Search Results

Search found 14861 results on 595 pages for 'high speed computing'.

Page 156/595 | < Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >

  • VPN service for 4in6

    - by Deshene
    I have a local network with internet access. But unfortunately IPv4 internet connection speed is limited to 1mbps, which is realy sad. Fortunately I have a native IPv6, and there is no connection speed limit over IPv6. So, in order to get a good internet connection I made a plan: connect to the VPN-service over IPv6, and pass all IPv4 traffic through IPv6 tunnel, or something like that, I think you get the idea. I suggested to use service like HideMyAss.com, but unfortunately they don't support IPv6. The question is: Is there any existing VPN service that will make my dreams come true, and is easy to use, which I could connect over PPTP or OpenVPN (I want to set up connection to VPN in my router settings).

    Read the article

  • Slow write speeds on new Gigabit home file server

    - by Ryan Holder
    So I finally got all my parts delivered to setup a home file/backup server this week. It's currently running Ubuntu Server and I'm using Samba to share files on my network. The server currently has a 2TB WD Green drive in it connected to a Asus M5A78L-M This is then connected via CAT6a to my new Gigabit switch (TP-Link TL-SG1005D). My home desktop is then also connected to this switch and again also through CAT6a cable. Currently when transfering files I will get a perfect 100MB/s read from the server to my Windows machine. When copying from my Windows machine to the server I get around 30/38MB/s. I know this drive is capable is faster speeds so would anybody have an idea of where the bottleneck is? Any help would be greatly appreciated :) EDIT: I have found ftp's write speed is much closer to what my Samba read speed is so I'm going to give it a guess that is a software problem rather than hardware

    Read the article

  • CPU clock scales down so computer is unusable after switching to battery

    - by Ryan
    When I am plugged in my laptop runs great however when I unplug it and I'm on battery power my CPU clock speed scales down pretty much all the way. I know this is happening by monitoring the clock speed. When plugged in it will usually stay between 1000MHz and 3000MHz but when I unplug it it quickly scales down to less than 500MHz and will get as low as 100MHz and it will NEVER scale up at all on battery power. After I plug the power back in it will then begin operating normally in about a minute. I have tried setting the MIN and MAX CPU performance in power options to 100% and have tried messing around with cooling settings which seemed to be a problem with HP laptops. I have a Toshiba Satellite M500-ST6444 running Windows 7. The BIOS is up to date. I have tried two versions.

    Read the article

  • Does adding 1066Mhz DDR3 SODIMM to a 1600Mhz FSB laptop make sense?

    - by Alain Pannetier
    My previous laptop had 4x4GB 1066 Mhz DDR3. My new laptop instead has only 2x4GB 1600 Mhz DDR3. Using dmidecode I gather my FSB is set to 2300Mhz. Max Speed: 3800 MHz Current Speed: 2300 MHz 2 questions: Can somebody confirm I can safely add two "old" 1066Mhz modules to my new laptop before I treat myself to faster DDR3 modules? I understand this should not slow down the faster 2 1600 Mhz DDR3 modules. Correct? If this is of any relevance, I'm running Linux Mint Maya.

    Read the article

  • Keeping DB Table sorted using multi-field formula (Microsoft SQL Server)

    - by user298167
    I have a JOB table, with two interesting columns: Creation Date Importance (high - 3, medium 2, low - 1). A JOB record's priority calculated like this: Priority = Importance * (time passed since creation) The problem is, every time I would like to pick 200 jobs with highest priority, and I don't want to resort the table. Is there a way to keep rows sorted? I was also thinking about having three tables one for High, Medium and Low and then sort those by Creation Date.

    Read the article

  • Late Model 2011 Macbook Pro with SSD appears to be off somehow

    - by chris
    Ok, I just got a SSD for my Macbook Pro Late-2011. The specs from what I read are that the laptop is capable of 6gbps, so I got myself a OZC Agility 240gb 6gbps SSD. Decided to join the club and speed test it with Blackmagic Disk Speed Test.. and the results are equivilent to that of a 3gbps setup. So.. I am wondering overall is there a configuration setting somewhere I can tweak? The original HD was a 500gb HDD the spinning kind. So I'm figuring maybe thats why there may be a setting somewhere hidden I dunno about that I can tweak, just wanna see if anyone else knows if this is the case. edit should also mention did a fresh factory install, nothing carried over from original hd

    Read the article

  • How can I add a previous button to this Jquery Content Slider?

    - by user1269988
    I did this nice tutorial for a Jquery Content Slider: http://brenelz.com/blog/build-a-content-slider-with-jquery/ Here is my test page: http://www.gregquinn.com/oneworld/brenez_slider_test.html But the Left button is hidden on the first slide and I do not want it to be. I don't know much about jquery but I tried to set the left button from opacity o to 100 or 1 and it didn't work the button showed up once but did not work. Does anyone know how to do this? Here is the code: (function($) { $.fn.ContentSlider = function(options) { var defaults = { leftBtn : 'images/panel_previous_btn.gif', rightBtn : 'images/panel_next_btn.gif', width : '900px', height : '400px', speed : 400, easing : 'easeOutQuad', textResize : false, IE_h2 : '26px', IE_p : '11px' } var defaultWidth = defaults.width; var o = $.extend(defaults, options); var w = parseInt(o.width); var n = this.children('.cs_wrapper').children('.cs_slider').children('.cs_article').length; var x = -1*w*n+w; // Minimum left value var p = parseInt(o.width)/parseInt(defaultWidth); var thisInstance = this.attr('id'); var inuse = false; // Prevents colliding animations function moveSlider(d, b) { var l = parseInt(b.siblings('.cs_wrapper').children('.cs_slider').css('left')); if(isNaN(l)) { var l = 0; } var m = (d=='left') ? l-w : l+w; if(m<=0&&m>=x) { b .siblings('.cs_wrapper') .children('.cs_slider') .animate({ 'left':m+'px' }, o.speed, o.easing, function() { inuse=false; }); if(b.attr('class')=='cs_leftBtn') { var thisBtn = $('#'+thisInstance+' .cs_leftBtn'); var otherBtn = $('#'+thisInstance+' .cs_rightBtn'); } else { var thisBtn = $('#'+thisInstance+' .cs_rightBtn'); var otherBtn = $('#'+thisInstance+' .cs_leftBtn'); } if(m==0||m==x) { thisBtn.animate({ 'opacity':'0' }, o.speed, o.easing, function() { thisBtn.hide(); }); } if(otherBtn.css('opacity')=='0') { otherBtn.show().animate({ 'opacity':'1' }, { duration:o.speed, easing:o.easing }); } } } function vCenterBtns(b) { // Safari and IE don't seem to like the CSS used to vertically center // the buttons, so we'll force it with this function var mid = parseInt(o.height)/2; b .find('.cs_leftBtn img').css({ 'top':mid+'px', 'padding':0 }).end() .find('.cs_rightBtn img').css({ 'top':mid+'px', 'padding':0 }); } return this.each(function() { $(this) // Set the width and height of the div to the defined size .css({ width:o.width, height:o.height }) // Add the buttons to move left and right .prepend('<a href="#" class="cs_leftBtn"><img src="'+o.leftBtn+'" /></a>') .append('<a href="#" class="cs_rightBtn"><img src="'+o.rightBtn+'" /></a>') // Dig down to the article div elements .find('.cs_article') // Set the width and height of the div to the defined size .css({ width:o.width, height:o.height }) .end() // Animate the entrance of the buttons .find('.cs_leftBtn') .css('opacity','0') .hide() .end() .find('.cs_rightBtn') .hide() .animate({ 'width':'show' }); // Resize the font to match the bounding box if(o.textResize===true) { var h2FontSize = $(this).find('h2').css('font-size'); var pFontSize = $(this).find('p').css('font-size'); $.each(jQuery.browser, function(i) { if($.browser.msie) { h2FontSize = o.IE_h2; pFontSize = o.IE_p; } }); $(this).find('h2').css({ 'font-size' : parseFloat(h2FontSize)*p+'px', 'margin-left' : '66%' }); $(this).find('p').css({ 'font-size' : parseFloat(pFontSize)*p+'px', 'margin-left' : '66%' }); $(this).find('.readmore').css({ 'font-size' : parseFloat(pFontSize)*p+'px', 'margin-left' : '66%' }); } // Store a copy of the button in a variable to pass to moveSlider() var leftBtn = $(this).children('.cs_leftBtn'); leftBtn.bind('click', function() { if(inuse===false) { inuse = true; moveSlider('right', leftBtn); } return false; // Keep the link from firing }); // Store a copy of the button in a variable to pass to moveSlider() var rightBtn = $(this).children('.cs_rightBtn'); rightBtn.bind('click', function() { if(inuse===false) { inuse=true; moveSlider('left', rightBtn); } return false; // Keep the link from firing }); }); } })(jQuery)

    Read the article

  • afp/smb transfers caps at 2 megabytes/sec, wireless N

    - by RD.
    I wanted to transfer files between two mac computers. The network is wireless-N and both computers have wireless-N modules in them. The problem is that when I transfer files between them, via file sharing (afp) the network speed caps at 2 megabytes/sec. Just downloading files from the internet I can get faster speeds, so this isn't a constriction of my wifi bandwidth, it appears to be a constriction of the protocol being used. My wifi-n is set to 130mbits, so I should see real world transfer speeds around 12-16 megabytes/sec I did this command on both computers sudo sysctl -w net.inet.tcp.delayed_ack=0 which is supposed to lower tcp overhead, but this did not affect it. How can I get the speed I am expecting?

    Read the article

  • What is fastest way to backup a disk image over LAN?

    - by David Balažic
    Sometimes I boot sysrescd or a similar live linux on a PC to backup the hardrive over local network to my server. I noticed many times, that the transfer speed is not optimal (slower than HDD and network speed). Any rules of thumb what to do and what to avoid? What I typically do is something like: dd bs=16M if=/dev/sda | nc ... # on client nc ... | dd bs=16M of=/destination/disk/backup1 # on server I also "throw" in lzop (other are way too slow) and sometimes on the fly md5sum calculation (both of uncompressed and compress source). I try to add (m)buffer (or other alternatives) to improve throughput (and get a progress indicator). I noticed that even with enough free CPU, adding commands to the pipeline slows things down. Typically the destination is on a NTFS volume (accessed via ntfs-3g, with the _big_writes_ option).

    Read the article

  • How can i implement the NULL Object Design Pattern in a generic form?

    - by Colour Blend
    Is there a way to implement the null object design pattern in a generic form so that i don't need to implement it for every buisness object. For me, there are two high level classes you'll need for every business class. One for a single record and another for a list. So i think there should be a way to implement the NULL Object design pattern at a high level and not have to implement it for every class. Is there a way and how please?

    Read the article

  • Web & SQL Hosting 32 vs. 16 GB of ram

    - by TravisK
    I'm in the market for a new dedicated host for my website. My question is I can pay more to upgrade to 32GB of RAM, but it seems overkill for my website right now, in fact, 16GB seems a little overkill. However, I run a lot of pretty intense full text searches for my site. I'm wondering if SQL Server would benefit, or could it be configured to use the 32 GB of RAM if I purchase the additional to help speed things up? I am assuming that most of my latency is caused by disk I/O and that for the extra money spent on RAM, I might not see any improvement in overall speed?

    Read the article

  • Algorithm to suggest a list of tags to users

    - by Itay Moav
    Given a free text, I need to analyse this this text and suggest a list of tags from a pre existing list. What algorithms are out there in the market? Can they handle a case where, for example, the text have a word like high cholesterol and I would like it so suggest heart disease although "high cholesterol" might not exists (initially) in the pre defined list.

    Read the article

  • linux: upload / download difference on network shares

    - by Batsu
    I have a Red Hat Enterprise Linux 6 (with SELinux) which shows significant differences of speed between download and upload (the latter significantly slower) of files shared over the LAN. The bottleneck seems to be the output of the linux machine since I have a rate around 1Mb/s when WinXP machines download files shared (using samba) by the RHEL machine uploading files from the RHEL to a WinXP's shared folder while uploading from the XP machines to linux's shares downloading XPs' shares on the RHEL any share between Windows machines only run smooth (around 50Mb/s). Since the upload from RHEL to WinXP's share is slowed too I would exclude an issue in the configuration of samba. What could possibly determine this limit in the upload speed? update: iptables doesn't show any output rule and disabling it doesn't show any noticeable difference, so I would rule out it too.

    Read the article

  • Weird nfs performance: 1 thread better than 8, 8 better than 2!

    - by Joe
    I'm trying to determine the cause of poor nfs performance between two Xen Virtual Machines (client & server) running on the same host. Specifically, the speed at which I can sequentially read a 1GB file on the client is much lower than what would be expected based on the measured network connection speed between the two VMs and the measured speed of reading the file directly on the server. The VMs are running Ubuntu 9.04 and the server is using the nfs-kernel-server package. According to various NFS tuning resources, changing the number of nfsd threads (in my case kernel threads) can affect performance. Usually this advice is framed in terms of increasing the number from the default of 8 on heavily-used servers. What I find in my current configuration: RPCNFSDCOUNT=8: (default): 13.5-30 seconds to cat a 1GB file on the client so 35-80MB/sec RPCNFSDCOUNT=16: 18s to cat the file 60MB/s RPCNFSDCOUNT=1: 8-9 seconds to cat the file (!!?!) 125MB/s RPCNFSDCOUNT=2: 87s to cat the file 12MB/s I should mention that the file I'm exporting is on a RevoDrive SSD mounted on the server using Xen's PCI-passthrough; on the server I can cat the file in under seconds ( 250MB/s). I am dropping caches on the client before each test. I don't really want to leave the server configured with just one thread as I'm guessing that won't work so well when there are multiple clients, but I might be misunderstanding how that works. I have repeated the tests a few times (changing the server config in between) and the results are fairly consistent. So my question is: why is the best performance with 1 thread? A few other things I have tried changing, to little or no effect: increasing the values of /proc/sys/net/ipv4/ipfrag_low_thresh and /proc/sys/net/ipv4/ipfrag_high_thresh to 512K, 1M from the default 192K,256K increasing the value of /proc/sys/net/core/rmem_default and /proc/sys/net/core/rmem_max to 1M from the default of 128K mounting with client options rsize=32768, wsize=32768 From the output of sar -d I understand that the actual read sizes going to the underlying device are rather small (<100 bytes) but this doesn't cause a problem when reading the file locally on the client. The RevoDrive actually exposes two "SATA" devices /dev/sda and /dev/sdb, then dmraid picks up a fakeRAID-0 striped across them which I have mounted to /mnt/ssd and then bind-mounted to /export/ssd. I've done local tests on my file using both locations and see the good performance mentioned above. If answers/comments ask for more details I will add them.

    Read the article

  • Which SSL certificate to buy [closed]

    - by Sparsh Gupta
    I am reading several notes on SSL certificates and comparison. What matters to me the most is speed. I can read that encryption is same with all different certificates available but I was wondering if there is any difference in the performance of the website with different certificates involved. I am ofcourse interested in end to end response times and I wonder if the type of encryption or number of certificates required as Chain Certificates makes a difference in speed. I dont really care for cost but looking for a good SSL certificate which ideally gives me absolutely no pain and best performance. Recommendations?

    Read the article

  • slow software raid

    - by Jure1873
    I've got software raid 1 for / and /home and it seems I'm not getting the right speed out of it. Reading from md0 I get around 100 MB/sec Reading from sda or sdb I get around 95-105 MB/sec I thought I would get more speed (while reading data) from two drives. I don't know what is the problem. I'm using kernel 2.6.31-18 hdparm -tT /dev/md0 /dev/md0: Timing cached reads: 2078 MB in 2.00 seconds = 1039.72 MB/sec Timing buffered disk reads: 304 MB in 3.01 seconds = 100.96 MB/sec hdparm -tT /dev/sda /dev/sda: Timing cached reads: 2084 MB in 2.00 seconds = 1041.93 MB/sec Timing buffered disk reads: 316 MB in 3.02 seconds = 104.77 MB/sec hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 2150 MB in 2.00 seconds = 1075.94 MB/sec Timing buffered disk reads: 302 MB in 3.01 seconds = 100.47 MB/sec Edit: Raid 1

    Read the article

  • SSD Performance for PHP?

    - by Andrew Fashion
    My programmer just built an application with PHP using Doctrine ORM (will be a high traffic social networking website), and it's very heavy in PHP/Apache and CPU. The queries are wonderfully fast, and MySQL is barely using any CPU, it's just Apache. I was curious to if an SSD would help speed up PHP/Apache, because I know the bottleneck is in PHP reading multiple files, class files, and loading up a bunch of data. So common sense makes me think if PHP is reading multiple PHP files, an SSD would only help as far as read/write? I was thinking of doing a high performance SSD for the PHP application, but for user image uploads, I would just continue using a 15k SAS. Is there any performance issues regarding using an SSD in this kind of situation? And would it prove to help speed up PHP/Apache, and help the CPU problem out?

    Read the article

  • My VPS ubuntu server is very slow

    - by askmike
    I just installed a frech copy of Ubuntu 12.04 on my vps because my old installation was very slow, unfortunately this did not fix the problem. With slow I mean requests for my PHP websites take a long time, very slow (30 sec per request) to slow (3+ sec per request). When it's really bad SSH is also laggish. The websites are: askmike.org (pretty standard Wordpress) mvr.me (own PHP) slow? very slow: Here is a picture of loading a clean install of wordpress slow: here is a picture of loading a small PHP based website the vps The VPS has 256mb ram and an 25GB hdd. Besides serving the 2 small websites it isn't doing anything AFAIK. What have I installed Clean Ubuntu server 12.04 LAMP stack few things like git and nodejs (not using both) ossec (because I thought my server was getting hammered) munin What I already tried / done I installed munin so that I could watch io speed and such. The problem is that I don't know where to look for in the munin report. I checked logs and don't see anything strange (although I don't really know where to look for besides strange / repetitive errors and GET requests). I configured Apache MPM to: <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 40 MaxRequestsPerChild 0 </IfModule> (apache is using prefork, the default) Stats I copied the munin report as it appeared at 4:50 last night to a site hosted on a shared webhost. Note that tonight my mysql crashed somewhere after 1:00 (which is a new problem altogether), so therefor the graph for last night might look strange. Can anyone help me get my VPS up to normal speed? EDIT: Thanks for the replies. The VPS is 10 bucks a month and is from directvps.nl (Dutch host and I'm also dutch). I did two speed tests for disk IO: $ dd if=/dev/zero of=test bs=64k count=16k conv=fdatasync 1073741824 bytes (1.1 GB) copied, 23.1506 s, 46.4 MB/s $ dd if=/dev/zero of=test bs=64k count=16k conv=fdatasync 1073741824 bytes (1.1 GB) copied, 39.3796 s, 27.3 MB/s Anyway: how can I prove to my VPS host that it is to slow? I can understand a server being busy slowing a website down. But 5-30 sec loadtime for a normal PHP webpage?

    Read the article

  • Using TrueCrypt (software encryption) with an SSD

    - by Shackrock
    I use full drive encryption (FDE) w/ TrueCrypt on my laptop. I have a 2nd gen I7 with AES instruction support, so honestly I can't even notice a speed change on the system with it on. My question, is for those who know about SSD's a lot. I previously (early 2011) read articles about how software encryption will negate the speed benefits that an SSD provides - because of the need for the SSD to send a delete command, then a write command, for every encrypted write - instead of just writing over data like a regular HDD would (or something like this...honestly I can't remember...ha!). Anyway, any improvements in this field? Is it pointless for me to grab an SSD if I'm using FDE? Thanks all.

    Read the article

  • How can I restrict my mates to stop downloading?

    - by user239295
    We are sharing an internet broadband connection with 6 users at a place we live. We get 20 gb fup ( Fair usage policy) with 2 mbps speed from the ISP after the 20 gb is consumed the speed comes down to 512 kbps very difficult to browse any page. The problem is we cannot track which user/mate is downloading and ending the FUP. it is very difficult to track so is there something that we can allot per user some amount of space like 2 gb of downloading or restrict all from downloading so that we can utilize all the fup till the end of the month. We are using this connection as wifi configured. A adsl router is configured as wifi and we all using all 6 laptops. No PC. Any help would be appreciated. I apologize if i am not clear with my question.

    Read the article

  • ADSL improvement in recent years

    - by cleong
    Currently I have a 2mb/s ADSL connection. I signed up for the service more than five years ago. Has technology improved much during that time to allow for greater speed using the same wires? The building I live in is quite old and the lines aren't very good. They weren't able to support 6mb/s service back then. Now I notice that the lowest speed offered by my telco is 10mb/s. Even that would be a serious improvement over what I have now. Here are the stats from the modem: Line Attenuation (Up/Down) [dB]: 10,5 / 15,5 SN Margin (Up/Down) [dB]: 31,5 / 29,0

    Read the article

  • It takes a long time until windows xp recognize I connected USB diks

    - by Pavol G
    Hello IT guys, I have a problem with my new USB disk. When I connect it to my laptop with Windows XP SP2 it takes about 4-5min until Windows recognized it and show it as a new disk. I can also see (disk's LED is blinking) that something is scaning the disk when I connect it, when this is done Windows imediately recognize it. Also when I'm copying data to this disk the speed is about 3.5MB/sec. It's connected using USB2.0. I tried to check for spyware (using spybot), also run windows in safe mode. But still have the same problems. Do you have any idea what could help to solve this problem? On Windows Vista (another laptop) everything is ok, disk loads in about 15sec and speed is about 20-30MB/sec. Thanks a lot for every advice!

    Read the article

  • IPv6 feature in Network Adaptor is Slowing Internet

    - by Teknophilia
    The past few days, my internet browsing has become very poor. It's not a matter of speed, as a speed test will give at least 15Mbps. It seems as if my laptop has a hard time actually connecting to the sites. I've found a possible culprit, but don't know why it would affect anything: Going to adapter settings and disabling ipv6, but leaving ipv4, my browsing is back to normal. Re-enabling ipv6 brings back the issue. This is strange though, because I have always had ipv6 enabled. Moreover, using sites to test ipv6 compatibility, I fail with ipv6 enabled on my adapter, and pass when it's disabled. Ideas about why this is happening, and how to fix it?

    Read the article

< Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >