Search Results

Search found 10810 results on 433 pages for 'port forwarding'.

Page 157/433 | < Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >

• Solution for storing sata drives outside of case

  - by Jeffrey Kevin Pry

  I have a system that has 8 sata disks in a software raid 5 array using mdadm. My issue is that I want to move the drives from inside of the computer case in order to cool more efficiently. I have looked all over the web and only seem to find enclosures that hide the drives connectors behind an estata port or some other internal raid controller. Basically what I want is an enclosure or equivalent that I can run independent sata cables to and either power as well, or have it have its own power supply. I have the sata ports on the motherboard available and don't want to limit io by using one port with a multiplier or the like. One final caveat, I am a college student on a budget and don't have a fortune to spend on such an enclosure. Thanks in advance for your help and advice.

  Read the article

• How to set up memcached to use unix socket?

  - by alfish

  While I could use memcached on Debian to use the default 11211 port, but I've had great difficulty setting up unix socket, Form what I'v read, I know that I need to create a memcache.socket and add -s /path/to/memcache.socket -a 0766 To /etc/memcached.conf and comment out the default connection port and IP, i.e. -p 11211 -l 127.0.0.1 However, when I restart memcached I get internal server errors on Drupal site. I'm trying to implement unix sockets to avoid TCP/IP overhead and boost overal memcached performance, however not sure how much performance gain one can expect of this tweak. I appreciate your hints or possibly configs to to resolve this.

  Read the article

• Cable management between multiple racks

  - by RippieUK

  I am in the planning phase of re-cabling our 5 racks in one of our offices and I would like to ask for some guidance on how you go, or would go about managing cables that goes between racks. In our situation we have 5 racks where the furthest to the right is our main patch panel for 300 floor ports. The rack next to it is our main comms rack where main switches and ISP routers are located. the other 3 racks next to the comms rack then all need to connect back to the main comms rack. I am not sure if a 48 port patch panel in each rack would be any good for this scenario? mainly because i am not sure this can be linked back to the main switch with only 1 cable. Would a 48 port switch in each rack be better as you can uplink those back to main switch? Or should we just run cables between racks back to the main switch? Hope someone can offer some guidiance. Thx

  Read the article

• Use same url externally as internally

  - by Nifle

  If I have a web server on my home network I can connect to it from work with http://my.external.ip/whatever/ (assuming NAT and forwarding). Naturally I have a bookmark in my browser that points to http://my.external.ip/whatever/ however when I use that bookmark on my home computer (also behind NAT) the link does not work because my firewall blocks it. (firewall is a old'ish Dlink) What is the best way to fix this issue?

  Read the article

• new ubuntu server installation - java server not receiving packets

  - by James

  I have developed a Java server which listens for UDP packets which come from mobile devices. At the moment, it works correctly if I run my Server on my windows PC. I can receive and respond to the UDP packets sent from my phone (over 3g, not wifi). However, I am trying to run the Server on a different computer which I found lying around my house. I have basically done a clean install of Ubuntu Server edition, updated it, installed the java run time environment and configured port forwarding to allow connections on the appropriate port. I have also tried to disable the firewall. The problem is, it doesn't appear as if the server is receiving any packets and I've exhausted my brain thinking on how to solve/debug the problem. Can anyone suggest to me what the problem might be? or more likely something I can do to help me find out more information about what is going wrong.

  Read the article

• Is Winpcap able to capture all packets going through a Gigabit NIC without missing any packets?

  - by Patrick L

  I want to use Winpcap to capture all network packets going through a Gigabit NIC of a server. Assuming that I am able to utilize the network link up to 100%, the maximum network speed is 1000Mbps. If we exclude the TCP/IP headers, the maximum TCP data rate should be roughly 940Mbps. Let's say I send a 1GB file through the NIC at 940Mbps using TCP destination port 6000. I use Winpcap to capture all network packets going through the NIC and then dump it to a pcap file. If I use Wireshark to analyze the pcap file and then check the sum of packet size for all network packets sent to TCP port 6000, am I able to get exactly 1GB from the pcap file? Thanks.

  Read the article

• IIS web service responds on server, not from remote client

  - by Aharon Manne

  I have installed a web service on a server running IIS (v6, as far as I can tell). There is another service installed, which responds as expected. My service responds correctly when a browser is pointed to localhost, but there is no response when a remote client tries to query the service. Fiddler on the remote client simply reports a timeout. Wireshark on the remote client shows no response at all from the server, no NACK, nothing. Wireshark on the server detects no query at the relevant port (the service is installed on port 8080). There are no relevant entries in the event viewer. Obviously there is some issue of permissions or authentication. I have tried to compare my service to the service that works, but I have not been able to locate relevant parameters. Any help would be greatly appreciated.

  Read the article

• Where do you find the Bash source files of programs in Linux/Mac OSX?

  - by AndrewKS

  I am currently writing some convenience methods for my terminal in my bash_profile and am sure if what I am writing is "the best way". I figure a good way to verify whether what I'm doing is right or not would be to find some source code of more established programs and see how they do it. My question then is, where can I find this code on my Mac? An example is, with Macports installed, where is the source code that opens the port interactive console when I type nothing but "port" in my shell? (I added Linux in the title even though I am on a Mac because I assume the answer would be the same for both) Edit: The answer I am looking for is in terms of which directory relative to the programs will I find their unix scripts.

  Read the article

• Does HyperV allow binding physical NIC on virtual machine with promiscues mode?

  - by MadBoy

  I have HyperV on Windows 2008 Enterprise R2 installed with some Virtual Server running that I wanted to have ISA or NTOP to monitor traffic. I've added additional physical NIC to server and wanted to use this NIC as traffic monitor (I've enabled port mirroring on switch). I can see on physical machine that runs HyperV a lot of traffic coming to the NIC so port mirroring works fine. However in virtual machine even thou I've assigned that NIC to only this one and only server it sees 0 packets. In VWMare Workstation it worked without problem and I could see mirrored traffic on VM. Should this be possible or HyperV is crippled?

  Read the article

• Varnish VCL not allowing two separate IP addresses as backends

  - by Peter Griffin

  Every time I attempt to add an extra back end into our VCL file, it's fails. Here is the DAEMON_OPTS we are running off: DAEMON_OPTS="-a :80 \ -T localhost:6082 \ -f /etc/varnish/custom.vcl \ -u varnish -g varnish \ -S /etc/varnish/secret \ -s malloc,10G" And here is the offending backend(s) backend default { .host = "114.123.456.789"; .port = "8080"; } backend alt { .host = "203.123.456.789"; .port = "80"; } Any Ideas ? Gut feeling is it might need the backends to be set somewhere, but I'm not sure where.

  Read the article

• Get/Assign IP addresses assigned by the DHCP sever with DLink switches in between

  - by Ranjith Kumar

  In our office the setup is like we have a UBUNTU server with DHCP Server connected to all the PCS via 24 port and 8 port DLink switches. How can I find all the PCS(with client name, ip and mac address)in the network?? When I do "vi /var/lib/dhcp3/dhcpd.leases", I get all the ip addresses for the switches. I have used "arp-scan --interface=eth0 --localnet" to get all the IPs and MAC Addresses in my local network. I couldn't find any option to diplay client name. Also I would like to assign particular IP for a particular PC. I have done the changes in the dhcp.conf file but it is not working as they are not directly connected to DHCP-server(DLink switches in between). How can I assign IPs for PCs in this kind of setup. Thanks in advance

  Read the article

• Problem with usb wireless mouse

  - by aiacet

  Recently I have started having problems with my wireless mouse (Wireless Optical Mouse MI-4910D). Sometimes when I start my PC or during a game the pointer/arrow stops moving. When the PC boots the pointer is locked in the center of the screen. If I'm lucky it helps to change the USB wireless adapter from port 1 to port 2 but sometimes this trick doesn't work and I have to restart my PC to get the mouse to work again. Like you can see in the product web page this mouse don't have a driver but only a tool to solve some problems. Thank you in advance to all the "super-users" that reading this question would be help me Ajax

  Read the article

• How to set up Drupal Plugin Manager on MAMP in a secure way?

  - by Andrei

  Hi, I use MAMP PRO as global webserver. First of all, is it a good idea? Secondly, my objective is to run a Drupal website with as easy management as possible. Now I want to use Plugin Manager module to install additional modules and themes for my website. It wants to use ftp for that, and I know that if I open access to FTP port then IT-department guys will come to me and ask to shut it down. So I wonder if there is a way to allow Plugin Manager to install modules, having the port 21 closed somehow?

  Read the article

• Switch 302 redirect to 301 with Apache 2 ProxyPass in front of Tomcat 6

  - by Gearóid

  I'm trying to optimise my site for SEO and it seems as though their is a 302 direct in action for the http requests. I'm hosting my app on a Tomcat 6 server which lies behind an Apache 2 server. I use the ProxyPass method (http://tomcat.apache.org/tomcat-6.0-doc/proxy-howto.html) to forward all requests to port 8080 (the port my app is hosted on). I've seen a lot of advice on how to set the redirect type when using the VirtualHost method but none to do with ProxyPass. The app is a Struts app that forwards users on to index.jsp when they hit the base url. Could this also be the issue? I'm grateful for any help on this one! Cheers!

  Read the article

• How to stop nginx on Mac OS 10.6.3

  - by Alex Kaushovik

  I've installed nginx server on my Mac from MacPorts: sudo port install nginx. Then I followed the recommendation from the port installation console and created the launchd startup item for nginx, then started the server. It works fine (after I renamed nginx.conf.example to nginx.conf and renamed mime.types.example to mime.types), but I couldn't stop it... I tried sudo nginx -s stop - this doesn't stop the server, I can still see "Welcome to nginx!" page in my browser on http://localhost, also I still see master and worker processes of nginx with ps -e | grep nginx. What is the best way to start/stop nginx on Mac? BTW, I've added "daemon off;" into nginx.conf - as recommended by various resources. Thank you.

  Read the article

• How to failover to local account on a cisco switch/router if radius server fails?

  - by 3d1l

  I have the following configuration on a switch that I testing for RADIUS authentication: aaa new-model aaa authenticaton login default group radius local aaa authentication enable default group radius enable aaa authorization exec default group radius local enable secret 5 XXXXXXXXX ! username admin secret 5 XXXXXXXXX ! ip radius source-interface FastEthernet0/1 radius-server host XXX.XXX.XXX.XXX auth-port 1812 acct-port 1813 key XXXXXXXXX radius-server retransmit 3 ! line con 0 line vty 5 15 Radius authentication is working just fine but if the server is not available I can not log into the router with the ADMIN account. What's wrong there? Thanks!

  Read the article

• Keep source IP after NAT

  - by John Miller

  Until today I used a cheapy router so I can share my internet connection and keep a webserver online too, while using NAT. Users IP ($_SERVER['REMOTE_ADDR']) was fine, I was seeing class A IPs of users. But as traffic grown up everyday, I had to install a Linux Server (Debian) to share my Internet Connection, because my old router couldn't keep the traffic anymore. I shared the internet via IPTABLES using NAT, but now, after forwarding port 80 to my webserver, now instead of seeing real users IP, I see my Gateway IP (Linux Internal IP) as any user IP Address. How to solve this issue? I edited my post, so I can paste the rules I'm currently using. #!/bin/sh #I made a script to set the rules #I flush everything here. iptables --flush iptables --table nat --flush iptables --delete-chain iptables --table nat --delete-chain iptables -F iptables -X # I drop everything as a general rule, but this is disabled under testing # iptables -P INPUT DROP # iptables -P OUTPUT DROP # these are the loopback rules iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # here I set the SSH port rules, so I can connect to my server iptables -A INPUT -p tcp --sport 513:65535 --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --sport 22 --dport 513:65535 -m state --state ESTABLISHED -j ACCEPT # These are the forwards for 80 port iptables -t nat -A PREROUTING -p tcp -s 0/0 -d xx.xx.xx.xx --dport 80 -j DNAT --to 192.168.42.3:80 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p tcp -s 192.168.42.3 --sport 80 -j ACCEPT # These are the forwards for bind/dns iptables -t nat -A PREROUTING -p udp -s 0/0 -d xx.xx.xx.xx --dport 53 -j DNAT --to 192.168.42.3:53 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p udp -s 192.168.42.3 --sport 53 -j ACCEPT # And these are the rules so I can share my internet connection iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A FORWARD -i eth0:1 -j ACCEPT If I delete the MASQUERADE part, I see my real IP while echoing it with PHP, but I don't have internet. How to do, to have internet and see my real IP while ports are forwarded too? ** xx.xx.xx.xx - is my public IP. I hid it for security reasons.

  Read the article

• TCP connection between PCs in home wi-fi network

  - by Nordvind

  I want to establish a connection between 2 PCs. Point is to practice in writing client-server applications and similar stuff. I've heard around, that I can access another PC in network by address like "Router IP:port number". Am I right or i got it wrong? So how do I configure router to let connections to certain ports? And what would address look like, if I'm, say, connecting to 80 port on my home server? P.S. Will be grateful for links to some tutorials on this matter, if any.

  Read the article

• Setup IIS 7 as FTP Server that is connectable outside of my local network

  - by Usta

  I was able to setup an FTP site that I was able to access via ftp://127.0.0.1/ or my local(static) ip. To do this I followed these instructions (with the exception that I did not bind to 127.0.0.1 as suggested) http://learn.iis.net/page.aspx/301/creating-a-new-ftp-site-in-iis-7/ I have created a firewall exception for port 20 and 21, and setup port-forwarding on my wireless router. But I can only access the site via local-host, and I need to have a friend have read access to it. So how do I enable remote access to it? (I'd rather not purchase a domain-name) My setup: IIS 7.5 Windows 7 Professional Wireless Network Norton Internet Security 2012 An Internal Static IP Address

  Read the article

• Eventlog entry for allowed connection in Windows Firewall

  - by Jaap

  I was seeing a lot of entries in the eventlog: The Windows Filtering Platform has permitted a connection. Application Information: Process ID: 4 Application Name: System Network Information: Direction: Inbound Source Address: 10.xxx.xxx.xxx Source Port: 80 Destination Address: 10.xxx.xxx.xxx Destination Port: 31773 Protocol: 6 Filter Information: Filter Run-Time ID: 67903 Layer Name: Receive/Accept Layer Run-Time ID: 44 We have a loadbalancer which checks every second to see if the application is still running (a health check). The logs contain large amounts of this kind of entries, which makes the Event Viewer slow and it's difficult to find the more interesting logs. How do I make sure these messages don't end up in the event logs?

  Read the article

• Proxy Error 502 "Reason: Error reading from remote server" with Apache 2.2.3 (Debian) mod_proxy and Jetty 6.1.18

  - by Martin

  Apache is receiving requests at port :80 and proxying them to Jetty at port :8080 The proxy server received an invalid response from an upstream server The proxy server could not handle the request GET /. My dilemma: Everything works fine normally (fast requests, few seconds or few tens of seconds long requests are processed ok). Problems occur when request processing takes long (few minutes?). If I issue request instead directly to Jetty at port :8080 the request is processed OK. So problem is likely to sit somewhere between Apache and Jetty where I am using mod_proxy. How to solve this? I have already tried some "tricks" related to KeepAlive settings, without luck. Here is my current configuration, any suggestions? #keepalive Off ## I have tried this, does not help #SetEnv force-proxy-request-1.0 1 ## I have tried this, does not help #SetEnv proxy-nokeepalive 1 ## I have tried this, does not help #SetEnv proxy-initial-not-pooled 1 ## I have tried this, does not help KeepAlive 20 ## I have tried this, does not help KeepAliveTimeout 600 ## I have tried this, does not help ProxyTimeout 600 ## I have tried this, does not help NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] ServerName www.mydomain.fi ServerAlias mydomain.fi mydomain.com mydomain www.mydomain.com ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests Off ProxyPass / http://www.mydomain.fi:8080/ retry=1 acquire=3000 timeout=600 ProxyPassReverse / http://www.mydomain.fi:8080/ RewriteEngine On RewriteCond %{SERVER_NAME} !^www\.mydomain\.fi RewriteRule /(.*) http://www.mydomain.fi/$1 [redirect=301L] ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On </VirtualHost> Here is also the debug log from a failing request: 74.125.43.99 - - [29/Sep/2010:20:15:40 +0300] "GET /?wicket:bookmarkablePage=newWindow:com.mydomain.view.application.reports.SaveReportPage HTTP/1.1" 502 355 "https://www.mydomain.fi/?wicket:interface=:0:2:::" "Mozilla/5.0 (Windows; U; Windows NT 6.1; fi; rv:1.9.2.10) Gecko/20100914 Firefox/3.6.10" [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: error reading status line from remote server www.mydomain.fi, referer: https://www.mydomain.fi/?wicket:interface=:0:2::: [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: Error reading from remote server returned by /, referer: https://www.mydomain.fi/?wicket:interface=:0:2:::

  Read the article

• Reverse proxy using hop and RDP

  - by Sergei

  I am trying to connect from Vista to XP using RDP via reverse proxy using putty and an intermidiate host. There are myriad articles on the internet how to do it using vnc, ssh servers, winsshd, etc, but I can't find anything that helps me in this specific case. What I have: Windows XP host behind the firewall - 'destination' linux host running ssh on the internet - 'intermediate' windows host behind the firewall - 'source' All I want to do is open reverse tunnel from destination to intermidiate and use this tunnel for connecting back from the source. That should be simple to setup, however I just cannot make it. This is what I do: On 'destination', open putty session, create tunnel to 'intermediate' using following settings: source port 3389, destination is 'source:33389', direction is local On 'source', open putty session, create tunnel to 'intermediate'using following settings: source port 33389, destination is 'destination:33389', direction is local Finally, on source, open termnal services client and connect it to localhost:33389.Unfortunately it seems like packets do go somewhere but eventually client times out. Am I totally misunderstanding the concept? Please help!

  Read the article

• how do I set up a virtual host (it's not working, and I've done everything right)

  - by piratepartypumpkin

  My router redirects port 80 to port 8080. My router works fine and my domain name is routed properly. This is my virtual hosts file: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /home/admins/lampstack-5.3.16-0/apps/wordpress ServerName example.com ServerAlias www.example.com </VirtualHost> I can access my website by entering "mywebsite.com:8080" but I cannot access it by entering "mywebsite.com" For further information, this is a part of my httpd.conf: Listen 8080 Servername localhost:8080 DocumentRoot "/home/admins/lampstack-5.3.16-0/apache2/htdocs <Directory /> Options FollowSymLinks AllowOverride None Order deny, allow deny from all </Directory> <Directory "/home/admins/lampstack-5.3.16-0/apache2/htdocs"> Options FollowSymLinks AllowOverride None Order allow, deny allow from all </Directory>

  Read the article

• dd-wrt switch for PfSense

  - by Kmao

  I currently have eth2 on my pfsense set up, and configured as 192.168.1.1, it has dhcp setup with allocation being 192.168.1.10 - 192.168.1.245. On my dd-wrt box, i disabled the WAN, and set it to act as a port for the switch. I disabled dhcp, dnsmasq, spi firewall, Wlan0 and set a static IP for the router being 192.168.1.10 Pfsense is plugged into lan0 and pc plugged into lan1 (wan port is empty) I have followed a few different guides, but i can't seem to get my router to act as a switch. Anyone have success using DD-WRT as a switch while using pfsense as your dhcp/dns/gateway. Any advice would help :)

  Read the article

• PHP hits 100% CPU and eats RAM at the same time Monday to Friday

  - by Daniel Samuels

  We run a learning platform for primary schools here in the UK and it's all been running extremely well. However at around 4PM Monday to Friday we see the same issue arise -- 1-2 PHP threads will spike to 100% CPU and gradually start eating up RAM until the server(s) fall over. 98%+ of our requests are HTTPS, these come into our Layer 7 load balancer which then decrypts the SSL data, adds the X-HTTP-Forwarded-For header and forwards the data onto an application server (we have 2 of those at the moment) on port 80. Our application servers have Varnish on port 80 which takes in the request from the load balancer and passes the request through to Nginx on port 81. Nginx then works out which 'vhost' it needs to use and passes any PHP processing through to PHP-CGI which is listening on a socket (managed through spawn-fcgi). There's an instance of Memcached running too, MySQL runs on a separate server / slave setup. Throughout the day the load will typically go no higher than 0.8 on either of the application servers, however at around 4PM our problem arises. I've managed to run strace on a few of the actual threads when they cause the problem and I always see the same thing: stat("/usr/share/zoneinfo/Europe/London", {st_mode=S_IFREG|0644,st_size=3661, ...}) = 0 stat("/usr/share/zoneinfo/Europe/London", {st_mode=S_IFREG|0644,st_size=3661, ...}) = 0 This is repeated infinitely and never stops until you SEGKILL the process or oomkiller kills it. There are no cron jobs scheduled to run at that time and I don't have any way of seeing exactly what Nginx request is associated with the PHP process which is running. We are running PHP 5.3.14 which we upgraded to from 5.3.8 last week to rule out the older version being the problem. This issue has been going on a few months now and we have no idea what is causing it. We deploy our software very frequently, so it's difficult to track down a specific release which may have started the problem - especially as we do not know the date of the first occurrence of this issue. Varnish is version 3.0.1, Nginx is 1.0.6 (which I understand is about a year old now), our servers are running CentOS release 5.7 (Final) they have Intel i3 540s at 3.07Ghz and 8GB of RAM. There's a discussion on the Debian mailing list about something very similar, you can find that here. Has anyone seen anything like this in the past, does anyone have any ideas or suggestions? Are there a way of linking an Nginx request directly to a PHP thread? Is there a better way of seeing what the PHP process is doing? (I've seen GDB mentioned, though I'll have to recompile PHP) Thanks!

  Read the article

< Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >