Search Results

Search found 17970 results on 719 pages for 'crystal reports 2008'.

Page 163/719 | < Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >

• Lenovo ThinkServer TS130 1105 - does 32/64 depend on RAM?

  - by Ecnerwal

  Just got in a Lenovo ThinkServer TS130 1105 (Xeon E3-1225V1) and a (new, sealed, holographed, looks legit) copy of Windows Server 2008 32/64 (standard) to run on it for a pretty lightweight job (currently handled, adequately, by a terrifyingly old Optima P4 running Windows 2000 server - really lightweight, but long-past-due for replacement, without any particular need or excuse for server 2012...) The 64 bit disc sits there and does nothing. The 32 bit disc boots. I haven't spotted any mention of this in the TS130 Manual (I have now combed it, and find no mention of a need to populate in pairs - a preferred order to populate in, yes, but no mention of pairs being required) but I begin to wonder if it's due to the fact that the 4GB RAM suppled with it was a single DIMM, rather than a pair. Better for upgrading, but perhaps requiring an upgrade (or sidegrade) right away to install the x64 version?? Anyone know? I tried the 64-bit DVD on a desktop with an AMD Athlon II X4 635 processor which normally runs Windows7 in 64 bit, and it booted up just fine.

  Read the article

• Why does Hyper-V and Windows Backup crash (BSOD) after successfull backup?

  - by Payson Welch

  Hello I am running Server 2008 R2 with a handful of Hyper-V guest nodes. If Windows backup runs without any of the Hyper-V nodes running, the server is fine. If Hyper-V runs a backup while the Hyper-V nodes are running, it is fine until a few minutes after the backup completes, and then it BSODs. The storage location for the backup is iSCSI - I am wondering if anyone has any input on what might be causing this? I don't have the Hyper-V nodes setup on a vlan and there is only one NIC on the server. Is it possible this is a networking / driver issue, and if so how would I reconfigure the networking to fix this?

  Read the article

• Is it possible to use a static IP assigned by my ISP for an offsite web server on a VPS (different ISP)?

  - by NightOwl888

  I have a web server on a Virtual Private Server with a hosting provider. Unfortunately, they are really stingy with IP addresses and I need to run several SSL certificates on my server, so I will need a few more than I have. I have a block of 5 static IP addresses on a business package through a different ISP and I am only using 1 of them for connectivity in the office. What I am wondering is if it is possible to use the 4 unused static IP addresses from this ISP on my VPS, which is hosted by another ISP? The VPS (web server) is running Windows Server 2008 R2 Web Edition. If this can be done, please let me know how to configure it.

  Read the article

• VM clients can not access WAN

  - by Saariko

  I have a new VM host on my network, on a Dell R620. The dedicated iDrac is connected with static IP of: 192.168.3.x NIC #1 is connected to my router The eSXI 5.1 host is with IP of 192.168.3.250 The vSphere appliance has a static IP of 192.168.3.241 All the clients on the new host are in the same network 192.168.3.x All clients are Windows 2008 R2 My problem is that non of the clients can access the WAN. I can't ping anything which is beyond my router. I CAN ping anything within my router, even if it's on a different subnet - 192.168.0.x (Router rules are in tact and working) I can ping the gateway (192.168.3.254) One thing that I checked, and is bothering my (but don't know if it has any relevance) is that on the Host Networking properties, there is a vmnic0 (picture) that shows as if it only recognizes 192.168.0.x network - is that so? The command: route print shows me the following details, where I have a duplicate entry for 0.0.0.0 (and one is wrong) - which is probably also why it's not working

  Read the article

• wildcard host name bindings for multiple subdomains in multiple sites on IIS7 with a single IP address

  - by orca

  Situation: I have a single windows 2008 server with a single public IP address. I have multiple domains with wildcard A records pointing to the single IP address. I need each domain to be hosted by a different web site. (i.e. www.domain1.com by site domain1site) I need domain1.com to act like www.domain1.com I need each site to be able to have multiple subdomains (i.e. www.domain1.com, abc.domain1.com, xyz.domain1.com) Not relevant yet here it goes, I plan to handle each subdomain by a different application hosted in the same site (i.e. application /xyz in domain1site) However I found out that IIS7 does not support creating web sites with wildcard host name binding and setting it without any subdomain (i.e. domain1.com) does not work, even for www.domain1.com. Is there a simple solution? Does any IIS Extension like Application Request Routing provide such capability?

  Read the article

• Merge Publication Data Partition Snapshot generation

  - by David Osborn

  I have a merge publication in SQL 2008 R2 with data partitions and I am wondering when I should generate the snapshots for the data partitions. I get an error sometimes when bringing a new subscribe online related to the partition snapshot being out of date and I am wondering if this has to do with the publication snapshot being scheduled at the same time as the partition snapshots. I'm not really sure how the partition snapshot gets generated, but it appears maybe it is getting generated before the publication snapshot. If this is the case how should I be scheduling the partition snapshots to get generated? Should I set them to run x number of minutes after the publication snapshot? this seems kind of poor to do in case the publication snapshot takes awhile or fails. It seems to me the publication snapshot should just run the data partition snapshot agents when it is done if this is the case.

  Read the article

• Deleting files using .NET that were migrated from win2k3

  - by Andrew Duncan

  We recently migrated an ASP.NET website from Windows 2003 to Windows 2008 R2, by zipping up all the files and extracting them to the new site. Since migrating the web application is still able to upload and delete files (that are new), however, it's unable to delete files that were copied from the original Win 2k3 app. We're guessing it's a permissions problem because the error is: Access to the path 'E:.......PATH.....' is denied. We've been trying to match the permissions of a newly uploaded file to that of a migrated files. Newly uploaded files seem to get the APP POOL user as a permission and the OWNER. However, the original files didn't have this. Any help that anyone can be would be fantastic. Thanks,

  Read the article

• how to warehouse data that is not needed from sql server

  - by I__

  I have been asked to truncate a large table in sql server 2008. The data is not needed but might be needed once every two years. It will NEVER have to be changed, only viewed. The question is, since I don't need the data on a day-to-day basis, what do I do with it to protect and back it up? Please keep in mind that I will need to have it accessible maybe once every two years, and it is FINE for us if the recovery process takes a few hours. The entire table is about 3 million rows and I need to truncate it to about 1 million rows.

  Read the article

• ts_block.vbs and mac intosh

  - by Eric Le breton

  I am using your excellent ts_blocker, release 20120530, on my server 2008 R2 Enterprise. it works very fine, i use the vbs script, launched with wscript. The only problem is that is does not work for users attempting to connect RDP from a mac intosh. With this machine the distant IP seems to be not recognized when the login fails. The IP is visible when the login is good (event ID 4624) but not when it fails (Audit failure event ID 4625) : then the IP is not to be seen in the event log ! In the "network information" of the event log entry is nothing given. Have you already been told of that and is there something to do ?

  Read the article

• Does Apache 2.2 (windows) have any default bandwidth limit?

  - by igino manfre'

  I'm running Apache on a server in cloud (Windows server 2008 R2 on VMware, 1 Gbps of BW, http://95.110.164.61 ). I'm streaming many live DVB MPEG Transport Stream, precompressed in loop, (not flash) generated by VLC on port 640xx and then reverse proxied by Apache on port 80. The server's firewall is open for VLC and Apache on all ports. Above 1.5 Mbps the reproduction is affected by continous stop & go. Please note that if you request a stream generated by VLC directly at http://95.110.164.61:64087/mpg2_6.4 you see a correct stream, while if you request http://95.110.164.61/mpg2_6.4 you do not. I know that Flash streaming Server uses Apache to stream on port 80 (and it works). I'm not an expert with Apache, can anyone tell me if any "special" module is required to increase the bandwidth?

  Read the article

• Asking for Credentials, when requesting shared folders on the server, regularly for domain users?

  - by MFH

  In our network, single domain controller, when some users (members of the domain) request shared folders on the server they are required to enter their credentials, the server is Windows Server 2008 R2, even checking to remember my credentials doesn't work, sometimes it shows this message: "The system has detected a possible attempt to compromise security. Please ensure that you can contact the server that authenticated you", sometimes it shows different messages, when I try to recreate the case sometimes I failed, I searched Google for it, I didn't find useful results, some talk about kerberos, but we don't use kerberos, this keeps going each day or two, how to overcome this, I don't want these messages to appear to users?

  Read the article

• Computer Invisible On Domain

  - by Giawa

  Good afternoon, I'm sorry that this isn't a programming question specifically, but stackoverflow has been great at answering questions in the past, so I thought I'd give it a shot. One of our Linux users attempted to install Cygwin on our Windows Server 2008 Domain Controller. Now it is no longer possible to browse the domain and see all of the computers. For example, \\my_domain_name will just bring up a username/password dialog box (that will not accept any username or password, even the domain administrator) and no computers will ever be listed. However, I can still connect to computers based on their name or IP address. So \\eridanus or \\192.168.1.85 still work to connect to the shared directories of computers on our network. Does anyone know where I can find these settings? and how I can fix this problem? Thanks, Giawa

  Read the article

• How to charge an iPhone on a Windows PC without Installing iTunes

  - by Martin Hollingsworth

  I want to be able to charge my iPhone on my work computer, which is running Windows Server 2008 SP1 64-Bit. When I plug the iPhone in with the USB cable, it will not charge. Windows attempts to locate a driver for the device but only comes up with a generic Camera device and even if I allow that to be installed, the iPhone still does not charge. I have checked the computer's BIOS settings and did not find anything relating to power on the USB devices. I also tried this on ports at the back of the computer in addition to those on the front. The PC is a Dell Optiplex 780. As far as I can tell USB devices do not charge unless Windows has installed an appropriate driver. Since it is a work computer I do not want to install iTunes which does include a driver. I have a workaround that I will post as an answer for reference.

  Read the article

• Dreamweaver not connecting RDC

  - by thomas

  I am trying to use Dreamweaver to Remote Desktop Connect into a computer where a website is hosted. Normal traffic to this server is routed to another domain, but when accessed by IP (it is my understanding) the traffic never hits any sort of nameserver request, and so stays there. This server is set up so that the only way I can access it is RDC. I can connect using an RDC program, but when I attempt to use Dreamweaver, I get a vague error. The desired action could not be completed because an unexpected client/server communication error occurred. I have Web URL as http://my.ip.number/directory And in the settings panel, I have Host name: my.ip.number Port: 3388 Host directory: C:\Program Files (x86)\directory/directory Username: user Password: ••••••• What could be preventing Dreamweaver form connecting? Thanks! SERVER DETAILS It is a virtual server Windows SERVER 2008 R2 Standard Service Pack 1

  Read the article

• How do you expand a raid disk array in a dell 2850?

  - by johnny

  Hi, I have a Dell 2850 and I want to install Windows 2008 Server. Problem is that my C drive only has 16GB of space. The requirements say I need at least 20. I have an open bay for a drive. If I put in another drive, how can I add that to the array and them make it only for the C drive? what do I do? Thank you. edit: I don't want to remove any drives. I just want to add a new one to the existing array. Can I do that and make sure that new drive is for the logical C drive?

  Read the article

• SSH Server Timeout on port 22 but not on higher port

  - by mikelberger

  If I run an SSH server on my Windows 2008 server box on the default port 22 I always get Operation Timed Out on the client. If I run it on another port (say 2222) it works fine. I've opened up the firewall. Netstat shows that the server is listening on the correct port. I have used two different Windows SSH servers (freeSSHd and WinSSHD) and they both have the same result. What else could be causing the difference between running the SSH server on port 22 versus port 2222?

  Read the article

• From which plex am I booted from on raid?

  - by rumburak

  I have a server with mirrored boot volume. It is software raid 1 in Windows Server 2008 R2. I do not have physical access to the server. I am looking for a way to check which disk is a boot drive. I need a way to check it from os. How can I do that ? EDIT: I know how to do that, but I dont think its proper way. From diskpart I can break mirror: select volume 0 break disk=0 And Windows will only allow me to do that on not current boot disk. I want to check which one is boot without breaking mirroring.

  Read the article

• Creating a custom view for windows log based on a "Contains {text}" rule

  - by jussinen

  I have a server running Windows Server 2008. I'm using Windows Server Auditing to check when and by which user a folder is modified to determine who is modifying it as the modifications are causing problems. I can see the log of the audit when a change is made in the System log. How do I create a Custom View that will return all events from System log where a certain text (which is the folder name) is present? The create custom view doesn't seem to have that option. I'm not sure whether it's possible via custom xml query or whether I'll need to export the system log to csv and search in Excel. John

  Read the article

• Which firewall ports do I need to open in order for a domain trust to work?

  - by Massimo

  I have two Active Directory domains in two different forests; each domain has two DCs (all of them Windows Server 2008 R2). The domains are also in different networks, with a firewall connecting them. I need to create a two-way forest trust between the two domains and forest. How do I configure the firewall to allow this? I found this article, but it doesn't explain very clearly which traffic is required between DCs, and which traffic (if any) in needed instead between domain computers in one domain and DCs for the other one. I'm allowed to permit all traffic between the DCs, but allowing computers in one network to access DCs in the other one would be a little more difficult.

  Read the article

• Something is spamming from my hMail server - how can I deal with this?

  - by joshcomley

  My Windows 2008 server is attempting to send out a lot of spam, I've just discovered, and I'm not sure how to see where the compromise is. For example: has someone hacked an account? Has someone hacked the server? Is there a virus on the server? What can I do to investigate this? Edit Thanks for the replies so far. I am running hMail server, and have spent so long investigating the correct configuration but still I end up with these emails being sent. Here is a screenshot of my Internet IP range settings on the server: (let me know what else I can provide to help)

  Read the article

• Default user logon on Windows Server system

  - by Robert Koritnik

  I installed Remote Desktop Services role (ex Terminal Services) on my Windows Server 2008 R2 machine. After installation when I try to logon locally, there's no default user as it used to be. Can I tweak group policy to have my default user back? I did enable to remember last logon user, but it didn't work... Obviously RDS (ex TS) ignores this policy setting. Additional note: I'm not connected to a domain. It's a standalone development machine running server OS. No domain needed for it.

  Read the article

• Host a Debian repository on a Windows Web/Ftp server

  - by Dave

  At the risk of causing a matter vs. antimatter paradox that would end the world as we know it ... Is it possible to host a Debian repository on a Windows server? We have some applications which are available for Windows, Mac OS X, and Linux. Our web site, from where the application can be downloaded, is a Windows Server 2008 box running IIS 7. That is not going to change, and I would like to avoid having to purchase another server and/or domain. I would like to take advantage of the Debian packaging system so that I can just instruct users to add our repository to their software sources, and then they can install, get updates, resolve dependencies (some of which are not yet in the stable/main distributions of my target platforms), etc. The instructions I can find on the internet require linux-specific tools to create a local repository, but are unclear as to whether or not that can be copied to an FTP site as is, or if it requires some local daemons to be running or something.

  Read the article

• Issue with Windows Server backup

  - by mamu

  I have windows server 2008 r2 installed, Only service running on it is hyper-v. I am trying to take backup using windows server backup feature and it fails with following error in eventlog The backup operation that started at '?2009?-?08?-?22T18:42:14.123000000Z' has failed because the Volume Shadow Copy Service operation to create a shadow copy of the volumes being backed up failed with following error code '2155348129'. Please review the event details for a solution, and then rerun the backup operation once the issue is resolved. Above error itself is point to other event logs for more detail but i can't find anything in event logs Then i ran following command vssadmin list writers It had following out of ordinary in list Writer name: 'Microsoft Hyper-V VSS Writer' Writer Id: {66841cd4-6ded-4f4b-8f17-fd23f8ddc3de} Writer Instance Id: {d15c5f78-121c-464f-b23b-f285e919b05c} State: [8] Failed Last error: Inconsistent shadow copy How could i resolve this?

  Read the article

• Strange RDP / Remote Desktop problem

  - by John Landheer

  I'll try to be as specific as I can be: Server is running SBS 2008 R2 (with all updates) Server is connected to the internet Server has 2 NIC's, one is disabled Server is running RDP Service (accessible directly from the internet, I know, not as secure as it should be) Computers A and B are on the same local net. Computers A and B are both Windows 7. Users X and Y are both admins on the server Computer A can connect as user X to the server with mstsc Computer A can connect as user Y to the server with mstsc Computer B can connect as user X to the server with mstsc computer B CANNOT connect as user Y to the server with mstsc! The last point is the problem, I get an authentication error. This used to work flawlessly for the last year. The server and desktops have been rebooted. I find it very strange....

  Read the article

• Enable a program in Windows to run multiple times?

  - by user135490

  I've got this legacy software that only allows you to run one copy at a time, it detects that you have another session opened and it won't allow you to open a second instance. The problem is this is a cpu intensive program and it only use a single core. Is there any hacks or tweaks so I can trick it and open more than one instance? This would allow me to retire about 5 servers... I'm using Windows 2008 R2. I had to use cff explorer to enable the use more than 2GB RAM as the program crashes when it tries to use more than 2GB.

  Read the article

< Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >