Search Results

Search found 22903 results on 917 pages for 'network namespace'.

Page 154/917 | < Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >

• Basic multicast network performance problems

  - by davedavedave

  I've been using mpong from 29west's mtools package to get some basic idea of multicast latency across various Cisco switches: 1Gb 2960G, 10Gb 4900M and 10Gb Nexus N5548P. The 1Gb is just for comparison. I have the following results for ~400 runs of mpong on each switch (sending 65536 "ping"-like messages to a receiver which then sends back -- all over multicast). Numbers are latencies measured in microseconds. Switch Average StdDev Min Max 2960 (1Gb) 109.68463 0.092816 109.4328 109.9464 4900M (10Gb) 705.52359 1.607976 703.7693 722.1514 NX 5548(10Gb) 58.563774 0.328242 57.77603 59.32207 The result for 4900M is very surprising. I've tried unicast ping and I see the 4900 has ~10us higher latency than the N5548P (average 73us vs 64us). Iperf (with no attempt to tune it) shows both 10Gb switches give me 9.4Gbps line speed. The two machines are connected to the same switch and we're not doing any multicast routing. OS is RHEL 6. 10Gb NICs are HP 10GbE PCI-E G2 Dual-port NICs (I believe they are rebranded Mellanox cards). The 4900 switch is used in a project with tight access control so I'm waiting for approval before I can access it and check the config. The other two I have full access to configure. I've looked at the Cisco document[2] detailing differences between NX-OS and IOS w.r.t multicast so I've got some ideas to try out but this isn't an area where I have much expertise. Does anyone have any idea what I should be looking at once I get access to the switch? [1] http://docwiki.cisco.com/wiki/Cisco_NX-OS/IOS_Multicast_Comparison

  Read the article

• How do I install Redhat Enterprise Linux 5 on PPC from the network

  - by Dave Roger

  I want to be able to install rhel5 on ppc using yaboot the same as PXE for other platforms. How do I do it?

  Read the article

• IPs on home network

  - by windchime

  I have a Linksys router and a Belkin wireless router at home. The Linksys router is connected to cable modem and two computers, as well as to the Belkin wireless router. A 3rd computer is connected to the Belkin router through Wifi. The IP addresses of the computers connected to Linksys are 192.168.1.101 and 192.168.1.102. The IP address of the Linksys router on LAN is 192.168.1.1. The IP address of the Belkin wireless router is 192.168.2.1(based on the 3rd computer's routing table) and the IP address of the 3rd computer is 192.168.2.5. If I ping 192.168.1.101 from 192.168.2.5, all are well. However, if I ping 192.168.2.5 from 192.168.1.101, Destination Host Unreachable. Why?

  Read the article

• Install ubuntu 9.10 over network

  - by Narendra Sisodiya

  Imagine the condition for lab for 100 computers Case 1 - Hardware conf of all 100 comp is same -- what is the best way to install Ubuntu 9.10 in whole lab Case 2 - Hardware conf of all 100 comp is different from each other -- what is the best way to install Ubuntu 9.10 in whole lab Any practical experience ? Any good links ?

  Read the article

• Slow Citrix connection related to mapped network drives

  - by George

  I have this weird issue with Citrix being slow and maybe users just being a little dramatic, but I am curious as to why that happens. Let me give you a little bit of a background. Citrix is running off of Windows 2003 server, TSprofiles and file server were located on the same server, until recently. We have moved our file server over to a new server with tons of space. We have Citrix on one server, TSprofiles on another and file server on third. We are using logon scripts to map home drives, shared drive and etc. Now, up until we made the file server move, the logon process took several seconds and most users couldn't even notice logon script being executed as they logon. Now, it takes upwards of several minutes and users can see logon script being executed at a slow pace, one line at a time. The only new variable in this whole scenario is the new file server. All the servers are physically located in the same location and on the same subnet. So, I guess my question is, if anyone can explain why a sudden sluggishness? And any tools I can use to troubleshoot the issue? Thanks!

  Read the article

• Yet another "can't connect to MySQL over the network" question - but i seriously tried everything

  - by mireille raad

  Hello, I was left with the easy task of installing moodle. I am VPNing to 2 servers, one for the database and the other apache/php server 1 must connect over LAN to the mySQL db on server 2 I added a user with following priveleges : +---------------+------------+ | host | user | +---------------+------------+ | % | mir | | 10.10.40.15 | mir | | x.x.x.x | mir | | localhost | mir | Disabled firewall temporary made sure that my username/password combinations are correct, flushed priveleges, restarted mysqld i wnt to /etc/my.cnf .. if i try to add the port=3306 bind-address=10.10.40.15 or anything that is different from 0.0.0.0 or 127.0.0.1 - mysql wouldn't restart i read and tried many forums and pages and asked friends for tips but nothing works So my question to you : are there any networking extensions that need to be installed for mysql, how do i know nothing is missing from the installation any troubleshooting tips, any idea how to fix this, any step by step check list, am i missing something simple/stupid, please anything that comes to mind, let me know Appreciate your feedback on this friday night stuck at work :P

  Read the article

• There's a black hole in my server (TcpClient, TcpListener)

  - by Matías

  Hi, I'm trying to build a server that will receive files sent by clients over a network. If the client decides to send one file at a time, there's no problem, I get the file as I expected, but if it tries to send more than one I only get the first one. Here's the server code: I'm using one Thread per connected client public void ProcessClients() { while (IsListening) { ClientHandler clientHandler = new ClientHandler(listener.AcceptTcpClient()); Thread thread = new Thread(new ThreadStart(clientHandler.Process)); thread.Start(); } } The following code is part of ClientHandler class public void Process() { while (client.Connected) { using (MemoryStream memStream = new MemoryStream()) { int read; while ((read = client.GetStream().Read(buffer, 0, buffer.Length)) > 0) { memStream.Write(buffer, 0, read); } if (memStream.Length > 0) { Packet receivedPacket = (Packet)Tools.Deserialize(memStream.ToArray()); File.WriteAllBytes(Path.Combine(Environment.GetFolderPath(Environment.SpecialFolder.DesktopDirectory), Guid.NewGuid() + receivedPacket.Filename), receivedPacket.Content); } } } } On the first iteration I get the first file sent, but after it I don't get anything. I've tried using a Thread.Sleep(1000) at the end of every iteration without any luck. On the other side I have this code (for clients) . . client.Connect(); foreach (var oneFilename in fileList) client.Upload(oneFilename); client.Disconnect(); . . The method Upload: public void Upload(string filename) { FileInfo fileInfo = new FileInfo(filename); Packet packet = new Packet() { Filename = fileInfo.Name, Content = File.ReadAllBytes(filename) }; byte[] serializedPacket = Tools.Serialize(packet); netStream.Write(serializedPacket, 0, serializedPacket.Length); netStream.Flush(); } netStream (NetworkStream) is opened on Connect method, and closed on Disconnect. Where's the black hole? Can I send multiple objects as I'm trying to do? Thanks for your time.

  Read the article

• Network Printers

  - by Jack

  We have a sever that shares all the printers. The PC's that are running on XP professional get a error message quoting (Connect to Printer). The only way I can find to get around the problem is by restating the printer and as soon is it comes online you can then add it but you have not got long. do you think it could be anything to-do with updates on the sever? the sever system is running Windows Server 2003 any help would be much appreciated. Thanks

  Read the article

• Vmware sphere setting up external network

  - by Tom Beech

  I've just setup vmware vsphere 5 on a remote server (rented dedicated server). I've added my first VPS (centos 5.8) barebones. It's not finding any IP (internal or external) on boot. I've had an extra external IP assigned to my server that I wanted to use on the VPS. I tried editing the eth0 config and adding the IP in there and turning off the DHCP, but it can't find any IP or ping google or do any networking type things. How do I route the IP to my VPS so I can access it remotely?

  Read the article

• How can I share a printer and files on a Windows network over wifi

  - by Jacques

  What is the easiest way to create this setup: WiFi internet router separate in one room. Study room: Laptop with USB printer connected with wifi. My room: Laptop connected with wifi. I want to be able to print from the "My room" laptop to the "Study room" printer, and also share files between them. What is the easiest way to do this? Note, the wireless router needs to be in a separate room for both laptops to be able to connect to it. I've tried configuring homegroups and stuff to do with IP addresses that I found on the internet but have had no success. I'm not an expert with PC's but I've tried hard so there is probably just some trick to do it. If someone can help that will be great.

  Read the article

• SOHO Netflix and network security

  - by TW

  I want to use WIFI for HiDef video, but I don't trust it for my office PC's. I've heard of VLANs but I have no idea how to set it up or what (SOHO) hardware to buy. Other than getting 2 different DSL lines, how can I be absolutely sure that the PC side doesn't get hacked? What if I want to use MS Home server as a backup device for both sides? Can I make it "read only" for the PC side, and physically change the cable if I need to restore? TW

  Read the article

• Federated access to desktop and network resources in MS AD domains

  - by Glenn Stauffer

  We are looking for a way to provide members of three loosely connected organizations with access to authenticated resources such as file shares, printers, and lab computers. I've seen federation facilities for web resources; is ther something similar for domain logins? Our Active directory domains are not connected so we would have to use email addresses for the username to insure uniqueness. Is there any openid like mechanism that works for AD logins?

  Read the article

• Monitoring Maximum Process Network Activity

  - by user125973

  We have a collocated server on which we run some OpenVZ hosts. Recently, we have had to pay a lot extra we keep exceeding our bandwidth quota. Our quota is 5 Mb/s but we have spike to almost 50. I looked at the graphs and there are some spikes happening at some intervals. I want to know which process is causing this so I need a tool that monitors the processes and gives me the one with the maximum instant traffic (It doesn't matter how much traffic we have as long as we don't exceed the 5Mb/s quota). Does anyone have a recommendation for this? My hosts are CentOS 5 with OpenVZ so I can see all the containter processes from the host, if that helps in any way.

  Read the article

• Get network speed from system files on Linux

  - by Gregory Z

  At which files should I look to check the download/upload speed? I remember doing so a long time ago.

  Read the article

• OS specific network delay, why?

  - by Atilla Filiz

  Since my new ISP installed their own router to my house(I rented a room in a student house so don't have much control on these), I started having strange delays. Any outgoing connection I do, be it http or ssh, is delayed for several seconds, and once it is established, I have no further problems. I open several simultaneous tabs in my browser and after about 5 to 8 seconds, they all connect and load simultaneously and quiet fast. I can actually play online games once I connect.What's more interesting is, I experience this only with Linux distros, namely Arch and some versions of Ubuntu. Access with Windows installs are quiet normal. What might be wrong with my router? Everything was fine with my old router but I have to use this one now.

  Read the article

• Windows 7 network performance tuning for LAN

  - by Hubert Kario

  I want to tune Windows 7 TCP stack for speed in a LAN environment. Bit of background info: I've got a Citrix XenServer set up with Windows 2008R2, Windows 7 and Debian Lenny with Citrix kernel, Windows machines have Tools installed the iperf server process is running on different host, also Debian Lenny. The servers are otherwise idle, tests were repeated few times to confirm results. While testing with iperf 2008R2 can achieve around 600-700Mbps with no tuning what so ever but I can't find any guide or set of parameters that will make Windows 7 achieve anything over 150Mbps with no change in TCP window size using -w parameter to iperf. I tried using netsh autotuining to disabled, experimental, normal and highlyrestricted - no change. Changing congestionprovider doesn't do anything, just as rss and chimney. Setting all the available settings to same values as on Windows 2008R2 host doesn't help. To summarize: Windows 2008R2 default settings: 600-700Mbps Debian, default settings: 600Mbps Windows 7 default settings: 120Mbps Windows 7 default, iperf -w 65536: 400-500Mbps While the missing 400Mbps in performance I blame on crappy Realtek NIC in the XenServer host (I can do ~980Mbps from my laptop to the iperf server) it doesn't explain why Windows 7 can't achieve good performance without manually tuning window size at the application level. So, how to tune Windows 7?

  Read the article

• Cannot connect to xdebug over virtual network - Vagrant Virtualbox

  - by smix96

  I'm trying to set up a development box using Virtualbox / Vagrant / Puppet with the intention of eventually provisioning all my machines up to production. However this is stopping me going forward at the moment. I've installed ubuntu lucid over windows 7. When trying to connect to xdebug by starting a debugging session in eclipse, it hangs at 57% (common in eclipse when it cannot communicate with xdebug). Here is my xdebug.ini and the settings here are appearing in phpinfo(). xdebug.remote_enable=On xdebug.remote_handler=dbgp xdebug.remote_host=192.168.56.1 xdebug.remote_port=9000 I'm now wondering if it's an issue with port forwarding? If eclipse is looking on port 9000, will it find port 9000 on a virtual machine? Any help would be greatly appreciated!

  Read the article

• AIX network parameters to close TCP sockets of unplugged devices

  - by ADD Geek

  Hi there We have an AIX box, running what we call in banking "ATM Switch" not the ATM networking switch, but the bank ATM driver. where we have some ATM machines connected to two server processes. The problem is, when we disconnect any of these machines, the netstat -na| grep <port number> command shows that the socket established for this disconnected device is still established, we have to manually send a command from the software to make the socket aware that it is not live anymore. Is there a parameter on tcp level to make this connection aware within a minute or two that this device is not connected anymore? we had the following parameters set with root privileges: no -o tcp_keepidle=1000 no -o tcp_keepcnt=2 no -o tcp_keepintvl=150 no -o tcp_finwait2=100 it was originally having the default values. but even after we changed these parameters and restarted the server processes, the problem was still there.

  Read the article

• Can't perform ODBC connection to MySQL server on local network

  - by Emmanuel

  I have a wamp server running on LAN ip address 192.168.1.101 . From the browser on my PC which is on the LAN I can access the webserver and have as well set the phpmyadmin.conf file to be able to access the phpmyadmin interface. This works smoothly. On the wamp server I have a database which I'd need to access from any PC on the LAN using the MySQL Connector/ODBC. The problem is that I do not manage to setup the connection correctly. Here are the paramenters I use: Data Source Name: test_connection Description: test conenction Server: 192.168.1.101 Port: 3306 User: root Password: Database: The error message I get is the following: Connection Failed: [HY000][MySQL][ODBC 5.1 Driver]Can's connect to MySql server on '192.168.1.101' (10060) Would anybody have a hint to set up correctly the connection?

  Read the article

• General-purpose unix-based network authentication tool?

  - by Patrick Collison

  I want something that'll integrate auth across SSH, web (ideally including SSL, with the option of authenticating with either client-side cert or password, like they do at MIT), and whatever applications want to use it. Kerberos seems to best fit what I want, but tool support seems surprisingly poor. What do people use these days?

  Read the article

• App to log network user's file activities

  - by Luke

  My employer recently purchased a Mac Pro server (2011 model) and we've installed OSX Lion Server from the Mac Appstore. I'm definitely no server admin, but I have been tasked with finding out the following: Can we monitor or log what users do? (ie, open a file, copy a file.... or file-related tasks) Can we stop files from being copied? Or be alerted when this does occur? Thanks in advance for any assistance.

  Read the article

• IIS 401.3 - Unauthorized on only 1 server out of 3 set up for network load balancing

  - by Tony

  Over the weekend our Server Admin set up two virtual Windows 2008 machines with IIS installed and set them up under NLB. I came in and changed the application pool the website was running under to our domain account that has proper access to the database and the file share hosting our .NET web application Sitefinity, and changed it to .NET 4 Integrated. NLB and everything was running fine on both servers. He brought up the third server for our cluster on Tuesday and I performed the same actions.. The only difference was that I was given admin rights for the third server so I could set it up remotely instead of going to his office. He has full control over the share and NTFS perms on \\hostname\Sitefinity and I believe I only had read access. I pointed the web site to the same \\hostname\Sitefinity\sitename share that the others were on and the authentication/authorization test settings passed. I hit the site from http://localhost (like I did successfully from the other two before trying the cluster's IP address) and I received a HTTP Error 401.3 - Unauthorized. I've verified many times that the application pool is running under the same service account. I tried hitting just a simple test.htm.. works fine on both of the first two servers but I get the same 401.3 on the third. I copied my dev project to the local inetpub directory and re-pointed the website and that ran perfectly. I turned on Failed Request Tracing and it acts like it's still running the local IUSR account I guess (instead of my domain account)? Here is an excerpt of the File Cache Access Start and the error from the trace: FileName \\hostname\sitefinity\sitename\test.htm UserName IUSR DomainName NT AUTHORITY ---------- Successful false FileFromCache false FileAddedToCache false FileDirmoned true LastModCheckErrorIgnored true ErrorCode 2147942405 LastModifiedTime ErrorCode Access is denied. (0x80070005) ---------- ModuleName IIS Web Core Notification 2 HttpStatus 401 HttpReason Unauthorized HttpSubStatus 3 ErrorCode 2147942405 ConfigExceptionInfo Notification AUTHENTICATE_REQUEST ErrorCode Access is denied. (0x80070005) ---------- My personal AD account was then granted read/write perms to the share so I created a new application pool and set the site under it in case there was an issue with the application pool but no success. I created another under my own account and it still failed. It just seems like maybe it's not trying to access the files under the account my application pools are running under although that's the only way I've done things before. I set the Physicial Path Credentials in Advanced Settings on the site to the service account and it threw a 500 error of some sort so I assume that's not the answer (and I don't have to do it on the other servers). It's like somehow I'm trying to force impersonation on the IUSR account or something?

  Read the article

• Get IP network range after reverse DNS?

  - by Max

  For analytics purposes, I'm looking at large sets of IP addresses in server log files. I'm trying to perform reverse-DNS lookups to understand where traffic is coming from - e.g. what percentage of IPs resolve to corporations, schools, government, international etc. Despite a bunch of optimizations, individually reverse-DNS'ing every IP address still appears to be fairly expensive though. So - is there any way to obtain an entire range of IPs from a reverse-DNS? If yes, this could greatly reduce the number of actual reverse-DNS lookups. Example (numbers slightly obfuscated): Log file contains a request from an IP 128.151.162.17 Reverse DNS resolves to 11.142.152.128.in-addr.arpa 21599 IN PTR alamo.ceas.rochester.edu (So this is a visitor from Rochester University, rochester.edu) Now, would it be safe to assume that all at least all IPs from 128.151.162.* will also resolve to rochester.edu? What about 128.151.*.*? Is there a way to get the exact IP range?

  Read the article

• Very long DNS lookups inside my network

  - by Nuno Cordeiro

  Ever since I installed DD-WRT (v24-sp2 08/07/10 std-usb-ftp) on my router (RT-N16), my browsing got substantially slower. Using FirePHP I figured out that it's being caused by VERY long DNS lookups (~30 seconds). When the domain name was very recently accessed then speed is very good. I tried changing DNS on the computer and I tried messing around with the options on DD-WRT. I have tried to configure the router with Google DNS and/or OpenDNS. My current DNS output after using ipconfig -all is: 192.168.1.1 208.67.220.220 8.8.8.8 208.67.222.222 Can someone help me debug and solve this problem? I'd like to snoop the requests themselves. How can I know which DNS requests are being sent and which are failing/succeeding? Note: I don't expect this to be relevant but my router is connected to the internet through an ONT.

  Read the article

• Bad network performance on KVM guest

  - by Devator

  I have a dedicated server connected to a 1000 Mbit port. However, the Debian guest is only getting half to a 1/4 the speeds: On the node itself (Linux node 2.6.32-279.9.1.el6.x86_64 #1 SMP Tue Sep 25 21:43:11 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux): wget http://www.bbned.nl/scripts/speedtest/download/file1000mb.bin -O /dev/null --2012-11-11 23:10:11-- http://www.bbned.nl/scripts/speedtest/download/file1000mb.bin Resolving www.bbned.nl... 62.177.144.181 Connecting to www.bbned.nl|62.177.144.181|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1048576000 (1000M) [application/octet-stream] Saving to: â/dev/nullâ 100%[====================================>] 1,048,576,000 100M/s in 10s 2012-11-11 23:10:21 (100 MB/s) - â/dev/nullâ On the guest (Debian 6.0.5, x64: Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux): wget http://www.bbned.nl/scripts/speedtest/download/file1000mb.bin -O /dev/null --2012-11-11 23:10:41-- http://www.bbned.nl/scripts/speedtest/download/file1000mb.bin Resolving www.bbned.nl... 62.177.144.181 Connecting to www.bbned.nl|62.177.144.181|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1048576000 (1000M) [application/octet-stream] Saving to: â/dev/nullâ 100%[=================================================================================================================================================================================================>] 1,048,576,000 16.5M/s in 42s 2012-11-11 23:11:23 (23.8 MB/s) - â/dev/nullâ I use the virtio NIC. I tried some more NICs: e1000 and the Realtek 8139 but those yield even worse results. Anyone has an idea how to improve these speeds?

  Read the article

< Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >