Search Results

Search found 8824 results on 353 pages for 'cloud virtualization vmware density scalability'.

Page 158/353 | < Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >

• Routing table with two NIC adapters in libvirt/KVM

  - by lzap

  I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

  Read the article

• Build a server in KVM linux

  - by Lai Yu-Hsuan

  I owned a linux server. Now there are several users want to build web services on it, but they require different enviroments. For convenience I give a KVM virtual machine root permission to each user. But obviously the linux server has only one IP. How can I deliver the external requests to corresponding virtual machine? (I expect it's somewhat complicated. If so I want at least some docs/websites I can start reading.)

  Read the article

• Prioritizing a KVM virtual machine

  - by Joril

  I have a CentOS 6.2 server running a few KVM VMs, how can I prioritize one of them above the others? I tried: virsh dumpxml vm > vm.xml and then adding to vm.xml <cputune> <shares>10240</shares> <period>100000</period> <quota>-1</quota> </cputune> and then virsh define vm.xml but it looks like nothing changed... Am I missing something? How could I check if my "cputune" is in effect?

  Read the article

• libvirt upgrade caused vms to not see drives (boot media not found)

  - by bias

  I upgraded to Ubuntu 12.04.1 and now libvirt (via open nebula) successfully runs vms but they aren't finding the 2 drives (specifically, the boot drive). One is "hd" the other is "cdrom". The machine boots but fails and displays something like "boot media not found hd" (this was in a vnc terminal and I didn't copy the output anywhere so that's not the verbatim message). I tried constructing a new disk using the new version of qemu (via vmbuilder) and this new machine has the same problem as the old machine. In case it matters (I can't see why it would) I'm using open nebula to manage the machines. There's nothing relevant in any of the logs: syslog, libvirtd, oned. Which is to say nothing interesting/anomalous is reported when the machine is brought up. Versions libvirt 0.9.8-2ubuntu17.4 qemu-kvm 1.0+noroms-0ubuntu14.3 The libvirt xml config portions (relavent) <os> <type arch='x86_64' machine='pc-1.0'>hvm</type> <boot dev='hd'/> </os> ... <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='qcow2'/> <source file='/var/lib/one//203/images/disk.0'/> <target dev='sda' bus='scsi'/> <alias name='scsi0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='file' device='cdrom'> <driver name='qemu' type='raw'/> <source file='/var/lib/one//203/images/disk.1'/> <target dev='sdc' bus='scsi'/> <readonly/> <alias name='scsi0-0-2'/> <address type='drive' controller='0' bus='0' unit='2'/> </disk> <controller type='scsi' index='0'> <alias name='scsi0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </controller> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </memballoon> ... </devices> The libvirt/qemu log contains 2012-11-25 22:19:24.328+0000: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-1.0 -enable-kvm -m 256 -smp 1,sockets=1,cores=1,threads=1 -name one-204 -uuid 4be6c276-19e8-bdc2-e9c9-9ca5352f2be3 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/one-204.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -device lsi,id=scsi0,bus=pci.0,addr=0x5 -drive file=/var/lib/one//204/images/disk.0,if=none,id=drive-scsi0-0-0,format=qcow2 -device scsi-disk,bus=scsi0.0,scsi-id=0,drive=drive-scsi0-0-0,id=scsi0-0-0,bootindex=1 -drive file=/var/lib/one//204/images/disk.1,if=none,media=cdrom,id=drive-scsi0-0-2,readonly=on,format=raw -device scsi-disk,bus=scsi0.0,scsi-id=2,drive=drive-scsi0-0-2,id=scsi0-0-2 -netdev tap,fd=18,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3 -netdev tap,fd=19,id=hostnet1 -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4 -usb -vnc 0.0.0.0:204 -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x6 kvm: -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom" kvm: -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom"

  Read the article

• How to install a "virtual" network card on a virtual server?

  - by vikp

  Hi, We have purchased an unmanaged VPS windows hosting solution from one of the UK based companies. We have Windows Server 2008 Standard Edition. We need to install certain third party applications on that server. Unfortunatelly, one of the applications requires a MAC address to be present at all times - this is their way of making sure that software is not pirated (which it isn't). We have tried installing a virtual loopback network card, but this has brought the server down - i.e. we couldn't connect using remote desktop any longer. At the moment we are limited with what we can try. This is an unmanaged solution, therefore any support including restarts is rather costly. Are you aware of any low-risk solutions? Thank you

  Read the article

• Rails Hosting - Is RailsPlayground.com a Good Host?

  - by stringo0

  My team is currently looking into hosting for RoR apps, and we're considering RailsPlayground, Linode and SliceHost. We haven't found anyone recommending rails playground, and web of trust seems to caution against it - http://www.mywot.com/en/scorecard/railsplayground.com I like the fact that they give you a sourcerepo account for free to host and track git repos, etc. The Questions: Is there any reason not to go with RailsPlayground? Have you had any negative experiences with RailsPlayground? (Feel free to share positives as well) Thanks!

  Read the article

• Can I boot up a virtual machine natively?

  - by Anshul

  My question is: Is is possible to run a virtual machine natively on your hardware if you have installed the proper drivers etc? In other words, can I use a VHD as a regular hard drive to boot from? The reason I want to do this is that I do both graphics-intensive and audio-intensive work, but my computer is not powerful enough to handle both at the same time and many times I install a bunch of audio programs that I don't want affecting the stability of my graphics programs. Basically I wanted to have sandboxing between the two sets of applications. So I tried running the graphics-intensive programs in a VirtualBox VM and the audio-intensive work natively (simply because it's a pain to route ASIO audio devices in/out of VirtualBox). This kind-of works - the graphics-intensive stuff is tolerable, but still relatively slow, because it's running inside a VM. So my next idea was to just dual-boot and install the graphics and audio programs in separate partitions but I frequently use them in tandem, so it wouldn't be practical to reboot my machine every time I need to use the other set of programs. But I could live with this scenario: If I need to do more audio-intensive stuff, I'll just boot up to the audio partition and run the graphics programs in a VM, and then when I'm working heavily on the graphics part, I'll just boot the graphics partition as a regular OS directly on the hardware. Is this possible? For example by booting up a VHD as a regular hard drive? Or by setting up dual-boot, and every time the audio partition is shut down, synchronize the graphics VM VHD with the native graphics partition? Is it practical, given the above scenario? And if it's not possible, barring buying another computer, can anyone suggest a best-of-all-worlds setup (the two worlds being performance, sandboxing, and running in parallel) for the above scenario? Thanks in advance.

  Read the article

• Access VirtualBox-ed server from behind the router

  - by migajek

  I'm having the following configuration: Windows 7 hosting VirtualBox and it's guest: Ubuntu The machine (physical) which runs VirtualBox is behind the router and has the address of 192.168.0.110 VirtualBox runs the Bridged network, and the IP of VirtualBox-ed Ubuntu (eth0) is 192.168.0.200 Host (Win7) is running HTTP service on port 80, while guest (Ubuntu) is running it's service on port 9000 I can access both services from inside the network by typing the ip_address:port and this works fine. Both ports are forwarded on the router to their's respective IPs: 80 -> 192.168.0.110:80 9000 -> 192.168.0.200:9000 Unfortunately, accessing the router's external IP doesn't work as expected. While external_ip:80 works correctly, external_ip:9000 - doesn't I believe the problem is VBox - related, since the same network is running also other physical machine with Ubuntu and http service on 8000 and this one is forwarded correctly.

  Read the article

• Remote desktop to my KVM virtual machine

  - by user6

  I've got a dedicated server running Debian 6. I've set up a windows 7 virtual machine using KVM. Now I'm trying to get Remote desktop working. I'm guessing i have to do some port forwarding. The virtual machine is in a NAT. Remote desktop is already set up on it (another virtual machine can connect). I've tried using the iptables and countless of virsh commands of which I'm not even sure what they did. Anyone knows how to get this working?

  Read the article

• USB webcam detected in KVM, but doesn't work

  - by Gene Vincent

  I have installed XP in a virtual machine running on Linux with QEMU/KVM (qemu-kvm-0.11.0-4.5.2). I export my Linux webcam to KVM using the switches "-usb -usbdevice host:046d:0929". The XP guest sees the webcam and the drivers install, but the camera only shows a black image. When I open the camera in Windows Explorer, it says "0 images" and a black image, while on a real XP, it says "1 image" and shows the video from the camera. I tried the same with a different webcam, but the result is the same. Any ideas what might be wrong or how I could debug this ?

  Read the article

• Running SQL 2008 on a VM

  - by chris.w.mclean

  We are pondering trying to set up a SQL 2008 instance inside a VM for a production environment. All our SQL instances use iSCSI over gigabit ethernet to talk to a NAS, as would this new instance. Any reason this is a bad idea or any considerations to make this work well? The VM would be running in Xen 5.5 or we could set it up in Hyper-V if there's a compelling case for that. And the VM's VHD would be stored on a different NAS then the SQL storage is on.

  Read the article

• Route multiple subdomains on one external ip to multiple internal ips

  - by Abenil

  i have several subdomains(git.example.org, build.example.org, etc.), i have a router with an external ip and i have several virtual machines on a host computer with internal ips. Now i want to route git.example.org to internal ip 10.0.2.1 and build.example.org to internal ip 10.0.2.2. How can I do this? I setup in the Router that all traffic on port 80 is comming to my host computer with internal ip 10.0.2.3 and installed Squid on that computer. I added the following lines to the squid.conf file: cache_peer 10.0.2.1 parent 80 0 no-query originserver name=server_1 cache_peer_domain server_1 git.example.org cache_peer 10.0.2.2 parent 80 0 no-query originserver name=server_2 cache_peer_domain server_2 build.example.org But this is not working for me. :( Any help appreciated. Regards Nils Update: Here is the solution for Apache http://serverfault.com/a/273693

  Read the article

• Windows Server 2003 guest on Xen frequently stops responding

  - by smokris

  I'm running a Windows Server 2003 guest instance in Xen 3.x. This DomU runs fine for a day or two, then stops responding — I don't get any network response, and I can no longer connect to Xen's VNC console for this DomU. xm list shows this: Name ID Mem VCPUs State Time(s) Domain-0 0 6508 8 r----- 1161159.4 [A working Linux DomU] 1 512 1 -b---- 68711.1 [The hung Windows DomU] 5 512 1 ------ 67234.2 [Another working Linux DomU] 3 512 1 -b---- 163036.4 (What does the ------ mean? The xm manual explains what each of the six states mean, but not what no-state means.) If I xm destroy and then xm create the Windows DomU again, it boots right back up (with the Windows alert The previous system shutdown at [...] was unexpected.), and then stops responding after another day or two. I checked /var/log/xen/*.log, but no log messages are generated at the time the server stops responding. How should I proceed in troubleshooting this?

  Read the article

• Why is it I can't use my Windows installation both as a host and a guest?

  - by Josef

  I have Linux installed on my harddrive, sometimes I run it as the host operating system and sometimes run it as a guest in Windows using VirtualBox. It's a nice ability, I think. I don't think it's possible with Windows though. Is it because your average distribution includes drivers for everything known to man? Are devices/drivers configured statically in Windows so when somethings changed it breaks?

  Read the article

• How do I configure networking on CentOS 6 running on hyper-v?

  - by LonelyLonelyNetworkN00b

  I'm not using legacy adapters, and i've installed Linux Integration Components 3.2. THe problem i'm facing is that the command 'setup' or 'system-config-network' doesn't list any network interfaces. If i run ifconfig -a i can see both the network cards i've attached. By setting a ip using ifconfig i can get network connectivity. The problem is that it's not persistent after a reboot. I'm a 100% centos newbie, but I figure it has something to do with that the centos installer couldn't see the NICs on install. How can I fix this?

  Read the article

• Virtual IPv6 Network between VirtualBox VMs

  - by Ben

  I'm trying to create a virtual IPv6 network as a test environment. I have 5 VirtualBox VMs (Ubuntu Server) with network adapters using host-only networking. You can imagine them being connected in series and every machine connects 2 subnets. I want to ping the last machine from the first one: On: 2001:db8:aaaa::100 I want to ping 2001:db8:dddd::101 (Note: there is no cccc network in between) Only static configuration and routes are used: /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::100 netmask 64 /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::101 netmask 64 auto eth1 iface eth1 inet6 static address 2001:db8:bbbb::100 netmask 64 up ip -6 route add 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 down ip -6 route del 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 I thought there might be some automatic route discovery going on. Anyway, ping6 2001:db8:dddd::100 will not work from aaaa::100 When I add the route: ip -6 route add 2001:db8:dddd::/64 via 2001:db8:aaaa::101 it will work. But the next interface in the same network dddd::101 is not reachable. How could that be? There is a machine with an interface bbbb::101 and another dddd::100 and I can ping the latter one, but the machine connected to it, dddd::101 not?? I also have also turned on forwarding. Any ideas?

  Read the article

• Xen and Ubuntu?

  - by wag2639

  How does one properly approach having Ubuntu servers on a Xen hypervisor? I don't have any experience with RAID or Xen other than from a theoretical level. Additional requirements: Use with mdadm Software RAID 5 (can be on separate disks) that multiple instances with access Paravirtualized Ubuntu Server guests instances Possible ideas for now: Ubuntu host (dom0) with ubuntu-xen-server package (this purportedly isn't supported) dom0 host will "own" RAID 5 partition More Ubuntu servers as guests Citrix XenServer bare-metal host XenServer will own RAID Citrix XenServer bare-metal host Ubuntu guest instance creates and owns RAID Questions and concerns: Can Ubuntu be used as a dom0 Xen host? Can XenServer install packages such as mdadm and create a partition? Can multiple guest access (R + W) to the same data partition (RAID)? Note: since it may have a bearing on support, I'm referring to Ubuntu Server 10.04

  Read the article

• KVM and libvirt: How to configure a new disc device to an existing VM?

  - by initall

  I've got an Ubuntu 9.04 server running two VM's. In /etc/libvirt/qemu/machine1.xml two disk devices are defined like this: <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <source file='/vserver/machine1/disk0.qcow2'/> <target dev='hda' bus='ide'/> </disk> <disk type='file' device='disk'> <source file='/vserver/machine1/disk1.qcow2'/> <target dev='hdb' bus='ide'/> </disk> I need more storage space in at least one of the devices and thought about adding a third hdc device by simply adding one with same style as above and re-organising my mount structure (The virtual sizes of the current qcow2 files are unfortunately limited.) My problem is that reloading libvirtd and restarting the VM do not result in a new visible device (checked with fdisk). I'm aware of extending an existing qcow2 file (converting to raw format, cat-ing/adding the new one, using smth. like gparted) - but only as a last resort. Hopefully it's something very simple I'm missing?

  Read the article

• Unusable Source for Ubuntu image on Xen 3

  - by Roberto Aloi

  Hi all, I'm trying to create a new VM in Xen 3, running Ubuntu 10.4 (32 bit) as the guest OS. Xen 3 is installed on a machine running OpenSuse 11.2. I downloaded the Ubuntu image from the ubuntu.com website and I mounted it on /dev/loop0. When I try to create the new VM in Xen with the given source, Xen complains the "source is unusable". I've also checked the md5 sum for the image. It's fine. Any suggestion or hint that could help me?

  Read the article

• Looking for advice on Hyper-v storage replication

  - by Notre1

  I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

  Read the article

• I need a few minutes of dedicated server a week, but not for hosting, just to convert ogg etc

  - by talkingnews

  I'm completely happy with my webhosting, it's just that I need to do one little thing they won't allow, and that's run an instance of Sox to convert about 30 mp3s to ogg files, in various directories, a couple of times a week, to be done automatically in response to the detection of the upload of an mp3. Probably looking at a minute of server time over the whole week. I've had unhelpful suggestions on other forums like "why not leave your home PC on 24 hours a day and then use all your isp bandwidth to do this", which doesn't work for me. I know that I can host files on, say, Amazon S3, but is there something similar for my needs? All it would need to do would be: wget/ftp the mp3 files, convert them to ogg, ftp the files back to my hosting. Of course, all this wouldn't be needed if there was such a thing as a compiled binary of Sox (or any mp3ogg converter) for Centos which I could upload without needing root access, but I've given up asking that one, but always open to suggestions!

  Read the article

• Create a VHD from a physical XP machine

  - by runxc1

  I am looking at upgrading from Windows XP to Windows7. I have a lot of development programs that would take 2-3 days to set-up configure etc. etc. when I get my new machine. What I want to do is create a VHD of my physical XP machine install Windows 7 and then operate out of my Virtual PC while I take the time to configure Windows 7. Is this possible to do? If so how do you do it?

  Read the article

• KVM Hosting: How to efficiently replicate guests

  - by javano

  I have three KVM servers each with 1 guest VM, running directly on it's local storage, (so they are essentially getting a dedicated box worth of computing power each). In the event of a host failure I would like the guests replicated to at least one of the other hosts so I can spin it up there, until the failing host is fixed. I am curious about KVM cloning. I can clone a VM live or when it's suspended/shutdown. Obivously suspended VMs will naturally be quicker to clone but these three VMs comprise three parts of a single solution, so I don't want to ever have any one of them shutdown. How can I efficiently clone these VMs between servers? I have had a couple of ideas, but are these insane or, is there a better method I have missed for my scenario? Set up a DRDB partition between box 1 and 2 where VM 1 runs from, and so is replicated between box1 and box 2, repeat between box 2 & 3, and box 3 & 1 (This could be insane, I have never used DRDB only read about it) Just use standard KVM CLI clone options to perform live clones (I'm dubious about this because I don't know how long it will take and what the performance impact will be during) Run a copy of each VM on at least one other host, and have the guest on one host export it's data to the matching guest on another host where it can import that data, scripting this on the guest) Some of other way? Ideas welcome! Side Note These servers have 4x15k SAS drives in a RAID 10 so they aren't rocketing fast, and as I mentioned, each VM runs from the host's local storage, no NAS or SAN etc. So that is why I am asking this question about guest replication. Also, this isn't about disaster recovery. Guests will be exporting their data to a NAS over a VPN, so I am looking at how I can have them quickly spun up in a host failure situation.

  Read the article

• How to implement a virtual server running Ubuntu inside a fileserver in windows?

  - by user541445

  I work in a company that has some limitations regarding their budget. They need client/server aplication. I can code the aplication, I've made mini tests on primordial applications that work. The thing is that they only have fileservers, and the application they need must be concurrent compliant, so the database must be in their local network (Fileserver is the only choice). So far, I have explored almost any option available, starting with: Desktop databases. Access (We have a license)(But concurreny is just not effective, besides it's a windows software, yuck). Sqlite (Nice, but since the information they manage is a lot, I've performed some concurrency tests with INSERTs and doing SELECTS at the same time). It fails, somehow it just stops inserting. Open office Base (I dismember a base office only to see that it was a file mode HSQLDB). I've tried, not concurrent at all. Etc (You name the Open source Desktop Database manager, and yes, I've tried that one.) Server databases Call me a stubborn person, but reading some server databases documentation say that their databases will work in a file mode. I've tried a lot of products. Postgres, MySQL, FireBird, H2, Derby, Oracle Express, IBM DB2 Express, etc. So, I really need a hand here, I've been doing this install/delete/depression thing with a lot of databases for 3 weeks, until I got with a crazy idea and I just came here to express it. So, my question comes down to this: Installing a light virtual OS software like Virtual PC and then installing in there a Server OS like an Ubuntu server inside that virtual software will work? Will it work 24/7 or when I close the virtual pc software? Will this work in a fileserver? Any suggestion, answer, critic to the place I work, crazy new concurrent database that will work in fileserver will be most than welcome.

  Read the article

• KVM Guest Reboot Loop

  - by javano

  I have been pulled into a situation where a KVM server (CentOS 6.2) lost power and upon reboot one of the guests hasn't started up again (XP SP3). I have SSH'ed in and someone must have changed something relating to the hyper visors prior to the power loss, but not rebooted all the guests. This particular guest wouldn't start because it was configured to use /usr/bin/qemu-system-x86_64 which isn't there now (assuming it was before?). I changed it to use /usr/libexec/qemu-kvm as this is what all the other guests on this server seem to be using, and its booting up. Using virt-manager on my local machine I can connect to the display of the XP machine and it gets as far as this screen; http://support.gateway.com/emachines/issues/2-1131285152-01.gif The problem I face now, is that which ever option I choose the machine just reboots. So it's and endless loop. I thought that perhaps a file system error maybe present due to the unclean shutdown. There is an XP SP3 ISO mounted under the guest, which I booted from in an attempt to access the recovery tools, but I don't have the Administrator password! I am out of ideas, and it's turning out to be quite the conundrum. Should I use a 3rd party live CD to test the FS for errors? How else can I trouble shoot these restarts?

  Read the article

< Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >