Search Results

Search found 21343 results on 854 pages for 'pass by reference'.

Page 155/854 | < Previous Page | 151 152 153 154 155 156 157 158 159 160 161 162  | Next Page >

• How to bypass resume from hibernate [closed]

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• apache2 + mod_fastcgi + suexec + php5.2 = unstable on high load...

  - by redguy..pl

  I am hosting several (~30) different sites on one server with apache2+fastcgi+suexec+php5. Sites have different loads and different execution times of their scripts (some of them process request for 5-7 seconds, some <1sek). Sometimes when single site receives very high load (all php instances of this site are created and used) - whole apache server hangs. Apache (worker mpm) creates new processes up to the upper limit. It looks like it is starting to queue ALL new request for EVERY site, not only the one that has high load and quickly achieves process limits... restart of apache solves the problem... config: FastCgiConfig -singleThreshold 1 -multiThreshold 10 -listen-queue-depth 30 -maxProcesses 80 -maxClassProcesses 12 -idle-timeout 30 -pass-header HTTP_AUTHORIZATION -pass-header If-Modified-Since -pass-header If-None-Match (earlier have default -listen-queue-depth = 100, but it didn't change anything...) Any suggestions? Another question - how is implemented this listen queue? is it one queue for whole apache, or unique queue for every defined php apllication (suexec site)? I would like to achieve something like this: when one site receives high load and its queue is full - server bounces next request, but only for this one site.. Other sites should work properly...

  Read the article

• BizTalk configuration broken following WCF hotfix installation

  - by Sir Crispalot

  I usually post over on StackOverflow, but thought this was probably better suited to ServerFault. Please migrate if I'm wrong! I am developing a WCF service and a BizTalk application on my workstation at the moment. As part of the WCF service, I had to install hotfix 971493 from Microsoft which updates some core WCF assemblies. Following installation of that hotfix, I am now experiencing severe issues in my existing BizTalk application. When I attempt to configure the properties of an existing WCF-Custom receive location, I get this error: Error loading properties (System.IO.FileLoadException) The located assembly's manifest definition does not match the assembly reference. (Exception from HRESULT: 0x80131040) If I click OK (the same error repeats four times) I eventually see the WCF-Custom properties dialog. However if I click on the various tabs, I continue to receive errors: The located assembly's manifest definition does not match the assembly reference. (Exception from HRESULT: 0x80131040) (Microsoft.BizTalk.Adapter.Wcf.Admin) The WCF-Custom receive location was working yesterday, and I installed the hotfix this morning. I'm guessing these two are related, and that BizTalk somehow has a reference to the old WCF assemblies. Does anyone know how I can fix this?

  Read the article

• OpenVPN: ERROR: could not read Auth username from stdin

  - by user56231

  I managed to setup openvpn but now I want to integrate a user/pass authentication method so, even though I haven't added the auth-nocache in the server config, whenever I try to connect it returns with the following message on the client side: ERROR: could not read Auth username from stdin My server.conf file contains basic stuff, everything works up untill I try to implement this for of authentication. mode server dev tun proto tcp port 1194 keepalive 10 120 plugin /usr/lib/openvpn/openvpn-auth-pam.so login client-cert-not-required username-as-common-name auth-user-pass-verify /etc/openvpn/auth.pl via-env ca /etc/openvpn/easy-rsa/2.0/keys/ca.crt cert /etc/openvpn/easy-rsa/2.0/keys/server.crt key /etc/openvpn/easy-rsa/2.0/keys/server.key dh /etc/openvpn/easy-rsa/2.0/keys/dh1024.pem user nobody group nogroup server 10.8.0.0 255.255.255.0 persist-key persist-tun #persist-local-ip status openvpn-status.log verb 3 client-to-client push "redirect-gateway def1" push "dhcp-option DNS 10.8.0.1" log-append /var/log/openvpn comp-lzo I searched all over the net for a solution and all answers seems to be related to the auth-nocache param which I haven't set. The directive auth-user-pass-verify /etc/openvpn/auth.pl via-env points to a script which is executed to perform the authentication. A false authentication should result in a exit 1 while a true one should result with exit 0. For testing, that script auth.pl returns exit 0 no matter what the input is but it seems that the file is not executed before the error raises. auth.pl file contents: #!/usr/bin/perl my $user = $ENV{username}; my $passwd = $ENV{password}; printf("$user : $passwd\n"); exit 0; Any ideas?

  Read the article

• Rundeck get verbose output of command executing on node

  - by Leon Stafford

  I have Rundeck executing a remote script, which is in python is using print statements to return output normally such as: $ python mytest.py PASS: Condition 1 passed PASS: Condition 2 passed PASS: and so on... When I run this via Rundeck, however, it doesn't show me the same print generated outputs as above. In Rundeck's most detailed Debug output mode, I only receive the following: 06:31:12 Permanently added 'myremotenode.com' (RSA) to the list of known hosts. 06:31:12 SSH_MSG_NEWKEYS sent 06:31:12 SSH_MSG_NEWKEYS received 06:31:12 SSH_MSG_SERVICE_REQUEST sent 06:31:13 SSH_MSG_SERVICE_ACCEPT received 06:31:13 Authentications that can continue: publickey,password,keyboard-interactive 06:31:13 Next authentication method: publickey 06:31:13 Authentication succeeded (publickey). 06:31:13 /cygdrive/c/Program Files (x86)/Mozil... 06:32:06 Adding reference: ant.PropertyHelper 06:32:06 Setting project property: sshexec.output -> /cygdrive/c/Prog... I know that the remote script is actually executing just as usual, as I'm receiving other emails generated by the ~30min long script. Obviously, I don't want to have to wait 30mins to see the result of each print statement within the python script. How can I get the same level of output in Rundeck as I do in the bash shell directly?

  Read the article

• OpenBSD logins via SSH seem to be ignoring my configured radius server

  - by Steve Kemp

  I've installed and configured a radius server upon my localhost - it is delegating auth to a remote LDAP server. Initially things look good: I can test via the console: # export user=skemp # export pass=xxx # radtest $user $pass localhost 1812 $secret Sending Access-Request of id 185 to 127.0.0.1 port 1812 User-Name = "skemp" User-Password = "xxx" NAS-IP-Address = 192.168.1.168 NAS-Port = 1812 rad_recv: Access-Accept packet from host 127.0.0.1 port 1812, id=185, Similarly I can use the login tool to do the same thing: bash-4.0# /usr/libexec/auth/login_radius -d -s login $user radius Password: $pass authorize However remote logins via SSH are failing, and so are invokations of "login" started by root. Looking at /var/log/radiusd.log I see no actual log of success/failure which I do see when using either of the previous tools. Instead sshd is just logging: sshd[23938]: Failed publickey for skemp from 192.168.1.9 sshd[23938]: Failed keyboard-interactive for skemp from 192.168.1.9 port 36259 ssh2 sshd[23938]: Failed password for skemp from 192.168.1.9 port 36259 ssh2 In /etc/login.conf I have this: # Default allowed authentication styles auth-defaults:auth=radius: ... radius:\ :auth=radius:\ :radius-server=localhost:\ :radius-port=1812:\ :radius-timeout=1:\ :radius-retries=5:

  Read the article

• How flexible is the 'indirect' function?

  - by Chuck

  My curiosity pushes me to ask this question. If I were to have a series of functions that referenced a different column in a worksheet but all ended on the same row of data is there a way to point the 'row' part of a cell reference to a blank cell and use it has a variable to show the results of the functions up to a desired row simultaneously? Example: =Average('worksheet 1'.$A$1:'worksheet 1'.$A100) =Max('worksheet 1'.$B$1:'worksheet 1'.$B100) =Min('worksheet 1'.$C$1:'worksheet 1'.$C100) =Sum('worksheet 1'.$D$1:'worksheet 1'.$D100) Pseudo formulas... =Average('worksheet 1'.$A$1:'worksheet 1'.$A*('worksheet 2'.$A$1)*) =Max('worksheet 1'.$B$1:'worksheet 1'.$B*('worksheet 2'.$A$1)*) =Min('worksheet 1'.$C$1:'worksheet 1'.$C*('worksheet 2'.$A$1)*) =Sum('worksheet 1'.$D$1:'worksheet 1'.$D*('worksheet 2'.$A$1)*) Where 'worksheet 2'.$A$1 would only contain a number corresponding to a row in 'worksheet 1'. After stumbling upon and playing with the indirect() function I have only been able to replace the entire cell reference (Column and Row) with any success. The formula so far =SUM('worksheet 1'.C3:INDIRECT(A1)) Where A1 is on 'worksheet 2' and contains a full cell reference pointing to 'worksheet 1'. Any pointers?

  Read the article

• Passing two arguments to a command using pipes

  - by firebat

  Usually, we only need to pass one argument: echo abc | cat echo abc | cat some_file - echo abc | cat - some_file Is there a way to pass two arguments? Something like {echo abc , echo xyz} | cat cat `echo abc` `echo xyz` I could just store both results in a file first echo abc > file1 echo xyz > file2 cat file1 file2 But then I might accidentally overwrite a file, which is not ok. This is going into a non-interactive script. Basically, I need a way to pass the results of two arbitrary commands to cat without writing to a file. UPDATE: Sorry, the example masks the problem. While { echo abc ; echo xyz ; } | cat does seem to work, the output is due to the echos, not the cat. A better example would be { cut -f2 -d, file1; cut -f1 -d, file2; } | paste -d, which does not work as expected. With file1: a,b c,d file2: 1,2 3,4 Expected output is: b,1 d,3 RESOLVED: Use process substitution: cat <(command1) <(command2) Alternatively, make named pipes using mkfifo: mkfifo temp1 mkfifo temp2 command1 > temp1 & command2 > temp2 & cat temp1 temp2 Less elegant and more verbose, but works fine, as long as you make sure temp1 and temp2 don't exist before hand.

  Read the article

• apache2 + mod_fastcgi + suexec + php5.2 = unstable on high load

  I am hosting several (~30) different sites on one server with apache2+fastcgi+suexec+php5. Sites have different loads and different execution times of their scripts (some of them process request for 5-7 seconds, some <1sek). Sometimes when single site receives very high load (all php instances of this site are created and used) - whole apache server hangs. Apache (worker mpm) creates new processes up to the upper limit. It looks like it is starting to queue ALL new request for EVERY site, not only the one that has high load and quickly achieves process limits... restart of apache solves the problem... config: FastCgiConfig -singleThreshold 1 -multiThreshold 10 -listen-queue-depth 30 -maxProcesses 80 -maxClassProcesses 12 -idle-timeout 30 -pass-header HTTP_AUTHORIZATION -pass-header If-Modified-Since -pass-header If-None-Match (earlier have default -listen-queue-depth = 100, but it didn't change anything...) Any suggestions? Another question - how is implemented this listen queue? is it one queue for whole apache, or unique queue for every defined php apllication (suexec site)? I would like to achieve something like this: when one site receives high load and its queue is full - server bounces next request, but only for this one site.. Other sites should work properly...

  Read the article

• Hudson deploy specific git revision

  - by brad

  I'm using hudson to auto-deploy my Rails app to heroku. In my main build job I pull from a Git repo (hosted using gitosis on the same machine), master branch with the following: URL of repository: /home/git/repositories/my_app.git Name of repository: origin Refspec: +refs/heads/master:refs/remotes/origin/master Branches to build: master Then, assuming all tests pass, I want to kick off a new build that is the deploy to Heroku. I can't however figure out how to get that deploy build to checkout the particular revision that this build was using. I understand there's a parameterized trigger plugin that would allow me to pass this revision number, but I don't know how I can tell hudson to checkout this particular revision on the deploy build. I'm pretty sure this just has to do with my limited knowledge of git, but where in the hudson git config's is there an option to checkout a particular revision? Otherwise, I could have many commits happen whilst a build is happening, and when it kicks off a deploy build, that deploy build would just check out the HEAD of the branch, which may not be the same as the code that was pushed that triggered this build. I don't fully understand why I have a refspec in Hudson, then also specify a branch to build, I thought this was the same thing. Can refspec somehow specify the revision number? How would this be referenced if it was passed through with the parameterized trigger plugin? (I've never used that plugin, but someone else recommended it as a way to pass in vars to a new build, if there's another way I'm all ears)

  Read the article

• Prevent outgoing traffic unless OpenVPN connection is active using pf.conf on Mac OS X

  - by Nick

  I've been able to deny all connections to external networks unless my OpenVPN connection is active using pf.conf. However, I lose Wi-Fi connectivity if the connection is broken by closing and opening the laptop lid or toggling Wi-Fi off and on again. I'm on Mac OS 10.8.1. I connect to the Web via Wi-Fi (from varying locations, including Internet cafés). The OpenVPN connection is set up with Viscosity. I have the following packet filter rules set up in /etc/pf.conf # Deny all packets unless they pass through the OpenVPN connection wifi=en1 vpn=tun0 block all set skip on lo pass on $wifi proto udp to [OpenVPN server IP address] port 443 pass on $vpn I start the packet filter service with sudo pfctl -e and load the new rules with sudo pfctl -f /etc/pf.conf. I have also edited /System/Library/LaunchDaemons/com.apple.pfctl.plist and changed the line <string>-f</string> to read <string>-ef</string> so that the packet filter launches at system startup. This all seems to works great at first: applications can only connect to the web if the OpenVPN connection is active, so I'm never leaking data over an insecure connection. But, if I close and reopen my laptop lid or turn Wi-Fi off and on again, the Wi-Fi connection is lost, and I see an exclamation mark in the Wi-Fi icon in the status bar. Clicking the Wi-Fi icon shows an "Alert: No Internet connection" message: To regain the connection, I have to disconnect and reconnect Wi-Fi, sometimes five or six times, before the "Alert: No Internet connection" message disappears and I'm able to open the VPN connection again. Other times, the Wi-Fi alert disappears of its own accord, the exclamation mark clears, and I'm able to connect again. Either way, it can take five minutes or more to get a connection again, which can be frustrating. Why does Wi-Fi report "No internet connection" after losing connectivity, and how can I diagnose this issue and fix it?

  Read the article

• virtual memory commited

  - by vinu

  After a server bounce happens, and after around 40-45 days time period, we receive continuous “Committed Virtual Memory” alerts which indicates the usage of swap space in the magnitude of 4GB This also causes the application to perform very slowly and experience a number of stalled transactions. Server Setup: 4 Tomcat Servers (version 7.0.22) that are load balanced (not clustered) by 2 Apache Servers. And the Apache servers themselves supply static content and routing to these 4 tomcat servers. Java Runtime Version: java version "1.6.0_30" Java(TM) SE Runtime Environment (build 1.6.0_30-b12) Java HotSpot(TM) 64-Bit Server VM (build 20.5-b03, mixed mode Memory Startup Parameters: MEMORY_OPTIONS="-Xms1024m -Xmx1024m -Xss192k -XX:MaxGCPauseMillis=500 -XX:+HeapDumpOnOutOfMemoryError -XX:MaxPermSize=256m -XX:+CMSClassUnloadingEnabled" Monitoring – Wily monitoring is available in all the production servers that monitors key server parameters and sends out configurable alert emails based on pre defined settings. Note: Each of the servers also has two other separate tomcat domains that run different applications Investigated area: There is no Heap Memory Leak and the GC is running fine without any issues over any period of time The current busy thread count corresponds directly to the application usage – weekends and nights have lesser no. of threads compared to business hours ThreadLocal uses a WeakReference internally. If the ThreadLocal is not strongly referenced, it will be garbage-collected, even though various threads have values stored via that ThreadLocal. Additionally, ThreadLocal values are actually stored in the Thread; if a thread dies, all of the values associated with that thread through a ThreadLocal are collected. If you have a ThreadLocal as a final class member, that's a strong reference, and it cannot be collected until the class is unloaded. But this is how any class member works, and isn't considered a memory leak. The cited problem only comes into play when the value stored in a ThreadLocal strongly references that ThreadLocal—sort of a circular reference. In this case, the value (a SimpleDateFormat), has no backwards reference to the ThreadLocal. There's no memory leak in this code. Can anyone please let me know what could be the cause of this and what to be monitored?

  Read the article

• Nginx > Varnish > Gunicorn Error Too many Redirections

  - by kollo

  I have the following config: Nginx Varnish Gunicorn Django I want to cache 2 versions of same site (mobile & web) with Varnish. Gunicorn : WEB: gunicorn_django --bind 127.0.0.1:8181 MOBILE: gunicorn_django --bind 127.0.0.1:8182 Nginx: WEB: server { listen 80; server_name www.mysite.com; location / { proxy_pass http://127.0.0.1:8282; # pass to Varnish proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } MOBILE: server { listen 80; server_name m.mysite.com; location / { proxy_pass http://127.0.0.1:8282; # pass to Varnish proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } Varnish: default.vcl backend mobile_mysite { .host = "127.0.0.1"; .port = "8182"; } backend mysite { .host = "127.0.0.1"; .port = "8181"; } sub vcl_recv { if (req.http.host ~ "(?i)^(m.)?mysite.com$") { set req.http.host = "m.mysite.com"; set req.backend = mobile_mysite; }elsif (req.http.host ~ "(?i)^(www.)?mysite.com$") { set req.http.host = "mysite.com"; set req.backend = mysite; } if (req.url ~ ".*/static") { /* do not cache static content */ return (pass); } } The problem: On Nginx if I setup Mobile version with Varnish (port 8282) and let WEB version with Gunicorn( port 8181), MOBILE is cached by varnish, both WEB & MOBILE works but WEB is not cached. If I set the proxy_pass of WEB version to Varnish (port 8282) and restart Nginx I got an error when accessing web version (www.mysite.com) "Too many redirections" . I Think my problem come from the Varnish config file, as the site works well if I setup Nginx proxy_pass to Gunicorn ports (MOBILE & WEB).

  Read the article

• Varnish returning 503, FetchError (could not get storage)

  - by Archan

  On the current setup we're running into a problem with Varnish, we're running a CentOS 5.7 x86_64 xenpv, with Cpanel WHM, hosted at VPS.net. Sometimes we will recieve a Guru Meditation from Varnish, and when we look in the varnishlog with the following command varnishlog -d -c -m TxStatus:503 it returns output similar to the following: 15 VCL_call c recv 15 VCL_acl c NO_MATCH devs 15 VCL_return c pass 15 VCL_call c hash 15 Hash c **** 15 Hash c ************* 15 VCL_return c hash 15 VCL_call c pass pass 15 Backend c 12 default default 15 TTL c 1835862523 RFC 0 -1 -1 1332454056 0 1332454055 375007920 0 15 VCL_call c fetch hit_for_pass 15 ObjProtocol c HTTP/1.1 15 ObjResponse c OK 15 ObjHeader c Date: Thu, 22 Mar 2012 22:07:35 GMT 15 ObjHeader c Server: Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/0.9.8e-fips-rhel5 mod_bwlimited/1.4 mod_fcgid/2.3.6 15 ObjHeader c X-Powered-By: PHP/5.3.9 15 ObjHeader c Expires: Thu, 19 Nov 1981 08:52:00 GMT 15 ObjHeader c Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 15 ObjHeader c Pragma: no-cache 15 ObjHeader c Content-Type: text/html; charset=utf-8 15 ObjHeader c X-Cacheable: NO:Cache-Control=private 15 FetchError c chunked read_error: 12 (Could not get storage) 15 VCL_call c error deliver 15 VCL_call c deliver deliver As far as I have could gather, we could try increasing the nuke_limit, but currently we have a nuke_limit of 500, and when running varnishstat -1 -f n_lru_nuked we "only" get a total of 1031, even though we have seen the error happen on several pages. When we then run top to see how much memory Varnish is using, it only shows that it is using 763m, although we've set it to be allowed to use 1200m. Any ideas of what the problem can be?

  Read the article

• Doing arithmetic and passing it to the next command

  - by neurolysis

  I know how to do this in /bin/sh, but I'm struggling a bit in Windows. I know you can do arithmetic on 32-bit signed integers with SET /a 2+2 4 But how do I pass this to the next command? For example, the process I want to perform is as follows. Consumer editions of Windows have no native automated sleep function (I believe?) -- the best way to perform a sleep is to use PING in association with the -n switch to get that many seconds, minus one, of sleep. The following command is effective for a silent sleep: PING localhost -n 3 > NUL But I want to alias this into a sleep command. I'd like to have it elegant so that you enter the actual number of seconds you want to sleep after the command, right now I can do DOSKEY SLEEP=PING 127.0.0.1 -n $1 > NUL Which works, but it's always 1 second less than your input, so if you wanted to sleep for one second you would have to use the command SLEEP 2. That's not exactly ideal. Is there some way for me to pass the arithmetic of $1+1 and pass it on to the next command in Windows? I assume there is some way of using STDOUT...

  Read the article

• Is there any way to distribute x264 encoding jobs across multiple computers (to increase the encoding speed)?

  - by Breakthrough

  Does anyone know of a current, active solution to encoding x264 videos across many computers (via the network) to increase encoding FPS? Brownie points for cross-platform and open source, but just so you all know, I usually use Windows. Programs that I have heard of, and why I do not believe they are suitable: x264farm: Not actively developed. Good interface, but does not support two-pass encoding, and fails with newer x264 builds. ELDER: Again, not actively developed, but my issue was that it didn't work with new x264 builds, and it was very difficult to configure (read: randomly stopped working). While I don't absolutely need a program which is being actively developed, I would like one that supports two-pass encoding, and works with new(er) x264 builds. Additional information: So far, I've offered (and awarded!) two separate bounties on this question since I first posted it over two years ago, and I still haven't found a solution to this problem. What I'm looking for basically is a simple program to allow me to encode x264 videos using the processing power of multiple computers connected over a LAN. Furthermore, it would be nice if it worked with new(er) x264 builds, and supported two-pass encoding. If at any time someone has an updated answer, or a new solution to this problem, please post it and it will be given some consideration.

  Read the article

• Can't get php+sqlite working

  - by facha

  Hi, everyone I'm struggling all morning to make php work with an sqlite database. Here is a piece of php code that I try to execute: #less /var/www/html/test.php <?php $db=new PDO("sqlite:/var/www/test.sql"); $sql = "insert into test (login,pass) values ('login','pass');"; $db->exec($sql); ?> Here is how I've done tests: # sqlite3 /var/www/test.sql sqlite> create table test (login varchar,pass varchar); #chown apache:apache /var/www/test.sql #chmod 644 /var/www/test.sql Here is the stuff that drives me mad: When I execute from command line: #php test.php everything goes well. Sql is being executed and I can see a new row appear in the database. When I execute the same script from a browser - sql is not being executed. I don't get a new row in the database. There are no errors in the apache log file. Please, help

  Read the article

• How to connect to DB2 when the password ends with '!' in Windows

  - by AngocA

  I am facing a problem to use the DB2 tools when using generic account with a generated password which ends with the Bang sign '!' to connect to DB2 database. I am not allowed to change the password because it is already used by other processes. I know the user is valid and I can connect to the database with its credentials, but not from all db2 tools. When using the Control Center it is okay. When using the Command Editor (GUI) or the Command Windows, I got this error message: connect to WAREHOUS user administrator using ! SQL0104N An unexpected token "!" was found following "<identifier>". Expected tokens may include: "NEW". SQLSTATE=42601 Let's say that my password is: pass@! I am trying to use c:\>db2 connect to sample user administrator using "pass@!" or c:\>db2 connect to sample user administrator using pass@! And it both cases I got the same error message. I could change the way I connect but it is not useful for me, for example: c:\>db2 connect to sample user administrator Enter current password for administrator: But I cannot use it from a batch file easily. I would like to know how can I connect from the Command Editor, in order to use this user from the Graphical Tools. BTW, I know that the Control Center is deprecated.

  Read the article

• Multiple SSL certificates on one server

  - by Kyle O'Brien

  We're hosting two websites on our fairly tiny but dedicated production server. Both website require SSL authentication. So, we have virtualhosts set up for both of them. They both reference their own domain.key, domain.crt and domain.intermediate.crt files. Each CSR and certificate file for each site was setup using its own unique information and nothing is shared between them (other than the server itself) However, which ever site's symbolic link (set up in /etc/apache2/sites-enabled) is reference first, is the site who's certificate is referenced even if we're visiting the second site. So for example, assume our companies are Cadbury and Nestle. We set up both sites with their own certificates but we create Cadbury's symbolic link in apache's site-enabled folder first and then Nestle's. You can visit Nestle perfectly fine but if you check the certificate installation, it reference's Cadbury's certificate. We're hosting these websites on a dedicated Ubuntu 12.04.3 LTS server. Both certificates are provided by Thawte.com. I came across a few potential solutions with no degree of success. I'm hoping someone else has a decent solution? Thanks Edit: The only other solution that seems to have provided success to some people is using SNI with Apache. However, the setups here didn't seem to coincide with our setup at all.

  Read the article

• How to resovle javax.mail.AuthenticationFailedException issue?

  - by jl

  Hi, I am doing a sendMail Servlet with JavaMail. I have javax.mail.AuthenticationFailedException on my output. Can anyone please help me out? Thanks. sendMailServlet code: try { String host = "smtp.gmail.com"; String from = "[email protected]"; String pass = "pass"; Properties props = System.getProperties(); props.put("mail.smtp.starttls.enable", "true"); props.put("mail.smtp.host", host); props.put("mail.smtp.user", from); props.put("mail.smtp.password", pass); props.put("mail.smtp.port", "587"); props.put("mail.smtp.auth", "true"); props.put("mail.debug", "true"); Session session = Session.getDefaultInstance(props, null); MimeMessage message = new MimeMessage(session); Address fromAddress = new InternetAddress(from); Address toAddress = new InternetAddress("[email protected]"); message.setFrom(fromAddress); message.setRecipient(Message.RecipientType.TO, toAddress); message.setSubject("Testing JavaMail"); message.setText("Welcome to JavaMail"); Transport transport = session.getTransport("smtp"); transport.connect(host, from, pass); message.saveChanges(); Transport.send(message); transport.close(); }catch(Exception ex){ out.println("<html><head></head><body>"); out.println("ERROR: " + ex); out.println("</body></html>"); } Output on GlassFish 2.1: DEBUG SMTP: trying to connect to host "smtp.gmail.com", port 587, isSSL false 220 mx.google.com ESMTP 36sm10907668yxh.13 DEBUG SMTP: connected to host "smtp.gmail.com", port: 587 EHLO platform-4cfaca 250-mx.google.com at your service, [203.126.159.130] 250-SIZE 35651584 250-8BITMIME 250-STARTTLS 250-ENHANCEDSTATUSCODES 250 PIPELINING DEBUG SMTP: Found extension "SIZE", arg "35651584" DEBUG SMTP: Found extension "8BITMIME", arg "" DEBUG SMTP: Found extension "STARTTLS", arg "" DEBUG SMTP: Found extension "ENHANCEDSTATUSCODES", arg "" DEBUG SMTP: Found extension "PIPELINING", arg "" STARTTLS 220 2.0.0 Ready to start TLS EHLO platform-4cfaca 250-mx.google.com at your service, [203.126.159.130] 250-SIZE 35651584 250-8BITMIME 250-AUTH LOGIN PLAIN 250-ENHANCEDSTATUSCODES 250 PIPELINING DEBUG SMTP: Found extension "SIZE", arg "35651584" DEBUG SMTP: Found extension "8BITMIME", arg "" DEBUG SMTP: Found extension "AUTH", arg "LOGIN PLAIN" DEBUG SMTP: Found extension "ENHANCEDSTATUSCODES", arg "" DEBUG SMTP: Found extension "PIPELINING", arg "" DEBUG SMTP: Attempt to authenticate AUTH LOGIN 334 VXNlcm5hbWU6 aWpveWNlbGVvbmdAZ21haWwuY29t 334 UGFzc3dvcmQ6 MTIzNDU2Nzhf 235 2.7.0 Accepted DEBUG: getProvider() returning javax.mail.Provider[TRANSPORT,smtp,com.sun.mail.smtp.SMTPTransport,Sun Microsystems, Inc] DEBUG SMTP: useEhlo true, useAuth true

  Read the article

• Jquery and live act wired but act ok after force refresh in IE

  - by Y.G.J

  hi guys - somthing is wrong with my code and i can't get what it is... i have a div id = "personaltab" i have a form in side it to login the user with username and password. if success the jquery empty the div and puts in the form of the bidding. if the user try to bid the other ajax that assign to the button is working but for some reason skips the empty and just adding the responded ajax to the div i have checked that in IE and chrome and it is working fine in chrome here are my codes $("#login").click(function() { var id = $("input#pid").val(); var user = $("input#puser").val(); var pass = $("input#ppass").val(); var dataString = 'id='+ id + '&user='+ user + '&pass=' + pass; if (user == "") { alert("error"); $("input#puser").focus(); return false; } if (pass == "") { alert("error"); $("input#ppass").focus(); return false; } $.ajax({ type: "POST", url: "loginpersonal.asp", data: dataString, success: function(msg) { if (msg=="False") { alert("error"); $("#personaltab").show(); } else { $("#personaltab").fadeOut("normal",function(){ $("#personaltab").empty(); $("#personaltab").append(msg); $("#personaltab").slideDown(); }); } }, error: function (XMLHttpRequest, textStatus, errorThrown) { alert('error'); } }); return false; }); $("#sendbid").live("click", function(){ var startat = $("input[name=startat]").val(); var sprice = $("input[name=sprice]").val(); if (parseInt(sprice)<=parseInt(startat)) { alert("error"); $("input[name=sprice]").focus(); return false; } else { var payment = $("select[name=payment]").val(); if ($('input[name=credit]').is(':checked') ){ var credit = true; } var prodid = $("input[name=id]").val(); var dataString = 'id='+ prodid + '&price='+ sprice + '&payment=' + payment + '&credit=' + credit; $.ajax({ type: "POST", url: "loginpersonal.asp", data: dataString, success: function(msg) { $("#personaltab").empty(); $("#personaltab").append(msg); $("#personaltab").show(); }, error: function (XMLHttpRequest, textStatus, errorThrown) { alert('error'); } }); } return false; });

  Read the article

• Please help me understand why my XSL Transform is not transforming

  - by Damovisa

  I'm trying to transform one XML format to another using XSL. Try as I might, I can't seem to get a result. I've hacked away at this for a while now and I've had no success. I'm not even getting any exceptions. I'm going to post the entire code and hopefully someone can help me work out what I've done wrong. I'm aware there are likely to be problems in the xsl I have in terms of selects and matches, but I'm not fussed about that at the moment. The output I'm getting is the input XML without any XML tags. The transformation is simply not occurring. Here's my XML Document: <?xml version="1.0"?> <Transactions> <Account> <PersonalAccount> <AccountNumber>066645621</AccountNumber> <AccountName>A Smith</AccountName> <CurrentBalance>-200125.96</CurrentBalance> <AvailableBalance>0</AvailableBalance> <AccountType>LOAN</AccountType> </PersonalAccount> </Account> <StartDate>2010-03-01T00:00:00</StartDate> <EndDate>2010-03-23T00:00:00</EndDate> <Items> <Transaction> <ErrorNumber>-1</ErrorNumber> <Amount>12000</Amount> <Reference>Transaction 1</Reference> <CreatedDate>0001-01-01T00:00:00</CreatedDate> <EffectiveDate>2010-03-15T00:00:00</EffectiveDate> <IsCredit>true</IsCredit> <Balance>-324000</Balance> </Transaction> <Transaction> <ErrorNumber>-1</ErrorNumber> <Amount>11000</Amount> <Reference>Transaction 2</Reference> <CreatedDate>0001-01-01T00:00:00</CreatedDate> <EffectiveDate>2010-03-14T00:00:00</EffectiveDate> <IsCredit>true</IsCredit> <Balance>-324000</Balance> </Transaction> </Items> </Transactions> Here's my XSLT: <xsl:stylesheet xmlns:xsl="http://www.w3.org/1999/XSL/Transform" version="1.0"> <xsl:output method="xml" /> <xsl:param name="currentdate"></xsl:param> <xsl:template match="Transactions"> <xsl:element name="OFX"> <xsl:element name="SIGNONMSGSRSV1"> <xsl:element name="SONRS"> <xsl:element name="STATUS"> <xsl:element name="CODE">0</xsl:element> <xsl:element name="SEVERITY">INFO</xsl:element> </xsl:element> <xsl:element name="DTSERVER"><xsl:value-of select="$currentdate" /></xsl:element> <xsl:element name="LANGUAGE">ENG</xsl:element> </xsl:element> </xsl:element> <xsl:element name="BANKMSGSRSV1"> <xsl:element name="STMTTRNRS"> <xsl:element name="TRNUID">1</xsl:element> <xsl:element name="STATUS"> <xsl:element name="CODE">0</xsl:element> <xsl:element name="SEVERITY">INFO</xsl:element> </xsl:element> <xsl:element name="STMTRS"> <xsl:element name="CURDEF">AUD</xsl:element> <xsl:element name="BANKACCTFROM"> <xsl:element name="BANKID">RAMS</xsl:element> <xsl:element name="ACCTID"><xsl:value-of select="Account/PersonalAccount/AccountNumber" /></xsl:element> <xsl:element name="ACCTTYPE"><xsl:value-of select="Account/PersonalAccount/AccountType" /></xsl:element> </xsl:element> <xsl:element name="BANKTRANLIST"> <xsl:element name="DTSTART"><xsl:value-of select="StartDate" /></xsl:element> <xsl:element name="DTEND"><xsl:value-of select="EndDate" /></xsl:element> <xsl:for-each select="Items/Transaction"> <xsl:element name="STMTTRN"> <xsl:element name="TRNTYPE"><xsl:choose><xsl:when test="IsCredit">CREDIT</xsl:when><xsl:otherwise>DEBIT</xsl:otherwise></xsl:choose></xsl:element> <xsl:element name="DTPOSTED"><xsl:value-of select="EffectiveDate" /></xsl:element> <xsl:element name="DTUSER"><xsl:value-of select="CreatedDate" /></xsl:element> <xsl:element name="TRNAMT"><xsl:value-of select="Amount" /></xsl:element> <xsl:element name="FITID" /> <xsl:element name="NAME"><xsl:value-of select="Reference" /></xsl:element> <xsl:element name="MEMO"><xsl:value-of select="Reference" /></xsl:element> </xsl:element> </xsl:for-each> </xsl:element> <xsl:element name="LEDGERBAL"> <xsl:element name="BALAMT"><xsl:value-of select="Account/PersonalAccount/CurrentBalance" /></xsl:element> <xsl:element name="DTASOF"><xsl:value-of select="EndDate" /></xsl:element> </xsl:element> </xsl:element> </xsl:element> </xsl:element> </xsl:element> </xsl:template> </xsl:stylesheet> Here's my method to transform my XML: public string TransformToXml(XmlElement xmlElement, Dictionary<string, object> parameters) { string strReturn = ""; // Load the XSLT Document XslCompiledTransform xslt = new XslCompiledTransform(); xslt.Load(xsltFileName); // arguments XsltArgumentList args = new XsltArgumentList(); if (parameters != null && parameters.Count > 0) { foreach (string key in parameters.Keys) { args.AddParam(key, "", parameters[key]); } } //Create a memory stream to write to Stream objStream = new MemoryStream(); // Apply the transform xslt.Transform(xmlElement, args, objStream); objStream.Seek(0, SeekOrigin.Begin); // Read the contents of the stream StreamReader objSR = new StreamReader(objStream); strReturn = objSR.ReadToEnd(); return strReturn; } The contents of strReturn is an XML tag (<?xml version="1.0" encoding="utf-8"?>) followed by a raw dump of the contents of the original XML document, stripped of XML tags. What am I doing wrong here?

  Read the article

• Method Cannot be reflected error

  - by acadia

  Hello, I am trying to add the web reference of a IBM FileNet WebSErvice in my .net application. The only change I did is changed the namespace in the reference from System.Web.Services.Protocols.SoapHttpClientProtocol TO Microsoft.Web.Services3.WebServicesClientProtocol After doing so, though the application is building properly. I am getting an error ExecuteChanges[webMethod] cannot be reflected. Please help

  Read the article

• Reading a POP3 server with only TcpClient and StreamWriter/StreamReader[SOLVED]

  - by WebDevHobo

  I'm trying to read mails from my live.com account, via the POP3 protocol. I've found the the server is pop3.live.com and the port if 995. I'm not planning on using a pre-made library, I'm using NetworkStream and StreamReader/StreamWriter for the job. I need to figure this out. So, any of the answers given here: http://stackoverflow.com/questions/44383/reading-email-using-pop3-in-c are not usefull. It's part of a larger program, but I made a small test to see if it works. Eitherway, i'm not getting anything. Here's the code I'm using, which I think should be correct. EDIT: this code is old, please refer to the second block problem solved. public Program() { string temp = ""; using(TcpClient tc = new TcpClient(new IPEndPoint(IPAddress.Parse("127.0.0.1"),8000))) { tc.Connect("pop3.live.com",995); using(NetworkStream nws = tc.GetStream()) { using(StreamReader sr = new StreamReader(nws)) { using(StreamWriter sw = new StreamWriter(nws)) { sw.WriteLine("USER " + user); sw.Flush(); sw.WriteLine("PASS " + pass); sw.Flush(); sw.WriteLine("LIST"); sw.Flush(); while(temp != ".") { temp += sr.ReadLine(); } } } } } Console.WriteLine(temp); } Visual Studio debugger constantly falls over tc.Connect("pop3.live.com",995); Which throws an "A socket operation was attempted to an unreachable network 65.55.172.253:995" error. So, I'm sending from port 8000 on my machine to port 995, the hotmail pop3 port. And I'm getting nothing, and I'm out of ideas. Second block: Problem was apparently that I didn't write the quit command. The Code: public Program() { string str = string.Empty; string strTemp = string.Empty; using(TcpClient tc = new TcpClient()) { tc.Connect("pop3.live.com",995); using(SslStream sl = new SslStream(tc.GetStream())) { sl.AuthenticateAsClient("pop3.live.com"); using(StreamReader sr = new StreamReader(sl)) { using(StreamWriter sw = new StreamWriter(sl)) { sw.WriteLine("USER " + user); sw.Flush(); sw.WriteLine("PASS " + pass); sw.Flush(); sw.WriteLine("LIST"); sw.Flush(); sw.WriteLine("QUIT "); sw.Flush(); while((strTemp = sr.ReadLine()) != null) { if(strTemp == "." || strTemp.IndexOf("-ERR") != -1) { break; } str += strTemp; } } } } } Console.WriteLine(str); }

  Read the article

• Add Silverlight Bing Maps Control to Windows Mobile 7 application

  - by Jacob

  I know the bits just came out today, but one of the first things I want to do with the newly released Windows Mobile 7 SDK is put a map up on the screen and mess around. I've downloaded the latest version of the Silverlight Maps Control and added the references to my application. As a matter of fact, the VS 2010 design view of the MainPage.xaml shows the map control after adding the namespace and placing the control. I'm using the provided VS 2010 Express version that comes with the Win Mobile 7 SDK and have just used the New Project - Windows Phone Application template. When I try to build I get two warnings related to the Microsoft.Maps.MapControl dll's. Warning 1 The primary reference "Microsoft.Maps.MapControl, Version=1.0.1.0, Culture=neutral, PublicKeyToken=498d0d22d7936b73, processorArchitecture=MSIL" could not be resolved because it has an indirect dependency on the framework assembly "System.Windows.Browser, Version=2.0.5.0, Culture=neutral, PublicKeyToken=7cec85d7bea7798e" which could not be resolved in the currently targeted framework. "Silverlight,Version=v4.0,Profile=WindowsPhone". To resolve this problem, either remove the reference "Microsoft.Maps.MapControl, Version=1.0.1.0, Culture=neutral, PublicKeyToken=498d0d22d7936b73, processorArchitecture=MSIL" or retarget your application to a framework version which contains "System.Windows.Browser, Version=2.0.5.0, Culture=neutral, PublicKeyToken=7cec85d7bea7798e". Warning 2 The primary reference "Microsoft.Maps.MapControl.Common, Version=1.0.1.0, Culture=neutral, PublicKeyToken=498d0d22d7936b73, processorArchitecture=MSIL" could not be resolved because it has an indirect dependency on the framework assembly "System.Windows.Browser, Version=2.0.5.0, Culture=neutral, PublicKeyToken=7cec85d7bea7798e" which could not be resolved in the currently targeted framework. "Silverlight,Version=v4.0,Profile=WindowsPhone". To resolve this problem, either remove the reference "Microsoft.Maps.MapControl.Common, Version=1.0.1.0, Culture=neutral, PublicKeyToken=498d0d22d7936b73, processorArchitecture=MSIL" or retarget your application to a framework version which contains "System.Windows.Browser, Version=2.0.5.0, Culture=neutral, PublicKeyToken=7cec85d7bea7798e". I'm leaning towards some way of adding the System.Windows.Browser to the targeted framework version. But I'm not even sure if that is possible. To be more specific; I'm looking for a way to get the Silverlight Maps Control up on a Windows Phone 7 series application. If possible. Thanks.

  Read the article

< Previous Page | 151 152 153 154 155 156 157 158 159 160 161 162  | Next Page >