Search Results

Search found 2945 results on 118 pages for 'reverse tunnel'.

Page 16/118 | < Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >

  • Enable Cisco ASA as an SSH Tunneling

    - by Jim
    I am trying to utilize my Cisco ASA as a SSH Tunnel. I've configured this before when using a Linux server as the SSH target, however I cannot seem to get it to work with the ASA. I have configured and enabled SSH on the Cisco ASA, as well as a username that I can SSH to the console, however the SSH Tunneling feature does not work. For example, on my PC I use Putty with a Local Tunnel defined to a server behind the ASA. I should be able to (if SSH connected to the ASA) be able to access the server. See screenshot of putty. has anyone come across this before? Again this is to use my Cisco ASA as a SSH tunnel, this is not a port forwarding. -Jim

    Read the article

  • Do I need to have a proxy server to have HTTP over SSH?

    - by Johnes thomas
    I want to use HTTP over SSH since in my university most of the sites are blocked. I have my own server to which I can using SSH. What I'm doing right now is have a squid proxy run on the server on a particular port. Then connect using putty to my server via ssh and create a tunnel from a certain local port (which I will enter as proxy server in Firefox) to the squid server. So in putty the configuration is like this for the tunnel: source port:8080 destination:localhost:3128 I want to know is there any other way other than running the squid proxy on my server to tunnel the packets? Thanks.

    Read the article

  • ssh: which side is running the SOCKS proxy?

    - by Barry Brown
    When I set up a tunnel using dynamic forwarding (ssh -D), which side is running the SOCKS proxy? That is, is the proxy running on the local end (client) or the remote end (server)? Here's the situation: I want to set up several tunnels chained together using -L. Should the -D tunnel be the last one in the chain or the first one? Edit: I found the answer to the second paragraph on Super User (the -D tunnel should be at the remotest end). But I'd still like to know where the proxy code is running.

    Read the article

  • IPsec tunnel to Android device not created even though there is an IKE SA

    - by Quentin Swain
    I'm trying to configure a VPN tunnel between an Android device running 4.1 and a Fedora 17 Linux box running strongSwan 5.0. The device reports that it is connected and strongSwan statusall returns that there is an IKE SA, but doesn't display a tunnel. I used the instructions for iOS in the wiki to generate certificates and configure strongSwan. Since Android uses a modified version of racoon this should work and since the connection is partly established I think I am on the right track. I don't see any errors about not being able to create the tunnel. This is the configuration for the strongSwan connection conn android2 keyexchange=ikev1 authby=xauthrsasig xauth=server left=96.244.142.28 leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=%any rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem ike=aes256-sha1-modp1024 auto=add This is the output of strongswan statusall Status of IKE charon daemon (strongSwan 5.0.0, Linux 3.3.4-5.fc17.x86_64, x86_64): uptime: 20 minutes, since Oct 31 10:27:31 2012 malloc: sbrk 270336, mmap 0, used 198144, free 72192 worker threads: 8 of 16 idle, 7/1/0/0 working, job queue: 0/0/0/0, scheduled: 7 loaded plugins: charon aes des sha1 sha2 md5 random nonce x509 revocation constraints pubkey pkcs1 pkcs8 pgp dnskey pem openssl fips-prf gmp xcbc cmac hmac attr kernel-netlink resolve socket-default stroke updown xauth-generic Virtual IP pools (size/online/offline): android-hybrid: 1/0/0 android2: 1/1/0 Listening IP addresses: 96.244.142.28 Connections: android-hybrid: %any...%any IKEv1 android-hybrid: local: [C=CH, O=strongSwan, CN=vpn.strongswan.org] uses public key authentication android-hybrid: cert: "C=CH, O=strongSwan, CN=vpn.strongswan.org" android-hybrid: remote: [%any] uses XAuth authentication: any android-hybrid: child: dynamic === dynamic TUNNEL android2: 96.244.142.28...%any IKEv1 android2: local: [C=CH, O=strongSwan, CN=vpn.strongswan.org] uses public key authentication android2: cert: "C=CH, O=strongSwan, CN=vpn.strongswan.org" android2: remote: [C=CH, O=strongSwan, CN=client] uses public key authentication android2: cert: "C=CH, O=strongSwan, CN=client" android2: remote: [%any] uses XAuth authentication: any android2: child: 0.0.0.0/0 === 10.0.0.0/24 TUNNEL Security Associations (1 up, 0 connecting): android2[3]: ESTABLISHED 10 seconds ago, 96.244.142.28[C=CH, O=strongSwan, CN=vpn.strongswan.org]...208.54.35.241[C=CH, O=strongSwan, CN=client] android2[3]: Remote XAuth identity: android android2[3]: IKEv1 SPIs: 4151e371ad46b20d_i 59a56390d74792d2_r*, public key reauthentication in 56 minutes android2[3]: IKE proposal: AES_CBC_256/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024 The output of ip -s xfrm policy src ::/0 dst ::/0 uid 0 socket in action allow index 3851 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use - src ::/0 dst ::/0 uid 0 socket out action allow index 3844 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use - src ::/0 dst ::/0 uid 0 socket in action allow index 3835 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use - src ::/0 dst ::/0 uid 0 socket out action allow index 3828 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use - src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 socket in action allow index 3819 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use 2012-10-31 13:29:39 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 socket out action allow index 3812 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use 2012-10-31 13:29:22 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 socket in action allow index 3803 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use 2012-10-31 13:29:20 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 socket out action allow index 3796 priority 0 ptype main share any flag (0x00000000) lifetime config: limit: soft 0(bytes), hard 0(bytes) limit: soft 0(packets), hard 0(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:29:08 use 2012-10-31 13:29:20 So a xfrm policy isn't being created for the connection, even though there is an SA between device and strongswan. Executing ip -s xfrm policy on the android device results in the following output: src 0.0.0.0/0 dst 10.0.0.2/32 uid 0 dir in action allow index 40 priority 2147483648 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:08 use - tmpl src 96.244.142.28 dst 25.239.33.30 proto esp spi 0x00000000(0) reqid 0(0x00000000) mode tunnel level required share any enc-mask 00000000 auth-mask 00000000 comp-mask 00000000 src 10.0.0.2/32 dst 0.0.0.0/0 uid 0 dir out action allow index 33 priority 2147483648 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:08 use - tmpl src 25.239.33.30 dst 96.244.142.28 proto esp spi 0x00000000(0) reqid 0(0x00000000) mode tunnel level required share any enc-mask 00000000 auth-mask 00000000 comp-mask 00000000 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 dir 4 action allow index 28 priority 0 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:04 use 2012-10-31 13:42:08 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 dir 3 action allow index 19 priority 0 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:04 use 2012-10-31 13:42:08 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 dir 4 action allow index 12 priority 0 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:04 use 2012-10-31 13:42:06 src 0.0.0.0/0 dst 0.0.0.0/0 uid 0 dir 3 action allow index 3 priority 0 share any flag (0x00000000) lifetime config: limit: soft (INF)(bytes), hard (INF)(bytes) limit: soft (INF)(packets), hard (INF)(packets) expire add: soft 0(sec), hard 0(sec) expire use: soft 0(sec), hard 0(sec) lifetime current: 0(bytes), 0(packets) add 2012-10-31 13:42:04 use 2012-10-31 13:42:07 Logs from charon: 00[DMN] Starting IKE charon daemon (strongSwan 5.0.0, Linux 3.3.4-5.fc17.x86_64, x86_64) 00[KNL] listening on interfaces: 00[KNL] em1 00[KNL] 96.244.142.28 00[KNL] fe80::224:e8ff:fed2:18b2 00[CFG] loading ca certificates from '/etc/strongswan/ipsec.d/cacerts' 00[CFG] loaded ca certificate "C=CH, O=strongSwan, CN=strongSwan CA" from '/etc/strongswan/ipsec.d/cacerts/caCert.pem' 00[CFG] loading aa certificates from '/etc/strongswan/ipsec.d/aacerts' 00[CFG] loading ocsp signer certificates from '/etc/strongswan/ipsec.d/ocspcerts' 00[CFG] loading attribute certificates from '/etc/strongswan/ipsec.d/acerts' 00[CFG] loading crls from '/etc/strongswan/ipsec.d/crls' 00[CFG] loading secrets from '/etc/strongswan/ipsec.secrets' 00[CFG] loaded RSA private key from '/etc/strongswan/ipsec.d/private/clientKey.pem' 00[CFG] loaded IKE secret for %any 00[CFG] loaded EAP secret for android 00[CFG] loaded EAP secret for android 00[DMN] loaded plugins: charon aes des sha1 sha2 md5 random nonce x509 revocation constraints pubkey pkcs1 pkcs8 pgp dnskey pem openssl fips-prf gmp xcbc cmac hmac attr kernel-netlink resolve socket-default stroke updown xauth-generic 08[NET] waiting for data on sockets 16[LIB] created thread 16 [15338] 16[JOB] started worker thread 16 11[CFG] received stroke: add connection 'android-hybrid' 11[CFG] conn android-hybrid 11[CFG] left=%any 11[CFG] leftsubnet=(null) 11[CFG] leftsourceip=(null) 11[CFG] leftauth=pubkey 11[CFG] leftauth2=(null) 11[CFG] leftid=(null) 11[CFG] leftid2=(null) 11[CFG] leftrsakey=(null) 11[CFG] leftcert=serverCert.pem 11[CFG] leftcert2=(null) 11[CFG] leftca=(null) 11[CFG] leftca2=(null) 11[CFG] leftgroups=(null) 11[CFG] leftupdown=ipsec _updown iptables 11[CFG] right=%any 11[CFG] rightsubnet=(null) 11[CFG] rightsourceip=96.244.142.3 11[CFG] rightauth=xauth 11[CFG] rightauth2=(null) 11[CFG] rightid=%any 11[CFG] rightid2=(null) 11[CFG] rightrsakey=(null) 11[CFG] rightcert=(null) 11[CFG] rightcert2=(null) 11[CFG] rightca=(null) 11[CFG] rightca2=(null) 11[CFG] rightgroups=(null) 11[CFG] rightupdown=(null) 11[CFG] eap_identity=(null) 11[CFG] aaa_identity=(null) 11[CFG] xauth_identity=(null) 11[CFG] ike=aes256-sha1-modp1024 11[CFG] esp=aes128-sha1-modp2048,3des-sha1-modp1536 11[CFG] dpddelay=30 11[CFG] dpdtimeout=150 11[CFG] dpdaction=0 11[CFG] closeaction=0 11[CFG] mediation=no 11[CFG] mediated_by=(null) 11[CFG] me_peerid=(null) 11[CFG] keyexchange=ikev1 11[KNL] getting interface name for %any 11[KNL] %any is not a local address 11[KNL] getting interface name for %any 11[KNL] %any is not a local address 11[CFG] left nor right host is our side, assuming left=local 11[CFG] loaded certificate "C=CH, O=strongSwan, CN=vpn.strongswan.org" from 'serverCert.pem' 11[CFG] id '%any' not confirmed by certificate, defaulting to 'C=CH, O=strongSwan, CN=vpn.strongswan.org' 11[CFG] added configuration 'android-hybrid' 11[CFG] adding virtual IP address pool 'android-hybrid': 96.244.142.3/32 13[CFG] received stroke: add connection 'android2' 13[CFG] conn android2 13[CFG] left=96.244.142.28 13[CFG] leftsubnet=0.0.0.0/0 13[CFG] leftsourceip=(null) 13[CFG] leftauth=pubkey 13[CFG] leftauth2=(null) 13[CFG] leftid=(null) 13[CFG] leftid2=(null) 13[CFG] leftrsakey=(null) 13[CFG] leftcert=serverCert.pem 13[CFG] leftcert2=(null) 13[CFG] leftca=(null) 13[CFG] leftca2=(null) 13[CFG] leftgroups=(null) 13[CFG] leftupdown=ipsec _updown iptables 13[CFG] right=%any 13[CFG] rightsubnet=10.0.0.0/24 13[CFG] rightsourceip=10.0.0.2 13[CFG] rightauth=pubkey 13[CFG] rightauth2=xauth 13[CFG] rightid=(null) 13[CFG] rightid2=(null) 13[CFG] rightrsakey=(null) 13[CFG] rightcert=clientCert.pem 13[CFG] rightcert2=(null) 13[CFG] rightca=(null) 13[CFG] rightca2=(null) 13[CFG] rightgroups=(null) 13[CFG] rightupdown=(null) 13[CFG] eap_identity=(null) 13[CFG] aaa_identity=(null) 13[CFG] xauth_identity=(null) 13[CFG] ike=aes256-sha1-modp1024 13[CFG] esp=aes128-sha1-modp2048,3des-sha1-modp1536 13[CFG] dpddelay=30 13[CFG] dpdtimeout=150 13[CFG] dpdaction=0 13[CFG] closeaction=0 13[CFG] mediation=no 13[CFG] mediated_by=(null) 13[CFG] me_peerid=(null) 13[CFG] keyexchange=ikev0 13[KNL] getting interface name for %any 13[KNL] %any is not a local address 13[KNL] getting interface name for 96.244.142.28 13[KNL] 96.244.142.28 is on interface em1 13[CFG] loaded certificate "C=CH, O=strongSwan, CN=vpn.strongswan.org" from 'serverCert.pem' 13[CFG] id '96.244.142.28' not confirmed by certificate, defaulting to 'C=CH, O=strongSwan, CN=vpn.strongswan.org' 13[CFG] loaded certificate "C=CH, O=strongSwan, CN=client" from 'clientCert.pem' 13[CFG] id '%any' not confirmed by certificate, defaulting to 'C=CH, O=strongSwan, CN=client' 13[CFG] added configuration 'android2' 13[CFG] adding virtual IP address pool 'android2': 10.0.0.2/32 08[NET] received packet: from 208.54.35.241[32235] to 96.244.142.28[500] 15[CFG] looking for an ike config for 96.244.142.28...208.54.35.241 15[CFG] candidate: %any...%any, prio 2 15[CFG] candidate: 96.244.142.28...%any, prio 5 15[CFG] found matching ike config: 96.244.142.28...%any with prio 5 01[JOB] next event in 29s 999ms, waiting 15[IKE] received NAT-T (RFC 3947) vendor ID 15[IKE] received draft-ietf-ipsec-nat-t-ike-02 vendor ID 15[IKE] received draft-ietf-ipsec-nat-t-ike-02\n vendor ID 15[IKE] received draft-ietf-ipsec-nat-t-ike-00 vendor ID 15[IKE] received XAuth vendor ID 15[IKE] received Cisco Unity vendor ID 15[IKE] received DPD vendor ID 15[IKE] 208.54.35.241 is initiating a Main Mode IKE_SA 15[IKE] IKE_SA (unnamed)[1] state change: CREATED => CONNECTING 15[CFG] selecting proposal: 15[CFG] proposal matches 15[CFG] received proposals: IKE:AES_CBC_256/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024, IKE:AES_CBC_256/HMAC_MD5_96/PRF_HMAC_MD5/MODP_1024, IKE:AES_CBC_128/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024, IKE:AES_CBC_128/HMAC_MD5_96/PRF_HMAC_MD5/MODP_1024, IKE:3DES_CBC/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024, IKE:3DES_CBC/HMAC_MD5_96/PRF_HMAC_MD5/MODP_1024, IKE:DES_CBC/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024, IKE:DES_CBC/HMAC_MD5_96/PRF_HMAC_MD5/MODP_1024 15[CFG] configured proposals: IKE:AES_CBC_256/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024, IKE:AES_CBC_128/AES_CBC_192/AES_CBC_256/3DES_CBC/CAMELLIA_CBC_128/CAMELLIA_CBC_192/CAMELLIA_CBC_256/HMAC_MD5_96/HMAC_SHA1_96/HMAC_SHA2_256_128/HMAC_SHA2_384_192/HMAC_SHA2_512_256/AES_XCBC_96/AES_CMAC_96/PRF_HMAC_MD5/PRF_HMAC_SHA1/PRF_HMAC_SHA2_256/PRF_HMAC_SHA2_384/PRF_HMAC_SHA2_512/PRF_AES128_XCBC/PRF_AES128_CMAC/MODP_2048/MODP_2048_224/MODP_2048_256/MODP_1536/MODP_4096/MODP_8192/MODP_1024/MODP_1024_160 15[CFG] selected proposal: IKE:AES_CBC_256/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024 15[NET] sending packet: from 96.244.142.28[500] to 208.54.35.241[32235] 04[NET] sending packet: from 96.244.142.28[500] to 208.54.35.241[32235] 15[MGR] checkin IKE_SA (unnamed)[1] 15[MGR] check-in of IKE_SA successful. 08[NET] received packet: from 208.54.35.241[32235] to 96.244.142.28[500] 08[NET] waiting for data on sockets 07[MGR] checkout IKE_SA by message 07[MGR] IKE_SA (unnamed)[1] successfully checked out 07[NET] received packet: from 208.54.35.241[32235] to 96.244.142.28[500] 07[LIB] size of DH secret exponent: 1023 bits 07[IKE] remote host is behind NAT 07[IKE] sending cert request for "C=CH, O=strongSwan, CN=strongSwan CA" 07[ENC] generating NAT_D_V1 payload finished 07[NET] sending packet: from 96.244.142.28[500] to 208.54.35.241[32235] 07[MGR] checkin IKE_SA (unnamed)[1] 07[MGR] check-in of IKE_SA successful. 04[NET] sending packet: from 96.244.142.28[500] to 208.54.35.241[32235] 08[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 10[IKE] ignoring certificate request without data 10[IKE] received end entity cert "C=CH, O=strongSwan, CN=client" 10[CFG] looking for XAuthInitRSA peer configs matching 96.244.142.28...208.54.35.241[C=CH, O=strongSwan, CN=client] 10[CFG] candidate "android-hybrid", match: 1/1/2/2 (me/other/ike/version) 10[CFG] candidate "android2", match: 1/20/5/1 (me/other/ike/version) 10[CFG] selected peer config "android2" 10[CFG] certificate "C=CH, O=strongSwan, CN=client" key: 2048 bit RSA 10[CFG] using trusted ca certificate "C=CH, O=strongSwan, CN=strongSwan CA" 10[CFG] checking certificate status of "C=CH, O=strongSwan, CN=client" 10[CFG] ocsp check skipped, no ocsp found 10[CFG] certificate status is not available 10[CFG] certificate "C=CH, O=strongSwan, CN=strongSwan CA" key: 2048 bit RSA 10[CFG] reached self-signed root ca with a path length of 0 10[CFG] using trusted certificate "C=CH, O=strongSwan, CN=client" 10[IKE] authentication of 'C=CH, O=strongSwan, CN=client' with RSA successful 10[ENC] added payload of type ID_V1 to message 10[ENC] added payload of type SIGNATURE_V1 to message 10[IKE] authentication of 'C=CH, O=strongSwan, CN=vpn.strongswan.org' (myself) successful 10[IKE] queueing XAUTH task 10[IKE] sending end entity cert "C=CH, O=strongSwan, CN=vpn.strongswan.org" 10[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 04[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 10[IKE] activating new tasks 10[IKE] activating XAUTH task 10[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 04[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 01[JOB] next event in 3s 999ms, waiting 10[MGR] checkin IKE_SA android2[1] 10[MGR] check-in of IKE_SA successful. 08[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 08[NET] waiting for data on sockets 12[MGR] checkout IKE_SA by message 12[MGR] IKE_SA android2[1] successfully checked out 12[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 12[MGR] checkin IKE_SA android2[1] 12[MGR] check-in of IKE_SA successful. 08[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 16[MGR] checkout IKE_SA by message 16[MGR] IKE_SA android2[1] successfully checked out 16[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 08[NET] waiting for data on sockets 16[IKE] XAuth authentication of 'android' successful 16[IKE] reinitiating already active tasks 16[IKE] XAUTH task 16[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 04[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 16[MGR] checkin IKE_SA android2[1] 01[JOB] next event in 3s 907ms, waiting 16[MGR] check-in of IKE_SA successful. 08[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 09[MGR] checkout IKE_SA by message 09[MGR] IKE_SA android2[1] successfully checked out 09[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] .8rS 09[IKE] IKE_SA android2[1] established between 96.244.142.28[C=CH, O=strongSwan, CN=vpn.strongswan.org]...208.54.35.241[C=CH, O=strongSwan, CN=client] 09[IKE] IKE_SA android2[1] state change: CONNECTING => ESTABLISHED 09[IKE] scheduling reauthentication in 3409s 09[IKE] maximum IKE_SA lifetime 3589s 09[IKE] activating new tasks 09[IKE] nothing to initiate 09[MGR] checkin IKE_SA android2[1] 09[MGR] check-in of IKE_SA successful. 09[MGR] checkout IKE_SA 09[MGR] IKE_SA android2[1] successfully checked out 09[MGR] checkin IKE_SA android2[1] 09[MGR] check-in of IKE_SA successful. 01[JOB] next event in 3s 854ms, waiting 08[NET] waiting for data on sockets 08[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 14[MGR] checkout IKE_SA by message 14[MGR] IKE_SA android2[1] successfully checked out 14[NET] received packet: from 208.54.35.241[35595] to 96.244.142.28[4500] 14[IKE] processing INTERNAL_IP4_ADDRESS attribute 14[IKE] processing INTERNAL_IP4_NETMASK attribute 14[IKE] processing INTERNAL_IP4_DNS attribute 14[IKE] processing INTERNAL_IP4_NBNS attribute 14[IKE] processing UNITY_BANNER attribute 14[IKE] processing UNITY_DEF_DOMAIN attribute 14[IKE] processing UNITY_SPLITDNS_NAME attribute 14[IKE] processing UNITY_SPLIT_INCLUDE attribute 14[IKE] processing UNITY_LOCAL_LAN attribute 14[IKE] processing APPLICATION_VERSION attribute 14[IKE] peer requested virtual IP %any 14[CFG] assigning new lease to 'android' 14[IKE] assigning virtual IP 10.0.0.2 to peer 'android' 14[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 14[MGR] checkin IKE_SA android2[1] 14[MGR] check-in of IKE_SA successful. 04[NET] sending packet: from 96.244.142.28[4500] to 208.54.35.241[35595] 08[NET] waiting for data on sockets 01[JOB] got event, queuing job for execution 01[JOB] next event in 91ms, waiting 13[MGR] checkout IKE_SA 13[MGR] IKE_SA android2[1] successfully checked out 13[MGR] checkin IKE_SA android2[1] 13[MGR] check-in of IKE_SA successful. 01[JOB] got event, queuing job for execution 01[JOB] next event in 24s 136ms, waiting 15[MGR] checkout IKE_SA 15[MGR] IKE_SA android2[1] successfully checked out 15[MGR] checkin IKE_SA android2[1] 15[MGR] check-in of IKE_SA successful.

    Read the article

  • Setup Reverse DNS with Cpanel and WHM?

    - by m3d
    I needed to set-up a reverse DNS via cpanel. I followed the steps in this tutorial but it didn't work: http://docs.cpanel.net/twiki/bin/view/11_30/WHMDocs/RdnsForBind. I use my own name servers registered with go-daddy. But I am with VPS hosting company. I did use a new serial number and exactly as the tutorial however didnt seems to be working When I check this via windows nslookup {ip-address} I still get the my hosting company name, when reversed.

    Read the article

  • A Variety Of Ways To Use Reverse Email Search

    If you have not heard about reverse email search, you may be wondering exactly what you can use this service for. You can use this search to lookup an email address and find out who it belongs to. Th... [Author: Ed Opperman - Computers and Internet - April 10, 2010]

    Read the article

  • Reverse X11 forwarding

    - by Oli
    I was playing with my phone (that runs a Linux/X stack) last night and I managed to ssh into my desktop and run an application and have it show up on my phone. It was awesome. Today I'd like to sort of do the opposite. I want to view an application running on my phone on my PC. I could install a SSH server on my phone but I frankly don't fancy that purely for security reasons. I want this to be initiated from my phone. Is there a way to connect from my phone and tunnel the PC's X connection back to the phone and then run an application on the phone that show on the PC?

    Read the article

  • How would I setup reverse DNS for 2 email servers?

    - by Solignis
    I have an interesting DNS question (well interesting to me atleast). I just installed an hmail server in our remote office to act as an MX backup in the event our exchange server goes down. The 2 host names are mail.campbellsurvey.com mail2.campbellsurvey.com mail points to the address 98.XXX.91.XXX mail2 points to the address 70.XXX.190.XXX How would I setup a PTR record on the ISP end to reflect both hostnames? Does the PTR have to point to EXACTLY mail.campbellsurvey.com or can it point to just campbellsurvey.com? because right now anything passing through the primary static address in our pool (the one used for standard internet) is identified as mail.campbellsurvey.com. My only idea to fix this was to move the mail server to the next available address and give it only it the name mail.campbellsurvey.com but I wanted to see if there was another way. Thanks in advance.

    Read the article

  • Reverse rdesktop or VNC overlay image!

    - by carlesso
    Hi all. I've got a central server (linux based) and many clients (Windows XP Embedded, afaik) in public places around my country. I need to have these clients to connect to the server with a "reverse" tunnel, that is to say that I need to control the clients from the server but the connection is initialized by clients. The requirement is that, during the connection, an overlay image (or something like that, like a modified version of login screen) is displayed. Some stuff like "Work In Progress". My first idea was to use vncviewer -listen and vnc in reverse mode, but cannot understand how to obfuscate the work I'm doing. Other idea was to use rdesktop in "reverse" mode, but it seems it does not support it. Using rdekstop reverse seems the nicest solution (I can login back the user was in before connection, the login manager - which I can modified - is displayed), but any hint will be appreciated! Thanks in advance!

    Read the article

  • How do I know if have RSI or carpal tunnel?

    - by saniul
    I feel that this is a much better place to ask this than a medical forum, we have ~250 people who spent most of their day in front of a computer. Does anyone here have any experience with such injuries? How/when did you find out? What did you do (if anything)? I don't know if I have the RSI, but I can tell you that I can "crack" my wrist and almost any one of my fingers whenever I want. Also, my wrist sometimes hurts me when I type for a very long time (especially on a laptop keyboard I have very long fingers so the palm is in an uncomfortable position most of the time) Is this normal? I bought a Logitech Wave keyboard, obviously it feels much better than the laptop keyboard, but I can't really tell if it helps the "cracking" and my wrist still sometimes hurts.

    Read the article

  • Something is wrong with this C code to reverse string, but I dont know what ? please help

    - by Harbhag
    Hi all, I am beginnner to programming. I wrote this little program to reverse a string. But if I try to reverse a string which is less than 5 characters long then it gives wrong output. I cant seem to find whats wrong. #include<stdio.h> #include<string.h> int main() { char test[50]; char rtest[50]; int i, j=0; printf("Enter string : "); scanf("%s", test); int max = strlen(test) - 1; for ( i = max; i>=0; i--) { rtest[j] = test[i]; j++; } printf("Reversal is : %s\n", rtest); return 0; }

    Read the article

  • how to add a REverse PTR Record on Amazon Route 53?

    - by Oscar Cabrero
    if i have the below ip 168.144.254.X and i would like to add a ptr record in amazon in the form of X.254.144.168.in-addr.arpa what should be in the name field and what should be in the value field i have a zone created with a name like mydomain.com which host the DNS records for my ip. amazon wont let me add a value of X.254.144.168.in-addr.arpa in the name field do i need to create a new zone for the ip in order to allow this?

    Read the article

  • How many reverse proxies (nginx, haproxy) is too many?

    - by Alysum
    I'm setting up a HA (high availability) cluster using nginx, haproxy & apache. I've been reading great things about nginx and haproxy. People tend to choose one or the other but I like both. Haproxy is more flexible for load balancing than nginx's simple round robin (even with the upstream-fair patch). But I'd like to keep nginx for redirecting non-https to https among other things right at the point of entry to the cluster. On the other hand, nginx is a lot faster for serving static contents and would reduce the load on the powerful apache which loves to eat a lot of RAM! Here is my planned setup: Load balancer: nginx listens on port 80/443 and proxy_forwards to haproxy on 8080 on the same server to load balance between the multiple nodes. Nodes: nginx on the node listens to requests coming from haproxy on 8080, if the content is static, serve it. But if it's a backend script (in my case PHP), proxy forward to apache2 on the same node server listenning on a different port number. Technically this setup works but my concerns are whether having the requests going through several proxies is going to slow down requests? Most of the requests will be PHP requests as the backends are services (which means groing from nginx - haproxy - nginx - apache). Thoughts? Cheers

    Read the article

  • Ubuntu Pound Reverse Proxy Load Balancing Based off active server load?

    - by Andrew
    I have Pound installed on a loadbalancer. It seems to work okay, except that it randomly assigns the backend server to forward the request to. I've put 1 backend machine under so much load that it went into using swap, and I can't even ssh into it to test this scenareo. I would like the loadbalancer to realize that the machine is overloaded, and send it to a different backend machine. However it doesn't. I've read the man page and it seems like the directive "DynScale 1" is what would monitor this, but it still redirects to the overloaded server. I've also put in "HAport 22" to the backend figuring since I can't ssh in, neither could the loadbalancer and it would consider the backend server dead until it gets rid of the load and responds, but that didn't help either. If anyone could help with this, I'd appreciate it. My current config is below. ###################################################################### ## global options: User "www-data" Group "www-data" #RootJail "/chroot/pound" ## Logging: (goes to syslog by default) ## 0 no logging ## 1 normal ## 2 extended ## 3 Apache-style (common log format) LogLevel 3 ## check backend every X secs: Alive 5 DynScale 1 Client 1200 TimeOut 1500 # poundctl control socket Control "/var/run/pound/poundctl.socket" ###################################################################### ## listen, redirect and ... to: ## redirect all requests on port 80 to SSL ListenHTTP Address 192.168.1.XX Port 80 Service Redirect "https://xxx.com/" End End ListenHTTPS Address 192.168.1.XX Port 443 Cert "/files/www.xxx.com.pem" Service BackEnd Address 192.168.1.1 Port 80 HAport 22 End BackEnd Address 192.168.1.2 Port 80 HAport 22 End End End

    Read the article

  • Code understanding, reverse engineering, best concepts and tools. Java.

    - by core07
    One of most demanding tasks for any programmer, architect is understanding other's code. E.g. I am contractor, hired to rescue some project very quickly. Fix bugs, plan global refactoring and therefore I need most efficient way to understand the code. What is the list of concepts, their priority and best tools for this? Of what I know: reverse code engineering to create object models (creating of diagram per package is not so convenient), create sequence diagrams (the tool connects in debug mode to the system and generates diagrams from runtime). Some visualizing techniques, using some tools to work not just with .java but also with e.g. JPA implementors like Hibernate. Generate diagram for not all the codebase, but add some class and then classes used by it. Is Sparx Enterprise Architect state of the art in reverse engineering or far from that. Any other better tools? Ideally would be that tool makes me understand the code as if I wrote it myself :)

    Read the article

  • Time-Machine backup over SSH tunnel to NFS mount

    - by BTZ
    I've recently started using a new NAS which runs CentOS 6.2. One of the purposes of the NAS would be to serve as a backup target. Whilst I have been using Apple's Time-Machine for a while and I am very satisfied with it, I'd like to continue using it. Backing up directly to an address in my network is no hassle; all works fine. For security reasons I'd like all my traffic to go through an ssh tunnel to the NAS. This way I can avoid needing to get a VPNserver (for personal reasons). As of NFSv4 the NFS deamon is bound to port 2049, which makes it easy for me to direct all traffic through a ssh tunnel. Tunnel: ssh -f admin@ms -L 2000:localhost:2049 -N Mount: mount -t nfs -o nfsvers=4,rw,proto=tcp,sync,intr,hard,timeo=600,retrans=10,wsize=32768,rsize=32768,port=2000 localhost:/mac_backup /Volumes/backup This works fine for Finder/terminal and throughput is almost equal to direct traffic. (CPU of the NAS does ride high when I reach max bandwidth though) Now the problem: With Time-Machine I can't use the NFS mount point mounted on localhost. TM seems to try to connect to it and then give me a "OSStatus error 65". I also tried using NFSv3 (I correctly forwarded all ports) with no luck. Can anyone shed a light on this and/or give a solution?

    Read the article

  • Nginx Reverse Proxy : post_action if proxy cache hit - Possbile?

    - by anonymous-one
    We have recently found out about nginxes post_action. We were wondering it there was a way to use this directive if a proxy cache hit is made? The flow we were hoping on is as follows: 1) User request comes in 2) If cache HIT goto A / If cache MISS goto B A) 1) Serve Cached Result A) 2) post_action to another url on the backend B) 1) Server request from backend B) 2) Store result from backend Any ideas if this is possible via post_action? Thanks!

    Read the article

  • Int[] Reverse - What does this actually do?

    - by Jamie Dixon
    I was just having a play around with some code in LINQPad and noticed that on an int array there is a Reverse method. Usually when I want to reverse an int array I'd do so with Array.Reverse(myIntArray); Which, given the array {1,2,3,4} would then return 4 as the value of myIntArray[0]. When I used the Reverse() method directly on my int array: myIntArray.Reverse(); I notice that myIntArray[0] still comes out as 1. What is the Reverse method actually doing here?

    Read the article

  • What port should I use for my reverse proxy to Apache 2 from nginx?

    - by meder
    I have nginx setup as the defacto port 80. I want to setup django+mod_wsgi on Apache2. I'm worried if I leave Apache2 as 80 it will cause a conflict. Is it better to avoid the headache and change Apache to a different port? server { listen 80; server_name work.domain.org; access_log /www/work.domain.org/log/access.log; error_log /www/work.domain.org/log/error.log; location / { proxy_pass http://127.0.0.1:8080/; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Magic-Header "secret"; client_max_body_size 10m; } }

    Read the article

  • How do I update my servers' domain name for Reverse DNS?

    - by Jeff
    I'm updating my mail servers' rDNS and I think I have it all figured out except for one thing. When I installed my OS (Debian Etch), the installer asked me to enter the "domain name". Is the "domain name" updated by using the hostname command? If so, which config file(s) are updated when using the hostname command? If not, how do I change my servers' domain name? My current /etc/hosts: 127.0.0.1 localhost 67.228.178.164 mrspock.example-old.com mrspock My current /etc/hostname: mrspock $ hostname -f mrspock.example-old.com I need to update hostname -f to be mrspock.example-new.com.

    Read the article

  • Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

    - by Kevinoid
    Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated.

    Read the article

  • New Secure Website with Apache Reverse Proxy

    - by jtnire
    I wish to set up a new website that will be accessed by users using HTTPS. I think it is good practise to put the "real" web server in a seperate subnet, and then install an Apache Reverse Proxy in a DMZ. My question is, where should I put the SSL cert(s)? Should I a) Use a self-signed cert on the "real" web server, and a proper cert on the reverse proxy? b) Use 2 real certs on both the "real" web server and the reverse proxy? c) Don't use any cert on the "real" web server, and use a proper cert on the reverse proxy? I'd like to use a) or c), if possible. I also don't want anyone's browser complaining of a self-signed cert. Thanks

    Read the article

  • solutions for a webserver dedicated to manage permissions/ACL and (reverse) proxying API servers?

    - by giohappy
    I'm considering various layouts to expose various HTTP API services (running on their own differents servers) through a frontend server dedicated to manage permissions on behalf of the API services. I've considered various options, from the classical ones like Nginx, Apache, etc. to HAProxy, passing by the various Python webserver solutions like Tornado, Twisted (which gives me the opportunity to implement my own ACL system easily). The foundamental feature is high performance and scalability, and the ability to manage fine grained ACL rules (similar to the HAProxy ACL system) I would like to know what is a suggested approach to setup what I need, and if (opne source) ready-to-use solutions are already available dedicated to this.

    Read the article

< Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >