Search Results

Search found 5387 results on 216 pages for 'dns sd'.

Page 155/216 | < Previous Page | 151 152 153 154 155 156 157 158 159 160 161 162  | Next Page >

  • Asterisk terminating outbound call when picked up, sends 'BYE' message

    - by vo
    I'm running Asterisk 1.6.1.10 / FreePBX 2.5.2.2 and I've got an outbound trunk setup. Everything use to work fine until recently (perhaps due to upgrade to FC12 or other things I'm not sure). Anyway the setup does not appear to have issues registering and setting up the call, RTP packets go both ways and you can hear the ringing from the other side. However it appears that when the call is picked up or thereabouts, the incoming RTP packets cease. Upon closer inspection with Wireshark, there are these particular packets that seem to be the cause: trunk->asterisk SIP/SD Status: 200 OK, with session description asterisk->trunk SIP Request: ACK sip:<phone>@trunk:6889 asterisk->trunk SIP Request: BYE sip:<phone>@trunk:6889 [..about a dozzen RTP packets in/outbound..] trunk->asterisk SIP Status: 200 OK, CSeq: 104 Bye [..outbound RTP continues, phone is silent..] Then the inbound RTP packets cease, however the asterisk logs dont show any activity at this point. The last entry reads 'SIP/ is answered SIP/'. Then when you hangup the extension, you get asterisk->trunk SIP Request: BYE sip:<phone>@trunk:6889 trunk->asterisk SIP Status: 481 Call Leg/Transaction does not exist My trunk peer settings in FreePBX are: username=<user> fromuser=<user> canreinvite=no type=friend secret=<pass> qualify=no [qualify yes produces 401/forbidden messages] nat=yes insecure=very host=<sip trunk gateway> fromdomain=<sip trunk gateway> disallow=all context=from-pstn allow=ulaw dtmfmode=inband Under sip_general_custom.conf i have stunaddr=stun.xten.com externrefresh=120 localnet=192.168.1.1/255.255.255.0 nat=yes Whats causing Asterisk to prematurely end the call and still think the call is in progress? I have no idea where to look next.

    Read the article

  • PXE Boot not working

    - by Nishant
    Please explain the error in this screenshot DHCP Setting: This screenshot was taken after powering off the old comp hence he server interface is shown as the wireless card - it becomes 192.168.0.1 when I connect wires and power up the old laptop to boot via PXE. My scenario is simple. An old laptop and a new laptop . A cross over cable ( that I myself made from CAT 6 cable by cutting it and connecting 4 wires as mentioned in some doc). The new laptop ( tftp server ) has a Wirelss Card ( with which I am browsing and writing this ) . And the cable is connected between laptops . TFTP server ( new laptop details ) Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::f511:3d4a:ca01:122e%16 IPv4 Address. . . . . . . . . . . : 192.168.0.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.2 Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Achilles Link-local IPv6 Address . . . . . : fe80::99b1:8ae0:9e6c:f300%11 IPv4 Address. . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.2.1

    Read the article

  • newsubtitles line not working in FFmpeg

    - by godMode
    i'm trying to run the following line on FFmpeg that will basically "re-format" an MKV file to MP4 without doing any re-encoding and also embed SRT subtitles onto the MP4 output: ffmpeg -i test.mkv -i test.srt -newsubtitle -acodec copy -vcodec copy test.mp4 Without the "-i test.srt -nwesubtitle" bit, it seems to work just fine; however, with it I get the following output: Seems stream 0 codec frame rate differs from container frame rate: 47.95 (5000000/104271) - 23.98 (24000/1001) Stream #0.0(eng): Video: h264, yuv420p, 1280x720 [PAR 1:1 DAR 16:9], 23.98 fps, 23.98 tbr, 1k tbn, 47.95 tbc Stream #0.1(eng): Subtitle: 0x0000 Metadata: title : English Stream #0.2(jpn): Audio: aac, 48000 Hz, stereo, s16 Metadata: title : Japanese 2.0 Stream #0.3(eng): Audio: aac, 48000 Hz, stereo, s16 Metadata: title : English 2.0 Stream #0.4(eng): Subtitle: 0x0000 Metadata: title : English Songs & Signs Stream #0.5: Attachment: 0x0000 Metadata: filename : MyriadPro-Bold.ttf Stream #0.6: Attachment: 0x0000 Metadata: filename : MyriadPro-RegularHaruhi.ttf Stream #0.7: Attachment: 0x0000 Metadata: filename : ChaparralPro-BoldIt.ttf Stream #0.8: Attachment: 0x0000 Metadata: filename : ChaparralPro-SemiboldIt.ttf Stream #0.9: Attachment: 0x0000 Metadata: filename : epmgobld_ending.ttf Stream #0.10: Attachment: 0x0000 Metadata: filename : epminbld_opening.ttf Stream #0.11: Attachment: 0x0000 Metadata: filename : Folks-Bold.ttf Stream #0.12: Attachment: 0x0000 Metadata: filename : GosmickSansBold.ttf Stream #0.13: Attachment: 0x0000 Metadata: filename : WarnockPro-LightDisp.ttf Stream #0.14: Attachment: 0x0000 Metadata: filename : epmgobld_ending.ttf Stream #0.15: Attachment: 0x0000 Metadata: filename : GosmickSansBold.ttf Stream #0.16: Attachment: 0x0000 Metadata: filename : Marker SD 1.2.ttf Stream #0.17: Attachment: 0x0000 Metadata: filename : MyriadPro-Bold.ttf Stream #0.18: Attachment: 0x0000 Metadata: filename : MyriadPro-RegularHaruhi.ttf Stream #0.19: Attachment: 0x0000 Metadata: filename : MyriadPro-SemiCn.ttf test.srt: Invalid data found when processing input I tried adding "-r pal", "-r ntsc" or "-r 23.98" thinking it was framerate issue with no change.

    Read the article

  • Successful login with iscsiadm on target still doesn't create block device

    - by Halfgaar
    I've set up an experiment to test iscsitarget and initiator, which at some point worked. Later, I turned the setup back on and much to my dismay, the initiator machine stopped making block devices for its successful logins. As far as I know, I haven't changed anything on either machine. Some details: # iscsiadm -m node --login Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260] Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260] Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260]: successful Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260]: successful Sessions: # iscsiadm -m session tcp: [3] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun1 tcp: [4] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun2 Netstat: # netstat -n -p|grep 3260 tcp 0 0 10.0.0.2:48719 10.0.0.1:3260 ESTABLISHED 1078/iscsid tcp 0 0 10.0.0.2:48718 10.0.0.1:3260 ESTABLISHED 1078/iscsid /var/log/syslog doesn't give errors: Jan 27 11:41:49 vmnode001 kernel: [ 378.041749] scsi7 : iSCSI Initiator over TCP/IP Jan 27 11:41:49 vmnode001 kernel: [ 378.044180] scsi8 : iSCSI Initiator over TCP/IP lsscsi doesn't show my devices: [0:0:1:0] cd/dvd TSSTcorp DVD-ROM TS-L333A D100 /dev/sr0 [4:0:0:0] disk ATA Hitachi HUA72105 A74A - [4:0:1:0] disk ATA Hitachi HUA72105 A74A - [4:1:0:0] disk Dell VIRTUAL DISK 1028 /dev/sda And there are no block devices in /dev for it: # ls -1 /dev/sd* /dev/sda /dev/sda1 /dev/sda2 /dev/sda3 /dev/sda4 I tried loading all scsi kernel modules I could find, but that doesn't seem to be the problem. I reall don't get this; it used to work. I found people with similar problems (here and here) but no solution. Initiator is Debian Sqeeuze (testing), target is Debian Lenny (stable). iscsitarget is 0.4.16+svn162-3.1+lenny1, open-iscsi (initiator) is 2.0.871.3-2squeeze1. Target kernel: 2.6.26-2-amd64, initiator kernel: 2.6.32-5-amd64

    Read the article

  • Simple Cisco ASA 5505 config issue

    - by Ben Sebborn
    I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

    Read the article

  • apache webserver unresponsible with server-status showing all child processes waiting for connection

    - by Jeff
    My setup: i have 3 nearly identical webserver machines serving the same high loaded dynamic website with simple load balancing over dns. The service has been working for over two ears with the same apache config. apache2, php5, ubuntu 8.04 linux 2.6.24-29-server My problem: since about two weeks i'm experiencing problems with this config. Nearly every day i have one small moment about 5 minutes, in which the website is unreachable. I'm still able to login to the servers over ssh. If i run htop, i see the machine simply doing nothing. i have about 1000 apache processes running, but no cpu activity. i've used the apache mod_status to debug this situation. the process scoreboard looks like this: _C.___K_______________________R._______.__K_K____K___C_______.__ _______C__________.___________________________________.________C _.____K__________K___K_WK_____._K_____________________________._ W______K__________K________.____________________._______C_______ _C_.__K__K____.._.._____________________________________C_______ _R___________K___.______C________.C_________.______._____C______ ____________KKC____K_____K__WC_________________C_____.__.____.__ _____________________C_________K______.____C______._____________ _.___C____.___.___________________________.K______.____K________ W__.___________________C.__.____K________K_______R_._.__._______ __C__C_.__________C__C_______._____W______________C_.___C_______ ____.______C_____________C________.____C____________.________._K __.__________.K_____________K_________._____C____.K__________KW_ __K.W________R_________._______.___W___________.____.__K_____W__ W___.___..________W____K Scoreboard Key: "_" Waiting for Connection, "S" Starting up, "R" Reading Request, "W" Sending Reply, "K" Keepalive (read), "D" DNS Lookup, "C" Closing connection, "L" Logging, "G" Gracefully finishing, "I" Idle cleanup of worker, "." Open slot with no current process So the most of the processes are just waiting for connection. after about 5 minutes the situation will return to normal: i have lot least processes on every machine, the most workers have the "."-status (meaing they are open to process a request) and of course the website is reachable! so i'm trying to find something in the logs, but there is simply nothing... the apache access log is silent for about 4 minutes, the same is for the error log. i also can not figure out anything wrong in other system logs. the situation is the same on all 3 webservers (all of them have this load peak and unresposibility at the same time), so i do not thing this is hardware related. but i think, this might be related to some network (tcp) issue. any ideas? EDIT: some more information, that i have just discovered: it has just happened again. and i was able to verify that i'm also not able to connect locally when this problem occurs. i have made some connection statistics with the following command after it happend netstat -an|awk '/tcp/ {print $6}'|sort|uniq -c 109 CLOSE_WAIT 2652 ESTABLISHED 2 FIN_WAIT1 11 LAST_ACK 12 LISTEN 91 SYN_RECV 1 SYN_SENT 16 TIME_WAIT If i execute the same command some time later, i have something like this: 4 CLOSING 108 ESTABLISHED 18 FIN_WAIT1 182 FIN_WAIT2 37 LAST_ACK 12 LISTEN 50 SYN_RECV 11276 TIME_WAIT So in the normal situation i have only 100-200 open connections by clients beeing handled by apache in this moment. when i have this "crash", i have a lot more connections. what is the best way to analyse this? EDIT2: the important lines in apache2.conf are: KeepAlive On MaxKeepAliveRequests 20 KeepAliveTimeout 1 <IfModule mpm_prefork_module> ServerLimit 920 StartServers 30 MinSpareServers 80 MaxSpareServers 120 MaxClients 920 MaxRequestsPerChild 700 </IfModule> it is an apache2 prefork with php_mod. the server has 8GB ram and a 4gb swap partition.

    Read the article

  • Performance: Nginx SSL slowness or just SSL slowness in general?

    - by Mauvis Ledford
    I have an Amazon Web Services setup with an Apache instance behind Nginx with Nginx handling SSL and serving everything but the .php pages. In my ApacheBench tests I'm seeing this for my most expensive API call (which cache via Memcached): 100 concurrent calls to API call (http): 115ms (median) 260ms (max) 100 concurrent calls to API call (https): 6.1s (median) 11.9s (max) I've done a bit of research, disabled the most expensive SSL ciphers and enabled SSL caching (I know it doesn't help in this particular test.) Can you tell me why my SSL is taking so long? I've set up a massive EC2 server with 8CPUs and even applying consistent load to it only brings it up to 50% total CPU. I have 8 Nginx workers set and a bunch of Apache. Currently this whole setup is on one EC2 box but I plan to split it up and load balance it. There have been a few questions on this topic but none of those answers (disable expensive ciphers, cache ssl, seem to do anything.) Sample results below: $ ab -k -n 100 -c 100 https://URL This is ApacheBench, Version 2.3 <$Revision: 655654 $> Copyright 1996 Adam Twiss, Zeus Technology Ltd, http://www.zeustech.net/ Licensed to The Apache Software Foundation, http://www.apache.org/ Benchmarking URL.com (be patient).....done Server Software: nginx/1.0.15 Server Hostname: URL.com Server Port: 443 SSL/TLS Protocol: TLSv1/SSLv3,AES256-SHA,2048,256 Document Path: /PATH Document Length: 73142 bytes Concurrency Level: 100 Time taken for tests: 12.204 seconds Complete requests: 100 Failed requests: 0 Write errors: 0 Keep-Alive requests: 0 Total transferred: 7351097 bytes HTML transferred: 7314200 bytes Requests per second: 8.19 [#/sec] (mean) Time per request: 12203.589 [ms] (mean) Time per request: 122.036 [ms] (mean, across all concurrent requests) Transfer rate: 588.25 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 65 168 64.1 162 268 Processing: 385 6096 3438.6 6199 11928 Waiting: 379 6091 3438.5 6194 11923 Total: 449 6264 3476.4 6323 12196 Percentage of the requests served within a certain time (ms) 50% 6323 66% 8244 75% 9321 80% 9919 90% 11119 95% 11720 98% 12076 99% 12196 100% 12196 (longest request)

    Read the article

  • How to find my VPN client IP in windows

    - by cateof
    When I run ipconfig and I get the following: C:\Documents and Settings\grmsrh14>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 112.25.2.222 Subnet Mask . . . . . . . . . . . : 255.255.254.0 Default Gateway . . . . . . . . . : 112.25.2.1 DHCP Class ID . . . . . . . . . . : rise Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected PPP adapter my_lab: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.2.251.41 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : Is there a command that prints only the my_lab(VPN) IP address, ie 10.2.251.41?

    Read the article

  • Yahoo is sending our server's transactional email to the Spam folder, even though we have set up SPF and DKIM

    - by Derrick Miller
    Yahoo Mail is sending our server's transactional emails to the Spam folder, even though we have taken quite a few anti-spam steps. By contrast, Gmail allows the messages through to the inbox just fine. Here are the things which are in place: SPF is set up for the domain holsteinplaza.com. Yahoo reports spf=pass in the message headers. DKIM is set up for the domain holsteinplaza.com. Yahoo reports dkim=pass in the message headers. We have a proper reverse DNS entry for the sending mail server. Name - IP matches IP - Name. Neither Domainkeys nor SenderID are set up. From what I can tell, DKIM is the way of the future, and there is not much to be gained from adding Domainkeys or SenderID. Following are the headers. Any ideas what more I should do to get Yahoo to stop flagging the emails as spam? From Holstein Plaza Auctions Sat Jun 25 18:30:08 2011 X-Apparently-To: [email protected] via 98.138.90.132; Sat, 25 Jun 2011 18:30:11 -0700 Return-Path: <[email protected]> X-YahooFilteredBulk: 70.32.113.42 Received-SPF: pass (domain of holsteinplaza.com designates 70.32.113.42 as permitted sender) X-YMailISG: i_vaA_QWLDuLOmXhDjUv3aBKJl5Un6EiP6Yk2m4yn3jeEuYK MkhpqIt9zDUbHARCwXrhl9pqjTANurGVca7gytSs.mryWVQcbWBx.DaItWRb VcyrIzwMzXKCSeu06H2a.cJ7HG5vJLJaKmHUUI_1ttXKn_Aegiu5yHvFX83R Lpth0witO9zfaKvOMaJV3LAxpIpFOydwvq1cqjZ8nURxQbxM3Cl.QW7MxxrC 09qLVn_D_xSdU94QdU22IsVmlaRHv.uU5dnIazu.KSkhKpYykDoZA2SH0SY4 JmTZj3LP8N926xXVDzYQ5K6QvKuJL5g0d9pYZx3KC59sgIu5oHlJ3Q15RdKb f3OJw0PR6oIyJ2yStVr8vfbDgOfj3qig03.Tw6g6MMNpv1G7Cuol4oJeUaYP xELxX6dHgBgCSuWMcbsrxbK4BIXcS2qhpMqYQ4Isk.XXyA8uvmFXyvgc1ds5 8jo0rW.Wsw.55Z.KTPaQ0gHXj0T3OGppYMELSJv1iuhPyyAnZpmq01CU0Qd5 CcRgdyW3HaqhmpXqJCS0Clo16zXA4HmAjR0tgIQrHRLc3D9N02AOzvmDgCb1 vCh0p00QeKVq8UNkcShPRxZFKi9khtkLhPBlXEKkhJ76zyDmHUxTY.dQHVVD 8D2hx7BxbqI9DINI8x5oR5Q8hYkZqHYQsmGNkaU77O2BnsEv5WxMEmzrBJ4Z h8zGCidgYPiZycZfnfaBp0Xb4tya2WMTN45W02JFcO1qq_UMJ9xPeqZhPEj. j9YvBAC8324GGF.c8eWcNB2VB34QHgTcVUl3.c0XUCuncls9Cyg4L7AoIdCi HvAklSzDDu9nW6732VEipV9FJ_JkDupDNQU2hfiPG.3OeF8GwTnVYnEn0EiZ aO0NCnZhXuLDcN3K7ml3846yRdASvzPFs9s4aJkzR0FkhVvptiMBEOdRkKdG wHWmvWpK4GTZpW4yU7CnKpW2MiWWn1MP0h_CCZFKs5.3mfmfPjPVIABN_RuU Q8ex5hdKnKlQiqK56LzcPRnYmNtrwdsUX9CYn9d6cPpXR_Bi5jrNJMNzdFvq lGO0CBT4QPe2V45U8PtpMitttuDA1cCvmyBPFswxNlL0jyX0a_W.vl0YW5.d HhDItpHhDxKRUscM28IR.exetq4QCzyM X-Originating-IP: [70.32.113.42] Authentication-Results: mta1267.mail.ac4.yahoo.com from=holsteinplaza.com; domainkeys=neutral (no sig); from=holsteinplaza.com; dkim=pass (ok) Received: from 127.0.0.1 (EHLO predator.axis80.com) (70.32.113.42) by mta1267.mail.ac4.yahoo.com with SMTP; Sat, 25 Jun 2011 18:30:11 -0700 Received: (qmail 1440 invoked by uid 48); 25 Jun 2011 21:30:09 -0400 To: [email protected] Subject: this is a test X-PHPMAILER-DKIM: phpmailer.worxware.com DKIM-Signature: v=1; a=rsa-sha1; q=dns/txt; l=203; s=auction; t=1309051808; c=relaxed/simple; h=From:To:Subject; d=holsteinplaza.com; [email protected]; z=From:=20Holstein=20Plaza=20Auctions=20<[email protected]> |To:[email protected] |Subject:=20this=20is=20a=20test; bh=B3Tw5AQb1va627KEoazuFEBZ0fg=; b=oQ5uFq+oekPTGhszyIritjuuIAi3qPNyeitu+aWMhdx3oC6O2j5hJsDFpK0sS5fms7QdnBkBcEzT0iekEvn9EfAdCkGZ2KrtEC0yv7QKQcrjXxy07GJpj9nq0LYbgOuPdw8mGvKxlRZ+jFBX0DRJm0xXFLkr+MEaILw7adHTCCM= Date: Sat, 25 Jun 2011 21:30:08 -0400 From: Holstein Plaza Auctions <[email protected]> Reply-to: Holstein Plaza Auctions <[email protected]> Message-ID: <[email protected]> X-Priority: 3 X-Mailer: PHPMailer 5.1 (phpmailer.sourceforge.net) MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Content-Type: text/plain; charset="iso-8859-1" Content-Length: 195

    Read the article

  • i cant ping to my DMZ zone from the local inside PC

    - by Big Denzel
    HI everybody. Can anyone please help me on the following issue. I got a Cisco Asa 5520 configured at my network. I cant ping to my DMZ interface from a local inside network PC. so the only way a ping the DMZ is right from the Cisco ASA firewall, there i can pint to all 3 interfaces, Inside, Outside and DMZ,,,, But no PC from the Inside Network can access the DMZ. Can please any one help? I thank you all in advance Bellow is my Cisco ASA 5520 Firewall show run; ASA-FW# sh run : Saved : ASA Version 7.0(8) ! hostname ASA-FW enable password encrypted passwd encrypted names dns-guard ! interface GigabitEthernet0/0 description "Link-To-GW-Router" nameif outside security-level 0 ip address 41.223.156.109 255.255.255.248 ! interface GigabitEthernet0/1 description "Link-To-Local-LAN" nameif inside security-level 100 ip address 10.1.4.1 255.255.252.0 ! interface GigabitEthernet0/2 description "Link-To-DMZ" nameif dmz security-level 50 ip address 172.16.16.1 255.255.255.0 ! interface GigabitEthernet0/3 shutdown no nameif no security-level no ip address ! interface Management0/0 description "Local-Management-Interface" no nameif no security-level ip address 192.168.192.1 255.255.255.0 ! ftp mode passive access-list OUT-TO-DMZ extended permit tcp any host 41.223.156.107 eq smtp access-list OUT-TO-DMZ extended permit tcp any host 41.223.156.106 eq www access-list OUT-TO-DMZ extended permit icmp any any log access-list OUT-TO-DMZ extended deny ip any any access-list inside extended permit tcp any any eq pop3 access-list inside extended permit tcp any any eq smtp access-list inside extended permit tcp any any eq ssh access-list inside extended permit tcp any any eq telnet access-list inside extended permit tcp any any eq https access-list inside extended permit udp any any eq domain access-list inside extended permit tcp any any eq domain access-list inside extended permit tcp any any eq www access-list inside extended permit ip any any access-list inside extended permit icmp any any access-list dmz extended permit ip any any access-list dmz extended permit icmp any any access-list cap extended permit ip 10.1.4.0 255.255.252.0 172.16.16.0 255.255.25 5.0 access-list cap extended permit ip 172.16.16.0 255.255.255.0 10.1.4.0 255.255.25 2.0 no pager logging enable logging buffer-size 5000 logging monitor warnings logging trap warnings mtu outside 1500 mtu inside 1500 mtu dmz 1500 no failover asdm image disk0:/asdm-508.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (dmz,outside) tcp 41.223.156.106 www 172.16.16.80 www netmask 255.255.255 .255 static (dmz,outside) tcp 41.223.156.107 smtp 172.16.16.25 smtp netmask 255.255.2 55.255 static (inside,dmz) 10.1.0.0 10.1.16.0 netmask 255.255.252.0 access-group OUT-TO-DMZ in interface outside access-group inside in interface inside access-group dmz in interface dmz route outside 0.0.0.0 0.0.0.0 41.223.156.108 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute http server enable http 10.1.4.0 255.255.252.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh timeout 5 console timeout 0 management-access inside ! ! match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect dns maximum-length 512 inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! service-policy global_policy global Cryptochecksum: : end ASA-FW# Please Help. Big Denzel

    Read the article

  • How to best tune my SAN/Initiators for best performance?

    - by Disco
    Recent owner of a Dell PowerVault MD3600i i'm experiencing some weird results. I have a dedicated 24x 10GbE Switch (PowerConnect 8024), setup to jumbo frames 9K. The MD3600 has 2 RAID controllers, each has 2x 10GbE ethernet nics. There's nothing else on the switch; one VLAN for SAN traffic. Here's my multipath.conf defaults { udev_dir /dev polling_interval 5 selector "round-robin 0" path_grouping_policy multibus getuid_callout "/sbin/scsi_id -g -u -s /block/%n" prio_callout none path_checker readsector0 rr_min_io 100 max_fds 8192 rr_weight priorities failback immediate no_path_retry fail user_friendly_names yes # prio rdac } blacklist { device { vendor "*" product "Universal Xport" } # devnode "^sd[a-z]" } devices { device { vendor "DELL" product "MD36xxi" path_grouping_policy group_by_prio prio rdac # polling_interval 5 path_checker rdac path_selector "round-robin 0" hardware_handler "1 rdac" failback immediate features "2 pg_init_retries 50" no_path_retry 30 rr_min_io 100 prio_callout "/sbin/mpath_prio_rdac /dev/%n" } } And iscsid.conf : node.startup = automatic node.session.timeo.replacement_timeout = 15 node.conn[0].timeo.login_timeout = 15 node.conn[0].timeo.logout_timeout = 15 node.conn[0].timeo.noop_out_interval = 5 node.conn[0].timeo.noop_out_timeout = 10 node.session.iscsi.InitialR2T = No node.session.iscsi.ImmediateData = Yes node.session.iscsi.FirstBurstLength = 262144 node.session.iscsi.MaxBurstLength = 16776192 node.conn[0].iscsi.MaxRecvDataSegmentLength = 262144 After my tests; i can barely come to 200 Mb/s read/write. Should I expect more than that ? Providing it has dual 10 GbE my thoughts where to come around the 400 Mb/s. Any ideas ? Guidelines ? Troubleshooting tips ?

    Read the article

  • Juniper’s Network Connect ncsvc on Linux: “host checker failed, error 10”

    - by hfs
    I’m trying to log in to a Juniper VPN with Network Connect from a headless Linux client. I followed the instructions and used the script from http://mad-scientist.us/juniper.html. When running the script with --nogui switch the command that gets finally executed is $HOME/.juniper_networks/network_connect/ncsvc -h HOST -u USER -r REALM -f $HOME/.vpn.default.crt. I get asked for the password, a line “Connecting to…” is printed but then the programm silently stops. When adding -L 5 (most verbose logging) to the command line, these are the last messages printed to the log: dsclient.info state: kStateCacheCleaner (dsclient.cpp:280) dsclient.info --> POST /dana-na/cc/ccupdate.cgi (authenticate.cpp:162) http_connection.para Entering state_start_connection (http_connection.cpp:282) http_connection.para Entering state_continue_connection (http_connection.cpp:299) http_connection.para Entering state_ssl_connect (http_connection.cpp:468) dsssl.para SSL connect ssl=0x833e568/sd=4 connection using cipher RC4-MD5 (DSSSLSock.cpp:656) http_connection.para Returning DSHTTP_COMPLETE from state_ssl_connect (http_connection.cpp:476) DSHttp.debug state_reading_response_body - copying 0 buffered bytes (http_requester.cpp:800) DSHttp.debug state_reading_response_body - recv'd 0 bytes data (http_requester.cpp:833) dsclient.info <-- 200 (authenticate.cpp:194) dsclient.error state host checker failed, error 10 (dsclient.cpp:282) ncapp.error Failed to authenticate with IVE. Error 10 (ncsvc.cpp:197) dsncuiapi.para DsNcUiApi::~DsNcUiApi (dsncuiapi.cpp:72) What does host checker failed mean? How can I find out what it tried to check and what failed? The HostChecker Configuration Guide mentions that a $HOME/.juniper_networks/tncc.jar gets installed on Linux, but my installation contains no such file. From that I concluded that HostChecker is disabled for my VPN on Linux? Are the POST to /dana-na/cc/ccupdate.cgi and “host checker failed” connected or independent? By running the connection over a SSL proxy I found out that the POST data is status=NOTOK (Funny side note: the client of the oh-so-secure VPN does not validate the server’s SSL certificate, so is wide open to MITM attacks…). So it seems that it’s the client that closes the connection and not the server.

    Read the article

  • lvm mirroring space unavailable.

    - by Bryan Ward
    I am trying to migrate my data on lvm to two new disks, and setup mirroring between the two. I have successfully migrated all of the data to the first of the two disks, leaving the second one completely available as a mirror. I verified this using pvdisplay -m /dev/sd{g,h}1 --- Physical volume --- PV Name /dev/sdg1 VG Name vg PV Size 931.51 GiB / not usable 3.19 MiB Allocatable yes PE Size 4.00 MiB Total PE 238466 Free PE 82866 Allocated PE 155600 PV UUID v2nc3j-EFBR-QpuG-xgro-Rm59-fmu6-IB3QcR --- Physical Segments --- Physical extent 0 to 49999: Logical volume /dev/vg/videos Logical extents 0 to 49999 Physical extent 50000 to 99999: Logical volume /dev/vg/home Logical extents 0 to 49999 Physical extent 100000 to 129999: Logical volume /dev/vg/music Logical extents 0 to 29999 Physical extent 130000 to 155599: Logical volume /dev/vg/videos Logical extents 50000 to 75599 Physical extent 155600 to 238465: FREE --- Physical volume --- PV Name /dev/sdh1 VG Name vg PV Size 931.51 GiB / not usable 3.19 MiB Allocatable yes PE Size 4.00 MiB Total PE 238466 Free PE 238466 Allocated PE 0 PV UUID LuTrem-WcsZ-qw7l-2CDS-lLKI-wdq0-QEXhLf --- Physical Segments --- Physical extent 0 to 238465: FREE Then when I try to mirror the home logical volume for example, it says that I do not have sufficient space. I used lvconvert -m1 vg/home and the output was: Insufficient suitable allocatable extents for logical volume : 50000 more required Unable to allocate extents for mirror(s). This puzzling to me because it appears as if there is plenty of space on the second disk to mirror. Is there something I have done wrong here? Or is there a way to explicitly tell LVM where to put each leg of the mirror? I'm using lvm2.

    Read the article

  • Openvpn issue with linux

    - by catsy
    So I've tried to setup openvpn, I followed some guide but it's stuck att "initialization sequence completed" with no connection and I can't find any working solution... here's the log: $Sun Sep 23 19:14:32 2012 OpenVPN 2.1.0 i486-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 20 2010 Enter Auth Username:pumpedup Enter Auth Password: Sun Sep 23 19:14:37 2012 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Sun Sep 23 19:14:37 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Sun Sep 23 19:14:37 2012 LZO compression initialized Sun Sep 23 19:14:37 2012 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Sun Sep 23 19:14:38 2012 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Sun Sep 23 19:14:38 2012 Local Options hash (VER=V4): '41690919' Sun Sep 23 19:14:38 2012 Expected Remote Options hash (VER=V4): '530fdded' Sun Sep 23 19:14:38 2012 Socket Buffers: R=[163840-131072] S=[163840-131072] Sun Sep 23 19:14:38 2012 UDPv4 link local: [undef] Sun Sep 23 19:14:38 2012 UDPv4 link remote: [AF_INET]192.162.102.162:1194 Sun Sep 23 19:14:38 2012 TLS: Initial packet from [AF_INET]192.162.102.162:1194, sid=87a95723 a6d7b7f9 Sun Sep 23 19:14:38 2012 WARNING: this configuration may cache passwords in memory -- use the auth-nocache option to prevent this Sun Sep 23 19:14:38 2012 VERIFY OK: depth=1, /C=NV/ST=NV/L=nVPN/O=nVpn/CN=nVpn_CA/[email protected] Sun Sep 23 19:14:38 2012 VERIFY OK: depth=0, /C=NV/ST=NV/L=nVPN/O=nVpn/CN=server/[email protected] Sun Sep 23 19:14:39 2012 WARNING: 'link-mtu' is used inconsistently, local='link-mtu 1542', remote='link-mtu 6042' Sun Sep 23 19:14:39 2012 WARNING: 'tun-mtu' is used inconsistently, local='tun-mtu 1500', remote='tun-mtu 6000' Sun Sep 23 19:14:39 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Sun Sep 23 19:14:39 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sun Sep 23 19:14:39 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Sun Sep 23 19:14:39 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sun Sep 23 19:14:39 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Sun Sep 23 19:14:39 2012 [server] Peer Connection Initiated with [AF_INET]192.162.102.162:1194 Sun Sep 23 19:14:41 2012 SENT CONTROL [server]: 'PUSH_REQUEST' (status=1) Sun Sep 23 19:14:41 2012 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1,dhcp-option DNS 8.8.8.8,dhcp-option DNS 8.8.8.8,route 10.102.162.1,topology net30,ping 10,ping-restart 120,ifconfig 10.102.162.6 10.102.162.5' Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: timers and/or timeouts modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: --ifconfig/up options modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: route options modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified Sun Sep 23 19:14:41 2012 ROUTE default_gateway=10.0.2.2 Sun Sep 23 19:14:41 2012 TUN/TAP device tun0 opened Sun Sep 23 19:14:41 2012 TUN/TAP TX queue length set to 100 Sun Sep 23 19:14:41 2012 /sbin/ifconfig tun0 10.102.162.6 pointopoint 10.102.162.5 mtu 1500 Sun Sep 23 19:14:41 2012 /sbin/route add -net 192.162.102.162 netmask 255.255.255.255 gw 10.0.2.2 Sun Sep 23 19:14:41 2012 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 /sbin/route add -net 10.102.162.1 netmask 255.255.255.255 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 Initialization Sequence Completed

    Read the article

  • Bridging a non-persistent PPP connection to wireless (or wired) in Windows XP

    - by phooze
    I have a 3G modem-like device (eMobile's D01NX, PC card style, for any Japan nerds out there) that I use to connect my PC to the Internet. I'd like to bridge this connection with another computer either via an ad-hoc wireless network, or a simple cross-over cable (either are options). However, when I open "Network Connections", I do not see the PPP connection (otherwise I could click both and bridge). I believe this is because there is software (provided by the vendor) that is handling the card directly and registering a PPP connection dynamically. When connected, an ipconfig at the command line yields: Ethernet adapter wireless: Connection-specific DNS Suffix . : Autoconfiguration IP Address. . . : 169.254.5.169 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Ethernet adapter lan: Media State . . . . . . . . . . . : Media disconnected PPP adapter {B59EEDDE-A22B-48DF-93E5-04842B641257}: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 114.xx.xxx.xx Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 114.xx.xxx.xx (I've commented out my IP address for privacy reasons, but what does appear there is a functional Internet IP address.) When I disconnect the adapter with the vendor software, the PPP connection disappears completely from the ipconfig list. Any ideas on how to do this?

    Read the article

  • What is the best server or Ip address to use for prolonged testing?

    - by eldorel
    I usually run uptime/latency tests against (and from) two servers that we own at different sites and until recently I've used the google dns servers as a control group. However, I've realized there is a potential problem with monitoring latency over extended periods of time. Almost all of the major service providers are using ANYCAST. For short tests this doesn't matter, but I need to run a set of tests for at least a week to try and catch an intermittent problem, and a change in the anycast priority while trying to test latency will cause the latency values for that server to change accordingly. Since I'm submitting graphs of this data to the ISP, I need to avoid/account for as many variables as possible. Spikes in the data for only one of the tested servers will only cause headaches. So can anyone recommend servers that: are not using anycast are owned by an entity that has a good uptime reputation (so they can't claim that the problem is server-side) will respond to ICMP requests Have an available service that runs on TCP/UDP (http or dns preferably) Wont consider an automated request every 10 minutes to be abuse Are accessible from anywhere in the world Are not local to the isp ( consider this an investigation of a hostile party ) Thanks in advance. Edit: added #6 and #7 above. More info: I am attempting to demonstrate a network problem for an entire node of our local ISP's network. They are actively blaming the issue on the equipment installed at the customer sites (our backup site is one of these), and refuse to escalate the problem. (even though 2 of these businesses have ISP provided modems, and all of us have completely different routers/services running) I am already quite familiar with the need to test an isp controlled IP, but they are actively dropping all packets targeted at gateway ip addresses and are only passing traffic addressed beyond the gateways. So to demonstrate the issue, I am sending packets to other systems in the same node, systems one hop away from the affected node, and systems completely outside the network. Unfortunately, all of the systems I have currently are either administered directly by myself, or by people who are biased enough to assist me. I need to have several systems included in the trace/log/graphs that are 100% not in the control of either myself or the isp so that the graphs have a stable/unbiased control group. These requirements are straight from legal, I'm just trying to make sure that everything that could be argued to invalidate the data is already covered. In Summary: I need to be able to show tcp/udp/icmp as 3 separate data points, and I need to be able to show the connections inside the local node, from local node to another nearby node, from those 2 nodes to the internet, and through the internet to both verifiable servers and a control group that I have no control over whatsoever. Again, Google/opendns/yahoo/msn/facebook/etc all use anycast, which throws the numbers off every time the anycast caches expire, so I need suggestions of an IP or server that is available for this type of testing. I was hoping someone knew of a system run by someone such as ISC or ICANN, or perhaps even a .gov server (fcc or nsa maybe?) setup for this type of testing. Thanks again.

    Read the article

  • Postfix not sending/allowing receiving of messages after server (hardware) changed

    - by 537mfb
    We had na old notebook runing Ubuntu 12.04 working as a web/ftp/mail server and it worked but since the notebook was a notebook and pretty old and unreliable, a desktop was bought to replace it before it stopped working all together. Due to issues with the new desktop's vídeo card, we couldn't use Ubuntu 12.04 so we installed Ubuntu 13.10 and wen't about configuring it. Since we removed the notebook from the network, we kept the same Computer Name and local IP address to make things as close to the old server as possible configuration-wise. However, something has gone wrong since Postfix is throwing error 451 4.3.0 lookup faillure on every attempt to send a mail, and no email can be received either. Our main.cf file is a copy of the one we were using (and working) on the old server (notice we use EHCP) # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name powered by Easy Hosting Control Panel (ehcp) on Ubuntu, www.ehcp.net biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no myhostname = m21-traducoes.com.pt relayhost = mydestination = localhost, 89.152.248.139 mynetworks = 127.0.0.0/8, 192.168.0.0/16, 172.16.0.0/16, 10.0.0.0/8, 89.152.248.0/24 virtual_alias_domains = virtual_alias_maps = proxy:mysql:/etc/postfix/mysql-virtual_forwardings.cf, proxy:mysql:/etc/postfix/mysql-virtual_email2email.cf transport_maps = proxy:mysql:/etc/postfix/mysql-virtual_transports.cf virtual_mailbox_domains = proxy:mysql:/etc/postfix/mysql-virtual_domains.cf virtual_mailbox_maps = proxy:mysql:/etc/postfix/mysql-virtual_mailboxes.cf virtual_mailbox_base = /home/vmail virtual_uid_maps = static:5000 virtual_gid_maps = static:5000 smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_mynetworks,permit_sasl_authenticated,check_client_access hash:/var/lib/pop-before-smtp/hosts,reject_unauth_destination smtp_use_tls = yes smtpd_use_tls = yes smtpd_tls_auth_only = no smtpd_tls_CAfile = /etc/postfix/cacert.pem smtpd_tls_cert_file = /etc/postfix/smtpd.cert smtpd_tls_key_file = /etc/postfix/smtpd.key smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom virtual_create_maildirsize = yes virtual_mailbox_extended = yes virtual_mailbox_limit_maps = proxy:mysql:/etc/postfix/mysql-virtual_mailbox_limit_maps.cf virtual_mailbox_limit_override = yes virtual_maildir_limit_message = "The user you are trying to reach is over quota." virtual_overquota_bounce = yes debug_peer_list = sender_canonical_maps = debug_peer_level = 1 proxy_read_maps = $local_recipient_maps $mydestination $virtual_alias_maps $virtual_alias_domains $virtual_mailbox_maps $virtual_mailbox_domains $relay_recipient_maps $canonical_maps $sender_canonical_maps $recipient_canonical_maps $relocated_maps $mynetworks $virtual_mailbox_limit_maps $transport_maps alias_maps = hash:/etc/aliases smtpd_relay_restrictions = permit_mynetworks, permit_sasl_authenticated,check_client_access hash:/var/lib/pop-before-smtp/hosts,reject_unauth_destination smtpd_destination_concurrency_limit = 2 smtpd_destination_rate_delay = 1s smtpd_extra_recipient_limit = 10 disable_vrfy_command = yes smtpd_delay_reject = yes smtpd_helo_required = yes smtpd_error_sleep_time = 1s smtpd_soft_error_limit = 10 smtpd_hard_error_limit = 20 This configuration was working before but now everytime i try to send a mail in squirrelmail it reports: Message not sent. Server replied: Requested action aborted: error in processing 451 4.3.0 <[email protected]>: Temporary lookup failure And i can't send mail to it from outsider either. Any ideas? EDIT: Here are some issues MXToolBox reports to my domain, answering hopefully to @Teun Vink: BlackList Mail Server Web Server DNS Error 4 0 2 0 Warnings 0 0 0 3 Passed 0 6 3 12 So the domain is on some blacklist, but that doesn't explain the error at all No mail server issues found (except it's not working) Those two web server errors it's because i don't have HTTPS workin (No SSL Certificate) so the test fails Those 3 DNS warnings we're already there when it was working with the other machine and are related to stuff i can't control: SOA Refresh Value is outside of the recommended range SOA Expire Value out of recommended range SOA NXDOMAIN Value too high I've searched and as far as i can tell only the guys who sold the retail can change those values and they won't. Edit2: I half solved the issue.on the new machine postfix was installed but postfix-mysql waasn't so he couldn't connect to the database (rookie mistake). After fixing that, i can now send mails to the outsider without any issues, however i am still not able to receive mails from utside. The sender doesn't get any message warning about the non-delivery but the message doesn't fall in the inbox and the log shows: Nov 13 15:11:57 m21-traducoes postfix/smtpd[5872]: NOQUEUE: reject: RCPT from re lay4.ptmail.sapo.pt[212.55.154.24]: 451 4.3.5 <relay4.ptmail.sapo.pt[212.55.154. 24]>: Client host rejected: Server configuration error; from=<[email protected]> to=<[email protected]> proto=SMTP helo=<sapo.pt> Nov 13 15:11:57 m21-traducoes postfix/smtpd[5872]: disconnect from relay4.ptmail .sapo.pt[212.55.154.24]

    Read the article

  • IRC server connecting to another server

    - by Oxinabox
    I'm setting up an IRC server using IRC-Hybrid, I want my server to connect to another server, so that people on my server can connect to channels on that other server. I know this can be done, the GIMP IRC, is the same as the GNOME IRC My ircd.conf contains the following: connect { name = "aabstractname"; host = "128.64.2.1; send_password = "somepass"; accept_password = "somepass"; encrypted = no; port = 6667; class = "server"; autoconn = yes; compressed = yes; fakename = "irc.sd.dom.asn.au"; }; So when i run: /etc/init.d/ircd-hybrid restart it should be connecting to 128.64.2.1, but the log on 128.64.2.1, doesn't show anything Do I need entry on the host 128.64.2.1? I can't find any documentation for ircd.conf I'ld really like that documentation so I can check all my settings are right.

    Read the article

  • How to use a different Ethernet connection

    - by SteveC
    I'm running a virtual machine at home which has a VPN connection to our main office, but I also want to connect to a share on another machine at home. When I check with IPCONFIG I can see two ethernet connections ... my work VPN ... Ethernet adapter Local Area Connection* 11: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : xxxx::xxxx:xxxx:xxxx:xxxxxxx IPv4 Address. . . . . . . . . . . : XXX.XXX.XXX.XXX Subnet Mask . . . . . . . . . . . : 255.255.254.0 Default Gateway . . . . . . . . . : XXX.XXX.XXX.XXX and home local ... Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : lan Link-local IPv6 Address . . . . . : xxxx::xxxx:xxxx:xxxx:xxxxxxx IPv4 Address. . . . . . . . . . . : 192.168.1.70 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : What's weird is when I've been working before with a plugged-in ethernet cable I've not had any problem getting to the share? I can PING the other machine, but I can't access the share at ... \\othermachine\c$ I tried 'TRACERT` but that disappears off to the work network and eventually gets back to the local other machine after a few time-outs Is there anyway to "force" the connection to stay local ? UPDATE: the VPN is AEP SSL Tunnel

    Read the article

  • How to use Public IP in case of two ISP when two differs from each other

    - by user1471995
    Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

    Read the article

  • Improve wireless performance

    - by djechelon
    Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

    Read the article

  • Linux usd disk just create sg device

    - by MTilsted
    I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata).

    Read the article

  • Apache https is slsow

    - by raucous12
    Hey, I've set apache up to use SSL with a self signed certificate. With http (KeepAlive off), I can get over 5000 requests per second. However, with https, I can only get 13 requests per second. I know there is supposed to be a bit of an overhead, but this seems abnormal. Can anyone suggest how I might go about debugging this. Here is the ab log for https: Server Software: Apache/2.2.3 Server Hostname: 127.0.0.1 Server Port: 443 SSL/TLS Protocol: TLSv1/SSLv3,DHE-RSA-AES256-SHA,4096,256 Document Path: /hello.html Document Length: 29 bytes Concurrency Level: 5 Time taken for tests: 30.49425 seconds Complete requests: 411 Failed requests: 0 Write errors: 0 Total transferred: 119601 bytes HTML transferred: 11919 bytes Requests per second: 13.68 [#/sec] (mean) Time per request: 365.565 [ms] (mean) Time per request: 73.113 [ms] (mean, across all concurrent requests) Transfer rate: 3.86 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 190 347 74.3 333 716 Processing: 0 14 24.0 1 166 Waiting: 0 11 21.6 0 165 Total: 191 361 80.8 345 716 Percentage of the requests served within a certain time (ms) 50% 345 66% 377 75% 408 80% 421 90% 468 95% 521 98% 578 99% 596 100% 716 (longest request)

    Read the article

  • How long will a "safely stored" Solid-State-Drive (SSD) keep its data? (e.g. bank safety-deposit box)

    - by user31575
    Here's my usecase: once-and-only-once copy off photos/videos to an internal SATA Solid State Drive (SSD) put this drive in a well-ventilated, air-conditioned bank "safety deposit box" for safe keeping The question: How long can I safely store a solid-state-drive in such an environment? i.e. 0% bitrot, 100% success when "plugged in" Are some SSD drives more reliable than other for this usecase? (e.g. smaller size vs larger size, SLC vs MLC, different brands, etc) More fodder: I have read that solid state memory cards (e..g compactflash, or sd cards) have much longer durability than other media (DVD's, CD's, hard drives) for this usecase (guaranteed against bitrot/other dysfunction on the order of ~ a decades vs a year ). I don't know if this applies to "SSD hard drives". Copying to one 500Gb ssd vs 8 64gb flash drives is easier SSD SATA hard drives have no moving parts, but they have more "visible electronics" than a compact flash card. I don't know if this "visible electronics" can fail, i.e. in contr I know many will point to carbonite, other cloud backup stuff, but I like the simplicity of having physical copies and wanted to understand the risks/implications thanks,

    Read the article

  • Removing a device in "removed" state from Linux software RAID array

    - by Sahasranaman MS
    My workstation has two disks(/dev/sd[ab]), both with similar partitioning. /dev/sdb failed, and cat /proc/mdstat stopped showing the second sdb partition. I ran mdadm --fail and mdadm --remove for all partitions from the failed disk on the arrays that use them, although all such commands failed with mdadm: set device faulty failed for /dev/sdb2: No such device mdadm: hot remove failed for /dev/sdb2: No such device or address Then I hot swapped the failed disk, partitioned the new disk and added the partitions to the respective arrays. All arrays got rebuilt properly except one, because in /dev/md2, the failed disk doesn't seem to have been removed from the array properly. Because of this, the new partition keeps getting added as a spare to the partition, and its status remains degraded. Here's what mdadm --detail /dev/md2 shows: [root@ldmohanr ~]# mdadm --detail /dev/md2 /dev/md2: Version : 1.1 Creation Time : Tue Dec 27 22:55:14 2011 Raid Level : raid1 Array Size : 52427708 (50.00 GiB 53.69 GB) Used Dev Size : 52427708 (50.00 GiB 53.69 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Intent Bitmap : Internal Update Time : Fri Nov 23 14:59:56 2012 State : active, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Name : ldmohanr.net:2 (local to host ldmohanr.net) UUID : 4483f95d:e485207a:b43c9af2:c37c6df1 Events : 5912611 Number Major Minor RaidDevice State 0 8 2 0 active sync /dev/sda2 1 0 0 1 removed 2 8 18 - spare /dev/sdb2 To remove a disk, mdadm needs a device filename, which was /dev/sdb2 originally, but that no longer refers to device number 1. I need help with removing device number 1 with 'removed' status and making /dev/sdb2 active.

    Read the article

< Previous Page | 151 152 153 154 155 156 157 158 159 160 161 162  | Next Page >