Search Results

Search found 11364 results on 455 pages for 'port blocking'.

Page 154/455 | < Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >

• With Ubuntu Linux (10+), how do I connect to remote to my machine from Windows

  - by Berlin Brown

  I tried to to remote into my Ubuntu machine. I enabled the setting on Ubuntu and that side seems to work. But I get a connection time out when I use RealVNC on the Windows box. I believe it is a firewall issue. I disabled the firewall for that application on Windows but I don't know how to check if the firewall is enabled on the windows machine. I am on a local network with a router. Ideally, I would want to block that remote control port at the Internet level/router level but "enable" that port on the Windows box and the Ubuntu box. How do I check those settings.

  Read the article

• Creating a dynamic lacp trunk from HP Procurve 2412zl to Proliant DL380 G7

  - by Maalobs

  I'm configuring an IEEE 802.3ad (LACP) dynamic trunk from a HP Procurve 2412zl (firmware version K.15.07) switch to a HP Proliant DL380 G7 server. The DL380 has 4 NICs and is running Win2008 R2, so I'm teaming the NICs together and leaving everything on the recommended "automatic" setting in the HP NIC configuration tool. The server is one of two, they'll be connected on interfaces F17-F20 and F21-F24 respectively on the switch. I need the servers in a separate VLAN, here is the configuration for the VLAN: vlan 10 name "Lab_Mgmt" untagged B2,F17-F24 ip address 172.22.71.3 255.255.255.0 tagged B21 exit There is a DHCP-relay into the VLAN 10 from another device beyond interface B21. The Advanced Traffic Management Guide says that in order to run a dynamic LACP trunk on another VLAN besides the DEFAULT_VLAN, you need to first enable GVRP and then use "forbid" to stop the interfaces from automatically joining DEFAULT_VLAN when the dynamic trunk is created. GVRP brings some other stuff with it that I don't want or need, so I disable it with "unknown-vlans disable" on all other interfaces. Here is how I do it: procurve-5412zl-1(config)# gvrp procurve-5412zl-1(config)# interface A1-A24,B1-B24,C1-C24,D1-D10,D13-D24,E1-E24, F1-F16,K1,K2 unknown-vlans disable procurve-5412zl-1(config)# vlan 1 forbid F17-F24 procurve-5412zl-1(config)# interface F17-F20 lacp active The result afterwards looks all successful: procurve-5412zl-1(config)# show trunks Load Balancing Method: L3-based (Default), L2-based if non-IP traffic Port | Name Type | Group Type ---- + -------------------------------- --------- + ------ -------- F17 | XYZTEAM3_NIC1 100/1000T | Dyn2 LACP F18 | XYZTEAM3_NIC2 100/1000T | Dyn2 LACP F19 | XYZTEAM3_NIC3 100/1000T | Dyn2 LACP F20 | XYZTEAM3_NIC4 100/1000T | Dyn2 LACP procurve-5412zl-1(config)# vlan 10 procurve-5412zl-1(vlan-10)# show lacp LACP LACP Trunk Port LACP Admin Oper Port Enabled Group Status Partner Status Key Key ---- ------- ------- ------- ------- ------- ------ ------ F17 Active Dyn2 Up Yes Success 0 0 F18 Active Dyn2 Up Yes Success 0 0 F19 Active Dyn2 Up Yes Success 0 0 F20 Active Dyn2 Up Yes Success 0 0 On the Proliant server, the NIC configuration Tool is also indicating that a 802.3ad dynamic trunk has been established. Everything should be good, but it isn't. The server is not getting an IP-address from the DHCP, which it does if I'm not enabling LACP. If I configure the server to a static IP-address on the VLAN 10 subnet, it can't even ping the switch IP-address, much less anything outside of the VLAN. The switch can't ping the server either. I did another attempt with F17-F20 tagged, and checking the box "Default Native Tag (VLAN 10)" in the NIC configuration tool on the server, but there was no difference. Does anyone have any idea what I might have missed?

  Read the article

• Using VLC as RTSP server

  - by StackedCrooked

  I'm trying to figure out how to use the server capabilities of VLC. More specifically, how to export an SDP file when RTP streaming. In chapter 4 in the section related to RTP Streaming examples for server and client are given: vlc -vvv input_stream --sout '#rtp{dst=192.168.0.12,port=1234,sdp=rtsp://server.example.org:8080/test.sdp}' vlc rtsp://server.example.org:8080/test.sdp It's not very clear to me how to make it actually work. I have tried these two commands for server and client using two cmd instances: vlc -I rc screen:// --sout=#rtp{dst=127.0.0.1,port=4444,sdp=rtsp://localhost:8080/test.sdp} vlc -I rc rtsp://localhost:8080/test.sdp Invoking the second command causes the first one to crash. The second command shows the error message "could not connect to localhost:8080".

  Read the article

• Fedora to Fedora remote desktop does not work (connection closed error, even after setting everything up)

  - by jonderry

  I'm trying to use remote desktop on my laptop (running Fedora) to my desktop (also running Fedora) on the same local network. I configured Remote Desktop on my desktop via System - Preferences - Remote Desktop, verified that the port is open by nmap, and attempted to connect from my laptop via vinagre (also tried appending :5900 for the port, and using the ip address). In all cases, the connection fails with a popup that says "Connection closed\n Connection to host was closed." EDIT: I am able to use vinagre from the desktop to remote desktop into itself, just not from one machine to the other. I tried vncviewer and a similar problem occurs (unable connect to socket: No route to host (113))

  Read the article

• FTP connection is aborted

  - by Conrad C

  I want to connect using FTP to my webpage hosted on ipages.com , but I always get this error on filezilla.: Status: Server does not support non-ASCII characters. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 550 PWD: Permission denied Error: Failed to retrieve directory listing Error: Disconnected from server: ECONNABORTED - Connection aborted It looks like the connection is established but then disconnects. Is it an issue with the host? I use the default port 21. The user-pass is working. And the ftp adress is ftp.mysite.com I tested the port 21 using netstat and I get 220 Ipage FTP Server Ready

  Read the article

• How would I reset a usb hub multiplier driver?

  - by Cameron

  I have a usb port which connects a little man usb hub I got for Christmas. It worked fine to begin with however now it works on any computer other than my own. When I plug the man in it lights up and when I plug things into the man it says they have malfunctioned but when I plug them straight into tha port it's fine. Is there somesort of driver that needs to be refreshed? I have no idea how these work so please explain! I use windows 7 32bit.

  Read the article

• Enabling fastCGI for php in PLESK 9.3 or use ningx

  - by Saif Bechan

  I have a server that runs PLESK. I can set php to use 3 options: apache module, fastCGI application, cgi application And i have a different option that just says enable fastCGI support. Which option is the best to choose from? I run an php application with mysql and some ajax. Heavy reads and writes, it is a busy website. Second thing is will there be much difference if i install nginx to work with this. there is some sort of hack i can use to make ningx work on port 80 and apache on port 8080. I don't know if this is worth my while. thanks for your time folks!

  Read the article

• 8Gb Fiber Channcel HBA vs. 10 Gb SPF+ Converged HBA

  - by Hossein Aarabi

  I am putting a Dell server together, more specifically R720. I have to select the correct Host Bus Adapter. This HBA on R710 will connect to a storage device. I am confused between these two: QLogic 2562, Dual Port 8Gb Optical Fiber Channel HBA (price $2,045) QLogic 8262, Dual Port 10Gb SFP+, Converged Network Adapter (price $1,618) I thought since the QLogic 2562 is a fiber channel and is more expensive then it is faster in terms of IOPS. But, it is a 8Gb as opposed to 10 Gb of SFP+. My questions: Which one is better (IOPS performance, etc.)? Why should I choose one over another?

  Read the article

• Bugmenot (registration bypasser) alternative that doesn't suck?

  - by davr

  I used to love Bugmenot...but then they started blocking more and more sites. Now I'd say a good 75% of the time I try to find logins on bugmenot, the site is blocked. Is there a service like bugmenot that doesn't block sites? EDIT: For example, all of these sites require registration to download files, and all of them are blocked from BugMeNot. To be clear, this problem is because BugMeNot stops users from adding logins for them, not because of the individual sites themselves: dcemu.co.uk, ubuntuforums.org, club.cdfreaks.com

  Read the article

• Apache Redirect to Jboss SSL

  - by Rick

  I'm trying to have an SSL Connection to an Apache server on port 443 which I want to use to proxy connections to a JBoss server on a different port. The SSL certificates sit on the Jboss server not on the Apache server. Is it possible to redirect HTTPS traffic from Apache to the Jboss Server and have the JBoss server do the SSL handshake? The Apache server must be able to redirect HTTPS traffic for two different URLS. One for a secure site. The other for access to web services. By the way I'm using it mutual authentication, if that makes any difference. What does the Apache config file need to contain? or are there any good example of this out there? Thanks

  Read the article

• Good idea to use NLB for DNS servers?

  - by I.T. Support

  Is it a good idea to use NLB to load balance DNS requests to primary and secondary dns servers on port 53?

  Read the article

• Option 82 and dhcpd. "No free leases" for second computer

  - by SaveTheRbtz

  There is DHCP server in network (isc-dhcpd-server-3.0 on FreeBSD 7.2) than gives one IP per switch port to every user via Option 82 The problem appears when user disconnects one of his computers and connects another(i.e notebook with different MAC address) then DHCPD puts to log "...network net1: no free leases", because there is record in leases file that this IP is already owned by another MAC. That second computer will have his IP only after default-lease-time (that is IIRC minimum 10min, and after 3min he usually calling support) or after deletion of dhcpd.leases file and restart of dhcpd. Is there a way to turn leases off at all, because we have strict binding between switch-port-ip?

  Read the article

• AIX: iscsi volumes disappear after reboot

  - by Dan

  We have an IBM P505 AIX box, with two internal disks and a defined iSCSI volume. The iSCSI volume is defined in it's own volume group, and is connected to an IBM iSCSI DS3300 disk array via the secondary onboard ethernet port (ie, we're not using a dedicated HBA, we're using the second onboard ethernet port for iSCSI exclusively.) When we reboot the AIX box, the iSCSI volume doesn't get mounted (which is fine; I've figured out that it fails to mount because AIX tries mounting it's volumes before starting the networking stack.) The problem is, after the server has booted it fails to redetect the iSCSI target as a physical disk. This means the volume group (iscsivg) can't go online. if I run cfgmgr -v to redetect the iscsi volume it successfully detects the iscsi target volume and creates a physical volume reference, but allocates it a different volume ID to what was defined before. eg - rootvg contains hdisk 0 and 1 iscsivg was originally defined with hdisk2 as the physical iSCSI volume. after reboot and running cfgmgr -v, AIX detects physical volumes hdisk0, hdisk11 and hdisk3. As there's no hdisk2, I can't varyon the iscsivg volume group. I can't seem any existing hdisk2 definition in the ODM. I can't easily add or change the definition of the physcial disk in the iscsivg volume group as it won't "varyon". Exporting the volume group deletes it completely, recreating the volume group by "importing" it from the reallocated disk makes it available again, but surely there's a better way? Can I force a specific hdisk drive designation for an iscsi target? How do you bring online iSCSI volumes after a reboot? I assume this "just works" with a dedicated HBA instead of a generic ethernet adapter? By the way, the iSCSI volume works fine once it's mounted; we only have problems getting it working - and only with AIX. The iSCSI array works fine with our Linux and Windows servers; ie the volumes get detected and remounted after boot time without any problems, using generic ethernet adapters. Here's some of the config from the AIX box: defined disks / devices: # lsdev hdisk0 Available 06-08-01-5,0 16 Bit LVD SCSI Disk Drive hdisk1 Available 06-08-01-8,0 16 Bit LVD SCSI Disk Drive hdisk3 Available Other iSCSI Disk Drive iscsi0 Available iSCSI Protocol Device scsi0 Available 06-08-00 PCI-X Dual Channel Ultra320 SCSI Adapter bus scsi1 Available 06-08-01 PCI-X Dual Channel Ultra320 SCSI Adapter bus ses0 Available 06-08-01-15,0 SCSI Enclosure Services Device sisscsia0 Available 06-08 PCI-X Dual Channel Ultra320 SCSI Adapter iscsi target definition in /etc/iscsi/targets: # IBM DS3300 disk array # port 1 on second controller 10.10.xx.xxx 3260 iqn.1992-01.com.lsi:1535.600a0b80005b0a7fxxxxxxxxxxxx physical volumes (after reimporting the volume group) # lspv hdisk0 0003b08a0d4936b6 rootvg active hdisk1 0003b08aaa5cb366 rootvg active hdisk3 0003b08a032d04bb iscsivg active

  Read the article

• DD-WRT Router acting as a Switch and Wi-Fi AP

  - by dotnetchris

  Recently I upgraded to Comcast Business and their modem has a built-in router so I took off my DD-WRT router and moved to a location in my home where I needed more ports and Wi-Fi (preferably without running new Ethernet cables since it's 50-100 foot run through floor and ceilings). I have my network cable from my Comcast modem going into Port 1 of my DD-WRT router with Port 2 and 3 being networked PCs. I have DD-WRT setup as a DHCP forwarder with the firewall disabled. This lets my all of my devices access the network fine. Is the correct the way to do this? Or is this a less optimal solution and it should be done in a slightly different way?

  Read the article

• ISA Server 2006 SP1 :: Allow unauthenticated users (non domain users) access to external (internet)

  - by Klaptrap

  Now that we have applied an internal to external rule blocking all users access to the internet, other than those users in a whitelist, we have the obvious issue of non authenticated users, not on our domain, i.e.; domain-less guests not being able to access the internet. Other than configuring each machine to use our alternative gateway - which would require a member of IT to be onsite everytime a guest arrives - can this be done through ISA adn AD?

  Read the article

• network design to segregate public and staff

  - by barb

  My current setup has: a pfsense firewall with 4 NICs and potential for a 5th 1 48 port 3com switch, 1 24 port HP switch, willing to purchase more subnet 1) edge (Windows Server 2003 for vpn through routing and remote access) and subnet 2) LAN with one WS2003 domain controller/dns/wins etc., one WS2008 file server, one WS2003 running Vipre anti-virus and Time Limit Manager which controls client computer use, and about 50 pcs I am looking for a network design for separating clients and staff. I could do two totally isolated subnets, but I'm wondering if there is anything in between so that staff and clients could share some resources such as printers and anti-virus servers, staff could access client resources, but not vice versa. I guess what I'm asking is can you configure subnets and/or vlans like this: 1)edge for vpn 2)services available to all other internal networks 3)staff which can access services and clients 4)clients which can access services but not staff By access/non-access, I mean stronger separation than domain usernames and passwords.

  Read the article

• How to hack airport extreme to support USB 3G modem?

  - by Mike Caron

  Has anyone out there ever tried to hack the Airport Extreme, specifically with regard to the USB port? There are many cellular routers available that provide WiFi sharing of a USB modem link. However, instead of buying yet another router, I'd like to use my expensive Airport Extreme with it. The AE has a USB port on the back, but it's been said that it only talks to printers. Is there a way to hack the USB driver on the AE to allow it to recognize a USB modem, then use that as the connectivity instead of the LAN? I would imagine that one could use OpenFirmware to boot something on the AE. If one can boot it, then one could provide access using SSH across the lan. Once access is granted, then let the hacking begin... but I don't know how to (a) get the mini-osx on to USB (is it the same as the ATV without a UI?) or (b) how to load up certain things once boot has begun.

  Read the article

• Setting CATALINA_OPTS for tomcat6 on windows doesn’t work.

  - by Ben

  (I've copied this from Stack Overflow here, after someone suggested I post the question here) Hi, I'm trying to setup Tomcat6 to work with JMX on Windows Vista 64. To do that I need to pass the parameters below to Tomcat6. What I do in command prompt. (that doesn't work) set CATALINA_OPTS="-Dcom.sun.management.jmxremote -Dcom.sun.management.jmxremote.port=9898 -Dcom.sun.management.jmxremote.ssl=false -Dcom.sun.management.jmxremote.authenticate=false" tomcat6.exe What I do that does work (but causes other problems) java -Dcom.sun.management.jmxremote -Dcom.sun.management.jmxremote.port=9898 -Dcom.sun.management.jmxremote.ssl=false -Dcom.sun.management.jmxremote.authenticate=false -jar bootstrap.jar It seems as if tomcat is just ignoring the environment variable CATALINA_OPTS. Am I doing something wrong? I've also tried to edit catalina.bat and define the variable CATALINA_OPTS there. No success. (tried adding the parameters to JAVA_OPTS too, no success either) Thanks in Advance!!

  Read the article

• how to reset the IIS settings ..

  - by infant programmer

  I had been practicing ASP on my local machine.. I just wanted to change the TCP port address to 8080 and that is what I did, since then the URL "http://localhost/" is showing PAGE CANNOT BE DISPLAYED, and technical reason being shown is : "You have attempted to execute a CGI, ISAPI, or other executable program from a directory that does not allow programs to be executed." I tried to change back the TCP port address to 80, (which is default) but its not making any difference. What should I do now, to make localhost to work as before ? When I create a virtual directory for the same path "C:/InetPub/wwwroot" then it works but with this URL "http://localhost/virualname/filename.asp" .. where as "http://localhost/filename.asp" throws error, as mentioned above. Can you please explain me what is this consequence is?? thank you :) Details: IIS verion is 7, OS XP,

  Read the article

• Unable to run openoffice in headless mode

  - by uswaretech

  I want to automoate some PPT - PDF conversions, so I want to run openoffice in headless mode for scripting. On my machine with X running I can start opemoffice in headless mode via soffice -accept="socket,port=8100;urp;" -headless This doesn't seem to work on a server with X not running. $ soffice -accept="socket,port=8100;urp;" -headless /usr/lib/openoffice/program/soffice.bin X11 error: Can't open display: Set DISPLAY environment variable, use -display option or check permissions of your X-Server (See "man X" resp. "man xhost" for details) $ The error doesnt seem to make sense as well, as the point of specifying -headless was so that I do not need X, while this command seems to look for X.

  Read the article

• Queston about torrents

  - by c0mrade

  Why do my torrents go at rate 25/30 kb/s and my regular http downloads rate up to 300 kb/s .. is my ISP to blame for this, I meant torrents have like thousand seeders and again its very slow.How are they blocking torrent speed, can I bypass it?

  Read the article

• 8051 MCU debug board function

  - by b-gen-jack-o-neill

  Hi, in school I have written many programs for 8051 compatible CPU. But I never actually knew how our "debug" sets worked. I mean, we test our programs in special sets, which actually allow you to very simply load program to CPU via PC serial port. But I thing you know this musch more better than I. But how it works? I mean, I know there is chip which adjusts signal level from PC serial port to TTL logic, and than connected to serial line of 8051. But thats all I know. Actually even my teacher doesen´t know how it works, since school bought it all. So, I suspect there is some program already running in the 8051 which handles communication and stores your program into memory, am I right? But, how can you make 8051 to process instructions from different location than ROM? Becouse if I am right, you cannot write into ROM memory by any instruction, as well as 8051 can only read instructions from ROM?

  Read the article

• Mounting NFS share between OSX and Centos VM

  - by Adam

  I'm having issues mounting an NFS share I've made on my Mac host (server) from a Centos VM (client). I'm getting a permission denied error. I have this line in /etc/exports on server: /Users/adam/Sites/ 192.168.1.223(rw) and in /etc/fstab on client: 192.168.1.186:/Users/adam/Sites/ /home/adam/Sites/ nfs rw 0 0 I'm sure this is a simple configuration issue, but I've never set up NFS properly before. Extra info: # mount -v 192.168.1.186:/Users/adam/Sites/ /home/adam/Sites/ mount: no type was given - I'll assume nfs because of the colon mount.nfs: timeout set for Mon Nov 26 07:31:40 2012 mount.nfs: trying text-based options 'vers=4,addr=192.168.1.186,clientaddr=192.168.1.223' mount.nfs: mount(2): Protocol not supported mount.nfs: trying text-based options 'addr=192.168.1.186' mount.nfs: prog 100003, trying vers=3, prot=6 mount.nfs: trying 192.168.1.186 prog 100003 vers 3 prot TCP port 2049 mount.nfs: prog 100005, trying vers=3, prot=17 mount.nfs: trying 192.168.1.186 prog 100005 vers 3 prot UDP port 958 mount.nfs: mount(2): Permission denied mount.nfs: access denied by server while mounting 192.168.1.186:/Users/adam/Sites/

  Read the article

• Running jira at jira.[my domain].com

  - by Ivan Zamylin

  I have jira installed on my server. It was running at http://[my ip address]:8100. I could manage to change it to http://jira.[my domain].com. Now after I access it at http://jira.[my domain].com, a browser path changes to http://jira.[my domain].com:8100/secure/Dashboard.jspa. Why does the port show up? Is there any way to remove 8100 port from this redirect. I'd like it to be http://jira.[my domain].com/secure/Dashboard.jspa Also my jira now responds both to jira.[my domain].com and [my ip address]:8100. The latter one is corrupted. Is it possible to stop user accessing it? Thank you!

  Read the article

• Dual Nic, one keeps dropping

  - by user1215018

  I'm running windows server 2008 r2 on a dell poweredge 2850. I have 2 NICs, one is configured behind a firewall with a dhcp server on the main local LAN and another one has it's own dedicated connection to one of our 13 static IPs. So in a nutshell we have 2 of our static IPs going to this server, one indirectly through a firewall/dhcp server, and the other directly. I am trying to reach IIS on port 80 and port 443. The problem is that the NIC with the direct connection (NIC2) keeps dropping and says either "No internet connection" or "Unauthenticated". However, the NIC behind the firewall (NIC1) has no problems at all. Update: This is the second time this has happened in 3 days and each time the fix has been enabling the dhcp client on the NIC, allowing it to error out to a 169.x.x.x address, then re-enabling the nic with it's static IP assignment.

  Read the article

< Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >