Search Results

Search found 11797 results on 472 pages for 'fedora 12'.

Page 152/472 | < Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >

  • Linux on Sony Vaio VPCEB1S1E

    - by Jaakko
    I bought Sony Vaio VPCEB1S1E and I was able to surf on net. Then I tried to install Ubuntu 9.04 and Linux Mint on it but neither allows me an access to the Internet. How can I configure Mint so that I can go to net and get updates via apt-get? jaakko@jaakko-laptop ~ $ ifconfig -a lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) pan0 Link encap:Ethernet HWaddr 46:83:d4:f4:36:bc BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 78:dd:08:c5:61:88 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster0 Link encap:UNSPEC HWaddr 78-DD-08-C5-61-88-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) jaakko@jaakko-laptop ~ $ ping 8.8.8.8 connect: Network is unreachable

    Read the article

  • Force netsh/arp binding multicast IP addres with specific MAC address

    - by Olivier
    I would like to setup an binding from an IP address to a MAC address using netsh. Goal is to bond an IP address which is a multicast address (224.224.x.y) to a given MAC address (which is NOT the calculated one from the multicast IP address : 01:00:5e:X:Y:Z It used to work with Windows XP (was it a bug that used to be "perfect" for my needs?), but Windows 7/8/8.1 forces the MAC address to the calculated one instead of letting me put what I want! (http://nettools.aqwnet.com/ipmaccalc/ipmaccalc.php shows MAC address calculation for multicast IP address) Thus I'm doing the following. Listing existing mappings: netsh.exe interface ip show neighbors "Ethernet" Interface 12 : Ethernet Internet address Physical address Type 224.0.0.22 01-00-5e-XX-YY-ZZ static Then adding my interface mapping manually: netsh.exe interface ip add neighbors "Ethernet" "224.xxx.yyy.zzz" "00-80-EE-UU-VV-WW" Finally, listing again my mappings: netsh.exe interface ip show neighbors "Ethernet" Interface 12 : Ethernet Internet address Physical address Type 224.0.0.22 01-00-5e-XX-YY-ZZ static **224.xxx.yyy.zzz 01-00-5e-UU-VV-WW static** As you can see, the MAC Address of the second entry (the one I just made) has been dynamically replaced by the calculated MAC Address corresponding to my IP Address... Calculation is done as follow (and displayed in hexa): UU=(xxx-128) VV=yyy WW=zzz But I don't want that behavior. My IP address and MAC address cannot be changed, and I must associate them accurately. Does anybody know how to disable MAC address substitution/calculation in netsh? Thanks, Olivier.

    Read the article

  • Is there any way for ME to improve routing to an overseas server?

    - by Simon Hartcher
    I am trying to make a connection to a gaming server in Asia from Australia, but my ISP routes my connection through the US. Tracing route to worldoftanks-sea.com [116.51.25.54]over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 192.168.1.1 2 34 ms 42 ms 45 ms 10.20.21.123 3 40 ms 40 ms 43 ms 202.7.173.145 4 51 ms 42 ms 36 ms syd-sot-ken-crt1-ge-6-0-0.tpgi.com.au [202.7.171.121] 5 175 ms 200 ms 195 ms ge5-0-5d0.cir1.seattle7-wa.us.xo.net [216.156.100.37] 6 212 ms 228 ms 229 ms vb2002.rar3.sanjose-ca.us.xo.net [207.88.13.150] 7 205 ms 204 ms 206 ms 207.88.14.226.ptr.us.xo.net [207.88.14.226] 8 207 ms 215 ms 220 ms xe-0.equinix.snjsca04.us.bb.gin.ntt.net [206.223.116.12] 9 198 ms 201 ms 199 ms ae-7.r20.snjsca04.us.bb.gin.ntt.net [129.250.5.52] 10 396 ms 391 ms 395 ms as-6.r20.sngpsi02.sg.bb.gin.ntt.net [129.250.3.89] 11 383 ms 384 ms 383 ms ae-3.r02.sngpsi02.sg.bb.gin.ntt.net [129.250.4.178] 12 364 ms 381 ms 359 ms wotsg1-slave-54.worldoftanks.sg [116.51.25.54] Trace complete. Since I think it will be unlikely that my ISP will do anything, are there any ways to improve my routing to the server without them having to intervene? NB. The game runs predominately over UDP, so I believe most low ping services are out of the question, as they rely on TCP traffic.

    Read the article

  • What used the linux memory? Low cache, low buffer, not a VM

    - by Jason
    First of all, yes, I have read LinuxAteMyRAM, which doesn't explain my situation. # free -tm total used free shared buffers cached Mem: 48149 43948 4200 0 4 75 -/+ buffers/cache: 43868 4280 Swap: 38287 0 38287 Total: 86436 43948 42488 # As shown above, the -/+ buffers/cache: line shows indicates the used memory rate is very high. However, from output of top, I don't see any process used more than 100MB of memory. So, what used the memory? PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 28078 root 18 0 327m 92m 10m S 0 0.2 0:25.06 java 31416 root 16 0 250m 28m 20m S 0 0.1 25:54.59 ResourceMonitor 21598 root -98 0 26552 25m 8316 S 0 0.1 80:49.54 had 24580 root 16 0 24152 10m 760 S 0 0.0 1:25.87 rsyncd 4956 root 16 0 62588 10m 3132 S 0 0.0 12:36.54 vxconfigd 26703 root 16 0 139m 7120 2900 S 1 0.0 4359:39 hrmonitor 21873 root 15 0 18764 4684 2152 S 0 0.0 30:07.56 MountAgent 21883 root 15 0 13736 4280 2172 S 0 0.0 25:25.09 SybaseAgent 21878 root 15 0 18548 4172 2000 S 0 0.0 52:33.46 NICAgent 21887 root 15 0 12660 4056 2168 S 0 0.0 25:07.80 SybaseBkAgent 17798 root 25 0 10652 4048 1160 S 0 0.0 0:00.04 vxconfigbackupd This is an x86_64 machine (not a common-brand server) running x84_64 Linux, not a container in a virtual machine. Kernel (uname -a): Linux 2.6.16.60-0.99.1-smp #1 SMP Fri Oct 12 14:24:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Content of /proc/meminfo: MemTotal: 49304856 kB MemFree: 4066708 kB Buffers: 35688 kB Cached: 132588 kB SwapCached: 0 kB Active: 26536644 kB Inactive: 17296272 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 49304856 kB LowFree: 4066708 kB SwapTotal: 39206624 kB SwapFree: 39206528 kB Dirty: 200 kB Writeback: 0 kB AnonPages: 249592 kB Mapped: 52712 kB Slab: 1049464 kB CommitLimit: 63859052 kB Committed_AS: 659384 kB PageTables: 3412 kB VmallocTotal: 34359738367 kB VmallocUsed: 478420 kB VmallocChunk: 34359259695 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 Hugepagesize: 2048 kB df reports no large consumption of memory from tmpfs filesystems.

    Read the article

  • Why is my RapidSSL Certificate chain is not trusted on ubuntu?

    - by olouv
    I have a website that works perfectly with Chrome & other browser but i get some errors with PHP in CLI mode so i'm investigating it, running this: openssl s_client -showcerts -verify 32 -connect dev.carlipa-online.com:443 Quite suprisingly my HTTPS appears untrusted with a Verify return code: 27 (certificate not trusted) Here is the raw output : verify depth is 32 CONNECTED(00000003) depth=2 C = US, O = GeoTrust Inc., CN = GeoTrust Global CA verify error:num=20:unable to get local issuer certificate verify return:1 depth=2 C = US, O = GeoTrust Inc., CN = GeoTrust Global CA verify error:num=27:certificate not trusted verify return:1 depth=1 C = US, O = "GeoTrust, Inc.", CN = RapidSSL CA verify return:1 depth=0 serialNumber = khKDXfnS0WtB8DgV0CAdsmWrXl-Ia9wZ, C = FR, O = *.carlipa-online.com, OU = GT44535187, OU = See www.rapidssl.com/resources/cps (c)12, OU = Domain Control Validated - RapidSSL(R), CN = *.carlipa-online.com verify return:1 So GeoTrust Global CA appears to be not trusted on the system (Ubuntu 11.10). Added Equifax_Secure_CA to try to solve this... But i get in this case Verify return code: 19 (self signed certificate in certificate chain) ! Raw output : verify depth is 32 CONNECTED(00000003) depth=3 C = US, O = Equifax, OU = Equifax Secure Certificate Authority verify error:num=19:self signed certificate in certificate chain verify return:1 depth=3 C = US, O = Equifax, OU = Equifax Secure Certificate Authority verify return:1 depth=2 C = US, O = GeoTrust Inc., CN = GeoTrust Global CA verify return:1 depth=1 C = US, O = "GeoTrust, Inc.", CN = RapidSSL CA verify return:1 depth=0 serialNumber = khKDXfnS0WtB8DgV0CAdsmWrXl-Ia9wZ, C = FR, O = *.carlipa-online.com, OU = GT44535187, OU = See www.rapidssl.com/resources/cps (c)12, OU = Domain Control Validated - RapidSSL(R), CN = *.carlipa-online.com verify return:1 Edit Looks like my server does not trust/provide the Equifax Root CA, however i do correctly have the file in /usr/share/ca-certificates/mozilla/Equifax...

    Read the article

  • How can I get the root account to generate an acceptable ssh key?

    - by Jamie
    On an ubuntu machine I did the following: ~$ sudo su - [sudo] password for jamie: root@mydomain:~# ssh-keygen -t rsa Generating public/private rsa key pair. Enter file in which to save the key (/root/.ssh/id_rsa): Enter passphrase (empty for no passphrase): Enter same passphrase again: Your identification has been saved in /root/.ssh/id_rsa. Your public key has been saved in /root/.ssh/id_rsa.pub. The key fingerprint is: 12:34:56:78:9a:bc:de:f0:12:34:56:78:9a:bc:de:f0 [email protected] The key's randomart image is: +--[ RSA 2048]----+ | | | | | | | | | | | | | | | | | | +-----------------+ root@mydomain:~# cat /root/.ssh/id_rsa.pub | ssh -p 443 [email protected] 'cat > authorized_keys' [email protected]'s password: root@mydomain:~# ssh -p 443 [email protected] [email protected]'s password: It's asking me for a password. However, using a regular account, the following works: $ cd ; ssh-keygen -t rsa ; cat ~/.ssh/id_rsa.pub | ssh [email protected] 'cat >> ~/.ssh/authorized_keys' $ ssh [email protected] Last login: Thu Oct 24 14:48:41 2013 from 173.45.232.105 [[email protected] ~]$ Which leads me to believe it's not an issue of authorized_keys versus authorized_keys2 or permissions. Why does the 'root' account accessing the remote 'jamie' account not work? The remote machine is CentOS if that's relevant.

    Read the article

  • how to grep ip from ifconfig output

    - by Registered User
    Following is my ifconfig output eth0 Link encap:Ethernet UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:28 Base address:0x2000 eth1 Link encap:Ethernet inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:36497 errors:0 dropped:0 overruns:0 frame:14515 TX packets:44884 errors:1352 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:20781745 (20.7 MB) TX bytes:17776225 (17.7 MB) Interrupt:17 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) virbr0 Link encap:Ethernet inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:4416 (4.4 KB) vmnet1 Link encap:Ethernet inet addr:192.168.185.1 Bcast:192.168.185.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) vmnet8 Link encap:Ethernet inet addr:192.168.207.1 Bcast:192.168.207.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) I want to do some thing grep that I see the IP corresponding to each LAN card? Is that possible? How can it be achieved?

    Read the article

  • simple network between xp & 7 with cross cable problem...

    - by LostLord
    hi my dear friends : i have a simple network between xp & 7 windowses with cross cable (2 pc home)... ===================================================================== the one with 7 is mother and have 2 lan device (onboard + pci) A. onboard is like this when u go to tcp/ip v4 properties:(4 adsl internet) obtain an ip... preferred dns server : 81.91.129.67 alternate dns server : 4.2.2.4 shared...no permission 4 change so every thing is ok for internet on windows 7. B. the other lan pci card that is connected to pc with xp is like this : 192.168.2.11 255.255.255.0 0.0.0.0 empty empry computer name : cougar workgroup : nethome homeNetwork is disabled (i think that is 4 2 pc's with 7 os not xp) every thing is off in network options except file & printer sharing in public area ===================================================================== pc with xp os is like this : 192.168.2.12 255.255.255.0 192.168.2.11 (mean gateway) 4.2.2.4 8.8.8.8 computer name : tiger workgroup : nethome ===================================================================== at last my little net is ok... mean both have internet , both can see each other by their ip (\\192.168.2.11 or \\192.168.2.12) my problem is when in pc with xp type \\cougar it shows an error about network path! but in pc with 7 \\tiger works perfec. what is the problem in system with xp ? in few days ago this network was ok (search by computer name) when both os were xp , so there is no problem with my cable or devices. another problem is i can not find tiger in my network list in 7 pc \ why? is something wrong with my network? thanks 4 future advance best regards

    Read the article

  • Locating memory leak in Apache httpd process, PHP/Doctrine-based application

    - by Sam
    I have a PHP application using these components: Apache 2.2.3-31 on Centos 5.4 PHP 5.2.10 Xdebug 2.0.5 with Remote Debugging enabled APC 3.0.19 Doctrine ORM for PHP 1.2.1 using Query Caching and Results Caching via APC MySQL 5.0.77 using Query Caching I've noticed that when I start up Apache, I eventually end up 10 child processes. As time goes on, each process will grow in memory until each one approaches 10% of available memory, which begins to slow the server to a crawl since together they grow to take up 100% of memory. Here is a snapshot of my top output: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1471 apache 16 0 626m 201m 18m S 0.0 10.2 1:11.02 httpd 1470 apache 16 0 622m 198m 18m S 0.0 10.1 1:14.49 httpd 1469 apache 16 0 619m 197m 18m S 0.0 10.0 1:11.98 httpd 1462 apache 18 0 622m 197m 18m S 0.0 10.0 1:11.27 httpd 1460 apache 15 0 622m 195m 18m S 0.0 10.0 1:12.73 httpd 1459 apache 16 0 618m 191m 18m S 0.0 9.7 1:13.00 httpd 1461 apache 18 0 616m 190m 18m S 0.0 9.7 1:14.09 httpd 1468 apache 18 0 613m 190m 18m S 0.0 9.7 1:12.67 httpd 7919 apache 18 0 116m 75m 15m S 0.0 3.8 0:19.86 httpd 9486 apache 16 0 97.7m 56m 14m S 0.0 2.9 0:13.51 httpd I have no long-running scripts (they all terminate eventually, the longest being maybe 2 minutes long), and I am working under the assumption that once each script terminates, the memory it uses gets deallocated. (Maybe someone can correct me on that). My hunch is that it could be APC, since it stores data between requests, but at the same time, it seems weird that it would store data inside the httpd process. How can I track down which part of my app is causing the memory leak? What tools can I use to see how the memory usage is growing inside the httpd process and what is contributing to it?

    Read the article

  • Googlebot repeatedly looks for files that aren't on my server

    - by John at CashCommons
    I'm hosting a site for a volunteer organization. I've moved the site to WordPress, but it wasn't always that way. I suspect at one point it was hacked badly. My Apache error log file has grown to 122 kB in just the past 18 hours. The large majority of the errors logged are of this form -- it's repeated hundreds of times today alone in my log files: [Mon Nov 12 18:29:27 2012] [error] [client xx.xxx.xx.xxx] File does not exist: /home/*******/public_html/*******.org/calendar.php [Mon Nov 12 18:29:27 2012] [error] [client xx.xxx.xx.xxx] File does not exist: /home/*******/public_html/*******.org/404.shtml (I verified that xx.xxx.xx.xxx was a Google server.) I suspect there was a security hole somewhere before, likely in calendar.php, that was exploited. The files don't exist anymore, but there may be many backlinks that exist that reference here, hence why googlebot is so interested in crawling them. How do I fix this gracefully? I still would like Google to index the site. I just want to tell it somehow not to look for these files anymore.

    Read the article

  • Instabilities with Bridged and bonded interfaces

    - by Henry-Nicolas Tourneur
    I did post yesterday to get a working setup with several bridged interfaces used for virtual machines (KVM/libvirt). One of the bridged interface is just using eth3 as its ports while the second one (public traffic) is using an ethernet bonded interface. That setup is working but not all the time ! I can start a download from a vm, then it will stop and freeze! So I don't know if my bridge parameters are correct, could you check the below config ? iface eth3 inet manual auto bond0 iface bond0 inet manual slaves eth1 eth2 pre-up ip link set bond0 up down ip link set bond0 down auto br0 iface br0 inet static address 10.160.0.7 netmask 255.255.255.128 bridge_ports eth3 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp on auto br0:1 iface br0:1 inet static address 10.160.0.9 netmask 255.255.255.255 auto br0:2 iface br0:2 inet static address 10.160.0.10 netmask 255.255.255.255 auto br1 iface br1 inet static address 217.4.40.242 netmask 255.255.255.240 gateway 217.4.40.241 pre-up /etc/network/firewall start bridge_ports bond0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp on auto br1:1 iface br1:1 inet static address 217.4.40.252 netmask 255.255.255.255 auto br1:2 iface br1:2 inet static address 217.4.40.253 netmask 255.255.255.255 And yes, it also sometimes speaks about martian on the host: kernel: [249146.055172] martian source 10.160.0.17 from 10.160.0.10, on dev vnet2 kernel: [249146.073122] ll header: ff:ff:ff:ff:ff:ff:54:52:00:76:c3:5c:08:06

    Read the article

  • NAT cause huge External (actually internal) bandwidth usage

    - by user67953
    We have 4 servers running in a data center, with internal IP: 192.168.3.* assigned. A hardware (FORTIGATE) firewall configured NAT, and it will lead the traffic as: external IP: 111.222.333.10 -> 192.168.3.10 www.server1.com 111.222.333.11 -> 192.168.3.11 www.server2.com 111.222.333.12 -> 192.168.3.12 www.server3.com In DNS, we have www.server1.com A 111.222.333.10 Now if I send a lot of data to www.server1.com from www.server2.com, the data will be send through 111.222.333.10 (external IP) and this cause our bandwidth usage huge (expensive!). The work around I have is to add a local host mapping to server2: 192.168.3.10 www.server1.com. That way when send files from server2 to www.server1.com, it will be internal. However, we are having more and more servers, it would be hard to manually add mapping to every server. Just wondering do we have another solution for this? Can we do something in the FORTIGATE firewall? ps. The DNS server being used is public, such as opendns, Google dns etc.

    Read the article

  • Apache 403 after configuring varnish

    - by w0rldart
    I just don't know where else to look and what else to do. I keep getting a 403 error on all my vhosts after setting varnish 3.0 Apacher log: [error] [client 127.0.0.1] client denied by server configuration: /etc/apache2/htdocs Headers: http://domain.com/ GET / HTTP/1.1 Host: domain.com User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:16.0) Gecko/20100101 Firefox/16.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-US,en;q=0.5 Accept-Encoding: gzip, deflate DNT: 1 Connection: keep-alive Cookie: __utma=106762181.277908140.1348005089.1354040972.1354058508.6; __utmz=106762181.1348005089.1.1.utmcsr=OTHERDOMAIN.com|utmccn=(referral)|utmcmd=referral|utmcct=/galerias/cocinas Cache-Control: max-age=0 HTTP/1.1 403 Forbidden Vary: Accept-Encoding Content-Encoding: gzip Content-Type: text/html; charset=iso-8859-1 X-Cacheable: YES Content-Length: 223 Accept-Ranges: bytes Date: Sat, 01 Dec 2012 20:35:14 GMT X-Varnish: 1030961813 1030961811 Age: 26 Via: 1.1 varnish Connection: keep-alive X-Cache: HIT ---------------------------------------------------------- /etc/default/varnish: DAEMON_OPTS="-a ip.ip.ip.ip:80 \ -T localhost:6082 \ -f /etc/varnish/main.domain.vcl \ -S /etc/varnish/secret \ -s file,/var/lib/varnish/$INSTANCE/varnish_storage.bin,1G" #-s malloc,256m" My vcl file: http://pastebin.com/axJ57kD8 So, any ideas what I could be missing? Update Just so you know, ports: NameVirtualHost *:8000 Listen 8000 and <VirtualHost 205.13.12.12:8000>

    Read the article

  • Problems installing Adobe Premiere Elements 8 Content features

    - by Walt Maken
    I recently purchased Adobe Photoshop & Premiere Elements 8. Photoshop Elements 8 installed fine, along with the additional material available via internet download. Premiere Elements 8 installed ok from the DVD. During the Premiere Elements 8 startup process the following message appears: A reduced set of content (Instant Movie Themes, Title and Menu Templates,etc) has been installed. To install the full content set, please insert your Content DVD and run Setup.exe. If you do not have a Content DVD please visit http://www.adobe.com/go/pre_additional_downloads to download the content installer. Since I didn't have the Content DVD, I did the download, which took nearly 12 hours. The extract appeared to complete at 100%, but then immediately gave the error message "A problem occurred while extracting some files. Check available space on your computer and the write privileges on the destination folder." Why would it show this error message if it had completed the extract process 100%? What step(s) do I take now to have Content installed? Do I need to go thru the 12 hour download again or, hopefully, is there something I can do that will make it unnecessary to download again?

    Read the article

  • ghc6 install trouble: hGetContents: invalid argument (invalid UTF-8 byte sequence)

    - by olimay
    Having trouble installing ghc6 on Ubuntu Maverick via apt. Here's what seems to be the relevant error that comes up when I try to (apt-get|aptitude) install ghc6: A package failed to install. Trying to recover: Setting up ghc6 (6.12.1-13ubuntu1) ... ghc-pkg: /home/opm/.ghc/i386-linux-6.12.1/package.conf.d/unix-compat-0.2-edefa7bced91ebe610d455bab466e200.conf: hGetContents: invalid argument (invalid UTF-8 byte sequence) (Here's the full output, if you're interested: http://paste.ubuntu.com/566475/ ) This still happens after apt-get clean and apt-get update. My searching around has not really helped me understand what's going on, except that it might be caused by a mismatch in locale. So, here's the output of locale too: LANG=en_US.utf8 LANGUAGE=en_US:en LC_CTYPE="en_US.utf8" LC_NUMERIC="en_US.utf8" LC_TIME="en_US.utf8" LC_COLLATE="en_US.utf8" LC_MONETARY="en_US.utf8" LC_MESSAGES="en_US.utf8" LC_PAPER="en_US.utf8" LC_NAME="en_US.utf8" LC_ADDRESS="en_US.utf8" LC_TELEPHONE="en_US.utf8" LC_MEASUREMENT="en_US.utf8" LC_IDENTIFICATION="en_US.utf8" LC_ALL= Any ideas? Additional background: this all seems very strange to me, because I used to have ghc6 installed correctly--I use XMonad as my main window manager most of the time. I tried to install haskell-platform (through apt), which failed and told me that there was something wrong with ghc6, and so I reinstalled ghc6 and began to get the above error message.

    Read the article

  • Bugzilla email issue

    - by xian
    My bugzilla system keep hit the following error: There was an error sending mail from '[email protected]' to '[email protected]':Can't send data I think that is some problem with my setting and configuration. First is the urlbase I have tried setting it to bugzilla.example.com, and http://127.0.0.1:81/, and http://10.0.0.236/ (My laptop IP address, I use this laptop to set up bugzilla) but the error still persists. Actually what should I put in the urlbase field? Parameter = Email Under mail_delivery_method, i choose SMTP. Under mailfrom, I put bugzilla-daemon. smtpserver, I tried leaving it blank, or setting it to 220.181.12.12 before, but could not solve my problem For my sql, the following is the data and command I used: C:\mysql\bin>mysql --user=root -p mysql Enter password: 1234 (When I install mysql into my laptop, it ask me to key an username and password, i have key in username as 'cvuser' and password as '1234', but here never ask me to key in any username) Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 1 Server version: 5.5.15 MySQL Community Server (GPL) mysql> GRANT ALL PRIVILEGES ON bugs.* TO 'bugs'@'localhost' IDENTIFIED BY '123456'; Query OK, 0 rows affected (0.03 sec) In C:\Bugzilla\localconfig, I put the following info: # # How to access the SQL database: # $db_host = "localhost"; # where is the database? $db_port = 3306; # which port to use $db_name = "bugs"; # name of the MySQL database $db_user = "bugs"; # user to attach to the MySQL database # # Enter your database password here. It's normally advisable to specify # a password for your bugzilla database user. # If you use apostrophe (') or a backslash (\) in your password, you'll # need to escape it by preceding it with a \ character. (\') or (\\) # $db_pass = '123456'; Can someone tell me where my mistake is? I have googled for this issue for few days but still cannot find the solution.

    Read the article

  • Using smartctl to get vendor specific Attributes from ssd drive behind a SmartArray P410 controller

    - by Lairsdragon
    Recently I have deployed some HP server with SSD's behind a SmartArray P410 controller. While not official supported from HP the server work well sofar. Now I like to get wear level info's, error statistics etc from the drive. While the SA P410 supports a passthru of the SMART Command to a single drive in the array the output I was not able to the the interesting things from the drive. In this case especially the value the Wear level indicator is from interest for me (Attr.ID 233), but this is ony present if the drive is directly attanched to a SATA Controller. smartctl on directly connected ssd: # smartctl -A /dev/sda smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 5 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 3 Spin_Up_Time 0x0000 100 000 000 Old_age Offline In_the_past 0 4 Start_Stop_Count 0x0000 100 000 000 Old_age Offline In_the_past 0 5 Reallocated_Sector_Ct 0x0002 100 100 000 Old_age Always - 0 9 Power_On_Hours 0x0002 100 100 000 Old_age Always - 8561 12 Power_Cycle_Count 0x0002 100 100 000 Old_age Always - 55 192 Power-Off_Retract_Count 0x0002 100 100 000 Old_age Always - 29 232 Unknown_Attribute 0x0003 100 100 010 Pre-fail Always - 0 233 Unknown_Attribute 0x0002 088 088 000 Old_age Always - 0 225 Load_Cycle_Count 0x0000 198 198 000 Old_age Offline - 508509 226 Load-in_Time 0x0002 255 000 000 Old_age Always In_the_past 0 227 Torq-amp_Count 0x0002 000 000 000 Old_age Always FAILING_NOW 0 228 Power-off_Retract_Count 0x0002 000 000 000 Old_age Always FAILING_NOW 0 smartctl on P410 connected ssd: # ./smartctl -A -d cciss,0 /dev/cciss/c1d0 smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net (Right, it is complety empty) smartctl on P410 connected hdd: # ./smartctl -A -d cciss,0 /dev/cciss/c0d0 smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Current Drive Temperature: 27 C Drive Trip Temperature: 68 C Vendor (Seagate) cache information Blocks sent to initiator = 1871654030 Blocks received from initiator = 1360012929 Blocks read from cache and sent to initiator = 2178203797 Number of read and write commands whose size <= segment size = 46052239 Number of read and write commands whose size > segment size = 0 Vendor (Seagate/Hitachi) factory information number of hours powered up = 3363.25 number of minutes until next internal SMART test = 12 Do I hunt here a bug, or is this a limitation of the p410 SMART cmd Passthru?

    Read the article

  • How do I repair the corrupted files found by sfc /scannow? "Windows Resource Protection found corrupt files but was unable to fix some of them."

    - by galacticninja
    After running chkdsk C: /F /R and finding out that my hard disk has 24 KB in bad sectors (log is posted below), I decided to run Windows 7's System File Checker utility (sfc /scannow). SFC showed the ff. message after I ran it: "Windows Resource Protection found corrupt files but was unable to fix some of them. Details are included in the CBS.Log windir\Logs\CBS\CBS.log." Since the CBS.log file is too large, I ran findstr /c:"[SR]" %windir%\Logs\CBS\CBS.log >"%userprofile%\Desktop\sfcdetails.txt" (as per Microsoft's KB 928228 article) to only get the log text pertaining to the corrupt files. (log is also posted below) How do I troubleshoot and repair the corrupted files mentioned by sfc /scannow? My OS is Windows 7, 64-bit. chkdsk log Checking file system on C: The type of the file system is NTFS. A disk check has been scheduled. Windows will now check the disk. CHKDSK is verifying files (stage 1 of 5)... 936192 file records processed. File verification completed. 25238 large file records processed. 0 bad file records processed. 4 EA records processed. 44 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 1051640 index entries processed. Index verification completed. 0 unindexed files scanned. 0 unindexed files recovered. CHKDSK is verifying security descriptors (stage 3 of 5)... 936192 file SDs/SIDs processed. Cleaning up 24 unused index entries from index $SII of file 0x9. Cleaning up 24 unused index entries from index $SDH of file 0x9. Cleaning up 24 unused security descriptors. Security descriptor verification completed. 57725 data files processed. CHKDSK is verifying Usn Journal... 36994248 USN bytes processed. Usn Journal verification completed. CHKDSK is verifying file data (stage 4 of 5)... 936176 files processed. File data verification completed. CHKDSK is verifying free space (stage 5 of 5)... 306238 free clusters processed. Free space verification is complete. Adding 1 bad clusters to the Bad Clusters File. Correcting errors in the Volume Bitmap. Windows has made corrections to the file system. 488282111 KB total disk space. 485595420 KB in 766458 files. 401856 KB in 57726 indexes. 24 KB in bad sectors. 1059863 KB in use by the system. 65536 KB occupied by the log file. 1224948 KB available on disk. 4096 bytes in each allocation unit. 122070527 total allocation units on disk. 306237 allocation units available on disk. Internal Info: 00 49 0e 00 81 93 0c 00 34 01 17 00 00 00 00 00 .I......4....... 6b 29 00 00 2c 00 00 00 00 00 00 00 00 00 00 00 k)..,........... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ sfc /scannow log (through findstr /c:"[SR]" %windir%\Logs\CBS\CBS.log >"%userprofile%\Desktop\sfcdetails.txt") Note: The full log is at http://pastebin.com/raw.php?i=gTEGZmWj . I've only quoted parts of the full log below (mostly from the last part), as the full log won't fit within the character limit for questions. I've added it to serve as a preview. ... 2013-12-28 19:37:50, Info CSI00000542 [SR] Beginning Verify and Repair transaction 2013-12-28 19:37:55, Info CSI00000544 [SR] Verify complete 2013-12-28 19:37:56, Info CSI00000545 [SR] Verifying 95 (0x000000000000005f) components 2013-12-28 19:37:56, Info CSI00000546 [SR] Beginning Verify and Repair transaction 2013-12-28 19:38:03, Info CSI00000548 [SR] Verify complete 2013-12-28 19:38:03, Info CSI00000549 [SR] Repairing 43 (0x000000000000002b) components 2013-12-28 19:38:03, Info CSI0000054a [SR] Beginning Verify and Repair transaction ... 2013-12-28 19:38:15, Info CSI00000730 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:62{31}]"GroupPolicy-Admin-Gpedit-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000733 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:30{15}]"frs-core-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000736 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:26{13}]"gpmgmt-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000739 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:74{37}]"MediaServer-ASPAdmin-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000073c [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:36{18}]"Ldap-Client-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000073f [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:38{19}]"iSNS_Service-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000742 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:76{38}]"MediaServer-Multicast-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000745 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:78{39}]"Kerberos-Key-Distribution-Center-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000748 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:86{43}]"GroupPolicy-CSE-SoftwareInstallation-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000074b [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:28{14}]"ieframe-dl.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000074e [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:76{38}]"GroupPolicy-Admin-Gpedit-Snapin-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000751 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:32{16}]"IPSec-Svc-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000754 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:22{11}]"HTTP-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000757 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:56{28}]"MediaServer-Migration-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000075a [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:26{13}]"GPBase-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI0000075d [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:38{19}]"IasMigPlugin-DL.man"; source file in store is also corrupted 2013-12-28 19:38:15, Info CSI00000760 [SR] Could not reproject corrupted file [ml:520{260},l:84{42}]"\??\C:\Windows\System32\migwiz\dlmanifests"\[l:50{25}]"International-Core-DL.man"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000762 [SR] Cannot repair member file [l:24{12}]"wbemdisp.dll" of Microsoft-Windows-WMI-Scripting, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000763 [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI00000766 [SR] Could not reproject corrupted file [ml:58{29},l:56{28}]"\??\C:\Windows\SysWOW64\wbem"\[l:24{12}]"wbemdisp.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000768 [SR] Cannot repair member file [l:56{28}]"Microsoft.MediaCenter.UI.dll" of Microsoft.MediaCenter.UI, Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_MSIL (8), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000769 [SR] This component was referenced by [l:176{88}]"Microsoft-Windows-MediaCenter-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.MediaCenter" 2013-12-28 19:38:16, Info CSI0000076c [SR] Could not reproject corrupted file [ml:520{260},l:40{20}]"\??\C:\Windows\ehome"\[l:56{28}]"Microsoft.MediaCenter.UI.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI0000076e [SR] Cannot repair member file [l:24{12}]"ReAgentc.exe" of Microsoft-Windows-WinRE-RecoveryTools, Version = 6.1.7601.17514, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI0000076f [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI00000772 [SR] Could not reproject corrupted file [ml:48{24},l:46{23}]"\??\C:\Windows\SysWOW64"\[l:24{12}]"ReAgentc.exe"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000774 [SR] Cannot repair member file [l:82{41}]"System.Management.Automation.dll-Help.xml" of Microsoft-Windows-PowerShell-PreLoc.Resources, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_AMD64 (9), Culture = [l:10{5}]"en-US", VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI00000775 [SR] This component was referenced by [l:266{133}]"Microsoft-Windows-Client-Features-Package~31bf3856ad364e35~amd64~en-US~6.1.7601.17514.Microsoft-Windows-Client-Features-Language-Pack" 2013-12-28 19:38:16, Info CSI00000778 [SR] Could not reproject corrupted file [ml:520{260},l:104{52}]"\??\C:\Windows\System32\WindowsPowerShell\v1.0\en-US"\[l:82{41}]"System.Management.Automation.dll-Help.xml"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI0000077a [SR] Cannot repair member file [l:18{9}]"hlink.dll" of Microsoft-Windows-HLink, Version = 6.1.7600.16385, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral in the store, hash mismatch 2013-12-28 19:38:16, Info CSI0000077b [SR] This component was referenced by [l:202{101}]"Microsoft-Windows-Foundation-Package~31bf3856ad364e35~amd64~~6.1.7601.17514.WindowsFoundationDelivery" 2013-12-28 19:38:16, Info CSI0000077e [SR] Could not reproject corrupted file [ml:48{24},l:46{23}]"\??\C:\Windows\SysWOW64"\[l:18{9}]"hlink.dll"; source file in store is also corrupted 2013-12-28 19:38:16, Info CSI00000780 [SR] Repair complete 2013-12-28 19:38:16, Info CSI00000781 [SR] Committing transaction 2013-12-28 19:38:19, Info CSI00000785 [SR] Verify and Repair Transaction completed. All files and registry keys listed in this transaction have been successfully repaired

    Read the article

  • How to prioritize openvpn traffic?

    - by aditsu
    I have an openvpn server, with one network interface. VPN traffic is extremely slow. I tried to do traffic control with this configuration (currently): qdisc del dev eth0 root qdisc add dev eth0 root handle 1: htb default 12 class add dev eth0 parent 1: classid 1:1 htb rate 900mbit #vpn class add dev eth0 parent 1:1 classid 1:10 htb rate 1500kbit ceil 3000kbit prio 1 #local net class add dev eth0 parent 1:1 classid 1:11 htb rate 10mbit ceil 900mbit prio 2 #other class add dev eth0 parent 1:1 classid 1:12 htb rate 500kbit ceil 1000kbit prio 2 filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip sport 1194 0xffff flowid 1:10 filter add dev eth0 protocol ip parent 1:0 prio 2 u32 match ip dst 192.168.10.0/24 flowid 1:11 qdisc add dev eth0 parent 1:10 handle 10: sfq perturb 10 qdisc add dev eth0 parent 1:11 handle 11: sfq perturb 10 qdisc add dev eth0 parent 1:12 handle 12: sfq perturb 10 But it's still extremely slow. I have an imaps connection that keeps transferring data continuously (I successfully limited the rate) but with openvpn I can't seem to get more than about 100kbit/s The internet connection speed is about 3mbit/s (symmetric) What could be the problem? Does the sport filter work for udp?

    Read the article

  • Connection reset by peer: mod_fcgid: error reading data from FastCGI server Issues

    - by user145857
    Help is greatly needed for our server. We are experiencing random "Connection reset by peer: mod_fcgid: error reading data from FastCGI server" errors which cause a 500 internal server error. If the page is then reloaded it loads normally as it should. We are running MPM Worker with mod FCGID to handle PHP. We had APC cache enabled but disabled it recently to see if it would fix the problem, but the random mod FCGID errors are still continuing. No other opcode cache is active now. Our settings are below: <IfModule worker.c> MinSpareThreads 25 MaxSpareThreads 150 ThreadsPerChild 25 ThreadLimit 100 ServerLimit 700 MaxClients 700 MaxRequestsPerChild 0 </IfModule> <IfModule mod_fcgid.c> FcgidMaxRequestLen 1073741824 FcgidMaxRequestsPerProcess 2000 FcgidMaxProcessesPerClass 100 FcgidMinProcessesPerClass 0 FcgidConnectTimeout 300 FcgidIOTimeout 900 FcgidFixPathinfo 1 FcgidIdleTimeout 300 FcgidIdleScanInterval 120 FcgidBusyTimeout 300 FcgidBusyScanInterval 120 FcgidErrorScanInterval 12 FcgidZombieScanInterval 12 FcgidProcessLifeTime 3600 </IfModule> The server is a 64 core 2.1 GHZ 94 GB RAM so it has some power. Some of the fcgid timeout settings are higher because we run large reports which take up to 15 minutes. Any help is greatly appreciated! Just to clarify, the random fcgid errors are occurring when a user clicks a page on our site and the 500 error page loads instantly. This is random and occurrs less than 1% of the time but it is still an issue.

    Read the article

  • RabbitMQ message consumers stop consuming messages

    - by Bruno Thomas
    Hi server fault, Our team is in a spike sprint to choose between ActiveMQ or RabbitMQ. We made 2 little producer/consumer spikes sending an object message with an array of 16 strings, a timestamp, and 2 integers. The spikes are ok on our devs machines (messages are well consumed). Then came the benchs. We first noticed that somtimes, on our machines, when we were sending a lot of messages the consumer was sometimes hanging. It was there, but the messsages were accumulating in the queue. When we went on the bench plateform : cluster of 2 rabbitmq machines 4 cores/3.2Ghz, 4Gb RAM, load balanced by a VIP one to 6 consumers running on the rabbitmq machines, saving the messages in a mysql DB (same type of machine for the DB) 12 producers running on 12 AS machines (tomcat), attacked with jmeter running on another machine. The load is about 600 to 700 http request per second, on the servlets that produces the same load of RabbitMQ messages. We noticed that sometimes, consumers hang (well, they are not blocked, but they dont consume messages anymore). We can see that because each consumer save around 100 msg/sec in database, so when one is stopping consumming, the overall messages saved per seconds in DB fall down with the same ratio (if let say 3 consumers stop, we fall around 600 msg/sec to 300 msg/sec). During that time, the producers are ok, and still produce at the jmeter rate (around 600 msg/sec). The messages are in the queues and taken by the consumers still "alive". We load all the servlets with the producers first, then launch all the consumers one by one, checking if the connexions are ok, then run jmeter. We are sending messages to one direct exchange. All consumers are listening to one persistent queue bounded to the exchange. That point is major for our choice. Have you seen this with rabbitmq, do you have an idea of what is going on ? Thank you for your answers.

    Read the article

  • Resolving a BSOD/CPU/GPU issue...

    - by Christian Sciberras
    Hello all, I'm getting a BSOD / system crash (sometimes the PC just quits without a BSOD). Hardware Specifications cpu: i7 920 2666MHz / 8 cores (not OCed afaik) mobo: Asus P6T SE ram: 2x Corsair CM3X2G1333C9 (64bit DDR3 667MHz) gfx: ATI Radeon HD 5970 1GB (XFX HD5970 BE) os: Windows 7 Ultimate 64 bit (legit) All bios, firmware and drivers are all up to date (as of today). Symptoms Sometimes the PC runs smoothly, sometimes I get this BSOD. The BSOD always happens when I'm doing something related to graphics, such as viewing a video or playing a game. I get to know about the imminent BSOD ~10 seconds earlier; the PC starts freezing occasionally but increasing in frequency and length of lag (I noticed processor usage in creased from Process Monitor). I've tweaked BIOS settings occasionally but afaik, it was in vain. A day or so ago, I reset it to factory settings. BSOD contents The computer has rebooted from a bugcheck. The bugcheck was: 0x00000101 (0x0000000000000019, 0x0000000000000000, 0xfffff88001f35180, 0x0000000000000004). 15-12-2010 A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Internal Timer Error Processor ID: 4 23-12-2010 A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Internal Timer Error Processor ID: 2 Important The interesting thing is that although the event log (and BSOD screen) blame a "secondary processor", Windows Action Center sometimes blamed the GFX driver (for the same error). Also It is interesting to note that after hibernating my PC, I always get the BSOD.

    Read the article

  • Re-sizing disk partition linux/vm

    - by Tiffany Walker
    I VM Player running a linux guest and I was wanting to know how do I expand the disk? In the VM player I gave more disk space but I am not sure how to mount/expand/connect the new disk space to the system. My old disk space was 14GB [root@localhost ~]# df -h / Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup-lv_root 14G 4.5G 8.2G 36% / Then I expanded it and now I see sda2 which is the new space? [root@localhost ~]# fdisk -l Disk /dev/sda: 128.8 GB, 128849018880 bytes 255 heads, 63 sectors/track, 15665 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000cd44d Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 2611 20458496 8e Linux LVM Disk /dev/mapper/VolGroup-lv_root: 14.5 GB, 14537457664 bytes 255 heads, 63 sectors/track, 1767 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/VolGroup-lv_swap: 6408 MB, 6408896512 bytes 255 heads, 63 sectors/track, 779 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Do I need to mount the new space first? resize2fs -p /dev/mapper/VolGroup-lv_root 108849018880 resize2fs 1.41.12 (17-May-2010) The containing partition (or device) is only 3549184 (4k) blocks. You requested a new size of 1474836480 blocks. resize2fs -p /dev/mapper/VolGroup-lv_root 128849018880 resize2fs 1.41.12 (17-May-2010) resize2fs: Invalid new size: 128849018880 [root@localhost ~]# lvextend -L+90GB /dev/mapper/VolGroup-lv_root Extending logical volume lv_root to 103.54 GiB Insufficient free space: 23040 extents needed, but only 0 available [root@localhost ~]# lvextend -L90GB /dev/mapper/VolGroup-lv_root Extending logical volume lv_root to 90.00 GiB Insufficient free space: 19574 extents needed, but only 0 available EDIT: So after trying pvcreate/vgextend nothing has so far worked. I'm guessing the new disk space added from VM Player is not showing up? pvscan PV /dev/sda2 VG VolGroup lvm2 [19.51 GiB / 0 free] Total: 1 [19.51 GiB] / in use: 1 [19.51 GiB] / in no VG: 0 [0 ]

    Read the article

  • How do I compile DarWINE in PowerPC Mac OS X 10.4.11...?

    - by Craig W. Davis
    So far I've tried using MacPorts which gives me this error: /Error: Cannot install wine for the arch(s) 'powerpc' because Error: its dependency pkgconfig is only installed for the archs 'i386 ppc'. Error: Unable to execute port: architecture mismatch To report a bug, etc... (I'm not allowed to post two links due to being a new poster...)./ I've also tried using the build script I found in the DarWINE 0.9.12 SDK download that I found on the DarWINE SourceForge.net Project Page... I've also tried the build script that I found at http://code.google.com/p/osxwinebuilder/#Building_Wine_via_the_script... None of these attempts to build DarWINE have actually worked. Whenever I build using the DarWINE build script I run it as follows: /1. I decompress the WINE tarball into ~/Downloads/WINE 2. I cd into ~/Downloads/DarWINE. 3. I run ./winemaker ~/Downloads/WINE/wine-1.2.2 or ./winemaker ~/Downloads/WINE/wine-1.2-rc2 (the reason for trying WINE 1.2-rc2 is that some people managed to get it to build on PowerPC Macs running 10.5.8...)./ I made sure to install Xcode Tools 2.5 & all the SDKs too... The net result is either a syntax type error resulting from trying to run the checked out Google Code DarWINE build script or a bunch of make errors when trying to run the official DarWINE build script that I forcefully extracted from the DarWINE 0.9.12 SDK .dmg file by using Pacifist. I trying to build DarWINE on mid-April 2006 1.42 GHz eMac with DL SuperDrive with Bluetooth 2.0+EDR with 2 GBs of RAM running 10.4.11 as I mentioned earlier... (it came with 10.4.4 on the Mac's Restore DVD-ROM that I ordered from 1-800-SOS-APPL & coconutIdentityCard told me it was made on April 12th 2006 & I know that's right because when I reinstalled Mac OS X 10.4.4 it displayed that it was registered/previously owned by a Hawaiian school...): /make[1]: winegcc: Command not found make[1]: * [main.o] Error 127 make: * [dlls/acledit] Error 2./

    Read the article

  • Postfix a lot of relay acces denied errors in maillog

    - by tester3
    I'm on Centos 6.5 with Postfix/Dovecot and some virtual domains. Postfix works fine, but I've got a lot of messages like this "NOQUEUE: reject: RCPT from 1-160-127-12.dynamic.hinet.net[1.160.127.12]: 454 4.7.1 : Relay access denied; from= to= proto=SMTP" in my maillog. I've tried to close port 25 with iptables, when I do so - I got no such messages, but my mail system starts work incorrectly and can't receive mail from other hosts. Please help! My postconf -n: alias_database = $alias_maps alias_maps = hash:/etc/postfix/aliases broken_sasl_auth_clients = yes command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 html_directory = no inet_interfaces = all inet_protocols = ipv4 mail_owner = postfix mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man message_size_limit = 20971520 mydestination = localhost.$mydomain, localhost newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES relay_domains = * sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtp_tls_cert_file = /etc/pki/tls/certs/example.com.crt smtp_tls_key_file = /etc/pki/tls/private/example.com.key smtp_tls_loglevel = 1 smtp_tls_session_cache_database = btree:/etc/postfix/smtp_tls_session_cache smtp_tls_session_cache_timeout = 3600s smtp_use_tls = yes smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_local_domain = example.com smtpd_sasl_path = /var/run/dovecot/auth-client smtpd_sasl_security_options = noanonymous smtpd_sasl_tls_security_options = $smtpd_sasl_security_options smtpd_sasl_type = dovecot smtpd_tls_cert_file = /etc/pki/tls/certs/example.com.crt smtpd_tls_key_file = /etc/pki/tls/private/example.com.key smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_session_cache_database = btree:/etc/postfix/smtpd_tls_session_cache smtpd_tls_session_cache_timeout = 3600s smtpd_use_tls = yes soft_bounce = yes tls_random_source = dev:/dev/urandom unknown_local_recipient_reject_code = 550 virtual_alias_maps = hash:/etc/postfix/vmail_aliases virtual_gid_maps = static:2222 virtual_mailbox_base = /var/vmail virtual_mailbox_domains = hash:/etc/postfix/vmail_domains virtual_mailbox_maps = hash:/etc/postfix/vmail_mailbox virtual_minimum_uid = 2222 virtual_transport = virtual virtual_uid_maps = static:2222 Please help! Will attach master.cf or anything other if needed.

    Read the article

< Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >