Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 159/370 | < Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >

  • How to reliably keep an SSH tunnel open?

    - by Peltier
    I use an SSH tunnel from work to go around various idotic firewalls (it's ok with my boss :)). The problem is, after a while the ssh connection usually hangs, and the tunnel is broken. If I could at least monitor the tunnel automatically, I could restart the tunnel when it hangs, but I haven't even figured a way of doing that. Bonus points for the one who can tell me how to prevent my ssh connection from hanging, of course!

    Read the article

  • How to connect 2 routers (Asmax and D-link)

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • VLAN for WiFi traffic separation (new to VLANing)

    - by Philip
    I run a school network with switches in different departments. All is routed through to a central switch to access the servers. I would like to install WiFi access points in the different departments and have this routed through the firewall (an Untangle box that can captive-portal the traffic, to provide authentication) before it gets onto the LAN or to the Internet. I know that the ports that the APs connect to on the relevant switches need to be set to a different VLAN. My question is how do I configure these ports. Which are tagged? Which are untagged? I obviously don't want to interrupt normal network traffic. Am I correct in saying: The majority of the ports should be UNTAGGED VLAN 1? Those that have WiFi APs attached should be UNTAGGED VLAN 2 (only) The uplinks to the central switch should be TAGGED VLAN 1 and TAGGED VLAN 2 The central switch's incoming ports from the outlying switches should also be TAGGED VLAN 1 and TAGGED VLAN 2 There will be two links to the firewall (each on its own NIC), one UNTAGGED VLAN 1 (for normal internet access traffic) and one UNTAGGED VLAN 2 (for captive portal authentication). This does mean that all wireless traffic will be routed over a single NIC which will also up the workload for the firewall. At this stage, I'm not concerned about that load.

    Read the article

  • "Play on another device" function not working with Samsung Allshare

    - by Tural Teyyuboglu
    Briefly I can't get work "Play on another device" function More detailed My Samsung TV (which support network) and PC are in the same network. The problem is, I can play PC contents from TV. But when I try to control TV remotely from Allshare software (PC), it shows TV only as connected device: But not as remote player in "players" list The result Tried to turn off firewall completely, reset router, re-install software. No success. Please help. BTW. On this link they kinda explained how to do it, but I software doesn' detect the TV as player in my case: http://www.samsung.com/global/allshare/pcsw/quickguide.html

    Read the article

  • TTL and traceroute showing different values for same domain

    - by Cray XT3
    y am i getting two different output for tracert and ping. Ping Result showing total hops of 20 and tracert showing 8. default ttl value on my linux machine 64,icmp echo reply ttl value 44. 64-44=20 but tracert is showing only 8 hops. What can be the reason? If tracert is implemented using ttl then why am i getting different values for same domain.no matter how many times i tried. Fo google and google services,ttl value and tracrt are same,but for other domains its different.

    Read the article

  • apache returning "The connection was reset"

    - by usjes
    One of my dedicated servers had some network issue today and the data center has to replace some router. Since then the sites on that server returns "The connection was reset" error most of the time. I tried installing nginx and it opens better, but it still shows the error sometimes. Everything in the config seems normal, what could be causing this error? UPDATE: Just noticed that in whm apache status there are always only 1 requests currently being processed, 8 idle workers. I know for sure the server received thousands of requests per minute. What could be limiting this to such a low number?

    Read the article

  • What is automatic service location on the network?

    - by Roman
    I know that zeroconf does automatic service location on the local network. But what does it mean? For example there is a printer (printing is the service that it does). This printer choose randomly an IP for itself. It asks other devices if this IP is already occupied. If not, the printer occupies this IP. Then printer says to "everybody" that "printing" service is associated with this IP. Is it "automatic service location"? Or I got something wrong?

    Read the article

  • IRC server connecting to another server

    - by Oxinabox
    I'm setting up an IRC server using IRC-Hybrid, I want my server to connect to another server, so that people on my server can connect to channels on that other server. I know this can be done, the GIMP IRC, is the same as the GNOME IRC My ircd.conf contains the following: connect { name = "aabstractname"; host = "128.64.2.1; send_password = "somepass"; accept_password = "somepass"; encrypted = no; port = 6667; class = "server"; autoconn = yes; compressed = yes; fakename = "irc.sd.dom.asn.au"; }; So when i run: /etc/init.d/ircd-hybrid restart it should be connecting to 128.64.2.1, but the log on 128.64.2.1, doesn't show anything Do I need entry on the host 128.64.2.1? I can't find any documentation for ircd.conf I'ld really like that documentation so I can check all my settings are right.

    Read the article

  • Tunneling a public IP to a remote machine

    - by Jim Paris
    I have a Linux server A with a block of 5 public IP addresses, 8.8.8.122/29. Currently, 8.8.8.122 is assigned to eth0, and 8.8.8.123 is assigned to eth0:1. I have another Linux machine B in a remote location, behind NAT. I would like to set up an tunnel between the two so that B can use the IP address 8.8.8.123 as its primary IP address. OpenVPN is probably the answer, but I can't quite figure out how to set things up (topology subnet or topology p2p might be appropriate. Or should I be using Ethernet bridging?). Security and encryption is not a big concern at this point, so GRE would be fine too -- machine B will be coming from a known IP address and can be authenticated based on that. How can I do this? Can anyone suggest an OpenVPN config, or some other approach, that could work in this situation? Ideally, it would also be able to handle multiple clients (e.g. share all four of spare IPs with other machines), without letting those clients use IPs to which they are not entitled.

    Read the article

  • to measure throughput of testing device connect to server via AP

    - by samantha
    Description of project- I have a test tool to which DUT connects. The test tool has an access point in it and once DUT get connected to it via mac address we check RSSI and some other features of WiFi of DUT. Now I am wondering is there is any way I can measure throughput of Device under test via mac address of DUT from server side. Test-tool has LINUX fedora 11 in it and major coding is done in c/C++ and json command. Previously, I have tried to install ftp server on test-tool and DUT can connect to it and we can measure the throughput or data transfer rate, but this is not feasible solution as it requires lot of intervention from DUT. What I am interested in is 1) To run some script on server side /test tool and it gives me throughput of bandwidth of connected device may be via mac address of DUT OR 2) Server script transfer some files/packets to DUT and we can measure the throughput. Coding is not a major challenge at this stage , I just need some tool which requires minimum intervention from DUT.

    Read the article

  • Erratic WiFi 2.4 GHz channel spikes, what gives?

    - by Francis W. Usher
    Sorry guys, first a gripe about my neighbor's WiFi access point (it is related): they totally hog the center nine 2.4 GHz channels (3-11), centered right at 7! I know the outer regions of the signal don't make as much of a difference, and technically they're running channels 5 & 9. Anyway, their signal is clearly interfering with mine, which is necessarily centered at 3 or 11 to evade their interference. I guess it's somewhat a case of access point envy: they happen to have both a stronger signal and a higher data rate, while occupying twice the band width that I do. Getting to the point, I've noticed that they tend to sit nice and pretty centered at 7, but they definitely auto-select their channel, and I've noticed that the auto-selection algorithm tends to shift towards the higher channels; hence I decided to pick channel 3, and I don't get so many intermittent lag spikes any more. Anyway, the thing that weirded me out was the reason they have to auto-select sometimes: unexplained, powerful (talking order of 0dB here), giant spikes of 2.4 GHz activity in consistent regions of the spectrum. I don't think it's just noise, since my wireless monitoring software is registering a MAC address, a manufacturer, and usually a fairly coherent ascii name... and it seems to be a fairly well-confined signal. But these signals are fairly common, and they do some weird stuff to my signal. So my question is what are these signals? Where are they coming from? Where are they going? Why are they so ridiculously strong? Why don't they ever last very long? Here's an inSSIDer screenshot I took, for your perusal. I am labeled with "me", my greedy neighbor labeled with "neighbor", and the 2 quasar signals are labeled with "WTF?".

    Read the article

  • error: "net.netfilter.nf_conntrack_acct" is an unknown key

    - by anonymous
    Hello, i have the next error when i run 'sysctl -p' error: "net.netfilter.nf_conntrack_acct" is an unknown key net.netfilter.nf_conntrack_acct = 1 net.ipv4.netfilter.ip_conntrack_max = 9527600 net.ipv4.netfilter.ip_conntrack_tcp_timeout_established = 7200 lsmod ipv6 289352 34 loop 19724 0 nf_conntrack_ipv4 19352 0 nf_conntrack 71440 1 nf_conntrack_ipv4 joydev 15232 0 evdev 14592 0 ext3 125456 3 jbd 54696 1 ext3 mbcache 13188 1 ext3 raid1 24832 4 md_mod 81700 5 raid1 thermal_sys 17728 0 Debian 5.0.8 Any idea? Thanks

    Read the article

  • Presentation software requires admin rights to install - any way to remove this requirement?

    - by James F
    I have some wireless presentation software which I use in a meeting room in order to allow end users to hold presentations here and wirelessly have their laptop screens showing on the TV on the wall. Unfortunately the .exe file requires admin rights to install therefore requiring that either the user requests temporary admin rights beforehand, I install it using my admin account or that we use a VGA/HDMI cable. Is there a way to remove the admin right requirement from a .exe or a .msi file so that it can be installed freely by any user? We are using XP for now but will be moving to 7 soon. Thanks James

    Read the article

  • Find computer names on a private network (with nmap?)

    - by paracaudex
    On a LAN, I want to find out the names of all the connected computers using a cross-platform program, preferably nmap. I know I can do nmap -sn xxx.xxx.xxx.xxx/24 (where xxx.xxx.xxx.xxx is a local IP address) to find hosts which are up, but how do I find the computers' hostnames? Do they broadcast this in a way that I can find using nmap? UPDATE: It looks like Angry IP Scanner can do this. How does it do this? Can I replicate it with nmap?

    Read the article

  • Mounting any Windows share from OS X 10.7.5 suddenly stopped working

    - by user2169619
    I have problem with mounting Windows network shares from my OS X 10.7.5 - it worked but it stopped and nothing helps and nothing in logs. Here what I get when trying to mount it manually: mount -t smbfs //10.0.0.7/d /tmp/test When doing sniffing with tshark - no packet it sent through and I get immediately return from the command: mount_smbfs: server connection failed: Unknown error: -1 Nothing in /var/log/syslog.log and /var/log/kern.log. The Finder does not work either - it throws an error that something is wrong (in czech thus I'm not sending the message here). I just cannot connect to any network shares. In virtual Windows 7 in Parallels Desktop I can connect successfully, but not within the network share (so the Win7 is behind OS X NAT) but only with its own IP address. The Windows server share is on the same network segment connected through switch. Any advice how to debug and what can be wrong? I spent hours to find solution on Google and here but no-one with this kind of problem and I do not know how to further debug it since there is no meaningful log / trace etc. I can ping 10.0.0.7 and I can connect to FTP server on 10.0.0.7 - the Windows machine (XP) has firewall completely turned off. The problem is that with tshark, I'm not seeing any packet sending to 10.0.0.7 so it's not even trying to reach the server.

    Read the article

  • How do I get the IP Adress of my vpn server

    - by kashif
    I Connect to internet using PPTP connection type from my computer using following setting internet address: blue.connect.net.pk user id: myusername password: mypassword my problem: my dwr-112 router doesn't support internet address name, it rather supports only ip address of the server i.e I'm not able to type blue.connect.net.pk as it only supports server's ip adress. my question: How can I know the ip address of vpn server so that I can configure my dwr-112 router to connect to internet using pptp connection type

    Read the article

  • Barriers to IPv6 deployment: addressing

    - by sysadmin1138
    There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

    Read the article

  • Mac OS X 10.6.5 and link-local addresses (169.254.x.x)

    - by WMR
    Starting with the latest update of Mac OS X (10.6.5) all Apple applications (Safari, Mail, iChat, etc.) don't connect to the internet anymore, if the assigned IP address is from the 169.254.0.0./16 range. This is not a routing problem, I can still ping any server I want, even connecting via command line tools works. I know this problem could easily be fixed by changing the IP address to a more common RFC1918 address (e.g. 192.168.0.0./16), but this is what the ISP assigns via DHCP and I am not sure I can convince them (Xplornet) to change that. So I am wondering if there's a (hidden?) setting that would convince Apple applications, that they are in fact still online.

    Read the article

  • Postfix as mail relay for web servers?

    - by Ben Carleton
    Hi all, I want to set up Postfix to relay mail from a group of webservers. I would like to limit senders by IP so I can restrict the box to only my webservers, so I don't have an open relay and don't have to worry about authentication. So, what I guess I need is to limit inbound access but allow mail to be sent to any outbound address. I've looked through the docs and don't even know where to start, so any tips would be appreciated. Thanks!

    Read the article

  • Connecting to same public IP from different locations yields different results

    - by DHall
    Since yesterday I've been unable to access one of my favorite time-wasting sites, boston.com. It starts to load but then it gets redirected to pagesinxt or something like that. After some investigation, I've narrowed it down to an issue with cache.boston.com, but only from my work location. I found the IP (216.38.160.107) , but even that doesn't work correctly from here at work. When I do a telnet 216.38.160.107 80 GET http://cache.boston.com/universal/css/hp_bgcom.css from another location, I get a nice long CSS, as expected. From here, I get an error (trimmed for size): HTTP/1.1 400 Bad Request Your request could not be processed. Request could not be handled This could be caused by a misconfiguration, or possibly a malformed request. For assistance, contact your network support team. Is there any way I can troubleshoot this further on my end? Tracert doesn't tell me anything too useful: Tracing route to vwrpx1.ttn.xpc-mii.net [216.38.160.107] over a maximum of 30 hops: 1 * * * Request timed out. Since it's not really work-related, I don't really want to bring it up to our network team unless I know what's going on, or if there's some risk to the network (ex. malware or something)

    Read the article

  • Slowdown upon router/modem setup change

    - by Ollie Saunders
    I’ve been using a Belkin FSD7632-4 modem router to connect to my TalkTalk provided ADSL internet connection for some time and been pretty happy with it. Recently, however, the connection has been failing and I decided to get a ASUS RT-N16 instead, which is also a much more capable router generally. The ASUS RT-N16 doesn’t come with a modem built-in so I purchased as Zoom modem as well. I’ve set them both up and am using them to post this message. But I’m a bit miffed to find that I get a significantly and consistently slower downstream rate from the new configuration than with the old Belkin. Belkin modem router: downstream: 3.45 mbps upstream: 0.73 mbps ASUS router + Zoom modem: downstream: 2.71 mbps upstream: 0.66 mbps Any ideas why this is? The really weird thing about this is that the Zoom supports ADSL2 and ADSL2+ but I don’t think the old Belkin does. At first I thought it might be due to the Zoom modem being limited to PPPoE instead of PPPoA, which my ISP supports, but then I tried using PPPoE with the Belkin and that still gave a high speed. I’m using VC-Mux encapsulation with both. VPI of 0 and VCI of 38. I pulled this data off the Zoom: Mode: ADSL2 Line Coding: Trellis On Status: No Defect Link Power State: L0 Downstream Upstream SNR Margin (dB): 12.3 11.8 Attenuation (dB): 43.0 24.9 Output Power (dBm): 12.9 0.0 Attainable Rate (Kbps): 3936 844 Rate (Kbps): 3194 840 MSGc (number of bytes in overhead channel message): 59 10 B (number of bytes in Mux Data Frame): 99 14 M (number of Mux Data Frames in FEC Data Frame): 2 16 T (Mux Data Frames over sync bytes): 1 8 R (number of check bytes in FEC Data Frame): 8 8 S (ratio of FEC over PMD Data Frame length): 1.9833 9.0594 L (number of bits in PMD Data Frame): 839 219 D (interleaver depth): 32 2 Delay (msec): 15 4 Super Frames: 15808 14078 Super Frame Errors: 0 4294967232 RS Words: 513778 111753 RS Correctable Errors: 126 4294967238 RS Uncorrectable Errors: 0 N/A HEC Errors: 0 4294967279 OCD Errors: 0 0 LCD Errors: 0 0 Total Cells: 1920175 237597 Data Cells: 205993 392 Bit Errors: 0 0 Total ES: 0 0 Total SES: 0 0 Total UAS: 34 0

    Read the article

  • Is it better to use N WiFi or Cat5e ethernet for large file transfers?

    - by Seth
    I have a network containing 802.11 N WiFi Devices and gigabit ethernet devices, however using only Cat5e wiring. I know that if I used Cat6, the ethernet would be much faster however if I need to transfer a large file between a device thats connected normally connected via ethernet and a device thats normally connected via WiFi, would it be advantageous to bother plugging the WiFi device in to the network? or should I switch the ethernet device to WiFi? or does it really matter?

    Read the article

< Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >