Search Results

Search found 10078 results on 404 pages for 'micro controller'.

Page 153/404 | < Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >

  • Struggles to connect to network when using WPA with a BCM43225

    - by pst007x
    When booting my laptop, it will try to connect to my wireless network, however a window keeps popping up asking me for my security password, which has already been saved. I have to keep deleting my network settings, and reconnecting, otherwise it keeps failing to connect. My wireless is set up with a WPA, I do not want to lower my security because of this, but it is a pain and can take me 15mins plus to finally connect. The problem has only become apparent since a fresh install of 11.10. IPV6 disabled. System info: 01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01) Subsystem: Acer Incorporated [ALI] Device 036d Flags: bus master, fast devsel, latency 0, IRQ 43 Memory at b3400000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: tg3 Kernel modules: tg3 02:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01) Subsystem: Broadcom Corporation Device 04da Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at b2400000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: wl, brcmsmac ADDITIONAL: In terminal I get this: pst007x@pst007x-ubuntu64:~$ nm-applet start ** Message: applet now removed from the notification area ** (nm-applet:2816): DEBUG: old state indicates that this was not a disconnect 0 ** Message: using fallback from indicator to GtkStatusIcon ** Message: applet now embedded in the notification area ** Message: No keyring secrets found for Auto Access 01/802-11-wireless-security; asking user. ** (nm-applet:2816): DEBUG: foo_client_state_changed_cb Note this line: ** Message: No keyring secrets found for Auto Access 01/802-11-wireless-security; asking user. At this point is where I am asked for the password. Please report WPA issues with Ubuntu 11.10 here: https://bugs.launchpad.net/ubuntu/+source/network-manager/+bug/892727

    Read the article

  • Problems with Intel Video Resolution on Acer Laptop Wide Display

    - by ricstr
    I have an ACER Aspire 5332 laptop which I have just installed Ubuntu 12.04 x64, which is causing some issues with the video display on boot and video resolution. First and foremost, it will only boot past the purple screen if GRUB has been edited to replace 'quick splash' with 'nomodeset'. Secondly, once it has booted with the the 'nomodeset' option, it does not allow me to change the resolution higher or lower from 1024 x 786. Is it OK to use the 'nomodeset' for normal use? Will this compromise performance of other devices? The video card is an on-board one, integrated within the Intel GL40 chip-set. The display is a wide-screen LCD, and under Windows could operate under various resolutions. Ideally I would like it to operate on a resolution to fit the wide-screen display as it a bit stretched out at the moment, and less desktop space as I am used to. I believe the optimal resolution is 1366 x 768. Below is some information from the terminal which may be useful. ricstr@Aspire-5332:~$ lspci | grep -i VGA 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09) ricstr@Aspire-5332:~$ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 1024 x 768, current 1024 x 768, maximum 1024 x 768 default connected 1024x768+0+0 0mm x 0mm 1024x768 0.0*

    Read the article

  • Why are my videos playing speeded up with no audio, but work fine if I log in as a guest?

    - by Martins Kruze
    Since the start of this week I have been experiencing a glitch in the multimedia on my Samsung R518 laptop. I have 2 problems: Videos in every player are speeded up around 2 or 4 times (including youtube.com (both HTML5 and flash variants), any other video on the web and videos on my laptop played by Totem Media Player), exception is VLC player, but 2nd problem does concern even that. There is no sound - simple as that (with or without headphones plugged in). These all problems are now, and has not seen before, I upgraded to Ubuntu 10.10 after it was possible, and from start I didn't have anything from this - it just started in this week. I haven't even putted new software in. I have more or less solved the question (kind of) - I just logged in as a guest - and it all works, but when I make a new user - it does not. Please help me. Some stats below: sudo lshw -c sound *-multimedia description: Audio device product: RV710/730 vendor: ATI Technologies Inc physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:48 memory:cfeec000-cfeeffff *-multimedia description: Audio device product: 82801I (ICH9 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 03 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:47 memory:fc200000-fc203fff sudo lshw -c video *-display description: VGA compatible controller product: M92 LP [Mobility Radeon HD 4300 Series] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:46 memory:d0000000-dfffffff ioport:2000(size=256) memory:cfef0000-cfefffff memory:cfe00000-cfe1ffff

    Read the article

  • Generic Repositories with DI & Data Intensive Controllers

    - by James
    Usually, I consider a large number of parameters as an alarm bell that there may be a design problem somewhere. I am using a Generic Repository for an ASP.NET application and have a Controller with a growing number of parameters. public class GenericRepository<T> : IRepository<T> where T : class { protected DbContext Context { get; set; } protected DbSet<T> DbSet { get; set; } public GenericRepository(DbContext context) { Context = context; DbSet = context.Set<T>(); } ...//methods excluded to keep the question readable } I am using a DI container to pass in the DbContext to the generic repository. So far, this has met my needs and there are no other concrete implmentations of IRepository<T>. However, I had to create a dashboard which uses data from many Entities. There was also a form containing a couple of dropdown lists. Now using the generic repository this makes the parameter requirments grow quickly. The Controller will end up being something like public HomeController(IRepository<EntityOne> entityOneRepository, IRepository<EntityTwo> entityTwoRepository, IRepository<EntityThree> entityThreeRepository, IRepository<EntityFour> entityFourRepository, ILogError logError, ICurrentUser currentUser) { } It has about 6 IRepositories plus a few others to include the required data and the dropdown list options. In my mind this is too many parameters. From a performance point of view, there is only 1 DBContext per request and the DI container will serve the same DbContext to all of the Repositories. From a code standards/readability point of view it's ugly. Is there a better way to handle this situation? Its a real world project with real world time constraints so I will not dwell on it too long, but from a learning perspective it would be good to see how such situations are handled by others.

    Read the article

  • Unable to use Maya animation with scripts when imported to Unity

    - by keshk
    I am testing to import Maya animation over to Unity. I set up a simple cylinder with 2 bones and an IK handle. Made a simple animation where the cylinder bends and goes back to straight position over 24 frames. Following that, I selected everything and baked, all bones,ik,(animation by selecting all at the graph editor) and even the cylinder. I saved the scene and then select all and export as FBX with animation and bake checked. In unity imported it and at the preview able to see the animation. When I load the model into scene and play (after assigning the controller), able to see animation too. But now when I try to script it and control the animation, nothing happens. Even to test, I tried the following under the Update method. if(animation.isPlaying) Debug.Log("Animation Works"); else Debug.Log("Animation not working"); The bool doesn't even return true nor false. My animation is called "bend", thus just for try I did the following and nothing happens. animation.Play("bend"); Can please advice based on my steps, am I missing something. Do I need to add the controller or is that an unnecessary step? Did I screw up on the Maya part or the Unity part. Thanks for help.

    Read the article

  • System speakers not recognized

    - by Kyle Maxwell
    Since upgrading to Xubuntu 13.10, sound has not functioned properly (e.g. screeching when playing Skype notifications). Now, however, it does not function at all. pavucontrol only shows Dummy Output and does not recognize the built-in speakers on my Dell Precision M4600. Possibly related, the sound indicator applet does not come up when I click on it, only showing a small white bar underneath it. I have purged and reinstalled pulseaudio. lspci -v shows: 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) Subsystem: Dell Precision M4600 Flags: bus master, fast devsel, latency 0, IRQ 56 Memory at f2560000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 01:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: Dell Device 14a3 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f0080000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel The "Capabilities: <access denied" line makes me wonder if there's a permissions issue, as the Log Out applet now shows "Restart" and "Shutdown" grayed out. groups shows me in: kmaxwell adm dialout cdrom sudo dip plugdev fuse lpadmin netdev sambashare vboxusers

    Read the article

  • "Enable Wireless" option is disabled in network settings

    - by silenTK
    I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

    Read the article

  • ADF Essentials - Available for free and certified on GlassFish!

    - by delabassee
    If you are an Oracle customer, you are probably familiar with Oracle ADF (Application Development Framework). If you are not, ADF is, in a nutshell, a Java EE based framework that simplifies the development of enterprise applications. It is the development framework that was used, among other things, to build Oracle Fusion Applications. Oracle has just released ADF Essentials, a free to develop and deploy version of Oracle ADF's core technologies. As a good news never come alone, GlassFish 3.1.2 is now a certified container for ADF Essentials! ADF Essentials leverage core ADF features and includes: Oracle ADF Faces - a set of more than 150 JSF 2.0 rich components that simplify the creation of rich Web user interfaces (charting, data vizualization, advanced tables, drag and drop, touch gesture support, extensive windowing capabilities, etc.) Oracle ADF Controller - an extension of the JSF controller that helps build reusable process flows and provides the ability to create dynamic regions within Web pages. Oracle ADF Binding - an XML-based, meta-data abstraction layer to connect user interfaces to business services. Oracle ADF Business Components – a declaratively-configured layer that simplifies developing business services against relational databases by providing reusable components that implement common design patterns. ADF is a highly declarative framework, it has always had a very good tooling support. Visual development for Oracle ADF Essentials is provided in Oracle JDeveloper 11.1.2.3. Eclispe support is planned for a later OEPE (Oracle Enterprise Pack for Eclipse) release. Here are some relevant links to quickly learn on how to use ADF Essentials on GlassFish: Video : Oracle ADF Essentials Overview and Demo Deploying Oracle ADF Essentials Applications to Glassfish OTN : Oracle ADF Essentials Ressources

    Read the article

  • Resolution changes when using switch

    - by Edward D
    So, the "real" resolution of my monitor is 1024x768. That's what I'd use on my docked Windows laptop, and what I'd use on my Xubuntu desktop connected directly. When I connect a switch, to switch between the two, however, the ubuntu machine's resolution changes. Everything's still proportional, and it still thinks it's doing 1024x768, but the icons and fonts appear larger. Not 800x600 larger, but still big. When I used Xubuntu Precise, I created an xorg.conf file to set a resolution of 1280x1024 which made it look the way it does without the switch ... as a workaround. When I upgraded to Trusty, I lost this. I tried to re-create it, but doesn't seem to load my file. Ideally, I'd like to correct the original problem, but I'd settle for being able to up the resolution. I searched for a while, and tried to do it, but I'm giving up ... please help me out. Controller: Intel Corporation 82915G/P/GV/GL/PL/910GL Memory Controller Hub (rev 04) Monitor: NEC MultiSync LCD 1850e http://www.necdisplay.com/documents/UserManuals/LCD1850E_manual.pdf OS: Xubuntu 14.04 Trusty /etc/X11/xorg.conf: # YOU CREATED THIS FILE # sudo leafpad /etc/X11/xorg.conf Section "Device" Identifier "Configured Video Device" EndSection Section "Monitor" Identifier "NEC LCD1850E" # I found Synchronization Range at: # http://www.necdisplay.com/documents/UserManuals/LCD1850E_manual.pdf HorizSync 31.0-82.0 VertRefresh 55.0-85.0 EndSection Section "Screen" Identifier "Default Screen" Monitor "NEC LCD1850E" Device "Configured Video Device" SubSection "Display" Depth 24 Modes "1280x1024" "1280x960" "1024x768" "800x600" "848x480" "640x480" EndSubSection EndSection

    Read the article

  • Displaying a Paged Grid of Data in ASP.NET MVC

    This article demonstrates how to display a paged grid of data in an ASP.NET MVC application and builds upon the work done in two earlier articles: Displaying a Grid of Data in ASP.NET MVC and Sorting a Grid of Data in ASP.NET MVC. Displaying a Grid of Data in ASP.NET MVC started with creating a new ASP.NET MVC application in Visual Studio, then added the Northwind database to the project and showed how to use Microsoft's Linq-to-SQL tool to access data from the database. The article then looked at creating a Controller and View for displaying a list of product information (the Model). Sorting a Grid of Data in ASP.NET MVC enhanced the application by adding a view-specific Model (ProductGridModel) that provided the View with the sorted collection of products to display along with sort-related information, such as the name of the database column the products were sorted by and whether the products were sorted in ascending or descending order. The Sorting a Grid of Data in ASP.NET MVC article also walked through creating a partial view to render the grid's header row so that each column header was a link that, when clicked, sorted the grid by that column. In this article we enhance the view-specific Model (ProductGridModel) to include paging-related information to include the current page being viewed, how many records to show per page, and how many total records are being paged through. Next, we create an action in the Controller that efficiently retrieves the appropriate subset of records to display and then complete the exercise by building a View that displays the subset of records and includes a paging interface that allows the user to step to the next or previous page, or to jump to a particular page number, we create and use a partial view that displays a numeric paging interface Like with its predecessors, this article offers step-by-step instructions and includes a complete, working demo available for download at the end of the article. Read on to learn more! Read More >

    Read the article

  • wireless card not detected

    - by user281219
    i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

    Read the article

  • Restart and/or graphics problem in Ubuntu 12.04

    - by kara
    I having been using 12.04 for a couple of months now, with v. little problems. The other day I restarted my computer, and though I think it rebooted, the screen would be black. I could not even get a visual from a live cd. Finally, I was able to get it to load, but the resolution has been completely off. The computer thinks I have a laptop screen, when I actually have a ViewSonic VP2330wb, and it detects only two resolutions. And still, I have a problem with rebooting. If the screen locks after I leave it for a while, I can't get a visual back, and then when I force a shutdown, it takes 3 times for me to get a grub screen. Then I have to boot in recovery mode, and then finally in normal mode, but the screen is still always off. This is my video card: description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list configuration: latency=0 resources: memory:fe000000-fe3fffff memory:d0000000-dfffffff ioport:f000(size=64) I am a new ubuntu user, and am at my wits end. Any help would be greatly appreciated.

    Read the article

  • Sound card not detected in 13.04

    - by Ganessh Kumar R P
    I have a problem with my sound card. I don't have volume up or down option anywhere. In the setting -> Sound I don't have any card detected. But when I run the command sudo aplay -l, I get the following output **** List of PLAYBACK Hardware Devices **** Failed to create secure directory (/home/ganessh/.config/pulse): Permission denied card 0: MID [HDA Intel MID], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 And the command lspci -v | grep -A7 -i "audio" outputs 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 48 Memory at f0f20000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) (prog-if 00 [Normal decode]) -- 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d3efc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 07:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 So, I assume that the drivers are properly installed but still I don't get any option in the settings or volume control. The same card used to work well back in 2010 versions(04 and 10) Any help is appreciated. Thanks

    Read the article

  • How do I fix the HDMI/DVI display output with Intel HD 4000 Graphics in 12.04?

    - by YumYumYum
    I have an Alienware Dell PC with Intel HD 4000 Graphics (Ivy Bridge) as verified by the output of lspci | grep VGA posted below. 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) The PC only has HDMI and DVI display outputs and using the HDMI output I am only being offered abnormal resolutions. As you can see below it does not even list HDMI1 or DVI1 but just only a fallback. $ export DISPLAY=:0.0 && xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 640 x 480, current 1360 x 768, maximum 1360 x 768 default connected 1360x768+0+0 0mm x 0mm 1360x768 0.0* 1024x768 0.0 800x600 0.0 640x480 0.0 How can I fix this? Does it just need to be configured differently or will I need to use a newer kernel (as Intel Graphics drivers are included in the kernel)? Follow up: kernel to latest Step 1: Go to: http://kernel.ubuntu.com/~kernel-ppa/mainline/ Go to last: http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.6-rc3-quantal/ Download: http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.6-rc3-quantal/linux-headers-3.6.0-030600rc3-generic_3.6.0-030600rc3.201208221735_amd64.deb http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.6-rc3-quantal/linux-headers-3.6.0-030600rc3_3.6.0-030600rc3.201208221735_all.deb http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.6-rc3-quantal/linux-image-3.6.0-030600rc3-generic_3.6.0-030600rc3.201208221735_amd64.deb http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.6-rc3-quantal/linux-image-extra-3.6.0-030600rc3-generic_3.6.0-030600rc3.201208221735_amd64.deb Step 2: sudo dpkg -i linux*.deb Step 3: reboot which shows that i have Ubuntu 12.04 with latest $ uname -a Linux sun-Alienware-X51 3.6.0-030600rc3-generic #201208221735 SMP Wed Aug 22 21:36:32 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux But still same problem remain.

    Read the article

  • External display resolution issue

    - by Steven
    I'm new to Ubuntu. I've 'dabbled' in the past but Windows was annoying me too much so I finally made the change. One thing I use my laptop for is outputting the screen onto an external monitor. In Windows this usually works fine (but when there is an issue, it's a pain to resolve and has crashed my computer on many occasions). In Ubuntu it's a very simple case of "plug and play" because it displays the content immediately with no major problems. However, I can only alter the resolution of the external display to 4:3 formats, whereas the external monitor is 16:9, so the picture is stretched. In Windows there's loads of resolutions to choose from. If I disable the laptop's screen, it still doesn't allow me to display the correct resolution externally (on VGA). Further to that, if I close the laptop it keeps the external screen as it is, but when I reopen the laptop, the laptop screen doesn't turn back on until I restart. If it's a video I am watching, I can use VLC to alter the aspect ratio so the video looks fine, but it's quite an annoying work around. I used terminal to find my graphics controller, which is "Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07)" (not great, I know... the laptop was a free gift with my mobile!) Any idea of how I can get the resolution on the external monitor to be correct?

    Read the article

  • How to do MVC the right way

    - by Ieyasu Sawada
    I've been doing MVC for a few months now using the CodeIgniter framework in PHP but I still don't know if I'm really doing things right. What I currently do is: Model - this is where I put database queries (select, insert, update, delete). Here's a sample from one of the models that I have: function register_user($user_login, $user_profile, $department, $role) { $department_id = $this->get_department_id($department); $role_id = $this->get_role_id($role); array_push($user_login, $department_id, $role_id); $this->db->query("INSERT INTO tbl_users SET username=?, hashed_password=?, salt=?, department_id=?, role_id=?", $user_login); $user_id = $this->db->insert_id(); array_push($user_profile, $user_id); $this->db->query(" INSERT INTO tbl_userprofile SET firstname=?, midname=?, lastname=?, user_id=? ", $user_profile); } Controller - talks to the model, calls up the methods in the model which queries the database, supplies the data which the views will display(success alerts, error alerts, data from database), inherits a parent controller which checks if user is logged in. Here's a sample: function create_user(){ $this->load->helper('encryption/Bcrypt'); $bcrypt = new Bcrypt(15); $user_data = array( 'username' => 'Username', 'firstname' => 'Firstname', 'middlename' => 'Middlename', 'lastname' => 'Lastname', 'password' => 'Password', 'department' => 'Department', 'role' => 'Role' ); foreach ($user_data as $key => $value) { $this->form_validation->set_rules($key, $value, 'required|trim'); } if ($this->form_validation->run() == FALSE) { $departments = $this->user_model->list_departments(); $it_roles = $this->user_model->list_roles(1); $tc_roles = $this->user_model->list_roles(2); $assessor_roles = $this->user_model->list_roles(3); $data['data'] = array('departments' => $departments, 'it_roles' => $it_roles, 'tc_roles' => $tc_roles, 'assessor_roles' => $assessor_roles); $data['content'] = 'admin/create_user'; parent::error_alert(); $this->load->view($this->_at, $data); } else { $username = $this->input->post('username'); $salt = $bcrypt->getSalt(); $hashed_password = $bcrypt->hash($this->input->post('password'), $salt); $fname = $this->input->post('firstname'); $mname = $this->input->post('middlename'); $lname = $this->input->post('lastname'); $department = $this->input->post('department'); $role = $this->input->post('role'); $user_login = array($username, $hashed_password, $salt); $user_profile = array($fname, $mname, $lname); $this->user_model->register_user($user_login, $user_profile, $department, $role); $data['content'] = 'admin/view_user'; parent::success_alert(4, 'User Sucessfully Registered!', 'You may now login using your account'); $data['data'] = array('username' => $username, 'fname' => $fname, 'mname' => $mname, 'lname' => $lname, 'department' => $department, 'role' => $role); $this->load->view($this->_at, $data); } } Views - this is where I put html, css, and JavaScript code (form validation code for the current form, looping through the data supplied by controller, a few if statements to hide and show things depending on the data supplied by the controller). <!--User registration form--> <form class="well min-form" method="post"> <div class="form-heading"> <h3>User Registration</h3> </div> <label for="username">Username</label> <input type="text" id="username" name="username" class="span3" autofocus> <label for="password">Password</label> <input type="password" id="password" name="password" class="span3"> <label for="firstname">First name</label> <input type="text" id="firstname" name="firstname" class="span3"> <label for="middlename">Middle name</label> <input type="text" id="middlename" name="middlename" class="span3"> <label for="lastname">Last name</label> <input type="text" id="lastname" name="lastname" class="span3"> <label for="department">Department</label> <input type="text" id="department" name="department" class="span3" list="list_departments"> <datalist id="list_departments"> <?php foreach ($data['departments'] as $row) { ?> <option data-id="<?php echo $row['department_id']; ?>" value="<?php echo $row['department']; ?>"><?php echo $row['department']; ?></option> <?php } ?> </datalist> <label for="role">Role</label> <input type="text" id="role" name="role" class="span3" list=""> <datalist id="list_it"> <?php foreach ($data['it_roles'] as $row) { ?> <option data-id="<?php echo $row['role_id']; ?>" value="<?php echo $row['role']; ?>"><?php echo $row['role']; ?></option> <?php } ?> </datalist> <datalist id="list_collection"> <?php foreach ($data['tc_roles'] as $row) { ?> <option data-id="<?php echo $row['role_id']; ?>" value="<?php echo $row['role']; ?>"><?php echo $row['role']; ?></option> <?php } ?> </datalist> <datalist id="list_assessor"> <?php foreach ($data['assessor_roles'] as $row) { ?> <option data-id="<?php echo $row['role_id']; ?>" value="<?php echo $row['role']; ?>"><?php echo $row['role']; ?></option> <?php } ?> </datalist> <p> <button type="submit" class="btn btn-success">Create User</button> </p> </form> <script> var departments = []; var roles = []; $('#list_departments option').each(function(i){ departments[i] = $(this).val(); }); $('#list_it option').each(function(i){ roles[roles.length + 1] = $(this).val(); }); $('#list_collection option').each(function(i){ roles[roles.length + 1] = $(this).val(); }); $('#list_assessor option').each(function(i){ roles[roles.length + 1] = $(this).val(); }); $('#department').blur(function(){ var department = $.trim($(this).val()); $('#role').attr('list', 'list_' + department); }); var password = new LiveValidation('password'); password.add(Validate.Presence); password.add(Validate.Length, {minimum: 10}); $('input[type=text]').each(function(i){ var field_id = $(this).attr('id'); var field = new LiveValidation(field_id); field.add(Validate.Presence); if(field_id == 'department'){ field.add(Validate.Inclusion, {within : departments}); } else if(field_id == 'role'){ field.add(Validate.Inclusion, {within : roles}) } }); </script> The codes above are actually code from the application that I'm currently working on. I'm working on it alone so I don't really have someone to review my code for me and point out the wrong things in it so I'm posting it here in hopes that someone could point out the wrong things that I've done in here. I'm also looking for some guidelines in writing MVC code like what are the things that should be and shouldn't be included in views, models and controllers. How else can I improve the current code that I have right now. I've written some really terrible code before(duplication of logic, etc.) that's why I want to improve my code so that I can easily maintain it in the future. Thanks!

    Read the article

  • ASP.NET MVVM Handling multiple Data Transfer Objects on a single page

    - by meffect
    I have an asp.net mvc "edit" page which allows the user to make edits to the parent entity, and then also "create" child entities on the same page. Note: I'm making these data transfer objects up. public class CustomerViewModel { public int Id { get; set; } public Byte[] Timestamp { get; set; } public string CustomerName { get; set; } public etc.. public CustomerOrderCreateViewModel CustomerOrderCreateViewModel { get; set; } } In my view I have two html form's. One for Customer "edit" Http Posts, and the other for CustomerOrder "create" Http Posts. In the view page, I load the CustomerOrder "create" form in using: <div id="CustomerOrderCreate"> @Html.Partial("Vendor/_CustomerOrderCreatePartial", Model.CustomerOrderCreateViewModel) </div> The CustomerOrder html form action posts to a different controller HttpPost ActionResult than the Customer "edit" Action Result. My concern is this, on the CustomerOrder controller, in the HttpPost ActionResult [HttpPost] public ActionResult Create(CustomerOrderCreateViewModel vm) { if (!ModelState.IsValid) { return [What Do I Return Here] } ...[Persist to database code]... } I don't know what to return if the model state isn't valid. Right now it's not a problem, because jquery unobtrusive validation handles validation on the client. But what if I need more complex validation (ie: the server needs to handle the validation).

    Read the article

  • Intel N10 graphics

    - by Rapsag1980
    Español: Buen día. Instalé en una notebook ubuntu 12.04 pero me da el problema que solamente me da dos resoluciones de pantallas 800x600 y 1024x768... En la primera se ve muy grotesca la pantalla y en la segunda se ve bien, pero falta un pedazo de pantalla arriba y abajo... He tratado de buscar información sobre el tema pero parece uno de esos "bugs" que no han conseguido ser erradicados... Intenté hacer el Xorg.conf y esas cosas y nomas no se puede... Recurro a su sapiencia y experiencia en este tipo de problemas... La mini es una Lanix Neuron lt, procesador intel atom n450 y la tarjeta Intel corporation N10 family integrated graphics controller.... Inglés: Good day. I installed ubuntu 12.04 on a notebook but I get the problem that only gives me two screen resolutions of 800x600 and 1024x768 ... The first screen looks very grotesque and the second looks good, but missing a piece of screen up and down ... I tried to find information on the subject but it seems one of those "bugs" that have failed to be eradicated ... I tried to do the Xorg.conf nomas and stuff and you can not ... I appeal to your wisdom and experience in this kind of problem ... The mini is a Neuron Lanix lt, Intel Atom N450 processor and the Intel integrated graphics family corporation N10 controller ....

    Read the article

  • Broadcom Wireless Issues in Lubuntu 14.04

    - by ratxinxaxcage67
    I recently installed Lubuntu 14.04 on my parents' old laptop, and I've been having a super difficult time getting the Broadcom card up and running. I've been following this thread: Installing Broadcom Wireless Drivers ...but I'm still stuck. lspci -vnn | grep Network showed: 06:05.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 02) iwconfig showed: lo no wireless extensions. eth0 no wireless extensions. I've installed b43-firmware-installer and b43-fwcutter and also the linux-firmware-nonfree package. At boot, I keep getting a b43-phy0 error, so I tried sudo rmmod b43, and I got: rmmod: ERROR: Module b43 is not currently loaded I also tried: dmesg | grep b43 [ 17.318405] b43legacy-phy0: Broadcom 4306 WLAN found (core revision 4) [ 17.384870] b43legacy-phy0: Loading firmware b43legacy/ucode4.fw [ 18.046777] b43legacy ssb0:0: Direct firmware load failed with error -2 [ 18.046785] b43legacy ssb0:0: Falling back to user helper [ 18.047858] b43legacy-phy0 ERROR: Firmware file "b43legacy/ucode4.fw" not found or load failed. [ 18.047965] b43legacy-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 3). I went to url it told me to, but it didn't tell me to do anything I haven't already tried. Any help and/or suggestions would be greatly appreciated!

    Read the article

  • How can I get my first-person character in Unity to move to a ledge with an animation?

    - by BallzOfSteel
    I'm trying to get this to happen: The character walks up to a large crate, the player presses a button, and an animation starts playing where the character climbs up on to the crate. (all in first person view). So far I tried this with normal "First Person Controller" Prefab in Unity. My code so far: function OnTriggerStay(other : Collider){ if(other.tag == "GrabZone"){ if(Input.GetKeyDown("e")){ animation.Play("JumpToLedge"); } } } However when i use this on The FPC it will always play from the position the animation is created on. I also tried to create an empty game object, placing the FPC in there. Gives same effect. I also tried just animating the graphics of the FPC alone. This seems to work but since the Character Controller itself is not animated that stays onthe ground. So the whole FPC wont work anymore. Is there anyway i could let this animation play on the local position the player is on at that time? Or can you think of any other logical solution for a grab and climb?

    Read the article

  • Dim (NEARLY blank) laptop screen, secondary screen works - why?

    - by LIttle Ancient Forest Kami
    My laptop screen is (almost) black while my secondary screen is fine. I believe it to be backlight / brightness related. Problem description it starts when I start the laptop system loads and works fine, just screen has problems I can see the screen though very faintly / dimly - it's hard to see anything which ain't very white e.g. starting screen has big Thinkpad logo in white, large font - I can see it, though very dimly second screen works very well Official backligtht debugging: using acpi setting as prescribed there for Thinkpads didn't help I can see an entry in /sys/class/backlight/ and it changes when I press hotkeys for brightness (current backlight power for instance goes up or down) acpi-off didn't helpm neither did acpi_backlight=vendor Hardware data Laptop is Thinkpad Edge with glossy screen. 4 processors, 2 cores, exemplary CPU data from cat /proc/cpuinfo reports Genuine Intel i5 (M 480 @ 2.67GHz). OS is Ubuntu Lucid, 10.04 LTS, 64-bit, with Linux generic kernel (2.6.32-44) and GNOME 2.32.2 (though I doubt there lies the problem). $ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc M92 [Mobility Radeon HD 4500 Series] $ lshw -C display *-display description: VGA compatible controller product: M92 [Mobility Radeon HD 4500 Series] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:33 memory:c0000000-dfffffff(prefetchable) ioport:2000(size=256) memory:f0300000-f030ffff memory:f0320000-f033ffff(prefetchable) Driver I was NOT running any proprietary drivers, just checked with "Hardware drivers". There is one for ATI that is suggested there, though I didn't need it so far. UPDATE: changing the driver to proprietary one (ATI/AMD FGLRX) didn't help. Tried and failed Resetting / running on power or battery / charging / getting rid of static electricity / warming up *doesn't help* This is NOT a blank-screen problem, at least it isn't following official Ubuntu black-screen diagnostics - I can see my screen, though barely. What I will try next: - check last updates I've made - IIRC I am running on nomodeset already, but will verify this Any ideas how to proceed best? What is most probable cause?

    Read the article

  • AR242x / AR542x wireless card not working

    - by Pipan87
    My wifi worked perfect until I updated to the latest version of Ubuntu. Now I don't find any wireless connections at all. I have tried lots of guides on the internet but I can't get it to work. I did however start to work once after writing something I don't remember in Terminal, but after rebooting it stopped working again. Some info (don't know if you need more to help): 01:00.0 Ethernet controller: Atheros Communications AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0) Subsystem: Acer Incorporated [ALI] Device 022c Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at 55200000 (64-bit, non-prefetchable) [size=256K] I/O ports at 3000 [size=128] Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [58] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [180] Device Serial Number ff-93-2e-de-00-23-8b-ff Kernel driver in use: ATL1E Kernel modules: atl1e 02:00.0 Ethernet controller: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Foxconn International, Inc. Device e00d Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at 54100000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Kernel driver in use: ath5k Kernel modules: ath5k

    Read the article

  • Driver for asus wireless PC card WL-100GE

    - by emab
    I have bought an Asus wireless LAN PC Card WL-100GE model, and I am using lubuntu on my system. While I have no cable connection, currently I cannot access the internet and update my laptop. Device: Broad Range Wireless Card Bus Adaptor - Asus - WL-100GE I searched the web and couldn't find any adequate driver for it. Is there any solution for it? My sudo lshw -C network output is: *-network description: Ethernet interface product: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:02:3f:ba:55:c8 size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=128 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:3000(size=256) memory:e0200800-e02008ff *-network description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:07:00.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:21 memory:38000000-38001fff ----:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions.

    Read the article

  • How to disable discrete GPU using NVIDIA drivers?

    - by penzoiders
    I have a DELL studio XPS 13 (aka 1340) as of 12.04 most things run smoothly out of the box, but I have some power draining and warmness issues (if not to be called terrible heat issues) The system came with a NVIDIA GeForce 9500M (which has Hybrid SLI) and it shows up in "lspci" as these 2 cards 02:00.0 VGA compatible controller: NVIDIA Corporation G98 [GeForce 9200M GS] (rev a1) 03:00.0 VGA compatible controller: NVIDIA Corporation C79 [GeForce 9400M G] (rev b1) I had to install nvidia-current over noveau driver 'cause noveau does freeze the system after suspension. By installing nvidia-current and running nvidia-xconfig the resume process after suspension is fixed. By the way both with nvidia-current and noveau the system drains a lot of battery and heats up a lot. I suppose this is because the discrete GPU is always on. I don't really need 3D graphics on this system, if not the minimal to run unity and compiz for window management. So my question is: How do I disable, using nvidia-current, the discrete GPU 9200M and use only the integrated one 9400M? notes: In BIOS I have no option to disable discrete GPU This I think is not applicable because of the suspension-freeze issue (with noveau): https://help.ubuntu.com/community/HybridGraphics I've found this but I don't know which --sli option I should choose to fit my needs: http://manpages.ubuntu.com/manpages/hardy/man1/nvidia-xconfig.1.html My system has not optimus or cuda, but anyone can tell me if bumblebee can work for me?

    Read the article

  • Multi-screen and Nvidia GT220

    - by Bohors
    Excuse me first for my broken English I have 3 monitors on two Nvidia GT220. Unity 2D works fine after using the proprietary drivers. But no way to use compiz effects. I'm on Ubuntu 11.10 (I also tested for curiosity 12.04 for the same result) I noticed in the "System Settings" / "details" that my graphics card is not recognized (graphics card "unknown") and "View" only returns me my first screen (with the correct resolution) also in unknown. $ lspci | grep VGA 01:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 220] (rev a2) 05:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 220] (rev a2) xorg.conf : Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" Below "Screen0" Screen 2 "Screen2" RightOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "1" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "Acer V243HL" HorizSync 30.0 - 80.0 VertRefresh 55.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "LG Electronics L1920P" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor2" VendorName "Unknown" ModelName "Acer V243HL" HorizSync 30.0 - 80.0 VertRefresh 55.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 220" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 220" BusID "PCI:5:0:0" Screen 0 EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 220" BusID "PCI:5:0:0" Screen 1 EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "0" Option "TwinViewXineramaInfoOrder" "DFP-0" Option "metamodes" "1920x1080_60_0 +0+0; nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "CRT: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "DFP: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Disable" EndSection Have you any idea? thanks

    Read the article

< Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >