Search Results

Search found 12264 results on 491 pages for 'drive letter'.

Page 153/491 | < Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >

  • Want to back up using dd, but my present ubuntu installation is 149.04 + 3.81(swap) GB, my target drive is only 149.05 GB

    - by Shreshth
    My netbook is a Windows7-Ubuntu 12.04 dual boot. in gparted the strcture looks like Partition filesystem size /dev/sda2 extended 152.86GiB __/dev/sda6 ext4 149.04GiB __/dev/sda5 linux-swap 3.81GiB /dev/sda3 ntfs 100MiB /dev/sda4 ntfs 145.13GiB /dev/sdb1 fat32 149.05GiB I want to backup my ubuntu 12.04 installation that is sda2 (sda6 + sda5) to sdb1. As you can see sda5 +sda6 is 152.86 GB where are sdb1 is only 149.05 GB. Can I backup only sda6(149.04GB) without losing any data? That is to say, will I be able to restore my ubuntu using only sda6 and later add the needed swap? Edit: Made it readable.

    Read the article

  • How does plugging in a SATA drive to an SAS backplane affect maximum cable length?

    - by user179658
    The limit on SATA cable length is 1m, whereas the limit on SAS cable length is 10m. When using a backplane which advertises support for SAS and SATA, with a SAS RAID controller and one SATA drive, will the controller use the SAS PHY scheme, allowing for the 10m cable length maximum (to accommodate the long backplane), or will it use the SATA one and allow for only the SATA cable length maximum of 1m?

    Read the article

  • I thought this parsing would be simple...

    - by Rebol Tutorial
    ... and I'm hitting the wall, I don't understand why this doesn't work (I need to be able to parse either the single tag version (terminated with /) or the 2 tag versions (terminated with ) ): Rebol[] content: {<pre:myTag attr1="helloworld" attr2="hello"/> <pre:myTag attr1="helloworld" attr2="hello"> </pre:myTag> <pre:myTag attr3="helloworld" attr4="hello"/> } spacer: charset reduce [#" " newline] letter: charset reduce ["ABCDEFGHIJKLMNOPQRSTUabcdefghijklmnopqrstuvwxyz1234567890="] rule: [ any [ {<pre:myTag} any [any letter {"} any letter {"}] mark: (print {clipboard... after any letter {"} any letter {"}} write clipboard:// mark input) any spacer mark: (print "clipboard..." write clipboard:// mark input) ["/>" | ">" any spacer </pre:myTag> ] any spacer (insert mark { Visible="false"}) ] to end ] parse content rule write clipboard:// content print "The end" input

    Read the article

  • A linq join combined with a regex

    - by Geert Beckx
    Is it possible to combine these 2 queries or would this make my code too complex? Also I think there should be a performance gain by combining these queries since I think in the near future my source table could be over 11000 records. This is what i came up with so far : Dim lit As LiteralControl ' check characters not in alphabet Dim r As New Regex("^[^a-zA-Z]+") Dim query = From o In source.ToTable _ Where r.IsMatch(o.Field(Of String)("nam")) lit = New LiteralControl(String.Format("letter: {0}, count: {1}<br />", "0-9", query.Count)) plhAlpabetLinks.Controls.Add(lit) Dim q = From l In "ABCDEFGHIJKLMNOPQRSTUVWXYZ".ToLower.ToCharArray _ Group Join o In source.ToTable _ On l Equals o.Field(Of String)("nam").ToLowerInvariant(0) Into g = Group _ Select l, g.Count ' iterate the alphabet to generate all the links. For Each letter In q.AsEnumerable lit = New LiteralControl(String.Format("letter: {0}, count: {1}<br />", letter.l, letter.Count)) plhAlpabetLinks.Controls.Add(lit) Next Kind regards, G.

    Read the article

  • shift reduce&& reduce reduce errors in build parser for python garmmer

    - by user366580
    i wanna build buttom up parser by java cup i write code in java cup , it is for python language so i used grammer was written in this site : but not all grammer , i choice partial set ,just while , identifer also i smiplified them when i did compile for the java cup that i write by write this command in command prompt window : java java_cup.Main -parser CalcParser -symbols CalcSymbol < javacupfile.cup i get conflict errors ,they are of type reduce-shift conflict and reduce-reduce conflict you can see to print screen of the errors in these links image 1 click here to see imge1 the grammer was in EBNF form in as refernce site and i convert it to BNF form maybe i make mistake in converting so i get such errors the origanl grammmer was // grammer in EBNF form identifier ::= (letter|"_") (letter | digit | "_")* letter ::= lowercase | uppercase lowercase ::= "a"..."z" uppercase ::= "A"..."Z" digit ::= "0"..."9 compound_stmt ::= if_stmt | while_stmt for_stmt ::= "for" target_list "in" expression_list ":" suite ["else" ":" suite] while_stmt ::= "while" expression ":" suite ["else" ":" suite] suite ::= stmt_list NEWLINE stmt_list ::= simple_stmt (";" simple_stmt)* [";"] simple_stmt ::= expression_stmt expression_stmt ::= expression_list expression_list ::= expression ( "," expression )* [","] expression ::= conditional_expression conditional_expression ::= or_test ["if" or_test "else" expression] or_test ::= and_test | or_test "or" and_test and_test ::= not_test | and_test "and" not_test not_test ::= comparison | "not" not_test comparison ::= or_expr ( comp_operator or_expr )* comp_operator ::= "<" | ">" | "==" | ">=" | "<=" | "<>" | "!=" | "is" ["not"] | ["not"] "in" or_expr ::= xor_expr | or_expr "|" xor_expr xor_expr ::= and_expr | xor_expr "^" and_expr and_expr ::= "&" | and_expr the grammer after converting to BNF form identifier ::=letterletter| letterdigit| letter"_"| "_"letter | "_"digit | "_""_" letter ::= lowercase | uppercase lowercase ::= "a"..."z" uppercase ::= "A"..."Z" digit ::= "0"..."9 while_stmt ::= "while" expression ":" suite "else" ":" suite |"while" expression ":" suite suite ::= stmt_list NEWLINE stmt_list ::= simple_stmt ";" simple_stmt stmt_list|";" simple_stmt ::= expression_stmt expression_stmt ::= expression_list expression_list ::= expression "," expression expression_list| "," expression ::= conditional_expression conditional_expression ::= or_test "if" or_test "else" expression |or_test or_test ::= and_test | or_test "or" and_test and_test ::= not_test | and_test "and" not_test not_test ::= comparison | "not" not_test comparison ::= or_expr comp_operator or_expr comp_operator ::= "<" | ">" | "==" | ">=" | "<=" | "<>" | "!=" | "is" ["not"] | ["not"] "in" or_expr ::= xor_expr | or_expr "|" xor_expr xor_expr ::= and_expr | xor_expr "^" and_expr and_expr ::= "&" | and_expr and the java cup file that i compile and get those errors is import java.io.*; terminal COMA; terminal ELSE; terminal WHILE; terminal NEWLINE; terminal SEMCOLON; terminal CAMMA; terminal IF; terminal OR; terminal AND; terminal NOT; terminal LESS; terminal GREATER; terminal EQUAL; terminal GREATERorE; terminal LESSorE; terminal NEQUAL; terminal OROP; terminal XOROP; terminal ANDOP; terminal Integer DIGIT; terminal java.lang.String LOWERCASE; terminal java.lang.String UPPERCASE; non terminal java.lang.String IDENTIFIER; non terminal java.lang.String LETTER; non terminal COMPOUND_STMT; non terminal WHILE_STMT; non terminal EXPRESSION; non terminal SUITE ; non terminal STMT_LIST; non terminal SIMPLE_STMT; non terminal EXPRESSION_STMT; non terminal EXPRESSION_LIST; non terminal CONDITITONAL_EXPRESSION; non terminal OR_TEST; non terminal AND_TEST; non terminal NOT_TEST; non terminal COMPARISON; non terminal COMP_OPERATOR; non terminal OR_EXPR; non terminal XOR_EXPR; non terminal AND_EXPR; IDENTIFIER ::=LETTER{: System.out.printf("lowercase"); :}| {: System.out.printf("uppercase"); :} LETTER{: System.out.printf("lowercase"); :}| {: System.out.printf("uppercase"); :}| LETTER{: System.out.printf("lowercase"); :}| {: System.out.printf("uppercase"); :} DIGIT; LETTER ::= LOWERCASE | UPPERCASE; COMPOUND_STMT ::=WHILE_STMT; WHILE_STMT ::= WHILE{: System.out.printf( "while"); :} EXPRESSION COMA {: System.out.printf(":"); :} SUITE ELSE {: System.out.printf("else" ); :} COMA{: System.out.printf( ":" ); :} SUITE |WHILE{: System.out.printf( "while" ); :} EXPRESSION COMA{: System.out.printf( ":" ); :} SUITE; SUITE ::= STMT_LIST NEWLINE{: System.out.printf( "newline" ); :}; STMT_LIST ::= SIMPLE_STMT SEMCOLON{: System.out.printf( ";" ); :} SIMPLE_STMT STMT_LIST|SEMCOLON{: System.out.printf( ";" ); :}; SIMPLE_STMT ::=EXPRESSION_STMT; EXPRESSION_STMT ::=EXPRESSION_LIST; EXPRESSION_LIST ::= EXPRESSION CAMMA{: System.out.printf( "," ); :} EXPRESSION EXPRESSION_LIST| CAMMA{: System.out.printf( "," ); :}; EXPRESSION ::= CONDITITONAL_EXPRESSION; CONDITITONAL_EXPRESSION ::= OR_TEST IF{: System.out.printf( "if"); :} OR_TEST ELSE{: System.out.printf("else"); :} EXPRESSION |OR_TEST; OR_TEST ::= AND_TEST | OR_TEST OR{: System.out.printf( "or"); :} AND_TEST; AND_TEST ::= NOT_TEST | AND_TEST AND{: System.out.printf( "and"); :} NOT_TEST; NOT_TEST ::= COMPARISON | NOT{: System.out.printf("not"); :} NOT_TEST; COMPARISON ::= OR_EXPR COMP_OPERATOR OR_EXPR ; COMP_OPERATOR ::= LESS{: System.out.printf( "<"); :} | GREATER{: System.out.printf(">"); :} | EQUAL{: System.out.printf("=="); :} | GREATERorE{: System.out.printf(">="); :} | LESSorE{: System.out.printf("<="); :} | NEQUAL{: System.out.printf("!="); :}; OR_EXPR ::= XOR_EXPR | OR_EXPR OROP{: System.out.printf("|"); :} XOR_EXPR; XOR_EXPR ::= AND_EXPR | XOR_EXPR XOROP {: System.out.printf("^"); :}XOR_EXPR; AND_EXPR ::= ANDOP{: System.out.printf("&"); :} | AND_EXPR; can any one told me how can solve this errors to build parser correcrtly??

    Read the article

  • C# app fails to load Matlab DLL when running from a shared drive?

    - by jg
    I have a C# .NET 2.0 program that calls a Matlab .dll file that I created using Matlab Builder for .NET. This Matlab .dll file is a wrapper for a m file function that I need to call from my C# program. Everything works fine when I run this app from my local drive. However once I copy the app to a shared drive the Matlab dll fails when it's first loaded. I setup caspol to allow .NET programs to run from shared drives. Does anyone know what could cause this problem or a tool that I could use to easily figure out what the problem is? Thanks.

    Read the article

  • How do you data drive task dependencies via properties in psake?

    - by Jordan
    In MSBuild you can data drive target dependencies by passing a item group into a target, like so: <ItemGroup> <FullBuildDependsOn Include="Package;CoreFinalize" Condition="@(FullBuildDependsOn) == ''" /> </ItemGroup> <Target Name="FullBuild" DependsOnTargets="@(FullBuildDependsOn)" /> If you don't override the FullBuildDependsOn item group, the FullBuild target defaults to depending on the Package and CoreFinalize targets. However, you can override this by defining your own FullBuildDependsOn item group. I'd like to do the same in psake - for example: properties { $FullBuildDependsOn = "Package", "CoreFinalize" } task default -depends FullBuild # this won't work because $FullBuildDependsOn hasn't been defined yet - the "Task" function will see this as a null depends array task FullBuild -depends $FullBuildDependsOn What do I need to do to data drive the task dependencies in psake?

    Read the article

  • SQL SERVER – Puzzle #1 – Querying Pattern Ranges and Wild Cards

    - by Pinal Dave
    Note: Read at the end of the blog post how you can get five Joes 2 Pros Book #1 and a surprise gift. I have been blogging for almost 7 years and every other day I receive questions about Querying Pattern Ranges. The most common way to solve the problem is to use Wild Cards. However, not everyone knows how to use wild card properly. SQL Queries 2012 Joes 2 Pros Volume 1 – The SQL Queries 2012 Hands-On Tutorial for Beginners Book On Amazon | Book On Flipkart Learn SQL Server get all the five parts combo kit Kit on Amazon | Kit on Flipkart Many people know wildcards are great for finding patterns in character data. There are also some special sequences with wildcards that can give you even more power. This series from SQL Queries 2012 Joes 2 Pros® Volume 1 will show you some of these cool tricks. All supporting files are available with a free download from the www.Joes2Pros.com web site. This example is from the SQL 2012 series Volume 1 in the file SQLQueries2012Vol1Chapter2.2Setup.sql. If you need help setting up then look in the “Free Videos” section on Joes2Pros under “Getting Started” called “How to install your labs” Querying Pattern Ranges The % wildcard character represents any number of characters of any length. Let’s find all first names that end in the letter ‘A’. By using the percentage ‘%’ sign with the letter ‘A’, we achieve this goal using the code sample below: SELECT * FROM Employee WHERE FirstName LIKE '%A' To find all FirstName values beginning with the letters ‘A’ or ‘B’ we can use two predicates in our WHERE clause, by separating them with the OR statement. Finding names beginning with an ‘A’ or ‘B’ is easy and this works fine until we want a larger range of letters as in the example below for ‘A’ thru ‘K’: SELECT * FROM Employee WHERE FirstName LIKE 'A%' OR FirstName LIKE 'B%' OR FirstName LIKE 'C%' OR FirstName LIKE 'D%' OR FirstName LIKE 'E%' OR FirstName LIKE 'F%' OR FirstName LIKE 'G%' OR FirstName LIKE 'H%' OR FirstName LIKE 'I%' OR FirstName LIKE 'J%' OR FirstName LIKE 'K%' The previous query does find FirstName values beginning with the letters ‘A’ thru ‘K’. However, when a query requires a large range of letters, the LIKE operator has an even better option. Since the first letter of the FirstName field can be ‘A’, ‘B’, ‘C’, ‘D’, ‘E’, ‘F’, ‘G’, ‘H’, ‘I’, ‘J’ or ‘K’, simply list all these choices inside a set of square brackets followed by the ‘%’ wildcard, as in the example below: SELECT * FROM Employee WHERE FirstName LIKE '[ABCDEFGHIJK]%' A more elegant example of this technique recognizes that all these letters are in a continuous range, so we really only need to list the first and last letter of the range inside the square brackets, followed by the ‘%’ wildcard allowing for any number of characters after the first letter in the range. Note: A predicate that uses a range will not work with the ‘=’ operator (equals sign). It will neither raise an error, nor produce a result set. --Bad query (will not error or return any records) SELECT * FROM Employee WHERE FirstName = '[A-K]%' Question: You want to find all first names that start with the letters A-M in your Customer table and end with the letter Z. Which SQL code would you use? a. SELECT * FROM Customer WHERE FirstName LIKE 'm%z' b. SELECT * FROM Customer WHERE FirstName LIKE 'a-m%z' c. SELECT * FROM Customer WHERE FirstName LIKE 'a-m%z' d. SELECT * FROM Customer WHERE FirstName LIKE '[a-m]%z' e. SELECT * FROM Customer WHERE FirstName LIKE '[a-m]z%' f. SELECT * FROM Customer WHERE FirstName LIKE '[a-m]%z' g. SELECT * FROM Customer WHERE FirstName LIKE '[a-m]z%' Contest Leave a valid answer before June 18, 2013 in the comment section. 5 winners will be selected from all the valid answers and will receive Joes 2 Pros Book #1. 1 Lucky person will get a surprise gift from Joes 2 Pros. The contest is open for all the countries where Amazon ships the book (USA, UK, Canada, India and many others). Special Note: Read all the options before you provide valid answer as there is a small trick hidden in answers. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Joes 2 Pros, PostADay, SQL, SQL Authority, SQL Puzzle, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

    Read the article

  • How to bypass resume from hibernate

    - by Daniel Trebbien
    I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

    Read the article

  • How to bypass resume from hibernate [closed]

    - by Daniel Trebbien
    I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

    Read the article

  • CD-ROM Cant Be Accessed After Installing VMware Tools on VMware Server 2.0.2

    - by Optimal Solutions
    Using VMware Server 2.02, I set up a new VM (Windows XP Pro) applied all of the updates, added Windows addons from the install CD, etc... I got it to a stable point and up through that point I was able to access the CD-ROM drive (E: on my host). What I never did before was install "VMware Tools" and since it claims to give better mouse and video support, I gave it a shot. What it does is it places the install package in a virtual CD-ROM drive. I ran the install, no errors and it wants a reboot. I log back in after reboot and pop in the install CD for Microsoft Office 2003 and I receive the message "Please Insert A Disc Into Drive D:". Drive D: would be the next logical drive after the C: drive where I chose to install the OS. The message box sits there and if I click "Cancel", to return to Windows Explorer, the status bar seems to blink ever 1/2 second - as if its polling for a CD-ROM drive or something. No bangs or exclamations in the Device Manager for any hardware. I had taken a snapshot prior to the VMware Tools install and upon restoring it, the CD-ROM is back. I made copies of two other VMs, installed the VMware Tools on those VMs and both experienced the same issues: Windows 2003 Server and Windows 7 (32-bit). Has anyone seen this issue and know of a fix for this? It would be nice to have the better graphics and better mouse control AND use my CD-ROM drive as well! Thank you.

    Read the article

  • Backup software for incremental swapped-out drives?

    - by user13743
    We're using Acronis Home 11 to backup our main Windows machine at the office. We have a set of portable hard drives that we swap out each week, for redundancy. We have incremental sets ( a new diff of the entire series each night) building on each drive. However, from time to time, Acronis gets confused and sometimes makes a new full backup. This eats up a lot of drive on the disks. Also, I have to trick the Acronis script each time I swap out a drive and point it to the new incremental backup set. Finally, if a drive gets full, there's no way to partition the backup set on a drive. I found this out the hard way, and now one drive is full with one backup set. So now on the other drive, I have three folders of backup sets. When one starts to get full, I delete the oldest one and start a new set. That way one single drive never gets filled up with one single backup set. I'm looking for a backup software that can backup Windows in incremental sets, and doesn't get tripped up with swapped out drives. Is there a better solution?

    Read the article

  • Possible boot conflict?

    - by Evan Kroske
    I was installing Ubuntu on a computer on which Windows XP was already installed. The computer has multiple hard drive bays, so I decided to remove the XP HDD and install Ubuntu on a blank HDD when it was the only HDD in the system. Unfortunately, if I now try to boot Ubuntu with the Windows XP drive in the second slot, nothing will boot. However, if Windows XP is in the first slot, it will boot fine. Can anybody explain why this happens? When I was checking out the BIOS to see if something was messed up, I discovered that when Ubuntu is in the first slot, the BIOS doesn't recognize any HDDs. However, if XP is in the first slot, the BIOS recognizes both drives. Any hypotheses about why this happens? Edit: Here's the setup. I have an old server with seven SCSI HDD slots. I have five identical 68 Gb SCSI drives, but I can keep only two plugged in. XP is still installed on the first drive, but I reinstalled Ubuntu on the second drive and had Grub overwrite the XP bootloader on the first drive. Now, the setup works fine, and I can use Grub to load either XP or Ubuntu. However, if I plug in another identical blank HDD in the third slot, the computer recognizes only the XP drive and doesn't boot. Grub starts to load, then gives me a "disk not found" error. Running ls from the grub rescue prompt only shows one drive with two partitions. I guess this is a BIOS problem, but I'd still like to know what triggers it. What about a blank drive could cause the BIOS to freak out?

    Read the article

  • How to install a desktop environment onto Ubuntu Server -- but without internet access or a CDROM?

    - by James
    I am playing around with a computer which has no CDROM drive or internet access and I have installed Ubuntu Server onto it. I have that all up and running nicely but now I'd like to install Xfce, GNOME or something similar so I can load up a desktop environment from the command line if I wish. Obviously with internet access or a CDROM, this would be a simple task of using apt-get and it finding & retrieving the packages for me, I assume, but I do not have either. I do however have a USB drive and I have used Unetbootin to make it into a bootable drive with the Ubuntu Server disk image files on there. I have mounted the USB drive to /media/usb0 and tried the command "sudo apt-cdrom add -d /media/usb0" to get apt to recognise the USb drive as an "Ubuntu CD" -- a source of package files but apt-get doesn't seem to be finding Xfce.. I try "sudo apt-get install xfce" and "sudo apt-get install xfce4" but neither find the package.. I would prefer to have Xfce but GNOME would be OK too.. My question is, am I doing something wrong? I figured that the Ubuntu Server disk (or rather, my Ubuntu Server USB drive) might not have any desktop environment packages on there so I tried the Xubuntu Desktop disk too (again, from my USB drive). I tried "sudo apt-get install xubuntu-desktop" but it couldn't find the package - even though it is listed under the /casper/ directory in some MANIFEST file. Anyone see where I'm going wrong? Maybe apt-get install is looking somewhere other than my USB drive? Maybe my commands are wrong? Maybe the disks don't even have the desktop environments on!? Thanks in advance guys, any input would be much appreciated. Cheers - James

    Read the article

  • How to increase the speed between two external hard drives on my laptop?

    - by Roman
    Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

    Read the article

  • How to increase the speed between two external hard drives on my laptop?

    - by Roman
    Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

    Read the article

  • Transfer disk contents *without* cloning tools

    - by Chris Cummins
    Is it possible to "clone" a disk which contains programs by performing a copy of all the disk contents (preserving file attributes) from source to destination disk, and unplugging the source disk and changing the drive letter of the destination disk to match that of the source? Context I have a two disk Windows 8 system with a system drive and a data drive. Recently, the data drive developed a number of bad sectors leading to IO errors. I have been sent a replacement drive so I simply need to clone the contents of this data drive onto the replacement. The drive contents include documents & media, user folders (My Documents and related), and some programs (games etc). Problem The problem is that the bad sectors on the source disk causes most disk cloning tools to fail with read errors. Attempted approaches include: Disk clone from live boot environment with Acronis True Image. Fails due to read errors. Disk clone from live boot environment with Clonezilla. Fails due to read errors. Disk clone using Roadkil's Unstoppable Copier. Fails due to hardware timeouts in the HDD (application hangs indefinitely). A straightforward copy from source to destination disk using FreeFileSync (preserving file attributes and metadata). This succeeds. So at the moment I have a replacement disk which contains all of the data from the original disk. Now all I need to is somehow get Windows to replace all references to the old disk to the new one. Is this possible by simply swapping the assigned drive letters? Any help would be greatly appreciated, thanks!

    Read the article

  • NTFS 'Owner' missing when accessing hard disk from external USB adapter

    - by trismarck
    I have a hard drive with Windows XP SP3 installed on it. When the drive is connected through the standard SATA connector inside the laptop, everything works as expected. However when I remove the drive from the laptop and connect the drive to the external USB adapter, almost all files / folders lose the 'Owner' field contents. I was wondering why could that be. I've tried two USB adapters and this happens on each. I could take the ownership of all of the files, but this would overwrite the Owner value (the Owner value that is present when the drive is accessed through standard SATA connector in the laptop). //edit: if the hard drive is used through the USB adapter, I can't access most of the files, at least until I take ownership of the files (/folders). This is how it looks like: HDD inside USB adapter: HDD inside laptop: (note the Owner column) //edit: some of the files on the first screenshot have Owner field filled up. That's because I took the ownership of those files / folders to be able to access the files on the hard drive. //edit2: also, if the hard drive is connected through USB adapter and if I've took the ownership of some files by the 'ddd' user, then if i login as a different user (lets say 'eee' user), the owner field is _still_ empty: ddd user: eee user: eee user can't access the 'ddd' folder. Both users have Administrator priviledges.

    Read the article

  • IDE compatability with SATA image

    - by Ormis
    We had an old CNC machine's hard-drive fail recently. The hard-drive is an old 1275MB IDE (Seagate) and there were defiantly bad sectors on it. I was able to image the contents of the drive onto a drive in my computer before it became completely unusable (I used DD, replacing all bad sectors w/ 0s). After running a couple chdsks, the SATA drive will boot off of the image. This is great, but there's one problem. The CNC machine old and requires IDE, I've attempted to copy the currently booting image off of the SATA drive and onto IDE drives numerous times in numerous ways and every time I do so the machines return that a boot device cannot be found. Some other information: The file system is fat32, running windows 98 The SATA drive is an 80gb drive I have tried copying the image to three 20gb and two 80gb IDE drives I have checked the jumper on the back of the IDE drives when using them If anyone has any ideas, questions, suggestions, etc. please let me know. P.S. I would just put a fresh install of win98 on the machine if i had the installation media (so that's out of the question). And if it comes to it, this is my last week working here, so I'll leave that to my co-worker. EDIT: Also, I have tried using Clonezilla as well as straight up DD to copy the image to the IDE drives.

    Read the article

  • Triple-Boot + 4 partition Limit

    - by dsimcha
    I just bought a new hard drive so that I could convert my XP-only machine into an XP-Ubuntu-Windows 7 triple boot machine. Since the drive is absurdly huge (1 TB) I wouldn't mind throwing ReactOS into the mix, too. I just found out that master boot records are limited to 4 entries, meaning 4 primary partitions. I had Windows XP set up on my old drive as a boot partition, a program files partition and a media partition. Since I really didn't want to install XP from scratch, I cloned this setup on my new drive. This leaves me one MBR partition entry for installing Windows 7, Ubuntu and ReactOS. I'd like to avoid having to install XP from scratch like the plague, partly because it's supposed to be a safety net in case things go wrong with my other OS's and because I've invested a lot of time getting it set up exactly the way I like it. Here are the options I've considered and why I don't like them: Install Windows 7 on my media partition. This would work, but I prefer to keep my media partition completely separate from any OS, so that I can reformat an OS partition without affecting my media partition at all. Use wubi or something to install Ubuntu in the same partition as something else. Again, this is brittle. Move all my media to a logical drive on an extended partition. Create another logical drive on this extended partition for Ubuntu. The problem here is that extended partitions are rather brittle--if you nuke one, it renders the rest useless. Just put the old drive back in my computer and run XP off it. Use the new one for the other OS's. The problem here is that the old drive is slower and uses extra power, generates extra heat, etc. Can anyone suggest any other possibilities that I may have overlooked?

    Read the article

  • Recover file from NTFS after it was formatted twice

    - by Phil
    I'm running Linux Mint and have a 2TB drive that I formatted as NTFS. I copied ~120GB of files from another computer to the 2TB drive, removing the files from the other computer as I did so. When they were all on the 2TB drive, I zipped them up as file "Gold.tar.gz". Then I reformatted the 2TB drive as ext3 in a moment of absolute stupidity. I formatted the 2TB back to NTFS, but of course everything is gone. Here is what I have tried: TestDisk -- won't find any lost partitions or undelete files, just the current empty one PhotoRec -- seems to only find some broken text files and misidentify their extensions. It never finds the 100's of avi files I had (before the 120GB copy, I already had 750GB on the drive full of avi files) or anything else that would show me it's working properly. Using dd I recovered the first 512MB of the drive and went hunting through it. I found all of the file as MFT entries, including the file "Gold.tar.gz" in a 2048 byte MFT record. I'm looking now for some way of either (1) telling PhotoRec to look at that record, or (2) analyze the MFT record myself and discover the sectors holding the data; I can piece it all together using dd and join the binary output if it's fragmented. One last thing - from the moment I got this drive a few days ago to the incident, there were only file copies made to it and no deletes. I formatted as NTFS, then copied thousands of files, then made a tar.gz, then reformatted to ext3, then reformatted to NTFS again. I'm hoping that the size of the drive and fact that there was no file modification/deleting happening makes for minimal file fragmentation.

    Read the article

  • I (stupidly) converted a TrueCrypt encrypted disk to GPT in Disk Management: now TrueCrypt won't mount it

    - by asilentfire
    Backstory: After moving a Macrium Reflect disk image from my TrueCrypt external drive (with whole disk encryption) onto a unencrypted drive and using Windows PE with Macrium Reflect to restore my internal disk to the recovery image on the external unencrypted drive, my Windows 8 failed to boot. I then went back and also recovered the System Partition (looking now, it is currently EFI), but I still couldn't boot into my backup.. I was in a hurry to get online for something so I just did a clean install of Windows 8, without the backup.. After I installed Windows 8, I went into Disk Management out of curiosity to see if there were other partitions with Windows 8 that Macruim might have missed, and there is (by default) a Recovery Partition of 100MB. My memory of this is hazy, as I was trying to get up and running for an exam at 4 AM: Something in Disk Management prompted me to convert my encrypted external drive to GPT.. I have no idea why I did this, but I went ahead and allowed it to convert my TrueCrypt drive to GPT. Now, I can't mount the drive in TrueCrypt.. Disk Management sees it as Disk 1, Basic, and Unallocated. I tried converting it back to MBR with Disk Management, but no dice with TrueCrypt :( If I try to mount the disk in TrueCrypt I get the message: Incorrect password or not a TrueCrypt volume I should never have messed with a Truecrypt drive in Disk Management, but I did. I have important college work in that drive, and fear I have lost it forever. PLEASE HELP

    Read the article

  • VMworkstation Windows 7 vm from physical partition?

    - by rich
    Hi All, i have a machine with 2 disks. my secondary drive has two partitions, one of which is a windows 7 64 boot partition. I have VM workstation and i would like to make a VM from the physical partition (described above). Ideally this would boot from the live disk, but if i can make a vmdk from the two partitions on the secondary drive that would be fine. 1 issue is the drive is 140gig raptor of which the two partitions i want are 40g and 30g partitions. the rest of the space is unallocated. So if i make a vmdk i really need it to be fixed at say 80 gig. I have converter but i don't understand how i can make the vmdk using this... specs Drive 1: this drive is a 120 SSD, running the host OS (Windows 7 64bit) - i've got 95 gigs free on this Drive 2: 140 gig raptor, partition 1 40g is also a windows 7 64bit install, partition 2 is 35 gig with program files folder on it.. sorta of needed to get the vm to work. There is 65gig unallocated on this disk. Drive 1 will host drive 2 as a VM.. my hope.

    Read the article

  • I have a bad install of Windows on another hard drive and it won't let me install a fresh copy. How do I fix it in Ubuntu 12.04?

    - by Dana LaBerge
    Basically, there was a security issue in the drivers for my graphics card. It was a 64-bit card and I installed 32-bit Windows. Apparently, before SP1 was available, which fixed that issue, 6 trojan horses got in. They stopped SP1 from installing. After going through the ringer several times, I finally talked to a person who knew the problem. It was something about how the drivers tried to transfer between the 32-bit OS and the 64-bit card that left me open. Ever since, my computer has been slow and has had weird issues. Like tinypic wouldn't ever load. Also, certain programs wouldn't install. So I eventually talk to the dude that knew the problem and he takes the reigns and does some diagnostics. He tells me that to fix it I have to format the hard drive and do a fresh install. I'm okay with that because I was planning on it anyway, to upgrade to the 64-bit version. The problem is, how do I do that? I have the disk to install the new copy, but when I go to install it, it tells me I can't and to check the log file. However, I don't know where that log file is, and it wiped my install of Windows out. How do I find the file and as a different route to get to the goal, how do I zero out the drive from Ubuntu 12.04? (I installed the 64-bit version just the other day)

    Read the article

< Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >