Search Results

Search found 16032 results on 642 pages for 'everyday problems'.

Page 153/642 | < Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >

  • I/O Error on LG GSA-H12N DVD drive on Windows 7

    - by Ashwin
    I am facing an I/O Error when I try to burn DVD data discs on my LG GSA-H12N DVD drive on Windows 7. Note that I was able to do this same operation on the same hardware/software just a day earlier without any problems, but with Windows XP. The only change (AFAIK) has been the installation of Windows 7 to replace Windows XP on this PC. Here is the error I get when I try to burn a DVD data disc using CDBurnerXP 4.2.7.1801: Burning error occured An error occured while burning the disc. Most likely the disc is not usable. Usually these errors happen if the inserted media is not compatible to the drive or of poor quality. (devNTSPTI_IO_Error) Could not write to Disc (LBA: 52864 Length: 32). SCSI Pass-through Interface I/O Error. - 0xFF045D Note that there can be no problem with the discs since I have been using the same discs (from the same box) just before the Windows 7 installation with no problems. The only change has been Windows 7. I tried InfraRecorder v0.5 and ImgBurn v2.5 and got similar I/O errors: Note that Windows 7 lists the LG GSA-H21N drive as being compatible (see this link). I also checked the LG Drivers website and using the firware update from there updated the drive firmware from version UL01 to UL02. But, even this has not helped. The drive reads DVDs without any problem, but continues to produce coasters. Could someone help me figure out what is the problem? Thanks :)

    Read the article

  • Suggestions for Windows 8 migration [closed]

    - by Big Endian
    I'm thinking of migrating to Windows 8. At first I hated it, but I'm pretty sure the Windows 8 model is the future, and I don't particularly want to end up hating the future like my parents, frustrated and bewildered by anything past Windows XP. I'm currently running Windows 7 and my system has been accumulating some problems. It's probably an accumulation of issues from installing too much software, changing firewall settings, installing Ubuntu alongside Windows, and... well I'm not sure, but my computer has been buggy in unexpected ways lately (freezing and unfreezing, display driver crashing and recovering, and what I call "deep freeze/thaw cycle" where the mouse won't even move for a while). I'm good at solving computer problems, but I can't seem to get to the root of these and my best idea for fixing them is making sure I've backed up every file then re-installing the entire OS. Luckily for me, a new OS is just around the corner so this would be a good time to get two things out of the way at once. The problem I see is that the upgrade options I see are all "seamless". I don't want a seamless upgrade. I want to wipe the slate clean and start all over. Does this mean I will have to buy a full, new copy of Windows 8 rather than one of the cheaper upgrading options? Or does it not make since for me to go to Windows 8 given that I have a laptop, not a tablet? Maybe I should just re-install Windows 7, or even call good enough good enough, try to eliminate the bugs, and start with a fresh slate in 2-3 years after this computer eventually dies entirely from (inevitable) hardware failure. What would be the advantages or disadvantages and costs of each option, how would I go about upgrading to Windows 8 if that's the option I choose, and what is your personal opinion about my situation?

    Read the article

  • Is there any special way to force GoBack to work with Windows Vista and 7?

    - by dfree
    Norton/Roxio's GoBack doesn't work with Vista/7 for reasons unknown. I have tried several alternatives (Norton Ghost, RollbackRX, Norton Save and Restore), none of which offer the same functionality as GoBack. Not only does GoBack not eat up all your hard drive space while creating a legitimate fail safe for any pc problems, it also allows you to see ACTIVELY EXACTLY WHAT PROCESS ARE BEING EXECUTED ON YOUR COMPUTER. This feature (called Advanced Disk Drive Restore) also allows you to troubleshoot problems and determine causes for things in about half a second by seeing what is happening on your machine. It's how I learned everything I know about computers. GoBack also features something called Safe Try Mode where you can put it in SafeTry and then mess up the whole computer and when you come out of it, your computer will be exactly how it was before. Amazing for people who like to tinker without risking their machine stability. It also helps for that accidentally erased paper or whatever you may have erased. I believe GoBack installs a type44 partition around the drive, which loads prior to windows to allow this functionality. If you're going to recommend another program, please don't (unless it does all of the above). I've tried all the competition and nothing is as good. I just want my GoBack to work with 7 :) Any ideas of crazy ways to make this work?

    Read the article

  • Win 7: apps crash, then explorer crashes, then services fail, then boom

    - by snorfys
    Periodically, every 2-3 days one of my systems will go haywire: every app will crash search will fail via the start menu and then explorer will fail. Restarting explorer via taskmanager will cause it to fail again, then it'll BSOD and restart. The eventlog for when this happens goes something like this every time: ERROR: Session "ReadyBoot" stopped due to the following error: 0xC0000188 (supposedly not a problem) WARNING: The maximum file size for session "ReadyBoot" has been reached... (forget where I found out, but also 'not a problem') ERROR: Session "Circular Kernel Context Logger" stopped due to the following error: 0xC0000188 (again, supposedly not a problem) WARNING: The maximum file size for session "Circular Kernel Context Logger" has been reached... ERROR: Faulting application name: Explorer.EXE, version: 6.1.7600.16450, time stamp:... ERROR: Faulting application name: explorer.exe, version: 6.1.7600.16450, time stamp:... ERROR: Faulting application name: svchost.exe_iphlpsvc, version: 6.1.7600.16385, time stamp:... ERROR: The Service Name service terminated unexpectedly. It has done this 1 time(s) That last one happens a number of times but with a different service name. Then finally we have: ERROR: The Service Control Manager tried to take a corrective action (Restart the service) after the unexpected termination of the Server service, but this action failed with the following error: An instance of the service is already running. After that, I have my BSOD and logs complaining that windows started up without shutting down. It's a new machine: Intel i3 530 4gb RAM (Ran memtest for 4 hrs, no problems) 320GB WD/250GB Seagate HDDs (Happened on fresh installs on 2 separate HDDs) Win7 Pro/Ultimate x64 (wife's copy of pro, my copy of ult, no change) Fresh install + driver and windows update (happened without updates as well) I'm at a bit of a loss as to what I can look at next. Especially since it'll work like a charm for 2-3 days and then it's hooped for a night (I'm on it now in fact - no problems).

    Read the article

  • I can't connect to my network, except in safe mode

    - by eidylon
    My laptop cannot connect to my network all of a sudden except in safe mode. When it boots, it will show the networks available in the tray popup, but if I click connect on any, it says "Unable to connect" and the troubleshooter is useless. Shortly thereafter all the networks disappear. I have tried removing IPv6 support as I have seen that cause problems. No joy. I've also tried removing the wireless network adapter in Device Manager and reinstalling it, also no joy. I've also tried attaching a USB wireless adapter, and it has the same problem. If I boot in safe mode, then it has no problems at all. Three other devices in the house connect fine, so I am pretty sure it is nothing to do with the router. Any ideas what to check next? I am running Win7 Ultimate on a 2GHz Quadcore with 8GB RAM with a Broadcom 802.11n wireless card. EDIT: RE wired connections: What is very weird is that if i plug in a wired connection, then not only does it connect via the wired connection, but the wireLESS also starts working perfectly. And a soon as I unplug the wire, then the wireLESS stops working again! So it seems the wireless is right now working only in safe-mode, or when a wired connection is also plugged in.

    Read the article

  • Running a VM off a USB 2.0 Flash Drive - Mac/Parallels/XP

    - by geerlingguy
    I use a MacBook Air as my primary machine, and the 128GB SSD means space is precious. To save about 10 GB, I've been running Parallels with a Windows XP VM off an external USB hard drive, which performs as well in everyday use as running the VM off the internal SSD. So, I bought a tiny 32GB USB 2.0 flash drive, plugged it into the MacBook Air, formatted it first as ExFAT (which was slow), then as Mac OS Extended (Journaled) (which was also slow), and copied over my VM file, and ran Parallels off it. My full experience is documented here: http://www.midwesternmac.com/blogs/jeff-geerling/running-windows-xp-vm Straight file copies are really fast — 30 MB/sec read (solid the whole time), and 10-11 MB/sec write (solid the whole time). But I noticed that once XP started running, the disk access rates were in the low KB ranges. Are USB flash drives really that poor at random access, or could I possibly be missing something (the format of the flash drive, etc.?)? Of note, I've tried the following, to no great effect: Formatting the drive as either ExFAT or Mac OS Extended (Journaled) Unplugging all other USB devices and turning off Bluetooth (which runs on the right-side-port USB bus). Plugging in the flash drive either direct in the right side port, or the left side port, or into a USB 2.0 hub

    Read the article

  • How are spam e-mails filtered ?

    - by kevindqc
    Hello. I'm just wondering how some e-mails get past the spam filter, and some don't? Everyday I get World of Warcraft phishing emails that get past the filter... For example, here's a phishing email (just the header) I got in my inbox, and not in my junk mail: X-Message-Delivery: Vj0xLjE7dXM9MDtsPTA7YT0wO0Q9MjtTQ0w9Ng== X-Message-Status: n:0 X-SID-PRA: [email protected] X-AUTH-Result: NONE X-Message-Info: M98loaK0Lo27IVRxloyPIZmAwUHKn18nx0o/idLdvGYjK48i19NuvFOnRFYGWE+HdIrNJpi1XaYx0gaAV13cgRnkWSzgHKG1 Received: from blizzard.com ([204.45.59.37]) by SNT0-MC3-F21.Snt0.hotmail.com with Microsoft SMTPSVC(6.0.3790.3959); Sat, 10 Apr 2010 06:38:24 -0700 Received: from hxeabjlh ([192.168.1.165]) (envelope-sender <[email protected]>) by 192.168.1.111 with ESMTP for <[email protected]>; Sat, 10 Apr 2010 08:43:24 -0500 Reply-To: <[email protected]> Sender: [email protected] Message-ID: <DE567AFB9E2F3DD985A2D9A8D12D2917@hxeabjlh> From: "[email protected]" <[email protected]> To: <[email protected]> Subject: World of Warcraft Account Password verification Date: Sat, 10 Apr 2010 21:38:10 +0800 MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="----=_NextPart_000_04EE_0137659E.1AA23350" X-Priority: 3 X-MSMail-Priority: Normal X-Mailer: Microsoft Outlook Express 6.00.2900.5512 X-MimeOLE: Produced By Microsoft MimeOLE V6.00.2900.5512 Return-Path: [email protected] X-OriginalArrivalTime: 10 Apr 2010 13:38:24.0607 (UTC) FILETIME=[17F3A6F0:01CAD8B3] From what I understand, when you send an email with SMTP, you can specify any hostname in the "HELO" command. Here, the spammer specified "blizzard.com". And he sent his email through Hotmail using Outlook Express. I just don't understand how this gets past the spam filter? There's this SPF thing that seems to exist... but it doesn't seem to be used by blizzard? I'm on Windows, and if I use nslookup to look for the TXT records of blizzard.com and worldofwarcraft.com, I don't see a thing.... so blizzard is not using SPF? Why would that be?

    Read the article

  • Dedicated server automatic backup solution

    - by Luigi
    I have a dedicated Ubuntu web server in a cloud environment, and I am looking for a nice way to do automated backups. I would like to backup some directories with web apps, and all my MySql databases. As for destination: make snapshots every two hours localy, and every six hours to a remote ftp server. Also delete backup archives older than seven days(localy + ftp), and notify on any problems by email. Now to achieve some of this functionality I use cron + shell script, and http://www.mysqldumper.net/, but really that doesn't answer my needs. Mysqldumper doesn't know automaticly about new databases, and shell script does not notify on problems. It's something I have to check out from time to time, and i don't have trust for. I googled a while, and seems like most people solve this stuff with shell scripts. Is this a method you can trust? Are there any web-gui tools, I'm missing? Maybe there is a smarter startegy for doing this? I'm a little bit confused.

    Read the article

  • samba "username map" stopped to work after upgrade to 3.6

    - by Kris_R
    It was time to upgrade our group server (new HDs, problems with old installation of DRBD, etc..). Going as usually for CentOS i upgraded whole system from 6.3 to 6.4 The later one came with samba 3.6 as the old one was 3.5. I transferred most of users by copying /etc/password, /etc/shadow and samba accounts with pdbedit. Homes were on nfs-drive. The translation of unix accounts to samba accounts are located in /etc/samba/smbusers. Strangely enough on some windows clients there was problem to connect to samba-shares. In one case the only thing that worked was, instead of giving windows name, to use the unix account. In another one, it was possible to mount network drive and to open it in Windows Explorer, however other applications like "Total commander" at the attempt of opening this drive gave the message "Cannot connect to z:" (sometimes at this moment user/pass were requested). The smb.conf has following entries: [global] security = user passdb backend = tdbsam username map = /etc/samba/smbusers ... [Kris] comment = Kris's Private path = /SMB/Users/Kris writeable = yes read only = no browseable = yes users = krisr printable = no security mask = 0777 force security mode = 0 directory security mask = 0777 force directory security mode = 0 force create mode = 0775 force directory mode = 6775 The smbusers: # Unix_name = SMB_name1 SMB_name2 ... krisr = Kris Of course testparm runs without any errors. I was used from samba 3.5 to outputs of form Mapped user kris to krisr. Nothing like this happens now. Just message check_sam_security: Couldn't find user Kris in passdb. I read on web that some guys had problem with 3.6 and security = ADS, but these were not helpful for me. I'm seriously thinking about downgrading back to samba 3.5 but before this step I wanted to ask if somebody knows the solution of these problems.

    Read the article

  • AWS Linux EC2: yum won't run with plugins

    - by Patrick
    Short Version: yum commands on my Amazon Linux EC2 AMI only work with --noplugins. Long Version: A couple of days ago, I ran yum update at the behest of the SSH Login MoTD telling me I had updates to install. About midway through the update (specifically while updating the kernel), the update abruptly ended (79 of 138 items completed). The website I host on EC2 got weird for a few minutes, but eventually seemed to stabilize back out (maybe EC2 restarted itself?), and I didn't have further issues (other than MySQL started running out of memory, but I think that's probably unrelated to this). Today, I went to install gcc-c++ (with yum install gcc-c++). When I did, I got the following message: Loaded plugins: priorities, security, update-motd, upgrade-helper Config error: Command "updateinfo" already defined and I get that for any command I can think to run using yum. However, If I throw in the --noplugins flag, then magically it seems to work. To be clear, when I installed a different package a week ago, it worked totally correctly, so the yum update is the only thing I can think of that changed. I could find nothing on Google with regard to "updateinfo" already defined (with and without quotes). I tried running yum update --noplugins which spit out a message telling me that I should have run yum-complete-transaction instead, but proceeded to try to update something on its own. When that completed, I tried yum-complete-transaction but that gave me a message about the transactions not lining up correctly, so it removed the old transaction (Probably since I should have completed the first transaction before trying to update again, if I had known). Based on the SF question "Linux EC2 Broken Yum", I've also tried yum clean all --noplugins (fails the same with plugins) which just gives me Cleaning repos: amzn-main amzn-updates rpmforge Cleaning up everything I also tried package-cleanup --problems Loaded plugins: priorities, update-motd, upgrade-helper No Problems Found and package-cleanup --dupes Gives a lot of dupes, so I pasted them here: http://pastebin.com/VVFQEkTT instead of inline. At this point, I'm not sure what else there even is to check.

    Read the article

  • What are best practices on virtual lab/test bed architecture?

    - by WooYek
    I am currently preparing a new small virtual environment for development and testing with Windows Server + SQL Server + AD + Sharepoint + Exchange + IIS(ASP.NET) + Biztalk + ?, for a small (up to 5) dev team. What are pros and cons on different approaches, eg. splitting up over different machines or packing everything up per machine. I your experience what are the best practices I should follow in terms of architecture and various system/servers placement. What to share and what to split per person. I would like to achieve some flexibility for the dev and testing process (so teammebers would not be steeping on each other's toes) and limit administrative effort needed to propagate settings, integrate work items and revert changes when something breaks up. It's not supposed to be an everyday development working environment, more a tier 2 developer testing environment, and not yet an integration or QA testing environment with formal change process. IMO the two borderline solutions are: creating one all-inclusive machine for each dev team member giving them freedom to manage creating shared environment managed by the one with somehow formalized change request process What golden mean would you recommend, and why?

    Read the article

  • BSOD during Cygwin install

    - by Mike Pennington
    I have been running Cygwin (1.7.7) under Windows Vista 64-bit, SP2 for at least a year, and had no problems with my installation at all until today. When I tried to install apt-cyg, I realized that I needed to get the svn client. During the installation of the package dependencies, Vista threw a blue screen of death. I hoped this was a one-time occurrence, so I rebooted into Vista and tried to install svn again; same result. Next I completely removed Cygwin's directory, and all Cygwin registry entries; at this point, I tried reinstalling the base Cygwin system again. During the installation of bash, I got another BSOD: Apologies for the fuzzy pic, I had to shoot with my phone camera. I googled for BSOD and Cygwin and found a post by Dave Korn mentioning that the only reasons Cygwin should cause a BSOD is because of either ioperm.sys or some USB utilities. I have neither on my system. Every time I have tried reinstalling, Vista BSODs; I have not had problems installing any other software packages on this Vista machine. How can I get Cygwin installed again (without reinstalling Vista)?

    Read the article

  • Changes to grub in ubuntu 10

    - by jdege
    I've been running CentOS 5 for some years. I've decided to upgrade to Ubuntu, and with 10.04 just out, this seemed like a good time. I'm a tad paranoid, so I started off with a new set of drives - one to install on, one to backup to, and one as a spare. I removed my existing CentOS 5 drives, and did an install, and had no problems. I installed the server version, and used the default full-disk LVM installation. Next, I copies my backup scripts over, edited them to work with the new configuration, and did a test backup. That worked fine, as well. Then comes the real test, could I do an install of the backup onto the spare drive? (I won't put anything of importance on a system that doesn't have a reliable backup, and if I've never done a restore, it's not reliable.) I booted from a System Rescue CD (ver 1.5.3), with the spare drive as /dev/sda, and the backup drive as /dev/sdb. I had no trouble in partitioning, configuring LVM, formatting, making swap, or restoring the file systems. But when I got to restoring grub to the MBR, I ran into problems. My restore instructions from CentOS 5 said run grub, then enter two commands: root (hd0,0) setup (hd0) The first command exits with an error: "Checking if /boot/grub/stage1 exists ... no" I did some googling around, and found that the Grub2 included in recent Ubuntus is very different than the Grub 0.97 included in CentOS 5. One site suggested I use: grub-install --root-dir=/mnt/restore /dev/sda That appeared to work, but when I booted from the drive, I ended up at a grub prompt. Any ideas as to what I need to do? It seems like a simple problem, but my attempts at searching out answers on the web are being swamped by references to the old version of Grub. Help would be appreciated.

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • PHP Script Won't Run - Apache2/MySQL Servers Running, PHP Installed - Ubuntu 10.04

    - by nicorellius
    I am trying to install a CRM on a Linux (Ubuntu 10.04) laptop to do some testing. Installing the current versions of Apache, MySQL and PHP, and getting the CRM to run is easy. It's when I try to go backwards and run it on a previous set of versions I run into problems. This is what I have done: I have installed Apache 2.2.14, MySQL 5.0.83, and PHP 5.2.8. When I type something like mysql --version I get back what I would expect: version and distribution info. The same goes for Apache2 and PHP. The Apache server is running and so is mysqld. So when I go to my browser and look at http://localhost/<CRM dir>/install.php Firefox offers to open the PHP file or save it, as if it doesn't recognize the file. What should happen is that I should get a welcome page and the installation wizard for this CRM distribution should start. I have tried so many different things I probably screwed up something along the way. I have restarted the servers over and over, and even recompiled the versions of MySQL and PHP with no problems. I am hoping I am overlooking something simple because I am lost. Any help is appreciated.

    Read the article

  • Ensure Mac's get correct machine name from DHCP?

    - by Greg Whitfield
    I have a problem in our network where our Mac's occasionally get given the wrong machine name while, I guess, getting a new DHCP lease. The DHCP servers are Windows based - the bulk of our network is Windows, but we have some Linux machines and an increasing number of Macs. The problem specifics is that occasionally a Mac will take on the name of another machine in the network. For example, I have a new Macbook Pro. In the OSX setup is gets called "gomez", and initially starts up on the network with that name without any problems. But after a few days when the machine was restarted (it had several restarts in the meantime), it ended up being called "florrie", which is actually the name of another machine in another part of the network. All network ops work fine, and indeed you don't notice most of the time - it's only when you run apps like Perforce that require the hostname that you get problems. I'm sorry I don't have more info than that, but if I know what to look for I can dig out some more facts. Or any hints on checking the network setup would be useful.

    Read the article

  • SCCM 2012 Clients no longer detecting

    - by user3685428
    Here is the scenario I had a fully functioning SCCM 2012 site server with the DP, MP, SUP, Application catalog, etc. roles configured and working. There is only one server on this site. Everything was great but i was not happy with SUP, so i decided to create a separate WSUS server and configure Windows Updates through GPOs. That setup worked great as well so i went ahead and removed the SUP role from SCCM and removed the WSUS feature from my SCCM server (they were configured on the same SCCM Server). I did not notice any problems right away. A couple days later i noticed that the OSD deployments were giving errors, and after a couple hours of trying suggestions from Google, i was able to uninstall PXE and make a few changes and reinstall with WDS to get it working again. Again, thought everything was fine and continued on. The last couple days i have noticed that any new machine deployed or installing the Client will show in the SCCM console as "No" Client. The client machines will show connected to a site but the software center shows "IT Organization" instead of our site like the previous clients. The existing clients all seem to be functioning normally. they still receive application distributions and configuration baselines, etc. Reinstalling, uninstalling and reinstalling, repairing does not fix the problems and this happens on all new clients. ClientLocation.log shows it connecting to the correct MP. Nothing odd in any of the logs except for the ClientMessaging.log which repeats continuously this line: <![LOG[Raising event: instance of CCM_CcmHttp_Status { ClientID = "GUID:0450fde3-ab82-41bf-9c33-87a18113744b"; DateTime = "20140528214824.993000+000"; HostName = "SOUNDWAVE.domain.org"; HRESULT = "0x00000000"; ProcessID = 4092; StatusCode = 0; ThreadID = 3720; }; ]LOG]!><time="16:48:24.994+300" date="05-28-2014" component="CcmMessaging" context="" type="1" thread="3720" file="event.cpp:706"> thanks

    Read the article

  • ADSL to T1, Is it worth it for us?

    - by Jack Hickerson
    The company I work for has roughly 45-55 simultaneous users (local and remote/VPN) logged in at a given time. We currently subscribe to an ADSL connection but we have been experiencing slower upload/download speeds as our number of users increase. So, I have a few questions with regards to upgrading our connection to a t1 line. I am aware that the number of channels on a t1 line are much greater then that of our current ADSL connection, but I have heard that the number of active users on a t1 line should be no greater than ~30 for optimal performance. I would think this statement is dependent on what each user was using the connection for and could change depending on this variable. That being said, I have tried to break down how the line would be used in our organization based on our major departments: Sales (~60% of total users) - Everyday surfing, email, research, occasional streaming media Marketing (~15% of total users) - Heavy reliance on uploading/downloading, streaming media, file sharing Other (~25% of total users) - email, rare use of any connection intensive activities. I have considered keeping the ADSL for our local users and dedicating the t1 to our remote users (or vice versa) but the cost is significantly higher then what we had hoped for. All factors being equal (# of users, frequency of downloads/uploads from our current activities) Would you suspect a significant performance increase in making the transition to a t1 line from our current ADSL line? What are your thoughts or recommendations?

    Read the article

  • Apache and linux file permissions

    - by morpheous
    I recently moved a Symfony 1.3.2 website (a PHP web framework), from a windows machine to Linux (Ubuntu 9.10). Ever since then, I have had all kinds of problems involving file permission (even though the app run without any of these problems on windows). I run symfony fix-perms which applied a 777 mask to the web directory (presumably, including its sub folders) - (as an aside) I think that is a potential security hole ... I have been meaning to come in here to ask how to correctly set permissions. Currently, when attempting to save a file from my website, I am getting the following error: PHP Warning: imagejpeg() [0function.imagejpeg0]: Unable to open '/home/morpheous/work/webdev/frameworks/symfony/sites/project1/web/uploads/../images/thumbnail/959cd604cf6115014a3703bef5a50486a5520642.jpg' for writing: Permission denied in /home/morpheous/work/webdev/frameworks/symfony/sites/project1/apps/frontend/lib Here are the permissions on the folders: web drwxr-xr-x 16 morpheous morpheous 4096 2010-02-24 21:01 web web/uploads/../images drwxr-xr-x 13 morpheous morpheous 12288 2010-04-09 15:25 images web/uploads/../images/thumbnail drwxr-xr-x 3 morpheous morpheous 4096 2010-02-24 20:44 thumbnail Can someone kindly tell me how to set the permissions so that my website (presumably running as the Apache daemon) can write the files to the directory required above?

    Read the article

  • Cannot access drive in Windows 7 after scandisk lockup, but can in safe mode....

    - by Matt Thompson
    I ran scandisk on my external USB drive due to the inability to delete a few files. Windows asked me if I wanted to unmount the drive before the scan, warning me that it would be unusable until the scan was finished, and I said yes. During the scan, my machine locked up, and I was forced to reboot the machine. When it came up, I was unable to access the drive, getting an error that "L:is not accessible, access is denied". Comupter Management sees the drive, and has the proper amount of disk space filled. I booted into safe mode, and can access the drive with no problems, and I noticed that in explorer, all the folders have locks on them. I booted back into windows, but still could not access the drive, getting the same error as above. Hovever, if I right click on the drive, select properties, and go to Customize, in the folder pictures ares, I select Choose File, and a window open up, that shows the root of the directory, with all the folder able to be accessed, but again, the icon is the folder icon with a lock on it. I can even copy files from the drive to another. So, the files are not gone, windows can obviously access the drive no matter what it thinks, so there has to be a problem with the flag windows put on the drive when it ran the original scan that failed. I was able to run a scan both in safe mode with no problems, and in windows. In windows, I received the cannot access error the first time I run scan disk on it, but if I try again, it works fine. Any ideas on how to clear the flag that windows set, so I can access the drive normally again?

    Read the article

  • Error importing large MySQL dump file which includes binary BLOBs in Windows

    - by Daniel Magliola
    I'm trying to import a MySQL dump file, which I got from my hosting company, into my Windows dev machine, and i'm running into problems. I'm importing this from the command line, and i'm getting a very weird error: ERROR 2005 (HY000) at line 3118: Unknown MySQL server host '+?*á±dÆ-N+Æ·h^ye"p-i+ Z+-$?P+Y.8+|?+l8/l¦¦î7æ¦X¦XE.ºG[ ;-ï?éµ?º+¦¦].?+f9d릦'+ÿG?-0à¡úè?-?ù??¥'+NÑ' (11004) I'm attaching the screenshot because i'm assuming the binary data will get lost... I'm not exactly sure what the problem is, but two potential issues are the size of the file (2 Gb) which is not insanely large, but it's not trivially small either, and the other is the fact that many of these tables have JPG images in them (which is why the file is 2Gb large, for the most part). Also, the dump was taken in a Linux machine and I'm importing this into Windows, not sure if that could add to the problems (I understand it shouldn't) Now, that binary garbage is why I think the images in the file might be a problem, but i've been able to import similar dumps from the same hosting company in the past, so i'm not sure what might be the issue. Also, trying to look into this file (and line 3118 in particular) is kind of impossible given its size (i'm not really handy with Linux command line tools like grep, sed, etc). The file might be corrupted, but i'm not exactly sure how to check it. What I downloaded was a .gz file, which I "tested" with WinRar and it says it looks OK (i'm assuming gz has some kind of CRC). If you can think of a better way to test it, I'd love to try that. Any ideas what could be going on / how to get past this error? I'm not very attached to the data in particular, since I just want this as a copy for dev, so if I have to lose a few records, i'm fine with that, as long as the schema remains perfectly sound. Thanks! Daniel

    Read the article

  • Cannot Connect To VMWare Guest OS Using Either RDP or VNC

    - by Humanier
    Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

    Read the article

  • Cannot Connect To VMWare Guest OS Using Either RDP or VNC

    - by Humanier
    Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

    Read the article

  • Problem with Windows Service and network printers.

    - by Mohammadreza
    I have a Windows Service application that every now and then should print some documents. As far as I know, to print those documents, my service must be run with a user account other than Local Service or Network Service. So i have created a user account and added that to the Administrators group and ran the service with it. With locally installed printers, I don't have any problems because those printers are automatically installed for all accounts. To be able to print with the network printers, I have created another application that syncs the installed printers of the currently logged in user with the user account that my service uses with the rundll32.exe printui.dll,PrintUIEntry command. In Vista and Windows7 I don't have any problems with the syncing of the printers because every time that a printer should be installed the authentication window will open and it asks for the appropriate user account to install that printer (The service user account is not created on the network printers computers) but in XP a find dialog with the "Connecting to {printername}" caption will appear and stops responding, or sometimes it installs the printer but every time service tries to print, a Win32Exception with "A StartDocPrinter call was not issued" message will throw and in the user account that runs the sync application a duplicate printer will be shown and I couldn't delete those printers unless with force (using registry). Am I doing the right thing for printing documents with Windows Services at all? If yes, how can I solve the above-mentioned problem? And if not, what the heck should I do? Thanks.

    Read the article

  • Windows 2003 R2 zip program blocking EXE file

    - by Harvey Kwok
    I have a Windows 2003 R2 Enterprise Edition SP2 32-bit machine with all latest patch (as of 1-6-2011). It's a VM. I have a zip file, including a pdf file, a txt file and a exe file. If I copy the zip file onto the machine via a shared network drive, I can unzip all the files properly without problems. If I put the zip file on my web server and then I download it from there, I can only unzip the pdf file and txt file. The exe file is silently ignored. I searched the web and found somebody reporting similar issue on XP. If I right click on the zip file downloaded from the web server, at the bottom of the general page, it has a warning message saying that "This file came from antoher computer and might be blocked to help protect this computer" I understand that I can solve the problem by simply clicking the "Unblock" button and extract the file again. The things that bothering me is that why the warning message says "might be blocked"? I tried downloading the same zip file from the same web server on to my Windows 7 box with latest patch. It also shows the same warning message. However, even with the warning message, I can extract all the files properly without clicking the "Unblock" button. Is it a bug in Windows 2003 R2 SP1? Is there any security settings controlling this? How likely will the end user seeing this problem? I want to dig into this because I am worrying people downloading my zip file from my web server might see similar problems. The first thought coming to the user's mind will be the zip file is somehow corrupted. Honestly, I didn't know this "Unblock" feature in Windows before I run into this problem. EDIT I just tried it on another Windows 2003 R2 SP1 machine. The zip program doesn't block the EXE file on that machine either. Both Windows 2003 R2 SP1 machines are joining to the same forest.

    Read the article

< Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >