Search Results

Search found 14989 results on 600 pages for 'street address'.

Page 158/600 | < Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >

  • Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

    - by Bo102010
    (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

    Read the article

  • Networking DOS within Windows 7 XP Mode, with a Windows XP/7 Networked Share

    - by theonlylos
    For awhile now, one of my clients has been stuck with Corel Paradox 4.0 (it used to be the biggest database system in the DOS days, until Microsoft released Access in the early 90's) so for awhile I've managed to keep it on life support on Windows XP for a few years, however since switching to Windows 7 x64, I've had to resort to using XP Mode as the sandbox to keep it up and running. While I am able to run Paradox as usual in XP Mode, I'm having a serious issue where if I try connecting the install to the network share (which is located on the Windows 7 portion of the system), Paradox keeps exiting because it says the serial number is invalid. Now, I know for a fact that this is an issue with the virtual loopback adapter and also having the VM linked to the physical ethernet adapter -- and while I have solved this issue before, most of my fixes have been bandages since after a few weeks the issue pops up again. Long story short, I wanted to ask if there is a permanent way to link a DOS program to a network share address. For example, when I try doing \tsclient\paradox (the Windows 7 Address) I keep getting an error saying I need a valid network address. I've tried mapping that folder to various drive letters such as P:\Paradox -- but for some reason that keeps failing over time. For what it's worth, Paradox uses a .SOM file to store the network settings, however it isn't editable in Notepad but rather it's controlled by a wizard in Paradox. But if that extension rings any bells, I'd welcome any insights.

    Read the article

  • Programmatically add/delete users in Exchange

    - by Terry Gamble
    I've got the following set up: ASP.Net site that allows my internal employees to add in new hire information (no secure data, just stuff like name/address/phone) and when they submit this it goes into a database (SQL). Every few minutes a service runs that checks the database and if there are new entries it will add them into Exchange. The issue is I'm not happy with the way the service is doing things, (It's not putting address, etc in it). As I don't have the source code this I'm thinking of recreating it. My issue though is finding a starting point even. I know I'll have to create the scripts through code where the data is retrieved from SQL : Joe Smith 123 Main Street Nowhere, USA 19999 And put that into a powershell cmdlet (not sure exactly the syntax but I can get that figured out unless someone already has it) where the user is created in the Active Directory as a normal user and the mailbox is created simultaneously. From there I just need to fill out fields in Active Directory with the person's address, etc. Finally a deletion routine for when we terminate someone, however I'm sure that it will simply be a cmdlet that is easily shelled out to much like the initial one is, once I can figure out how to start that... Anyone have some good reference points or have already done it and can share?

    Read the article

  • How do I determine whether this email bounce is my fault?

    - by David Zaslavsky
    I use Google Apps to handle email for my personal website, so I have an email address [email protected] through that, and I also have a Gmail account [email protected]. Now, I've been trying to send emails to a particular recipient who shall be known as [email protected]. When I send the email from my Gmail account with the @gmail.com address, it works fine. However, when I send it from my Google Apps account with the @ellipsix.net address, I get a bounce message which includes the following text: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 554 554 mail server permanently rejected message (#5.3.0) (state 17). The bounce message suggests that it is up to the mail administrator of the recipient domain example.com to fix the problem, whatever it is. But I would like to be as sure as possible that nothing needs to be fixed on my end. I already have DKIM signatures enabled for my domain, and I have published an SPF DNS record. Is there something else I should check or do, or can I be confident that it's up to the recipient to fix this issue? Does the "state 17" in the bounce message mean something relevant? I've included my domain name in the question so people who know more than me about this stuff can independently check the relevant DNS records or other information. This other question seems similar, but I've already investigated everything suggested in the answers there (except for contacting Google, which I don't want to do unless I suspect it's their issue to fix).

    Read the article

  • exim4 to relay emails

    - by Matthieu
    I have exim4 installed on a Linux box. The basics work fine and I can send email from that machine without any problem to whatever email address. I also have a printer/scanner which is capable to send scans as emails. It needs an SMTP gateway to be able to do that. So I give the IP address of that Linux box, changed the configuration a little bit but still cannot get it to work. After I run dpkg-reconfigure exim4-config, here is what I get in /etc/exim4/update-exim4.conf.conf : dc_eximconfig_configtype='internet' dc_other_hostnames='' dc_local_interfaces='127.0.0.1;192.168.2.2' dc_readhost='' dc_relay_domains='mycompanyemail.com' dc_minimaldns='false' dc_relay_nets='192.168.2.0/24' dc_smarthost='' CFILEMODE='644' dc_use_split_config='false' dc_hide_mailname='' dc_mailname_in_oh='true' dc_localdelivery='mail_spool' My problem is that with this configuration, I can only send to emails @mycompanyemail.com... It says I can use wildcard, but when I do that, the '*' is replaced by whatever filename is in the directory where I run all that. How can I configure it to be able to send emails with any domain ? Or am I doing it wrong ? EDIT : here is the part of the log that's causing trouble : 2011-08-03 16:28:18 H=(NPI2D389C) [192.168.2.20] F=<[email protected]> rejected RCPT <[email protected]>: relay not permitted The first part ([email protected]) does not matter. I changed the email address. The point is that if this email is @mycompanyemail.com then everything works fine. Anything else does not work. I could add gmail.com, but I am looking to have any domain working...

    Read the article

  • can't ssh within LAN, but can connect from outside

    - by Patrick B.
    A strange issue: I have a desktop running Ubuntu 10.04 behind a Netgear WNR1000 router performing NAT. I would like to be able to ssh into the desktop from my laptop (running Windows 7 and Cygwin). When at home, both the desktop and the laptop are connected by wireless (the desktop is in a different room from the router). sshd seems to be running fine, since ssh localhost from the desktop works without trouble. Also, ssh my.ip.address from my laptop when it is not behind the router works fine (I am forwarding port 22 on the router to my desktop). However, ssh same.ip.address from within the LAN fails with "Connection refused". ssh 192.168.local.ip.address fails with a different message, "Connection timed out". I can connect if I first ssh to a machine outside the LAN. So far I haven't found anything with Google because with the search terms that seem like they would be relevant, the vast majority of people have the opposite problem - i.e., they can't connect from outside the LAN but can connect within it. I can port forward through a remote server when I'm at home, but this seems like a totally absurd way to connect two computers on the same home LAN. I have already tried stopping and starting sshd on the desktop. Any thoughts?

    Read the article

  • OS X won't see Windows 7 in network (and vice versa)

    - by meds
    I've enabled SMB sharing in OS X Lion and have added folders to share, it says 'Windows Sharing: On' with a green circle next to it (from the sharing window) and that to access the volume I will need to to go to \\192.168.0.17. It also says that the OS X should be visible as 'macbook' in the network. Both my WIndows 7 and OS X are connected to the same network, yet when I try to go to \\192.168.0.17 or from the Mac try to go to my Windows system (smb://192.168.0.6) the two OSs don't see each other. Any ideas why? Attempting to ping the Mac from Windows results in this output in the command prompt: Pinging 192.168.0.17 with 32 bytes of data: Reply from 192.168.0.6: Destination host unreachable. Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.0.17: Packets: Sent = 4, Received = 1, Lost = 3 (75% loss), ipconfig in Windows is: Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::8918:efd1:b05c:890f%21 IPv4 Address. . . . . . . . . . . : 192.168.0.6 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.1 Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::98ab:63fc:3c07:d837%13 IPv4 Address. . . . . . . . . . . : 192.168.74.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::80ff:c575:7b50:3a10%14 IPv4 Address. . . . . . . . . . . : 192.168.21.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Tunnel adapter isatap.{2E97D0AE-9E18-4072-AC23-1979BA0DCB79}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{E260CE43-E9A7-4DE0-A88E-4EAFF68ACDDB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{A5130812-59CE-4DDF-9C35-9433BCED9831}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{134BCAE7-CFFF-4A98-8DA0-3708806AABEB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{8D9E3B8F-161C-4ACE-B211-3EDD694416B2}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : in OS X: lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 stf0: flags=0<> mtu 1280 en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=2b<RXCSUM,TXCSUM,VLAN_HWTAGGING,TSO4> ether c8:2a:14:01:24:c1 media: autoselect (none) status: inactive en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether e0:f8:47:0c:fe:04 inet6 fe80::e2f8:47ff:fe0c:fe04%en1 prefixlen 64 scopeid 0x5 inet 192.168.0.17 netmask 0xffffff00 broadcast 192.168.0.255 media: autoselect status: active p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304 ether 02:f8:47:0c:fe:04 media: autoselect status: inactive fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078 lladdr 70:cd:60:ff:fe:d8:f1:32 media: autoselect <full-duplex> status: inactive

    Read the article

  • Connecting to IPv6 hosts when mobile and on a Surface?

    - by Cerebrate
    Specifically, at my usual location, I have an IPv6 network which connects to the Internet via a static tunnel set up to Hurricane Electric's tunnel broker ( http://www.tunnelbroker.net/ ). This works essentially perfectly, allowing inbound and outbound connectivity. Now, however, I need to connect back to host(s) on that network over IPv6 from mobile tablet(s); meaning the conditions are such that there is no guarantee or even likelihood of native IPv6 support where it happens to be at any given time, and the IPv4 address of the tablet will change on a fairly regular basis. The native Teredo support, as configured by default, functions well enough to let me ping my target hosts, but appears to have neither the reliability nor the throughput to support anything else; I have been unable to make any actual connections (trying a number of TCP-based protocols) using it. I had considered setting up an independent tunnel for the tablet(s), and using scripts to update the client endpoint IP address when it changes, but since both (a) many of the locations will be behind NAT devices over which I have no control, and (b) the option over which I do have control is an AT&T Unite hotspot which does not offer protocol 41 forwarding or respond to ICMP on its public address, this approach does not seem viable. I am additionally constrained as the mobile tablet(s) in question are Surface RTs, and as such are incapable of running, for example, AICCU client software. What is my best option to pursue to obtain IPv6 connectivity in this scenario?

    Read the article

  • DNS server not working?

    - by Behrooz A
    I just set up a DNS Server on my windows 7, called SimpleDNS I added a zone for example sag.com and defined www.sag.com and sag.com to 192.168.1.2 (my Network IP Address) . the problem is when I try to ping sag.com the SimpleDNS logs says that it answered the request with 192.168.1.2 , but the ping doesn't resolve anything . SimpleDNS logs: > 14:00:43 Request from 192.168.1.2 for A-record for www.sag.com > 14:00:43 Sending reply to 192.168.1.2 about A-record for > www.sag.com: 14:00:43 -> Answer: A-record for www.sag.com = > 192.168.1.2 14:00:43 -> Authority: NS-record for www.sag.com = mehr-pc nslookup : > C:\Users\Mehr\Desktop>nslookup www.sag.com DNS request timed out. > timeout was 2 seconds. Server: UnKnown Address: 192.168.1.1 > > DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. > *** Request to UnKnown timed-out the DNS server IP is 192.168.1.2 , and Access point address : 192.168.1.1 what should I do?

    Read the article

  • Returning a 404 page when a folder is accessed from one domain, but allowing access from other domains and IP addresses

    - by okw
    Situation: I want to return a 404 page ("404.php") when a folder ("hidden") is accessed from the example.com domain. I want the same folder to be accessible from a subdomain ("hidden.example.com") or from a different domain ("hidden.com") which are both configured in a single VirtualHost entry. The server has multiple IP addresses that it listens on. Each IP address serves identical content from the example.com domain (sharing a VirtualHost entry.) I want the folder to be accessible from the IP address. The server is configured to use SSL/TLS/HTTPS. HTTPS is optional on example.com, but HTTPS is enforced in the .htaccess file for the hidden folder using a rewrite rule shown below. /www/hidden/.htaccess RewriteCond %{HTTPS} !=on RewriteRule .* https://%{SERVER_NAME}%{REQUEST_URI} [R,L] I know that {SERVER_ADDR} gives the server's IP address, but does it return the one that the client is requesting from? I'm also starting to think that something in the VirtualHosts file would be more appropriate. Any thoughts on this? What should be allowed: http://87.65.43.21/hidden/ https://87.65.43.21/hidden/ http://12.34.56.78/hidden/ https://12.34.56.78/hidden/ http://hidden.example.com/ https://hidden.example.com/ http://hidden.com/ https://hidden.com/ http://www.hidden.com/ https://www.hidden.com/ What should be 404-ed with 404.php http://example.com/hidden/ https://example.com/hidden/ http://www.example.com/hidden/ https://www.example.com/hidden/ http://example.com/hidden/hiddenfile.php https://example.com/hidden/hiddenfile.php etc. Thanks.

    Read the article

  • DNS server not working?

    - by Behrooz A
    I just set up a DNS Server on my windows 7, called SimpleDNS I added a zone for example sag.com and defined www.sag.com and sag.com to 192.168.1.2 (my Network IP Address) . the problem is when I try to ping sag.com the SimpleDNS logs says that it answered the request with 192.168.1.2 , but the ping doesn't resolve anything . SimpleDNS logs: > 14:00:43 Request from 192.168.1.2 for A-record for www.sag.com > 14:00:43 Sending reply to 192.168.1.2 about A-record for > www.sag.com: 14:00:43 -> Answer: A-record for www.sag.com = > 192.168.1.2 14:00:43 -> Authority: NS-record for www.sag.com = mehr-pc nslookup : > C:\Users\Mehr\Desktop>nslookup www.sag.com DNS request timed out. > timeout was 2 seconds. Server: UnKnown Address: 192.168.1.1 > > DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. > *** Request to UnKnown timed-out the DNS server IP is 192.168.1.2 , and Access point address : 192.168.1.1 what should I do?

    Read the article

  • Opening port 80 in router has no results

    - by Ricardo Pieper
    A friend of mine has a ADSL modem and I need to forward some ports. I have already forwarded the 1521 port (Oracle) and it's working fine. Now I need to forward the port 80. I already set up his IIS bindings to this port, and also forwarded the port like this video shows: https://www.youtube.com/watch?v=DLKD-fyexoo So I think I did everything correctly. The local IP address is also the same as the machine where the IIS server is running. I'm sorry, but I can't post images since i don't have 10 points :( Somehow I can't forward this port, yougetsignal.com keeps saying that the door is closed. When I try to open the port, the Control Panel says me that I have to access the control panel in the 8080 port, because the 80 port will be open. Ok, that's fine. But I'm still able to access it in the 80 port, and when I try to access it in the 8080 port, it doesn't work. I'm trying it with the TPLINK 8816, but I also tried to open it in the Opticom DsLink 279, and it didn't worked (using another machine), I got the exact same results. He has a dynamic IP address, but he is also using No-ip, so I can always access his Oracle database in a certain static address. The 1521 port is open. I also tried to disable the firewall in Windows, but that makes no sense to me, since the router doesn't really open the port 80. Clearly I'm missing something. I have never done it in my life, so I dont know how to proceed. Restarting the router was the first I did, no results. I'm accessing his laptop through TeamViewer, so I'm testing the port outside his local network. Edit: My ISP says that they allow to open ports, and the 1521 port is opened. What could I do to open the 80 port?

    Read the article

  • Postfix relay gives error 450 while it should be 550

    - by dieter-be
    Hi, we use postfix to do relaying. We get several messages like the following in /var/log/mail (slightly edited) Apr 13 13:30:29 linserver postfix/smtpd[1064]: NOQUEUE: reject: RCPT from unknown[$ip]: 450 4.1.1 <[email protected]>: Recipient address rejected: undeliverable address: host domain.be [$ip] said: 550 <[email protected]>: Recipient address rejected: User unknown in virtual mailbox table (in reply to RCPT TO command); from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<BLUESTREAK.domain.local> Now, when the master mail servers gives a 550, claiming that the user does not exist, I want the relay to also give a 550 back. What happens now is that it seems to return a 450, causing clients to keep messages queued, keep trying and only notify users after a certain period has passed. According to what I could find, the soft_bounce could cause this. But we have not enabled this option (and by default it's off according to postfix docs) It might also have something to do with the *_reject_code postconf values. Especially since the log message complains the unknown ip. But as you can see in the postconf output below, smtpd_sender_restrictions and smtpd_client_restrictions are empty. So even if it would try to do any restrictions there, 550 is the "worst" error going on, so that's what I expect to be returned to the client. postconf: http://sprunge.us/JYgB Thanks, Dieter

    Read the article

  • DD-WRT (WRT54G) and (THOMSON TG782) how to put them togather?

    - by FeRtoll
    Ok so let me explain, i bought WRT54G and successfully installed DD-WRT v24-sp1 (07/26/08) mini-special - build 9994. That's all ok no problems with it all normal functioning. And just to add (i don't need wireless, wireless is turned off always) What i want: ISP's router (TG782) from it's INTERNET port(out) cable "which was before in my pc" is connected to WRT54G's INTERNET port and then from WRT54G LAN port 1 to my pc. The problem: How do i connect and setup all? I have tried many times on many different ways but cant get it to work IF THE CABLE FROM TG782 IS CONNECTED TO WRT54G ON INTERNET PORT. If i connect the TG782 to Lan port 1 on WRT54G and my pc to lan port 2 then all works fine after i setup gateway and all. But i want to connect TG782 to Internet port of WRT54G because i need "Access Restrictions" and this only goes through WAN right? please correct me if i am wrong. What i have tried: This is how i have tried to setup all. The TG782 router ip is 192.168.1.1 And WRT54G ip is 192.168.1.30 so in WRT54G control panel i have setup like this: ----WAN Connection Type---- Connection Type: Automatic Configuration - DHCP STP: Disabled ----Router IP---- Local IP Address: 192.168.1.30 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 (the TG782) ----Network Address Server Settings (DHCP)---- DHCP Type: DHCP Server Start IP Address: 192.168.1.100 Maximum DHCP Users: 6 And this wont work i probably miss something more, if anyone can help i would be thankfull. Also i have to note that i have tried to set my network adapter on pc to use the gateway of WRT54G and ip 192.168.1.102 In short: i cant get it to work normal only as a switch! Thanks for any help! -------EDIT:------- Here is an image which maybe can help: http://img27.imageshack.us/img27/4227/allin1w.jpg

    Read the article

  • grepping a substring from a grep result

    - by allentown
    Given a log file, I will usually do something like this: grep 'marker-1234' filter_log What is the difference in using '' or "" or nothing in the pattern? The above grep command will yield many thousands of lines; what I desire. Within those lines, There is usually one chunk of data I am after. Sometimes, I use awk to print out the fields I am after. In this case, the log format changes, I can't rely on position exclusively, not to mention, the actual logged data can push position forward. To make this understandable, lets say the log line contained an IP address, and that was all I was after, so I can later pipe it to sort and unique and get some tally counts. An example may be: 2010-04-08 some logged data, indetermineate chars - [marker-1234] (123.123.123.123) from: [email protected] to [email protected] [stat-xyz9876] The first grep command will give me many thousands of lines like the above, from there, I want to pipe it to something, probably sed, which can pull out a pattern within, and print only the pattern. For this example, using an the IP address would suffice. I tried. Is sed not able to understand [0-9]{1,3}. as a pattern? I had to [0-9][0-9][0-9]. which yielded strange results until the entire pattern created. This is not specific to an IP address, the pattern will change, but I can use that as a learning template. Thank you all.

    Read the article

  • Multiple Internet connections, multiple networks and split access in Linux

    - by Swapneel Patnekar
    I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

    Read the article

  • arp requests are sent continuously and my linux machine disconnected to the world

    - by sees
    I have the following problem and really need your help I'm implementing a small server to receive request from client on port 18999(just sample) using TCP socket. When I tested my server by using a lot of requests from a tablet through a router, I got the ARP problem(?) My net work just like: TABLET <------- WIRELESS ROUTER <------- MY SERVER (LINUX) Problems: 1. Can not connect to my Linux any more ( telnet, ping v.v...unreachable) 2. I use serial cable to connect to my Linux machine and use Wiresharp (from Windows) to catch the send message from Linux. It says that Linux keeps sending out continuously every 3 seconds ARP messages like the following: xx:xx:99:77:ff:69 ff:ff:ff:ff:ff:ff ARP 60 Who has 192.168.10.2? Tell 192.168.10.3 In the above message: xx:xx:99:77:ff:69 my Linux MAC address 192.168.10.2 my Tablet address 192.168.10.3 my Linux IP address Can you help me figure out the problem? Or tell me the way to detect the problem and reset the network back to normal (maybe restart Linux but I want to detect problem and restart automatically) UPDATE: 1. The above network works normally if tablet sends messages to my LINUX in normal speed (but also down after 48 hours) 2. The router works again after I unplugged my Linux ethernet cable (RJ45) from router. 3. The wireless network still works ( I can browser the router page from tablet) 4. When I use: ifconfig down then ifconfig up , the Linux restarts (?????????)

    Read the article

  • VMWare Guest Info - Wrong IP Returned

    - by Jon Bailey
    We're running a VDI environment with vSphere 4.0 and Oracle VDI 3.2.2 and are having a bit of a problem with users that connect to an IPSec VPN from within their VM. For some reason, once connected to the VPN, the VMWare API returns GuestInfo.ipAddress as the VPN IP rather than the primary IP of the only NIC on the system. The IP address shown in net[0].ipAddress is the correct address and is what vSphere client is reporting. Is there any way to get VMWare tools to report the net[0].ipAddress as GuestInfo.ipAddress? Below is sample output from the guestinfo.pl script. 172.16.1.2 is the example "bad" VPN address that our VDI software is seeing. VMXFLEX01 guestFamily: windowsGuest VMXFLEX01 guestFullName: Microsoft Windows XP Professional (32-bit) VMXFLEX01 guestId: winXPProGuest VMXFLEX01 guestState: running VMXFLEX01 hostName: VMXFLEX01 VMXFLEX01 ipAddress: 172.16.1.2 VMXFLEX01 toolsStatus: VMware Tools is running and the version is current. VMXFLEX01 toolsVersion: 8194 VMXFLEX01 Screen - Height: 600 VMXFLEX01 Screen - Width: 800 VMXFLEX01 Disk[0]: Capacity 42935926784 VMXFLEX01 Disk[0]: Path : C:\ VMXFLEX01 Disk[0]: freespace : 33272619008 VMXFLEX01 net[0] - connected : 1 VMXFLEX01 net[0] - deviceConfigId : 4000 VMXFLEX01 net[0] - macAddress : 00:50:56:95:1f:c9 VMXFLEX01 net[0] - network : VM Network VMXFLEX01 net[0] - ipAddress : 10.0.0.2

    Read the article

  • Fresh Proxmox VE 2.1 installation with defaults can't be reached or pinged

    - by Damainman
    I am using the lastest Proxmox VE 2.1. My server has two NICS with a uplink only connected into eth0. My Server is a co-located server utilizing public IPv4 IPs. It is not behind a firewall or any system which monitors traffic. Via IPKVM I did a fresh install of Proxmox, I put in the correct IP, Mask, Gateway, and DNS information. The install went perfectly fine with no errors. Upon completion and rebooting the system: I am unable to reach the web GUI via the browser, it just times out. I am unable to ping the server. I am unable to ping outside to the Internet from within the server. Tried pinging out to 4.2.2.2 and yahoo.com I tried rebooting the server and restarting the network service. IFCONFIG shows my IP information under vmbro0 which also has the same MAC address as the eth0 device. eth0 only displays a IPv6 Scope:Link address, which I did not setup myself. This is my first time installing proxmox, but after searching for a few hours it doesn't seem like anyone else is having the same issue as me from a fresh install with just the defaults. So far the only thing I did was install it. Also, I know the network cable is good and the IP is good because I was running a Xen XCP server with the same network settings prior to wiping it to install proxmox. Some additional information: for pveversion -v (Installed proxmox-ve_2.1-f9b0f63a-26.iso) pve-manager: 2.1-1 (pve-manager/2.1/f9b0f63a) running kernel: 2.6.32-11-pve proxmox-ve-2.6.32: 2.0-66 netstat -nr (note: .136 is my network, and .137 is my gateway) Destination - Gateway - Genmask xxx.xxx.xxx.136 - 0.0.0.0 - 255.255.255.248 0.0.0.0 - xxx.xxx.xxx.137 - 0.0.0.0 /etc/network/interfaces auto lo iface lo inet loopback auto vmbr0 iface vmbr0 inet static address xxx.xxx.xxx.138 netmask 255.255.255.248 gateway xxx.xxx.xxx.137 bridge_ports eth0 bridge_stp off bridge_fd 0

    Read the article

  • APACHE - PHP - Bounce emails

    - by user1179459
    I want to improve our mail server lists by handling all the bounces we get in our websites. I have a website which has over 8000+ users and another website which as over 1500+ users, they are emailed various notifications every second, ie. job alerts, email alerts, I am using POP connections with EXIM on APACHE server, most scripts are based on PHP language generates email on the fly. Problems i have But some users has registered long time ago and now quite few has bounce email address Some users register with dummy emails like [email protected] which never existed but a valid email address, any chance of stopping this without asking them login to the email account and clicking links which dont work most times.. (too annoying to the end user) Server is sending unnecessary emails can be avoided if i know they dont exists ? Solutions i need to have Is there a way i can download the bounce email list somewhere (WHM/Cpanel), i know exim mail has it but its not readable (i need a file like CSV or something similar to scan them over and write a php script to delete the users from the database ?) I need to know if there is any function in the PHP that can check the existence of the email address on the fly ? so that i can set the email send function in the mailer class to check before it sends out. On the server will bouncing emails are going to eatup lots of server resources ? like memory/cpu on processing them ? or are they are minimal where we dont have to worry about this at all ? May be a opensoruce or linux software to capture them and view them in a report basis and cleaning them up ? I am not a linux expert or server admin but i do lot of PHP coding, so please be descriptive of the solutions specially if they are linux commands Thank you!

    Read the article

  • How to run a website domain without redirecting if IP is already used for another website? [duplicate]

    - by SSpoke
    This question already has an answer here: Hosting multiple distinct folders for distinct domains 1 answer I bought a VPS Host that gave me only 1 IP Address which I used on my first domain name and it works without any problems. Now my second domain name I can't use the same ip address as it points to the first domain name. So I figured my only option was to use a GoDaddy hosted iframe redirection which redirects to a sub folder on my first domain which worked so far. Now I'm trying to load paypal from <?php headers() ?> and I get a permission error because of that iframe Refused to display 'https://www.paypal.com/cgi-bin/webscr?notify_url=&cmd=_cart&upload=1&business=removed&address_override=1' in a frame because it set 'X-Frame-Options' to 'SAMEORIGIN'. How do I avoid the Iframe solution for my second domain while not messing up my first domain? Somebody I forgot once told me it doesn't matter if you have 1 IP Address you could host multiple websites on it? how it that possible the DNS doesn't seem to work off ports afaik, yes I could host multiple websites on different folders but that's not what I call hosting a real website it has to be pointed by a domain name, so this iframe issue doesn't happen My server configuration is httpd (apache) that comes with CentOS 6 (Linux) operating system

    Read the article

  • debian VM refusing all traffic apart from http

    - by james lewis
    I've got a VM with a fresh install of Debian (wheezy) and I've installed node and mongo on it. The VM is using a bridged network connection so I was expecting to be able to point my host machines browser at the ip address of the Debian VM (port 1337 for my node example or port 28017 for my mongo status page) and see one of the two services (node or mongo). My requests are refused though. As far as I can tell Debian allows all traffic by default and you have to manually configure iptables to drop traffic. I've checked iptables and it says it's setup to allow anything through. It looks like this: root@devbox:/home/jlewis# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination As a test I setup nginx and I was able to get to the nginx landing page from my host no problems so obviously http traffic is allowed. I then set nginx up to forward all traffic upstream to mongo - no problems there, I was able to see the status page. I then did the same for my example node server and again, no problems. So http traffic is fine, but all other traffic is blocked. Anyone know why debian might be refusing all other traffic other than iptables being setup to drop it? EDIT - output from netstat -nltp: Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:28017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:51028 0.0.0.0:* LISTEN 1541/rpc.statd tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 2462/sshd tcp 0 0 127.0.0.1:1337 0.0.0.0:* LISTEN 2794/node tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 2274/exim4 tcp 0 0 127.0.0.1:27017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 1510/rpcbind tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 2189/nginx tcp6 0 0 :::22 :::* LISTEN 2462/sshd tcp6 0 0 :::45335 :::* LISTEN 1541/rpc.statd tcp6 0 0 ::1:25 :::* LISTEN 2274/exim4 tcp6 0 0 :::111 :::* LISTEN 1510/rpcbind

    Read the article

  • How do I resolve certificate errors on HP blade center

    - by Martin Hilton
    I'm trying to sort out the ssl certificate errors that we get when trying to manage our HP c7000 blade enclosures. To that end I have created a signing certificate and imported it into the browser. In Onboard Administrator I created a certificate signing request, which I signed with my CA and then uploaded the certificate. This worked perfectly, and I no longer get any SSL errors when connection to Onboard Administrator. The problem comes when trying to connect through Onboard Administrator to the iLo on the blades themselves. Done by clicking on the "Web Administration" link. Onboard Administrator links to the blade with it's IP address rather than host name. But the certificate signing request that iLo creates uses the host name. Even when this certificate is signed the browser still complains it is for the wrong domain. I either need to be able to get Onboard Administrator to connect to the blades using host name rather than IP address, or get a certificate signing request which contains the IP address as the CN rather than the host name. It doesn't particularly matter which. Does anybody know how to configure this?

    Read the article

  • Apache: How to redirect OPTIONS request with .htaccess?

    - by Milan Babuškov
    I have Apache 2.2.4 server with a lot of messages like this in the access_log: ::1 - - [15/May/2010:19:55:01 +0200] "OPTIONS * HTTP/1.0" 400 543 ::1 - - [15/May/2010:20:22:17 +0200] "OPTIONS * HTTP/1.0" 400 543 ::1 - - [15/May/2010:20:24:58 +0200] "OPTIONS * HTTP/1.0" 400 543 ::1 - - [15/May/2010:20:25:55 +0200] "OPTIONS * HTTP/1.0" 400 543 ::1 - - [15/May/2010:20:27:14 +0200] "OPTIONS * HTTP/1.0" 400 543 These are the "internal dummy connections" as explained on this page: http://wiki.apache.org/httpd/InternalDummyConnection The page also hits my main problem: "In 2.2.6 and earlier, in certain configurations, these requests may hit a heavy-weight dynamic web page and cause unnecessary load on the server. You can avoid this by using mod_rewrite to respond with a redirect when accessed with that specific User-Agent or IP address." Well, obviously I cannot use UserAgent because I minimized the server signature, but I could use IP address. However, I don't have a clue what should the RewriteCond and RewriteRule look for IPv6 address ::1. The website where this runs is using CodeIgniter, so there is already the following .htaccess in place, I just need to add to it: RewriteEngine on RewriteCond %{REQUEST_URI} ^/system.* RewriteRule ^(.*)$ /index.php?/$1 [G] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ /index.php?/$1 [L] Any idea how to write this .htaccess rule?

    Read the article

  • windows clients cannot get dns resolution until you open and close ipv4 properties page

    - by GC78
    This strange problem has started recently. Some windows clients cannot seem to get dns resolution to the internet after boot, and sometimes again at some point in the day. Internal hosts are also slow to resolve. trying to ping an interal host by name will take a long time for the hostname to resolve to ip address and trying to ping a website by name will fail to resolve. If you go into the tcp/ip v4 properties and view but not change anything, ok/close out of that then the client starts working fine, hostnames will resolve quickly. I have seen this happen on both Vista and W7 clients. ipconfig /all at a client experiencing this problem shows everything in order. proper ip addr, gateway, dns server, dns suffix ect.. ipconfig /dnsflush will not fix them, neither will /release and /renew the clients get their ip address, mask and dns server info from either one of 2 OES dhcp servers that assign addresses in different scopes in the same subnet. the internal dns server is a different OES dns server the default gateway is not assigned by the OES server but is statically put in at the client (only for those who need to get to the Internet for their job) flat network topology What can I do to get to the bottom of this? It only happens to a few of the client machines and typically the same ones. It started happening when we made a change to one of the DHCP scopes in iManager. Strangly this problem only happens to clients that get an IP address from the scope that we didn't make any changes to.

    Read the article

< Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >