Search Results

Search found 4846 results on 194 pages for 'rpg master'.

Page 157/194 | < Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • Registry remotley hacked win 7 need help tracking the perp

    - by user577229
    I was writing some .VBS code at thhe office that would allow certain file extensions to be downloaded without a warning dialog on a w7x32 system. The system I was writing this on is in a lab on a segmented subnet. All web access is via a proxy server. The only means of accessing my machine is via the internet or from within the labs MSFT AD domain. While writing and testing my code I found a message of sorts. Upon refresing the registry to verify my code changed a dword, instead the message HELLO was written and visible in regedit where the dword value wass called for. I took a screen shot and proceeded to edit my code. This same weird behavior occurred last time I was writing registry code except on another internal server. I understand that remote registry access exists for windows systems. I will block this immediately once I return to the office. What I want to know is, can I trace who made this connection? How would I do this? I suspect the cause of this is the cause of other "odd" behaviors I'm experiencing at work such as losing control of my input director master control for over an hour and unchanged code that all of a sudden fails for no logical region. These failures occur at funny times, whenver I'm about to give a demonstration of my test code. I know this sounds crazy however knowledge of the registry component makes this believable. Once the registry can be accessed, the entire system is compromised. Any help or sanity checking is appreciated.

    Read the article

  • keepalived issues on xen domU

    - by David Cournapeau
    Hi, I cannot manage to run keepalived correctly on xen domU. I am following this link for configuration, and it works great on some local VM (running with KVM). If I set up the exact same configuration, but on xen domU, it does not work: both servers do not see each other and decide to be master (10.120.100.99 being the virtual IP) $ sudo ip addr sh eth0 # host1 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:16:3e:78:f5:31 brd ff:ff:ff:ff:ff:ff inet 10.120.100.104/24 brd 10.120.100.255 scope global eth0 inet 10.120.100.99/32 scope global eth0 inet6 fe80::216:3eff:fe78:f531/64 scope link valid_lft forever preferred_lft forever $ sudo ip addr sh eth0 # host2 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:16:3e:51:36:20 brd ff:ff:ff:ff:ff:ff inet 10.120.100.105/24 brd 10.120.100.255 scope global eth0 inet 10.120.100.99/32 scope global eth0 inet6 fe80::216:3eff:fe51:3620/64 scope link valid_lft forever preferred_lft forever Is there a way I could debug this - it seems some people are able to use keepalived on xen following some mailing list, but without much info on their config.

    Read the article

  • Change Windows Authentication user for Sql Server Management Studio

    - by Asmor
    We're using Sql Server 2005 with Windows Authentication setup. So normally, when you log in using e.g. Sql Server Management Studio, it forces you to log in at MACHINE_NAME\Username. Anyways, on this one particular computer, the person said they had to make a new account called User01 to do something and showed me where she'd created it under security in the "master" system database. And so now when she logs in, it's listed as MACHINE_NAME\User01 (not the actual Windows user name). It's still set to Windows Authentication, though, and I'm unable to change the login name. Now here's where the real problem comes in... I didn't realize that she was being logged in under this user name at the time, and I disabled it to see what would happen. Now I can't log into the server under her account. I created a new account in Windows called test, and as expected SSMS had the username as MACHINE_NAME\test, and I was able to log in fine. However, the area where the User01 account was listed is not visible to me as far as I can tell and so I can't reenable it. I also tried running the following query: alter login User01 ENABLE And got this error: Msg 15151, Level 16, State 1, Line 1 Cannot alter the login 'User01', because it does not exist or you do not have permission. So in a nutshell, ideally I'd like to reenable User01 somehow, just to get things back to where they used to be. Failing that, how can I force SSMS to log in using the Windows account name as it should be, rather than trying to use User01?

    Read the article

  • Wireless disconnects every 30 minutes

    - by Kez
    I have had a look through all the related questions and I get the feeling my problem is unique. My wireless connection disconnects every 30 minutes, for maybe 1 to 3 seconds. If I am browsing the web while it happens, I get the page cannot be displayed error message. I have checked the event logs as I was curious to know if there was anything in there. There is. Event 8033: BROWSER - The browser has forced an election on network \Device\NetBT_Tcpip_{B919CC30-25A9-45DD-A09F-549A6262FC9E} because a master browser was stopped. Reported exactly every 30 minutes which coincides with my wireless problem. I am running Windows 7 Ultimate, 32-bit. My wireless is Realtek RTL8187 integrated into a ASUS P5K-E/Wifi motherboard. It is on a workgroup and has never been on a domain. This problem does not affect any other computers. Wireless reception is great, and I have ensured that the wireless unit is transmitting on a frequency not used by any nearby wireless basestations. How can I fix this pesky problem?

    Read the article

  • Samba4/Ubuntu Shares Incorrectly Available to All Users

    - by Dan
    I've got my Ubuntu server working with Samba4 and got it set up as the Primary domain controller on my network with AD and all that goodness. However, I'm trying to get my Samba configuration to work with the users and groups I've defined with the Active Directory tools from Windows. For instance, I've got a share X which I want users A and B (as part of the 'management' group, known as LLGrpManager in my setup) to see, but no body else. However, after making changes to the configuration, restarting Samba, I test by connecting to the share with my Mac over Samba as user 'C' which isn't part of the management group, and I can, incorrectly, see the X share. I've tried alsorts of combinations of specifying the group with no luck at all. I've got a feeling that my global config might be too lenient or something to do with file permissions but being a bit green, I'm without clue. My /etc/samba/smb.conf # Global parameters [global] server role = domain controller server string = Office Server workgroup = LLDOMAIN realm = lldomain.local netbios name = DUMBO passdb backend = samba4 logon path = \\%L\profiles\%U logon drive = L: log file = /var/log/samba/%m.log max log size = 50 security = ads domain logons = yes domain master = auto usershare allow guests = no valid users = %S [netlogon] path = /var/lib/samba/sysvol/lldomain.local/scripts read only = no guest ok = no [sysvol] path = /var/lib/samba/sysvol read only = No guest ok = no valid users = @LLDOMAIN\LLGrpManager [ShareX] path = /data comment = Entire Data Volume guest ok = no comment = Entire Data Volume guest ok = no valid users = @LLDOMAIN\LLGrpManager admin users = @LLDOMAIN\LLGrpManager browsable = no inherit acls = yes inherit permissions = yes ... My /etc/nsswitch.conf I've also instructed the system to use the nss winbind library when searching for users or groups by adding the stanza passwd and group in /etc/nsswitch.conf: passwd: compat winbind group: compat winbind shadow: compat Permissions on the folder in question drwxrwxrwt 8 root root 4.0K Oct 28 19:11 data

    Read the article

  • How do I create an MBR on a USB stick using DD command line tool

    - by Lana Miller
    Okay I'm trying to create a BOOTABLE Windows7 image on a USB key from a Mac running Lion. My image is .iso format. I tried: sudo dd if=/Users/myusername/Win7.iso of=/dev/disk1 bs=1m And this succeeded in writing the files, except in DISK UTILITY on the mac, it shows the partition type as GUID Partition Table and not 'Master Boor Record'. Booting the key on my Vista computer yields the error "No boot sector on USB Device' From what I can tell, bs=1m in the DD command should have left 1 Megabyte for the boot sector, but for some reason this area of the USB Key is not set up correctly so that it will boot How can I fix this, or correctly use dd to write a bootable cd image such that it is now a bootable usb drive? Note: in the instructions I read about, they recommended renaming my Win7.iso to Win7.dmg before using DD, which made absolutely no sense to me, so I didn't do it. I could try with that step now, but it takes 1.99 hours to write the image to the USB drive so there is a huge penalty to trial and error here. Thank you.

    Read the article

  • DNS failover in a two datacenter scenario

    - by wanson
    I'm trying to implement a low-cost solution for website high availability. I'm looking for the downsides of the following scenario: I have two servers with the same configuration, content, mysql replication (dual-master). They are in different datacenters - let's call them serverA and serverB. Users use serverA - serverB is more like a backup. Now, I want to use DNS failover, to switch users from serverA to serverB when serverA goes down. My idea is that I setup DNS servers (bind/powerdns) on serverA and serverB - let's call them ns1.website.com and ns2.website.com (assuming I own website.com). Then I configure my domain to use them as its nameservers. Both DNS servers will return serverA IP as my website's IP. If serverA goes down I can (either manually or automatically from serverB) change configuration of serverB's DNS, to return IP of serverB as website's IP. Of course the TTL will be low, as it's supposed to be in DNS failovers. I know that it may take some time to switch to serverB (DNS ttl, time to detect serverA failure, serverB DNS reconfiguration etc), and that some small part of users won't use serverB anyway. And I'm OK with that. But what are other downsides of such an approach? An alternative scenario is that ns1.website.com will return serverA IP as website's IP, and ns2.website.com will return serverB IP as website's IP. But AFAIK clients not always use primary nameserver and sometimes would use secondary one. So some small part of users would use serverB instead of serverA which is not quite what I'd like. Can you confirm that DNS clients behave like that and can you tell what percentage of clients would possibly use serverB instead of serverA (statistically)? This one also has the downside that when serverA goes back up, it will be automatically used as website's primary server, which is also a bad situation (cold cache, mysql replication could fail in the meantime etc). So I'm adding it only as a theoretical alternative. I was thinking about using some professional DNS failover companies but they charge for the number of DNS requests and the fees are very high (why?)

    Read the article

  • What is a long-term strategy to deal with CPU fan dust in my home office?

    - by PaulG
    There are numerous discussions of CPU overheating and how sometimes this can be corrected by removing the dust from the CPU fan. I have read many of these, but I can't find anyone expressing a long-term strategy to deal with this problem. There are some suggestions here, for example, about how often the inside of the computer should be dusted. But I find this generally unsatisfactory. As it stands, in my rather dusty house (heated by a wood stove, with no central air circulation), I need to vacuum out the CPU fan every 3 to 4 months. At high CPU load, this can make a difference between 65C and 100C. I'm tired of hauling out the vacuum every time I anticipate high CPU load. What steps can I take to deal with this systematically in the long-term? Moving my high CPU load computing to the cloud is not a realistic option. Neither is vacuuming my home office more than once a week! (Details: my computer is on the floor in a Cooler Master HAF922 case, and uses an Intel CPU fan on an i7 chip) EDIT: While this would definitely solve the problem (submerging motherboard in mineral oil), it is a bit of an expensive solution.

    Read the article

  • Why I cannot copy install.wim from Windows 7 ISO to USB (in linux env)

    - by fastreload
    I need to make a USB bootable disk of Windows 7 ISO. My USB is formatted to NTFS, ISO is not corrupt. I can copy install.wim elsewhere but I cannot copy it to USB. I even tried rsync. rsync error sources/install.wim rsync: writefd_unbuffered failed to write 4 bytes to socket [sender]: Broken pipe (32) rsync: write failed on "/media/52E866F5450158A4/sources/install.wim": Input/output error (5) rsync error: error in file IO (code 11) at receiver.c(322) [receiver=3.0.8] Stat for windows.vim File: `X15-65732 (2)/sources/install.wim' Size: 2188587580 Blocks: 4274600 IO Block: 4096 regular file Device: 801h/2049d Inode: 671984 Links: 1 Access: (0664/-rw-rw-r--) Uid: ( 1000/ umur) Gid: ( 1000/ umur) Access: 2011-10-17 22:59:54.754619736 +0300 Modify: 2009-07-14 12:26:40.000000000 +0300 Change: 2011-10-17 22:55:47.327358410 +0300 fdisk -l Disk /dev/sdd: 8103 MB, 8103395328 bytes 196 heads, 32 sectors/track, 2523 cylinders, total 15826944 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdd1 * 32 15826943 7913456 7 HPFS/NTFS/exFAT hdparm -I /dev/sdd: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ATA device, with non-removable media Model Number: UF?F?A????U]r???U u??tF?f?`~ Serial Number: ?@??~| Firmware Revision: ????V? Media Serial Num: $I?vnladip raititnot baelErrrol aoidgn Media Manufacturer: o eparitgns syetmiM Standards: Used: unknown (minor revision code 0x0c75) Supported: 12 8 6 Likely used: 12 Configuration: Logical max current cylinders 17218 0 heads 0 0 sectors/track 128 0 -- Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 0 MBytes device size with M = 1000*1000: 0 MBytes cache/buffer size = unknown Capabilities: IORDY(may be)(cannot be disabled) Queue depth: 11 Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 0 Current = ? Recommended acoustic management value: 254, current value: 62 DMA: not supported PIO: unknown * reserved 69[0] * reserved 69[1] * reserved 69[3] * reserved 69[4] * reserved 69[7] Security: Master password revision code = 60253 not supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 71112min for SECURITY ERASE UNIT. 172min for ENHANCED SECURITY ERASE UNIT. Integrity word not set (found 0xaa55, expected 0x80a5)

    Read the article

  • SSH multi-hop connections with netcat mode proxy

    - by aef
    Since OpenSSH 5.4 there is a new feature called natcat mode, which allows you to bind STDIN and STDOUT of local SSH client to a TCP port accessible through the remote SSH server. This mode is enabled by simply calling ssh -W [HOST]:[PORT] Theoretically this should be ideal for use in the ProxyCommand setting in per-host SSH configurations, which was previously often used with the nc (netcat) command. ProxyCommand allows you to configure a machine as proxy between you local machine and the target SSH server, for example if the target SSH server is hidden behind a firewall. The problem now is, that instead of working, it throws a cryptic error message in my face: Bad packet length 1397966893. Disconnecting: Packet corrupt Here is an excerpt from my ~/.ssh/config: Host * Protocol 2 ControlMaster auto ControlPath ~/.ssh/cm_socket/%r@%h:%p ControlPersist 4h Host proxy-host proxy-host.my-domain.tld HostName proxy-host.my-domain.tld ForwardAgent yes Host target-server target-server.my-domain.tld HostName target-server.my-domain.tld ProxyCommand ssh -W %h:%p proxy-host ForwardAgent yes As you can see here, I'm using the ControlMaster feature so I don't have to open more than one SSH connection per-host. The client machine I tested this with is an Ubuntu 11.10 (x86_64) and both proxy-host and target-server are Debian Wheezy Beta 3 (x86_64) machines. The error happens when I call ssh target-server. When I call it with the -v flag, here is what I get additionally: OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /home/aef/.ssh/config debug1: Applying options for * debug1: Applying options for target-server.my-domain.tld debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: auto-mux: Trying existing master debug1: Control socket "/home/aef/.ssh/cm_socket/[email protected]:22" does not exist debug1: Executing proxy command: exec ssh -W target-server.my-domain.tld:22 proxy-host.my-domain.tld debug1: identity file /home/aef/.ssh/id_rsa type -1 debug1: identity file /home/aef/.ssh/id_rsa-cert type -1 debug1: identity file /home/aef/.ssh/id_dsa type -1 debug1: identity file /home/aef/.ssh/id_dsa-cert type -1 debug1: identity file /home/aef/.ssh/id_ecdsa type -1 debug1: identity file /home/aef/.ssh/id_ecdsa-cert type -1 debug1: permanently_drop_suid: 1000 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.0p1 Debian-3 debug1: match: OpenSSH_6.0p1 Debian-3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8p1 Debian-7ubuntu1 debug1: SSH2_MSG_KEXINIT sent Bad packet length 1397966893. Disconnecting: Packet corrupt

    Read the article

  • samba joined to AD canot see users when in the security tab on client

    - by Jonathan
    I've got samba joined via kerberos and winbindd to our AD network and user authentication and everything else is working great. However when I try to add users/groups to file permissions it tells me they are not found. All the users groups show up fine with getent so I'm not sure why they are not showing up. Here is my smb.conf and I would much appreciate any help with this. #GLOBAL PARAMETERS [global] socket options = TCP_NODELAY IPTOS_LOWDELAY SO_KEEPALIVE SO_RCVBUF=11264 SO_SNDBUF=11264 workgroup = [hidden] realm = [hidden] preferred master = no server string = xerxes web/file server security = ADS encrypt passwords = yes log level = 3 log file = /var/log/samba/%m max log size = 50 printcap name = cups printing = cups winbind enum users = Yes winbind enum groups = Yes winbind use default domain = Yes winbind nested groups = Yes winbind separator = + winbind refresh tickets = yes idmap uid = 1600-20000 idmap gid = 1600-20000 template primary group = "Domain Users" template shell = /bin/bash kerberos method = system keytab nt acl support = yes [homes] comment = Home Direcotries valid users = %S read only = No browseable = No create mask = 0770 directory mask = 0770 force create mode = 0660 force directory mode = 2770 inherit owner = no [test] comment = Test path=/mnt/test writeable=yes valid users = %s create mask = 0770 directory mask = 0770 force create mode = 0660 force directory mode = 2770 inherit owner = no [printers] comment = All Printers path = /var/spool/cups browseable = no printable = yes

    Read the article

  • MSSQL Timing out, a couple of questions...

    - by user29000
    Hi, About once a week, my MSSQL server is timing out, or rather the machine runs out of RAM. This morning it reached 3.9GB of the available 4, with MSSQL taking up 2.5GB. I'm concerned that i've not configured SQL to release memory as it should, so I ran sp_who2 while the timeouts were occuring to see what process were running. If i could post the CSV datafile i would, however, there were 85 processes in total, mostly related to the Full Text service: FT Gatherer - About 35 of these running under the 'sa' account against the master database with status of either sleeping or background, many were dependant on other processes. Is that normal? MySite database - There were only 5 processes for the one active site/database and all were either sleeping or suspended - but their lastBatch dates were set to 1/12/2020. Is that normal? The datbase is only about 20mb in size the traffic levels are very low, so i'm thinking of maybe limiting the amount of RAM SQL has access to (from unlimted to maybe 2GB). Any thoughts / advise would be appreciated. Mny thanks Ben

    Read the article

  • New build won't boot: some fans turning, no beep or video

    - by Dave
    When my new system is powered up, the case fan and power supply fans turn fine. The CPU fan twitches, but never gets going. Although I've heard that with AMDs and Gigabyte motherboards that is not necessary a problem. Hard drive is spinning. However, there is absolutely no indication that anything else is happening. The motherboard, as far as I can tell, does not have an internal speaker, but I harvested one from another machine and plugged it in and still no beeps at all. The monitor screen stays black, on both the integrated VGA and DVI. This is a brand new build, and has never successfully booted. My parts are: AMD Athlon II X2 245 Regor 2.9GHz Socket AM3 65W Dual-Core Processor Model ADX245OCGQBOX - includes CPU cooler) GIGABYTE GA-MA785GPMT-UD2H AM3 AMD 785G HDMI Micro ATX AMD Motherboard - Retail G.SKILL Ripjaws Series 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) Desktop Memory Model F3-10666CL8D-4GBRM - Retail CORSAIR CMPSU-400CX 400W ATX12V V2.2 80 PLUS Certified Compatible with Core i7 Power Supply - Retail SAMSUNG Spinpoint F3 HD502HJ 500GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive COOLER MASTER Elite 341 RC-341C-KKN1-GP Black Steel MicroATX Mid Tower Computer Case - Retail I also have a DVD burner, but it acts the same whether that is plugged in or not. I'm using the on board video. What I've tried so far: I've switched power supplies, with no difference. I've tried different monitors (of which all are working on other machines) with no difference. I have tried putting it one memory module at a time, with no difference. I have tried the absolute minimum I can think of (power supply into motherboard, power button ONLY plugged into front panel, CPU fan plugged in), with no difference. I appreciate any ideas anyone might have. Do I need to RMA the motherboard? This is my first build, so there might be something obvious. I was very careful in assembly with static; I'm confident nothing was zapped during assembly.

    Read the article

  • CentOS vps is randomly rebooting

    - by develroot
    I have a centos vps (Parallels Virtuozzo container) which has been running for months. However, a few days ago it started to randomly reboot itself, and i can't find out why. And the biggest problem that i don't understand is that it takes 40 minutes to reboot (as far as i can see in the logs) root ~ # cat /var/log/messages | grep shutdown Oct 11 13:52:11 vps27 shutdown[23968]: shutting down for system halt Oct 14 14:55:17 vps27 shutdown[30662]: shutting down for system halt Oct 15 06:21:23 vps27 shutdown[20157]: shutting down for system halt And notice the time difference between shutdown and xinetd's start: Oct 15 06:21:23 vps27 shutdown[20157]: shutting down for system halt Oct 15 06:21:24 vps27 init: Switching to runlevel: 0 Oct 15 06:21:27 vps27 saslauthd[30614]: server_exit : master exited: 30614 Oct 15 06:21:38 vps27 named[30661]: shutting down Oct 15 06:21:47 vps27 exiting on signal 15 Oct 15 07:04:34 vps27 syslogd 1.4.1: restart. Oct 15 07:05:06 vps27 xinetd[1471]: xinetd Version 2.3.14 started with libwrap loadavg labeled-networking options compiled in. Oct 15 07:05:06 vps27 xinetd[1471]: Started working: 0 available services And here's what Parallels Power Panel says in terms of Status Changes: Time Old Status Status Obtained Oct 15, 2011 06:23:46 AM Mounted Down Oct 15, 2011 06:22:31 AM Running Mounted Oct 14, 2011 03:06:48 PM Starting Running Oct 14, 2011 03:06:23 PM Down Starting Oct 14, 2011 03:06:08 PM Mounted Down Oct 14, 2011 02:58:24 PM Running Mounted For some reason it's getting into Mounting mode and then restarts itself. The only problem that i can imagine is disk space utilization, which is now 84%. But can that be a reson for system halt? Time Category Details Type Parameter Oct 15, 2011 07:08:33 AM Resource Resource counter_disk_share_used yellow alert on environment vps27 current value: 82 soft limit: 85 hard limit: 95 Yellow zone counter_disk_share_used Oct 15, 2011 06:27:23 AM Resource Resource counter_disk_share_used yellow alert on environment vps27 current value: 82 soft limit: 85 hard limit: 95 Yellow zone counter_disk_share_used Oct 15, 2011 06:23:50 AM Resource Resource counter_disk_share_used green alert on environment vps27 current value: 0 soft limit: hard limit: 0 Green zone counter_disk_share_used Oct 14, 2011 03:06:24 PM Resource Resource counter_disk_share_used yellow alert on environment vps27 current value: 83 soft limit: 85 hard limit: 95 Yellow zone counter_disk_share_used Oct 14, 2011 03:05:50 PM Resource Resource counter_disk_share_used green alert on environment vps27 current value: 0 soft limit: hard limit: 0 Green zone counter_disk_share_used

    Read the article

  • SMTP message rate control on Ubuntu 8.04, preferably with postfix

    - by TimDaMan
    Maybe I am chasing a bug but I am trying to set up a smtp proxy of sorts. I have a postfix server which receives all the email for a collection of servers/clients. It them uses a smarthost (relayhost=...) to forward it's mail to our corporate MTA. I would like to limit the number of messages an individual server can relay to prevent swamping the corporate MTA. Postfix has a program called "anvil" that is capable of tracking stats about mail to be used for such things but it doesn't seem to be executed. I ran "inotifywait -m /usr/lib/postfix/anvil" while I started postfix and sent a number of messages through it from a remote server. inotifywait indicated anvil was never run. Anyone gotten postfix/anvil rate controls to work? main.cf smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no append_dot_mydomain = no readme_directory = no myhostname = site-server-q9 alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost relayhost = Out outgoing mail relay mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 10.0.0.0/8 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = 10.X.X.X smtpd_client_message_rate_limit = 1 anvil_rate_time_unit = 1h master.cf extract anvil unix - - - - 1 anvil smtp inet n - - - - smtpd

    Read the article

  • linux: mount old ATA disk to USB adapter

    - by 130490868091234
    I am trying to recover data from an old Linux that was installed in a computer on an ATA hard drive. I found a ScanLogic Corp. SL11R-IDE IDE Bridge (04ce:0002), an ATA adapter to USB 1.0 like the one in the picture: and after switching it on, I plugged it into a laptop with Ubuntu 12.04. I am used to the drives being automatically mounted, but this one doesn't show up in /media. After doing a dmesg, all I got is this: [215298.671924] usb 2-1.1: new full-speed USB device number 5 using ehci_hcd [215298.767330] scsi19 : usb-storage 2-1.1:1.0 [215299.841701] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.017258] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.197050] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.372730] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd I tried plugging in the adapter to the three different USB ports in my laptop (one of them USB 3.0), but got no luck with any of them. I get different devices under, for example: /dev/bus/usb/003/002 or /dev/bus/usb/002/004, but I don't get any /dev/sdbN links. The output blkid -o list -c /dev/null is just the laptop's partitions. I have tried taking out the jumper, putting it as master and as CS Enabled, but didn't change the result. Any ideas?

    Read the article

  • Postfix enable SSL 465 failed

    - by user221290
    I have installed the Postfix and enabled SSL/TLS, just tested, I can sent email from port 25, 578, but cannot sent email from port 465, the log is: May 26 17:24:06 mail postfix/smtpd[28721]: SSL_accept:SSLv3 write server hello A May 26 17:24:06 mail postfix/smtpd[28721]: SSL_accept:SSLv3 write certificate A May 26 17:24:06 mail postfix/smtpd[28721]: SSL_accept:SSLv3 write server done A May 26 17:24:06 mail postfix/smtpd[28721]: SSL_accept:SSLv3 flush data May 26 17:24:06 mail postfix/smtpd[28721]: SSL3 alert read:fatal:certificate unknown May 26 17:24:06 mail postfix/smtpd[28721]: SSL_accept:failed in SSLv3 read client certificate A May 26 17:24:06 mail postfix/smtpd[28721]: SSL_accept error from unknown[10.155.36.240]: 0 May 26 17:24:06 mail postfix/smtpd[28721]: warning: TLS library problem: 28721:error:14094416:SSL routines:SSL3_READ_BYTES:sslv3 alert certificate unknown:s3_pkt.c:1197:SSL alert number 46: May 26 17:24:06 mail postfix/smtpd[28721]: lost connection after CONNECT from unknown[10.155.36.240] May 26 17:24:06 mail postfix/smtpd[28721]: disconnect from unknown[10.155.36.240] My email server is: 10.155.34.117, and email client is: 10.155.36.240, the client error is: Could not connect to SMTP host: 10.155.34.117, port: 465. My Master.cf: smtps inet n - n - - smtpd -o smtpd_tls_wrappermode=yes My main.cf: smtpd_use_tls = yes smtpd_tls_auth_only = no smtpd_tls_key_file = /etc/pki/myca/mail.key smtpd_tls_cert_file = /etc/pki/myca/mail.crt smtpd_tls_CAfile = /etc/pki/myca/cacert_new.pem smtpd_tls_loglevel = 2 smtpd_tls_received_header = yes smtpd_tls_session_cache_timeout = 3600s smtpd_tls_session_cache_database = btree:/etc/postfix/smtpd_scache Seems it's my certificate issue, but I have tried to grant the file many times...I have no idea on this, please help!

    Read the article

  • Cloning a NAS drive which hosts a SQL Server DB

    - by Adrian Hand
    We have a system in the field running a server application which is suffering with major performance issues. The system in question has 2 onboard 300gb sas drives in RAID 5 from which it boots Windows Server 2003, and a 6tb buffalo terastation NAS unit (also RAID 5) to which the server app does all of its reading and writing. I believe the terastation is the source of all our woes. Whilst under load, reads and writes tick by at something of the order of 1meg/sec, though the network in question is hardly utilised. The terastation contains various data, but crucially hosts a full instance worth of SQL Server .mdf and .ldf files (master etc - the whole shooting match) I wish to stop all the services on the server, then take everything on the terastation and essentially clone it to some alternative onboard storage, so as to eliminate the terastation from the equation as far as poor performance is concerned. ie the terastation is currently drive D: - I want to copy everything off and then have the duplicate assume the drive letter so that as far as the software is aware, nothing is different. This is tricky because of the mdf and ldf files - everything else will work with a straight up file copy. Can anyone suggest a means to achieve what I am describing? Many thanks!

    Read the article

  • Best all in one linux based proxy,firewall, dhcp and wins server.

    - by BeStRaFe
    I help to run a lan in Sydney. We have a need for a proxy/gateway solution to allow those pesky games that require internet to work. I have been doing this with an ISA server and it has worked quite well. However now i wish to port this over to run on the same hardware as our cacti / nagios box under a vmware VM. ISA server is horridly nad due to the massive ram and i/o requirement for something is basically port blocking and handing out IP's. The needs are as follows. 1. DHCP 2. WINS (otherwise network devices fight over who is the WINS master) 3. Filtering based in PORT for outbound traffic. 4. Ability to whitelist IP/MAC's for internet access. 5. Web Interface. I had been thinking to use PFSENSE however there is no option for a WINS server and i cbf working my way around bsd.

    Read the article

  • BIND zones and named files

    - by preethika
    I've installed BIND in my Windows server2003. i've configured the named file in C:\named\etc\named.conf as: options { directory "c:\named\zones"; allow-transfer { none; }; recursion no; }; zone "tisdns.com" IN { type master; file "db.tisdns.com.txt"; allow-transfer { none; }; }; My zone file is configured in C:\named\zones\db.tisdns.com.txt as: $TTL 6h @ IN SOA ns1.tisdns.com. hostmaster.tisdns.co… ( 2010010901 10800 3600 604800 86400 ) @ NS ns1.tisdns.com. ns1 IN A 192.168.0.17 mug IN A 192.168.0.103 key "rndc-key" { algorithm hmac-md5; secret "M0oW24WFQZhMu9wTq8qepw=="; }; controls { inet 127.0.0.1 port 53 allow { 127.0.0.1; } keys { "rndc-key"; }; }; In the above i've given the name to the domain as "tisdns". i want to create a new domain name in a different zone file. how can i create it?

    Read the article

  • LG LW20 Express won't boot after hdd replace

    - by Mika
    My old laptop (LG LW20 Express) got a hdd failure and I replaced the hdd. Now the laptop won't boot from cd or usb. I'm trying to install ubuntu on it. When I turn the laptop on it shows me the startup screen but when it should be the time to load operating system it just gives a black screen and starts over. This loop continues until I shut down the laptop. I created the usb boot drive following this guide https://help.ubuntu.com/community/Installation/FromUSBStick/ I used my boot cd to install ubuntu on this machine I'm using right now. So at least the cd should work. From the BIOS I can see that my newly installed hdd is recognized and put as a secondary master. Also the cd and removable media are in the boot list before hdd. The laptop runs pretty hot. The fan is at full speed pretty soon after the laptop is turned on. Earlier I suspected that it would have been the almost broken hdd that would have produced that heat but there obviously is something else also. Any ideas what to check?

    Read the article

  • No video signal at boot with custom built computer

    - by Bart Pelle
    After booting my custom built computer, neither the VGA nor the HDMI methods from the video card seem to emit any signal to the display. I have tested both a regular VGA screen and a modern HDMI screen. Both did not receive signal. Below are the specifications from my computer build: Intel Core i5 3350P ASRock B75 Pro 3-M Seagate Barracuda 7200.14 ST1000 DM003 1000GB Corsair Vengeance LP CML 8GX 3M2 A1600 CGB Blue (2 cards) Cooler Master B Series B600 Club 3D Radeon HD7870 XT Jokercard Samsung SH-224 BB Black Sharkoon T28 Case The motherboard does not emit any beeps on startup. The CD tray opens properly and all fans spin. All cables are properly connected. All components are new and no damage was found on any of the components. The fans on the GPU spin aswell. The VGA test we did was by using the onboard graphics from the Intel i5, but this gave no result. The HDMI test was from the GPU which did not emit any signal either. We have not been able to test out the DVI, could this be important to test, even though all the other methods did not work? Thank you for your time and hopefully reply.

    Read the article

  • Keepalived for more than 20 virtual addresses

    - by cvaldemar
    I have set up keepalived on two Debian machines for high availability, but I've run into the maximum number of virtual IP's I can assign to my vrrp_instance. How would I go about configuring and failing over 20+ virtual IP's? This is the, very simple, setup: LB01: 10.200.85.1 LB02: 10.200.85.2 Virtual IPs: 10.200.85.100 - 10.200.85.200 Each machine is also running Apache (later Nginx) binding on the virtual IPs for SSL client certificate termination and proxying to backend webservers. The reason I need so many VIP's is the inability to use VirtualHost on HTTPS. This is my keepalived.conf: vrrp_script chk_apache2 { script "killall -0 apache2" interval 2 weight 2 } vrrp_instance VI_1 { interface eth0 state MASTER virtual_router_id 51 priority 101 virtual_ipaddress { 10.200.85.100 . . all the way to . 10.200.85.200 } An identical configuration is on the BACKUP machine, and it's working fine, but only up to the 20th IP. I have found a HOWTO discussing this problem. Basically, they suggest having just one VIP and routing all traffic "via" this one IP, and "all will be well". Is this a good approach? I'm running pfSense firewalls in front of the machines. Quote from the above link: ip route add $VNET/N via $VIP or route add $VNET netmask w.x.y.z gw $VIP Thanks in advance. EDIT: @David Schwartz said it would make sense to add a route, so I tried adding a static route to the pfSense firewall, but that didn't work as I expected it would. pfSense route: Interface: LAN Destination network: 10.200.85.200/32 (virtual IP) Gateway: 10.200.85.100 (floating virtual IP) Description: Route to VIP .100 I also made sure I had packet forwarding enabled on my hosts: $ cat /etc/sysctl.conf net.ipv4.ip_forward=1 net.ipv4.ip_nonlocal_bind=1 Am I doing this wrong? I also removed all VIPs from the keepalived.conf so it only fails over 10.200.85.100.

    Read the article

  • Windows Network File Transfer to Samba server: “Are you sure you want to copy this file without its properties?”

    - by jimp
    I am transferring a lot of files to a new NAS based on OpenMediaVault, with the Samba 3.5.6 service running. I am transferring from Windows 7 64-bit to the NAS, and on some media files Windows is prompting about losing some property data across the transfer. I have never seen this before when transferring to Samba boxes I have built myself (vs this turnkey solution), so I'm guessing there must be a Samba setting I can change to preserve the file properties in question instead of permanently losing whatever they contain (Date Taken? Exposure? Flash Fired? etc). Or maybe I've just never encountered this before; I'm really not sure. I tried adding ea support = yes and store dos attributes = yes to the [global] section, but the problem remains. The Linux file system is ext4 mounted with user_xattr (full options: defaults,acl,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0) as Samba requires. Any ideas would be greatly appreciated. Thank you! Samba config: [global] workgroup = WORKGROUP server string = %h server include = /etc/samba/dhcp.conf dns proxy = no log level = 2 syslog = 2 log file = /var/log/samba/log.%m max log size = 1000 syslog only = yes panic action = /usr/share/samba/panic-action %d encrypt passwords = true passdb backend = tdbsam obey pam restrictions = yes unix password sync = no passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . pam password change = yes socket options = TCP_NODELAY IPTOS_LOWDELAY guest account = nobody load printers = no disable spoolss = yes printing = bsd printcap name = /dev/null unix extensions = yes wide links = no create mask = 0777 directory mask = 0777 use sendfile = no null passwords = no local master = yes time server = yes wins support = yes ea support = yes store dos attributes = yes Note: I found this related question, but it explains the loss due to the user trying to transfer from NTFS to FAT32.

    Read the article

< Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >