Search Results

Search found 8189 results on 328 pages for 'fedora 16'.

Page 150/328 | < Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >

• debian lenny xen bridge networking problem

  - by Sasha

  DomU isn't talking to the world, but it talks to Dom0. Here are the tests that I made: Dom0 (external networking is working): ping 188.40.96.238 #Which is Domu's ip PING 188.40.96.238 (188.40.96.238) 56(84) bytes of data. 64 bytes from 188.40.96.238: icmp_seq=1 ttl=64 time=0.092 ms DomU: ping 188.40.96.215 #Which is Dom0's ip PING 188.40.96.215 (188.40.96.215) 56(84) bytes of data. 64 bytes from 188.40.96.215: icmp_seq=1 ttl=64 time=0.045 ms ping 188.40.96.193 #Which is the gateway - fail PING 188.40.96.193 (188.40.96.193) 56(84) bytes of data. ^C --- 188.40.96.193 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1013ms The system is debian lenny with a normal setup. Here is my configs: uname -a Linux green0 2.6.26-2-xen-686 #1 SMP Wed Aug 19 08:47:57 UTC 2009 i686 GNU/Linux cat /etc/xen/green1.cfg |grep -v '#' kernel = '/boot/vmlinuz-2.6.26-2-xen-686' ramdisk = '/boot/initrd.img-2.6.26-2-xen-686' memory = '2000' root = '/dev/xvda2 ro' disk = [ 'file:/home/xen/domains/green1/swap.img,xvda1,w', 'file:/home/xen/domains/green1/disk.img,xvda2,w', ] name = 'green1' vif = [ 'ip=188.40.96.238,mac=00:16:3E:1F:C4:CC' ] on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' ifconfig eth0 Link encap:Ethernet HWaddr 00:24:21:ef:2f:86 inet addr:188.40.96.215 Bcast:188.40.96.255 Mask:255.255.255.192 inet6 addr: fe80::224:21ff:feef:2f86/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3296 errors:0 dropped:0 overruns:0 frame:0 TX packets:2204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:262717 (256.5 KiB) TX bytes:330465 (322.7 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) peth0 Link encap:Ethernet HWaddr 00:24:21:ef:2f:86 inet6 addr: fe80::224:21ff:feef:2f86/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:3407 errors:0 dropped:657431448 overruns:0 frame:0 TX packets:2291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:319941 (312.4 KiB) TX bytes:338423 (330.4 KiB) Interrupt:16 Base address:0x8000 vif2.0 Link encap:Ethernet HWaddr fe:ff:ff:ff:ff:ff inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:151 errors:0 dropped:33 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1164 (1.1 KiB) TX bytes:20974 (20.4 KiB) ip a s 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: peth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000 link/ether 00:24:21:ef:2f:86 brd ff:ff:ff:ff:ff:ff inet6 fe80::224:21ff:feef:2f86/64 scope link valid_lft forever preferred_lft forever 4: vif0.0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 5: veth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 6: vif0.1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 7: veth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 8: vif0.2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 9: veth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 10: vif0.3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 11: veth3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 12: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 00:24:21:ef:2f:86 brd ff:ff:ff:ff:ff:ff inet 188.40.96.215/26 brd 188.40.96.255 scope global eth0 inet6 fe80::224:21ff:feef:2f86/64 scope link valid_lft forever preferred_lft forever 14: vif2.0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 32 link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff inet6 fe80::fcff:ffff:feff:ffff/64 scope link valid_lft forever preferred_lft forever brctl show bridge name bridge id STP enabled interfaces eth0 8000.002421ef2f86 no peth0 vif2.0 ip r l Dom0: 188.40.96.192/26 dev eth0 proto kernel scope link src 188.40.96.215 default via 188.40.96.193 dev eth0 DomU: 188.40.96.192/26 dev eth0 proto kernel scope link src 188.40.96.238 default via 188.40.96.193 dev eth0

  Read the article

• Linux Kernel Messages: ata1.00: status: { DRDY ERR }

  - by PM

  I am receiving a lot of these messages. Is my HD going to die tomorrow morning? ata1: link is slow to respond, please be patient (ready=0) ata1: device not ready (errno=-16), forcing hardreset ata1: soft resetting link ata1: clearing spurious IRQ ata1: clearing spurious IRQ ata1: clearing spurious IRQ ata1.00: configured for UDMA/33 ata1: EH complete ata1.00: qc timeout (cmd 0xa0) ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata1.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 res 51/20:03:00:00:00/00:00:00:00:00/a0 Emask 0x5 (timeout)

  Read the article

• Route additional network through Sonicwall site-to-site VPN

  - by Brandon

  I have a sonicwall site to site vpn. At one of the sites there is another Cisco vpn to another site. I need to route the traffic for the cisco vpn through the site to site from the other sonicwall site. Site A - 10.10.0.0 /16 network Site B - 192.168.1.0 /24 Sonicwall, A cisco vpn is on 192.168.1.226 address and has routes the 10.10.0.0 network to Site A. Site C - 192.168.2.0 /24 Sonicwall Site A-B VPN is working Site B-C VPN is working I need to get Site C to transmit the 10.10.0.0 traffic over the VPN to site B and then out the Cisco device.

  Read the article

• ClearMyTracksByProcess - all options?

  - by Jonny Blaze

  I've seen the list of values floating around the internet for ClearMyTracksByProcess Delete Temporary Internet Files: RunDll32.exe InetCpl.cpl,ClearMyTracksByProcess 8 Delete Cookies: RunDll32.exe InetCpl.cpl,ClearMyTracksByProcess 2 Delete History: RunDll32.exe InetCpl.cpl,ClearMyTracksByProcess 1 Delete Form Data: RunDll32.exe InetCpl.cpl,ClearMyTracksByProcess 16 Delete Passwords: RunDll32.exe InetCpl.cpl,ClearMyTracksByProcess 32 Delete All: RunDll32.exe InetCpl.cpl,ClearMyTracksByProcess 255 Delete All + files and settings stored by Add-ons: RunDll32.exe InetCpl.cpl,ClearMyTracksByProcess 4351 But it's not a complete list of all the options, and I can't seem to find a complete list (whether there isn't one published, or this one has been republished too many times and is hogging all the search results, I'm not sure). What I'm looking to do is delete Cookies + Temp + Add-ons, but preserve History, Form data, and Passwords. Has anybody found a complete list of all the available options? Or just the option for Add-ons so I can do the math myself? (e.g. Add-ons value + 8 + 2 = the answer I'm looking for) Thanks for looking at my question!

  Read the article

• What are Subnet Mask and Gateway exactly

  - by Saif Bechan

  I have a dedicated server with multiple IP adresses. I run them on Plesk but some of the names are confusing me. One ip has a subnet mask of 225.225.225.192, another has 225.225.225.0. What does this mean and what happens if i change that. Another thing i got a gateway. What is that and when will that come in handy. Another thing I see sometimes behind the ip's is /number. For example: 200.20.20.20/24 200.20.20.20/16 200.20.20.20/8 What will these numbers say.

  Read the article

• Linux IPTables / routing issue

  - by Jon

  Hi all, EDIT 1/3/10 22:00 GMT - rewrote some of it after further investigation It has been a while since I looked at IPtables and I seem to be worse than before as I can not seem to get my webserver online. Below is my firewall rules on the gateway server that is running the dhcp server accessing the net. The webserver is inside my network on a static IP (192.168.0.98, default port). When I use Nmap or GRC.com I see that port 80 is open on the gateway server but when I browse to it, (via public URL. http://www.houseofhawkins.com) it always fails with a connection error, (nmap cannot connect and figure out what the web server is either). I can nmap the webserver and browse to it just fine via same IP inside my network. I believe it is my IPTable rules that are not letting it through. Internally I can route all my requests. Each machine can browse to the website and traffic works just fine. I can MSTSC / ssh to all the webservers internally and they inturn can connect to the web. IPTABLE: *EDIT - Added new firewall rules 2/3/10 * #!/bin/sh iptables="/sbin/iptables" modprobe="/sbin/modprobe" depmod="/sbin/depmod" EXTIF="eth2" INTIF="eth1" load () { $depmod -a $modprobe ip_tables $modprobe ip_conntrack $modprobe ip_conntrack_ftp $modprobe ip_conntrack_irc $modprobe iptable_nat $modprobe ip_nat_ftp echo "enable forwarding.." echo "1" > /proc/sys/net/ipv4/ip_forward echo "enable dynamic addr" echo "1" > /proc/sys/net/ipv4/ip_dynaddr # start firewall # default policies $iptables -P INPUT DROP $iptables -F INPUT $iptables -P OUTPUT DROP $iptables -F OUTPUT $iptables -P FORWARD DROP $iptables -F FORWARD $iptables -t nat -F #echo " Opening loopback interface for socket based services." $iptables -A INPUT -i lo -j ACCEPT $iptables -A OUTPUT -o lo -j ACCEPT #echo " Allow all connections OUT and only existing and related ones IN" $iptables -A INPUT -i $INTIF -j ACCEPT $iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A OUTPUT -o $EXTIF -j ACCEPT $iptables -A OUTPUT -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A FORWARD -i $EXTIF -o $INTIF -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A FORWARD -i $INTIF -o $EXTIF -j ACCEPT $iptables -A FORWARD -j LOG --log-level 7 --log-prefix "Dropped by firewall: " $iptables -A INPUT -j LOG --log-level 7 --log-prefix "Dropped by firewall: " $iptables -A OUTPUT -j LOG --log-level 7 --log-prefix "Dropped by firewall: " #echo " Enabling SNAT (MASQUERADE) functionality on $EXTIF" $iptables -t nat -A POSTROUTING -o $EXTIF -j MASQUERADE $iptables -A INPUT -i $INTIF -j ACCEPT $iptables -A OUTPUT -o $INTIF -j ACCEPT #echo " Allowing packets with ICMP data (i.e. ping)." $iptables -A INPUT -p icmp -j ACCEPT $iptables -A OUTPUT -p icmp -j ACCEPT $iptables -A INPUT -p udp -i $INTIF --dport 67 -m state --state NEW -j ACCEPT #echo " Port 137 is for NetBIOS." $iptables -A INPUT -i $INTIF -p udp --dport 137 -j ACCEPT $iptables -A OUTPUT -o $INTIF -p udp --dport 137 -j ACCEPT #echo " Opening port 53 for DNS queries." $iptables -A INPUT -p udp -i $EXTIF --sport 53 -j ACCEPT #echo " opening Apache webserver" $iptables -A PREROUTING -t nat -i $EXTIF -p tcp --dport 80 -j DNAT --to 192.168.0.96:80 $iptables -A FORWARD -p tcp -m state --state NEW -d 192.168.0.96 --dport 80 -j ACCEPT } flush () { echo "flushing rules..." $iptables -P FORWARD ACCEPT $iptables -F INPUT $iptables -P INPUT ACCEPT echo "rules flushed" } case "$1" in start|restart) flush load ;; stop) flush ;; *) echo "usage: start|stop|restart." ;; esac exit 0 route info: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 5e0412a6.bb.sky * 255.255.255.255 UH 0 0 0 eth2 192.168.0.0 * 255.255.255.0 U 0 0 0 eth1 default 5e0412a6.bb.sky 0.0.0.0 UG 100 0 0 eth2 ifconfig: eth1 Link encap:Ethernet HWaddr 00:22:b0:cf:4a:1c inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::222:b0ff:fecf:4a1c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:79023 errors:0 dropped:0 overruns:0 frame:0 TX packets:57786 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11580918 (11.5 MB) TX bytes:22872030 (22.8 MB) Interrupt:17 Base address:0x2b00 eth2 Link encap:Ethernet HWaddr 00:0c:f1:7c:45:5b inet addr:94.4.18.166 Bcast:94.4.18.166 Mask:255.255.255.255 inet6 addr: fe80::20c:f1ff:fe7c:455b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:57038 errors:0 dropped:0 overruns:0 frame:0 TX packets:34532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:21631721 (21.6 MB) TX bytes:7685444 (7.6 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1517 (1.5 KB) TX bytes:1517 (1.5 KB) EDIT OK so as requested I will try and expand on my infrastructure: I previously had it setup with a Sky broadband modem router that did the DHCP and I used its web interface to port forward the web across to the web server. The network looked something like this: I have now replaced the sky modem with a dlink modem which gives the IP to the gateway server that now does the DHCP. It looks like: The internet connection is a standard broadband connection with a dynamic IP, (use zoneedit.com to keep it updated). I have tried it on each of the webservers(one Ubuntu Apache server and one WS2008 IIS7). I think there must also be an issue with my IPTable rules as it can route to my win7 box which has the default IIS7 page and that would not display when I forwarded all port 80 to it. I would be really grateful for any and all help with this. Thanks Jon

  Read the article

• Ubuntu 9.10 Samba NT_STATUS_CONNECTION_REFUSED errors on remote machines.

  - by user40730

  SAMBA I'm running Samba on Ubuntu 9.10 on a MacBook Pro using Parallels. When I run the smbtree command, I get the following errors: peterv@MBP17U<2005$: sudo smbtree Enter root's password: session request to 192.168.1.156 failed (Called name not present) HADEN \SERVER2 cli_start_connection: failed to connect to SERVER2<20 (0.0.0.0). Error NT_STATUS_CONNECTION_REFUSED \MBP17WIN MBP17win cli_start_connection: failed to connect to MBP17WIN<20 (0.0.0.0). Error NT_STATUS_CONNECTION_REFUSED \MBP17U \MBP17U\IPC$ IPC Service () \MBP17U\Perl \MBP17U\Home \MBP17U\print$ \MBP17 MBP17 cli_start_connection: failed to connect to MBP17<20 (0.0.0.0). Error NT_STATUS_CONNECTION_REFUSED Fri Apr 16 05:24:47 EDT 2010 The MBP17 failure is an OS X system, the SERVER2 failure is a Windows XP system. Running testparm shows no errors. Can someone please help me out?

  Read the article

• How to move linux executables to a ramdisk?

  - by alfa64

  i've made a ramdisk this way: mkdir -p /media/ramdisk mount -t tmpfs -o size=512M tmpfs /media/ramdisk/ The reason for this is because i run a lot of node.js scripts and their execution time is very small, but i suspect that the time overhead is because it reloads the node.js executable from disk and destroys it on each subsecuent run. So i think this might be the solution to gain a bit, if not much, performance. How can i move a program like node to the ramdisk and run it from there? The idea is to have a startup script that creates the ramdisk and puts the node files inside of it. Note that i'm currently using fedora 16 for what's it's worth. Thanks in advance.

  Read the article

• Multiple vlan issue with procurve switch

  - by Chris-AZ

  I have a cisco asa5505 as my rtr/fw(10.1.3.254). I have vlan 1 and vlan 3. Vlan 1 is my default all access vlan. Vlan 3 is my Guest(dmz) vlan. I can't seem to get a dhcp ip address when my laptop is plugged into port 42 on my procurve. I have plugged my laptop directly into the firewall and it gets a dhcp ip fine(the firewall is dhcp server). the firewall is plugged into port 41. Only vlan3 needs to go over port 41. I'm sure I have a bonehead config problem however I'm about ready to pull out what little hair I have left. vlan 1 name "Computers" forbid 45 untagged 1-41,43-44 ip helper-address 10.1.1.16 ip address 10.1.1.1 255.255.255.0 tagged 46-48 no untagged 42,45 exit vlan 3 name "Guest Wireless" ip helper-address 10.1.3.254 ip address 10.1.3.1 255.255.255.0 tagged 41-42,44-48 exit

  Read the article

• Problem with testsaslauthd and kerberos5 ("saslauthd internal error")

  - by danorton

  The error message “saslauthd internal error” seems like a catch-all for saslauthd, so I’m not sure if it’s a red herring, but here’s the brief description of my problem: This Kerberos command works fine: $ echo getprivs | kadmin -p username -w password Authenticating as principal username with password. kadmin: getprivs current privileges: GET ADD MODIFY DELETE But this SASL test command fails: $ testsaslauthd -u username -p password 0: NO "authentication failed" saslauthd works fine with "-a sasldb", but the above is with "-a kerberos5" This is the most detail I seem to be able to get from saslauthd: saslauthd[]: auth_krb5: krb5_get_init_creds_password: -1765328353 saslauthd[]: do_auth : auth failure: [user=username] [service=imap] [realm=] [mech=kerberos5] [reason=saslauthd internal error] Kerberos seems happy: krb5kdc[](info): AS_REQ (4 etypes {18 17 16 23}) 127.0.0.1: ISSUE: authtime 1298779891, etypes {rep=18 tkt=18 ses=18}, username at REALM for krbtgt/DOMAIN at REALM I’m running Ubuntu 10.04 (lucid) with the latest updates, namely: Kerberos 5 release 1.8.1 saslauthd 2.1.23 Thanks for any clues.

  Read the article

• Script for run script on vbs

  - by user31568

  Hello everybody I have a script on vbscript Dim WSHShell, WinDir, Value, wshProcEnv, fso, Spath Set WSHShell = CreateObject("WScript.Shell") Dim objFSO, objFileCopy Dim strFilePath, strDestination Const OverwriteExisting = True Set objFSO = CreateObject("Scripting.FileSystemObject") Set windir = objFSO.getspecialfolder(0) objFSO.CopyFile "\dv.rt.ru\SYSVOL\DV.RT.RU\scripts\shutdown.vbs", windir&"\", OverwriteExisting strComputer = "." Set objWMIService = GetObject("winmgmts:" _ & "{impersonationLevel=impersonate}!\" _ & strComputer & "\root\cimv2") JobID = "1" Set colScheduledJobs = objWMIService.ExecQuery _ ("Select * from Win32_ScheduledJob") For Each objJob in colScheduledJobs objJob.Delete Next Set objNewJob = objWMIService.Get("Win32_ScheduledJob") errJobCreate = objNewJob.Create _ (windir & "\shutdown.vbs", "**093000.000000+660", _ True, 1 OR 2 OR 4 OR 8 OR 16 OR 32 OR 64, ,True, JobId) How make that shutdown.vbs not run once at 9:30 but run for 9:30 to 12:00

  Read the article

• Script for run script on vbs

  - by user35729

  Hello everybody I have a script on vbscript Dim WSHShell, WinDir, Value, wshProcEnv, fso, Spath Set WSHShell = CreateObject("WScript.Shell") Dim objFSO, objFileCopy Dim strFilePath, strDestination Const OverwriteExisting = True Set objFSO = CreateObject("Scripting.FileSystemObject") Set windir = objFSO.getspecialfolder(0) objFSO.CopyFile "\dv.rt.ru\SYSVOL\DV.RT.RU\scripts\shutdown.vbs", windir&"\", OverwriteExisting strComputer = "." Set objWMIService = GetObject("winmgmts:" _ & "{impersonationLevel=impersonate}!\" _ & strComputer & "\root\cimv2") JobID = "1" Set colScheduledJobs = objWMIService.ExecQuery _ ("Select * from Win32_ScheduledJob") For Each objJob in colScheduledJobs objJob.Delete Next Set objNewJob = objWMIService.Get("Win32_ScheduledJob") errJobCreate = objNewJob.Create _ (windir & "\shutdown.vbs", "**093000.000000+660", _ True, 1 OR 2 OR 4 OR 8 OR 16 OR 32 OR 64, ,True, JobId) How make that shutdown.vbs not run once at 9:30 but run for 9:30 to 12:00

  Read the article

• HP Pavilion dv6000 graphics issue

  - by Tony

  A few days ago my laptop seized up on me while I was playing a game. When I restarted the computer, it sent me back to 640x480 resolution with 16 colors (clearly a graphical issue). In device manager, it shows an error, stating "Windows has stopped this device because it has reported problems. (Code 43)" regarding the video card. Upon removing and re-installing the drivers using both Windows Update and my own searching through nvidia's site, it's given me zero results. For kicks, I ran my antivirus (you never know!) and registry cleaner to see if anything would turn up. The antivirus found nothing, but CCleaner found 27 registry errors all dealing with my video card. What could be the cause of this, and what course of action would you recommend in this situation? Thanks in advance for the help! OS: Windows 7 Professional GPU: nvidia GeForce 8400M GS

  Read the article

• Problem with Apache webserver and MySQL after installing cPanel

  - by Santhosh S

  I have a Fedora machine with Apache webserver and MySQL installed with some data present in both the servers. I installed cPanel on this machine with a test license. After installing cPanel I am not able to start Apache Webserver and login to MySQL. I am getting the following error when I try to start the webserver Building global cache for cpanel...warn [Cpanel::AdvConfig::apache::modules] Unable to locate executable Apache binary warn [Cpanel::AdvConfig::apache::modules] Unable to locate executable Apache binary

  Read the article

• 10/100 Network performing at 1.5 to 2.0 megabyte per second - is that below normal?

  - by burnt1ce

  This comes out to about 12 to 16 megabit/seond. I've read in forums that people are getting much higher speeds (ie: "40-60 Mb/s" http://forums.cnet.com/5208-7589_102-0.html?threadID=265967). I'm getting my benchmark by having a unmanged 5 port switch connected to a WRT54GS router connect. I'm sending a file from a computer connect to the WRT54GS to another computer that's connect to the unmanaged 5 port switch. Is the linkage of the switch causing this massive overhead? i doubt it. What could explain the slow down? electrical interference?

  Read the article

• My computer freezes irregularly

  - by Manhim

  My computer started to freeze at irregular times for 3 weeks now. Please note that this question change with each things that i try. (For additional details) What happens My computer freezes, the video stops. (No graphic glitches, it just stops) Sound keeps playing up to some time (Usually 10-30 seconds) then stops playing. Sometimes, randomly, the screen on my G-15 keyboard flickers and I see caracters not at the right places. Usually happens for about 1-2 seconds and a bit before my computer freezes. I have to keep the power button pressed for 4 seconds to shut my computer down. I still hear my hard drives and fans working. Sometimes it works with no problems for a full day, some other times it just keeps freezing each time I restart my computer and I have to leave it for the rest of the day. Sometimes my mouse freezes for a fraction of a second (Like 0.01 to 0.2 seconds) quite randomly, usually before it freezes. No errors spotted by the "Action center" unlike when I had problems with my last video card on this system (Driver errors). My G-15 LCD screen also freezes. Sometimes my G-15 LCD screen flickers and caracters gets caried around temporary under heavy load. Now, most of the times, the BIOS hard disks boot order gets reversed for some reason and I have to put it to the right one and save each times I boot. (Might be unrelated, not sure, but it first started yesterday) Sometimes the BIOS doesn't detect my 750GB hard drive plugged in SATA1. What I did so far I have had similar problems in the past and I had changed my hard drive (It was faulty), so I tested my software RAID-0 array and it was faulty so I changed it. (I reinstalled Windows 7 with this part). I also tested with unplugging my secondary hard drive. My CPU was running at about 100 degree Celsius, I removed the dust between the fans and the heatsink and it's now between 45-55. I ran a CPU stress-test and it didn't freeze during the tests (using Prime95 on all cores) Ran a memory test (using memtest86+) for a single pass and there were no errors. Ran a GPU stress test with ati-tools and furmark and it didn't freeze during the tests. (No artefacts either) I had troubles with my graphic card when I got it, but I think that it got fixed with a driver update. I checked the voltages in my BIOS setup and they all seemed ok (±0.2 I think). I have ran on the computer without problems with Fedora 15 on an external hard drive (Appart that it couldn't load Gnome 3 and was reverting to Gnome 2, didn't want to install drivers since I use it on multiple computers) I used it to backup my files from the raid array to my 1TB hard drive for the reinstallation of Windows. (So the crashes only happenned on Windows) [The external hard drive is plugged directly on a SATA port] I contacted EVGA (My graphic card vendor) and pointed them on this question, I'm looking for an answer. Ran sensors on Fedora 15 and got this output: http://pastebin.com/0BHJnAvu Ran 6 short different CPU stress test on Fedora 15 (Haven't found any complete stress testers for Linux) and it didn't crash. Changed the thermal paste to some Artic Silver 5 for my CPU and stress tested the CPU, temperature was at 50 idle, then 64 highest and slowly went down to 62 during the test. Ran some stress testing with a temporary graphic card and it went ok. Ran furmark stress test with my original graphic card and it freezed again. GPU had a temp of 74C, a CPU temp of 58C and a mobo temp of 40C or 45C (Dunno which one it is from SpeedFan). Ran a furmark stress test and a CPU stress test at the same time, results: http://pastebin.com/2t6PLpdJ I have been using my computer without stressing it for about 2 hours now and no crashes yet. I also have disabled the AMD Cool'n'quiet function on the BIOS for a more regular power to the CPU. When I ran Furmark without C'n'q my computer didn't freeze but I had a "Driver Kernel Error" that have recovered (And Furmark crashed) all that while running a CPU stress test. The computer eventually frozed without me being at it, but this time my screen just went on sleep and I couldn't wake it. Using the stability tester in nTune my computer freezed again (In the same manner as before). I notived that Speedfan gives me a -12V of -16.97V and a -5V of -8.78V. I wonder if these numbers are reliable and if they are good or bad. I have swapped my G-15 with another basic USB keyboard (HP) and I have ran furmark for about 10 minutes with a CPU stability test running each 60 seconds for 30 seconds and my computer haven't crashed yet. Ran some more extended tests without my G-15 and it freezed like it usually do. Removed the nForce Hard disk controler. Disabled command queuing in the NVIDIA nForce SATA Controller for both port 0 and port 1 (Errors from the logs) Used CPUID HwMonitor, here are the voltages: http://pastebin.com/dfM7p4jV Changed some configurations in the motherboard BIOS: Disabled PEG Link Mode, Changed AI Tuning to Standard, Disabled the 1394 Controller, Disabled HD Audio, Disabled JMicron RAID controller and Disabled SATA Raid. When it happens When I play video games (Mostly) When I play flash games (Second most) When I'm looking at my desktop background (It rarely happens when I have a window open, but it does, sometimes) When my Graphic card and my CPU are stressed. Sometimes when my Graphic card is stressed. Never happenned while stressing only the CPU. Sometimes when my CPU is stressed. Specs Windows Seven x64 Home Premium Motherboard: M2N-SLI Deluxe CPU: AMD Phenom 9950 x2 @ 2.6GHz Memory: Kingston 4x2GB Dual Channel (Pretty basic memory sticks) Hard drives: Was 2x250GB (Western digital caviar) in raid-0 + 1TB (WD caviar black), I replaced the raid array with a 750GB (WD caviar black) [Yes I removed the array from the raid configurations] 750W Power supply No overcloking. Ever. There have been some power-downs like 4-5 weeks ago, but the problem didn't start immediately after. (I wasn't home, so my computer got shut-down) Event logs (Warnings, errors and critical errors) for the last 24 hours: http://pastebin.com/Bvvk31T7 My current to-try list Reinstall the drivers and software 1 by 1 and do extensive stress testing between each. Update the BIOS firmware to the most recent stable one. Change my motherboard. Status updates Keeping only the last 3 (28/06 04pm) More stress testing and still pass the tests. (28/06 03pm) Been stress testing for 10 minute straight now and 5 minutes with both CPU and GPU being stressed at the same time. (28/06 03pm) Stress-testing right now, so far no problems. A little hope Tests with Furmark and Prime95. Testing Windows bare-bone: 30 Minutes stress, no freeze. Installing an Anti-virus and some software, restarting computer. Testing with Anti-virus and some software (No drivers installed): 30 Minutes stress, no freeze. Installing audio drivers, restarting computer. Testing with the audio drivers: 30 Minutes stress, no freeze. Installing the latest graphic drivers from EVGA's website (without 3d vision since I don't use it), restarting computer. Testing with the graphic drivers: 30 Minutes stress, no freeze. Configuring Windows to my liking and installing more softwares. In this situation, how can I successfully pin-point the current hardware problem? (If it's a hardware problem) Because I don't really have the budget to just forget and replace everything. I also don't really have hardware to test-replace current hardware.

  Read the article

• Suggest me a good php-fpm configuartion

  - by Werulz

  I am configuring a server for a friend.The server has the following specs 8GB RAM Quad Core processor 1 TB HDD 100 mbps port However all php files are loadking very slowly.I did a speedtest and server takes 16 secs to Load FIRST byte.I strongly believe its my php-fpm configuration.Server uses nginx and php only , no mysql etc... My current php-fpm configuration pm.max_children = 50 pm.start_servers = 10 pm.min_spare_servers = 5 pm.max_spare_servers = 35 Server load and ram usage are perfectly fine Please suggest me a good configuration for this server UPDATE: This configuration works fine pm.max_children = 20 pm.start_servers = 7 pm.min_spare_servers = 5 pm.max_spare_servers = 10 pm.max_requests = 100 The problem with first byte load time is solved.However after like 15-20 hours First byte load time increase gradually. I have to reload php-fpm to get small load time Based on my conf above what i modify to it so that first byte load time remain small and i don't have to restart it:P

  Read the article

• Linux, some packets are not being NAT

  - by user70932

  Hi, I'm trying to NAT HTTP traffic, I'm new to this and facing some issues. What i'm trying to do is NAT client HTTP requests to a webserver. CLIENT - NAT BOX - WEBSERVER When the client open the IP of the NAT BOX, the request should be pass to the web server. But I'm getting "HTTP request sent, awaiting response..." and then wait serveral minutes before the request is done. Looking at the tcpdump output, it looks like the first Syn packet on (10:48:54) is being NAT but not the second, third, fourth... ACK or PSH packets, and wait until (10:52:04) it starts NAT again on the ACK packet. The iptables command I'm using is: iptables -t nat -A PREROUTING -p tcp -i eth0 --dport 80 \ -j DNAT --to-destination WEBSERVER I'm wondering what could have caused this behavior? Thanks alot. 10:48:54.907861 IP (tos 0x0, ttl 49, id 16395, offset 0, flags [DF], proto: TCP (6), length: 48) CLIENT.61736 > NATBOX.http: S, cksum 0x6019 (correct), 1589600740:1589600740(0) win 5840 <mss 1460,nop,wscale 8> 10:48:54.907874 IP (tos 0x0, ttl 48, id 16395, offset 0, flags [DF], proto: TCP (6), length: 48) CLIENT.61736 > WEBSERVER.http: S, cksum 0xb5d7 (correct), 1589600740:1589600740(0) win 5840 <mss 1460,nop,wscale 8> 10:48:55.102696 IP (tos 0x0, ttl 49, id 16397, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > NATBOX.http: ., cksum 0x2727 (correct), ack 2950613896 win 23 10:48:55.102963 IP (tos 0x0, ttl 49, id 16399, offset 0, flags [DF], proto: TCP (6), length: 160) CLIENT.61736 > NATBOX.http: P 0:120(120) ack 1 win 23 10:48:58.103078 IP (tos 0x0, ttl 49, id 16401, offset 0, flags [DF], proto: TCP (6), length: 160) CLIENT.61736 > NATBOX.http: P 0:120(120) ack 1 win 23 10:48:58.366344 IP (tos 0x0, ttl 49, id 16403, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > NATBOX.http: ., cksum 0x26af (correct), ack 1 win 23 10:49:04.103204 IP (tos 0x0, ttl 49, id 16405, offset 0, flags [DF], proto: TCP (6), length: 160) CLIENT.61736 > NATBOX.http: P 0:120(120) ack 1 win 23 10:49:04.363943 IP (tos 0x0, ttl 49, id 16407, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > NATBOX.http: ., cksum 0x26af (correct), ack 1 win 23 10:49:16.101583 IP (tos 0x0, ttl 49, id 16409, offset 0, flags [DF], proto: TCP (6), length: 160) CLIENT.61736 > NATBOX.http: P 0:120(120) ack 1 win 23 10:49:16.363475 IP (tos 0x0, ttl 49, id 16411, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > NATBOX.http: ., cksum 0x26af (correct), ack 1 win 23 10:49:40.100796 IP (tos 0x0, ttl 49, id 16413, offset 0, flags [DF], proto: TCP (6), length: 160) CLIENT.61736 > NATBOX.http: P 0:120(120) ack 1 win 23 10:49:40.563898 IP (tos 0x0, ttl 49, id 16415, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > NATBOX.http: ., cksum 0x26af (correct), ack 1 win 23 10:50:28.099396 IP (tos 0x0, ttl 49, id 16417, offset 0, flags [DF], proto: TCP (6), length: 160) CLIENT.61736 > NATBOX.http: P 0:120(120) ack 1 win 23 10:50:28.761678 IP (tos 0x0, ttl 49, id 16419, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > NATBOX.http: ., cksum 0x26af (correct), ack 1 win 23 10:52:04.093668 IP (tos 0x0, ttl 49, id 16421, offset 0, flags [DF], proto: TCP (6), length: 160) CLIENT.61736 > NATBOX.http: P 0:120(120) ack 1 win 23 10:52:04.093678 IP (tos 0x0, ttl 48, id 16421, offset 0, flags [DF], proto: TCP (6), length: 160) CLIENT.61736 > WEBSERVER.http: P 1589600741:1589600861(120) ack 2950613896 win 23 10:52:04.291021 IP (tos 0x0, ttl 49, id 16423, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > NATBOX.http: ., cksum 0x25d3 (correct), ack 217 win 27 10:52:04.291028 IP (tos 0x0, ttl 48, id 16423, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > WEBSERVER.http: ., cksum 0x7b91 (correct), ack 217 win 27 10:52:04.300708 IP (tos 0x0, ttl 49, id 16425, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > NATBOX.http: ., cksum 0x253c (correct), ack 368 win 27 10:52:04.300714 IP (tos 0x0, ttl 48, id 16425, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > WEBSERVER.http: ., cksum 0x7afa (correct), ack 368 win 27 10:52:04.301417 IP (tos 0x0, ttl 49, id 16427, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > NATBOX.http: F, cksum 0x253b (correct), 120:120(0) ack 368 win 27 10:52:04.301438 IP (tos 0x0, ttl 48, id 16427, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > WEBSERVER.http: F, cksum 0x7af9 (correct), 120:120(0) ack 368 win 27 10:52:04.498875 IP (tos 0x0, ttl 49, id 16429, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > NATBOX.http: ., cksum 0x253a (correct), ack 369 win 27 10:52:04.498881 IP (tos 0x0, ttl 48, id 16429, offset 0, flags [DF], proto: TCP (6), length: 40) CLIENT.61736 > WEBSERVER.http: ., cksum 0x7af8 (correct), ack 369 win 27

  Read the article

• Event Tracing for Windows GUI

  - by Ian Boyd

  i want to view tracing events from the Event Tracing for Windows system. As far as i can tell the only client program that exists for connecting to providers is a command line tool that comes with the Microsoft Windows Device Driver Development Kit (DDK), e.g.: tracelog -start "NT Kernel Logger" -f krnl.etl -dpcisr -nodisk -nonet -b 1024 -min 4 -max 16 -ft 10 –UsePerfCounter ... tracelog –stop It then requires a separate command line tool to convert the generated log file into something usable, e.g.: trcerpt krnl.etl -report isrdpc.xml Has nobody come up with a Windows program (ala Performance Monitor, Process Monitor, Event Viewer) that lets me start tracing by pushing a "Go" button, let me see events, and i can stop it with a "Stop" button? Is there GUI for Event Tracing for Windows?

  Read the article

• Apache 2.4.3 php-fpm mod_fast_cgi and mod_cache

  - by Anjia

  Did anybody successfully configured mod_cache in apache 2.4 with php-fpm and fastcgi? my cgi config: <IfModule mod_fastcgi.c> Alias /php5.fastcgi /var/www/fastcgi/php5.fastcgi AddHandler php-script .php FastCGIExternalServer /var/www/fastcgi/php5.fastcgi -socket /mnt/tmp/fast/php-fpm.sock -idle-timeout 1600 -pass-header Authorization Action php-script /php5.fastcgi virtual My php-fpm config is standard and I am loading mod_cache and mod_disk_cache in Apache. However the Apache does not seems to cache any content. The debug log file: Fri Sep 07 23:22:59.691333 2012] [cache:debug] [pid 35623:tid 123613201929984] mod_cache.c(161): [client 10.0.0.22:21938] AH00750: Adding CACHE_SAVE filter for /index.html [Fri Sep 07 23:22:59.691345 2012] [cache:debug] [pid 35623:tid 123613201929984] mod_cache.c(171): [client 10.0.0.22:21938] AH00751: Adding CACHE_REMOVE_URL filter for /index.html [Fri Sep 07 23:23:01.326598 2012] [cache:debug] [pid 35623:tid 123613185144576] cache_storage.c(626): [client 10.0.0.110:5414] AH00698: cache: Key for entity /index.html?(null) is `http://10.0.1.16:8080/index.html?`

  Read the article

• sudo apt-get moo and other easter eggs in Linux

  - by Arkapravo

  I came across this command while dabbling in Ubuntu 9.10: sudo get-apt moo acer@acer:~$ sudo apt-get moo (__) (oo) /------\/ / | || * /\---/\ ~~ ~~ ...."Have you mooed today?"... Which most surprisingly "made a MOO". (How unfortunate for the cows). Does anyone else know of funny command line easter eggs in their flavour of Linux (Fedora, Slackwire, Mandriva, Solaris, Suse, etc)?

  Read the article

• Logging network activity of LAMP server using BASH

  - by Yarin

  I've got a Fedora LAMP server on Amazon EC2 functioning as a HTTP pseudo-proxy (Sorry, don't know the terminology- It's not a true proxy where requests are relayed through apache, rather client requests are being translated by a PHP script, which then sends a new request.) I'd like to be able to fully log the HTTP cycle CLIENT - PROXY PROXY - SERVICE SERVICE - PROXY PROXY - CLIENT I'm hoping to do this using BASH tools- thinking netcat? Looking for advice and examples. Thanks!

  Read the article

• What is causing the unusual high load average and IOwait?

  - by James

  I noticed on Tuesday night of last week, the load average went up sharply and it seemed abnormal since the traffic is small. Usually, the numbers usually average around .40 or lower and my server stuff (mysql, php and apache) are optimized. I noticed that the IOWait is unusually high even though the processes is barely using any CPU. top - 01:44:39 up 1 day, 21:13, 1 user, load average: 1.41, 1.09, 0.86 Tasks: 60 total, 1 running, 59 sleeping, 0 stopped, 0 zombie Cpu0 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 0.0%us, 0.3%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu4 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu5 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu6 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu7 : 0.0%us, 0.0%sy, 0.0%ni, 91.5%id, 8.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1048576k total, 331944k used, 716632k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 2468 1376 1140 S 0 0.1 0:00.92 init 1656 root 15 0 13652 5212 664 S 0 0.5 0:00.00 apache2 9323 root 18 0 13652 5212 664 S 0 0.5 0:00.00 apache2 10079 root 18 0 3972 1248 972 S 0 0.1 0:00.00 su 10080 root 15 0 4612 1956 1448 S 0 0.2 0:00.01 bash 11298 root 15 0 13652 5212 664 S 0 0.5 0:00.00 apache2 11778 chikorit 15 0 2344 1092 884 S 0 0.1 0:00.05 top 15384 root 18 0 17544 13m 1568 S 0 1.3 0:02.28 miniserv.pl 15585 root 15 0 8280 2736 2168 S 0 0.3 0:00.02 sshd 15608 chikorit 15 0 8280 1436 860 S 0 0.1 0:00.02 sshd Here is the VMStat procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 1 0 0 768644 0 0 0 0 14 23 0 10 1 0 99 0 IOStat - Nothing unusal Total DISK READ: 67.13 K/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 19496 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19501 be/4 mysql 3.95 K/s 0.00 B/s 0.00 % 0.00 % mysqld 19568 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19569 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19570 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19571 be/4 chikorit 7.90 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19573 be/4 chikorit 7.90 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 1 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % init 11778 be/4 chikorit 0.00 B/s 0.00 B/s 0.00 % 0.00 % top 19470 be/4 mysql 0.00 B/s 0.00 B/s 0.00 % 0.00 % mysqld Load Average Chart - http://i.stack.imgur.com/kYsD0.png I want to be sure if this is not a MySQL problem before making sure. Also, this is a Ubuntu 10.04 LTS Server on OpenVZ. Edit: This will probably give a good picture on the IO Wait top - 22:12:22 up 17:41, 1 user, load average: 1.10, 1.09, 0.93 Tasks: 33 total, 1 running, 32 sleeping, 0 stopped, 0 zombie Cpu(s): 0.6%us, 0.2%sy, 0.0%ni, 89.0%id, 10.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1048576k total, 260708k used, 787868k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 2468 1376 1140 S 0 0.1 0:00.88 init 5849 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 8063 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 9732 root 16 0 8280 2728 2168 S 0 0.3 0:00.02 sshd 9746 chikorit 18 0 8412 1444 864 S 0 0.1 0:01.10 sshd 9747 chikorit 18 0 4576 1960 1488 S 0 0.2 0:00.24 bash 13706 chikorit 15 0 2344 1088 884 R 0 0.1 0:00.03 top 15745 chikorit 15 0 12968 5108 1280 S 0 0.5 0:00.00 apache2 15751 chikorit 15 0 72184 25m 18m S 0 2.5 0:00.37 php5-fpm 15790 chikorit 18 0 12472 4640 1192 S 0 0.4 0:00.00 apache2 15797 chikorit 15 0 72888 23m 16m S 0 2.3 0:00.06 php5-fpm 16038 root 15 0 67772 2848 592 D 0 0.3 0:00.00 php5-fpm 16309 syslog 18 0 24084 1316 992 S 0 0.1 0:00.07 rsyslogd 16316 root 15 0 5472 908 500 S 0 0.1 0:00.00 sshd 16326 root 15 0 2304 908 712 S 0 0.1 0:00.02 cron 17464 root 15 0 10252 7560 856 D 0 0.7 0:01.88 psad 17466 root 18 0 1684 276 208 S 0 0.0 0:00.31 psadwatchd 17559 root 18 0 11444 2020 732 S 0 0.2 0:00.47 sendmail-mta 17688 root 15 0 10252 5388 1136 S 0 0.5 0:03.81 python 17752 teamspea 19 0 44648 7308 4676 S 0 0.7 1:09.70 ts3server_linux 18098 root 15 0 12336 6380 3032 S 0 0.6 0:00.47 apache2 18099 chikorit 18 0 10368 2536 464 S 0 0.2 0:00.00 apache2 18120 ntp 15 0 4336 1316 984 S 0 0.1 0:00.87 ntpd 18379 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 18387 mysql 15 0 62796 36m 5864 S 0 3.6 1:43.26 mysqld 19584 root 15 0 12336 4028 668 S 0 0.4 0:00.02 apache2 22498 root 16 0 12336 4028 668 S 0 0.4 0:00.00 apache2 24260 root 15 0 67772 3612 1356 S 0 0.3 0:00.22 php5-fpm 27712 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 27730 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 30343 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 30366 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2

  Read the article

• Seeking glass lcd montiors with LED backlight

  - by dlamblin

  The only LCD monitors with glass fronts and LED back-lighting I can find are the ones by Apple. And they only sell a 24" one at 2.4x the price of any other 24" monitor at 1920x1200, and a 30" one, which honestly I can't put on my desk. Oh, and the 24" one uses a mini-display port plug only. So I'd be out of luck until there's display side adapter available. I am generally looking for a 16:10 or 4:3 rather than 16:9 monitor. It would be awesome if someone could find another, cheaper, monitor that isn't fronted by a plastic film, but rather with glass. It would be double awesome if said monitor was also 120hz so that I can use nVidia's 3D goggles. Update: One month and 16 days later I seem to not be the only one that can't find another glass based computer lcd monitor. LED backlighting is available though.

  Read the article

• Watchguard firebox: public IP addresses behind firewall with as much usable IP addresses as possible

  - by martinezpt

  Our ISP assigned us 16 public IP addresses that we want to assign to hosts behind a Watchguard firebox x750e. The IP addresses are: x.x.x.176/28 of which x.x.x.177 is the gateway. The hosts will be running software that needs to be directly assigned the public IP address so 1:1 NAT is not an option. I found this document that gives examples on how to assign public IP addresses to hosts behind the firewall, using an optional interface: http://www.watchguard.com/help/configuration-examples/public_IP_behind_XTM_configuration_example_(en-US).pdf However, I can't implement scenario 1 as it won't allow me to use the same subnet on both interfaces. As for scenario 2, splitting the address range into 2 subnets will decrease the usable hosts on the optional interface to 5 (8 - network - broadcast - optional interface ip). I'm convinced that there must be a better way to address this problem and maximize the number of usable IP addresses but I'm not very familiar with this specific firewall. Are there any suggestions on how to keep the hosts behind the firewall with public IP addresses while maximizing the usable IP addresses? thanks

  Read the article

< Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >