), total throughput 48 gbps c) Dual FC 8gb HBA (no raid), total throughput 16gbps My questions for you guys are: 1) Are SAS and/or FC, and by extension their HBAs, standard enough that I could purchase a Dell or Aberdeen storage server with a raid controller that has external SAS or FC ports and expect that I can connect it to my SAS or FC HBA, be presented with a single volume (if I so configured the storage server), all without having to check for HBA compatibility? 2) On a device like a Dell PowerVault (either DAS or NAS) is there an OS on it to concern myself with, or is it meant to be remotely managed? Is there a local interface in case I cant remotely manage it (i.e. if my single board computer uses an OS not supported by Dell OpenManage). Would this be true of nearly any device which calls itself a DAS? 3) If I purchase some sort of Supermicro storage chassis, installed a raid controller with external connections, is there a nice lightweight OS I can run just for management of the controller? Would I even need an OS since the raid card would be configured pre-boot anyway? 4) It is much easier to buy XMC based 10gigabit ethernet cards (generally dual port). In what ways would I be getting into trouble by using iSCSI as a DAS are direct cabling with SFP+ cables? Thanks in advance

  Read the article

• external SCSI tape drive DAT 72 problem Solaris 10

  - by Hassan

  Hi all, I have solaris 10 sparc running and working very well but i have problem with external SCSI tape drive DAT 72 problem it seems to me the tape drive is manufactured by SUN microsystems when i ran mt -f /dev/rmt/0 status it reveals the following output bash-3.00# mt -f /dev/rmt/0 status /dev/rmt/0: No such file or directory when i ran ls -l it reveals the following output ls -l /dev/rmt/0 lrwxrwxrwx 1 root root 43 Sep 20 2006 /dev/rmt/0 -> ../../devices/pci@8,600000/scsi@1,1/st@3,0: it seems to me everything is okay SCSI cable is connected properly to Tape device and to server as well the tape has SCSI termination dongle as well and connected properly to Tape device as well any ideas would be a great assist Thanks in advance

  Read the article

• Storage (EBS) attached to my EC2 instance reporting files on two devices at once

  - by Philip Isaacs

  I have on EC2 instance with two attached EBS drives. One drive /dev/sda1 is mounted on / The second /dev/sda2 is mounted on /var2 So here's what's strange. Whenever I add any files to /var2 the it is also reporting that the / device is also filling up. As if they are the same device. It's so strange. So if I were to save a 10 mb file to a directory on /var2. Both / and /var2 use 10 mb of space up. Is this bizarre?

  Read the article

• How to send a popup message to unknow computer connected to my WLAN?

  - by Leandro

  Is there any way to send a popup message from a Linux systen to a "random" laptop/tablet/mobile linked to my Wireless network ? For example, if I let my WLAN open and I see a not recognized computer connected to it, is there anyway to send to that device a message ? On the other hand, if I am connected to someone else open network and they may or may not be aware that their network is open, can I send them a message warning that I am accessing their network? Probably for a completely "random" device the answer should be no. But if we restrict to laptops with Win7 or Linux SO is there any service running by default on such systems that allows one to send such popup messages ? PS: I have no practical motivation for this question. This is only a curiosity.

  Read the article

• nc or socat: How to read data from remote:/dev/ttyACM0 ?

  - by AndreasT

  I have a device running at a remote computer on /dev/ttyACM0 Now I want to read that data on my computer. I can connect to it over ssh. Unfortunately I am a nc/socat rookie and no howto covered this. Semantically like this: cat remote:/dev/ttyACM0 The remote system has a limited linux on it, and I can't install packages. (socat is not available there, nc is) Super cool would be to have some forwarded device: local:/dev/ttySOCK0 pointing to remote:/dev/ttyACM0 Thanks for any help.

  Read the article

• MacBook (late 2008) EFI Firmware Update 1.8 Problem

  - by user20832

  Last night I applied EFI Firmware update 1.8 to my Macbook (late 2008). After installing EFI Firmware Update and rebooted my computer and installed SuperDrive Firmware Update 3.0. After that my Macbook rebooted and a black screen is showing with "No bootable device. Please insert bootable device and press any key to continue". I put in one of the bootable installation disck (MAC OS) and it's still stuck on the same screen. I have also tried restarting my macbook manually but no luck. Have anyone experienced that?

  Read the article

• Can SATA be used to connect computers?

  - by André

  Can SATA be used to connect two computers together, just like a crossover Ethernet cable would do ? I know SATA has no "networking" features and even though a controller may have multiple ports, the drives don't "see" each other, and that in SATA one device acts as the host (the computer) and the other device is some kind of "client" (the storage drive). But still, did anyone attempt to make a kernel module that would make one computer appear as a "client" (so that the host's SATA controller detects it as a standard hard drive) and then set up like a pseudo-Ethernet link or a very high speed serial link (and then run pppd on it and do networking) ? Note : I know this is an unprofessional and totally stupid idea, I'm just asking out of curiosity.

  Read the article

• How can I disable the automatic switch to "library" mode in Windows 7's Media Player 12?

  - by matthews

  Whenever I plug any USB device into my computer while running Windows Media Player 12 in Windows 7, it will automatically swtich the player from the Now Playing mode to Library mode. This is intended to faciliate syncing between Media Player and MP3 players, but it happens for any USB device. I'd like this to not happen since it's infuriating to see this take place while I'm watching something on a separate screen in Media Player just from plugging in a USB key. This has nothing to do with Windows autorun, and nothing to do with versions of Windows pre-7. And no, switching to some other video player is not an option; I've tried them all, none are as good as stock Media Player in 7.

  Read the article

• Cisco ASA 5505 and slow download speeds for Apple devices

  - by James

  For traffic routing through my ASA 5505, downloads for all Apple devices, including AppleTV iPad gen 1 IMac MacBook Pro are very slow. speedof.me show less than 1 Mbps download (where I should have 20 Mbps +), yet for any Windows-based device, the download speeds are in excess of 20 Mbps. The Windows device, including the iMac and MacBook Pro machines, are connected via ethernet cable. Why are Apple devices experiencing such pain? Is it an ASA setting, or something else? Thanks.

  Read the article

• The bcdedit export operation fails. windows vista not booting.

  - by ocurro

  I'm fixing my boot record with bootrec.exe, the first command goes: C:\>bcdedit /export c:\BCD_Backup Immediately I receive this error here: The store export operation has failed. The requested system device cannot be found. Likewise, the next command fails, because bcd file is missing: C:\>attrib bcd -s -h -r Lastly, when trying the next command, all it returns is "The requested system device cannot be found". C:\>bootrec /RebuildBcd I'm using Windows 7 setup image to operate. Have Vista installed atm. Has it happened to you? I'd appreciate some orientation.

  Read the article

• How to copy directories using debugfs?

  - by STM

  The debugfs manpage gives the impression that the command 'rdump . .' will recursively copy all files found on the specified filesystem from the debugfs cwd to the native filesystem's cwd. Instead I seem to receive a syntax error, and no copy is initiated? These are the commands I run: cd /path/to/transfer/destination debugfs /dev/sda1 -R rdump . . My task is to copy the entire contents of a clean yet unmountable USB storage device to its host machine's HD. The host machine does not support the inode size used by the USB device's filesystem (256) and its software is not upgradeable, so my intention was to use debugfs to transfer the files. If anyone has any other suggestions for this task I'd be grateful.

  Read the article

• Spoof user agent for GoGo Inflight Internet?

  - by AndyL

  Is it possible to trick the GoGo Inflight WiFi on airlines into thinking that you have a mobile device instead of a laptop? It seems like most airlines that offer in flight wireless these days use GoGo. They offer different pricing for mobile and laptops. It seems like they are checking the browser's user agent. Out of curiosity, is it possible to use a Firefox extension like this one to spoof the user-agent and allow a laptop to access the internet under a GoGo mobile plan? How would GoGo handle something like an IMAP email client, like Thunderbird. Do IMAP clients have a user-agent field as well that would normally identify whether the mail client is running on a laptop or mobile device?

  Read the article

• Flash player, HD videos and games are choppy

  - by Aimad Majdou

  I have a problem with flash player. HD videos from Youtube or Vimeo and flash games do not play smoothly. I'm using Flash player 11, Windows 7 Sp1, and my graphic card is Intel GMA 4500. Device Manager shows me that all drivers are installed on my computer, so i don't have any problems with drivers. When I run Google chrome, Resource Monitor shows me 15% ~ 40 % of CPU Usage and 40% used Physical Memory, but when I watch a video on Youtube or play a Flash game, the Resource Monitor shows 70% - 90% CPU Usage. Also, when I run some HD Video (Frame width : 1920, Frame height : 1080) on my computer, Device Manager shows me 80% ~ 100% of CPU Usage. before I Reinstall Windows 7, HD Videos and flash games were play smoothly I hadn't any problem with them !! I hope all these informations are enough to answer my question.

  Read the article

• Can someone explain the "use-cases" for the default munin graphs?

  - by exhuma

  When installing munin, it activates a default set of plugins (at least on ubuntu). Alternatively, you can simply run munin-node-configure to figure out which plugins are supported on your system. Most of these plugins plot straight-forward data. My question is not to explain the nature of the data (well... maybe for some) but what is it that you look for in these graphs? It is easy to install munin and see fancy graphs. But having the graphs and not being able to "read" them renders them totally useless. I am going to list standard plugins which are enabled by default on my system. So it's going to be a long list. For completeness, I am also going to list plugins which I think to understand and give a short explanation as to what I think it's used for. Pleas correct if I am wrong with any of them. So let me split this questions in three parts: Plugins where I don't even understand the data Plugins where I understand the data but don't know what I should look out for Plugins which I think to understand Plugins where I don't even understand the data These may contain questions that are not necessarily aimed at munin alone. Not understanding the data usually mean a gap in fundamental knowledge on operating systems/hardware.... ;) Feel free to respond with a "giyf" answer. These are plugins where I can only guess what's going on... I hardly want to look at these "guessing"... Disk IOs per device (IOs/second)What's an IO. I know it stands for input/output. But that's as far as it goes. Disk latency per device (Average IO wait)Not a clue what an "IO wait" is... IO Service TimeThis one is a huge mess, and it's near impossible to see something in the graph at all. Plugins where I understand the data but don't know what I should look out for IOStat (blocks/second read/written)I assume, the thing to look out for in here are spikes? Which would mean that the device is in heavy use? Available entropy (bytes)I assume that this is important for random number generation? Why would I graph this? So far the value has always been near constant. VMStat (running/I/O sleep processes)What's the difference between this one and the "processes" graph? Both show running/sleeping processes, whereas the "Processes" graph seems to have more details. Disk throughput per device (bytes/second read/written) What's thedifference between this one and the "IOStat" graph? inode table usageWhat should I look for in this graph? Plugins which I think to understand I'll be guessing some things here... correct me if I am wrong. Disk usage in percent (percent)How much disk space is used/remaining. As this is approaching 100%, you should consider cleaning up or extend the partition. This is extremely important for the root partition. Firewall Throughput (packets/second)The number of packets passing through the firewall. If this is spiking for a longer period of time, it could be a sign of a DOS attack (or we are simply recieving a large file). It can also give you an idea about your firewall performance. If it's levelling out and you need more "power" you should consider load balancing. If it's levelling out and see a correlation with your CPU load, it could also mean that your hardware is not fast enough. Correlations with disk usage could point to excessive LOG targets in you FW config. eth0 errors (packets in/out)Network errors. If this value is increasing, it could be a sign of faulty hardware. eth0 traffic (bits/second in/out)Raw network traffic. This should correlate with Firewall throughput. number of threadsAn ever-increasing value might point to a process not properly closing threads. Investigate! processesBreakdown of active processes (including sleeping). A quick spike in here might point to a fork-bomb. A slowly, but ever-increasing value might point to an application spawning sub-processes but not properly closing them. Investigate using ps faux. process priorityThis shows the distribution of process priorities. Having only high-priority processes is not of much use. Consider de-prioritizing some. cpu usageFairly straight-forward. If this is spiking, you may have an attack going on, or a process is hogging the CPU. Idf it's slowly increasing and approaching max in normal operations, you should consider upgrading your hardware (or load-balancing). file table usageNumber of actively open files. If this is reaching max, you may have a process opening, but not properly releasing files. load averageShows an summarized value for the system load. Should correlate with CPU usage. Increasing values can come from a number of sources. Look for correlations with other graphs. memory usageA graphical representation of you memory. As long as you have a lot of unused+cache+buffers you are fine. swap in/outShows the activity on your swap partition. This should always be 0. If you see activity on this, you should add more memory to your machine!

  Read the article

• Logitech gamepad f710 and ubuntu and as an input to a python program

  - by wherestheforce

  I would like to use the Logitech F710 gamepad as an input device to a python program. I am using Ubuntu. I do not really know where to start, so here are a few questions: How does Ubuntu detect the gamepad? If the gamepad is recognized within Ubuntu, how would I interact with this device via a python script? If this is not easy to do in Ubuntu, how would I interact with the gamepad via a python script in Windows? Thanks!

  Read the article

• renaming hard drives (sdc to sdb) on the fly

  - by w00t

  ata2: link is slow to respond, please be patient (ready=0) kernel: [2761026.198796] ata2: soft resetting link kernel: [2761031.226669] ata2.00: disabled kernel: [2761031.226720] ata2: EH complete kernel: [2761031.226753] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK After receiving the error above, I couldn't access /dev/sdb anymore. Not wanting to restart the server, I rescanned for the device using echo "- - -" > /sys/class/scsi_host/host1/scan and it readded the drive as /dev/sdc. From what I have found, I need to use echo "scsi add-single-device 0 0 3 0" > /proc/scsi/scsi, "3" being the SCSI ID which corresponds to sdb. Everything nice up to the point I execute the command and get -bash: echo: write error: Invalid argument. All the solutions point to using this method, but I am unable to. Any other method available? Debian 5.0.8 - 2.6.26-1-686

  Read the article

• bluetooth doesn't turn off during sleep in Windows 7

  - by lajos

  I have a Bluetooth USB dongle on a Windows 7 laptop. I did not install any Bluetooth drivers, so I assume that the device is using the Microsoft stack. When the computer goes to sleep, the Bluetooth adapter stays on. I don't want Bluetooth devices to wake the computer, so I want sleep to turn off the dongle, but I can't find power management options for Bluetooth in the Control Panel and Device Manager. I also have an issue where the computer doesn't reach full sleep mode, I'm hoping that turning Bluetooth off will solve that problem, too. How can I turn off Bluetooth during sleep?

  Read the article

• Nokia Pc Suite problems with bluetooth (win7)

  - by wurlog

  I have a new Nokia C5-00 and a HP 620. The Bluetoothdriver are installed and the windows Bluetoothstack finds the mobile. After installing Nokia PC Suite I am asked to choose a connection method. As I click on Bluetooth the Nokia PC Suite shows an error message: "Cannot use the connection type.Check that all the needd hardware,software and drivers are available. (Code: OpenMedia)" I tried to switch it on and off via the "wireless" key on the laptop. The HP Software for the button shows that the Bluetooth is deactivated and advices me to go to the device manager and activate the Bluetooth device. Strangely the Bluetooth symbol (I guess from the windows Bluetoothstack) pops up at the same time and I can use the Bluetooth in it's basic windows features, but still nokia suite won't work. ideas????

  Read the article

• sniffing on a switched LAN

  - by shodanex

  Hi, I often find myself in the position of having to sniff on a connection between for example an arm board I am developing on, and another computer on the network, or out of the network. The easy situation is when I can install a sniffer on the computer talking to the embedded device. When it is not possible, I currently install an old 10Mb/s HUB. However I am afraid my HUB might stop working, and I would like to know some alternative. Here are the alternatives I could think of : Buy another HUB. Is that still possible ? Have some sort of ethernet sniffing bridge, like what they do for USB. I am afraid this kind of device is expensive. use ARP poisoning.

  Read the article

• How to add a new entry to fstab?

  - by Roei

  I mount a device mount /dev/xvdf /mnt/mongo and verify the mount using df-h: Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 955M 6.9G 12% / tmpfs 299M 44K 299M 1% /dev/shm /dev/xvdf 20G 589M 19G 4% /mnt/mongo But now I'm trying to figure out how to make it auto mount on boot. I understand I need to add a new entry to /etc/fstab, so I perform: $ sed -i '$ a\/dev/xvdf /mnt/mongo xfs defaults 1 1' /etc/fstab But, after reboot, it seems that the auto mount didn't work. The device didn't appear in the df -h list. Should I not use the sed to add the entry? Is the entry I entered incorrect?

  Read the article

• Asus EeePC X101CH Touchpad issue

  - by ssvarc

  I have an Asus EeePC X101CH that the touchpad was uninstalled from (I saw the uninstall dialog boxes open). After a restart there was a PS/2 mouse under View Hidden Devices in Device Manager that wasn't installed properly (I'm assuming that this is the touchpad). Going to the Asus website and downloading the drivers (V15.3.27.1), I get the error message "Synaptics device not found!". I tried the other driver Version v9.1.7.7 for the Sentelic TouchPad as well (when run it appears to be the driver for the finger sensing) and got the error message "This driver version is inapplicable for the touch pad. Please check the devices on the system and install the suitable driver.". What's my next step? Thanks!

  Read the article

< Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >