Search Results

Search found 7606 results on 305 pages for 'tmax dev'.

Page 156/305 | < Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >

• Whys is pdf format used?

  - by dan_vitch

  I will admit that I am new to the tech/dev field. It seems to become a trend that every time I have to work with pdfs a part of me dies. Why is this format as ubiquitous as it seems to be? Is it just non-tech people that prefer pdfs?

  Read the article

• NIC is receiving, but not transmitting at all?

  - by Shtééf

  I'm trying to fix a very strange problem remotely on a machine at a customer site. The machine is a Dell PowerEdge, I believe a 1950 (haven't verified, but the lspci output matches specs I found.) The machine has two similar NICs, identified as Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) by lspci, and using the bnx2 driver. (I suspect these are on-board and on the same controller, which is what I'm accustomed to for this type of machine.) The primary interface eth0 works perfectly, and is in fact how I am ssh'd in. However, the secondary interface eth1 is not transmitting. I can see this in ifconfig output, for example, where the TX field is always 0. However, it is receiving, and tcpdump shows ARP requests coming from the ISP's gateway on the other side. The interface is physically connected to a Siemens BSTU4 modem, configured by the ISP. The link is properly set to 10MBps and full duplex, without negotation, as the ISP requested. A small /30 subnet is configured. For the sake of anonimity, let's say the machine is 3.3.3.2/30, and the ISP's gateway .1. The machine has no firewall settings whatsoever. Even running something like arping -I eth1 3.3.3.1, and running tcpdump alongside, shows no traffic whatsoever being transmitted on the interface. (But the other side keeps steadily sending ARP requests, and that is all that can be seen.) What could be causing this? Here's some output, anonymized, which may hopefully help: $ ethtool eth1 Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised auto-negotiation: No Speed: 10Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off Supports Wake-on: d Wake-on: d Link detected: yes $ ip link show eth1 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:15:c5:xx:xx:xx brd ff:ff:ff:ff:ff:ff $ ip -4 addr show eth1 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 inet 3.3.3.2/30 brd 3.3.3.3 scope global eth1 $ ip -4 route show match 3.3.3.0/30 3.3.3.0/30 dev eth1 proto kernel scope link src 3.3.3.2 default via 10.0.0.5 dev eth0

  Read the article

• Puppet and launchd services?

  - by Joel Westberg

  We have a production environment configured with Puppet, and want to be able to set up a similar environment on our development machines: a mix of Red Hats, Ubuntus and OSX. As might be expected, OSX is the odd man out here, and sadly, I'm having a lot of trouble with getting this to work. My first attempt was using macports, using the following declaration: package { 'rabbitmq-server': ensure => installed, provider => macports, } but this, sadly, generates the following error: Error: /Stage[main]/Rabbitmq/Package[rabbitmq-server]: Could not evaluate: Execution of '/opt/local/bin/port -q installed rabbitmq-server' returned 1: usage: cut -b list [-n] [file ...] cut -c list [file ...] cut -f list [-s] [-d delim] [file ...] while executing "exec dscl -q . -read /Users/$env(SUDO_USER) NFSHomeDirectory | cut -d ' ' -f 2" (procedure "mportinit" line 95) invoked from within "mportinit ui_options global_options global_variations" Next up, I figured I'd give homebrew a try. There is no package provider available by default, but puppet-homebrew seemed promising. Here, I got much farther, and actually managed to get the install to work. package { 'rabbitmq': ensure => installed, provider => brew, } file { "plist": path => "/Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist", source => "/usr/local/opt/rabbitmq/homebrew.mxcl.rabbitmq.plist", ensure => present, owner => root, group => wheel, mode => 0644, } service { "homebrew.mxcl.rabbitmq": enable => true, ensure => running, provider => "launchd", require => [ File["/Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist"] ], } Here, I don't get any error. But RabbitMQ doesn't start either (as it does if I do a manual load with launchctl) [... snip ...] Debug: Executing '/bin/launchctl list' Debug: Executing '/usr/bin/plutil -convert xml1 -o /dev/stdout /Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist' Debug: Executing '/usr/bin/plutil -convert xml1 -o /dev/stdout /var/db/launchd.db/com.apple.launchd/overrides.plist' Debug: /Schedule[weekly]: Skipping device resources because running on a host Debug: /Schedule[puppet]: Skipping device resources because running on a host Debug: Finishing transaction 2248294820 Debug: Storing state Debug: Stored state in 0.01 seconds Finished catalog run in 25.90 seconds What am I doing wrong?

  Read the article

• EC2 EBS drive letter assignment - is it as consistent as UI/API implies?

  - by Michael Neale

  In EC2 EBS, when I attach a device via UI or api, I specify the device name (eg /dev/sdf through sdp). That drive letter is consistent between reboots ? It seems implied that it is (otherwise why would they let me set it).

  Read the article

• Deny login from certain hosts if logging in with specific sql credentials

  - by Dave

  I want to stop some of our developers from connecting to the production sql server using a specific sql account. They have rights to connect through windows authentication with lower rights. They claim that changing the password will affect too many other processes running on our processing machine. So I want to deny access if they're connecting from there dev machines for now. Another way this would work is if I could just allow connections from one specific host.

  Read the article

• How to pipe the output of the serial port to a file in Windows

  - by Necip

  Hello guys, can somebody tell me how to pipe the output of the serial port to a file in Windows? In Linux the command would be: cat /dev/ttyS0 > /opt/logs/Serial.log Thanks in advance

  Read the article

• Is there a plugin/extension to disable CSS on certain sites and not others when browsing?

  - by barfoon

  Hey guys, Is there a plugin/extension to disable CSS on certain sites and not others when browsing? Sort of like the ability featured in web dev toolbar plugins, but selective and automatic. Any ideas? Thanks,

  Read the article

• crontab: question about a special case of the dash character in the time field spec

  - by mdpc

  In the SuSE /etc/crontab the entry to run the cron.{hourly,daily,monthly,weekly} scripts is coded as: -*/15 * * * * root test -x /usr/lib/cron/run-crons && /usr/lib/cron/run-crons /dev/null 2&1 Notice that the very first character of the specification is a dash character (-), and this is NOT a typo. Can somebody explain what the time spec '-*/15' means? BTW, the stuff seems to be running fine. Thanks

  Read the article

• Getting a joystick's path in Windows

  - by Andreas Grech

  On Linux, I can access my joystick with the following path: /dev/input/js0 Is there a similar way I can access my joystick on Windows?

  Read the article

• C++ program to make linux Ubuntu clone windows partition?

  - by saad

  I want to write code in Dev C++ so that when i execute in Ubuntu 8 , it clones my windows 7 from D: partition to its child partitions E:,F: ... i have made my partitions of equal sizes and i have tested by manualy using ntfsclone ,so their will be no problem in cloning. this is part of kiosk system and i hope you understand what i am upto Some reference or help will be appreciated thanks

  Read the article

• How to add Group in mounting drive in fstab

  - by Master

  I am using this to mount drive at startup /dev/sda5 /media/virtual ntfs defaults,umask=700,uid=1 0 0 This is working fine but i need things 1)By this method all the folders inside the virtual folder have same permissions but i want 700 for virtual directory and 777 for all other directories 2)I want that if i can add group as well in the mount command. Just like uid, if i couol add gid as well. Is it possible

  Read the article

• Restart a single apache vhost

  - by snowflake

  I've got an Apache (2) server with several virtual hosts. I currently have mysql db locks problems on one virtual host. A common and practical way to easy release those locks and unlock the site (while the dev team refactor its application to avoid the locks), is to simply restart the apache server. I'm wondering if there is a way to restart the single vhost that is in trouble. Thank you for any comments

  Read the article

• RAW Device mappings

  - by Setesh

  I am new to ESXi, I am going to be using a hard disk attached to my VM with Raw device mappings that connects back to our SAN. What are the recommended options to choose? Where to store the LUN mappings, on the VM or with the Datastore? What compatibility mode to use physical or virtual? We are going to be using this for database server in our dev environment.

  Read the article

• Google Chrome doesn't keep my "allow all cookies" setting

  - by jldupont

  It seems that Google Chrome doesn't keep my "allow all cookies" settings (dev 5.0.322.2) anymore. Google's sites keep on showing: Your browser's cookie functionality is turned off. Please turn it on. [?] but every I perform the prescribed steps, Chrome doesn't keep the configuration! update: I've deleted ~/.config/google-chrome/Default/Preferences and restarted with a clean state. Now it seems to work.

  Read the article

• How to enable Apps in Google Chrome?

  - by Bakhtiyor

  I have downloaded Google Chrome from Dev channel and opening chrome with a --enable-apps parameter but still cann't install google apps. Does anybody know how to install Chrome Apps in a chrome? I have tried to install this Chrome App which is called Calc Lite. This App has been developed just to see Chrome App in action.

  Read the article

• Forgotten LUKS passphrase

  - by Ansh David

  i am stuck with a big problem. I have encrypted my linux drive with LUKS and now I can't remember it. During boot, it prompts me for the passphrase, but I went into troubleshooting mode and deleted the entry from /etc/crypttab so at least I can boot now into my account but that doesn't solve the problem. I can't access my drive /dev/sda5. Can someone please show me a way to crack the passphrase or is there no way around it.

  Read the article

• PHP 5.2 to 5.3 not upgrading, no errors

  - by Webnet

  I'm following this guide: http://atik97.wordpress.com/2010/06/12/how-to-upgrade-to-php-5-3-in-ubuntu-9-10/ I've done all the steps, but it's still showing php 5.2.6 - any ideas? I have also tried -cgi instead of -cli, neither have any effect. update I've tried rebooting the server to see if that would have any effect and unfortunately it didn't update Output of dpkg -l *php*: Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Cfg-files/Unpacked/Failed-cfg/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Hold/Reinst-required/X=both-problems (Status,Err: uppercase=bad) ||/ Name Version Description +++-=============================================-=============================================-========================================================================================================== un libapache2-mod-php4 <none> (no description available) ii libapache2-mod-php5 5.2.6.dfsg.1-3ubuntu4.6 server-side, HTML-embedded scripting language (Apache 2 module) un libapache2-mod-php5filter <none> (no description available) ii php-pear 5.2.6.dfsg.1-3ubuntu4.6 PEAR - PHP Extension and Application Repository un php4-cli <none> (no description available) un php4-dev <none> (no description available) un php4-mysql <none> (no description available) un php4-pear <none> (no description available) ii php5 5.2.6.dfsg.1-3ubuntu4.6 server-side, HTML-embedded scripting language (metapackage) ii php5-cgi 5.2.6.dfsg.1-3ubuntu4.6 server-side, HTML-embedded scripting language (CGI binary) ii php5-cli 5.2.6.dfsg.1-3ubuntu4.6 command-line interpreter for the php5 scripting language ii php5-common 5.2.6.dfsg.1-3ubuntu4.6 Common files for packages built from the php5 source ii php5-curl 5.2.6.dfsg.1-3ubuntu4.6 CURL module for php5 un php5-dev <none> (no description available) ii php5-gd 5.2.6.dfsg.1-3ubuntu4.6 GD module for php5 ii php5-imap 5.2.6-0ubuntu5.1 IMAP module for php5 un php5-json <none> (no description available) ii php5-mcrypt 5.2.6-0ubuntu2 MCrypt module for php5 ii php5-mysql 5.2.6.dfsg.1-3ubuntu4.6 MySQL module for php5 un php5-mysqli <none> (no description available) ii php5-xsl 5.2.6.dfsg.1-3ubuntu4.6 XSL module for php5 un phpapi-20060613+lfs <none> (no description available) ii phpmyadmin 4:3.1.2-1ubuntu0.2 MySQL web administration tool update The following commands and their outputs: grep php53 /etc/apt/sources.list deb http://php53.dotdeb.org stable all deb-src http://php53.dotdeb.org stable all apt-cache search -f "libapache2-mod-php5" http://pastebin.com/XNXdsXYC update I've updated the question with more details on installed packages.

  Read the article

• circumstances where software change leads to device damage

  - by nerorevenge

  Recently I changed a friend's OS from a really virus filled windows 7 to Ubuntu ..but kept changing os's because lsusb wouldn't detect the camera.But after coming back to windows, the camera wasn't detected, though I must point out the device driver for the camera was never found. The Sony 'technician' told me that that since the dev-manager of windows 7 couldn't detect the camera , irregardless of whether the device driver was installed, the software change must have damaged the hardware. I was wondering if there is any truth to it.

  Read the article

• What's the silliest configuration mistake you ever made?

  - by Vivek

  You are a System Admin/Consultant and you have to deploy an application working fine on dev machine, but as soon as you deploy it on the production machine it does not work. What is the silliest configuration mistake you ever made?

  Read the article

• Linux Best Practices

  - by Zac

  I'm a life-long Windows developer switching over to Linux for the first time, and I'm starting off with Ubuntu to ease the learning curve. My new laptop will primarily be a development machine: 6GB RAM, 320 GB HD. I'd like there to be 2 non-root users: (a) Development, which will always be me, and (b) Guest, for anyone else. I assume the root user is added by default, like System Administrator in Windows. (1) I'd like to mount /home to its own partition, but how does this work if I have two user accounts (Development and Guest)? Are there 2 separate /home directories, or do they get shared? Is it possible to allocate more space for Development and only a tiny bit of space for Guest in GRUB2? How?!?! (2) I'm assuming that its okay that all of my development tools (Eclipse & plugins, SVN, JUnit, ant, etc.) and Java will end up getting installed in non-/home directories such as /usr and /opt, but that my Eclipse/SVN workspace will live under my /home directory on a separate partition... any problems, issues, concerns with that? (3) As far as partitioning schemes, nothing too complicated, but not plain Jane either: Boot Partition, 512 MB, in case I want to install other OSes Ubuntu & non-/home file system, 187.5 GB Swap Partition, 12 GB = RAM x 2 /home Partition, 120 GB I don't have any bulky media data (I don't have music or video libraries, this is a lean and mean dev machine) so having 320 GB is like winning the lottery and not knowing what to do with all this space. I figured I'd give a little extra space to the OS/FS partition since I'll be running JEE containers locally and doing a lot of file IO, logging and other memory-instensive operations. Any issues, problems, concerns, suggestions? (4) I was thinking about using ext4; seems to have good filestamping without any space ceiling for me to hit. Any other suggestions for a dev machine? (5) I read somewhere that you need to be careful when you install software as the root user, but I can't remember why. What general caveats do I need to be aware of when doing things (installing packages, making system configurations, etc.) as root vs "Development" user? Thanks!

  Read the article

• upgrade or compile phonon from sources

  - by hyperboreean

  I am trying to compile KDE from sources and I get this error when trying to make kdelibs: Could NOT find Phonon: Found version "4.3.1", but required is at least "4.3.80" I am running Kubuntu karmic ... and I have the latest phonon dev files. How can I upgrade it to the version that kdelibs needs?

  Read the article

• Allowing Apache in Ubuntu to access files in NTFS hard drive

  - by lyrae

  I have LAMP running in Ubuntu. However, my files are located on a separate NTFS hard drive (/media/shared/mysite/). going to http://localhost gives me a 403 how can i, securely, allow apache to read/write the NTFS disk? 'shared' is currently being mounted when system boots. here's the entry in fstab: /dev/sda1 /media/shared ntfs-3g quiet,defaults,locale=en_US.utf8,umask=000 0 0

  Read the article

• How to redirect external web request to localhost's testing server

  - by Ivan Monteiro

  Some web services calls my web application(www.myapplication.com/external_update_handler). I need to test those requests locally, so I'd like to know your opinions about how can I "redirect" those requests to my localhost dev machine(that is outside of my web aplication domain) so I can debug. Probably it's needed a service/server to get those external requests and a desktop application that sends it to localhost:5555/external_update_handler, but I have no idea where to start and simpler options.

  Read the article

• How to mount a drive in Ubuntu from terminal

  - by Mirage

  hi, I want to mount a drive from terminal at start up. At start if i use ls /media then its empty but if i go to computer and then click VM drive there and after that i use ls /media then it shows VM drive . How can i mount that drive at from terminal something like mount VM or how can find the path of VM like /dev/sda or something

  Read the article

• ZFS Recover from Faulted Pool State

  - by nickv2002

  I have a six disk ZFS raidz1 pool and had a recent failure requiring a disk replacement. No problem normally, but this time my server hardware died before I could do the replacement (but after and unrelated to the drive failure as far as I can tell). I was able to get another machine from a friend to rebuild the system, but in the process of moving my drives over I had to swap their cables around a bunch until I got the right configuration where the remaining 5 good disks were seen as online. This process seems to have generated some checksum errors for the pool/raidz. I have the 5 remaining drives set up now and a good drive installed and ready to take the place of the drive that died. However, since my pool state is FAULTED I'm unable to do the replacement. root@zfs:~# zpool replace tank 1298243857915644462 /dev/sdb cannot open 'tank': pool is unavailable Is there any way to recover from this error? I would think that having 5 of the 6 drives online would be enough to rebuild the right data, but that doesn't seem to be enough now. Here's the status log of my pool: root@zfs:~# zpool status tank pool: tank state: FAULTED status: One or more devices could not be used because the label is missing or invalid. There are insufficient replicas for the pool to continue functioning. action: Destroy and re-create the pool from a backup source. see: http://zfsonlinux.org/msg/ZFS-8000-5E scan: none requested config: NAME STATE READ WRITE CKSUM tank FAULTED 0 0 1 corrupted data raidz1-0 ONLINE 0 0 8 sdd ONLINE 0 0 0 sdf ONLINE 0 0 0 sdh ONLINE 0 0 0 1298243857915644462 UNAVAIL 0 0 0 was /dev/sdb1 sde ONLINE 0 0 0 sdg ONLINE 0 0 0 Update (10/31): I tried to export and re-import the array a few times over the past week and wasn't successful. First I tried: zpool import -f -R /tank -N -o readonly=on -F tank That produced this error immediately: cannot import 'tank': I/O error Destroy and re-create the pool from a backup source. I added the '-X' option to the above command to try to make it check the transaction log. I let that run for about 48 hours before giving up because it had completely locked up my machine (I was unable to log in locally or via the network). Now I'm trying a simple zpool import tank command and that seems to run for a while with no output. I'll leave it running overnight to see if it outputs anything.

  Read the article

< Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >