Search Results

Search found 587 results on 24 pages for '802 1q'.

Page 16/24 | < Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >

• Yoga Pro 2 Wi-Fi not working

  - by user293004

  I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

  Read the article

• b43 module loaded, but no interface showed up

  - by Eduardo Bezerra

  I'm using CentOS 6.3 x86_64 on a hardware with a BCM43224 chip for wi-fi. I installed the b43-fwcutter module and then run modprobe b43, with no error messages. However, no new network interface showed up, and the return of iwconfig is: lo no wireless extensions. eth0 no wireless extensions. lspci -nn | grep 43224 returns: 03:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) and uname -a: Linux localhost.localdomain 2.6.32-279.14.1.el6.x86_64 #1 SMP Tue Nov 6 23:43:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Any ideas of how to make the wireless device work?

  Read the article

• Can't connect to or see my wifi ssid

  - by ant

  Today I installed ubuntu 12.04 on my laptop. I am unable to see my home SSID or even connect to it. I've tried to connect as a hidden SSID but I always get prompted for authorization although my key is correct. I'm in in Europe but my laptop is from US. I'm not sure if that is relevant. I've read around this site and saw something that has to do with setting the channel above 11. I'm not sure I did that correctly I did this : How to use Wi-Fi channels above 11? Did't help. I'm able to connect with cable but not via wifi either windows or linux. Other devices in my home can connect without any issues, even the kindle. Here is the screenshot from my router : Here is some additional info : lspci | grep -i network 08:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) lspci -nnk | grep -A2 0280 08:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) Subsystem: Hewlett-Packard Company U98Z062.10 802.11bgn Wireless Half-size Mini PCIe Card [103c:303f] Kernel driver in use: ath9k m-tool NetworkManager Tool State: connected (global) Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: disconnected Default: no HW Address: 90:4C:E5:38:79:0D Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes I'm not sure what to do next. Any suggestions?

  Read the article

• Why is wireless slow with Atheros AR9285?

  - by Luke

  I know there are many posts like this, however none of the fixes I have found have worked. I had the issue on 11.04, and after having no luck fixing it decided to try 12.04 however this has not fixed the problem. I'm using a Lenovo IdeaPad, the network card is a Atheros Communications AR9285. edit add outputs: sudo iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"NETGEAR-PLOW" Mode:Managed Frequency:2.437 GHz Access Point: E0:91:F5:7D:1B:BA Bit Rate=65 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:77 Invalid misc:63 Missed beacon:0 eth0 no wireless extensions. lspci -nnk | grep -iA2 net 06:00.0 Network controller [0280]: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) Subsystem: Lenovo Device [17aa:30a1] Kernel driver in use: ath9k -- 07:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) Subsystem: Lenovo Device [17aa:392e] Kernel driver in use: r8169 Thanks

  Read the article

• My windows xp wireless hotspot wifi isn't working

  - by Dominic Grenier

  I add the hotspot the regular way. Yet it doesn't show up as available when I try to connect to it using my other Ubuntu laptop. And nothing can connect to it. Yesterday, I successfully made it work for 5 minutes and then it stopped without me changing any configuration. I've already tryed resetting the DNS. Edit: I've updated my Broadcom 802.11b/g driver to a generic but more recent version. I've also repaired the WMI, now the advanced tab of my primary connection is available and the hand meaning the connection is shared appeared. But the computers still connect the wrong way around. (Windows to ubuntu instead of ubuntu to windows) Reinstalled SP3...

  Read the article

• Blank screen after GRUB (64 bit) - cannot install Ubuntu

  - by peGGi

  My laptop's specs: Lenovo IdeaPad Z570 Intel Core i5-2410M @ 2.3Ghz 6 Gb RAM DDR3 640 Gb ATAPI Hard-disk Drive @ 5,200 RPM NVIDIA GeForce G520M with Optimus switching technology Broadcom 802.11n Network Adapter REALTEK soundcard Windows 7 Home Premium 64-bit I downloaded Ubuntu Studio 11.04 and burned the iso image onto two different DVDs, using two different programs (one DVD is RW, the other is just R). I verified the hash MD5sum thing. I get as far as GRUB with the 4 options (install, advanced install, disk verification, system rescue) but no matter which one I select, I get a blank screen and nothing happens. The DVD drive spins down after about 30 seconds. Also just before the GRUB screen I get a message saying Error: "Prefix" is not set. I'm not sure if that's relevant. I have tried all the options using both DVDs. Same thing happens. I have changed the graphics setting in BIOS to UMA or Optimus, but still happens either way. I've tried booting with the wireless switch turned off, same thing happens. I downloaded 'vanilla' Ubuntu 64-bit and burned onto a CD, and the same thing happens. I have downloaded Ubuntu 32-bit and I am able to boot from the live CD (interestingly the wireless card won't work, but that's maybe another issue). I have searched extensively through these forums and other sites but I can't see anything that will help me. Is there something I'm missing? I'd really appreciate help on this. The laptop is less than 2 weeks old. I was so looking forward to getting Ubuntu Studio up and running. I've gone about as far as my technical abilities will allow.

  Read the article

• How to get my laptop to detect SD cards inserted into its built-in card reader?

  - by Candelight

  My laptop has a built-in SD Card reader but it cannot detect one when inserted. Here is the result when I type lspci from the terminal: 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 10) 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:06.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:12.0 IDE interface: ATI Technologies Inc IXP SB400 Serial ATA Controller (rev 80) 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (rev 80) 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 83) 00:14.1 IDE interface: ATI Technologies Inc IXP SB400 IDE Controller (rev 80) 00:14.2 Audio device: ATI Technologies Inc IXP SB4x0 High Definition Audio Controller (rev 01) 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80) 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS482 [Radeon Xpress 200M] 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 05:04.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 05:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 05:04.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 05:09.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g

  Read the article

• How do I install the EW-7318Ug wireless drivers?

  - by user69731

  I'm on Ubuntu 12.04 and I need to install & configure Internet connection. I want to use montor mode in Wireshark. After Ubuntu installation my wireless card was recognized but it doesn't connect to the Internet. Internal wireless card works well. What should I do? I'm new to Linux. PC:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 64:31:50:0f:d4:70 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x8000 eth1 Link encap:Ethernet HWaddr e0:2a:82:aa:2d:3e inet addr:192.168.0.101 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::e22a:82ff:feaa:2d3e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20978 errors:0 dropped:0 overruns:0 frame:364651 TX packets:20949 errors:171 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19299119 (19.2 MB) TX bytes:3024858 (3.0 MB) Interrupt:19 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4788 errors:0 dropped:0 overruns:0 frame:0 TX packets:4788 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:387017 (387.0 KB) TX bytes:387017 (387.0 KB) wlan1 Link encap:Ethernet HWaddr 00:1f:1f:44:c1:a4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10508 errors:0 dropped:0 overruns:0 frame:0 TX packets:6143 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14831319 (14.8 MB) TX bytes:644606 (644.6 KB) PC:~$ iwconfig lo no wireless extensions. wlan1 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:225 Noise level:162 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions.

  Read the article

• multiple vlans routed on one nic? trunk?General? or Access?

  - by Aceth

  ok for the last week I've tried racking my head around this... I have a SRW208P with 802.1q support, and a virtual endian appliance. I would like to be able to have 3 vlans having everything routed through the endian appliance.. i.e. The Virtual server has 2 bridged NIC's to the switch. This is where I'm getting confused .. On the 8 port switch I've got the 3 vlans set up ok (all being untagged as they are not going to be vlan aware), it's the port I'm connecting the endian firewall to the switch I'm having trouble with (second nic goes to the adsl modem and NAT'd) Is it meant to be a trunk, "Genereal" or "Access" then untagged or tagged? the end goal is to have vlan traffic routing through the single NIC and have endian route vlan traffic according to the rules. Any one have any ideas on the cisco small business stuff? Thanks

  Read the article

• Can't install Ubuntu, black screen after install

  - by Tyrone

  I tried several times, but wasn't able to make it work. I tried all recent types of Ubuntu but it didn't work. Then I tried acpi=off at the beginning of the installation. In this way I could finish the installation. But after the restart Ubuntu didn't work. Only a black screen appeared. Before that I tried it on the VirtualBox and it work. By the way my system is the following: (I use windows 7 currently) Processor AMD Athlon II P320 (2,1 GHz, second-level cache 2 ? 512 KB, HT 1600 MHz bus) Chipset AMD M880G + SB850 Memory Dual Channel, 3 GB DDR3-1066 Wide Screen 15.6 “high-definition (1366 ? 768) c LED-backlit, AU Optronics B156XW02 Video Card AMD Radeon HD 4250, from 336 MB video buffer in memory, support for DirectX 10.1 and UVD Sound system: HDA-codec IDT 92HD81B1X AMD HDMI Audio Hard drive WDC WD3200BEVT-75A23T0 (298 GB, 5400 RPM, SATA 2.0) Optical Drive: DVD ± RW Optiarc AD-7585H Communication tools Fast Ethernet (10/100 Mbit / c) Realtek RTL8102E/RTL8103E WiFi 802.11a/b/g Broadcom BCM4310 Bluetooth 2.1 + EDR Card reader Memory Card Reader 7-in-1 with support for SD / SDHC / MMC / MS / xD, and derivatives Interfaces / ports 3 USB 2.0 1 eSATA + USB 2.0 15-pin video connector VGA HDMI RJ-45 Ethernet 10/100 Mbit / c 2 analog mini-jack: a microphone / headphone jack for a Kensington lock slot AC adapter Battery Li-Ion 6-cell capacity of 4400 mA ? h (10,8, 48 W ? hr) AC power adapter 65 Watt Additional equipment integrated web-camera (1.3 mega pixels)

  Read the article

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• My windows xp wireless hotspot isn't working

  - by Dominic Grenier

  I add the hotspot the regular way. Yet it doesn't show up as available when I try to connect to it using my other Ubuntu laptop. And nothing can connect to it. Yesterday, I successfully made it work for 5 minutes and then it stopped without me changing any configuration. I've already tryed resetting the DNS. Edit: I've updated my Broadcom 802.11b/g driver to a generic but more recent version. I've also repaired the WMI, now the advanced tab of my primary connection is available and the hand meaning the connection is shared appeared. But the computers still connect the wrong way around. (Windows to ubuntu instead of ubuntu to windows) Reinstalled SP3...

  Read the article

• Help setting up wireless in Ubuntu 13.04

  - by James

  I'm having problems connecting my WIFI in Ubuntu 13.04 . So I was wondering if filling in the data manually ie: the IPv4, IPv6, the SSID and BSSID info etc. I did try this before but maybe I put in the wrong data or maybe not enough. Would that make it work? I just don't know how to find out some of the data you need to put in? I'm new and it's confusing. Does anyone know the solution? Here is lspci: james@james-MM061:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 01) 00:1c.3 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 01) 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] (rev 01) 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 01) 03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller 03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 03:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a) 03:01.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05) 0b:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) Computer information: Model: Dell MM061 Mobile Intel(R) 945GM Express Chipset Family [Display adapter] (2x)

  Read the article

• How can I set up VLANs in a way that won't put me at risk for VLAN hopping?

  - by hobodave

  We're planning to migrate our production network from a VLAN-less configuration to a tagged VLAN (802.1q) configuration. This diagram summarizes the planned configuration: One significant detail is that a large portion of these hosts will actually be VMs on a single bare-metal machine. In fact, the only physical machines will be DB01, DB02, the firewalls and the switches. All other machines will be virtualized on a single host. One concern that has been is that this approach is complicated (overcomplicated implied), and that the VLANs are only providing an illusion of security, because "VLAN hopping is easy". Is this a valid concern, given that multiple VLANs will be used for a single physical switch port due to virtualization? How would I setup my VLANs appropriately to prevent this risk? Also, I've heard that VMWare ESX has something called "virtual switches". Is this unique to the VMWare hypervisor? If not, is it available with KVM (my planned hypervisor of choice)?. How does that come into play?

  Read the article

• Apple Airport Extreme Wireless Card M8881 Connectivity Issue

  - by Carlosfocker

  I bought a Apple Airport Extreme Wireless Card M8881 with the antenna for my old Power Mac G5 1.6 Ghz. The computer is running OS X 10.4. The card works and I can connect to my dlink 802.11g wireless router using WPA2/AES encryption. The problem is that the connection has intermittent connectivity issues. When the issue occurs the signal bars for the connection drop to one or two bars and the performance of the connection suffers greatly. The computer isn't far from the wireless router. I have a laptop at the desk where the mac is and it does not have any issues. I'm not sure what it might be? Updated drivers? Firmware? Let me know if I forgot any important information.

  Read the article

• No Wireless In Ubuntu 13.10

  - by viktorhubinette

  When I upgraded to Ubuntu 13.10, I can't connect to wireless. The only thing I can connect to is ethernet, so please help me, What should I do? Here is the output of the lspci -nnk | grep -i net -A2 00:19.0 ethernet controller [0200]:intel corporation 82579V Gigabit network connection [8086:1503] (rev 04) subsystem: acer incorporated [ALI Device] [1025:8000] Kernel driver in use : e100e output of lsusb: Bus 002 Device 003: ID 046d:c31c Logitech, Inc. Keyboard K120 for Business Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:0152 Realtek Semiconductor Corp. Mass Storage Device Bus 001 Device 040: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 004: ID 0bda:8178 Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter Bus 003 Device 003: ID 045e:070f Microsoft Corp. Bus 003 Device 002: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• There's IP but can't reach gateway

  - by icky

  I have just installed ubuntu 12.04 on my new laptop, and brought it back to home, but I found the wireless network does not work. Strangely, it has the correct ip, but can't connect to the gateway. ifconfig gives ip 192.168.64.36, with broadcast 192.168.79.255 and mask 255.255.240.0, this are all correct, the gateway is at 192.168.64.1 cat /etc/resolv.conf nameserver 192.168.64.1 nameserver 127.0.0.1 which i think it's also right. but when I ping 192.168.64.1, all packages are lost. Please help me with this, I really do not know what happened to my network settings. Huckle, Thank you for your reply ifconfig wlan0 Link encap:Ethernet Hwaddr 88:f9:af:2a:ca:1b inet addr:192.168.64.36 Bcast:192.168.79.255 Mask:255.255.240.0 inet6 addr: fe80::8a9f:faff:fea2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3950 TX byetes:60288 iwconfig wlan0 IEEE 802.11bgn ESSID:"Chiono" Mode:Managed Frequency:2.417 GHz Access Point: 82:54:99:94:6D:43 Bit Rate=13.5 Mb/s Tx-Power=13 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=70/70 Signal Level=-32 dBm Rx invalid nwid:0 Rx invalid crypt:0 RX invalid frag:0 Tx excessive retries: 9 Invalid misc:10 Missed beacon:0 route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.64.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.64.0 * 255.255.240.0 U 2 0 0 0 wlan0 Thank you very much

  Read the article

• Windows 8.1 killed my wifi

  - by char1es

  Was running Windows 8 on a Lenovo G780 and updated to windows 8.1 Wifi does not work anymore, i always receive a dns server not responding error. I have tried using public dns servers from Google but with still no results. I've restarted my router with no results. All other devices on my network are having no trouble at all. I've tried updating the wireless driver but the manufacturers website claims that the Win8.1 driver should be updated with the update from windows. So i cant find a wireless driver... Anyone else having this error and does anyone have any ideas on how to fix it?? EDIT: here are the driver details: Broadcom 802.11n Network Adapter Provider: Microsoft Driver Date: 2013-05-31 Driver Version: 6.30.223.102 Digital Signer: Microsoft Windows Thanks

  Read the article

• USB Keyboard doesn't work in Ubuntu 14.04

  - by Steven Crossan

  My USB keyboard isn't working in Ubuntu 14.04, but also didn't work in 13.10. I upgraded today in the hope that the issue would be resolved, but it wasn't. The keyboard works in BIOS and GRUB but stops working when I reach the login screen. It is detected by the system, but just doesn't work. Output of lsusb: Bus 002 Device 002: ID 0846:9011 NetGear, Inc. WNDA3100v2 802.11abgn [Broadcom BCM4323] Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 002: ID 1532:000d Razer USA, Ltd Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 002: ID 060b:2231 Solid Year KSK-6001 UELX Keyboard Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub I added: hid usbhid hid_generic ohci_pci To /etc/initramfs-tools/modules and did update-initramfs -u, but that didn't work. I'm new to Ubuntu/Linux and any help you could provide would be greatly appreciated!

  Read the article

• Laptop's wifi router is not emitting signals therefore my PC and Nokia cell are not connecting to internet

  - by umer sanny

  I have a USB internet connection which I plugged into my laptop. I converted my laptop's Wifi into a Wifi router so that I can attach my PC and cell to this network and enjoy internet, but it doesn't work. I have a Dell Inspiron N5110 i7 Windows 7 64-bit laptop, Dell D865 PC and Nokia C5. My PC and cell are showing that there is a new Wifi connection available, but when I connect to it, it won't load any web page. Reason is my laptop's Wifi is not emitting any internet signals or may be some other issue which i dont know.. laptop's adapter is 802.11b/g/n I don't know why. How can I enjoy Wifi internet on laptop, PC and cell at the same time?

  Read the article

• Effect of using dedicated NVidia card instead of Intel HD4000

  - by Sman789

  Short version: Can someone please advise me of the effect of adding a dedicated NVIDIA GeForce GT 630M card to an Ubuntu laptop in terms of power consumption and performance gains/losses when doing general productivity tasks and booting up. Also, how good are the closed source, open source, and Bumblebee drivers for these newer cards compared to support for the Intel HD4000? Long version/Background, if any info here is helpful: I'm thinking of ordering a laptop from PC Specialist (a UK company who actually sell machines without Windows pre-installed) with the following specifications: Genesis IV: 15.6" AUO Matte 95% Gamut LED Widescreen (1920x1080) Intel® Core™i5 Dual Core Mobile Processor i5-3210M (2.50GHz) 3MB 4GB SAMSUNG 1600MHz SODIMM DDR3 MEMORY (1 x 4GB) 120GB INTEL® 520 SERIES SSD, SATA 6 Gb/s (upto 550MB/sR | 520MB/sW) Intel 2 Channel High Definition Audio + MIC/Headphone Jack GIGABIT LAN & WIRELESS INTEL® N135 802.11N (150Mbps) + BLUETOOTH Now, as I want this laptop mainly for work and not for games, I would be more than content with the HD4000 integrated chip which comes with the processor. However, for compatibility reasons, I am not able to get the specs I want unless I choose a NVIDIA GeForce GT 630M 1GB graphics card, which I don't have a great deal of use for. I'm willing to buy it, however, as it's still cheaper than any other laptop with the specs I want. However, I know that Linux power management isn't fantastic with open-source graphics drivers, and I don't much about Bumblebee. Basically, whilst I'm happy to 'tolerate' the card being there, I don't want to experience any negative effects on the rest of my system (battery, performance etc) and if there are likely to be any, I might reconsider my purchase. So if anyone can advise me on the effects, I would be very grateful, since I doubt I can just turn the card off. Thankyou for any assistance :)

  Read the article

• My internet connection slows or dies unexpectedly

  - by genesis

  I installed Ubuntu 10.04 once again and I'm having some problems which I had before, but I have no idea how I solved them. On Windows, everything's working fine and I had no problems with this. My problem is that sometimes, when browsing through the internet, webpages just start to load really slow, sometimes it doesn't load anything at all (Error 118 (net::ERR_CONNECTION_TIMED_OUT): The operation timed out.) and it starts to work after few minutes. My IPv4 settings are automatic (DHCP), and IPv6 settings are Ignored/Disabled. I think my previous problems had something to do with IPv6, but I'm not sure. Is there a fix for this? iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Fsite1" Mode:Managed Frequency:2.442 GHz Access Point: C8:3A:35:40:43:68 Bit Rate=0 kb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=43/70 Signal level=-67 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0

  Read the article

• Where can I configure wireless to be passed on to the Virtualbox guest?

  - by huahsin68

  I have WinXP install in virtualbox which host in Linux. I have a TP-Link (TP-WN321G) USB wifi adapter and have the driver installed inside WinXP. When I plug-in the wifi adapter, there is an option show "Ralink 802.11g WLAN [0101]" in the virtualbox's USB icon, tick on that option, the Device Manager able to detect the hardware which shows TP-Link, but when look into the properties, it says there is no driver was install. I did try to install Ralink driver but still no luck. Just curious why my wifi adapter is TP-Link, but the option show Ralink? May I know how can I emulate the wireless network inside WindowsXP?

  Read the article

• How do I set my router up to authenticate with my service provider?

  - by João Lourenço

  Currently I have this setup: D-Link DSL2640U connected to the phone line: VPI/VCI 0/40, Service Category UBR Without PCR Service pppoe_0_40_3 Interface nas_0_40 Protocol Bridging (LLC/SNAP-Bridging) 802.11q not enabled Bridge Service Enabled Computers have individual PPPoE connections (in Network and Sharing Centre - Set up a new connection or network - Connect to the Internet - Broadband (PPPoE) - Username and Password) How would I move these settings on each individual PC to the router so that all I need to do is connect to the wireless? I have been unsuccessful setting up anything other than Windows PCs on the network (I have tried Macs, iOS and Nokia SmartPhones too). Thanks for the responses in advance!

  Read the article

< Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >