Search Results

Search found 5262 results on 211 pages for 'commands'.

Page 156/211 | < Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >

• How to boot Linux from a 16gb USB flash drive

  - by Chris Harris

  I'm trying to install Linux on a single partition of a USB flash drive that's larger than 4gb. The first place I went to is http://pendrivelinux.com. I can follow these instructions for installing Xubuntu 9.04 perfectly, which unfortunately break down when I try to scale it up beyond 4gb. There are several other tools to do this (unetbootin and usb-creator) which follow a very similar formula. I figured out that a big problem of mine was that all of these tools assume the USB drive is formatted in FAT32, which unfortunately cannot hold a single file larger than 4gb. This is unfortunate because I want to use just one partition, so that my persistance file, casper-rw, looks like one big partition to the OS once I've booted off of the USB drive. I then tried following a myriad of instructions involving formatting the drive as one large ext2 filesystem and using extlinux to create a single bootable ext2 file system. This doesn't work for me however, after about 20 attempts verifying and slightly tweaking the formula, I cannot seem to get a "good" bootable ext2 file system built. I'm not entirely sure what's going on, but it seems as though no matter how hard I try, I cannot get the ext2 file system to remain coherent after copying the Linux ISO contents over, copying the MBR, and executing extlinux to create the ext bootloader. Every time, after I follow these steps (in any order) and reboot, I get an unbootable USB drive. If I then mount the drive under Linux again, I see a mess of a file system (inodes have clearly been screwed up somewhere along the way). I suspected that the USB drive wasn't being fully flushed, so I tried using the "sync" and "unmount" commands before rebooting which didn't affect things at all. I guess I have several possible questions - but let's start with the obvious - is there something I'm missing to create a bootable ext2 USB flash drive that's large (e.g. 16gb)?

  Read the article

• best practice to removing DC from Site that no longer connects via vpn in another city

  - by dasko

  hi i am looking for a recap of what i have done already to see if i missed anything. i had two cities connected by wan using a ipsec persistent tunnel between gateways. i had one DC (DOMAIN CONTROLLER) in each city that was a global catalog server (GC) they were set up to replicate and i had them configured under Sites and Servers with their own subnet etc... about 6 months ago the one city was removed and i was not able to gracefully remove, through dcpromo, the server that was there. it is no longer used and cannot be brought back. the company went from two sites down to single site. Problem is i had a whole bunch of kcc errors and replication bugs in the event viewer. i wanted to clean up my active directory and decided to use the ntdsutil metadata cleanup commands. i removed the server from the specifed site based on a procedure from petri website. I then removed the instances of the old DC and site from Sites and Servers. Then i went and cleaned up the DNS by removing Host A records, NS server name from both the local DNS forward lookup zone and the _msdcs i also removed the reverse lookup zone for the subnet that no longer exists. is there anything i missed? thanks in advance for any help. gd

  Read the article

• MultiPath configuration on RHEL5 and Clariion CX-300

  - by Kamil Z

  I have problem with discovering my FC-connected CX-300 storage. Frankly speaking I'm complete novice in FibreChannel, so step by step explanation would be appreciated. My configuration consist of two IBM HS20 blades with RHEL5.4 on board and 2x Qlogic ISP2422-based 4Gb Fibre Channel HBAs on each blade. As a FC switch there are two Brocades built in BladeCenter Chassis, and finally there is EMC Clariion CX-300. CX300, and Brocade switches should be configured properly, because they were working fine with previous configuration, which main defference was RHEL3 instead RHEL5.4 Below there is my output from several usefull commands: #lspci | grep Fibre 06:01.0 FibreChannle: Qlogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA (rev 02) 06:01.1 FibreChannle: Qlogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA (rev 02) #lsmod | grep qla qla2xxx 1084741 0 scsi_transport_fc 37577 1 qla2xxx scsi_mod 141717 10 scsi_dh,qla2xxx,sg,scsi_transport_fc,usb_storage,libata,mptspi,mptscsih,scsi_transport_spi,sd_mod #cat /proc/scsi/scsi Attached Devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: LSILOGIC Model: 1030 IM IM Rev: 1000 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi0 Channel: 01 Id: 00 Lun: 00 Vendor: IBM-ESXS Model: ST936701LC FN Rev: B418 Type: Direct-Access ANSI SCSI revision: 04 Host: scsi0 Channel: 01 Id: 00 Lun: 00 Vendor: IBM-ESXS Model: ST936701LC FN Rev: B418 Type: Direct-Access ANSI SCSI revision: 04 I'd followed instructions from this site (editing /etc/multipath.conf), but i failed after multipath -ll - the output was empty. Do you have any suggestions about discovering FC Connected LUNs in such configuration?

  Read the article

• Migrating Windows XP BOOT.INI Settings to Windows 7 Boot-loader

  - by Synetech inc.

  Two months ago my motherboard died, so I bought a used computer that came with Windows 7. I have since installed my old hard-drive, which had Windows XP on it, in this system. What I am trying to do now is to figure out a way to migrate the settings from XP's BOOT.INI into 7's boot-loader. Below is the BOOT.INI I used in XP (I have reduced the strings and updated the disks to point to the new location of the old HD. Oh and I am not clear on the drive letters. In XP, I could boot the recovery console or MS-DOS from a file in C:\ that contains the boot-sector. I am not sure what drive letter it would be called now—I had to manually change all the drive letters of the old partitions in Windows 7 because it auto-assigned them all wrong/differently). [boot loader] timeout=10 default=multi(0)disk(0)rdisk(1)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP" /fastdetect multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP (Safe)" /safeboot:network /sos /bootlog /noguiboot C:\CMDCONS\BOOTSECT.DAT="Recovery Console" /cmdcons C:\BOOTSECT.DOS="MS-DOS 7.10" /win95 I have looked around, and have only been able to find some bcdedit commands to add XP to the boot-loader, but none that include information on setting safe-mode for it (or changing any of the XP load options for that matter). Not surprisingly I suppose, I have not found anything on adding the XP recovery console or DOS to the Windows 7 boot-loader. (Yes, I tried EasyBCD, but that did not help; it had no options for XP, and the best I managed was to get a choice of booting 7 or normal-mode XP—choosing XP didn't even give the old XP boot menu.) Can anyone please tell me how to export the entries in XP's boot.ini to 7's boot-loader so that on boot, I can choose to load the following: Windows 7 Windows 7 (Safe-mode) (Windows 7 (The Win7 counterpart of the Recovery Console)) Windows XP Windows XP (Safe-mode) Windows XP (Recovery Console) MS-DOS 7.10

  Read the article

• Scheduled tasks fail to start unless I'm logged in to the server

  - by Chuck

  Tasks need to open a CMD window and pass net use commands, then do a DIR command, pipping the output to a file on the server. Log in as either me (Sysadmin) or with one of the system accounts and task will only run if I'm physically logged into the server. Run as batch file is set in security properties for both users (me and service account), security is granted to all directories, etc. It almost acts like a scheduled task, since it is not physically connected to a display can't create a CMD window and pass the WinID so the command can be sent. I'm guessing. Anyone know of a document that explains how the server handles initiation of a window if done via scheduled task and no attached user is associated with the task? If I log onto the box and run the scheduled tasks they run fine, but produce no errors or event log entries and then just show that it ran successfully and sets the next run time. Have tried both with the run if logged in checkbox on and off and makes no difference. Other tasks work fine, except that they are acting on local drives with no display writing or updating taking place, so I'm guessing the system either can't instantiate a window if no display is connected to a logged on user, or it can't establish a point if it is trying to create a virtual screen. You'd think it is just creating a memory map and then mapping it to a device to display, but that doesn't seem to be the case, but I can find no documentation on how the system handles a scheduled task and how to invoke a fake or virtual screen that it could write to so it appears that a user was connected. Thanks This is driving me nuts and I've tried everything I can think of as well as our network boys ideas and nothing seems to work.

  Read the article

• Enable RemoteApp Full Desktop programmatically

  - by Scott Chamberlain

  I am writing a powershell script to set up some HyperV VM's however there is one step I am having trouble automating. How do I check the box to allow Remote desktop access from the RemoteApp settings programmatically? I can set up all of my customizations I need by doing #build the secrity descriptor so the desktop only shows up for people who should be allowed to see it $remoteDesktopUsersSid = New-Object System.Security.Principal.SecurityIdentifier($remoteDesktopUsersGroup.objectSid[0],0) $aceTemplet = 'O:WDG:WDD:ARP(A;CIOI;CCLCSWLORCGR;;;{0})' $securityDescriptor = $aceTemplet -f $remoteDesktopUsersSid #get a copy of the WMI instance $tsRemoteDesktop = Get-WmiObject -Namespace root\CIMV2\TerminalServices -Class Win32_TSRemoteDesktop #set settings $tsRemoteDesktop.Name = $ServerDisplayName $tsRemoteDesktop.SecurityDescriptor = $securityDescriptor $tsRemoteDesktop.IconPath = $IconPath $tsRemoteDesktop.IconIndex = $IconIndex #push settings back to server Set-WmiInstance -InputObject $tsRemoteDesktop -PutType UpdateOnly however the instance of that WMI object does not exist until after you have the above box checked. I attempted to use Set-WmiInstance to instantiate and set the settings at the same time but I keep getting errors like: Set-WmiInstance : At line:53 char:16 + Set-WmiInstance <<<< -Namespace root\CIMV2\TerminalServices -Class Win32_TSRemoteDesktop -Arguments @{Alias='TSRemoteDesktop';Name=$ServerDisplayName;ShowInPortal=$true;SecurityDescriptor=$securityDescriptor} + CategoryInfo : NotSpecified: (:) [Set-WmiInstance], ArgumentException + FullyQualifiedErrorId : System.ArgumentException,Microsoft.PowerShell.Commands.SetWmiInstance (also after running the command and getting the error it will delete the instance of Win32_TSRemoteDesktop if it already exited and un-check the box in the properties setting) Is there any way to programmatically check that box or can anyone help with why Set-WmiInstance throws that error?

  Read the article

• 'pskill \\hostname winlogon' might budge a server "stuck rebooting", but why?

  - by Snoi

  Question: Executing remote (Sysinternals) command... pskill \\machine winlogon ...can budge a server that is stuck rebooting, but how/why does this work? How do you know which service to kill? To recreate (e.g.): You run Windows Update, allow a reboot, and ...NOTHING! RDP gets cut off but the server does not reboot. Just about every other service seems to stay up. Further Background: I've faced this problem on VMs hosted around the planet for some years, and used various sc.exe and shutdown commands to learn the state of and attempt remote reboot of servers in such a state, with limited success. Most datacentres don't offer any way to see the true console or power off/on such machines. They charge $$ for you to call them to do such simple things after hours, when you nearly always have to run your maint tasks. e.g. NET USE \\machine\IPC$ /USER:login password sc \\machine query RpcSs sc \\machine query TermService sc \\machine query wuauserv tasklist /s machine This occasionally works for me... shutdown /m \\machine /r /f /t: 0 ...but more often than not it fails with: A system shutdown is in progress (1115). I found this question, and the answer by @Tweek, and it worked really well, but was I just lucky? Can not RDP to Win 2003 box or initiate remote restart @Tweek said to run: pskill \\hostname winlogon ...and that got me past this situation in a new way (Server 2008 R2 in my most recent case) - really useful! I just need to understand if I got lucky or there is more science here. What I'd like to know is why the winlogon process? @Livne said to use "tasklist /s HostName" to see what is the culprit, but how do you tell from the listed output? It's just a list of running tasks etc. From that I would not know what to look for, nor could I see anything about the winlogon process that suggested to my eyes that was the one to kill.

  Read the article

• ZFS - zpool ARC cache plus L2ARC benchmarking

  - by jemmille

  I have been doing lots of I/O testing on a ZFS system I will eventually use to serve virtual machines. I thought I would try adding SSD's for use as cache to see how much faster I can get the read speed. I also have 24GB of RAM in the machine that acts as ARC. vol0 is 6.4TB and the cache disks are 60GB SSD's. The zvol is as follows: pool: vol0 state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM vol0 ONLINE 0 0 0 c1t8d0 ONLINE 0 0 0 cache c3t5001517958D80533d0 ONLINE 0 0 0 c3t5001517959092566d0 ONLINE 0 0 0 The issue is I'm not seeing any difference with the SSD's installed. I've tried bonnie++ benchmarks and some simple dd commands to write a file then read the file. I have run benchmarks before and after adding the SSD's. I've ensured the file sizes are at least double my RAM so there is no way it can all get cached locally. Am I missing something here? When am I going to see benefits of having all that cache? Am I simply not under these circumstances? Are the benchmark programs not good for testing the effect of cache because of the the way (and what) it writes and reads?

  Read the article

• Preventing Windows version of Vim from destroying other file systems permissions

  - by dborba

  I am currently using the windows version of gVim to edit source files on a networked drive mapped to a linux system, as well as local files created in cygwin. The problem is that the windows version of gVim destroys the original file permissions on the respective systems. IE: Files on cygwin are defaulted to 077. When edited by the windows version of vim they are saved as 777.This problem doesn't even occur when using ms-notepad (as well as all other editors I've tried), so I am not quite sure why gVim does it. A possible solution would be to use cygwin's gVim for everything, but that's rather cumbersome as it requires running an x11 environment to support it, and it causes some problems when running some commands from within gVim (or vim for that matter) when working on the networked drive. Any ideas how I might be able to maintain the existing file permissions? Edit: This morning while on a different machine the problem with cygwin did not occur. Cygwin & gVim were the same version, however the other machine is running WinXP while the machine the problem is occurring on runs Win7.

  Read the article

• Recursive move utility on Unix?

  - by Thomas Vander Stichele

  Sometimes I have two trees that used to have the same content, but have grown out of sync (because I moved disks around or whatever). A good example is a tree where I mirror upstream packages from Fedora. I want to merge those two trees again by moving all of the files from tree1 into tree2. Usually I do this with: rsync -arv tree1/* tree2 Then delete tree1. However, this takes an awful lot of time and disk space, and it would be much easier to be able to do: mv -r tree1/* tree2 In other words, a recursive move. It would be faster because first of all it would not even copy, just move the inodes, and second I wouldn't need a delete at the end. Does this exist ? As a test case, consider the following sequence of commands: $ mkdir -p a/b $ touch a/b/c1 $ rsync -arv a/ a2 sending incremental file list created directory ./ b/ b/c1 b/c2 sent 173 bytes received 57 bytes 460.00 bytes/sec total size is 0 speedup is 0.00 $ touch a/b/c2 What command would now have the effect of moving a/b/c2 to a2/b/c2 and then deleting the a subtree (since everything in it is already in the destination tree) ?

  Read the article

• Get-ChildItem fails to connect in SQLSERVER drive

  - by Norman Kelm

  I'm having some trouble with the SQLSERVER PSDRIVE. See error below. I only have named instances on my PC, both 2005 and 2008 Added the SQL snapins. The PC is named YODA The SQL instance is SQL2008 Navigate to the Databases folder for YODA\SQL2008. You can see the path below. dir -name spits out a connection error trying to connect to YODASQL2008\DEFAULT when it should be trying to connect to YODA\SQL2008. Then it outputs the db name which is Twitter in this case. Is there something missing from my config? Output: PS SQLSERVER:\SQL\YODA\SQL2008\Databases dir -name Get-ChildItem : SQL Server PowerShell provider error: Could not connect to 'YODASQL2008\DEFAULT'. [Failed to connect to server YODASQL2008. -- A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)] At line:1 char:4 + dir <<<< -name + CategoryInfo : OpenError: (SQLSERVER:\SQL\...tabases\Twitter:SqlPath) [Get-ChildItem], GenericProviderException + FullyQualifiedErrorId : ConnectFailed,Microsoft.PowerShell.Commands.GetChildItemCommand Twitter Repeats with error for every database. Thanks, Norman

  Read the article

• Cachefilesd (cachefiles) everything seems to be set up, still not working

  - by Evgenius

  I'm trying to set up cachefilesd to work with my network folder shared using NFS. I have seemingly everything set up, however cachefilesd starts normally, however caching isn't functioning. Here is output of commands, which I ran in the same order 1 sudo mount ... cache-1:/mnt/datashared on /mnt/nfsshare type nfs (rw,sync,ac,acregmin=3,acregmax=60,acdirmin=30,acdirmax=300,lookupcache=pos,vers=3,fsc) ... 2 lsbmod | grep cachefiles cachefiles 40555 1 fscache 57430 4 nfs,cifs,cachefiles,nfsv4 3 [edited - deleted] 4 uname -r 3.8.0-34-generic 5 grep CONFIG_NFS_FSCACHE /boot/config-3.8.0-34-generic CONFIG_NFS_FSCACHE=y 6 lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 13.04 Release: 13.04 Codename: raring 7 sudo service cachefilesd restart * Restarting FilesCache daemon cachefilesd [ OK ] 8 dmesg [6211206.141781] FS-Cache: Withdrawing cache "mycache" [6211210.135236] FS-Cache: Cache "mycache" added (type cachefiles) [6211210.135242] CacheFiles: File cache on sdb1 registered [6214644.348929] CacheFiles: File cache on sdb1 unregistering [6214644.348935] FS-Cache: Withdrawing cache "mycache" [6214654.575909] FS-Cache: Cache "mycache" added (type cachefiles) [6214654.575915] CacheFiles: File cache on sdb1 registered 9 ps aux | grep cachefilesd root 65399 0.0 0.0 4460 540 ? Ss 23:14 0:00 /sbin/cachefilesd 1000 65464 0.0 0.0 8160 916 pts/0 S+ 23:16 0:00 grep --color=auto cachefilesd finally, biggest problem is 10 cat /proc/fs/nfsfs/volumes NV SERVER PORT DEV FSID FSC v3 64476645 801 0:24 233e020f0da07a93 no tl;dr I think I configured everything properly but FSC mount option + fscachefilesd don't seem to work

  Read the article

• NVidia ION and /dev/mapper/nvidia_... issues.

  - by Ritsaert Hornstra

  I have an NVidia ION board with 4 SATA ports and want to use that to run a Linux Server (CentOS 5.4). I first hooed up 3 HDs (that will be a RAID5 array) and a forth small boot HD. I first started to use the onboard RAID capability but that does not work correctly under Linux: the raid capacity is not a real RAID but uses lvm to define some arays. After setting the BIOS back to normal SATA mode and whiping the HDs, the first boot harddisk (/dev/sda) is seen as /dev/sda BEFORE mounting and after mounting as /dev/mapper/nvidia_. CentOS is unable to install on it (and grub is not installable on it either). So somehow the harddisk is still seen as if it belongs to some lvm volume. I tried to clean out the HD by issuing a few dd if=/dev/zero of=/dev/sda commands to wipe the starting cylinders and final cylinders but to no avail. Did anyone see this problem and did anyone find a solution? UPDATE When I create only a single ext3 partition on the first HD (/dev/mapper/nvidia_...) no LVM partitions are seen and I can boot from /dev/mapper/nvidia_.... Now the next step is to see how I can get rid of this folly.

  Read the article

• PBS batch jobs - the qalter command

  - by Ryan Budney

  I've got a giant computation running on a Scientific Linux cluster. At present I have over 600 jobs parked in the queue, waiting for processor time, while a few are running. I'm trying to use the qalter command on some of the idle but scheduled jobs. I'd like to schedule them for a later time, so that other users can jump part of the queue, sort of as an act of politeness. Is this doable? For example, JOBNAME 292399 is currently idle, scheduled to be run whenever a spot in the queue opens up. But if I run qalter -a 10051000 292398 followed by qrerun 292398 I get qrerun: Request invalid for state of job 292398.euler. From the qalter documentation, I thought 10051000 refers to tomorrow (oct 5th, 10am) but perhaps I'm misunderstanding something? If I'm going about this the wrong way, please let me know. The main thing I'm looking for is a command that's easily scriptable, so that I can modify when my queued tasks get run. qalter seems good for those purposes if I can get it working. I'd rather avoid running qdel and re qsubbing the computations, as there's a bookkeeping issue on which tasks to restart (vs which ones not to). I want to avoid that kind of bookkeeping. From googling around I notice some qalter commands have rather different date formats, but the above appears to be correct, as far as I can tell from the man docs. Any help would be appreciated.

  Read the article

• Page reload needed several times before loading normally

  - by tim peterson

  Sorry my question is so vague I just have no idea where to start in solving it and am quite a novice with servers. Recently my site (an https connection, running on an Amazon EC2 ubuntu apache2.2) has this issue where I need to load the page several times (3-4) before it will load normally without issue. It will then load normally as long as I keep loading pages regularly (every couple seconds). It will stall again if I don't load pages for a few minutes. It has nothing to do with my application because I don't have this problem with the exact same app codebase on my Apache installation on my laptop. The only thing to my knowledge that I changed is that I installed mod_pagespeed https://developers.google.com/speed/pagespeed/mod. However, I have since turned it off by setting my pagespeed.conf to mod_pagespeed off. Unfortunately, that didn't solve the problem. I'm wondering general advice on how to troubleshoot this problem. For instance are there linux commands to check page loading peformance? Also, it looks like I have lots of new error.logs in my /var/log/apache2 directory which i believe weren't there a few months ago. lots of this : error.log RewriteLog.log.24.gz ssl_access.log.40.gz error.log.1 RewriteLog.log.25.gz ssl_access.log.41.gz error.log.10.gz RewriteLog.log.26.gz ssl_access.log.42.gz error.log.11.gz RewriteLog.log.27.gz any thoughts? thank you, tim

  Read the article

• stunnel not working - stunnel.pem: No such file or directory

  - by Marronsuisse

  I am trying to install stunnel on an amazon LINUX machine. (i want to configure postfix so that it sends its emails through amazon ses) I first tried to install from the tar.gz package download from http://www.stunnel.org and installed with the commands: ./configure make make install but than the stunnel command was still not found. Then I installed with yum install stunnel. But now when I try I get: sudo stunnel 2012.06.23 06:51:53 LOG7[20071:3078289200]: Snagged 64 random bytes from /root/.rnd 2012.06.23 06:51:53 LOG7[20071:3078289200]: Wrote 1024 new random bytes to /root/.rnd 2012.06.23 06:51:53 LOG7[20071:3078289200]: RAND_status claims sufficient entropy for the PRNG 2012.06.23 06:51:53 LOG7[20071:3078289200]: PRNG seeded successfully 2012.06.23 06:51:53 LOG3[20071:3078289200]: stunnel.pem: No such file or directory (2) So it seems there is still a problem with the install. When I use the locate stunnel command, I see files a bit everywhere. How can I do to have a clean install of stunnel? Edit: i was following this procedure: http://docs.amazonwebservices.com/ses/latest/DeveloperGuide/SMTP.MTAs.SecureTunnel.html when I got stuck at point 5 and got the stunnel.pem: No such file or directory message.

  Read the article

• Drop database on DB2 9.5 - SQL1035N The database is currently in use

  - by Tommy

  I've never got this working the first time, but now I can't seem to do i at all. There is a connection pool somewhere using the database, so trying to drop the database when an application is using the database should give this error. The problem is there are no connection to the database when I issue these commands: db2 connect to mydatabase db2 quiesce database immediate force connections db2 connect reset db2 drop database mydatabase This allways give: SQL1035N The database is currently in use. SQLSTATE=57019 running this command shows no connections/applications DB2 list applications I can even deactivate the database, but still can't drop it. db2 => deactivate database mydatabase DB20000I The DEACTIVATE DATABASE command completed successfully. db2 => drop database mydatabase SQL1035N The database is currently in use. SQLSTATE=57019 db2 => Anyone got any clues? I'm running the cmd-windows as the local administrator (windows 2008) and this is also the admin for DB2. The connectionpool-user cannot connect during quiesce-state.

  Read the article

• Monitor Exchange Email Address and run scripts

  - by WernerCD

  Okay... Not sure how "out there" this thought is... Right now to send a pager message (aka text message), a user logs into our AS400... logs into the program... enters user name and message and hit's F10 to send. With a little looking, it seems that you can run remote commands to the AS400 via FTP. So I'm working on building a script (batch or otherwise) that, given two parameters (user, message), will FTP into the AS400 and run a remote command: c:\>ftp server user: admin password: ***** ftp> quote rcmd SNDPGRMSG TOPGR(JDOE) MSG('This is a Test') ftp> quit So... what I want to do is setup an email account on our Exchange server Monitor the account for incoming mail upon receipt of incoming mail, parse it... say for example subject is defined as "Recipient" and email text is defined as "Pager message" run a batch that uses the above mentioned TOPGR and MSG as parameters... via FTP to the AS400 mark email as "read" The main thing I'm not sure about is monitoring an exchange account and running a script on incoming emails. I'm sure what I want to do is possible... but where would I start? EDIT: Clarification The main reasons for using this four part system are logging (messages sent via this are logged and reported by the AS400 program) and the existing scheduler for redirecting pages (For example, the weekly on-call person = TOPGR(oncall) gets updated by the AS400 program). I'm also trying to remove duplicate work. If I can get this setup working, I can redirect pages from OTHER systems into this one. I then don't have to update 2, soon to be 3, systems with current phone numbers, carriers, on-call schedules, etc. System #2 and #3 can just "email" [email protected].

  Read the article

• Virtualbox HTTP load testing, host CPU overload issues

  - by aschuler

  I'm doing HTTP load testing benchmarks (using Apache Benchmark and Siege) on a small Java EE 1.7.0 / Tomcat 7.0.26 application running on a Debian Squeeze 6.0.4 x64 virtualized with Virtualbox 4.1.8. The computer host is Ubuntu 11.10 x64. I've modified those parameters in the Tomcat server.xml : <Connector port="8080" protocol="HTTP/1.1" connectionTimeout="200000" redirectPort="8443" acceptCount="2000" maxThreads="150" minSpareThreads="50" /> The application executed on the server takes around 300ms. This app is running well until a certain amount of concurrent connections like those one : ab -n 500 -c 150 http://xx.xx.xx.xx:8080/myapp/ ab -n 1000 -c 50 http://xx.xx.xx.xx:8080/myapp/ siege -b -c 100 -r 20 http://xx.xx.xx.xx:8080/myapp/ A lot of socket connection timed out happens and this completly overload the host processor (but the CPU load inside the VM is normal). Doing an htop on the host, i can see that the Virtualbox processus is running under 300% CPU and never come down even after the load test is finished. (I've allocated 4 processors to the VM, if I allocate only one processor, CPU load goes under 100%). Restarting Tomcat don't do anything, i'm forced to restart the whole VM. I've tryed to launch those ab/siege commands locally on the VM and everything goes well. I first thought it was related to a linux network limit as explained here: Running some benchmarks using ab, and tomcat starts to really slow down So I've modified those TCP parameters : echo 15 > /proc/sys/net/ipv4/tcp_fin_timeout echo 30 > /proc/sys/net/ipv4/tcp_keepalive_intvl echo 1 > /proc/sys/net/ipv4/tcp_tw_recycle echo 1 > /proc/sys/net/ipv4/tcp_tw_reuse It seems to be better, but it continues to overload the host CPU and output socket connections time out at a certain amount of concurrent connections. I'm wondering if this is not related to how Virtualbox handles external concurrent connections.

  Read the article

• saslauthd authentication error

  - by James

  My server has developed an expected problem where I am unable to connect from a mail client. I've looked at the server logs and the only thing that looks to identify a problem are events like the following: Nov 23 18:32:43 hig3 dovecot: imap-login: Login: user=, method=PLAIN, rip=xxxxxxxx, lip=xxxxxxx, TLS Nov 23 18:32:55 hig3 postfix/smtpd[11653]: connect from xxxxxxx.co.uk[xxxxxxx] Nov 23 18:32:55 hig3 postfix/smtpd[11653]: warning: SASL authentication failure: cannot connect to saslauthd server: No such file or directory Nov 23 18:32:55 hig3 postfix/smtpd[11653]: warning: xxxxxxx.co.uk[xxxxxxxx]: SASL LOGIN authentication failed: generic failure Nov 23 18:32:56 hig3 postfix/smtpd[11653]: lost connection after AUTH from xxxxxxx.co.uk[xxxxxxx] Nov 23 18:32:56 hig3 postfix/smtpd[11653]: disconnect from xxxxxxx.co.uk[xxxxxxx] The problem is unusual, because just half an hour previously at my office, I was not being prompted for a correct username and password in my mail client. I haven't made any changes to the server, so I can't understand what would have happened to make this error occur. Searches for the error messages yield various results, with 'fixes' that I'm uncertain of (obviously don't want to make it worse or fix something that isn't broken). When I run testsaslauthd -u xxxxx -p xxxxxx I also get the following result: connect() : No such file or directory But when I run testsaslauthd -u xxxxx -p xxxxxx -f /var/spool/postfix/var/run/saslauthd/mux -s smtp I get: 0: OK "Success." I found those commands on another forum and am not entirely sure what they mean, but I'm hoping they might give an indication of where the problem might lie. If it makes any difference, I'm running Ubuntu 10.04.1, Postfix 2.7.0 and Webmin/ Virtualmin.

  Read the article

• Selenium server causes crazy load on server - how to prevent?

  - by Eric

  I'm running this linux: Linux host.themepark.com 2.6.32-220.4.1.el6.x86_64 #1 SMP Tue Jan 24 02:13:44 GMT 2012 x86_64 x86_64 x86_64 GNU/Linux And I run the Selenium stand-alone server on my box with this command: java -jar /home/l/cron/selenium-server-standalone-2.24.1.jar > /logs/selenium.log 2>&1 & Here's the problem: as soon as I do that, the server load starts skyrocketing. I even went back and downloaded older versions of the Selenium server, but same results with 2.23.1, 2.23.0, and 2.19.0. Note that the server load starts going nuts before I issue ANY commands to Selenium or do anything else. All I'm doing is firing up the server, per the command above. This used to work perfectly on my server without causing massive server load, so something has changed, but I'm not sure what. My server is a managed VPS so I don't know if there is some kind of auto-update script that kicked in or what... but it's a problem. (Incidentally, even though the server load climbs like crazy, everything still works: after firing up Selenium, my server creates a screen with Xvfb so Firefox will be happy, then a PHP script talks to Selenium to do what it needs to do before shutting everything down. It takes a LONG time, and the load gets all the way up to 8 [!!!] before it is finished, which kills my web server and makes the main site horribly unresponsive... but it does get everything done.) Any suggestions for what is going on, why it's started doing this and/or, most importantly, how I can make Selenium not kill the server when it starts up... would be GREATLY appreciated!

  Read the article

• PXE booting LACP hosts on Force10 S50N with FTOS

  - by lolwutreddit

  Hardware: S50N Firmware: FTOS 8.4.2.6 Problem: We're trying to PXE boot some servers that are connected via port-channel interfaces with LACP. Current Work-around: we PXE boot a server with a single interface (eth0), and then use a Perl script to turn up the port-channel interfaces after the server is built. Details: Is anyone doing anything similar on Force10 S50 switches with FTOS? If not, is anyone doing this on another S series, or larger chassis-based Force10? I'm wondering if Native VLAN will solve this, since ports in a port-channel cannot explicitly have a VLAN set, and they don't seem to use the tagged or untagged VLAN that the port channel is in. I will confirm this next (I think it's the only thing I haven't tried) Juniper Example: http://broken.net/openindiana/how-to-pxe-boot-systems-on-lacp-using-juniper-switches/ Cisco: there are plenty of documented ways to solve this issue on IOS and Nexus Update/Edit: since there seems to be no way to use interface or port-channel mode commands to get the individual interfaces to show up in spanning-tree (rtsp in this case), the ports should never go into a forwarding state. I'm not going to mess with it anymore unless a) someone that has experience passes it on, or b) Force10 comes up with a solution for this (I'm guessing it will only be introduced on other S platforms (S55, S60), since the S50 seems to be near EOL). I'm basing that on the fact that the Open Automation type features are only being supported on the newer switches.

  Read the article

• BSOD trying to migrate Windows XP from a physical to a virtual machine

  - by pauldoo

  I am attempting to migrate a Windows XP Home installation from a physical machine to a virtual machine. The physical machine has two hard disks; the first is 250GB containing the "C:", the second is 1TB containing "D:". I'd like to create a new virtual machine stored on the D:, which is a copy of the Windows XP Home installation that is currently on the C:. (This will leave the 250GB drive clear for me to install a fresh copy of Windows 7, and still be able to access the old XP installation if necessary.) The first method I tried was to follow the instructions here: http://www.virtualbox.org/wiki/Migrate_Windows I booted up from an Ubuntu Live CD in order to execute the Linux commands whilst the Windows system wasn't running. With this method the virtual machine would always blue screen on startup with a "STOP 0x0000007B" message. The instructions above say to try a "repair install" using the Windows XP disc. Unfortunately for me my XP disc is scratched and will not boot so I was unable to try a repair install. The second method I tried was to use "VMWare Converter Standalone Client". This tool executed without any errors, but again produced a virtual machine that blue screens on startup with the same "STOP" message. Are there any other methods to move the Windows XP installation into a virtual machine? I think next I will try some more manual process to create the cloned virtual machine. I think I will try installing a fresh copy of Windows XP to a virtual machine, then once that is booting OK I will ntfsclone the source C: partition over the top. Perhaps this will fix the booting problems if the issue is related to the MBR or partition table in some way.

  Read the article

• Do I have to do anything for file ACLs to work both before and after I reformat a computer?

  - by Zian Choy

  Let's say that I have a computer running Windows Vista with 2 users: Alice and Bob. Alice is the admin and Bob is a normal user. They each have files in their respective My Documents folders and Bob is not allowed to view Alice's files and Alice has to jump through a UAC elevation to view Bob's. If Alice copies all the files on the computer to an external NTFS-formatted hard drive with the following 2 commands: robocopy "E:\Bob's Files" "C:\Users\Bob\My Documents" /MIR robocopy "E:\Alice's Files" "C:\Users\Alice\My Documents" /MIR And then reformats the hard drive, installs a fresh copy of Windows, and creates 2 users named Alice and Bob on the computer, then will everything in the first paragraph be true after Alice copies the files back onto the internal hard drive? Assume that when the files are copied back over, she logs in as Bob and then copies Bob's files and likewise with her own files. Possibly relevant: Alice and Bob also have passwords on their user accounts and they create new passwords after the computer is reformatted. The main post has been tweaked slightly to make the question clearer. Answers that predate April 2011 are referring to an earlier version of this post.

  Read the article

• Xbox360 Universal Media Remote - out of sync?

  - by Traveling Tech Guy

  Hi, I have the Universal Media Remote from Microsoft, which was included with my HD-DVD package. I've been using it for over a year to watch videos/DVDs on my Xbox360 and it saved me the hassle of navigating with the game controller (which turns itself off every 5 minutes).All of a sudden (it didn't fall or suffer any severe trauma), it does not communicate with the Xbox anymore: it is on, I replaced batteries several times, but the Xbox does not respond to commands. The TV does - volume, channels, etc. - but I need the Xbox functionality.As far as I can see, there's no way to sync the remote with the Xbox - it lacks that small sync button that the game controllers have.I called Microsoft Support and spoke for an hour to someone who, I guess didn't know what to do at all. Bottom line - since it's been over a year, they won't fix/replace it - I have to get a new one.Before I do (if I do), I need to know if there's anything I can do with the existing remote, and will I have the same problem with a new one (i.e. the problem is with the Xbox itself)? Thanks!

  Read the article

< Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >