Search Results

Search found 587 results on 24 pages for '802 1q'.

Page 18/24 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Can one use Airport (Time Capsule) with an external DHCP server?

  - by DNS

  I currently share my DSL connection using a wireless router with DHCP disabled, and dnsmasq running on a Mac Mini serving DHCP & DNS. This setup is important because I have clients doing PXE boot, and I need the control over DHCP that dnsmasq provides. There is also a Time Capsule on the network that's used purely as a backup device; its wireless functions are disabled. The wireless router is starting to get a little flaky, and since it doesn't support 802.11n I'd like to replace it. Rather than buying a new router, I'd like to just use the Time Capsule. But I see no way to disable its DHCP server; when I set the connection type to PPPoE, it insists on serving DHCP. Is there any way to use Airport PPPoE with a DHCP server elsewhere on the network?

  Read the article

• Is this a b43 driver problem?

  - by Nullet

  I have 13.04 on a Dell Inspiron 1564 with Broadcom 4312 WiFi card. The wl drivers cause kernel panic on linux-3.8 so I succesfully installed the b43 driver a couple of months ago. Now I have changed ISP and got a new router, and the connection drop when downloading software from internet to a 2008r2 using Remmina Client, and apt-get install on virtual machines in virtualbox. I have no idea why this suddenly became a problem.. My phone does not loose the connection, just Ubuntu. Output from /var/log/syslog after lost connection rfkill list(after disconnecting): 0: phy0: Wireless LAN Soft blocked: yes Hard blocked: yes I can use NetworkManager to disable wireless and then enable wireless to connect again. rfkill ublock all/wifi/0 removes only Soft blocked. lshw -C network *-network description: Wireless interface physical id: 4 logical name: wlan0 serial: 78:e4:00:78:d2:05 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.8.0-32-generic firmware=478.104 ip=10.0.0.3 link=yes multicast=yes wireless=IEEE lspci 04:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) After waking from suspend and when booting, it takes about 40 sec to get network connection. This has been a problem all along AND a different question, but I mention it anyway.. cus it's annoying! Please take a look and hopefully someone spot a problem! Thanks!

  Read the article

• decoding 802.11 b

  - by stan

  I have a raw grabbed data from spectrometer that was working on wifi (802.11b) channel 6. (two laptops in ad-hoc ping each other). I would like to decode this data in matlab. I see them as complex vector with 4.6 mln of complex samples. I see their spectrum quite nice. I am looking document a bit less complicated as IEEE 802.11 standard (which I have). I can share measurement data to other people.

  Read the article

• [Android] ProgressBar inside SimpleAdapter

  - by lemon

  I'm trying to add a ProgressBar to my row.xml view but I can't seem to make it work I keep getting 06-09 12:44:44.802: ERROR/AndroidRuntime(1012): java.lang.IllegalStateException: android.widget.ProgressBar is not a view that can be bounds by this SimpleAdapter ArrayList arr = new ArrayList(); HashMap map = new HashMap(); map.put("progress", 10); arr.add(map); String [] fieldNames = {"progress"}; int [] fieldIds = {R.id.progress}; SimpleAdapter adapter = new SimpleAdapter(this, arr, R.layout.row, fieldNames, fieldIds); list = (ListView) findViewById(R.id.list); list.setAdapter(adapter); <ProgressBar android:id="@+id/progress" style="?android:attr/progressBarStyleHorizontal" android:max="100" android:progress="5" android:layout_width="fill_parent" android:layout_height="fill_parent" /> Does anyone have any idea what I'm missing?

  Read the article

• How to bring out checboxes based on drop down list selection from DB

  - by user2199877

  I got stuck again. Can't overcome this step: loop through (in a form of checkboxes) pallets based on the lot drop down list selection, so it can be further submitted to complete the table. Please, please help. So, basically, first submit button (drop down menu) brings into the table lot number and description and also checkboxes to choose pallets. Second submit button (checboxes) brings into the table pallets numbers and weights. Thank you for any help. <?php mysql_connect('localhost','user',''); mysql_select_db('base'); $query="SELECT DISTINCT lot_number FROM pl_table"; $result=mysql_query($query); ?> <form action="" method="POST"> <select name="option_chosen"> <option>-- Select lot --</option> <?php while(list($lot_number)=mysql_fetch_row($result)) { echo "<option value=\"".$lot_number."\">".$lot_number."</option>"; } ?> </select> <input type='submit' name='submitLot' value='Submit' /> </form> <!-- need help here <h4>-- Select pallets --</h4> <form action="" method="POST"> <input type='submit' name='submitPal' value='Submit'/> </form> --> <table border="1" id="table"> <tr> <th width=80 height=30>Lot<br/>number</th> <th width=110 height=30>Description</th> <th width=90 height=30>Pallet<br/>number</th> <th width=60 height=30>Net</th> <th width=60 height=30>Gross</th> </tr> <?php if($_SERVER['REQUEST_METHOD'] =='POST') {$option_chosen=$_POST['option_chosen']; $query="SELECT * FROM pl_table WHERE lot_number='$option_chosen'"; $run=mysql_query($query); $row=mysql_fetch_array($run, MYSQLI_ASSOC); echo "<tr><td>".''."</td>"; echo "<td rowspan='5'>".$row['descr']."</td>"; echo "<td><b>".'Total weight'."<b></td>"; echo "<td>".''."</td><td>".''."</td></tr>"; echo "<td>".$row['lot_number']."</td>"; echo "<td colspan='3'>".''."</td>"; //This to be echoed when "select pallets" submited //echo "<tr><td>".$row['lot_number']."</td>"; //echo "<td>".$row['pallet_number']."</td>"; //echo "<td>".$row['net']."</td><td>".$row['gross']."</td></tr>"; } ?> </table> the table +--------------------------+-------------------------+---------+-------+ | id | lot_number | descr | pallet_number | net | gross | +--------------------------+-------------------------+---------+-------+ | 1 | 111 | black | 1 | 800 | 900 | | 2 | 111 | black | 2 | 801 | 901 | | 3 | 111 | black | 3 | 802 | 902 | | 4 | 222 | white | 1 | 800 | 900 | | 5 | 222 | white | 2 | 801 | 901 | | 6 | 222 | white | 3 | 802 | 902 | +--------------------------+-------------------------+---------+-------+

  Read the article

• mysql - check if data exists across multiple tables

  - by Dd Daym

  I am currently running this query inside MySQL to check if the specified values exists within the table associated with them. SELECT COUNT(artist.artist_id), COUNT(album.album_id), COUNT(tracks.track_id) FROM artist, album, tracks WHERE artist.artist_id = 320295 OR album.album_id = 1234 OR tracks.track_id = 809 The result I get from running this query is all 1, meaning that all the statements after the WHERE clause is true. To further check the query's reliability, I changed the tracks.track_ = 809 to 802, which I know does not match. However the results displayed are still all 1, meaning that they were all successfully matched even when I purposefully inserted a value which would not have matched. How do I get it to show 1 for a match and 0 for no matches within the same query? EDIT: I have inserted an image of the query running

  Read the article

• no volume in kubuntu 10.04

  - by neha

  hello,I am having both gnome and kde on my system.as my gnome is working perfectly but in KDE is there is no sound being generated. output of apley -l and lspci commands is as follows.. neha@neha-laptop:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 3: INTEL HDMI [INTEL HDMI] Subdevices: 1/1 Subdevice #0: subdevice #0 and output of lspci command is: neha@neha-laptop:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c) 00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02) 00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02) 02:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 02:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) 02:09.2 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 12) 02:09.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12) 02:09.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev ff) 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 12) 0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 01) can anyone help me??

  Read the article

• Ubuntu turns off instead of suspend / sleeping

  - by Marcos

  I'm using Ubuntu 11.10 on my notebook as the main OS. How ever, I've been facing a serious problem: Every time I try to suspend it, or it just stays idle for a while, the computer shuts down, instead of suspending. It actually seems to be suspended, but when I press the button the awake it, it turns on, the open works are all lost. How can i fix this? P.s: On windows 7 the suspend / sleep resumes just fine. Here is a complete list of hardware: 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) 00:1a.0 USB Controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b4) 00:1c.1 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 [8086:1c12] (rev b4) 00:1c.2 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 [8086:1c14] (rev b4) 00:1d.0 USB Controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 04) 01:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) 02:00.0 System peripheral [0880]: JMicron Technology Corp. SD/MMC Host Controller [197b:2382] (rev 80) 02:00.2 SD Host controller [0805]: JMicron Technology Corp. Standard SD Host Controller [197b:2381] (rev 80) 02:00.3 System peripheral [0880]: JMicron Technology Corp. MS Host Controller [197b:2383] (rev 80) 02:00.5 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 03) I've updated the kernel to 3.2 still and hibernate or suspend is still not working. SWAP is 1/4 of my RAM.

  Read the article

• Very very slow transfer speeds between Windows 7 and samba server running on Ubuntu 11.10/12.04 minimal

  - by kuzyt

  As mentioned in the title I tried transferring files between Windows 7 and the samba server running on both Ubuntu 11.10 and 12.04 but both showed very slow transfer speeds. Can someone please guide me in the right direction to debug this problem ? wget --output-document=/dev/null http://tokyo1.linode.com/100MB-tokyo.bin --2012-08-21 22:02:17-- http://tokyo1.linode.com/100MB-tokyo.bin Resolving tokyo1.linode.com (tokyo1.linode.com)... 106.187.33.12 Connecting to tokyo1.linode.com (tokyo1.linode.com)|106.187.33.12|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 104857600 (100M) [application/octet-stream] Saving to: `/dev/null' 8% [=============> ] 8,923,980 64.8K/s eta 15m 0s wlan0 IEEE 802.11abgn ESSID:"TNET" Mode:Managed Frequency:2.462 GHz Access Point: 58:6D:8F:26:20:7A Bit Rate=117 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=57/70 Signal level=-53 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:101 Invalid misc:2448 Missed beacon:0 03:00.0 Network controller: Atheros Communications Inc. AR9300 Wireless LAN adaptor (rev 01) Subsystem: Atheros Communications Inc. Device 3112 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fea00000 (64-bit, non-prefetchable) [size=128K] Expansion ROM at fea20000 [disabled] [size=64K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/4 Maskable+ 64bit+ Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [70] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <2us, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- Capabilities: [300 v1] Device Serial Number 00-00-00-00-00-00-00-00 Kernel driver in use: ath9k Kernel modules: ath9k

  Read the article

• Wireless not working with a RaLink RT3090

  - by Promather

  I recently bought a new HP DV6-3118SA laptop, but I am having a very discouraging problem with wireless LAN. It simply doesn't work! Could you please help me with this? Output of lspci -k: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) Subsystem: Hewlett-Packard Company Device 144a 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: i2c-i801 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: intel ips Kernel modules: intel_ips 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: radeon Kernel modules: radeon 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe Subsystem: Hewlett-Packard Company Device 1453 Kernel driver in use: rt2800pci Kernel modules: rt2860sta, rt2800pci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: r8169 Kernel modules: r8169 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a

  Read the article

• Wireless Not Working on Ubuntu 10.10

  - by Promather

  I recently bought a new HP DV6-3118SA laptop, but I am having a very discouraging problem with wireless LAN. It simply doesn't work! Could you please help me with this? EDIT: Following @Ronald and @Oli advice, I am dumping the output of lspci -k: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) Subsystem: Hewlett-Packard Company Device 144a 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: i2c-i801 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: intel ips Kernel modules: intel_ips 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: radeon Kernel modules: radeon 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe Subsystem: Hewlett-Packard Company Device 1453 Kernel driver in use: rt2800pci Kernel modules: rt2860sta, rt2800pci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: r8169 Kernel modules: r8169 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a

  Read the article

• Hostapd - WLAN as AP

  - by BBK

  I'm trying to start hostapd but without success. I'm using Headless Ubuntu 11.10 oneiric 3.0.0-16-server x86_64. WLAN driver is rt2800usb and my wireless nic card TP-Link TL-WN727N supports AP mode as shows below: us0# ifconfig wlan0 wlan0 Link encap:Ethernet HWaddr 00:27:19:be:cd:b6 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) us0# lsusb Bus 003 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter us0# lshw -C network *-network:3 description: Wireless interface physical id: 4 bus info: usb@3:2 logical name: wlan0 serial: 00:27:19:be:cd:b6 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.0.0-16-server firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn us0# hostapd /etc/hostapd/hostapd.conf Configuration file: /etc/hostapd/hostapd.conf Could not read interface wlan0 # The int flags: No such device nl80211 driver initialization failed. ELOOP: remaining socket: sock=4 eloop_data=0xd3e4a0 user_data=0xd3ecc0 handler=0x433880 ELOOP: remaining socket: sock=6 eloop_data=0xd411f0 user_data=(nil) handler=0x43cc10 us0# cat /etc/hostapd/hostapd.conf ssid=Home interface=wlan0 # The interface name of the card #driver=rt2800usb driver=nl80211 macaddr_acl=0 ieee80211n=1 channel=1 hw_mode=g auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=88888888 wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP us0# iw list Wiphy phy0 Band 1: Capabilities: 0x172 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI RX STBC 1-stream Max AMSDU length: 7935 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 2 usec (0x04) HT RX MCS rate indexes supported: 0-7, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) (passive scanning, no IBSS) * 2472 MHz [13] (20.0 dBm) (passive scanning, no IBSS) * 2484 MHz [14] (20.0 dBm) (passive scanning, no IBSS) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * Unknown command (68) * Unknown command (55) * Unknown command (57) * Unknown command (59) * Unknown command (67) * set_wiphy_netns * Unknown command (65) * Unknown command (66) * connect * disconnect The question is: Why the hostapd not starting?

  Read the article

• Macbook (non-pro, late 2010) Power Management Issues relating to Nvidia-Current drivers

  - by gbvitaobscura

  I have tried many potential solutions but to no avail! (this is going to be a long post) Essentially, when I first install ubuntu (I have tested 10.11-12.04 beta) I can change the brightness of the macbook backlight. One of the first things I usually do once my machine finishes installing is enter "sudo apt-get install nvidia-current" into the terminal to get my Nvidia graphics card set up. Before I install nvidia-current power management works flawlessly. After installing nvidia-current my graphics driver works mostly properly (more on that later). When I press F1 or F2 notify osd pops up and shows icon for the backlight along with a meter which changes according to how much I press F1 or F2, but the backlight does not change brightness at all. Two supplementary facts: when I am running off of battery power the backlight does not dim ever, also changing the backlight brightness through the terminal does not work (it recognizes the command but changes nothing). Things which did not work: 1. editing xorg.conf 2. python script/hack 3. editing grub Things which did work: 1. removing Nvidia-Current Final piece of information: Although my graphics card works in every way but Power Management it can not be found through System Settings/Details (Graphics Unknown) I'm using the NVIDIA GeForce 320M. the output of lspci is: 00:00.0 Host bridge: NVIDIA Corporation MCP89 HOST Bridge (rev a1) 00:00.1 RAM memory: NVIDIA Corporation MCP89 Memory Controller (rev a1) 00:01.0 RAM memory: NVIDIA Corporation Device 0d6d (rev a1) 00:01.1 RAM memory: NVIDIA Corporation Device 0d6e (rev a1) 00:01.2 RAM memory: NVIDIA Corporation Device 0d6f (rev a1) 00:01.3 RAM memory: NVIDIA Corporation Device 0d70 (rev a1) 00:02.0 RAM memory: NVIDIA Corporation Device 0d71 (rev a1) 00:02.1 RAM memory: NVIDIA Corporation Device 0d72 (rev a1) 00:03.0 ISA bridge: NVIDIA Corporation MCP89 LPC Bridge (rev a2) 00:03.1 RAM memory: NVIDIA Corporation MCP89 Memory Controller (rev a1) 00:03.2 SMBus: NVIDIA Corporation MCP89 SMBus (rev a1) 00:03.3 RAM memory: NVIDIA Corporation MCP89 Memory Controller (rev a1) 00:03.4 Co-processor: NVIDIA Corporation MCP89 Co-Processor (rev a1) 00:04.0 USB controller: NVIDIA Corporation MCP89 OHCI USB 1.1 Controller (rev a1) 00:04.1 USB controller: NVIDIA Corporation MCP89 EHCI USB 2.0 Controller (rev a2) 00:06.0 USB controller: NVIDIA Corporation MCP89 OHCI USB 1.1 Controller (rev a1) 00:06.1 USB controller: NVIDIA Corporation MCP89 EHCI USB 2.0 Controller (rev a2) 00:08.0 Audio device: NVIDIA Corporation MCP89 High Definition Audio (rev a2) 00:09.0 Ethernet controller: NVIDIA Corporation MCP89 Ethernet (rev a1) 00:0a.0 IDE interface: NVIDIA Corporation MCP89 SATA Controller (rev a2) 00:0b.0 RAM memory: NVIDIA Corporation Device 0d75 (rev a1) 00:15.0 PCI bridge: NVIDIA Corporation Device 0d9b (rev a1) 00:17.0 PCI bridge: NVIDIA Corporation MCP89 PCI Express Bridge (rev a1) 01:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01) 02:00.0 VGA compatible controller: NVIDIA Corporation Device 08a0 (rev a2) There is a very similar bug on Launchpad which I have posted below. https://bugs.launchpad.net/ubuntu/+source/nvidia-graphics-drivers/+bug/764195

  Read the article

• Ubuntu 12.10 Trackpoint not detected Thinkpad X130e

  - by killerknives

  I just did a fresh install of 12.10 and now only my touchpad works. The trackpoint and Left/Right buttons below the trackpoint do not work. The trackpoint worked fine as of 12.04. I've searched online and there was a hack that said that disabling the touchpad would enable the trackpoint. WRONG! You'll end up having to use the keyboard =/. I don't know what is needed so I'll just dump some stuff. lspci: 00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Complex 00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Wrestler [Radeon HD 6310] 00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Wrestler HDMI Audio [Radeon HD 6250/6310] 00:05.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:06.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:07.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 42) 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (rev 40) 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 0 (rev 43) 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 1 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 2 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 3 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 4 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 6 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 5 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 7 01:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 02:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0) I've installged gpointing-device-setting and it only lists the touchpad. No trackpoint. What should I do? What data do you need?

  Read the article

• Can not connect to wireless on 12.04 with Intel WiFi Link 5100

  - by WiData

  I am having problem in connecting to wifi. I have dual boot (Windows 7 and Ubuntu 12.04) on my Dell Studio 15. I upgraded to 12.04 quite some time ago (at least one month) from 11.10. Everything was working fine till yesterday. Since yesterday I can see the list of available Wifi connection but does not connect to any or if connects (after hours of trying) then disconnects after few minutes. My wifi interface is Intel WiFi Link 5100 AGN. However the problem is on both Windows and Ubuntu. Here are outputs of some commands which may be useful for those interested in helping: ~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:22:19:fa:65:bb UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:794 errors:0 dropped:0 overruns:0 frame:0 TX packets:794 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:56280 (56.2 KB) TX bytes:56280 (56.2 KB) wlan0 Link encap:Ethernet HWaddr 00:22:fb:d2:fc:ce UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:239 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:53603 (53.6 KB) Here is the output for the command sudo lshw -C network *-network description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:22:fb:d2:fc:ce width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-48-generic-pae firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:f8000000-f8001fff My kernel version is kernel version 3.2.0-48-generic-pae I also checked this post which was helpful. But I am not sure if what is the exact problem. Any suggestions will be helpful. Should I be changing the firmware/driver? Currently my /lib/firmware has following iwlwifi files /lib/firmware/iwlwifi-1000-5.ucode /lib/firmware/iwlwifi-5000-5.ucode /lib/firmware/iwlwifi-100-5.ucode /lib/firmware/iwlwifi-5150-2.ucode /lib/firmware/iwlwifi-105-6.ucode /lib/firmware/iwlwifi-6000-4.ucode /lib/firmware/iwlwifi-135-6.ucode /lib/firmware/iwlwifi-6000g2a-5.ucode /lib/firmware/iwlwifi-2000-6.ucode /lib/firmware/iwlwifi-6000g2a-6.ucode /lib/firmware/iwlwifi-2030-6.ucode /lib/firmware/iwlwifi-6000g2b-6.ucode /lib/firmware/iwlwifi-3945-2.ucode /lib/firmware/iwlwifi-6050-5.ucode /lib/firmware/iwlwifi-4965-2.ucode Thanks a lot for the help.

  Read the article

• Ubuntu 12.04 can't detect internal mobile broadband (Gobi 2000)

  - by Anega

  Hi I have been trying Ubuntu to detect and connect using the buit in mobile broadband capability in my HP 110 netbook but until now nothing seems to work Output of lspci command: 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [AHCI mode] (rev 02) 01:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 02:00.0 Ethernet controller: Atheros Communications Inc. AR8132 Fast Ethernet (rev c0) Output of lsusb command: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 1fea:0008 Bus 005 Device 002: ID 03f0:2a1d Hewlett-Packard Bus 001 Device 005: ID 03f0:241d Hewlett-Packard Gobi 2000 Wireless Modem (QDL mode) So far I have been trying what is intended on several pages, trying to update firmware using wine and then moving .mda or whatever files the update package GobiInstaller.mdi throws out. The results are always the same: After running Output of wine msiexec /a GobiInstaller.msi /qb TARGETDIR="c:\temp" fixme:advapi:GetCurrentHwProfileA (0x33fba8) semi-stub fixme:heap:HeapSetInformation (nil) 1 (nil) 0 fixme:win:RegisterDeviceNotificationA (hwnd=0x13e250, filter=0xf7e984,flags=0x00000001) returns a fake device notification handle! fixme:heap:HeapSetInformation (nil) 1 (nil) 0 fixme:heap:HeapSetInformation (nil) 1 (nil) 0 fixme:advapi:RegisterEventSourceW ((null),L"Bonjour Service"): stub fixme:advapi:ReportEventA (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x79e58c,(nil)): stub fixme:advapi:ReportEventW (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x12e6d0,(nil)): stub fixme:winsock:WSAIoctl WS_SIO_UDP_CONNRESET stub fixme:winsock:WSAIoctl -> SIO_ADDRESS_LIST_CHANGE request: stub fixme:iphlpapi:DeleteIpForwardEntry (pRoute 0x79e920): stub fixme:iphlpapi:CreateIpForwardEntry (pRoute 0x79e958): stub fixme:advapi:ReportEventA (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x79e58c,(nil)): stub fixme:advapi:ReportEventW (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x12e6d0,(nil)): stub fixme:service:EnumServicesStatusW resume handle not supported fixme:service:EnumServicesStatusW resume handle not supported fixme:advapi:ReportEventA (0xcafe4242,0x0004,0x0000,0x00000064,(nil),0x0001,0x00000000,0x79e58c,(nil)): stub fixme:advapi:ReportEventW (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x12e6d0,(nil)): stub fixme:netapi32:NetGetJoinInformation Semi-stub (null) 0x79e644 0x79e63c fixme:winsock:WSAIoctl WS_SIO_UDP_CONNRESET stub fixme:storage:create_storagefile Storage share mode not implemented. err:msi:ITERATE_Actions Execution halted, action L"_693CD41C_A4A2_4FA1_8888_FC56C9E6E13B" returned 1603 err:rpc:I_RpcGetBuffer no binding err:rpc:I_RpcGetBuffer no binding andres@andres-HP-Mini-110-1100:~/.wine/drive_c/Qualcomm$ fixme:advapi:ReportEventA (0xcafe4242,0x0004,0x0000,0x00000064,(nil),0x0001,0x00000000,0x79e588,(nil)): stub fixme:advapi:ReportEventW (0xcafe4242,0x0004,0x0000,0x00000064, (nil),0x0001,0x00000000,0x12e6d0,(nil)): stub And creates 2 empty folders, I have been trying hard and I am not sure if I am doing it the way it should be. Thanks

  Read the article

• Display Driver Issue on an hp TX2-1160ea Notebook

  - by Sam

  I'm new to Linux and recently switched to Ubuntu 11.04 due to my project requirement. My laptop has been freezing and going to black screen of death when I run anything related to display (Share desktop, stream video, etc). Today I went through the Ubuntu forum to install the appropriate graphic driver and, after doing it, I rebooted my PC. It gave an error before login saying "select the recovery mode" and after clicking OK, it didn't give the same error on reboot but I've lost the 11.04 graphical interface and all I see is the interface of Ubuntu v10 with slow visuals (even scrolling up/down on browser is really slow). For the reference, here's a desktop screenshot so that you can understand the situation. Also the laptop is overheating. How can I fix this problem? How can i get the Ubuntu 11.04 view back? I also tried Google, but couldn't find any issue like this. Some general Information: Laptop: HP TouchSmart TX2-1160ea Processor: AMD Turion TX2 Memory: 4GB OS: Ubuntu 11.04 Some debugging information:: $ report-hw | grep controller lspci -knn: 00:11.0 SATA controller [0106]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] lspci -knn: 00:14.3 ISA bridge [0601]: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] lspci -knn: 01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS780M/RS780MN [Radeon HD 3200 Graphics] [1002:9612] lspci -knn: 08:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01) lspci -knn: 09:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02) And: $ dpkg -l '*fglrx*' Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Description +++-==============-==============-============================================ ii fglrx 2:8.840-0ubunt Video driver for the ATI graphics accelerato ii fglrx-amdcccle 2:8.840-0ubunt Catalyst Control Center for the ATI graphics un fglrx-control <none> (no description available) un fglrx-control- <none> (no description available) ii fglrx-dev 2:8.840-0ubunt Video driver for the ATI graphics accelerato un fglrx-driver <none> (no description available) un fglrx-driver-d <none> (no description available) un fglrx-kernel-s <none> (no description available) un fglrx-modalias <none> (no description available) un xfree86-driver <none> (no description available) un xfree86-driver <none> (no description available) un xorg-driver-fg <none> (no description available) un xorg-driver-fg <none> (no description available) If you need any more information that could help, just ask.

  Read the article

• How to install Network Adapter Drivers for Atheros AR8161/8165 PCI-E Gigabit Ethernet Controller (NDIS 6.20) Ubuntu 12.04

  - by Jessica Burnett

  How can I install drivers for 64-bit Atheros AR8161/8165 PCI-E Gigabit Ethernet Controller (NDIS 6.20) for Ubuntu 12.04. I dual boot Windows7/Ubuntu 12.04 drivers work for 64-bit Windows 7. lspic -nn: 00:00.0 Host bridge [0600]: Intel Corporation Ivy Bridge DRAM Controller [8086:0154] (rev 09) 00:01.0 PCI bridge [0604]: Intel Corporation Ivy Bridge PCI Express Root Port [8086:0151] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation Ivy Bridge Graphics Controller [8086:0166] (rev 09) 00:14.0 USB controller [0c03]: Intel Corporation Panther Point USB xHCI Host Controller [8086:1e31] (rev 04) 00:16.0 Communication controller [0780]: Intel Corporation Panther Point MEI Controller #1 [8086:1e3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation Panther Point High Definition Audio Controller [8086:1e20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 1 [8086:1e10] (rev c4) 00:1c.1 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 2 [8086:1e12] (rev c4) 00:1c.3 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 4 [8086:1e16] (rev c4) 00:1d.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #1 [8086:1e26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation Panther Point LPC Controller [8086:1e59] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] [8086:1e03] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation Panther Point SMBus Controller [8086:1e22] (rev 04) 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation Device [10de:0de9] (rev a1) 02:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8161 Gigabit Ethernet [1969:1091] (rev 08) 03:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 2200 [8086:0891] (rev c4) 04:00.0 System peripheral [0880]: JMicron Technology Corp. SD/MMC Host Controller [197b:2392] (rev 30) 04:00.2 SD Host controller [0805]: JMicron Technology Corp. Standard SD Host Controller [197b:2391] (rev 30) 04:00.3 System peripheral [0880]: JMicron Technology Corp. MS Host Controller [197b:2393] (rev 30) 04:00.4 System peripheral [0880]: JMicron Technology Corp. xD Host Controller [197b:2394] (rev 30) sudo lshw -c network *-network UNCLAIMED description: Ethernet controller product: AR8161 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 version: 08 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi msix bus_master cap_list configuration: latency=0 resources: memory:d3a00000-d3a3ffff ioport:2000(size=128) *-network description: Wireless interface product: Centrino Wireless-N 2200 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: c4 serial: 9c:4e:36:14:d4:7c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-23-generic firmware=18.168.6.1 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:45 memory:d3900000-d3901fff I also tried Manually configuring wired connection. Nether wired or wireless connects

  Read the article

• Getting WLAN on my Laptop to work (Medion MD98300)

  - by Anand Böhmer

  Dear Ubuntu Community, I am having difficulties to get the WLAN Adapter on my Medion 98300 Laptop to work. The WLAN Card seems to be connected through an internal USB Interface and the Card itself had shown up as a wirelles Network while installing Ubuntu. I have tried a few things earlier, but none of my google reasearches have brought me to a working solution... I am quite new to the Linux System and only knoew a couple of terminal commands so far, so I probably have missed out on a few possible solutions. Maybe you can help me? Thank you very much in advance! A fre minimal technical Details: AMD Turion 64 X2 Dual-Core Mobile Technolgie TL-50 NVIDIA GeForce Go 6150 SanDisk 64GB SSD 2GB RAM DDR2 667 nForce Chipset (I forgt the Version, but deductable from the GPU I guess) WiFi: ZyDAS ZD1211B 802.11g Thank's a lot again! :) UPDATE: I tried around myself a little and found a guide on the Linux Mint forums that helped! I already had tried to install the linux backport modules etc. What I finally did was update the linux firmware and run the following command: echo "options acer_wmi wirelles=1" sudo tee /etc/modprobe.d/acer_wmi.conf and rebooted now I found and could connect to networks, but unfortunately I found, that the link quality was very bad, around 40 to 50. Eventhough my Router is running at high power and is only 6 Meters away! I then switched a few channels, but that did not improve much. Before, under Windows, I had a very good link quality and had the entire 16mbit/s internet connection at disposal, now I can only get about 3-5Mbit/s. better then nothing, but still pretty bad! The "TX power" is fixed on 20dBm and iwconfig says, that the "Power Management" is off... Maybe the power of the module is set too low?... UPDATE2: I figured that 20dBm is a normal power output. I even tried to change the power using iwconfig wlan0 txpower INTEGERHERE but, obviously my "Card" does not support more then 20. More would probably be illegal as well, so I won't even use more then 20. I guess that I will have to figure out a way, or maybe just switch cards. Are the Mailboard-USB-Connectors on a laptop of the same property as the standard external ones? If so, I could simply solder a micro Wirelless N Adapter onto the board :)

  Read the article

• What are these errors when I try to "make" the driver of my wireless adapter?

  - by Tom Brito

  I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

  Read the article

• Wireless Broadcom 4313 not working on Ubuntu 12.04

  - by user88568

  It seems a lot of people are having this problem, but none of the posted solutions have worked for me so far. My driver is installed and activated, I have tried removing and re-adding the network, and various other fixes. No networks were picked up on my first boot, the next day wireless worked fine, and since then it does not detect networks, and when I manually try to connect, it repeatedly asks for the password and does not connect. Here's my info: 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Dell Inspiron M5010 / XPS 8300 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f0500000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information: Len=78 Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 00-00-a1-ff-ff-f3-70-f1 Capabilities: [16c] Power Budgeting Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac root@michelle-laptop:/home/michelle# ifconfig eth0 Link encap:Ethernet HWaddr 70:f1:a1:f3:ba:ab inet6 addr: fe80::72f1:a1ff:fef3:baab/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:29 TX packets:0 errors:30 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 eth1 Link encap:Ethernet HWaddr f0:4d:a2:53:83:7a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:104 errors:0 dropped:0 overruns:0 frame:0 TX packets:104 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8000 (8.0 KB) TX bytes:8000 (8.0 KB) root@michelle-laptop:/home/michelle# lsmod Module Size Used by dm_crypt 22528 0 snd_hda_codec_hdmi 31775 1 snd_hda_codec_realtek 174313 1 snd_hda_intel 32765 5 snd_hda_codec 109562 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80845 4 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event parport_pc 32114 0 ppdev 12849 0 binfmt_misc 17292 1 lib80211_crypt_tkip 17275 0 bnep 17830 2 rfcomm 38139 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq joydev 17393 0 wl 2646601 0 snd 62064 19 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd btusb 17912 0 bluetooth 158438 11 bnep,rfcomm,btusb uvcvideo 67203 0 videodev 86588 1 uvcvideo snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lib80211 14040 2 lib80211_crypt_tkip,wl intel_ips 17822 0 psmouse 72919 0 serio_raw 13027 0 mei 36570 0 dell_laptop 17767 0 dell_wmi 12601 0 dcdbas 14098 1 dell_laptop sparse_keymap 13658 1 dell_wmi mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid wmi 18744 1 dell_wmi i915 414817 3 atl1c 36718 0 drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 root@michelle-laptop:/home/michelle# iwlist scan lo Interface doesn't support scanning. eth1 Interface doesn't support scanning. eth0 No scan results root@michelle-laptop:/home/michelle# rfkill list 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no Obviously I don't know what I'm doing. I'd appreciate any help! Thanks!

  Read the article

• Fan not detected by lm-sensors

  - by OrangeTux

  My fan is blowing hard, while my cpu temperature is 32 degrees I tried a lot of things to control my fan. Changed grub file GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi= pci=noacpi" _ GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi=\"Linux\"" Ran sensors-detect : To load everything that is needed, add this to /etc/modules: #----cut here---- # Chip drivers coretemp #----cut here---- If you have some drivers built into your kernel, the list above will contain too many modules. Skip the appropriate ones! Do you want to add these lines automatically to /etc/modules? (yes/NO) Unloading i2c-dev... OK Unloading i2c-i801... OK Unloading cpuid... OK Ran sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +34.0°C (crit = +90.0°C) coretemp-isa-0000 Adapter: ISA adapter Core 0: +34.0°C (high = +80.0°C, crit = +90.0°C) Core 2: +34.0°C (high = +80.0°C, crit = +90.0°C) Ran sudo start module-init-tools and sudo start module-init-tools module-init-tools stop/waiting As you can see my fan isn't detected. Running fancontrol gives me this: Loading configuration from /etc/fancontrol ... Error: Can't read configuration file Can you help me, please? I cannot use my laptop now in class. Thanks in advance. My system 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5400 Series] 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05)

  Read the article

• Vostro 3560 Wireless on Ubuntu 12.10

  - by ngille

  I have been using Ubuntu 12.04.1 LTS on a Dell Vostro 3560 for some time now. At first I had issues with the wireless but I was pointed to a driver from Ubuntu 11.xx for a Broadcom BCM43142 and that did work! however with the upgrade to 12.10 I find myself at a lost because the driver will not work anymore. When trying to reinstall it I get "Driver of bad quality" I still install it but it just wont work. I cant seem to find anything on this issue for 12.10 and didn't know if anyone had any advice or if someone could point me in the right direction on resources to write my own driver for it. As I know C/C++ but have never written a driver for a Linux machine before. Thanks for any help! To be more clear I installed Ubuntu 12.10 Desktop on my Dell Vostro 3560 laptop. When I log in, my wireless card isn't visible in the Network Manager popup menu, although the wired network shows up there. I installed the driver mentioned below and that did help me on 12.04 but is now broken due to "Poor quality" a sudo lspci -nn command brings up: 00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM Controller [8086:0154] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) 00:1c.1 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 [8086:1e12] (rev c4) 00:1c.2 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 3 [8086:1e14] (rev c4) 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation HM77 Express Chipset LPC Controller [8086:1e57] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04) 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 07) **02:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01)**

  Read the article

• WiFi connected to router, but no internet connection

  - by Quetzacotl

  I just got a new notebook, a ThinkPad Edge E530, and installed Ubuntu on it. I'm pretty new to Ubuntu. On the same laptop, running Windows 7, the Wi-Fi connection works fine. Ethernet connection works both on Win7 and on Ubuntu. Only Wi-Fi on Ubuntu does not work; it connects to the Wi-Fi access point but I don't have Internet access. My wireless card is Intel Centrino Wireless-N 2230. What can fix the problem? EDIT: ifconfig -a eth0 Link encap:Ethernet HWaddr b8:88:e3:30:72:34 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:163 errors:0 dropped:0 overruns:0 frame:0 TX packets:163 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10124 (10.1 KB) TX bytes:10124 (10.1 KB) usb0 Link encap:Ethernet HWaddr 02:15:e0:ec:01:00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 68:5d:43:43:71:e1 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe43:71e1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2801 (2.8 KB) TX bytes:26230 (26.2 KB) route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 cat /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 127.0.0.1 iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"SATELITE" Mode:Managed Frequency:2.462 GHz Access Point: 00:1F:1F:8D:CC:08 Bit Rate=1 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=60/70 Signal level=-50 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:93 Invalid misc:243 Missed beacon:0 eth0 no wireless extensions.

  Read the article

• How can I fix broken i915 drivers for Intel GPUs?

  - by Alen Mujezinovic

  I've got troubles getting the i915 drivers to work correctly on my laptop (HP Pavilion DM4 2101ea). Specifically, the laptop screen goes black and stays black after the splash graphic when booting both from USB key and from harddrive. To get anything on to the display after the splash screen I have to boot either with acpi=off nomodeset i915.modeset=0 I'd rather not turn ACPI off because I like my fans spinning and nomodeset is a bit overkill, so for now I'm booting with i915.modeset=0. Unfortunately, this turns off KMS and my current maximum resolution on the laptop screen is fixed to 1024x768 instead of its real capability. When not setting any of the above boot flags and I plug in an external monitor, the external monitor works fine. When booting with the flags, the external monitor works fine too, but can only do 1024x768 and can't do anything else than mirroring the laptop display. I did upgrade the i915 drivers from 2.17 that ship with Precise to 2.19 which are the most recent ones but without luck of getting anything to display. Here's my lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 02:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5116 PCI Express Card Reader (rev 01) 08:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0) Here's lshw -C video *-display UNCLAIMED description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list configuration: latency=0 resources: memory:c0000000-c03fffff memory:b0000000-bfffffff ioport:4000(size=64) Both outputs are generated after booting with i915.modeset=0. Here's a complete Xorg.log file from a boot into a black screen: https://gist.github.com/479ce06454e47d6123e1 The graphics card is a Intel HD 3000 integrated GPU. I've never had problems with Intel hardware on Ubuntu before so this is very surprising. If you could provide a method to make i915 work, suggest alternative drivers a way to boot with i915.modeset=0 but higher resolutions and KMS on or explain what is happening and how to fix it I'll give you an answer badge. :) Thanks

  Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24  | Next Page >