Search Results

Search found 5322 results on 213 pages for 'answers'.

Page 153/213 | < Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >

• Add IPv6 support to DirectAdmin server

  - by George Boot

  I just set up an new DirectAdmin, and I want to prepare it for IPv6 use. My ISP have gave me an range of IPv6 addresses that I can use. Lets say that address is 2a01:7c8:**:1f::. My neworkadapter user DHCP to resolves its IP-addresses. When i type ifoncig eth0 I get the following result: eth0 Link encap:Ethernet HWaddr 52:**:**:**:ce:f3 inet addr:37.**.**.44 Bcast:37.**.**.255 Mask:255.255.255.0 inet6 addr: 2a01:7c8:****:1f::/64 Scope:Global inet6 addr: fe80::5054:ff:fe87:cef3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38941 errors:0 dropped:0 overruns:0 frame:0 TX packets:29439 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3779534 (3.6 MiB) TX bytes:5089379 (4.8 MiB) As you can see, I have an IPv6 address set, but I can't ping6 an IPv6 host. I get the error: connect: Network is unreachable. I decided that I needed an gateway, so I tryed to add one: ip -6 route add default via 2a01:7c8:****::1 dev eth0 (2a01:7c8:**::1 is the gateway of my ISP). But it trows an error: RTNETLINK answers: No route to host. Does somebody know what to do, and how to solve this issue? Thanks a lot!

  Read the article

• Why does the screen resolution of 1440x900 suddenly disappear from Intel GMA Control Panel?

  - by GeneQ

  I'm using a Vostro 1200 laptop with the Mobile Intel(R) 965 Express Chipset powering its graphics and running Vista 32-bit SP2. I've been using the Vostro with a Dell SE198WFP LCD Monitor as the external display since day one for about two years without any problems. Recently, I plugged the Vostro into a couple of other monitors. The problem is, now the native resolution for my main monitor's (the SE198WFP) resolution of 1440x900 @ 60 Hz is no longer available. (See below) I've tried everything from uninstalling and reinstalling the Intel drivers as well as the monitor drivers to no avail. I've goggled this problem and it appears that this has happened to other people but all the answers involve people giving up in frustration or reinstalling; both terrible outcomes. Has anybody ever figured why this happens and have a good solution? UPDATE: This dude has a complicated solution, which I haven't tried yet. His explanations for the problem was After an exausting search for an answer to the matter of why my brand new 19? widescreen monitor’s native resolution (1440×900) was unavailible (sic) in the display properties, I finally stumbled upon an article a person posted on Intel’s forums that basically explained what shannanigans Intel had been up to with their GMA 950 line of onboard graphic solutions. Not very comforting.

  Read the article

• Official end of support date for Internet Explorer 6 on Windows XP

  - by scunliffe

  If I read the docs on Windows Service Pack support policies, and the specific Internet Explorer lifecycle support page as well as the Wikipedia page I've deduced that: IE6 support ends/ended at: Windows 2000 Ended (date unknown) Windows XP SP0 (RTM) Ended Home: 30-Aug-2003 Pro: 30-Sep-2004 SP1 Ended Home: 11-Jul-2004 Pro: 11-Jul-2004 SP2 Home: 13-Jul-2010 Pro: 13-Jul-2010 SP3 (released: April 21, 2008) Home: ??? Pro: ??? What isn't clear is the Windows XP SP3 scenario. In "human" terms, when is the end of support for IE6 on Windows XP SP3? e.g. if there is never a Windows XP SP4... or heaven forbid, an SP4 is released. I realize this doesn't force people to upgrade etc. however I'm trying to get a "semi" official word on when IE6 moves into the "not supported" category. I'm not interested in philosophical answers e.g. "big enterprise won't upgrade but they will expect support into 2017" stuff... I just want the "clear answer" in terms of official Microsoft support.

  Read the article

• Apache, httpd process 4MB+ memory use, Wordpress, Dedicated Server

  - by david

  What is happening to apache? I cannot trace down the processes doing this to my server. I can't anymore, the server is crashing every day a few times. Don't know what to do anymore, tried all the answers here, i can't find the problem. apache 5978 0.0 1.4 34060 14000 ? S 10:13 0:00 /usr/sbin/httpd apache 5979 1.8 3.6 61660 35632 ? S 10:13 0:02 /usr/sbin/httpd apache 5982 1.9 3.6 61712 35640 ? S 10:13 0:02 /usr/sbin/httpd apache 5983 0.0 1.7 46000 17480 ? S 10:13 0:00 /usr/sbin/httpd apache 5984 1.4 4.3 70880 42644 ? S 10:13 0:02 /usr/sbin/httpd apache 5985 2.6 4.3 69864 42888 ? S 10:13 0:04 /usr/sbin/httpd apache 5986 0.7 3.9 67240 39220 ? S 10:13 0:01 /usr/sbin/httpd apache 5987 0.8 3.9 67240 39228 ? S 10:13 0:01 /usr/sbin/httpd apache 5988 2.5 4.3 70136 43160 ? S 10:13 0:03 /usr/sbin/httpd apache 6151 0.0 1.7 45868 17404 ? S 10:15 0:00 /usr/sbin/httpd

  Read the article

• Windows 7 x64 wired connection problem. IP, gateway, dns assigned, can't ping. Network detected as "Network"

  - by Emil Lerch

  I am having a problem connecting to a specific wired network with my Latitude E6410 laptop. Other wired networks seem to work fine, but this one does not. I have a coworker with me with the same Intel 82577LM Gigabit Network card, and he can connect just fine. I've updated to the latest Intel drivers (11.8.75.0) and am not using Pro Set. I obtain all DHCP information just fine (IP, netmask, DNS server, default gateway). I cannot ping anything (internal or on the Internet - I tried pinging Google's public DNS servers by IP 8.8.8.8), nor can I get answers to any DNS queries through NS Lookup. Windows troubleshooting says everything is fine, but I can't get DNS responses. I've seen issues like this in the past that were related to link speed/duplex autonegotiaion failures, so I've tried manually setting link speed/duplex to all values one by one with no success. My coworker is using all default settings, so he is just using autonegotiate. Any ideas of other things to try?

  Read the article

• Using 1and1.com Servers, SMTP Mail is Limited - Local XAMPP Server Works As Expected

  - by nicorellius

  I'm starting to not like 1and1.com that much. I've used them for years, but mainly for simple sites without much need for configuration. I know there are better hosting companies out and I may go seeking them. The problem here is that on my Local XAMPP server (sitting on a network with Comcast ISP), I have a PHP script that uses PEAR::Mail to send mail using MIME. The script works find locally with either smtp.1and1.com and corresponding credentials and smtp.gmail.com with corresponding credentials, using appropriate ports, etc. 1and1 tells me that I have to change the MX record on the domain where this script runs in order to make this work. This doesn't make sense to me. Now I'm pretty new to all this, but how is it that this is the case? Why can my local server work just fine, out of the box, but their servers not? I have asked them these questions, but they are very vague and I cannot get any good answers from them. Versions: PEAR Version: 1.5.0 PHP Version: 4.4.9 Zend Engine Version: 1.3.0 My apologies in advance for my ignorance. Thanks for the help in advance.

  Read the article

• Campus VLAN Segmentation - By OS?

  - by Moduspwnens

  We've been thinking through re-arranging our network and VLAN configuration. Here's the situation. We already have our servers, VoIP phones, and printers on their own VLANs, but our problem lies with end user devices. There are just too many to lump on the same VLAN without being hammered with broadcasts! Our current segmentation strategy has them split into VLANs like this: Student iPads Staff iPads Student Macbooks Staff Macbooks Gaming devices Staff (Other) Student (Other) *Note that our network has many more iPads and MacBooks than most. Since the primary reason we're splitting them is just to put them in smaller groups, this has been working for us (for the most part). However, this required our staff to maintain access control lists (MAC addresses) of all devices belonging in these groups. It also has the unfortunate side effect of illogically grouping broadcast traffic. For example, using this setup, students on opposite ends of campus using iPads will share broadcasts, but two devices belonging to the same user (in the same room) will likely be on completely separate VLANs. I feel like there must be a better way of doing this. I've done a lot of research and I'm having trouble finding instances of this kind of segmentation being recommended. The feedback on the most relevant SO question seems to point toward VLAN segmentation by building/physical location. I feel like that makes sense because logically, at least among miscellaneous end users, broadcasts will typically be intended for nearby devices. Are there other campuses/large-scale networks out there segmenting VLANs based on end-system OS? Is this a typical configuration? Would VLAN segmentation based on physical location (or some other criteria) be more effective? EDIT: I've been told that we will soon be able to dynamically determine device OS without maintaining access lists, although I'm not sure how much that affects the answers to the questions.

  Read the article

• How to point a subdomain to local server with dynamic IP

  - by jlego

  I see there are many related questions to this one, however the answers given seem to be a little vague for a novice like me. I've got a dedicated LAMP stack running Fedora 16 locally on my home network. Everything works fine internally. I can access the Apache server from other machines on the network using the internal IP in a browser. I'm using the stack for a local file server as well as a development environment for websites. There are a couple of reasons why I would like the development sites hosted on the machine to be available publicly. 1.) I use a CMS that has paid add-ons which allows you to assign the paid license to a domain. I can't develop with paid add-ons on the closed dev server. 2.) I would occasionally like for clients to be able to view the site dev at late stages before it goes live. I have a domain (foo.com, and I want to point a *sub*domain (dev.foo.com) to the local server. I know this is best accomplished with a Static IP, however my IP from my ISP is Dynamic and I don't think there is any way to change that. From what I have read, services like ZoneEdit & DynDNS are supposed to be able to accomplish this, but I have tried both and found it very confusing. Also the server is behind a router and I have also read that you need to set up DDNS(?) in your router, that many routers have presets for these services, and I've found that DynDNS is the only one my router seems to support.

  Read the article

• Apache crashes every 5min

  - by Simon

  I'm relatively new to server issues, having a site of mine that I started early in the year grow beyond my capabilities of managing it. I need help. I recently moved out of my shared hosting environment onto a dedicated virtual server from Mediatemple. Each week, I run a script that fetches data from my DB, fetches data from last.fm's API and then tweets information to Twitter. My server uses Virtuozzo and when the script runs, Apache crashes every 5min. I checked and saw that the 'kmemsize' parameter reaches its cap (its 13mb). I realise my problem. The MySQL process stays open for long while Apache needs to handle lots of incoming links (about 200 000 pageviews for that day according to my previous host's AWSTATS). Yes, I'm quite unexperienced in this, and I'm clearly killing the server with too many incoming links while it has to manage the updating of the DB. So that is the precedent: I want a few answers. 1) Why did my shared hosting environment not crash apache every 5min? It ran fine, the site only slowed a lot. Clearly, it must be the virtual container and the kmemsize limit? 2) Where do I go from here? Would a physical server (not a virtual container) encounter the same problems? I sent a support request to Mediatemple as well. I need all the help I can get.

  Read the article

• How to crop Screen Recordings under Snow Leopard?

  - by willc2

  Quicktime Player for Snow Leopard now allows you record the screen. Awesome! Once you have a movie it will let you trim screen recordings for length. Is there a way to crop the movie's dimensions, either in QT or using some built-in or free software? Update: How to crop to an arbitrary size and aspect ratio? iMovie only seems to let you crop to the aspect ratio of the containing project. Result: Both good answers but since I have QuickTime Player 7 and Photoshop, that's the workflow I choose as the answer. NOTE: If you have Photoshop Extended, you can import a movie, use the crop tool, and Export the cropped movie. Not free or built-in, but convenient. To summarize the instructions from the video link ricbax posted: Open movie in QuickTime Player 7 Copy a frame and Paste it into a new document in Photoshop Draw a rectangular selection around the area to keep and fill with black Invert the selection and fill with white Save as .GIF, with 2 colors Back in QuickTime Player 7, open Movie Properties window Select the Video Track Select the Visual Settings Tab Drag and Drop the 2-color .GIF file onto the Mask drop area (or use choose file button) Export the (now cropped) movie DONE

  Read the article

• Reducing video mode switching during Linux boot

  - by Zack

  When I boot up my desktop computer, which only has Linux on it, the video mode and/or console font gets switched four times: When GRUB starts, it switches from 80x25 text to a graphical mode so it can draw a pretty background behind its menu; GRUB then goes back to 80x25 text after I pick something from the menu; When the KMS driver for my video card loads, it switches to a much higher-resolution text mode (I don't know if this is a hardware text mode or not); Finally X starts and it goes graphics and stays that way. I think this last switch does not change the resolution of the video mode, only the graphicalness. I'd like to get rid of as many of these mode switches as possible. Ideally, when GRUB takes over from the BIOS it would go directly to the same high-resolution text mode that the KMS driver selects, and the display would stay in that mode till X starts and brings up graphics. I am under the impression that this is possible by mucking with the kernel command line and/or the GRUB console module load parameters, but I don't know the details. GRUB 1.98+20100706, kernel 2.6.32.15 using Nouveau video drivers. Distro is Debian unstable. Please no answers that involve recompiling anything or cobbling together bleeding-edge kernel/driver combinations, I don't care enough about this to go to that much trouble. EDIT: Tobu suggests setting GRUB_GFXMODE to the full pixel resolution of the monitor, and GRUB_GFXPAYLOAD_LINUX=keep to avoid the mode switch after the menu goes away. This does part of what I want, but winds up being worse overall. There's no mode switch after the menu, but there's still a painfully-slow screen repaint (I should probably just give up on GRUB's gfxmode, it's waaaay too slow at 1920x1200). More seriously, there's now a double mode switch when nouveaufb loads, along with fun-looking error messages in dmesg [ 5.923798] [drm] nouveau 0000:02:00.0: allocated 1920x1200 fb: 0x40250000, bo ffff8801ba5f4600 [ 5.923802] fb: conflicting fb hw usage nouveaufb vs EFI VGA - removing generic driver [ 5.923821] [drm] nouveau 0000:02:00.0: PFIFO_INTR 0x00000010 - Ch 1 ("PFIFO_INTR" message repeats 400+ times) [ 5.925609] Console: switching to colour dummy device 80x25 [ 5.925802] Console: switching to colour frame buffer device 240x75

  Read the article

• Setup 2003 R2 Radius server to work on vista/seven

  - by Fox

  Hi All, I'm currently trying to configure my 2003 R2 server RADIUS module to enable WIFI client to authenticate throught my Active Directory. The RADIUS server use MS-CHAP V2 as encryption method. I got several Access Point running DD-WRT, configured to use WPA2-Enterprise security that use Radius Server. Everything is setup, and almost working. When I say almost working, I mean, I can login using my AD Credential on my IPod or even on a MacBook running OS X, Windows XP also work with some little tweak in connection properties. The problem is Windows Vista or Windows Seven clients computers that are not inside domain. It doesn't work at all, it doesn't even prompt for user/password/domain. I already install the patch for IAS to make the certsrv compatible with Vista and Seven, but still doesn't work. Anyone ever encounter the same issue I have right now? I'm searching for a solution to this for several already and still not find anything. Looks like many people have the same issue too. Thanks all for you eventual answers.

  Read the article

• The Server Fault Wiki of recommended practices [migrated]

  - by Avery Payne

  So I've noticed that there are several recommendations on basic practices on Server Fault, but there doesn't seem to be a cohesive view as to how those recommendations would all fit together. So I thought I would lump these together as a kind of mental exercise to see what the "ServerFault Community IT Department" would look like if it were implemented. This would give a few things: it would make a reasonable wiki (in the true wiki spirit of many contributions), it would provide several links to well-vetted practices, and it would be kind of fun to see what the amalgamation would look like. And who knows, it may even point out some interesting issues between different forms of "best practices", although I would be stunned if there was a conflict hidden in there someplace... Add your favorites from Server Fault as answers, and I'll re-edit this section with the results. Here's a few catagories to collect different ideas together. Hardware Configuration(s) Server room configuration. Server room temperature Firmware Updates and Scheduling Storage Configuration(s) Selecting a NAS box Linux: Dealing with /tmp Linux: Install apps in /var or /opt? Network Configuration(s) checking DNS health and compliance Security Practice(s) Password (General) Best Practices Password sharing methods Windows Update Updating Windows Servers that are hosts for VMs Network Service(s) User Service(s) User Naming & Deletion Upgrade Process(es) Disaster Recovery Checking Backups Documenting an outage for a post-mortem review Last Edit: 2010-02-17

  Read the article

• Workstations cannot see new MS Server 2008 domain, but can access DHCP. (solved)

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• internet-based sync software that will keep running after Windows Live Sync stops doing PC-to-PC-syncs?

  - by Warren P

  According to the wikipedia page, Microsoft Live Sync will shortly stop offering the PC-to-PC sync service. There are lots of apps to sync two PCs on the same LAN, but I want to sync two PCs that are in different cities, across the internet, traversing two different NATs, and that requires some kind of service running in the internet that both connect into. There is already a few questions about syncing folders and files, but this is not a duplicate because none of them answer this basic question: Microsoft Live Sync works better than RSYNC, or any of the linked SYNC solutions in any of the "not really duplicates" because it works even when the two PCs have NAT and firewalls between them that forbid direct connectivity, because Windows Live Sync has a free always-on internet server that all the client PCs connect into. I'm looking for a FREE (no-fees) Microsoft Live Sync work-alike PC-to-PC sync solution that works between PCs and Macs, at least, as well as between PCs, and works behind NAT and firewalls at least as well as Microsoft's solution. (Note that Microsoft's solution makes only outbound socket calls to a microsoft server, so this solution must necessarily include a server-hub component that is hosted publically on a free site and which does not require that I set up and manage and pay for my own public internet hosting site) Hint: None of the answers in the linked duplicate are equivalent (PureSync,FreeFileSync,BestSync 2010,SyncButler,Comodo BackUp,QuickShadow,Gbridge) in that none of them work for the PC to Mac situation, where firewalls and nats prevent direct connection, or else they require money to be paid. When Microsoft Live Sync / Live Mesh finally kills direct PC-to-PC mode, the limitation will be that you will have to pay for more than 25 GB of cloud service, and you can then only sync PC #1 to PC #2 if you first sync to the cloud, then down to other clients. I can currently sync 100 gb of data from one computer to another, only temporarily "moving the data" through Microsoft's data servers without using up my Skydrive storage quota.

  Read the article

• Update Grub on Squeeze - Kernel downgrade due VMware Server

  - by vodoo_boot

  Hi! I happen to run into various problems regarding grub and kernels. I don't really care about the kernel internas. All I want is VMware server in that dedicated root-server. 1.) What is a bzImage vs. vmlinuz? kaze:~# ls /boot/ System.map-2.6.32-5-amd64 bzImage-2.6.33.2 config-2.6.33.2 initrd.img-2.6.32-5-amd64 System.map-2.6.33.2 bzImage-2.6.35.6 config-2.6.35.6 vmlinuz-2.6.32-5-amd64 System.map-2.6.35.6 config-2.6.32-5-amd64 grub I updated my menu.lst (grub2): timeout 5 default 0 fallback 1 title 2.6.32.5 kernel (hd0,1)/boot/vmlinuz-2.6.32-5-amd64 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.35.6 kernel (hd0,1)/boot//bzImage-2.6.35.6 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.32.3 kernel (hd0,1)/boot//bzImage-2.6.33.2 root=/dev/sda2 panic=60 noapic acpi=off That doesn't do well... I think the vmlinuz file is missing initrd or so. Dunno. In fact I don't give too much about kernel boot voodoo as long as it works. update-grub(2) does not work. Does anybody know what magical trick there is to get the 2.6.32-5 booting? 2.) I thought t follow the Deban wiki.. I cannot get header-files for the installed 35.6 or 33.2 kernel in the repositories. I cannot build foreign headers because they will not match the running kernel. So how does one deal with that situtation? I'd prefer not to have to downgrade the kernel. Thanks for any answers!

  Read the article

• Vanishing Windows Desktop Shortcut Keys

  - by Henry Keiter

  The Situation Like you, I have many applications that I like to open. I've set up keyboard shortcuts for the most common, by placing a link on the desktop and setting its Shortcut Key property: This is all fine and dandy, most of the time. When I want to bring up the GIMP, I press Ctrl+Alt+G and the GIMP launches. Lovely. The Problem Sometimes--perhaps once a month per desktop shortcut--the shortcut key assignment simply vanishes. I press Ctrl+Alt+G and nothing happens, so I go check the shortcut and see that lo and behold: nothing is there. This happens regularly to all my shortcuts (not all at once). It doesn't matter what keys I assign, and there doesn't seem to be any correlation with particular applications being open or anything of that sort. This has happened on every Windows XP machine I've ever used with any regularity. Obviously what makes this issue particularly obnoxious is that it's not easily reproducible. I have searched long and hard for a solution for (or at least acknowledgement of) this problem, to no avail, so hopefully you guys know something that I don't. I did find this question, where the answers are all basically "use a third-party app", but as far as I could tell that was a slightly different issue, related to Explorer being busy. If the solution for this turns out to be the same, fine, but I'd prefer a native fix if at all possible. Note: I've tagged this with Windows in general because I seem to remember it happening on Windows 7 as well as XP, but I rarely notice it because I use the start-menu search in preference to desktop shortcuts.

  Read the article

• Login with Enterprise Principal Name using sssd AD backend in Ubuntu 14.04 LTS

  - by Vinícius Ferrão

  I’m running sssd version 1.11 with the AD backend in Ubuntu 14.04 LTS (1.11.5-1ubuntu3) to authenticate users from Active Directory running on Windows Server 2012 R2, and I’m trying to achieve logins with the User Principal Name for all users of the domain. But the UPN are always Enterprise Principal Names. Let-me illustrate the problem with my user account: Domain: local.example.com sAMAccountName: ferrao UPN: [email protected] (there’s no local in the UPN) I can successfully login with the sAMAccountName atribute, which is fine, but I can’t login with [email protected] which is my UPN. The optimum solution for me is to allow logins from sAMAccountName and the UPN (User Principal Name). If’s not possible, the UPN should be the right way instead of the sAMAccountName. Another annoyance is the homedir pattern with those options in sssd.conf: default_shell = /bin/bash fallback_homedir = /home/%d/%u What I would like to achieve is separated home directories from the EPN. For example: /home/example.com/user /home/whatever.example.com/user But with this pattern I can’t map the way I would like to do. I’ve looked through man pages and was unable to find any answers for this issues. Thanks,

  Read the article

• A-2-Z web hosting on Amazon AWS

  - by JDelage

  All, I am studying web dvp, and one of my classes is project-based. We have to build a functional site that demonstrate our understanding of: HTML, CSS, Javascript, php, MySQL, And potentially Ajax or some other web component. For the project, we can use a local server using WampServer and basically build the site entirely on our laptop. If I have time, I would like to create a real site, and I thought it would be a good way to familiarize myself with Amazon's AWS services. So if I purchase a domain name, can I rely on AWS to host the site from A-to-Z? I understand I can use AWS to host content, the database, and do the background computations, if needed. What else do I need and what are the parts that AWS cannot help me with? Second, is there good documentation for a beginner to navigate AWS and learn how to use it (either on Amazon, or some 3rd party sites, or even a good book, as long as is up to date). The ideal documentation would be a tutorial on creating a web site from a-to-z on AWS, as detailed as possible. As you can guess, I have limited understanding of the IT issues. I have 0 Linux or sysadmin experience, but this is a good opportunity to change that. I hope you can help me. Thank you, JDelage PS: Please keep the answers AWS-specific. At this point, I am only interested in alternative services to the extent that they plug a hole in Amazon's offering.

  Read the article

• App for family tech support tracking?

  - by slothbear

  I do tech support for several groups within my family. They usually have a document or notebook of questions for me. They often record my advice, but then ask me again later. Some communications are by email (nice record for me, although they never think to search). Some sessions are in person, usually with a followup email from me for the record. Which they forget about. I'm not trying to force them to be more 'professional', but I would like to streamline my support a bit, and give them a place to look for past answers. Some of them would like a standard place like that, rather than reasking me the same questions. The solution has to be free. And web-based, although email-in for questions would be great. I'll be doing most (all?) updating of the system. Mobile/iPhone access would be nice, but not required. Ideally, a system with topics and responses would be good, but I'd need a way to promote one response as 'the answer'.

  Read the article

• AD domain on web servers behind NAT - DNS issues?

  - by Ant

  I'm trying to setup an AD domain to manage the security between two Windows Server 2008 webservers that will sooner or later use NLB to balance website requests. I've hit a problem which I think is a simple solution and is down to DNS. My website domain is mydomain.com. The two servers are running behind a NAT firewall on the 10.0.0.0 IP range. I've setup the AD domain to be called ad.mydomain.com (as recommended by MS and a few other answers to questions on here). The second web server however doesn't want to join the domain, and gives an error pinning the problem on DNS - "ensure that the domain name is typed correctly" even though it queries the SRV record successfully and gets the correct DC back - dc.ad.mydomain.com. Doing a dcdiag /test:dns on the DC gives the Delegation error 'DNS Server dc.mydomain.com Missing glue A record'. I have a feeling I need to add something to the public DNS so that it in some way knows about ad.mydomain.com. Can anyone suggest whether I'm on the right track in adding something to the public DNS? Or whether it's something else? Many thanks

  Read the article

• Network to network VPN Centos 5

  - by Atul Kulkarni

  I am trying to follow "http://www.centos.org/docs/5/html/Deployment_Guide-en-US/ch-vpn.html#s1-ipsec-net2net" I have come up with the following On local router machine: in my ifcfg-ipsec0: ONBOOT=yes IKE_METHOD=PSK DSTGW=10.5.27.1 SRCGW=10.6.159.1 DSTNET=10.5.27.0/25 SRCNET=10.6.159.0/24 DST=205.X.X.X TYPE=IPSEC I have /etc/sysconfig/network-scripts/keys-ipsec0 file in place. On Remote Machine in the cloud if have /etc/sysconfig/network-scripts/ifcfg-ipsec1: TYPE=IPSEC ONBOOT=yes IKE_METHOD=PSK SRCGW=10.5.27.1 DSTGW=10.6.159.1 SRCNET=10.5.27.124/25 DSTNET=10.6.159.0/24 DST=38.x.x.x with its respective /etc/sysconfig/network-scripts/key-ipsec1 file. The DST in both cases are NAT'd external IPs. Is that a problem? I have made changes for port forwarding as well. When I try to bring the interfaces up it gives me output "RTNETLINK answers: Invalid argument". I am confused now and don't know what more to do? Any place I can digup what parameters were wrong? I really appreciate any help I can get. Thanks and Regards, Atul.

  Read the article

• How can I know if a replacement display is compatible with my laptop?

  - by moraleida

  I have an Acer Aspire 4810TZ from 2010 which I truly love - it's a 3 year old notebook that still carries on for about 5 to 6h straight off the battery. I've also invested in it with an SSD and extra RAM and it's fine for my use right now. I'd really rather not just dump it. Now... its screen is dead and I'm looking for replacement parts, but it turns out to be a kind of expensive display - AUO B140XW02 14" LED. US$ 125 was the cheapest I found here (Rio de Janeiro, Brazil). The official dealer sells them for US$ 175. I'm aware of How do I know if a LCD is compatible with my Laptop? and Can I replace a laptop screen with one of a different resolution? but the answers don't really help me in this case. Also Replacing an LCD screen in a laptop gives me a hint but I'm completely dumb at hardware so this is why i'm asking: Is it possible to buy an LCD or a lower grade LED screen with the same connectors? What characteristics should I look for to find out if a certain display is compatible?

  Read the article

• Allow opening a new tab with Ctrl+T on all websites in Firefox

  - by Martin J.H.

  In Firefox, certain websites and plugins (Adobe PDF Plugin) appear to "capture" the Control key, so that when I try to open a new tab using "Ctrl+t", nothing happens - or worse, something unexpected happens. Examples: On the Codecademy site, while editing code, Ctrl+T either does nothing, or (when Flash is disabled) switches the position of the two characters next to the cursor. When viewing PDF's with the Adobe PDF Plugin, Ctrl+T does nothing. Is there a way to disable this "feature"? I would like "Ctrl+t" to always "talk" to Firefox! Edit: After searching superuser deeper, this question is very similar to the questions: "How to prevent keystroke grabbing/hijacking by websites in Firefox?" "How do I prevent pages I visit from overriding selected Firefox shortcut keys?". The answers to these questions are interesting and relevant, but do not give a method on how to disable combinatinos such as "Ctrl+t". Maybe a modified Greasemonkey script is the easiest solultion. Edit 2 - Attempt at a solution The following UserScript (Use GreaseMonkey to install it) successfully captures Ctrl+t on some sites (Google Search site, for instance - PopUp "Gotcha" appears), but not on the Codecademy site. I found another question pertaining to this subject here: "How to forbid keyboard shortcut stealing by websites in Firefox". It was raised in 2010, and the consensus was: It can't be done. // ==UserScript== // @name Disable Ctrl T interceptions // @description Stop websites from highjacking keyboard shortcuts // // @run-at document-start // @include * // @grant none // ==/UserScript== // Keycode for 't'. Add more to disable other ctrl+X interceptions keycodes = [84]; var lastPressedButton = [0]; document.addEventListener('keydown', function(e) { //uncomment to find out the keycode for any given key // alert(e.keyCode ); if (keycodes.indexOf(e.keyCode) != -1 && e.ctrlKey) { e.cancelBubble = true; e.stopImmediatePropagation(); alert("Gotcha!"); } return false; });

  Read the article

• Performance: Nginx SSL slowness or just SSL slowness in general?

  - by Mauvis Ledford

  I have an Amazon Web Services setup with an Apache instance behind Nginx with Nginx handling SSL and serving everything but the .php pages. In my ApacheBench tests I'm seeing this for my most expensive API call (which cache via Memcached): 100 concurrent calls to API call (http): 115ms (median) 260ms (max) 100 concurrent calls to API call (https): 6.1s (median) 11.9s (max) I've done a bit of research, disabled the most expensive SSL ciphers and enabled SSL caching (I know it doesn't help in this particular test.) Can you tell me why my SSL is taking so long? I've set up a massive EC2 server with 8CPUs and even applying consistent load to it only brings it up to 50% total CPU. I have 8 Nginx workers set and a bunch of Apache. Currently this whole setup is on one EC2 box but I plan to split it up and load balance it. There have been a few questions on this topic but none of those answers (disable expensive ciphers, cache ssl, seem to do anything.) Sample results below: $ ab -k -n 100 -c 100 https://URL This is ApacheBench, Version 2.3 <$Revision: 655654 $> Copyright 1996 Adam Twiss, Zeus Technology Ltd, http://www.zeustech.net/ Licensed to The Apache Software Foundation, http://www.apache.org/ Benchmarking URL.com (be patient).....done Server Software: nginx/1.0.15 Server Hostname: URL.com Server Port: 443 SSL/TLS Protocol: TLSv1/SSLv3,AES256-SHA,2048,256 Document Path: /PATH Document Length: 73142 bytes Concurrency Level: 100 Time taken for tests: 12.204 seconds Complete requests: 100 Failed requests: 0 Write errors: 0 Keep-Alive requests: 0 Total transferred: 7351097 bytes HTML transferred: 7314200 bytes Requests per second: 8.19 [#/sec] (mean) Time per request: 12203.589 [ms] (mean) Time per request: 122.036 [ms] (mean, across all concurrent requests) Transfer rate: 588.25 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 65 168 64.1 162 268 Processing: 385 6096 3438.6 6199 11928 Waiting: 379 6091 3438.5 6194 11923 Total: 449 6264 3476.4 6323 12196 Percentage of the requests served within a certain time (ms) 50% 6323 66% 8244 75% 9321 80% 9919 90% 11119 95% 11720 98% 12076 99% 12196 100% 12196 (longest request)

  Read the article

< Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >