Search Results

Search found 11930 results on 478 pages for 'shared machines'.

Page 156/478 | < Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >

• Forward all traffic from one IP to another Ip on OS X

  - by Josh

  This is related to this question I just asked... I have two IP address on my iMac I want to "bridge". I'm not sure what the proper terminology is... here's the situation. My iMac has a firewire connection to my laptop and an ethernet connection to the rest of my office. My laptop has an ip of 192.168.100.2 (on the firewire interface). My iMac has an IP of 192.168.100.1 on the firewire interface, and two IPs, 10.1.0.6 and 10.1.0.7, on it's ethernet interface. If I wanted to forward all traffic coming in from 192.168.100.2 on my OS X machine to go out on IP 10.1.0.7, and vice-versa, can this be done? I assume I would use the ipfw command. Essentially I want to "bridge" the firewire network to the ethernet network so my laptop can see all the machines on the 10.1 network, and all those machines can see my laptop at 10.1.0.7. Is this possible?

  Read the article

• System Center 2012 VMM UI is very slow

  - by Grant

  I've recently setup system center 2012 a new server 2008 r2 server which I'm using for virtual machines. Everything seems to be working fine, and the virtual machines are nice and fast. But the Virtual Machine Manager interface is always excruciatingly slow. Sometimes taking up to 15 seconds moving between screens. It's very frustrating trying to use it when a task that just involves a couple clicks ends up taking several minutes. Pages that have a lot of form fields seem to take the longest to load - such as the page to change hardware settings of a virtual machine. Is this just normal performance for VMM? If not, where can I look to find what is slowing it down. Nothing else on the system seems to suffer. I can load and use Hyper-V manager with no noticable slowness. Even programs like event viewer that are usually rather slow seem to load fairly fast. Only the system center programs seem slow. Server is a Dell R710, 2x16 core opteron 6274 processors, 96GB RAM. OS drive is 2x500GB 7.2k RPM SAS drives in RAID1 (opted for the less expensive 7.2k drives since pretty much everything is stored on the SAN). Am I just being impatient? Does anyone else use VMM 2012 and find it slow?

  Read the article

• Why can't I debug my ASP project through a remote desktop connection?

  - by Anthony Benavente

  I just asked this question in Stack Overflow but I figured this stack exchange forum is a better fit. It's been about a month of trying to figure out this problem and we've still not found a solution. We have about seven virtual machines on a server running Windows XP Professional w/ SP 3 all with Visual Studio Interdev and IIS 5.1 installed. Running the programs all work fine, but we just can't debug through remote desktop. When we are logged into the server console (through VM Sphere) and log into one of the virtual machines through there, we are able to debug properly. We figured the issue lies with some kind of permissions for Remote Desktop Users. We've tried nearly every article on the internet (exaggerating of course) and are about to give up hope. One more thing, when we are logged into the virtual machine through the server console and then remote in, the user that was logged into the console is kicked off but debugging works! Does remoting in trick the computer into giving us the correct permissions? I'm really not sure how it works. I know that this technology predates human history, but we are in the process of migrating from ASP Classic to ASP.NET Specs: - Windows XP Professional W/ SP3 - IIS 5.1 - Visual Studio 6 Interdev EDIT: By "debug" I mean running the project with breakpoints. Interdev doesn't stop at breakpoints.

  Read the article

• Network Sharing Issues

  - by Mark Kramer

  I have two computers I want to have on a network share together (so the laptop can print through the desktop's printer). These are both connected to the same router. (One wired and one wireless) And they both have the same workgroup name. However, when I type "net view" in the command prompt, the only computer that shows up is the computer I type the command into. How do I get these computers to be shared with each other? Update: The tower is running Windows XP, the Laptop is running Windows 7. I have disabled the Firewall on both until I get this set up. Update 2: Typing the command net view on my desktop is acting very strangely. Noe sometimes it only shows itself on the list of computers, sometimes it shows itself and the laptop and sometimes it doesn't work at all and displays system error 6118. I typed net view into the command prompt on the Windows 7 laptop and both computers showed up, so I went to connect to the desktop from the laptop and it said the dekptop could not be found, even though it is showing up int he list of shared computers. Here are supporting pictures (these are coming from the laptop)

  Read the article

• My yum repository able to search packages, but not able to install it in RHEL?

  - by mandy

  I set up yum from dvd. Following is the containts of my .repo file: [dvd] name=Red Hat Enterprise Linux Installation DVD baseurl=file:///media/dvd enabled=0. I'm able to search packages. However while installation I'm getting below error: [root@localhost dvd]# yum install libstdc++.x86_64 Loaded plugins: rhnplugin, security This system is not registered with RHN. RHN support will be disabled. Setting up Install Process Nothing to do My Yum Search output: [root@localhost dvd]# yum search gcc Loaded plugins: rhnplugin, security This system is not registered with RHN. RHN support will be disabled. ============================================================================= Matched: gcc ============================================================================= compat-libgcc-296.i386 : Compatibility 2.96-RH libgcc library compat-libstdc++-296.i386 : Compatibility 2.96-RH standard C++ libraries compat-libstdc++-33.i386 : Compatibility standard C++ libraries compat-libstdc++-33.x86_64 : Compatibility standard C++ libraries cpp.x86_64 : The C Preprocessor. libgcc.i386 : GCC version 4.1 shared support library libgcc.x86_64 : GCC version 4.1 shared support library libgcj.i386 : Java runtime library for gcc libgcj.x86_64 : Java runtime library for gcc libstdc++.i386 : GNU Standard C++ Library libstdc++.x86_64 : GNU Standard C++ Library libtermcap.i386 : A basic system library for accessing the termcap database. libtermcap.x86_64 : A basic system library for accessing the termcap database. Please guide me on this, I want to install gcc on my RHEL.

  Read the article

• Slow connection to Linux MySQL from Windows only (XAMPP)

  - by Josh

  I'm having a problem with a PHP project (using Kohana 3.2 framework) on my Windows 7 64-bit machine connecting to the database. The development database is stored on a Ubuntu Linux server on the local network. Other development machines running OSX and Linux are connecting fine. There are no other Windows development machines to test with. I can access MySQL fine using MySQL Workbench, and other projects (which I believe to be less database heavy) run mostly ok, only occasionally getting timeout messages. I'm constantly getting Maximum execution time of 30 seconds exceeded when functions such as mysql_query() are run in this particular project. Specifically, the Kohana file where the timeout occurs is MODPATH\database\classes\kohana\database\mysql.php [ 186 ]. My local set-up is: Windows 7 Professional 64bit XAMPP 1.7.7 (PHP 5.3.8) The output of uname -a of the Linux server is: Linux peach 2.6.38-11-server #50-Ubuntu SMP Mon Sep 12 21:34:27 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux I've tried the following, with no success: Disabling Windows firewall Switching between using a persistant and normal connection In my.cnf, adding skip-name-resolve Increasing wait_timeout Enabling bind-address I've run out of ideas now, and have no idea how to debug an odd issue like this. Has anyone come across this before, or have any idea how I could find the root of the issue, or what might be the problem?

  Read the article

• How can I add a second hard drive to a previously configured UEFI/ACHI Windows 8 machine?

  - by pflyer

  Recently purchased a new Windows 8 PC. It came with one hard drive. I want to a second hard drive to it. This second hard drive is my data hard drive from my previous computer. However, I have run into issues when the system accesses it. The drive is found in the BIOS. But is not seen by Explorer or Disk Management. I have added the drive to the next available SATA slot: SATA 2. The machine is a UEFI/ACHI based machine. In my reading I have found people documenting the following: 1) adding multiple partitioned hard drives (like mine is) to UEFI based machines is not possible 2) I have seen it suggested that you can only add blank hard drives to UEFI based machines. However, in doing so, I did not have success. I tried to add it as a hard drive with unallocated space and then as a hard drive with a single simple partition. Both attempts failed. My ultimate question: What is the proper procedure for adding a second hard drive to a UEFI/ACHI machine? I do not want to reinstall the OS and start from scratch as I have seen suggested elsewhere. There has to be a way to accomplish this without all that hassle. Thanks in advance for your help.

  Read the article

• Change source address based on destination IP

  - by hgj

  We have several "router" machines that gather a lot of external IP addresses on the same host and redirect, NAT or proxy the traffic to the internal network. They also act as routers for the machines on the internal network. This works fine, however I am unable to make the routing table, so I can change the source address, based on the destination a machine from the internal network want to access. Let's say I have a router, that has public addresses P1 (5.5.5.1/24) and P2 (5.5.5.2/24). All traffic goes through P1, but if necessary, the host is reachable on P2 too. This looks like this and works fine: > ip addr ... 1: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether aa:bb:cc:dd:ee:11 brd ff:ff:ff:ff:ff:ff inet 5.5.5.1/24 brd 5.5.5.255 scope global eth1 inet 5.5.5.2/24 brd 5.5.5.255 scope global secondary eth1:p2 ... Now I want to use P2 as the source address, if I want to access the Google DNS service for example (8.8.8.8). So I add a row in the routing table like: > ip route add 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 > ip route ... default via 5.5.5.254 dev eth1 5.5.5.0/24 dev eth1 proto kernel scope link src 5.5.5.1 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 ... But this does not work. If I ping 8.8.8.8, the host still uses P1 as the source address, and does not use P2 at all for outgoing connections. Am I doing it right? I guess not...

  Read the article

• Developer hardware autonomy in a managed desktop environment [closed]

  - by Troy Hunt

  I’m looking for some feedback on how developer PCs are managed within environments that have a strict managed desktop policy (normally large corporations). For example, many corporate environments control the installation of software and the deployment of patches and virus updates through a centralised channel. This usually means also dictating the OS version and architecture (32 bit versus 64 bit) which will likely also mean standardised hardware configurations. I’m particularly interested in feedback from developers who work in this sort of environment but have a high degree of autonomy over their machines. This might mean choosing your own hardware vendor, OS type and version and perhaps how the machines are built and maintained. I have several specific questions: How do you satisfy the needs of security, governance etc whilst maintaining your autonomy? For example, how do you address concerns about keeping virus definitions and OS patches up to date? Do you have a process for gaining exemption from standard desktop builds and if so, what do you need to demonstrate in order to get this? How have you justified this need to the decision makers? Essentially, what is the benefit to your role as a developer by having this degree of autonomy? Thanks very much everyone. Update: There's a great post from Jean-Paul Boodhoo which addresses the developer tool component of the quesiton here: http://blog.jpboodhoo.com/TheFallacyOfTheStandardizedDeveloperMachineimage.aspx

  Read the article

• XP - ping changes routing table?

  - by Corelgott

  Hey Folks, I have got a real strange behaviour with one of my XP-Sp3 machines. Setup: A Server in the lan (192.168.5.0) proviedes access to all roadwarriors in 10.8.0.0 The DCHP has a static route for all clients pronouncing 192.168.5.235 as gateway for 10.8.0.0 All Clients can ping & access the vpn-machines; everything works like a charm But one Xp-Sp3 is not willing to connect to them. It gets all the same routes as any other sytem in the lan and I trippel-checked - there are no static routes on this machine When I ping any 10.8.0.0 device from this machine, the first two packaged work like a charm; but the next two (and any package after them) fail and get lost. When I look back into the routing table: There is a new route; a special one just for the device I pinged, which points to the right gateway - but which wasn't there earlier... As Long as this route exists the machine can't ping anything on 10.8.0.0. But if I remove the route by hand: The next to ping packages work fine... Has anybody got an idea about that? Anybody every seen such a behaviour? Any hint / help / tip is greatly appreachiated! thx in advance Corelgott Ps: I attach an image of the cmd to clarify things - its in german, but reading a routing table shouldn't be that hard...

  Read the article

• Symantec Antivirus Corporate -- two problems

  - by Alex C.

  We have a Windows network with a domain and about 50 clients. A few months ago, we installed Symantec Antivirus, Corporate Edition ver. 10.1.8.8000. There are two problems. The larger problem is that the software isn't very good at stopping viruses. In the last month, four different machines have become infected with those viruses that masquerade as antivirus software. Two machines I was able to clean with MalWareBytes. The other two were hopeless, and I had to reinstall Windows. Is there something I can do to make the Symantec product more effective? As far as I can tell, it successfully updates definitions nightly and pushes the definitions to the clients. The smaller problem is that the Symantec client applications sometimes initiate scans at random (and inappropriate) times. One of my co-workers complained to me yesterday that her computer was running very slow. I looked at the scan history and found that Symantec had scanned the computer three times during the past two days, and each time during the workday. No threats were found. Not sure why it's doing this, but I'd like it to stop. Any help would be appreciated. Thanks.

  Read the article

• Memory overcommitment on VmWare ESXi 5.0

  - by Tibor

  I would like to understand better the possibilities of VmWare ESXi memory overcommitment. I've read this paper from VmWare, so I am familiar with general concepts, such as hypervisor swapping, memory balooning and page sharing. It seems that a combination of these techniques allows for quite a large degree of overcommitment. However, I am not sure. I am deploying a virtual test lab comprising of 4 identical sets of virtual servers and workstations and a couple of virtual router instances. Overall, I expect to be running around 20 virtual machines with Windows XP, Windows 7 and Ubuntu for workstation hosts as well as CentOS and Windows 2008 Server instances for servers. The problem is, however, that the host machine only has 12GB of RAM and I don't have an option to stuff in some more. I would like to know what is the best option to configure hosts in order to achieve reasonable performance within the constrains. I have these two options: Allocate as little as possible of RAM to each virtual machine. Allocate an extraordinary amount (such as 4 GB per instance) and let the baloon driver do the rest. Something else? Which would work better? Machines will mostly be idle, so I don't have any major performance expectations, but they should run reasonably smoothly nevertheless.

  Read the article

• OpenVPN bridge network from routed clients

  - by gphilip

  I have the following setup: subnet 1 - 10.0.1.0/24 with a machine used as NAT and also running an OpenVPN client subnet 2 - 192.168.1/24 with an OpenVPN server (the server in subnet 1 connect here) subnet 3 - 10.0.2.0/24 that uses the NAT machine (subnet 1) to access the internet, so all non-local traffic is routed there to the eth0 interface The OpenVPN client creates the tun0 interface and appropriate routing so that I can access machines from 192.168.1/24 [root@ip-10-0-1-208 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... Connected to 192.168.1.186. Escape character is '^]'. [root@ip-10-0-1-208 ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.1 10.8.0.5 255.255.255.255 UGH 0 0 0 tun0 10.8.0.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 169.254.169.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 192.168.0.0 10.8.0.5 255.255.0.0 UG 0 0 0 tun0 However, when I try the same from subnet 3, it can't reach that machine. [root@ip-10-0-2-61 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... I suspect that it's because subnet 3 is routed to eth0 on the NAT machine in subnet 1 and it cannot jump to tun0. What's the easiest way to resolve it? I don't want to use iptables. I can't change the routing from machines in subnet 1 because it's done in AWS and so it works only with specific interfaces. Also, the NAT machine gets its IP with DHCP and so bridging is a bit complicated. IP forwarding is set on the NAT machine [root@ip-10-0-1-208 ~]# cat /proc/sys/net/ipv4/ip_forward 1 Thank you!

  Read the article

• PHP on several servers with session-sharing

  - by Etu

  there's certanly other threads about this, but I have one more question. We are about to scale the website at work to have more than one server. And we need to share the sessions between the servers. We have been looking into different solutions, one in memcached and use Memcached as sessionhandler in PHP. That will probably work. And the idea would be to run memcached on every machine and let all webservers access all other servers memcached servers, and then we have shared sessions between the machines, yay. (we have no resources to setup with sticky-sessions yet, that's a later project. we need this running, and we need this running now. and we will loadbalance with DNS for a starter) But then... If I want to take one server down, say, for maintenance, or a server crashes, or whatever reason. I don't want the users to just loose their sessions and have to start from the beginning... That's why we need some kind of replication, which Memcached does not support. Then I found http://repcached.lab.klab.org/ -- which has multi-master replication of memcached, which is great, and is what I want. But does it work with 2 machines? Say 3, 5, 10? For future scaling. I also looked into redishttp://redis.io/ -- which also seems great, but is a bit more "shaky" with the php-session-handler support, and no multi-master-replication. The thing is that I like to use memcached, but I want to be able to power down one of two boxes without loosing half of the sessions. Any suggestions?

  Read the article

• Why am I missing 4GB of RAM on Windows Server 2008 R2 64bit?

  - by Nick G

  I noticed today that a server was very low on memory. It physically has 8GB installed and runs Windows 2008 R2 Standard 64bit. It also hosts 2 virtual machines using HyperV. Server is Dell Poweredge R510. However the host OS reports in task manager that it only has 4GB of RAM, despite actually having 8GB and it being a 64bit OS. Computer properties shows Installed memory: 8.00GB (3.99GB usuable). Why would "usable" be half the real RAM installed under a 64bit OS? Additionally nearly all of the 4GB of visible RAM on the host OS is being used by something without anything showing up in task manager (presumably HyperV as it's allocated 3.6GB to the virtual machines its hosting). However that doesn't explain where the other 4GB has gone which Windows can't even see. Where is my missing 4GB of RAM? Update: Dell OpenManage says this: Total Installed Capacity 8192 MB Total Installed Capacity Available to the OS 4096 MB So looks like Nathan's suggestion of memory mirroring might be correct. I'll have to reboot to check this (I think?) Update 2 OK. So I reboot and I get a message saying "the amount of system memory has changed" (despite not having touched the hardware in a year). Once Windows has booted, all 8GB is visible again. Looks like I probably have a hardware RAM issue (I'll perhaps try reseating it whenever I can chuck everyone off the server next). Thanks for your answers and comments. I was hoping it was going to be the mirrored-RAM option but it seems not - that's not even mentioned in the BIOS.

  Read the article

• unicorn and nginx, went wrong

  - by achempion

  I try to deploy my app via capistrano. It was done, but when I start to nginx and show my site in the browser I see 'We're sorry, but something went wrong.' It is bad. I use unicorn. See my configs https://gist.github.com/3904032 I try to start server via rails s -e prodiction and it's work! I think that this error may be because I can't restart server root@li272-194:~# /etc/init.d/nginx restart Restarting nginx: the configuration file /etc/nginx/nginx.conf syntax is ok configuration file /etc/nginx/nginx.conf test is successful [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: still could not bind() nginx. any ideas? nginx log 2012/10/17 02:57:41 [error] 3271#0: *1 could not find named location "@myapp", client: 91.192.62.77, server: 178.79.153.194, request: "GET / HTTP/1.1", host: "178.79.153.194" 2012/10/17 02:19:08 [crit] 2448#0: *8 connect() to unix:/srv/zarcon/shared/unicorn.sock failed (2: No such file or directory) while connecting to upstream, client: 91.192.62.77, server: zarkon, request: "GET / HTTP/1.1", upstream: "http://unix:/srv/zarcon/shared/unicorn.sock:/", host: "178.79.153.194"

  Read the article

• What hardware would I need (approx) to run ESXi server?

  - by mr.b

  Hi, I am considering to purchase off-the-shelf commodity hardware in order to build server that will host virtual machines using ESXi server. Intended purpose for this server is NOT mission critical tasks. It will have to run perhaps 20-50 Windows XP/Vista/7 virtual machines (in total, but closer to 20 figure). Each guest would have to have 1-2 GB of ram, and probably two-three times more disk space than guest OS needs with clean install and all updates applied (that would be around 6-8 GB for XP, and i believe closer to 10-15 for win7). Those guests will act as a test ground for a new product that is network management software, thus guests will idle most of their time once initially loaded, but if I give them some task to complete, they should be able to perform reasonably well. Now, from what I have learned... CPU is usually not much of an issue (6 cores would do it), memory should not be lacking, but doesn't have to be sum of all guests, because of overcommitment... That leads me to IO, which is, as it seems, the bottleneck. Since I have very little experience with ESXi (and ESX, too) server, I'd like to ask: How much memory could I save by overcommitment, and how does it affect performance? Is 6-core cpu enough to run above described system? Would it be possible to run entire server off two (or even one) SSD drives (to host system virtual disks, with few additional HDDs (2-3) in RAID 0 to be used as secondary storage? I read somewhere that ESXi allows having something like "master image", essentially virtual machine that is "deployed" many times, so that disk space can be saved by having only differences stored by specific guests, instead of copying around whole virtual disks. Is this true, and how can this help me? Are there any other things I need to take into consideration when building this off-the-shelf solution? I should probably mention here that I'm fully aware of issues like SPOF regarding power supply, raid 0, etc, but since it's only a testing ground and not a production system, it's not so important for me. Thanks, B.

  Read the article

• VPN service into 192 network

  - by tophersmith116

  I'm thinking about setting up a security testing lab. I work on a switched network, and that just makes for unnecessary headaches when doing testing. I'd like to create a 192 network with a few machines inside for DBs and AppServers etc. I will need a pivot machine that connects to both the outer network and the 192 (for automation purposes). But I'd like to be able to connect into the 192 network with my own machine from the outer network as the "attacking" machine (rather than have dedicated attack machines inside the 192 network). Therefore, I'd like to have the pivot server be a VPN server as well, so that my machine can VPN into the 192 network from the outer network. First off, is this even possible? Can I have a single computer with two NICs where a VPN service allows remote connections into the 192? Secondly, I'd like to have multiple outer clients connect to the VPN. Does anyone have any suggestions? I've used Hamachi well before, but I've also seen some good stuff from OpenVPN.

  Read the article

• What may the reason of slowness be (see details in message body)?

  - by Ivan

  I've got a really weird situation I'm beating to solve. A performance problem which looks really like an empty waiting sequence set in code (while it probably isn't so). I've got a pretty powerful dedicated server (10 GB RAM, eight Xeon cores, etc) running Ubuntu 10.04 with all the functionality services (except OpenVPN server used to provide secure access to clients) deployed in separate VirtualBox (vboxheadless) machines (one for the company e-mail server, one for web server and one for accounting/crm server (Firebird + proprietary app server working with Delphi-made clients)). CPU load (as "top" says) is almost always near zero. Host system RAM is close to 100% usage but not overloaded (as very little swapping gets used, and freed (by stopping one of VMs) memory doesn't get reused any quickly). Approximately 50% of guests RAM is used. iostat usually shows near zero %util. Network bandwidth seems to be underused. But the accounting/crm client (a Win32 Delphi application run on WinXP machines) software works hell-slow with this server (and works much better using an inside-LAN Windows server). I just can't imagine what can make it be slow if there are so plenty of CPU, RAM, HDD and bandwidth resources available on clients and on the server even in their hardest moments. Saying bandwidth is underused I not only know that clients and the server are connected to the Internet with a bigger channels than really used (which leaves the a chance they may have a bottleneck of a sort on the route between them), I've tested bandwidth between clients and the server by copying files among them.

  Read the article

• How can I measure actual memory usage from my running processes?

  - by NullUser

  I have two servers, server1 and server2. Both of them are identical HP blades, running the exact same OS (RHEL 5.5). Here's the output of free for both of them: ### server1: total used free shared buffers cached Mem: 8017848 2746596 5271252 0 212772 1768800 -/+ buffers/cache: 765024 7252824 Swap: 14188536 0 14188536 ### server2: total used free shared buffers cached Mem: 8017848 4494836 3523012 0 212724 3136568 -/+ buffers/cache: 1145544 6872304 Swap: 14188536 0 14188536 If I understand correctly, server2 is using significantly more memory for disk I/O caching, which still counts as memory used. But both are running the same OS and if I remember correctly, I configured both with the same parameters when they were installed. I did a diff on /etc/sysctl.conf and they are identical. The problem is, I am collecting memory usage and other metrics over a period of time, (eg: vmstat, iostat, etc.) while a load is generated on the system. The memory used for caching is throwing off my calculations on the results. How can I measure actual memory usage from my running processes, rather than system usage? Is used - (buffers + cached) a valid way to measure this?

  Read the article

• Linux file server for an inexperienced admin

  - by Pat

  A charity I volunteer for wants a file server for their mostly Windows machines (about five XP and 7 machines, with some Mac laptops every now and then). For the server, I have a PC with an Intel Core 2 Duo 3GHz proc, 4GB of DDR2 400MHz RAM, and a 500 GB HDD. (I should point out that they do not currently have any server - they are just using Windows to share a folder on one of the PCs.) What is a linux distro that is easy to configure for Windows file serving yet stable and secure enough to protect sensitive data without an expert sysadmin? I'm guessing that a Debian distro would probably fit the security bill, but I don't know of any tailored to novice sysadmins. Also, are there any killer apps for making this easy to administer and set up (as a Windows file server, in particular - this answer is a good example)? Would FreeNAS be sufficient? Once it's all set up, what are the minimum measures I need to take to keep the data secure? I found this somewhat helpful answer, but it's not specific to my question of just getting a secure file server up, running, and maintained.

  Read the article

• Can applications use all of the memory in Windows 8?

  - by Barleyman

  Windows 7 (and Windows Vista) have a built-in limit of not being able to use the last 25% of RAM. You will get a low memory warning when you get close to the limit. Even if you disable that warning, applications will run out of memory and crash since the OS will refuse to allocate memory from that last 25%. That was fine when Vista was designed, when machines had 1 GB of total memory, but is pretty daft for today's 8 GB machines. Yes, the system will run cache, etc. on that extra 2 GB, but running out of memory when you have "merely" 2 GB left.... NB: this has nothing to do with the page file. If you limit the page file to a sensible size like 2 GB, you will still see this behavior. The system will cram the page file to the last byte while refusing to touch that 1/4th of the RAM. Does Windows 8 change this behavior? Is there now some fixed minimum free RAM requirement, like 512 MB, or is it still 25%? Can you actually adjust the low memory limit?

  Read the article

• how to import existing VM in vmware workstation 8 inventory

  - by Wimmel

  I like to add existing vmware (player) virtual machines to the vmware workstation 8 inventory on linux. When I create a new virtual machine, it is stored in /var/lib/vmware/Shared VMs/. But copying new directories to that folder, does not make them appear in the workstation window. I found out, the inventory is stored in /etc/vmware/hostd/vmInventory.xml; <ConfigRoot> <ConfigEntry id="0000"> <objID>1</objID> <vmxCfgPath>/var/lib/vmware/Shared VMs/test 1234/test 1234.vmx</vmxCfgPath> </ConfigEntry> </ConfigRoot> But I don't know if I break anything when adding entries myself, and giving it an unique ID. Besides, adding a large number of VMs this way is a bit cumbersome. On ESX, it was possible to use vmware-cmd -s register, but I don't have a vmware-cmd installed. In another question it was suggested to use vmware converter. But vmware converter 5 (on windows) only allows a destination file location when I select workstation as destination type. When I select vmware infrastructure as destination type, it says the destination is unsupported; it required vmware vcenter server.

  Read the article

• TCP dies on a Linux laptop

  - by Roman Cheplyaka

  Once in several days I have the following problem. My laptop (Debian GNU/Linux testing) suddenly becomes unable to work with TCP connections to the internet. The following things continue to work fine: UDP (DNS), ICMP (ping) — I get instant response TCP connections to other machines in the local network (e.g. I can ssh to a neighbour laptop) everything is ok for other machines in my LAN But when I try TCP connections from my laptop, they time out (no response to SYN packets). Here's a typical curl output: % curl -v google.com * About to connect() to google.com port 80 (#0) * Trying 173.194.39.105... * Connection timed out * Trying 173.194.39.110... * Connection timed out * Trying 173.194.39.97... * Connection timed out * Trying 173.194.39.102... * Timeout * Trying 173.194.39.98... * Timeout * Trying 173.194.39.96... * Timeout * Trying 173.194.39.103... * Timeout * Trying 173.194.39.99... * Timeout * Trying 173.194.39.101... * Timeout * Trying 173.194.39.104... * Timeout * Trying 173.194.39.100... * Timeout * Trying 2a00:1450:400d:803::1009... * Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable * Success * couldn't connect to host * Closing connection #0 curl: (7) Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable Restarting the connection and/or reloading the network card kernel module doesn't help. The only thing that helps is reboot. Clearly something is wrong with my system (everything else works fine), but I have no idea what exactly. I don't know how to reproduce this, but as I said, it happens every several days. My setup is a wireless router that is connected to the ISP via PPPoE. Any advice?

  Read the article

• With puppet, can you have the client ask to be a certain set of roles?

  - by Aitch

  I've recently got my puppetmaster and client up and running and have had the client correctly signed, then requested and applied simple changes, all good. I have a growing number of machines (100). They are not consistently named (historical reasons). They fall into a handful of categories (think of it like: dataserver_type1, dataserver_type2, webserver_type1, webserver_type2....). New instances of these types of machines are added weekly. I don't understand (yet) or cannot see how I can declare a "generic" node of (say) "dataserver_type1" that contains whatever modules it needs, and set something in the client puppet.conf that says "I am a dataserver_type1" without using the hostname/FQDN If I set the node name in the catalog as (say) "my-data-server-type1" - the certified hostname - it picks it up and works. I know you can use patterns for hostnames but as I said, my server names are not consistent, and I can't change them. This seems disingenuous to have to edit a file and manually add a node for each server, when they continue to grow. Edit: Digging deeper, it seems roles may be what I want. But there still seems to be an element whereby the master has contain a list of roles that a specific named server should do. Perhaps what I am asking is, how can a client say "I want to be this role", without the server having to be updated?

  Read the article

< Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >