Search Results

Search found 5124 results on 205 pages for 'week'.

Page 154/205 | < Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >

• File transfer problems through VPN when Cisco IPS is enabled

  - by Richard West

  We have a Cisco ASA 5510 firewall with the IPS module installed. We have a customer that we must connect to via VPN to their network to exchange files via FTP. We use the Cisco VPN client (version 5.0.01.0600) on our local workstations, which are behind the firewall and subject to the IPS. The VPN client is successful in connecting to the remote site. However when we start the FTP file transfer we are able to upload only 150K to 200K of data, then everything stops. A minute later the VPN session is dropped. I think I have isolated this to an IPS issue by temporarily disabling the Service Policy on the ASA for the IPS with the following command: access-list IPS line 1 extended permit ip 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 inactive After this command was issued I then established the VPN to the remote site and was successful in transferring the entire file. While still connected to the VPN and FTP session I issued the command to enable the IPS: access-list IPS line 1 extended permit ip 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 The file transfer was tried again and was once again successful so I closed the FTP session and reopened it, while keeping the same VPN session open. This file transfer was also successful. This told me that nothing with the FTP programs was being filtered or causing the problem. Furthermore, we use FTP to exchange files with many sites everyday without issue. I then disconnected the original VPN session, which was established when the access-list was inactive, and reconnected the VPN session, now with the access-list active. After starting the FTP transfer the file stopped after 150K. To me this seems like the IPS is blocking, or somehow interfering with the initial VPN setup to the remote site. This only started happening last week after the latest IPS signature updates were applied (sig version 407.0). Our previous sig version was 95 days old becuase the system was not auto updating itself. Any ideas on what could be causing this problem?

  Read the article

• IPCop server slows down download speed

  - by noocyte

  I have an IPCop server running at home, been doing just fine for ~5 months, but last week I suddenly started getting time-outs and slow downloads from the 'net. I first thought that this was my ISP acting up, then I thought it might be one of my 3 switches or some of my cabling. In due order I've tested everything above and found them all to be working as they should. The only factor remaining is my IPCop server. Facts: I've got a 15/15 Mbit line (fiber) and I get ~15 Mbit upload, but only 0.5 Mbit download with the IPCop box as router (ISP router set in bridge mode). If I connect without the IPCop box (using the ISP router) I get ~12 Mbit upload and ~15 Mbit download. The load on the IPCop box appears to be light and it used to handle this traffic just fine 2 weeks ago. The memory usage is ~60%, I tried to restart it and test again, the memory fell to ~50% then (5 months of uptime). I'm thinking that one of my nics are busted, but I'm sort of perplexed that this could be the outcome; slow download but full speed upload. Anybody ever seen that happening before? Could it just be one of the nics that needs to be replaced? Will try that as soon as I can get my hands on a couple of new ones.

  Read the article

• Occasional "Could not load file or assembly" in asmx WebService on IIS and DFS

  - by user8804

  We have a handfull of ASMX web service hosted on two identical Windows Server 2003 boxes. The virtual directory for the web services is loaded in a DFS share, both servers point to the same share. We have a load balancer between the internet and the two web servers. At a seemingly random interval (right now about twice per week) when a user tries to access a method on the web service, IIS returns the error: "Could not load file or assembly" for one of the assemblies used in the method call, and will continue reporting it each time the method is called until the app pool is recycled. We haven't found any distinguishable pattern to the problem. This is what I know: the missing assembly varies (but it's always a home-brew assembly) the Web Service method that fails varies there is no noticeable pattern to the times or intervals where the problem appears there are no admin users accessing the servers when the problem appears the failing method will work correctly on one server and fail on the other, even though both point to the same bin folder the problem can always be corrected by recycling the app pool and making no other changes I have enabled the Assembly Binder Log, and know that the binder is looking in the correct location for the file. Our assemblies are compiled for .Net 3.5.

  Read the article

• RAID1 Broken Mirroring

  - by Sanoj

  I'm having a little server with Windows Small Business Server 2003. I'm using RAID1, via a HighPoint Rocket RAID 1640 RAID-card, using two harddrives. This week the server alarmed, and durig reboot I got the error-message Broken Mirroring (User Manual page 30). I had a few alternatives (see the manual), first I tried Continue, but the server restarted during boot. Next time I took Power Off, and replaced the oldest harddrive with a new one, and when I booted, I selected Rebuild. Then I selected the new harddrive to be the new one. The rebuild-procedure started and a progress bar at 0% showed up, but after a few seconds I got the message Copy Failed!, then the server booted and Windows Server started. Now it works fine. But I guess that I'm just using one harddrive now, and it's not mirrored. I haven't touched the server since then (two days ago). What should I do now? I have no experience of this situation. Anyone that have some guidance?

  Read the article

• SQL Server transaction log backups,

  - by krimerd

  Hi there, I have a question regarding the transaction log backups in sql server 2008. I am currently taking full backups once a week (Sunday) and transaction log backups daily. I put full backup in folder1 on Sunday and then on Monday I also put the 1st transaction log backup in the same folder. On tuesday, before I take the 2nd transaction log backup I move the first transaction log backup from folder1 an put it into folder2 and then I take the 2nd transaction log backup and put it in the folder1. Same thing on Wed, Thurs and so on. Basicaly in folder1 I always have the latest full backup and the latest transaction log backup while the other transaction log backups are in folder2. My questions is, when sql server is about to take, lets say 4th (Thursday) transaction log backup, does it look for the previous transac log backups (1st, 2nd, and 3rd) so that this new backup will only include the transactions from the last backup or it has some other way of knowing whether there are other transac log backups. Basically, I am asking this because all my transaction log backups seem to be about the same size and I thought that their size will depend on the amount of transactions since the last transaction log backup. Example: If you have a, lets say, full backup and then you take a transac log backup and this transac log backup is lets say 200 MB and now you immediatelly take another transac log backup, this last transac log backup should be considerably smaller than the first one because no or almost no transaction occured between these two backups, right? At least, that's what I've been assuming. What happens in my case is that this second backup is pretty much the same size as the first one and I am wondering if the reason for that is because I moved the first transac log backup to a different folder so now sql server thinks that all I have is just a full backup and it then gets all the transactions that happened since the full backup and puts it in the 2nd transac log backup. Can anyone please explain if my assumptions are right? Thanks...

  Read the article

• Iverter, inverter cable, or a display cable?

  - by krebshack

  I was recently hired at a small repair shop. I work indoors while my boss does on site calls for small businesses. I have to troubleshoot and fix laptop screens a few times a week and this is why I'm posting this question. I'm having trouble figuring out how to stream line the troubleshooting process. For example, how do I determine whether the inverter is broken while also determining that the inverter cable is not. How can I quickly decide that the inverter cable is broken while knowing that the inverter is most likely not broke. Or how do I know that it's just the display cable? It seems like this is a good way to approach things: "It could be the inverter, backlight, or the LCD panel itself. Backlight failure is usually hinted at by a pink hue to everything. Inverter failure usually results in the dimming of images on the screen to the point where the backlight is not even on (the inverter provides power to the backlight)" Source. While remembering that things "like flickering, screen freeze in dark image and [a] corner starts to get brighter" point to a "failure in the LCD panel itself, though it could just as easily be a loose data cable connected to the back of the LCD." Source. In short, I'm soliciting advice that anyone might have on how to quickly make the best decision about what's causing problems with laptops display. Thank you.

  Read the article

• Backup program for Windows using non-proprietary format?

  - by Cristi Diaconescu

  I'm looking at the various local backup programs for windows, and I was wondering which of them use a non-proprietary backup format? By non-proprietary, I mean I want to be able to access at least the latest version of the backed up files either directly, or by using an open-standard format like zip/7z/rdiff... The other thing I'm looking for in a backup program is the ability to create incremental backups. What I have found so far: SyncBack copies files as-is, using separate directories for versioning pretty much the same for all the 'roll you own' task scheduler + rsync/xcopy32/robocopy/MS SyncToy/etc solutions GFI Backup appears to be using Zip files, at least in their 'Business' version, not sure about the free 'Home' version. Didn't try it yet, but it's next on my list. Mozy (!) supports local backup starting with v 2.0 and basically provides a 2nd local copy on a separate partition. Subjectively, it feels slow and resource intensive (I think it took more than a week to finish the first local backup of ~ 300 GB), and does not appear to offer file versioning (arguably, you can get older file versions online). On the positive side, it looks like the local backup is integrated in the restore process which was traditionally a masochistic experience (and this goes for any online backup provider). Other suggestions? I favor ease of use over tons of options (e.g. SyncBack is very flexible but it offers sooo many ways to shoot yourself in the foot...)

  Read the article

• Occasional "Could not load file or assembly" in asmx WebService on IIS and DFS

  - by jesse-mcdowell

  We have a handfull of ASMX web service hosted on two identical Windows Server 2003 boxes. The virtual directory for the web services is loaded in a DFS share, both servers point to the same share. We have a load balancer between the internet and the two web servers. At a seemingly random interval (right now about twice per week) when a user tries to access a method on the web service, IIS returns the error: "Could not load file or assembly" for one of the assemblies used in the method call, and will continue reporting it each time the method is called until the app pool is recycled. We haven't found any distinguishable pattern to the problem. This is what I know: the missing assembly varies (but it's always a home-brew assembly) the Web Service method that fails varies there is no noticeable pattern to the times or intervals where the problem appears there are no admin users accessing the servers when the problem appears the failing method will work correctly on one server and fail on the other, even though both point to the same bin folder the problem can always be corrected by recycling the app pool and making no other changes I have enabled the Assembly Binder Log, and know that the binder is looking in the correct location for the file. Our assemblies are compiled for .Net 3.5.

  Read the article

• "Cannot perform a differential backup for database "myDb", because a current database backup does no

  - by krimerd

  Hi there, I have what seems to be a pretty common problem when trying to take a differential backup. We have a SQL Server 2008 Standard (64bit) and we use Litespeed v 5.0.2.0 to take our backups. We take full backups once a week and a differential on a daily basis. The problem is, every time I try to take a diff backup I get the following error: "VDI open failed due to requested abort. BACKUP DATABASE is terminating abnormally. Cannot perform a differential backup for database "myDb", because a current database backup does not exist. Perform a full database backup by reissuing BACKUP DATABASE, omitting the WITH DIFFERENTIAL option." The problem is that I know 100% I have a full backup because I just double checked. Only once I was able to take a diff backup and that was when I took it immediately after I took a full backup. I have searched around and noticed that this is pretty common (although mostly with SQL 2005) and a solution that a lot of ppl suggest and that I haven't tried yet is to disable the SQL Server VSS Writer service. The problem with this is #1 I think I might need this service since I am using a third party backup software and #2 I am not sure exactly what the service does and don't want to disable it just like that. Has any of you ever experienced this problem and how did you go about fixing it? Thank you,

  Read the article

• Ubuntu Postfix Gmail SMTP Relay Not Working

  - by Nick DeMayo

  I currently have postfix set up to relay messages from my websites through gmail, and up until recently it was working perfectly. However, within the last week or so (not really sure when) I started getting the below error whenever attempting to send an email: Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[2001:4860:800a::6c]:587: Network is unreachable Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[173.194.76.109]:587: Connection refused Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[173.194.76.108]:587: Connection refused Here is my configuration file: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h #readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = [my domain name] alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases #myorigin = /etc/mailname mydestination = [my host name], localhost.localdomain, localhost relayhost = [smtp.gmail.com]:587 mynetworks = 127.0.0.0/8 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = loopback-only inet_protocols = all ########################################## ##### non debconf entries start here ##### ##### client TLS parameters ##### smtp_tls_loglevel=1 smtp_tls_security_level=encrypt smtp_sasl_auth_enable=yes smtp_sasl_password_maps=hash:/etc/postfix/sasl/passwd smtp_sasl_security_options = noanonymous ##### map username@localhost to [email protected] ##### smtp_generic_maps=hash:/etc/postfix/generic Nothing changed on my server, as far as I know...any ideas what could have caused it to stop working?

  Read the article

• ZFS - destroying deduplicated zvol or data set stalls the server. How to recover?

  - by ewwhite

  I'm using Nexentastor on a secondary storage server running on an HP ProLiant DL180 G6 with 12 Midline (7200 RPM) SAS drives. The system has an E5620 CPU and 8GB RAM. There is no ZIL or L2ARC device. Last week, I created a 750GB sparse zvol with dedup and compression enabled to share via iSCSI to a VMWare ESX host. I then created a Windows 2008 file server image and copied ~300GB of user data to the VM. Once happy with the system, I moved the virtual machine to an NFS store on the same pool. Once up and running with my VMs on the NFS datastore, I decided to remove the original 750GB zvol. Doing so stalled the system. Access to the Nexenta web interface and NMC halted. I was eventually able to get to a raw shell. Most OS operations were fine, but the system was hanging on the zfs destroy -r vol1/filesystem command. Ugly. I found the following two OpenSolaris bugzilla entries and now understand that the machine will be bricked for an unknown period of time. It's been 14 hours, so I need a plan to be able to regain access to the server. http://bugs.opensolaris.org/bugdatabase/view_bug.do?bug_id=6924390 and http://bugs.opensolaris.org/bugdatabase/view_bug.do;jsessionid=593704962bcbe0743d82aa339988?bug_id=6924824 In the future, I'll probably take the advice given in one of the buzilla workarounds: Workaround Do not use dedupe, and do not attempt to destroy zvols that had dedupe enabled. Update: I had to force the system to power off. Upon reboot, the system stalls at Importing zfs filesystems. It's been that way for 2 hours now.

  Read the article

• Multiple vlans access to shared pbx system

  - by Matt

  I'm new to networking and was looking for some assistance. First off I'm using packet tracer to diagram my scenario as I will be receiving my equipment next week to deploy. Hardware to be used: 2 catalyst 3560 switches all connect to a sonic wall router I have two companies that work in the same office space. I need to keep these companies separate on their own vlan. They will however need to share the phone system. (Packet tracer file uploaded to give those who have the time to see what I put together.) http://dl.dropbox.com/u/86234623/network%20build.pkt Here is my current test scenario: on switch 0 I have: company A on vlan 2 computers 172.16.1.100 and 101 255.255.0.0 FA0/10 FA0/11 company B on vlan 3 computers 172.16.2.102, 255.255.0.0 FA0/12 PBX on a trunk port 172.16.0.5, 255.255.0.0 FA0/5 trunk port on FA0/1 to connect the switches on switch 1 I have: company A on vlan 2 computers 172.16.1.102, 255.255.0.0 company B on vlan 3 computers 172.16.2.100 and 101, 255.255.0.0 trunk port on FA0/1 to connect the switches I can ping the respective computers on the same vlan but cant ping company A to B which is what I want. However neither company can talk (ping) the PBX. Here are the commands I used to configure what I have: switch 0 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 2 int fa0/11 switchport mode access switchport access vlan 2 int fa0/12 switchport mode access switchport access vlan 3 int fa0/5 switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 Switch 1 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 3 int fa0/11 switchport mode access switchport access vlan 3 int fa0/12 switchport mode access switchport access vlan 2 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3

  Read the article

• .com domain transfer failing

  - by digital

  Hi, I'm trying to transfer one of my .com addresses between registrars. I'm down as the owner contact (confirmed working) and the losing registrar is down as the tech and admin contact. Last week I received an email stating that the domain transfer had been rejected by the losing registrar. I contacted the losing registrar and they denied that. My money from the winning registrar was refunded and I was told to try again. I've initiated the transfer again and received confirmation of pending transfer, I gave the correct EPP code and confirmed the transfer. Currently the status on the domain is set as OK, should it not be transfer pending? According to my name.com transfer page if the transfer is not authd in 5 days it will auto transfer anyway. I don't believe this will happen. Name.com have been really helpful but they can't really do much more now. The losing registrar is not being helpful hence me turning here. What can I do to make sure the domain transfers? The domain transfer is set to expire on the 17th. Any help would be greatly appreciated.

  Read the article

• run as dialog always pops up

  - by user12006

  I recently got some malware on a machine that I don't use for much (partly intentional). I've cleaned it, but now everytime I open any .exe the 'Run As' dialog pops up asking me which user I want to use to run the program. What causes this, and what's the fix for it? edit My process to remove the malware was as such: Disconnected from the network Deleted DisableTaskMgr reg key Inspected with Process Explorer and Task Manager and noticed that all applications were being run within another executable located in Documents and Settings...\Temp\Some.exe The system tray application was also in Documents and Settings...\Temp\SomeOther.exe I suspected that a service was in place as the system tray application would restart if it was killed, but couldn't find any service that I didn't recognize. Removed permissions from Some.exe and SomeOther.exe (on those files only) Restarted and deleted Some.exe and SomeOther.exe Deleted startup entries that were created Ran AVG Free and Windows Defender to remove anything else (they would be killed immediately before the two .exe's were removed) Cleaned registry via CCleaner note that system restores would finish saying something to the effect of 'couldn't restore system: there were no changes made'. I attempted to restore to a week ago, and I only got the malware yesterday.

  Read the article

• Intermittent PHP error: Undefined function <core function>

  - by Daniel

  In the last week I've been coming across an incredibly annoying error on one of Slicehost slices. It appears that every now and then PHP will fail with a fatal error, saying a certain function is undefined. The function changes, but is always a core PHP function e.g. defined(), version_compare(), etc. This problem has occurred while using several different PHP applications - PHPMyAdmin, my own custom built apps, etc, leading me to believe that the problem is not specific to the running code. Here are some details: - Debian Lenny - Apache 2.2.9 - PHP 5.2.6-1+lenny4 with Suhosin-Patch (running eAccelerator 0.9.6) Apache and PHP are installed from Debian packages. Error logs show nothing out of the ordinary. I thought memory might be an issue, but free -m reports upwards of 100MB free almost all the time. Another thing I'm trying to investigate is if the problem might be related to eAccelerator, but testing this theory out is incredibly hard because the issue doesn't appear very often and I've been using eAccelerator for months on this install without any problems up until now. Has anyone ever come across anything like this? Why would PHP report undefined core functions?

  Read the article

• DHCP forwarding behind access list on a Cisco Catalyst

  - by Ásgeir Bjarnason

  I'm having some trouble with forwarding DHCP from a subnet behind an access list on a Cisco Catalyst 4500 switch. I'm hoping somebody can see the mistake I'm making. The subnet is defined like this: (first three octets of IP addresses and vrf name anonymized) interface Vlan40 ip vrf forwarding vrf_name ip address 10.10.10.126 255.255.255.0 secondary ip address 10.10.10.254 255.255.255.0 ip access-group 100 out ip helper-address 10.10.20.36 no ip redirects I tried turning on a VMWare machine on this subnet that was configured to use DHCP, but I never got a DHCP response and the DHCP server didn't receive a request. I tried putting the following in the access-list: access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootps access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootpc access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootps access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootpc That didn't help. Can anybody see what the problem is? I know that the DHCP server works; our whole network is running off of this DHCP server I also know that the subnet works because we have active servers running on the network The DHCP scope is already defined on the DHCP server The subnet is correctly defined on the VMWare server (already servers running on the subnet on VMWare) Edit 2012-10-19: This is solved! The subnet had formerly been defined as a /25 network, but was then expanded into a /24 network. When the DHCP scope was altered after this change it was done incorrectly; the gateway was moved to .254, the leasable IP range was in the lower half of the /24 subnet but we forgot to change the CIDR prefix from /25 into /24. This happened some 2 years ago, and we didn't need to use DHCP on this server network again until this week. Thank you MDMarra and Jason Seemann for looking at the question and trying to troubleshoot. Now I'm wondering if I should mark Jason's answer as the accepted answer (I am new to the Stack Exchange network, so I don't know the etiquette of what to do if I misstated the question like in this case).

  Read the article

• Magento Apache Config & Memory Issues

  - by cheshirepine

  I have a Magento installation on a VPS that is giving me a headache. This particular VPS has a reasonable spec - 2gb Memory and 50gb storage. It runs a single domain, with a single Magento install - and nothing else. About 5 months ago we started having issues. Every so often (about once every 2 or 3 weeks) the VPS would crash - all processes stopped and the only way to restart the container is via Virtuozzo. Now, however its 2 or 3 times a week. My VPS hosts confirm I am breaching the 2gb memory limit, at which point all VPS processes are killed to stop it bringing the entire node down. I have not made any config changes to it at all - I was running New Relic on it for a short while, but have removed that in case it was contributing to the issues. I can see nothing in the logs which indicates an issue and we have no CRON jobs running at the time the crashes happen. The site generates steady, but not huge amounts of traffic (averaging usually less than 100 visits per day) Is there anything in particular I should have done to the Apache or PHP configs to help? Im not a massivley experienced Apache admin, but know more than enough to solve most problems... Failing that, any other ideas that might help? Can't afford for this site to be down this much.

  Read the article

• Can't access server on LAN new Router

  - by RMDan

  Earlier this week my roommates decided to change the router we are using for our home network. On the old router I had no problems accessing a laptop running Mint Linux over the network(SSH, FTP, and Shared Folders). However I am now not able to connect. I have verified the IP address of my Linux machine has not changed and I have no problems connecting to our NAS(WDMYCLOUD). The new router is a D-Link DIR-868L. PuTTY is giving me a Timed Out error(was giving me a EHOSTUNREACH before). Running Windows 8.1 the connecting laptop, but tried connecting using my phone via SSH did not work either. More information: Can ping the Linux machine from the router but not my computer. Pinging 192.168.0.111 with 32 bytes of data: Reply from 192.168.0.102: Destination host unreachable. Reply from 192.168.0.102: Destination host unreachable. Reply from 192.168.0.102: Destination host unreachable. Reply from 192.168.0.102: Destination host unreachable. Ping statistics for 192.168.0.111: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

  Read the article

• keyboard intermittently stops working even after reinstalling windows 7; possibly a Chrome issue?

  - by neverskipbreakfast

  My keyboard intermittently stops working. Sometimes a couple of keys will work, but usually none. Sometimes if I mash the ctrl+alt+windows keys randomly for a bit, the keyboard will let me type one more letter before stopping again. Sometimes the keys will open a program menu but usually not. I have even completely wiped my machine and reinstalled windows 7; the problem continues. Specs: Intel iMac (early 2006, 2.0GHz, 2MB RAM, 240GB HD) running ONLY Windows 7 Professional, 32-bit (NOT through boot camp) and using a USB keyboard (Saitek Eclipse II.) Unplugging & reconnecting keyboard does NOT fix it. Connecting a different keyboard does NOT fix it. That one won't work, either. Drivers are up-to-date. Removing and reinstalling drivers does NOT fix it. Restarting the computer does NOT fix it. In fact, when the Windows logon screen appears the keyboard won't work and neither will the icon to pull up the on-screen keyboard. My mouse can click around just fine. I can only log onto a non-password protected account. Generally, logging into as different Windows user fixes it. I can then log back on to my main user account and continue work for a few hours until it happens again. Clearing my Chrome browsing data stopped the problem from recurring for a week or so. I have already REINSTALLED Windows 7 (not just a restore.) The problem returned after 2 days of use. I use Avira free antivirus software, and repeated scans turn up nothing fishy. I suspect it is related to something in Google Chrome because I used my google account to reload all my previous Chrome extensions, saved data, etc. (Chrome Extensions Installed: AdBlock, Better Google Tasks, DropBox, FB Photo Zoom, Google Mail Checker, StayFocusd.) Any ideas? Any at all?

  Read the article

• Where is my free space?

  - by Andrey

  A week ago I got a low disk space warning on my Vista x64 Ultimate box - 60 Mb free on the disk C; I cleaned up some downloaded msdn images and got 20 Gb freed up. Three days ago I got another notification, it looked suspicious but I didnt have time to deal with it and just moved some heavy stuff to another drive to free up about 17 Gb.... Today morning - 53Mb left on drive C, again! Now it looks really suspecious, so I downloaded TreeSize to see what's taking up the space, just to see it reporting only 121 GB out of 200 GB used, in other words I suppose to have about 79 Gb free. Then I went to Folder Options, enabled viewing of system and hidden files, rerun teh tool to see another 5 Gb added (which is expected). Then I open disk C in windows explorer, select all and right click Properties, to see it reporting teh same amount of files - 126 Gb. But when I look at Drive C properties, it reports that 200GB of 200 Gb are taken. I just scanned the drive with two different antiviruses - Symantec and AVG and found no viruses... I'm a little confused at this point, any ideas where is my free space, woudl be highly appreciated! Thank you! Andrey

  Read the article

• UPS with a HP Proliant server

  - by Groo

  We placed a EATON Ellipse Max 1500 (900W) as the UPS for our HP Proliant ML350 G6. Upon first power failure (actually we only moved the UPS' input plug to a different socket), server immediatelly turned off, and the Health LED turned red and started blinking. UPS was in operation for about a week before that, with battery fully charged to 100%. Since our server's hot-plug supply is 460W, we are pretty sure we haven't overloaded it, the server was completely idle at that time (no web or win apps running except Windows Server core services). Then we tried to do the same with a different, no-name older PC (Core 2 Duo, 2Gb RAM) with a generic power supply (not sure what the power is) and it continued working when we pulled the plug out. UPS load was less than 15% (measured in the provided Eaton utility). We measured the UPS' output voltage using a smart oscilloscope and the THD of the UPS output waveform turned out to be 40%. Did you have similar experiences? Could this be a faulty UPS? Or a faulty power supply? Or some HP sensors configured to trigger too strictly? I wouldn't like replacing this UPS with the same brand, to get same results. [Edit] I also tried to do this while the server is turned off. While the UPS is working on battery, server will not start - as soon as I press the power button, Health LED starts blinking red.

  Read the article

• I keep losing wireless connection

  - by posfan12

  I have a WRT54GL v1.1 wireless router and a WUSB54G v4 wireless adapter, both made by Linksys. The router is in the living room by the TV and the my computer is in the bedroom. My ISP is Brighthouse. Operating System Microsoft Windows 7 Home Premium 64-bit SP1 CPU Intel Core 2 Duo E6600 @ 2.40GHz 36 °C Conroe 65nm Technology RAM 3.00GB Single-Channel DDR2 @ 333MHz (5-4-4-14) Motherboard eMachines EMCP73VT-PM (CPU 1) 26 °C Graphics ASUS VS247 (1920x1080@60Hz) 767MB GeForce GTX 460 (nVidia) 43 °C Hard Drives 466GB Seagate ST350041 8AS SCSI Disk Device (SATA) 35 °C Optical Drives HL-DT-ST DVDRAM GH41N SCSI CdRom Device Audio High Definition Audio Device The problem is that my Internet connection will work fine for 15 minutes or so. Then the data will just stop flowing. Windows says I am still connected, and the systray icon still shows five bars. But Comodo Firewall will stop showing up and down traffic, and another of my systray applications complains about a lack of connection. What I usually do is either disconnect from the network manually, or unplug and re-plug the USB adapter. At which point the connection will work properly for another 15 minutes. I've tried unplugging my router for 30 seconds and letting it reboot. I've also tried looking for a newer driver for my adapter but I seem to have the latest version 3.1.3.0. This is a recent problem starting about a week ago. For the previous several months things were working just fine. I haven't made any changes to my system that I am aware of. The only thing I did was open my case to blow the dust out of it, then put everything back together. How do I fix this issue?

  Read the article

• how to cause linux system datetime to run faster than real world datetime?

  - by JamesThomasMoon1979

  Background I want to monitor a running linux system over several days. It's a custom gentoo build and with much custom software on board. This software has ongoing maintenance timers and cron scripts and other clock driven events. I need to verify these scheduled events are working. Problem Waiting for the system to step through daily and weekly activity is a long wait time. And modifying all clock-based timers on the system would be time consuming. Yet, I often want to test a system's end-to-end scheduled activities without waiting a week. Potential Solution Have the linux system under test appear to run through it's daily cycle of activity within just a few hours. My Question for Serverfault Is there a way to cause the system's time to run faster than real world time? My first thought is manipulating the ntp daemon to repeatedly and smoothly increment the clock . Any other ideas? And yes, I know this may have strange side affects. However, the system has no important or time critical interactions with systems outside of itself. And this may be a valuable testing technique.

  Read the article

• How to repair a damage transaction log file for Exchange 2003

  - by Markus Larsson

  Hi! Yesterday we had a power failure and the UPS did not work (it has worked perfect before). Everything seem to be ok when I started all the servers again except of the mail, when I try to mount the store I get the following message: “The database files in this store are corrupted” Server: Exchange 2003 running on a Small Business Server Latest full backup: one week old Backup program: Backup Exec 9.0 This is what I have done: 1. Copy every file in the MDBDATA folder (edb, stm, log) 2. Run Eseutil /d for priv1.edb 3. Run Eseutil /p for priv1.edb (took seven hours) 4. Run Isintig –fix –test alltests, now it breaks down. Isintig fails with the following error: Isinteg cannot initiate verification process. Please review the log file for more information. The problem is that there is no log file created. 5. Giving up on this route I decide to do a restore from the backup, it fails with the following error: Unable to read the header of logfile E00.log. Error -501, and the error: Information Store (5976) Callback function call ErrESECBRestoreComplete ended with error 0xC80001F5 The log file is damaged. My conclusion is that E00.log is damage, so how can I repair it so that I can restore the database? Or should I give up and try some other route?

  Read the article

• Issues with sustained traffic with PFSense

  - by Farseeker

  Last week we had to replace our PFSense firewall because it had a catastrophic hardware failure. All but one of the NICs were taken out of the old server and put into the new one. The one NIC that was not moved was the LAN NIC as this is on-board. The other NICs are all WAN connections and the must all be present (i.e. I can't disable one just for the sake of testing) After re-installing PFSense and restoring our backup of the configuration, everything came back online just fine, however on the new hardware any download that takes longer than about 10 seconds just times out in the middle. Example 1: Downloading from Microsoft.com goes at about 900k/sec and times out after about 10 seconds (thus, just under 10Mb of content) Example 2: Downloading from cnet.com goes at about 300k/sec and times out after about 10 seconds (thus, about 3Mb of content). By times out, I mean that the download just stops, and you have to pause/resume to get the next part done, repeat and rinse until the download is complete. However it's not consistant, sometimes it's 10 seconds, sometimes it's 4 seconds, and it sometimes you can't even load a heavy HTML page because the page never finishes. I assume this is most likely because PFSense does not like the onboard NIC, as this is the primary difference between the two servers. It's recognised as NFE0, and there's no room in the server for any more NICs and I don't have any dual-port NICs handy to experiment with a different LAN connection. I've never had to troubleshoot this sort of issue before. Can anyone give me some pointers about where to start? Linux is not my forte so please be kind!

  Read the article

< Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >