Search Results

Search found 5490 results on 220 pages for 'quick'.

Page 151/220 | < Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >

• switchless Infiniband between two servers on RHEL 6.3

  - by exfizik

  I have 2 servers running RHEL 6.3 which have 2 port Infiniband cards >lspci | grep -i infini 07:00.0 InfiniBand: QLogic Corp. IBA7322 QDR InfiniBand HCA (rev 02) I'm interested in connecting them directly to each other bypassing an Infiniband switch (which I don't have). Quick googling showed that at least in some configurations it's possible. I installed all RedHat Infiniband packages with yum groupinstall "Infiniband Support". However, ibv_devinfo shows that both ports in each card are down, which indicates that cables are not connected. But the cable is connected, although the LEDs are off on the cards (not a good sign). Another source of confusion for me is that according to this, RedHat doesn't come with OFED packages and I'm slightly hesitant to install them from source due to the lack of RedHat support for them... So where am I going with this? The questions I have are: is it possible to have a switchless/direct Infiniband connection between two servers the way I described above? If it's possible, do I have to use the OFED packages or can I configure everything with just the packages coming with RHEL. Why are the LEDs off on my servers even though the cable is connected? Any additional input/advice/pointers would be appreciated. P.S. I followed this guide for installation instructions. The Infiniband cards are clearly recognized by my OS and the rdma service is running. Update: I have opensm installed. When I run it it says: OpenSM 3.3.13 Command Line Arguments: Log File: /var/log/opensm.log ------------------------------------------------- OpenSM 3.3.13 Entering DISCOVERING state Using default GUID 0x1175000076e4c8 SM port is down and stays at that point.

  Read the article

• How to make DD-WRT router's (configured like a repeater) devices be accessible on LAN? (i.e. integrate DHCP for both routers)

  - by Annonomus Penguin

  I have a D-Link DIR-600-A1 router running DD-WRT (using the 601's firmware: except for the model number, they are near identical). It has an Atheros chip, so there is no "repeater" option. You can bypass this by setting the main radio as a client to the main router, and adding a virtual radio configured as an AP. You can then set up the credentials for connecting to the main router and allowing devices to connect to the repeater/router. I have a few devices on my network: Ethernet computers Server with Samba running WiFi devices connected to the main router I then wanted to add a repeater. I have a couple of other things on the repeater: WiFi Computer Other WiFi devices. Anyway, I wanted to connect my WiFi computer to the share on my server via Samba. However, for some reason, my router treats the main router as WAN, not another device. I've tried disabling the SPI firewall: However, that doesn't work. I've tried pinging my WiFi computer from my server. However, I can ping my server from my WiFi computer. AFAIK, they are on the same subset, just using different IPs: the main one uses 192.168.0.x and the repeater uses 192.168.1.x (starting at 100 for some reason). It seems as I need to configure my router(s) to work together for DHCP. I noticed there was a "DHCP forwarder" option, but I have no idea what that would do. A quick note: for some reason (that's beyond me) my ISP disabled the capability to bridge a WiFi to ethernet connection with the router they provide (something about PPPoE or similar...). The service rep I talked to when I was having issues after I changed ISPs said that, but they couldn't explain exactly what they were "blocking." How can I get DD-WRT to not treat the client connection as WAN and the router to recognize the devices connected to the repeater?

  Read the article

• Cannot start listening on a certain TCP port, but there's nothing currently listening on it

  - by John Rasch

  I have Windows Service that uses a WCF service host to listen for connections on TCP port 61000. When I try to start the service, I get the error: Service cannot be started. System.ServiceModel.AddressAlreadyInUseException: HTTP could not register URL http://+:61000/ because TCP port 61000 is being used by another application. ---> System.Net.HttpListenerException: The process cannot access the file because it is being used by another process at System.Net.HttpListener.AddAll() at System.Net.HttpListener.Start() at System.ServiceModel.Channels.SharedHttpTransportManager.OnOpen() --- End of inner exception stack trace --- at System.ServiceModel.Channels.SharedHttpTransportManager.OnOpen() at System.ServiceModel.Channels.TransportManager.Open(TransportChannelListener channelListener) at System.ServiceModel.Channels.TransportManagerContainer.Open(SelectTransportManagersCallback selectTransportManagerCallback) at System.ServiceModel.Channels.HttpChannelListener.OnOpen(TimeSpan timeout) at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout) at System.ServiceModel.Dispatcher.ChannelDispatcher.OnOpen(TimeSpan timeout) at... A quick netstat -a shows there is nothing listening on port 61000. I've also found several posts online that mention reserving namespaces using netstat, but the account that the service runs under has administrator privileges so that shouldn't be necessary. Any other ideas as to why I'm getting this message? This service is running on 64-bit Windows Server 2008 R2 Standard.

  Read the article

• RDP problem with Vista and Windows 7 destination

  - by MadBison

  I use a server a home to host a bunch of concurrently running Hyper-V VM's with different OS's and software for testing. I have Vista on the laptop, all latest SP's and patches. The server is Server 2008 R2, fully patched. The guests are a mix of XP, Vista, Server 2008 and Windows 7. If I connect to the Win XP or Server 2008 guest using RDP, it is always good. Very quick, no speed issues. If I connect to the Vista or Win 7 guests, the response time is so slow it is unusable. Usually 6 or 8 seconds, and at times it is to long to measure! This happens from both the laptop running Vista, and the server running Server 2008 R2. Does anyone know what the issue is with RDP on Vista and Windows 7 destinations? I did read this: http://blog.tmcnet.com/blog/tom-keating/microsoft/remote-desktop-slow-problem-solved.asp and that is not the problem I have applied that change to all PC's.

  Read the article

• Network Management Cable Labeling Techniques and their alternatives [closed]

  - by Alex

  Possible Duplicate: What is the most effective solution you used to label cables? Yes i know there are a lot of howtos and already answered questions about this topic, like this one: How do you organise the cables in your racks? Currently i am searching the web for different techniques (alternatives) for labeling the cables at the server racks and/or data centers. Unfortunately i do not have any experience with labeling/documentation of network cables in a large scale. As far as I could lookup by now the current labeling techniques are coloring and a self defined print-labeling technique (numbering, text) maybe also according to a standard which are usually used. I want to know if QR, RFID (ok RFID in a data center would be stupid due to the radio frequency wouldn't it be?), Barcodes or similar (??) have already been used by some administrators or why they did not consider such techniques at all? Too complicated (with QR scanner etc..) if you are in front of the cables and want to get quick feedback for what the cable is? What alternatives are out there? Advantages/Disadvantages? Best-Practice? I would appreciate any help on this topic, thank you! Regards, Alex

  Read the article

• nginx+mysql5 loadtesting configuration strangeness

  - by genseric

  i am trying to setup a new server running on debian6 and trying to make it work smooth under load. i ve used a wordpress site as a test object, and tried the configurations on http://blitz.io. when i increase the mysql max_connections from 50 to 200 lots of timeouts start to occur. but on 50 , no timeouts and pretty well response times. nginx configuration is fine , i tuned the config so i dont see errors. so i presume it's related to the other configuration options of my.cnf . i read some about options but still cant find what max_connections problem is all about. btw, the server has 16gb of ram and a fine i7 cpu. here is the current my.cnf [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] wait_timeout=60 connect_timeout=10 interactive_timeout=120 user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking bind-address = 127.0.0.1 key_buffer = 384M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 20 myisam-recover = BACKUP max_connections = 50 table_cache = 1024 thread_concurrency = 8 query_cache_limit = 2M query_cache_size = 128M expire_logs_days = 10 max_binlog_size = 100M [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M thanks in advance. i asked this question on SO but it's closed as off topic so i believe this is a SF question.

  Read the article

• IDE/PATA high-speed hard drive dock

  - by wfaulk

  I frequently need to access bare drives for backups and need a quick, high-speed way to deal with them. There are a multitude of SATA hard drive docks (for example), but I have a lot of IDE/PATA (hereafter "IDE") drives that I would like to be able to use similarly. There are IDE-to-SATA adapters so you can plug your IDE hard drive into a SATA port, so I don't see any reason why you couldn't use the same technology to have a native dock, yet none seems to exist. Now, I'm aware that 3.5" IDE drives do not have a specification for the layout of the connector, and therefore can't be slapped into a dock the same way a SATA drive could, but 2.5" PATA drives do. In fact, I'm not terribly interested in supporting 3.5" drives. It would be nice, but I deal with them far less frequently than 2.5" drives. Also, I'd very much like for the connection to the computer be faster than USB, preferably eSATA, I don't want to be spending time mounting a drive inside an enclosure, I don't want bare drives lying around with a cable hanging off of them, and I'd prefer a single dock rather than two. What seems like the ideal solution to me would be a regular SATA→eSATA dock and some sort of screwless adapter for IDE drives, but I'm open to any suggestions, regardless of my stated preferences, but which are, in some sort of order of preference: high-speed (faster than USB, at least) holder for drive (not just a cable) no complicated enclosure support for 3.5" IDE drives single dock Updates: Here's a 3.5" IDE to 3.5" SATA docking adapter that could be part of the solution. Weird. I figured that would be the impossible part. I was hoping to find something like this 2.5" to 3.5" SATA chassis that would take a 44-pin IDE drive internally. It looks like the Vantec EZ Swap EX comes awfully close. It has its own bay dock, but it looks like the SATA ports on the back are spaced properly, even if they're not aligned quite properly. Unfortunately, the proper position is at the very edge of the drive, which means that the docks' connectors are at the very edge of their recesses, which means there's no way to fit it in there.

  Read the article

• "Run As Administrator" on program right click failing and not launching program

  - by GONeale

  This problem lies within a relatively fresh x64 Windows 7 install ~4 weeks, but is also a problem I have seen on Windows Vista machines (x86 versions). Since the other day, any programs attempted to be launched via right clicking on a shortcut (.lnk)'s context menu and pressing - "Run As Administrator" for instance, in the Quick Launch/Jump List in Windows 7 has failed, screen has not dimmed, no UAC popup. In fact the program does not even load. There is no way around this unless I use the shortcut version from "All Programs" which appears to work, very strange? I have performed no major software installs, nothing out of the ordinary. Has anybody encountered this or know what would be causing it? Here's an example of somebody else experiencing this problem in Vista with no solution: http://www.vistax64.com/vista-general/131918-strange-run-administrator-problem.html and I believe this problem is related, I also cannot right click - "Manage" on my computer): http://windows7forums.com/windows-7-support/5501-run-administrator-broken.html I am running the latest version of Avira AntiVir Virus Scanner and pretty concious of what I download, I don't think it is a virus, nor do I believe it is due to the RC Version of Windows 7, because I have seen the problem across multiple Operating Systems versions. Thanks guys.

  Read the article

• AD server within another network - DNS issues

  - by Harry Muscle

  Here's a quick summary of the environment I support: we have a domain (domain A) that has about 20 client computers. The domain server for this domain and all the clients sit within the network infrastructure of a larger domain (domain B). All the computers get their network settings via DHCP from domain B's servers. I have no control and am unable to make changes to anything to do with domain B. The problem I have is that currently in order for my domain's (domain A) clients to be able to resolve the domain server and the shares on it they have their DNS server IP address set to domain A's domain server (via the default GPO). Unfortunately when a laptop (windows and mac) gets taken home, they are still looking for the domain server as their DNS server and obviously can't access the internet correctly outside of our environment. Ideally I need a solution where the machines use domain A's domain server as their DNS when inside the office and use what ever DNS server DHCP gives them when they are outside the office. However, since I have no control over the office DHCP server, I'm not sure how this can be accomplished. Any help and advice that anyone can offer is highly appreciated. Thanks, Harry P.S. The solution I'm trying to find needs to require no involvement from the user.

  Read the article

• Weird .#filename files on remote ssh-connected systems after mcedit

  - by etranger

  I'm using MacFusion sshfs in combination with Midnight Commander, and when I edit remote text files with mcedit, weird symlinks are created on the remote system. $ ls -l .* lrwxr-xr-x 1 user group 34 Jun 27 01:54 .#filename.txt -> [email protected] where etranger is my local login name, and mbp is a hostname of my notebook running MacOS. symlinks can be removed by running remote rm command, but cannot be deleted on the mac-fuse mounted volume and thus pollutes the filesystem. I cannot figure what part of software is responsible for this, and how I could fix this, any help is appreciated. EDIT: This appears to be mcedit behavior as documented here: https://dev.openwrt.org/ticket/8245 Apparently, sshfs fails to remove symlink to the lock file for some reason (".#" in filename, perhaps), and it pollutes the filesystem. A quick workaround is possible, using another bug of Midnight Commander: editing (F4) the broken symlink effectively converts it to a missing lock file it was supposed to point to, and removes the symlink itself. The newly created file may then be deleted normally. EDIT 2: Unchecking "Follow symlink" in MacFusion apparently allows sshfs to remove dead symlinks, so the problem disappears completely.

  Read the article

• HP LaserJet 2550 has a carousel motor error

  - by Arlen Beiler

  I have a LaserJet 2550, and it's worked pretty good for a long time (except for some slowness a while back, spooling I think), but just recently it suddenly quit working. We moved this summer, but left it at our other place, and just recently when my Dad went over there to try to print something out, it didn't work. When you turn it on, you hear the fan give a false start (basically a quick pulse), and the carousel goes through its usual thing. Then it starts up in earnest like it's getting ready to print something. All of a sudden it just stops. Everything stops, and the three lower lights are steady. When I push the Go button, the Go light (bottom of the 3) turns off, but the other two stay on. I looked it up on the HP website and it says it is a carousel motor problem. I called HP, but they said it is out of warranty. I've opened the cover and held the switch with a screw driver so I could watch it, and it goes through its thing like I described (doesn't seem to make a difference whether the imaging drum is in or not), then when it stops it kind of seems to jump back a little bit (the carousel). I hope this all makes sense (I know you like details), and hopefully you also know what to do to fix it. Thanks.

  Read the article

• Advice needed for a home network setup (hardware & software) to handle many clients and potentially heavy traffic

  - by posdef

  I have recently decided to re-structure the home network of our flatshare here. Here's a quick outline of the situation. I envision to have the following 4 devices connected to the router via cable: Xbox 360 IP phone Printer QNAP server (Web, File and Multimedia) We are three people living here, so on top of that there will be to 5-6 computers/mobile devices connecting as wireless clients. My goal is to be able to transfer files (when needed) between the computer and the Multimedia server, which I can reach via 360 and play on the TV. I also would like to keep a high level of security; right now I have the encryption on WPA2 and MAC filtering. I don't believe the web server will get heavy traffic, though I would like to have it responsive. Likewise, I don't have a habit of downloading via torrent etc, but I greatly appreciate my network being responsive and fast, especially when I am browsing or streaming high quality media. Now my questions are: is this setup feasible? smart? efficient? can this be improved somehow? my current router (D-Link DI624) and the previous one (DI-524) used to have spontaneous drops in network, which I find highly irritating. I don't believe in my router, especially now that it completely crashed when I was test-running the setup by transferring a large media file to server while xbox was playing music from the server, and two computers browsing the net. Do I need to get new hardware, if so, any recommendations for a reliable and fast router?

  Read the article

• HDD cannot be booted from

  - by K.Wong

  I have an ASUS A52F, no mods, with Win7 preinstalled. There is one hard drive, two partitions, one for the OS (C:) and one for data (D:) After laptop trauma, i.e. I dropped it, it still worked fine. However, when chkdisk was run on the C: drive chkdisk crashed, and Windows is unbootable. Windows Startup Manager utility was run, but error code 0xc00000e9 was given. Windows help db shows that this is a BIOS problem, however in BIOS setup the drive can be accessed, and folders can be shown. I also burned a Ubuntu 12.04 distro, and booted off it, but my internal HDD is missing and cannot be accessed. When installation program is run the HDD shows up as a location to install to yet the drive is shown as blank. tl;dr: HDD damaged, chkdisk crashed. Windows 7 is unbootable. Given error code, according to Microsoft db, is a BIOS problem, yet in BIOS the drive is accessible. different OS (Ubuntu 12.04), booted off a distro, yet HDD is inaccessible. Quick help appreciated.

  Read the article

• Intel Rapid Storage Technology (pre-OS) driver installation

  - by Nero theZero

  My desktop machine is built on Gigabyte GA-Z87-UD3H and Gigabyte provides the latest driver for Intel Rapid Storage Technology (IRST), which I installed after installing the OS. Same goes for my Lenovo Thinkpad-T420. And for both machine, checking the controller device under the IDE ATA/ATAPI Controllers section in Device Manager I see the driver has been updated to the latest version. I set the SATA controller to AHCI from BIOS On the desktop machine I have one WD 2TB BLACK & one WD 3TB Green I don’t use RAID, & no chance of using in near future, but according to Intel IRST improves performance in single disk scenario too. Now I have the following questions – What is the actual purpose of IRST (pre-OS install) driver that doesn’t get served with a post-OS driver that I installed? There must be some difference, otherwise there wouldn’t be a pre-OS version of the driver. Right? In the pre-OS procedure (loading the drivers at OS-installation time) after successfully completing the OS installation, do I need that post-OS driver? Because after installing from that one I got a quick launch icon that runs the IRST configuration application. Where do get that after installing the pre-OS driver? As it is “pre-OS”, when I load it at OS-installation time, does it updates anything at BIOS level or anywhere other than HDD? That’s because I’m going to dual boot Windows 7 with Windows 8.1, and after installing Windows 7 when I install Windows 8.1 & load the IRST driver for that, is there any chance of any “overwriting” or OS-incompatibility? In short, is there anything specific to follow while installing the second OS?

  Read the article

• Dell Poweredge 1950 with Perc 5i keeps losing raid config -> "Foreign Configuration Found"

  - by nosage

  The quick and dirty: the machine is a Dell Poweredge 1950, dual xeon quad cores, 8GB of ram, 2 2TB seagate SATAs in (supposed to be raid1) using a Perc 5i raid card. They are hot-swappable with a back-plane. I can build the raid fine and after a little while an install of server 08 r2 will blue screen and restart. When it comes up the raid controller says "Foreign Configuration Found." When I go into the raid configuration panel there is no raid listed but I can import the "foreign config", and the OS will boot up fine, until it blue screens again after a little while. The issue is OS independent. I have tried swapping raid cards, swapping the RAM module on the raid card and swapping the raid battery, all to no avail. Its almost as if there is a loose connection from the raid card to the back plane and both of disks get lost and the raid card drops the config. But it sees the disks fine when it boots back up. The raid card uses a SCSI SAS cable to connect to the back-plane so I guess the next step is to replace that, but... then I might as well replace the back-plane with a SCSI SAS to sata breakout cable, but... then I need a way to power the disks. Sorry for the wall of txt but it would be great to get some thoughts from people who worked with perc raid cards or poweredge servers with this type of issue before. Ironically I want to get this system up and running so I can work on MCITP labs. Thank you for any/all help and feel free to ask questions!

  Read the article

• How to generate thumbnails for less common video containers (mkv, ogm, mp4, flv, rmvb and mov) in wi

  - by fluxtendu

  So how to generate thumbnails for these containers? I know that the install of "DivX Plus Tech Preview: MKV on Windows 7" does it for MKV. But I think that only some registry changes are really necessary and I want it for other containers. If it's possible to avoiding the install of (always bloated) codecs packs it would be nice... Maybe only installing ffdshow or essential and separated codecs. (some time ago I have try reg files for vista without success...) Update: I have installed Win7codecs & tweaked a little its settings and I got almost everything I want. (I have also re-installed the relevant part of the divx plus tech preview to get something else than an all black preview for MKV) Issues that I still want to resolve: Find a cleaner & lighter method Almost all my rmvb and mov files got an all black preview (installing real media/quick time alternative doesn't help, is it the same with the officials?) With almost all containers (avi, mkv, ogm, mpg), I have (few) random files that don't get the preview. I could play them in WMP or another player and don't have found a pattern in the codecs used. All wmv, flv and mp4 have previews but I have less files in these containers. (I clear my thumbnails cache to test them) More generally I would like to understand how windows handle the containers & codecs to generate the previews. And a software that let me choose arbitrarily the pictures previewed would be convenient too

  Read the article

• Ubuntu 10.04 Keyboard and Mouse Freezing Problem

  - by nitbuntu

  I had a partition setup with Windows XP and Ubuntu 8.04 dual booting. I recently upgraded to Ubuntu 10.04 by installing fresh from CD but leaving the previous /home folder as is. Things seemed to be working fine, but started finding that my mouse and keyboard were freezing. After a quick search on the internet, I found the following suggestions as shown here:- Ubuntu Forums Here the suggestion was to:- Edit /etc/default/grub, go to the line that begins like: GRUB_CMDLINE_LINUX_DEFAULT= Change it to: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi=off" After that, run this command: sudo update-grub and Reboot This seemed to have resolved the issue but after a couple of days I again find my mouse and keyboard freezing. I also find that my parallel port printer had also stopped working. I have saved the output of dmesg and my syslog. The first can be viewed here but the syslog had too many characters, so if someone can suggest an alternative to freetexthost, I can post it there. Moreover, if there is any other information that should be provided, do let me know. I do hope we can get to the bottom of this issue. Thank you in advance for any help that could be provided.

  Read the article

• On dual boot system, Is it possible to use VirtualBox to boot other installed OS?

  - by Derek Ziemba

  I currently run Windows 7 from a 256GB SSD as my Operating System. Lately, for school, I've been using openSUSE linux inside a VirtualBox PC and I'm really liking it. I'm starting to hate even working in Windows. But I can't just abandon Windows. I've been considering dual booting openSUSE and will likely purchase another SSD for openSUSE. Once I have the dual boot set-up, there is going to be times I need to do something quick in the operating system that I'm not currently in. It would be a pain to have to reboot the computer each time I need to switch the OS for a simple task, especially from Windows since it doesn't let you save it's state. From openSUSE, I want to be able to start a VirtualBox Machine using my Windows Drive. And in Windows, I want to be able to start a VirtualBox Machine of my openSUSE Drive. Would this be possible? The issue I'm worried about is drivers. For instance, the OS will be installed on native hardware and have the native hardware's drivers configured. When I try to boot the OS in a VirtualMachine, I feel like the OS is not going to know what to do, and have to reconfigure itself or just not work.

  Read the article

• Data recovery on a corrupted 3TB disk

  - by Mark K Cowan

  Short version I probably need software to run a deep-scan recovery (ideally on Linux) to find files on NTFS filesystem. The file data is intact, but the references are no longer present. Analogous to recovering data from a "quick-formatted" partition. Hopefully there is a smarter way available than deep-scan, one which would recover filenames and possibly paths. Long version I have a 3TB disk containing a load of backups. Windows 7 SP1 refused to detect the disk when plugged in directly via SATA, so I put it on a USB/SATA adaptor which seemed to work at first. The SATA/USB adaptor probably does not support disks over 2.2TB though. Windows first asked me if I wanted to 'format' the disk, then later showed me most of the contents but some folder were inaccessible. I stupidly decided to run a CHKDSK on my backup disk, which made the folders accessible but also left them empty. I connected this disk via SATA to my main PC (Arch Linux). I tried: testdisk ntfsundelete ntfsfix --no-action (to look for diagnostically relevant faults, disk was "OK" though) to no avail as the files references in the tables had presumably been zeroed out by CHKDSK, rather than using a typical journal'd deletion). If it is useful at all, a majority of the files that I want to recover are JPEG, Photoshop PSD, and MPEG-3/MPEG-4/AVI/MKV files. If worst comes to worst, I'll just design my own sector scanner and use some simple heuristic-driven analysis to recover raw binary blocks of data from the disk which appears to match the structures of the above file types. I am unfamiliar with the exact workings of NTFS but used to be proficient at recovering FAT32 systems with just a hex-editor, so I can provide any useful diagnostic information if you let me know how to find it! My priorities in ascending order of importance for choosing the accepted answer: Restores directory structure Recovers many filenames in addition to the file data Is free / very cheap Runs on Linux Recovers a majority of file data The last point is the most important, but the more of the higher points you match the more rep you'll probably get :)

  Read the article

• Filtered Router Interface

  - by jviotti

  I'm having some problems with a Scientific-Atlanta DPR2320R2. In specific with the WIFI. A few months ago I changed its password and username and now I can't remember. So I tried cracking it with Hydra but it drove things worse. Content of webadmin was rendered partial, and threw lot of errors. I then reseted the router. I found myself abled to browse the web with ethernet-connected pc. Wifi is configured by registering the device's MAC Address, and indeed the router has been reseted and register MAC address were lost. No device could connect to wifi. In fact, the device does not even recognize the network. I tried the pointing to 192.168.0.1 to restablish the MAC's. But I couldn't connect to the router access point. Tried listing up hosts: $ nmap -sP 192.168.0.0/24 Starting Nmap 5.00 ( http://nmap.org ) at 2012-12-11 01:18 ART Host 192.168.0.1 is up (0.0018s latency). Host 192.168.0.11 is up (0.00025s latency). Nmap done: 256 IP addresses (2 hosts up) scanned in 59.62 seconds Then checked 192.168.0.1 was really up by sending pings. It responded to all my pings. I quick-scanned the access point: $ nmap 192.168.0.1 Starting Nmap 5.00 ( http://nmap.org ) at 2012-12-11 01:08 ART Interesting ports on 192.168.0.1: Not shown: 999 closed ports PORT STATE SERVICE 80/tcp filtered http Nmap done: 1 IP address (1 host up) scanned in 6.73 seconds Look the state of the port 80: FILTERED. I'm pretty confused now. Any suggestion would be appreciated. Thanks in advance.

  Read the article

• Google Maps mashup for notes/househunting

  - by afray

  I'm house-hunting at the moment and I'm trying to geek it out er I mean streamline the decision-making process. I'm currently using google maps's "my maps" feature to store pins to properties. I create one map per estate agent, then put relevant into into the individual pins. The idea being, I can look at the map and quickly choose which property to view next. However the pins don't currently link back to the map they're owned by, so you have to hunt a bit to get the estate agent info, it's a hassle to get all maps displayed in a new session if you have lots of agents, and each pin doesn't automatically show its bubble so you have to do lots of clicking to see all the info you want. I've tried Evernote, but despite its tag system initially showing some promise, I can't find a way to seemlessly integrate maps. A few google searches don't turn anything up either. Even the big sites, like http://www.rightmove.co.uk, don't seem to provide any maps integration by default. You can see an individual house's location, but not all results of a search. So is there a web site or windows program I could use to do something like this? Viewing all properties on a map is a must, as is quick access to contact details.

  Read the article

• Resource Monitor (resmon) in Windows Server 2008 R2

  - by Clever Human

  In Windows Server 2008 R2's Resource Monitor, is there a way to set the scale of the various graphs to be constant values instead of variable based on data? It seems to me that the utility of a graph is to get a quick overview glance at the values those graphs are showing. So if I look at the CPU graph and the line is up near the top, I can know immediately that something is using all my CPU and go investigate what. I don't really care if the CPU is jumping between .01% and 2%. Or if the network usage monitor is up near the top, I will know that all my bandwidth is being used up, and go figure out what. But the way things are now, the graphs are meaningless because the scales constantly shift. If you look at the network usage graph in one second it might have a scale out of 100kbps, and the next second have a scale based on 1mbps! So... is there a registry key or something that will peg the scale of these graphs to logical maximums? (the graph on the right hand side of the screenshot below):

  Read the article

• Different versions of iperf for windows give totally different results

  - by Albert Mata

  Measuring TCP output from a Windows client to Solaris server: WXP SP3 with iperf 1.7.0 -- returns an average around 90Mbit Same client, same server but iperf 2.0.5 for windows -- returns an average of 8.5 Mbit Similar discrepancies have been observed connecting to other servers (W2008, W2003) It's difficult to get to some conclusions when different versions of the same tool provide vastly different results. Example below: C:\tempiperf -v (from iperf.fr) iperf version 2.0.5 (08 Jul 2010) pthreads C:\tempiperf -c solaris10 Client connecting to solaris10, TCP port 5001 TCP window size: 64.0 KByte (default) [ 3] local 10.172.181.159 port 2124 connected with 10.172.180.209 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.2 sec 10.6 MBytes 8.74 Mbits/sec Abysmal perfomance, but now I test from the same host (Windows XP SP3 32bit and 100Mbit) to the same server (Solaris 10/sparc 64bit and 1Gbit running iperf 2.0.5 with default window of 48k) with the old iperf C:\temp1iperf -v iperf version 1.7.0 (13 Mar 2003) win32 threads C:\temp1iperf.exe -c solaris10 -w64k Client connecting to solaris10, TCP port 5001 TCP window size: 64.0 KByte [1208] local 10.172.181.159 port 2128 connected with 10.172.180.209 port 5001 [ ID] Interval Transfer Bandwidth [1208] 0.0-10.0 sec 112 MBytes 94.0 Mbits/sec So one iperf with a 64k window says 8.75Mbit and the old iperf with the same window size says 94.0Mbit. These results are constant through repeated tests. From my testing launching iperf(old) with window size "x" and iperf(new) with window size "x" instead of producing the same or very close results produce totally different results. The only difference I see is the old compiled as win32 threads vs. pthreads but parallelism (-P 10) appears to work in both. Anyone has a clue or can recommend a tool that gives results I can trust?? EDIT: Looking at traces from (old) iperf it sets the TCP Window Scale flag to 3 in the SYN packet, when I run the (new) iperf this is set to 0 in the initial packet. A quick analysis of the window size through the exchange shows the (old) iperf moving back and forth but mostly at 32k while the (new) iperf mostly keeps at 64k. Maybe it will help somebody to connect the dots.

  Read the article

• Strange ASP.NET Queue Performance Counters Behavior?

  - by LemurTech

  We have an ASP.NET 2.0 site running in classic mode. I am seeing very strange behavior in the performance counter values. Perhaps these are bugs (I've been all over Google trying to verify this, without much luck), or perhaps it is just my inexperience with monitoring these things. This PerfMon graph (http://imgur.com/Jv5io5J) represents a load test where I add up to 350 virtual users to the site, at a rate of about 1/sec, performing relatively simple page browsing. At the end of the test, I gradually taper off the number of users. This is a 4 CPU server. Machine.config settings for are at the defaults. The solid blue line is ASP.NET Apps v2.x\Requests Executing for the application in question. The profile makes perfect sense, with a quick ramp-up to 32 executing requests (minWorkerThreads x 4CPUs), followed by a slower ramp-up to 48 ((maxWorkerThreads - minWorkerThreads) x 4CPUs). The solid yellow line is ASP.NET v2.x\Requests Queued. Again, this makes sense: after the initial 32 request threads are activated, the queue begins to build as new thread initialization can't keep pace with incoming requests. But as executing requests reaches its highest possible value of 48, the counter for ASP.NET Apps v2.x\Requests Queued (green solid line) suddenly springs to life and maintains step with the yellow counter. As far as I can tell, and with no other apps running on the server, these two counters should have had the same values from the start. One other odd thing: The counter for ASP.NET v2.x\Request Wait Time (dotted yellow line) also does not spring to life until executing requests reaches 48. Shouldn't I be seeing values here from the moment ASP.NET v2.x\Requests Queued begins to build? And likewise, why would ASP.NET Apps v2.x\Request Execution Time (dotted blue) increase significantly only after that peak of 48 is reached? Shouldn't it ramp-up gradually along with queued requests?

  Read the article

• Python coding with VLC player (quite a basic query I expect)

  - by Todd

  I'm fairly new to the whole coding realm so my knowledge is fairly limited, and I can't seem to find any basic tutorials on how to use scripts with VLC player. More specifically, the reason I'm asking here is because I stumbled across a post on this site about playing random clips from random videos on VLC player automatically. This is the forum post: Playback random section from multiple videos changing every 5 minutes My situation is similar to this lovely gentleman's was, though he clearly knows a lot more about coding than I do. In short, I'd like to copy this coding into a file of some sort and apply it to VLC player myself. Only I'm not sure what file type I'd have to save it as (I have Python by the way, and I tried saving it as a .py file but I didn't know if it was correct or where to go from there). Additionally, I'm not sure how to get VLC to "read" the script, so to speak - is there a specific location the file needs to be, and do I run the script from another program or through VLC? I'll reiterate that I'm relatively new to this, so if anybody would be so kind as to post a quick list of steps on how to save/place the file and use it with VLC player I really would appreciate it! P.S. I'm not computer illiterate, I'm fine with most programs and I'd understand if you just said things like "C:\Program Files (x86)\VideoLAN\VLC\plugins" or "in VLC, select Tools Plugins and extensions", I just wouldn't catch on to anything about adding a line of coding that does something without being told exactly what to write! Many thanks in advance! :) Todd

  Read the article

< Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >