Search Results

Search found 15386 results on 616 pages for 'usb port'.

Page 157/616 | < Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >

• Connecting Galaxy Note: Unable to mount Android Error initializing camera: -53: Could not claim the USB device

  - by Claudiu

  I'm running cm9 ics on my Galaxy Note and i tried anything i could find googleing around but to no result, if i look on the phone in usb settings there is the option for mass storage but it's grey and therefore not selectable I don`t know what the problem is but i saw somwhere that it might be an old version of libmtp so i tried to install libmtp 1.1.3 with ./configure make make install but even after when i try mtp-detect it gives me libmtp 1.1.1 is it normal? anyway when i run mtp-detect here is what it gives me libmtp version: 1.1.1 Listing raw device(s) Device 0 (VID=04e8 and PID=6860) is a Samsung GT-P7310/P7510/N7000/I9100/Galaxy Tab 7.7/10.1/S2/Nexus/Note. Found 1 device(s): Samsung: GT-P7310/P7510/N7000/I9100/Galaxy Tab 7.7/10.1/S2/Nexus/Note (04e8:6860) @ bus 2, dev 6 Attempting to connect device(s) ignoring usb_claim_interface = -99PTP_ERROR_IO: failed to open session, trying again after resetting USB interface LIBMTP libusb: Attempt to reset device ignoring usb_claim_interface = -99LIBMTP PANIC: failed to open session on second attempt Unable to open raw device 0 OK. Thanks in advamce

  Read the article

• How to Get the Folder Name of USB Disk?

  - by Kate Moss' Open Space

  When an USB Disk plugs into CE/Mobile based device, how do you know the folder name of the mounting point? Usually, it should be "USB Disk" but it is really depends on how OS image builder; they may change the folder name for whatever reason. FindFirstFlashCard looks simple and promising, the drawback is it only available on Windows Mobile. In fact, these find flash card API set will enumerate all of the mountable file system which includes SD card, CF and etc that we don't expect to get. So I am going to introduce you another way via Storage Manager. Here is the steps.

  Read the article

• squid bypass for a domain

  - by krisdigitx

  i am using squid with adzap, it possible that squid/adzap does not cache for a particluar domain eg. cnn.com this is my squid.conf file # # Recommended minimum configuration: # acl manager proto cache_object acl localhost src 127.0.0.1/32 #acl localhost src ::1/128 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 #acl to_localhost dst ::1/128 # Example rule allowing access from your local networks. # Adapt to list your (internal) IP networks from where browsing # should be allowed acl localnet src 192.168.1.0/24 acl localnet src 192.168.2.0/24 acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl CONNECT method CONNECT # # Recommended minimum Access Permission configuration: # # Only allow cachemgr access from localhost http_access allow manager localhost http_access deny manager # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # We strongly recommend the following be uncommented to protect innocent # web applications running on the proxy server who think the only # one who can access services on "localhost" is a local user #http_access deny to_localhost # # INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS # # Example rule allowing access from your local networks. # Adapt localnet in the ACL section to list your (internal) IP networks # from where browsing should be allowed http_access allow localnet http_access allow localhost # And finally deny all other access to this proxy http_access deny all # Squid normally listens to port 3128 http_port xxx.xxx.xxx.yyy:3128 transparent visible_hostname proxyserver.local # We recommend you to use at least the following line. hierarchy_stoplist cgi-bin ? # Uncomment and adjust the following to add a disk cache directory. cache_dir ufs /var/spool/squid 1024 16 256 # Leave coredumps in the first cache dir coredump_dir /var/spool/squid # Add any of your own refresh_pattern entries above these. refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . 0 20% 4320 access_log /var/log/squid/squid.log squid access_log syslog squid redirect_program /usr/local/adzap/scripts/wrapzap fixed using acl allow_domains dstdomain www.cnn.com always_direct allow allow_domains

  Read the article

• Cant get squid proxy to work

  - by danielgratz

  i need squid proxy on my centos server. But i just can't get it to work. I did yum install squid. Here is my squid.conf file (i removed all comments): acl all src 0.0.0.0/0.0.0.0 acl manager proto cache_object acl localhost src 127.0.0.1/255.255.255.255 acl to_localhost dst 127.0.0.0/8 acl SSL_ports port 443 acl Safe_ports port 80 acl Safe_ports port 21 acl Safe_ports port 443 acl Safe_ports port 70 acl Safe_ports port 210 acl Safe_ports port 1025-65535 acl Safe_ports port 280 acl Safe_ports port 488 acl Safe_ports port 591 acl Safe_ports port 777 acl CONNECT method CONNECT acl our_networks src 192.168.1.0/24 192.168.2.0/24 http_access allow our_networks http_access allow manager localhost http_access deny manager http_access deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow localhost http_access deny all icp_access allow all http_port 3128 hierarchy_stoplist cgi-bin ? access_log /var/log/squid/access.log squid acl QUERY urlpath_regex cgi-bin \? cache deny QUERY refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern . 0 20% 4320 acl apache rep_header Server ^Apache broken_vary_encoding allow apache coredump_dir /var/spool/squid Then i just put my server's public ip and port 3128 into my web browsers proxy settings... but it isn't working i can't visit any website. Please help. Thanks.

  Read the article

• Intel présente une technologie qui pourrait bien mettre l'USB 3.0 au placard : Thunderbolt permettra des transferts jusqu'à 100 GB/s

  Intel présente une technologie qui pourrait bien mettre l'USB 3.0 au placard : Thunderbolt permettra des transferts jusqu'à 100 GB/s Mise à jour du 25.02.2011 par Katleen Intel vient d'annoncer Thunderbolt : une nouvelle technologie pour relier les machines et les périphériques, qui était en cours de développement depuis des années. En 2009, elle avait déjà été annoncée sous le nom de Light Peak. La système est sensé permettre des transferts à des taux deux fois plus rapides que l'USB 3.0 (soit à 10 Gb/s). Si ces chiffres vous paraissent bons, sachez qu'ils sont largement en dessous du maximum théorique que peut fournire cette technologie, puisque Intel utilisera au départ des fils de...

  Read the article

• In 12.04, with my Linksys WUSB54G USB adapter I can see the networks, but cannot connect to any of them

  - by tobye

  I recently loaded Ubuntu version 12.04 onto my computer, and I have a WUSB54G v4 USB wireless adapter. I first tried to get it to work by simply plugging my adapter into an open USB port. This seemed to work fine, it came up with a list of wireless adapters, so I clicked on the correct one and entered the security code. It looked like it was going to connect. It tried for about five minutes before I stopped it. I then decided to create a network as I also have one setup. I did this and it connected, only one problem, I couldn't get onto the internet. Please help me, I am new to Ubuntu and am totally lost.

  Read the article

• Full USB install not booting, but Zorin full install will? [on hold]

  - by elmalote

  Okay I'm puzzled and been trying to solve this for days. I'm almost giving up on having Ubuntu. I've used Zorin will no problems, full install on USB. Boots up fine no issues. But I'm trying to install Ubuntu on the same USB stick. Exact same options under the installer. Mount point, bootloader location etc. However it will not boot with Ubuntu full install. I've tried disabling UEFI boot in BIOS, changed boot priorities and so on. I know the stick boots as Zorin has no issues. I didn't even disable UEFI boot in BIOS and Zorin boots up fine. Can someone help!? Thanks a lot.

  Read the article

• How to get my windows docs ; pics, mp3, and docs off an external usb hard drive (sata 3.5 enclosure)

  - by Alan

  Back when I had windows 7, I cloned my internal hard drive to an enclosed external usb hard drive. I then formatted my internal hard drive and installed ubuntu 11.10 as my only OS. How do I migrate my files, pics, mp3's, and etc off the external drive and back to my internal drive which now only has ubuntu on it. (and why is this process not made easier?) I have tried logging in as the root user but I cannot find the external device. I have downloaded several different apps to manage files, usb sticks and etc. PLEASE HELP!!!

  Read the article

• Wireless card power management

  - by penner

  I have noticed that when my computer in plugged in, the wireless strength increases. I'm assuming this is to do with power management. Is there a way to disable Wireless Power Management? I have found a few blog posts that show hacks to disable this but what is best practice here? Should there not be an option via the power menu that lets you toggle this? EDIT -- FILES AND LOGS AS REQUESTED /var/log/kern.log Jul 11 11:45:27 CoolBreeze kernel: [ 6.528052] postgres (1308): /proc/1308/oom_adj is deprecated, please use /proc/1308/oom_score_adj instead. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532080] [fglrx] Gart USWC size:1280 M. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532084] [fglrx] Gart cacheable size:508 M. Jul 11 11:45:27 CoolBreeze kernel: [ 6.532091] [fglrx] Reserved FB block: Shared offset:0, size:1000000 Jul 11 11:45:27 CoolBreeze kernel: [ 6.532094] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 Jul 11 11:45:27 CoolBreeze kernel: [ 6.532098] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 Jul 11 11:45:38 CoolBreeze kernel: [ 17.423743] eth1: no IPv6 routers present Jul 11 11:46:37 CoolBreeze kernel: [ 75.836426] warning: `proftpd' uses 32-bit capabilities (legacy support in use) Jul 11 11:46:37 CoolBreeze kernel: [ 75.884215] init: plymouth-stop pre-start process (2922) terminated with status 1 Jul 11 11:54:25 CoolBreeze kernel: [ 543.679614] eth1: no IPv6 routers present dmesg [ 1.411959] ACPI: Power Button [PWRB] [ 1.412046] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 1.412054] ACPI: Sleep Button [SLPB] [ 1.412150] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2 [ 1.412765] ACPI: Lid Switch [LID0] [ 1.412866] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 1.412874] ACPI: Power Button [PWRF] [ 1.412996] ACPI: Fan [FAN0] (off) [ 1.413068] ACPI: Fan [FAN1] (off) [ 1.419493] thermal LNXTHERM:00: registered as thermal_zone0 [ 1.419498] ACPI: Thermal Zone [TZ00] (27 C) [ 1.421913] thermal LNXTHERM:01: registered as thermal_zone1 [ 1.421918] ACPI: Thermal Zone [TZ01] (61 C) [ 1.421971] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.421986] ACPI: Battery Slot [BAT0] (battery present) [ 1.422062] ERST: Table is not found! [ 1.422067] GHES: HEST is not enabled! [ 1.422158] isapnp: Scanning for PnP cards... [ 1.422242] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 1.434620] ACPI: Battery Slot [BAT0] (battery present) [ 1.736355] Freeing initrd memory: 14352k freed [ 1.777846] isapnp: No Plug & Play device found [ 1.963650] Linux agpgart interface v0.103 [ 1.967148] brd: module loaded [ 1.968866] loop: module loaded [ 1.969134] ahci 0000:00:1f.2: version 3.0 [ 1.969154] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.969226] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X [ 1.969277] ahci: SSS flag set, parallel bus scan disabled [ 1.969320] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x23 impl SATA mode [ 1.969329] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems sxs apst [ 1.969338] ahci 0000:00:1f.2: setting latency timer to 64 [ 1.983340] scsi0 : ahci [ 1.983515] scsi1 : ahci [ 1.983670] scsi2 : ahci [ 1.983829] scsi3 : ahci [ 1.983985] scsi4 : ahci [ 1.984145] scsi5 : ahci [ 1.984270] ata1: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005100 irq 45 [ 1.984277] ata2: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005180 irq 45 [ 1.984282] ata3: DUMMY [ 1.984285] ata4: DUMMY [ 1.984288] ata5: DUMMY [ 1.984292] ata6: SATA max UDMA/133 abar m2048@0xf1005000 port 0xf1005380 irq 45 [ 1.985150] Fixed MDIO Bus: probed [ 1.985192] tun: Universal TUN/TAP device driver, 1.6 [ 1.985196] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 1.985285] PPP generic driver version 2.4.2 [ 1.985472] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.985507] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.985534] ehci_hcd 0000:00:1a.0: setting latency timer to 64 [ 1.985541] ehci_hcd 0000:00:1a.0: EHCI Host Controller [ 1.985626] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 1.985666] ehci_hcd 0000:00:1a.0: debug port 2 [ 1.989663] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported [ 1.989690] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xf1005800 [ 2.002183] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 2.002447] hub 1-0:1.0: USB hub found [ 2.002455] hub 1-0:1.0: 3 ports detected [ 2.002607] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 2.002633] ehci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.002639] ehci_hcd 0000:00:1d.0: EHCI Host Controller [ 2.002737] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.002775] ehci_hcd 0000:00:1d.0: debug port 2 [ 2.006780] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported [ 2.006806] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf1005c00 [ 2.022161] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 2.022401] hub 2-0:1.0: USB hub found [ 2.022409] hub 2-0:1.0: 3 ports detected [ 2.022567] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.022599] uhci_hcd: USB Universal Host Controller Interface driver [ 2.022720] usbcore: registered new interface driver libusual [ 2.022813] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 2.035831] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.035844] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.036096] mousedev: PS/2 mouse device common for all mice [ 2.036710] rtc_cmos 00:07: RTC can wake from S4 [ 2.036881] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0 [ 2.037143] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 2.037503] device-mapper: uevent: version 1.0.3 [ 2.037656] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.037725] EISA: Probing bus 0 at eisa.0 [ 2.037729] EISA: Cannot allocate resource for mainboard [ 2.037734] Cannot allocate resource for EISA slot 1 [ 2.037738] Cannot allocate resource for EISA slot 2 [ 2.037741] Cannot allocate resource for EISA slot 3 [ 2.037745] Cannot allocate resource for EISA slot 4 [ 2.037749] Cannot allocate resource for EISA slot 5 [ 2.037753] Cannot allocate resource for EISA slot 6 [ 2.037756] Cannot allocate resource for EISA slot 7 [ 2.037760] Cannot allocate resource for EISA slot 8 [ 2.037764] EISA: Detected 0 cards. [ 2.037782] cpufreq-nforce2: No nForce2 chipset. [ 2.038264] cpuidle: using governor ladder [ 2.039015] cpuidle: using governor menu [ 2.039019] EFI Variables Facility v0.08 2004-May-17 [ 2.040061] TCP cubic registered [ 2.041438] NET: Registered protocol family 10 [ 2.043814] NET: Registered protocol family 17 [ 2.043823] Registering the dns_resolver key type [ 2.044290] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 2.044336] Using IPI No-Shortcut mode [ 2.045620] PM: Hibernation image not present or could not be loaded. [ 2.045644] registered taskstats version 1 [ 2.073070] Magic number: 4:976:796 [ 2.073415] rtc_cmos 00:07: setting system clock to 2012-07-11 18:45:23 UTC (1342032323) [ 2.076654] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.076658] EDD information not available. [ 2.302111] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.302587] ata1.00: ATA-9: M4-CT128M4SSD2, 000F, max UDMA/100 [ 2.302595] ata1.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 2.303143] ata1.00: configured for UDMA/100 [ 2.303453] scsi 0:0:0:0: Direct-Access ATA M4-CT128M4SSD2 000F PQ: 0 ANSI: 5 [ 2.303746] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.303920] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB) [ 2.304213] sd 0:0:0:0: [sda] Write Protect is off [ 2.304225] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.304471] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.306818] sda: sda1 sda2 < sda5 > [ 2.308780] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.318162] Refined TSC clocksource calibration: 1595.999 MHz. [ 2.318169] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 2.318178] Switching to clocksource tsc [ 2.450939] hub 1-1:1.0: USB hub found [ 2.451121] hub 1-1:1.0: 6 ports detected [ 2.561786] usb 2-1: new high-speed USB device number 2 using ehci_hcd [ 2.621757] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.636143] ata2.00: ATAPI: TSSTcorp DVD+/-RW TS-T633C, D800, max UDMA/100 [ 2.636152] ata2.00: applying bridge limits [ 2.649711] ata2.00: configured for UDMA/100 [ 2.653762] scsi 1:0:0:0: CD-ROM TSSTcorp DVD+-RW TS-T633C D800 PQ: 0 ANSI: 5 [ 2.661486] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.661494] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.661890] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.662156] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 2.694649] hub 2-1:1.0: USB hub found [ 2.694840] hub 2-1:1.0: 8 ports detected [ 2.765823] usb 1-1.4: new high-speed USB device number 3 using ehci_hcd [ 2.981454] ata6: SATA link down (SStatus 0 SControl 300) [ 2.982597] Freeing unused kernel memory: 740k freed [ 2.983523] Write protecting the kernel text: 5816k [ 2.983808] Write protecting the kernel read-only data: 2376k [ 2.983811] NX-protecting the kernel data: 4424k [ 3.014594] udevd[127]: starting version 175 [ 3.068925] sdhci: Secure Digital Host Controller Interface driver [ 3.068932] sdhci: Copyright(c) Pierre Ossman [ 3.069714] sdhci-pci 0000:09:00.0: SDHCI controller found [1180:e822] (rev 1) [ 3.069742] sdhci-pci 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.069786] sdhci-pci 0000:09:00.0: Will use DMA mode even though HW doesn't fully claim to support it. [ 3.069798] sdhci-pci 0000:09:00.0: setting latency timer to 64 [ 3.069816] mmc0: no vmmc regulator found [ 3.069877] Registered led device: mmc0:: [ 3.070946] mmc0: SDHCI controller on PCI [0000:09:00.0] using DMA [ 3.071078] tg3.c:v3.121 (November 2, 2011) [ 3.071252] tg3 0000:0b:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.071269] tg3 0000:0b:00.0: setting latency timer to 64 [ 3.071403] firewire_ohci 0000:09:00.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 3.071417] firewire_ohci 0000:09:00.3: setting latency timer to 64 [ 3.078509] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 3.078517] EXT4-fs (sda1): write access will be enabled during recovery [ 3.110417] tg3 0000:0b:00.0: eth0: Tigon3 [partno(BCM95784M) rev 5784100] (PCI Express) MAC address b8:ac:6f:71:02:a6 [ 3.110425] tg3 0000:0b:00.0: eth0: attached PHY is 5784 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0]) [ 3.110431] tg3 0000:0b:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.110436] tg3 0000:0b:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit] [ 3.125492] firewire_ohci: Added fw-ohci device 0000:09:00.3, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x11 [ 3.390124] EXT4-fs (sda1): orphan cleanup on readonly fs [ 3.390135] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078710 [ 3.390232] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2363071 [ 3.390327] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078711 [ 3.390350] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078709 [ 3.390367] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078708 [ 3.390384] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078707 [ 3.390401] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078706 [ 3.390417] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078705 [ 3.390435] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078551 [ 3.390452] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078523 [ 3.390470] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7078520 [ 3.390487] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 7077901 [ 3.390551] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063272 [ 3.390562] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063266 [ 3.390572] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063261 [ 3.390582] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063256 [ 3.390592] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4063255 [ 3.390602] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2363072 [ 3.390620] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2360050 [ 3.390698] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 5250064 [ 3.390710] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2365394 [ 3.390728] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 2365390 [ 3.390745] EXT4-fs (sda1): 22 orphan inodes deleted [ 3.390748] EXT4-fs (sda1): recovery complete [ 3.397636] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 3.624910] firewire_core: created device fw0: GUID 464fc000110e2661, S400 [ 3.927467] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 3.929965] udevd[400]: starting version 175 [ 3.933581] Adding 6278140k swap on /dev/sda5. Priority:-1 extents:1 across:6278140k SS [ 3.945183] lp: driver loaded but no devices found [ 3.999389] wmi: Mapper loaded [ 4.016696] ite_cir: Auto-detected model: ITE8708 CIR transceiver [ 4.016702] ite_cir: Using model: ITE8708 CIR transceiver [ 4.016706] ite_cir: TX-capable: 1 [ 4.016710] ite_cir: Sample period (ns): 8680 [ 4.016713] ite_cir: TX carrier frequency (Hz): 38000 [ 4.016716] ite_cir: TX duty cycle (%): 33 [ 4.016719] ite_cir: RX low carrier frequency (Hz): 0 [ 4.016722] ite_cir: RX high carrier frequency (Hz): 0 [ 4.025684] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 4.025691] Disabling lock debugging due to kernel taint [ 4.027410] IR NEC protocol handler initialized [ 4.030250] lib80211: common routines for IEEE802.11 drivers [ 4.030257] lib80211_crypt: registered algorithm 'NULL' [ 4.036024] IR RC5(x) protocol handler initialized [ 4.036092] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 4.036188] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X [ 4.036307] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 4.036361] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 4.039006] acpi device:03: registered as cooling_device10 [ 4.039164] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input5 [ 4.039261] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 4.049753] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 4.050201] wl 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 4.050215] wl 0000:05:00.0: setting latency timer to 64 [ 4.052252] Registered IR keymap rc-rc6-mce [ 4.052432] input: ITE8708 CIR transceiver as /devices/virtual/rc/rc0/input6 [ 4.054614] IR RC6 protocol handler initialized [ 4.054787] rc0: ITE8708 CIR transceiver as /devices/virtual/rc/rc0 [ 4.054839] ite_cir: driver has been successfully loaded [ 4.057338] IR JVC protocol handler initialized [ 4.061553] IR Sony protocol handler initialized [ 4.066578] input: MCE IR Keyboard/Mouse (ite-cir) as /devices/virtual/input/input7 [ 4.066724] IR MCE Keyboard/mouse protocol handler initialized [ 4.072580] lirc_dev: IR Remote Control driver registered, major 250 [ 4.073280] rc rc0: lirc_dev: driver ir-lirc-codec (ite-cir) registered at minor = 0 [ 4.073286] IR LIRC bridge handler initialized [ 4.077849] Linux video capture interface: v2.00 [ 4.079402] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:640f) [ 4.085492] EDAC MC: Ver: 2.1.0 [ 4.087138] lib80211_crypt: registered algorithm 'TKIP' [ 4.091027] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 4.091733] snd_hda_intel 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 4.091826] snd_hda_intel 0000:02:00.1: irq 47 for MSI/MSI-X [ 4.091861] snd_hda_intel 0000:02:00.1: setting latency timer to 64 [ 4.093115] EDAC i7core: Device not found: dev 00.0 PCI ID 8086:2c50 [ 4.112448] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 4.112612] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/0000:02:00.1/sound/card1/input9 [ 4.113311] type=1400 audit(1342032325.540:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=658 comm="apparmor_parser" [ 4.114501] type=1400 audit(1342032325.540:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=658 comm="apparmor_parser" [ 4.115253] type=1400 audit(1342032325.540:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=658 comm="apparmor_parser" [ 4.121870] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input10 [ 4.122096] usbcore: registered new interface driver uvcvideo [ 4.122100] USB Video Class driver (1.1.1) [ 4.128729] [fglrx] Maximum main memory to use for locked dma buffers: 5840 MBytes. [ 4.129678] [fglrx] vendor: 1002 device: 68c0 count: 1 [ 4.131991] [fglrx] ioport: bar 4, base 0x2000, size: 0x100 [ 4.132015] pci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.132024] pci 0000:02:00.0: setting latency timer to 64 [ 4.133712] [fglrx] Kernel PAT support is enabled [ 4.133747] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 4.162666] eth1: Broadcom BCM4727 802.11 Hybrid Wireless Controller 5.100.82.38 [ 4.184133] device-mapper: multipath: version 1.3.0 loaded [ 4.196660] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 4.279897] input: Dell WMI hotkeys as /devices/virtual/input/input11 [ 4.292402] Bluetooth: Core ver 2.16 [ 4.292449] NET: Registered protocol family 31 [ 4.292454] Bluetooth: HCI device and connection manager initialized [ 4.292459] Bluetooth: HCI socket layer initialized [ 4.292463] Bluetooth: L2CAP socket layer initialized [ 4.292473] Bluetooth: SCO socket layer initialized [ 4.296333] Bluetooth: RFCOMM TTY layer initialized [ 4.296342] Bluetooth: RFCOMM socket layer initialized [ 4.296345] Bluetooth: RFCOMM ver 1.11 [ 4.313586] ppdev: user-space parallel port driver [ 4.316619] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 4.316625] Bluetooth: BNEP filters: protocol multicast [ 4.383980] type=1400 audit(1342032325.812:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=938 comm="apparmor_parser" [ 4.385173] type=1400 audit(1342032325.812:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=938 comm="apparmor_parser" [ 4.425757] init: failsafe main process (898) killed by TERM signal [ 4.477052] type=1400 audit(1342032325.904:7): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1011 comm="apparmor_parser" [ 4.477592] type=1400 audit(1342032325.904:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1010 comm="apparmor_parser" [ 4.478099] type=1400 audit(1342032325.904:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=1017 comm="apparmor_parser" [ 4.479233] type=1400 audit(1342032325.904:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1014 comm="apparmor_parser" [ 4.510060] vesafb: mode is 1152x864x32, linelength=4608, pages=0 [ 4.510065] vesafb: scrolling: redraw [ 4.510071] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 4.510084] mtrr: no more MTRRs available [ 4.513081] vesafb: framebuffer at 0xd0000000, mapped to 0xf9400000, using 3904k, total 3904k [ 4.515203] Console: switching to colour frame buffer device 144x54 [ 4.515278] fb0: VESA VGA frame buffer device [ 4.590743] tg3 0000:0b:00.0: irq 48 for MSI/MSI-X [ 4.702009] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.704409] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 4.978379] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 5.030104] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input12 [ 5.045782] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround [ 5.519573] [fglrx] ATIF platform detected with notification ID: 0x81 [ 6.391466] fglrx_pci 0000:02:00.0: irq 49 for MSI/MSI-X [ 6.393137] [fglrx] Firegl kernel thread PID: 1305 [ 6.393306] [fglrx] Firegl kernel thread PID: 1306 [ 6.393472] [fglrx] Firegl kernel thread PID: 1307 [ 6.393726] [fglrx] IRQ 49 Enabled [ 6.528052] postgres (1308): /proc/1308/oom_adj is deprecated, please use /proc/1308/oom_score_adj instead. [ 6.532080] [fglrx] Gart USWC size:1280 M. [ 6.532084] [fglrx] Gart cacheable size:508 M. [ 6.532091] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 6.532094] [fglrx] Reserved FB block: Unshared offset:f8fd000, size:403000 [ 6.532098] [fglrx] Reserved FB block: Unshared offset:3fff4000, size:c000 [ 17.423743] eth1: no IPv6 routers present [ 75.836426] warning: `proftpd' uses 32-bit capabilities (legacy support in use) [ 75.884215] init: plymouth-stop pre-start process (2922) terminated with status 1 [ 543.679614] eth1: no IPv6 routers present lsmod Module Size Used by kvm_intel 127560 0 kvm 359456 1 kvm_intel joydev 17393 0 vesafb 13516 1 parport_pc 32114 0 bnep 17830 2 ppdev 12849 0 rfcomm 38139 0 bluetooth 158438 10 bnep,rfcomm dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi binfmt_misc 17292 1 dell_laptop 17767 0 dcdbas 14098 1 dell_laptop dm_multipath 22710 0 fglrx 2909855 143 snd_hda_codec_hdmi 31775 1 psmouse 72919 0 serio_raw 13027 0 i7core_edac 23382 0 lib80211_crypt_tkip 17275 0 edac_core 46858 1 i7core_edac uvcvideo 67203 0 snd_hda_codec_idt 60251 1 videodev 86588 1 uvcvideo ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec ir_mce_kbd_decoder 12681 0 snd_seq_midi 13132 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 snd_rawmidi 25424 1 snd_seq_midi ir_rc6_decoder 12459 0 wl 2646601 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event ir_rc5_decoder 12459 0 video 19068 0 snd_hda_intel 32765 5 snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd_hda_codec 109562 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel rc_rc6_mce 12454 0 lib80211 14040 2 lib80211_crypt_tkip,wl snd_hwdep 13276 1 snd_hda_codec ir_nec_decoder 12459 0 snd_pcm 80845 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec ite_cir 24743 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ite_cir snd_timer 28931 2 snd_seq,snd_pcm wmi 18744 1 dell_wmi snd 62064 20 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_rawmidi,snd_seq,snd_seq_device,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer mac_hid 13077 0 soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm coretemp 13269 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141369 0 firewire_ohci 40172 0 sdhci_pci 18324 0 firewire_core 56906 1 firewire_ohci sdhci 28241 1 sdhci_pci crc_itu_t 12627 1 firewire_core lshw *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:a9:54:31 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.0.117 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0900000-f0903fff *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0b:00.0 logical name: eth0 version: 10 serial: b8:ac:6f:71:02:a6 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 firmware=sb v2.19 latency=0 link=no multicast=yes port=twisted pair resources: irq:48 memory:f0d00000-f0d0ffff

  Read the article

• DVD not detected?

  - by Benjamin

  As i insert a DVD in my drive (on a laptop) using Kubuntu 12.04, the DVD is not detected. The drive takes the DVD, I can hear it munching on it for a while, and then nothing. Even ejecting the DVD becomes a hassle, I need to do that at boot time otherwise the OS won't allow me to eject. Kubuntu 12.04 used to read and mount the same DVDs just fine a week ago. Edit: since I am able to boot from CD, can I safely assume the issue is not a hardware issue? How can I fix this? wodim --devices returns: wodim: Overview of accessible drives (1 found) : ------------------------------------------------------------------------- 0 dev='/dev/sg1' rwrw-- : 'Optiarc' 'DVD+-RW AD-7640A' ------------------------------------------------------------------------- sudo lshw -class disk returns: *-cdrom description: DVD-RAM writer product: DVD+-RW AD-7640A vendor: Optiarc physical id: 0.0.0 bus info: scsi@3:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/dvdrw2 logical name: /dev/sr0 version: JD06 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=open lspci returns: 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 0c) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (secondary) (rev 0c) 00:1a.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3) 00:1f.0 ISA bridge: Intel Corporation 82801HM (ICH8M) LPC Interface Controller (rev 03) 00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03) 06:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 08:05.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 08:05.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 02) 08:05.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) and lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0c45:63e0 Microdia Sonix Integrated Webcam Bus 003 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader The /etc/modprobe.d/blacklist.conf contains: # This file lists those modules which we don't want to be loaded by # alias expansion, usually so some other driver will be loaded for the # device instead. # evbug is a debug tool that should be loaded explicitly blacklist evbug # these drivers are very simple, the HID drivers are usually preferred blacklist usbmouse blacklist usbkbd # replaced by e100 blacklist eepro100 # replaced by tulip blacklist de4x5 # causes no end of confusion by creating unexpected network interfaces blacklist eth1394 # snd_intel8x0m can interfere with snd_intel8x0, doesn't seem to support much # hardware on its own (Ubuntu bug #2011, #6810) blacklist snd_intel8x0m # Conflicts with dvb driver (which is better for handling this device) blacklist snd_aw2 # causes failure to suspend on HP compaq nc6000 (Ubuntu: #10306) blacklist i2c_i801 # replaced by p54pci blacklist prism54 # replaced by b43 and ssb. blacklist bcm43xx # most apps now use garmin usb driver directly (Ubuntu: #114565) blacklist garmin_gps # replaced by asus-laptop (Ubuntu: #184721) blacklist asus_acpi # low-quality, just noise when being used for sound playback, causes # hangs at desktop session start (Ubuntu: #246969) blacklist snd_pcsp # ugly and loud noise, getting on everyone's nerves; this should be done by a # nice pulseaudio bing (Ubuntu: #77010) blacklist pcspkr # EDAC driver for amd76x clashes with the agp driver preventing the aperture # from being initialised (Ubuntu: #297750). Blacklist so that the driver # continues to build and is installable for the few cases where its # really needed. blacklist amd76x_edac

  Read the article

• boot issues - long delay, then "gave up waiting for root device"

  - by chazomaticus

  I've had this issue on and off for about two years now. I noticed it on a new (custom built) machine running 10.04 when that first came out, but then it went away until a few months ago. I've gone through a number of hard drive changes but I can't say specifically what if anything I changed hardware-wise to make it stop or start happening. I had assumed upgrading to a modern Ubuntu version would fix the issue, so I installed 12.04 beta on a spare partition last night, but it's still happening. Here's the issue. After grub loads and I select a kernel to boot, the screen goes blank save for a blinking cursor. It sits in this state for many long minutes before it finally gives up and gives me an initramfs shell with the message gave up waiting for root device (and lists the /dev/disk/by-uuid/... path it was waiting for) but no other specific diagnostic information. Now, here's the tricky part. For one, the problem is intermittent - sometimes it progresses from the blinking cursor to the Ubuntu splash boot screen in a few seconds, and once it gets that far it always continues booting fine. The really bizarre thing is that I can "force" it to "find" the root device by repeatedly pressing the space bar and hitting the machine's power button. If I tap those enough, eventually I will notice the hard drive light coming on, at which point it will always continue the boot process after a few seconds. Interestingly, if I wait slightly too long before pressing the power button (30s?), as soon as I press it I get the gave up waiting message and the initramfs shell. I've tried setting up /etc/fstab (and the grub menu.lst or whatever it's called nowadays) to use device names (e.g. /dev/sda1) instead of UUIDs, but I get the same effect just with the device name, not UUID, in the error message. I should also mention that when I boot to Windows 7, there is no issue. It boots slowly all the time just by virtue of being Windows, but it never hangs indefinitely. This would seem to indicate it's a problem in Ubuntu, not the hardware. It's pretty annoying to have to babysit the computer every time it boots. Any ideas? I'm at a loss. Not even sure how to diagnose the issue. Thanks! EDIT: Here's some dmesg output from 10.04. The 15 second gap is where it was doing nothing. I pressed the power button and space bar a few times, and the stuff at 16 seconds happened. Not sure what any of it means. [ 1.320250] scsi18 : ahci [ 1.320294] scsi19 : ahci [ 1.320320] ata19: SATA max UDMA/133 abar m8192@0xfd4fe000 port 0xfd4fe100 ir q 18 [ 1.320323] ata20: SATA max UDMA/133 abar m8192@0xfd4fe000 port 0xfd4fe180 ir q 18 [ 1.403886] usb 2-4: new high speed USB device using ehci_hcd and address 4 [ 1.562558] usb 2-4: configuration #1 chosen from 1 choice [ 16.477824] ata16: SATA link down (SStatus 0 SControl 300) [ 16.477843] ata19: SATA link down (SStatus 0 SControl 300) [ 16.477857] ata3: SATA link down (SStatus 0 SControl 300) [ 16.477895] ata15: SATA link down (SStatus 0 SControl 300) [ 16.477906] ata20: SATA link down (SStatus 0 SControl 300) [ 16.477977] ata17: SATA link down (SStatus 0 SControl 300) [ 16.478003] ata12: SATA link down (SStatus 0 SControl 300) [ 16.478046] ata13: SATA link down (SStatus 0 SControl 300) [ 16.478063] ata14: SATA link down (SStatus 0 SControl 300) [ 16.478108] ata11: SATA link down (SStatus 0 SControl 300) [ 16.478123] ata18: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 16.478127] ata6: SATA link down (SStatus 0 SControl 300) [ 16.478157] ata5: SATA link down (SStatus 0 SControl 300) [ 16.478193] ata18.00: ATAPI: MARVELL VIRTUALL, 1.09, max UDMA/66 After that, it took its sweet time, and I had to keep hitting space bar to coax it along. Here's some more dmesg output from a little later in the boot process: [ 17.982291] input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00 :13.0/usb5/5-2/5-2:1.0/input/input4 [ 17.982335] generic-usb 0003:046E:5506.0002: input,hidraw1: USB HID v1.10 Key board [BTC USB Multimedia Keyboard] on usb-0000:00:13.0-2/input0 [ 18.005211] input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00 :13.0/usb5/5-2/5-2:1.1/input/input5 [ 18.005274] generic-usb 0003:046E:5506.0003: input,hiddev96,hidraw2: USB HID v1.10 Device [BTC USB Multimedia Keyboard] on usb-0000:00:13.0-2/input1 [ 22.484906] EXT4-fs (sda6): INFO: recovery required on readonly filesystem [ 22.484910] EXT4-fs (sda6): write access will be enabled during recovery [ 22.548542] EXT4-fs (sda6): recovery complete [ 22.549074] EXT4-fs (sda6): mounted filesystem with ordered data mode [ 32.516772] Adding 20482832k swap on /dev/sda5. Priority:-1 extents:1 across:20482832k [ 32.742540] udev: starting version 151 [ 33.002004] Bluetooth: Atheros AR30xx firmware driver ver 1.0 [ 33.008135] parport_pc 00:09: reported by Plug and Play ACPI [ 33.008186] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 33.012076] lp: driver loaded but no devices found [ 33.037271] ppdev: user-space parallel port driver [ 33.090256] lp0: using parport0 (interrupt-driven). Any clues in there?

  Read the article

• BizTalk &ndash; Routing failure on Delivery Notifications (BizTalk 2006 R2 to 2013)

  - by S.E.R.

  Originally posted on: http://geekswithblogs.net/SERivas/archive/2013/11/11/biztalk-routing-failure-on-delivery-notifications.aspxThis is a detailed explanation of a something I posted a few month ago on stackoverflow, concerning a weird behavior (a bug, really…) of the delivery notifications in BizTalk. Reminder: what are delivery notifications Mechanism BizTalk has the ability to automatically publish positive acknowledgments (ACK) when it has succeeded transmitting a message or negative acknowledgments (NACK) in case of a transmission failure. Orchestrations can use delivery notifications to subscribe to those ACKs and NACKs in order to know if a message sent on a one-way send port has been successfully transmitted. Delivery Notifications can be “activated” in two ways: The most common and easy way is to set the Delivery Notification property of a logical send port (in the orchestration designer) to Transmitted: Another way is to set the BTS.AckRequired context property of the message to be sent to true: NOTE: fundamentally, those methods are strictly equivalent since the fact of setting the Delivery Notification to Transmitted on the send port only tells BizTalk the BTS.AckRequired context property has to be set to true on the outgoing message. Related context properties ACKs and NACKs have a common set of propoted context properties, which are : Propriété Description AckType Equals ACK when successful or NACK otherwise AckID MessageID of the message concerned by the acknowledgment AckOwnerID InstanceID of the instance associated with the acknowledgment AckSendPortID ID of the send port AckSendPortName Name of the send port AckOutboundTransportLocation URI of the send port AckReceivePortID ID of the port the message came from AckReceivePortName Name of the port the message came from AckInboundTransportLocation URI of the port the message came from Detailed behavior The way Delivery Notifications are handled by BizTalk is peculiar compared to the standard behavior of the Message Box: if no active subscription exists for the acknowledgment, it is simply discarded. The direct consequence of this is that there can be no routing failure for an acknowledgment, and an acknowledgment cannot be suspended. Moreover, when a message is sent to a send port where Delivery Notification = Transmitted, a correlation set is initialized and a correlation token is attached to the message (Context property: CorrelationToken). This correlation token will also be attached to the acknowledgment. So when the acknowledgment is issued, it is automatically routed to the source orchestration. Finally, when a NACK is received by the source orchestration, a DeliveryFailureException is thrown, which can be caught in Catch section. Context of the problem Consider this scenario: In an orchestration, Delivery Notifications are activated on a One-Way send port In case of a transmission failure, the messaging instance is suspended and the orchestration catches an exception (DeliveryFailureException). When the exception is caught, the orchestration does some logging and then terminates (thanks to a Terminate shape). So that leaves only the suspended messaging instance, waiting to be resumed. Symptoms Once the problem that caused the transmission failure is solved, the messaging instance is resumed. Considering what was said in the reminder, we would expect the instance to complete, leaving no active or suspended instance. Nevertheless, the result is that the messaging instance is once more suspended, this time because of a routing failure: The routing failure report shows that the suspended message has the following attached properties: Explanation Those properties clearly indicate that the message being suspended is an acknowledgment (ACK in this case), which was published in the message box and was supended because no subscribers were found. This makes sense, since the source orchestration was terminated before we resumed the messaging instance. So its subscription to the acknowledgments was no longer active when the ACK was published, which explains the routing failure. But this behavior is in direct contradiction with what was said earlier: an acknowledgment must be discarded when no subscriber is found and therefore should not be suspended. Cause It is indeed an outright bug, which appeared with the SP1 of BizTalk 2006 R2 and was never corrected since then: not in the next 4 CUs, not in BizTalk 2009, not in 2010 and not event in 2013 – though I haven’t tested CU1 and CU2 for this last edition, but I bet there is nothing to be expected from those CUs (on this particular point). Side effects This bug can have pretty nasty side effects: this behavior can be propagated to other ports, due to routing mechanisms. For instance: you have configured the ESB Toolkit and have activated the “Enable routing failure for failed messages”. The result will be that the ESB Exception SQL send port will also try and publish ACKs or NACKs concerning its own messaging instances. In itself, this is already messy, but remember that those acknowledgments will also have the source correlation token attached to them… See how far it goes? Well, actually there is more: in SQL send ports, transactions will be rolled back because of the routing failure (I guess it also happens with other adapters - like Oracle, but I haven’t tested them). Again, think of what happens when the send port is the ESB Exception send port: your BizTalk box is going mad, but you have no idea since no exception can be written in the exception database! All of this can be tricky to diagnose, I can tell you that… Solution There is no real solution, only a work-around, but it won’t solve all of the problems and side effects. The idea is to create an orchestration which subscribes to all acknowledgments. That is to say: The message type of the incoming message will be XmlDocument The BTS.AckType property exists The logical receive port will use direct binding By doing so, all acknowledgments will be consumed by an instance of this orchestration, thus avoiding the routing failure. Here is an example of what this orchestration could look like: In order not to pollute the HAT and the DTA Db (after all, this orchestration is only meant to be a palliative to some faulty internal BizTalk mechanism, so there should be no trace of its execution), all tracking must be deactivated:

  Read the article

• How to run VisualSVN Server on port 443 running IIS on same server?

  - by Metro Smurf

  Server 2008 R2 SP1 VisualSVN Server 2.1.6 The IIS server has about 10 sites. One of them uses https over port 443 with the following bindings: http x.x.x.39:80 site.com http x.x.x.39:80 www.site.com https x.x.x.39:443 VisualSVN Server Properties server name: svn.SomeSite.com server port: 443 Server Binding: x.x.x.40 No sites on IIS are listening to x.x.x.40. When starting up VisualSVN server, the following errors are thrown: make_sock: could not bind to address x.x.x.40:443 (OS 10013) An attempt was made to access a socket in a way forbidden by its access permissions. no listening sockets available, shutting down When I stop Site.com on IIS, then VisualSVN Server starts up without a problem. When I bind VisualSVN server to port 8443 and start Site.com, then VisualSVN Server starts without a problem. My goal is to be able to access the VisualSvn Server with a normal url, i.e., one that does't use a port number in the address: https://svn.site.com vs https://svn.site.com:8443 What needs to be configured to allow VisualSVN Server to run on port 443 with IIS running on the same server? Edit / Answer The answer provided by Ivan did point me in the right direction. For anyone else running into this, here is a bit more information. Even though my IIS had no bindings set to the IP address I am using for VisualSvn, IIS will still take the IP address hostage unless IIS is explicitly told which IP addresses to listen to. There is no GUI in Win Server 2k8 to configure the IP addresses for IIS to listen; by default, IIS listens to all IP addresses assigned to the server. The following will help configure IIS to only listen to the IP addresses you want: open a command prompt enter: netsh enter: http enter: show iplisten -- this will show a table of the IP addresses IIS is listening to. By default, the table will be empty (I guess this means IIS listens to all IP's) For each IP address IIS should listen to, enter: add iplisten ipaddress=x.x.x.x enter: show iplisten -- you should now see all the IP addresses added to the listening table. Exit and then reset IIS. Each of these commands can also be run directly, i.e., netsh http show iplisten If you need to delete an IP address from the listening table: open a command prompt enter: netsh enter: http enter: delete iplisten ipaddress=x.x.x.x Exit and then reset IIS.

  Read the article

• OSS4 on Debian Squeeze

  - by mit

  Hi, I am trying to get OSS4 to work on a Debian Squeeze 64 bit machine with an usb sound adapter. There is no sound from this adapter at the present, although it worked just before on the previous installation. You can see the output of some commands here: $ sudo /etc/init.d/oss4-base restart Stopping Open Sound System: SNDCTL_MIX_EXTINFO: No such device or address done. Starting Open Sound System: done (OSS is already loaded). $ sudo /etc/init.d/oss4-base stop Stopping Open Sound System: SNDCTL_MIX_EXTINFO: No such device or address done. $ sudo /etc/init.d/oss4-base start Starting Open Sound System: done (OSS is already loaded). $ ossinfo Version info: OSS 4.2 (b 2002/201001250441) (0x00040100) GPL Platform: Linux/x86_64 2.6.32-5-xen-amd64 #1 SMP Fri Dec 10 17:41:50 UTC 2010 (pc11) Number of audio devices: 2 Number of audio engines: 2 Number of MIDI devices: 0 Number of mixer devices: 2 Device objects 0: osscore0 OSS core services 1: oss_hdaudio0 ATI HD Audio interrupts=0 (613) HD Audio controller ATI HD Audio Vendor ID 0x10024383 Subvendor ID 0x10192816 Codec 0: Not present 2: oss_usb0 USB audio core services 3: usb0d8c0126-0 USB sound device 4: usb0d8c0126-1 USB sound device 5: usb0d8c0126-2 USB sound device 6: usb0d8c0126-3 USB sound device MIDI devices (/dev/midi*) Mixer devices 0: (USB sound device )(Mixer 0 of device object 3) 1: USB sound device (Mixer 0 of device object 5) Audio devices (USB sound device play /dev/oss/usb0d8c0126-1/pcm0 ) (device index 0) USB sound device play /dev/oss/usb0d8c0126-3/pcm0 (device index 1) Nodes /dev/dsp -> /dev/oss/usb0d8c0126-1/pcm0 /dev/dsp_out -> /dev/oss/usb0d8c0126-1/pcm0 /dev/dsp_mmap -> /dev/oss/usb0d8c0126-1/pcm0 $ osstest Sound subsystem and version: OSS 4.2 (b 2002/201001250441) (0x00040100) Platform: Linux/x86_64 2.6.32-5-xen-amd64 #1 SMP Fri Dec 10 17:41:50 UTC 2010 *** Scanning sound adapter #-1 *** /dev/oss/usb0d8c0126-1/pcm0 (audio engine 0): USB sound device play - Device not present - Skipping *** Scanning sound adapter #-1 *** /dev/oss/usb0d8c0126-3/pcm0 (audio engine 1): USB sound device play - Performing audio playback test... /dev/oss/usb0d8c0126-3/pcm0: No such file or directory Can't open the device *** Some errors were detected during the tests *** $ ossxmix /dev/oss/usb0d8c0126-2/mix0: No such file or directory No mixers could be opened $ ossmix SNDCTL_MIX_EXTINFO: No such device or address ad@pc11:~$ man ossmix ad@pc11:~$ ossmix -a SNDCTL_MIX_EXTINFO: No such device or address ad@pc11:~$ man ossmix ad@pc11:~$ ossmix -D SNDCTL_MIX_EXTINFO: No such device or address ad@pc11:~$ ossmix -D 0 SNDCTL_MIX_EXTINFO: No such device or address ad@pc11:~$ man ossmix ad@pc11:~$ ossxmix /dev/oss/usb0d8c0126-2/mix0: No such file or directory No mixers could be opened How can I make oss sound work? I can add more information if necessary.

  Read the article

• Graphics driver for ubuntu on dell latitude XT

  - by marc.riera

  Hi, we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

  Read the article

• Nexus One & Windows XP USB Driver

  - by Stefan

  I've been unable to get my Nexus One working as a development phone on Windows XP. I've got the driver (revision 3 for N1 support), I've got it installed according to the official installation guide, and the phone appears in the Device Manager just as the guide says it should. However, adb still can't find the phone. 'adb devices', for example, returns no active devices. Am I forgetting some basic step? One thing I've noticed is that the driver is labeled in Windows as version 2 released November, 2009 (I need version 3 from January 2010 for N1 support). However, I've never had version 2 installed. I've used the SDK to download version 3 several times - even deleted it and redownloaded it. I've uninstalled/reinstalled the version 3 driver multiple times. It still says version 2. Is this the problem, or this something completely unrelated? Note: The phone is working as a dev phone on Ubuntu, so I know the phone/cable/etc. are good. It's either my fault or the driver's.

  Read the article

• How to deal with job that stop and cannot continue unless made foreground?

  - by Vi

  Recent example: mountlo (using UML): vi@vi-notebook:~/b$ mountlo -m 16 -d /dev/uba1 /home/vi/mnt/usb -t vfat -o iocharset=utf8,allow_other& [1] 32561 vi@vi-notebook:~/b$ Checking that ptrace can change system call numbers...OK Checking syscall emulation patch for ptrace...OK Checking advanced syscall emulation patch for ptrace...OK Checking PROT_EXEC mmap in /tmp...OK Checking for the skas3 patch in the host: - /proc/mm...not found - PTRACE_FAULTINFO...not found - PTRACE_LDT...not found UML running in SKAS0 mode [1]+ Stopped mountlo -m 16 -d /dev/uba1 /home/vi/mnt/usb -t vfat -o iocharset=utf8,allow_other vi@vi-notebook:~/b$ bg [1]+ mountlo -m 16 -d /dev/uba1 /home/vi/mnt/usb -t vfat -o iocharset=utf8,allow_other & [1]+ Stopped mountlo -m 16 -d /dev/uba1 /home/vi/mnt/usb -t vfat -o iocharset=utf8,allow_other vi@vi-notebook:~/b$ bg [1]+ mountlo -m 16 -d /dev/uba1 /home/vi/mnt/usb -t vfat -o iocharset=utf8,allow_other & [1]+ Stopped mountlo -m 16 -d /dev/uba1 /home/vi/mnt/usb -t vfat -o iocharset=utf8,allow_other vi@vi-notebook:~/b$ bg [1]+ mountlo -m 16 -d /dev/uba1 /home/vi/mnt/usb -t vfat -o iocharset=utf8,allow_other & [1]+ Stopped mountlo -m 16 -d /dev/uba1 /home/vi/mnt/usb -t vfat -o iocharset=utf8,allow_other vi@vi-notebook:~/b$ fg mountlo -m 16 -d /dev/uba1 /home/vi/mnt/usb -t vfat -o iocharset=utf8,allow_other Linux version 2.6.15 (miko@dorka) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Mon Feb 27 13:27:52 CET 2006 (normal output) ... vi@vi-notebook:~/b$ socat - exec:'mountlo -m 16 -d /dev/uba1 /home/vi/mnt/usb -t vfat -o iocharset=utf8\,allow_other',pty,ctty fusermount: waitpid: No child processes vi@vi-notebook:~/b$ Also happens with Gimp (when it does run it's plug-ins). Parts of Gimp started by `gimp q.jpg&' freeze and cannot continue unless "killall -CONT" or made foreground. Is it a bug? How to reliably start things in a background?

  Read the article

• Network is going down once per day

  - by Charly

  Once per day the network on eth0 is going down and we need to do sudo ifdown eth0; sudo ifup eth0 to get the network up. Here is the syslog: Feb 11 12:48:01 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 12:52:35 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 12:56:23 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:00:28 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:04:29 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:09:16 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:13:53 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:18:16 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:22:25 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:26:52 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:30:44 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:31:49 www-tech-1 dhclient: There is already a pid file /var/run/dhclient.eth0.pid with pid 3198 Feb 11 13:31:49 www-tech-1 dhclient: Listening on LPF/eth0/00:e0:81:49:fc:e0 Feb 11 13:31:49 www-tech-1 dhclient: Sending on LPF/eth0/00:e0:81:49:fc:e0 Feb 11 13:31:49 www-tech-1 dhclient: DHCPRELEASE on eth0 to 131.121.113.228 port 67 Feb 11 13:31:49 www-tech-1 dhclient: There is already a pid file /var/run/dhclient.eth0.pid with pid 134519072 Feb 11 13:31:50 www-tech-1 dhclient: Listening on LPF/eth0/00:e0:81:49:fc:e0 Feb 11 13:31:50 www-tech-1 dhclient: Sending on LPF/eth0/00:e0:81:49:fc:e0 Feb 11 13:31:52 www-tech-1 dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 Feb 11 13:31:52 www-tech-1 dhclient: DHCPREQUEST of 131.121.14.17 on eth0 to 255.255.255.255 port 67 Feb 11 13:31:53 www-tech-1 kernel: [265383.991682] eth0: no IPv6 routers present Please check the last portion of this syslog. Can anybody help me?

  Read the article

• Communicating with the PC via USB connection in Android

  - by Danny Singh

  I'm fairly new to android programming and need some information for a 4th year forensics course project. Basically I am trying to create a suite of tools for live analysis of an android phone. I know how to get the information I need on the phone, but I was wondering if there was a way to communicate that information back to the PC? I want to be able to run a program from a PC, which, when the phone is docked, will allow the user to access information about the phone (ie currently running services/processes, bluetooth/wifi connections, etc). I have a bunch of methods that will run on the phone and get all the information, but I want to be able to call those methods from the PC, execute on the phone, then have the information sent back to the PC to display to the user instead of just displaying it on the phone. This is to leave as small a footprint on the phone as possible. Thanks a lot.

  Read the article

• configure squid3 to set up a web proxy in ubuntu12.04

  - by Gnijuohz

  I am in a LAN and have to use a proxy given to access the web in a very limited way. I can't even use google, github.com or SE sites. However I can use ssh to log into a server, which I have root access so basically I can do anything I want with it. So I was thinking that maybe I could use that server as a proxy so I can visit sites through it. I tested it using ssh -vT [email protected] which gave a proper response. And In my computer I can't do this. Also I tried downloading something from the gun.org using wget, which can't be done in my computer too. And it succeeded on that server. I don't know if that's enough to say that this server have full access to the Internet. But I assumed so and I installed squid3 on it. After trying some while, I failed to get it working. I got this after I run squid3 -k parse 2012/07/06 21:45:18| Processing Configuration File: /etc/squid3/squid.conf (depth 0) 2012/07/06 21:45:18| Processing: acl manager proto cache_object 2012/07/06 21:45:18| Processing: acl localhost src 127.0.0.1/32 ::1 2012/07/06 21:45:18| Processing: acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 2012/07/06 21:45:18| Processing: acl localnet src 10.1.0.0/16 # RFC1918 possible internal network 2012/07/06 21:45:18| Processing: acl SSL_ports port 443 2012/07/06 21:45:18| Processing: acl Safe_ports port 80 # http 2012/07/06 21:45:18| Processing: acl Safe_ports port 21 # ftp 2012/07/06 21:45:18| Processing: acl Safe_ports port 443 # https 2012/07/06 21:45:18| Processing: acl Safe_ports port 70 # gopher 2012/07/06 21:45:18| Processing: acl Safe_ports port 210 # wais 2012/07/06 21:45:18| Processing: acl Safe_ports port 1025-65535 # unregistered ports 2012/07/06 21:45:18| Processing: acl Safe_ports port 280 # http-mgmt 2012/07/06 21:45:18| Processing: acl Safe_ports port 488 # gss-http 2012/07/06 21:45:18| Processing: acl Safe_ports port 591 # filemaker 2012/07/06 21:45:18| Processing: acl Safe_ports port 777 # multiling http 2012/07/06 21:45:18| Processing: acl CONNECT method CONNECT 2012/07/06 21:45:18| Processing: http_port 3128 transparent vhost vport 2012/07/06 21:45:18| Starting Authentication on port [::]:3128 2012/07/06 21:45:18| Disabling Authentication on port [::]:3128 (interception enabled) 2012/07/06 21:45:18| Disabling IPv6 on port [::]:3128 (interception enabled) 2012/07/06 21:45:18| Processing: cache_mem 1000 MB 2012/07/06 21:45:18| Processing: cache_swap_low 90 2012/07/06 21:45:18| Processing: coredump_dir /var/spool/squid3 2012/07/06 21:45:18| Processing: refresh_pattern ^ftp: 1440 20% 10080 2012/07/06 21:45:18| Processing: refresh_pattern ^gopher: 1440 0% 1440 2012/07/06 21:45:18| Processing: refresh_pattern -i (/cgi-bin/|?) 0 0% 0 2012/07/06 21:45:18| Processing: refresh_pattern (Release|Packages(.gz)*)$ 0 20% 2880 2012/07/06 21:45:18| Processing: refresh_pattern . 0 20% 4320 2012/07/06 21:45:18| Processing: ipcache_high 95 2012/07/06 21:45:18| Processing: http_access allow all I deleted some allow and deny rules and added http_access allow all so that all the request would be allowed. After configuring my computer, I got this error: Access control configuration prevents your request from being allowed at this time. Please contact your service provider if you feel this is incorrect. And the log in the server showed that my TCP requests had all been denied. So, first of all, is what I am trying to do achievable? If so, how to configure the squid in the server so that I use it as a proxy to surf the Internet? My computer and the server both run Ubuntu11.04. Thanks for any help~

  Read the article

• Graphics driver for ubuntu on dell latitude XT

  - by marc.riera

  we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

  Read the article

• Squid Proxy: url_regex acl is not working?

  - by bharathi

  I am using squid proxy 3.1 in ubuntu machine. I want to allow only urls matching our pattern through our proxy server. I configured acl like below. Acl for dstdomain is working fine. If i access any url besides .zmedia.com , I got proxy connection refused. But the url_regex is not working. What i am trying here is. Allow only request from ".zmedia.com" domain and the request url should be in "/blog" context. # # Recommended minimum configuration: # acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 ::1 acl urlwhitelist url_regex -i ^http(s)://([a-zA-Z]+).zmedia.com/blog/.*$ acl allowdomain dstdomain .zmedia.com acl Safe_ports port 80 8080 8500 7272 # Example rule allowing access from your local networks. # Adapt to list your (internal) IP networks from where browsing # should be allowed acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl SSL_ports port 7272 # multiling http acl CONNECT method CONNECT # # Recommended minimum Access Permission configuration: # # Only allow cachemgr access from localhost http_access allow manager localhost http_access deny manager http_access deny !allowdomain http_access allow urlwhitelist http_access allow CONNECT SSL_ports http_access deny CONNECT !SSL_ports # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # We strongly recommend the following be uncommented to protect innocent # web applications running on the proxy server who think the only # one who can access services on "localhost" is a local user #http_access deny to_localhost # # INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS # # Example rule allowing access from your local networks. # Adapt localnet in the ACL section to list your (internal) IP networks # from where browsing should be allowed http_access allow localhost # And finally deny all other access to this proxy http_access deny all # Squid normally listens to port 3128 http_port 3128 # We recommend you to use at least the following line. hierarchy_stoplist cgi-bin ? # Uncomment and adjust the following to add a disk cache directory. #cache_dir ufs /var/spool/squid 100 16 256 # Leave coredumps in the first cache dir coredump_dir /var/spool/squid append_domain .zmedia.com # Add any of your own refresh_pattern entries above these. refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . 0 20% 4320 Please correct me , If i did anything wrong?

  Read the article

• CUPS causes printer to click and doesn't print

  - by Pez Cuckow

  I'm suffering a strange problem with my Cannon iP4850 when trying to use CUPS on a Raspberry Pi (this is not RPi specific, please do not vote to move it). When I plug the printer into my Laptop (OSX) or my Desktop W7 it identifies as a iP4800 and prints perfectly. So I plug it into the Pi (running debian), set it up in CUPS enable sharing and can now see the iP4800 series shared on the network. However if I print to it (using AirPrint etc...); the file gets to CUPS safely (shows in the queue) but when it tries to print the printer clicks (like a loud thunk) 3/4 times and then gives in, with a double amber flashing light. In cups it shows as job completed. Do you know why using the pi and cups would cause what appears to be a hardware fault and what I can do to fix the problem or to provide further debug info? Thanks for your time! Description: Canon iP4800 series Location: Lounge Driver: Canon PIXMA iP4800 - CUPS+Gutenprint v5.2.9 (color, 2-sided printing) Connection: usb://Canon/iP4800%20series?serial=2239B2 Note: I've tried deleting and re-adding the printer to the Laptop, Desktop and PI and the results are always the same Log for plugging in printer and printing (attempting to) something until the printer turned off again pi@pezpi /var/log $ dmesg [ 7284.176336] usb 1-1.2: new high speed USB device number 8 using dwc_otg [ 7284.279703] usb 1-1.2: New USB device found, idVendor=04a9, idProduct=10d5 [ 7284.279750] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7284.279771] usb 1-1.2: Product: iP4800 series [ 7284.279786] usb 1-1.2: Manufacturer: Canon [ 7284.279800] usb 1-1.2: SerialNumber: 2239B2 Setting cups to verbose: Change loglevel in cupsd.conf to debug (or debug2) pi@pezpi /var/log $ sudo vim /etc/cups/cupsd.conf pi@pezpi /var/log $ sudo /etc/init.d/cups restart [ ok ] Restarting Common Unix Printing System: cupsd. pi@pezpi /var/log $ Log from $ /var/log/cups/error_log is at http://pastebin.com/7VZMRMrG (too large to post here) The log contains - in order (deleted the log and then did the beneath) Restarting the cups server Attempting to print a test page x2 Printing from 192.168.1.90 via AirPrint Printing from 192.168.1.90 via Network Print Turning the printer off and on again

  Read the article

• Tomcat and IIS 7 both on different ip's and different ports

  - by n00b

  I have Tomcat and IIS 7 installed together on a Windows 2008 server. The machine has two IPs (134.133.1.1 and 134.133.2.2). I want Tomcat to handle 134.133.1.1, on port 80, and IIS to handle both 134.133.2.2, on port 80 AND 134.133.1.1, on port 443, but can't seem to get the last two together (I can get one or the other by themselves on IIS, along with the first IP address on Tomcat). I have configured Tomcat to successfully listen to ip 134.133.1.1, on port 80 with this configuration; <Connector port="80" protocol="HTTP/1.1" address="134.133.1.1" connectionTimeout="20000" redirectPort="8443" /> I also have a site configured in IIS bound to ip 134.133.1.1, on port 443 (SSL). When I turn on IIS, after Tomcat, I can reach both 134.133.1.1:80 (Tomcat) and 134.133.1.1:443 (IIS) successfully (as desired). The problem now comes when I want to introduce a new site via IIS, at the new ip address. In IIS I have setup a new site at IP 134.133.2.2, port 80. I can not start the site. The event log shows this error; Unable to bind to the underlying transport for [::]:80. The IP Listen-Only list may contain a reference to an interface which may not exist on this machine. The data field contains the error number. I think this is because IIS 7 tries to listen to port 80 on all IPs, and it cant because Tomcat is taking port 80 for 134.133.1.1. From reading, the resolution is to specify the IP address you want IIS to bind on port 80. The problem is, when I add 134.133.2.2 to the iplisten list, then I get a 404 when I try navigating to 134.133.1.1:443. I assume this is because IIS is no longer listening to ANY port on 134.133.1.1. How do I resolve this such that IIS will return both sites? EDIT: Per request my IIS binding for site A is 134.133.2.2 on port 80 (http) and 134.133.2.2 on port 443. For site B in IIS, the binding is 134.133.1.1 on port 443 (https). Note the IPs in this example are just for example purposes, but consistent with my setup.

  Read the article

• LACP : Cisco ASA 5515 & Switch ProCurve 2920

  - by user979276

  I've two ASAs 5515 connected in failover Active/Stand by (on Gi0/5) My two ASAs are connected to two Switch ProCurve 2920 to have HA if something happens. So I plug something like that (don't pay attention to the arrows) : So one the ASA, I created a Port-Channel like that : interface GigabitEthernet0/0 nameif outside security-level 0 ip address 192.168.1.3 255.255.255.0 standby 192.168.1.4 ! interface GigabitEthernet0/1 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface GigabitEthernet0/2 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface Port-channel1.1 vlan 1 nameif inside security-level 100 ip address 192.168.8.1 255.255.255.0 standby 192.168.8.2 ! interface Port-channel1.10 vlan 10 nameif guest security-level 50 ip address 172.16.100.2 255.255.255.224 standby 172.16.100.3 ! interface Port-channel1.16 vlan 16 nameif dmz security-level 50 ip address 192.168.16.1 255.255.255.0 standby 192.168.16.2 On the switch, I created a trunk LACP capable with the port 1 and 2 on each switch, force the speed to 1000 and put the port un full duplex mode. BUT this is not working... I tried many things and I can't make it work. In this configuration, I can't ping anything between my ASA and my Switch (or any object connected). Here what I get on my ASA : Channel group 1 LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State ----------------------------------------------------------------------------- Gi0/2 SP not-bndl 32768 0x1 0x1 0x3 0xc Gi0/1 FP not-bndl 32768 0x1 0x1 0x2 0x6 And on the Switchs : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Broken Yes Failure 2 Active trk1 Broken Yes Failure If I change the Cisco interface to LACP mode On, I can ping the switch from the ASA but nothing other objects conneted on the switch. If I look at the statut of LACP on the switch I see this : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Up No Success 2 Active trk1 Up No Success I don't have any clue on what's going on so If someone have any idea and help me on this, it would be great ! Feel free to ask me anything if you need any more information ! Thanks a lot !

  Read the article

< Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >