Search Results

Search found 13331 results on 534 pages for 'fluent interface'.

Page 163/534 | < Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >

  • Restore access to Cisco Connect after changing router settings

    - by StasM
    I have recently bought Cisco Valet Plus (M20) wireless router (which I recognize now was a mistake, but nevermind). It has two setup options - Cisco Connect software and web-based setup. Cisco Connect software allows changing very small set of settings, web-based setup allows access to almost all settings, except settings for guest network. The problem is that when I use web-based setup, Cisco Connect after some changes refuses to talk to the router, so I can't change guest settings anymore (since web interface doesn't allow to change them). It must be because of some config parameter not matching or some password set wrong - but I don't know where Cisco Connect stores them. So, does anybody have any idea how to make Cisco Connect talk to the router again once I changed the settings through the web interface?

    Read the article

  • Not all events appear in Nagios history (archive)

    - by Lars
    in the "Host & Service history" of my check_mk interface I can see various events, but a lot of events are missing. On the default interface at "View Alert History For This Service" or in the logfiles /var/log/nagios/archives/*.log the same issue: I can see many events of the last days, but not all of them. In the /etc/nagios/nagios.cfg the options log_event_handlers, log_initial_status and log_passive_checks are set to 0, the other log_... options are set to 1. I don't think that any of these options causing the problem that not all events are logged. What could cause this problem?

    Read the article

  • Monitoring ASA packet loss via SNMP

    - by dunxd
    I want to monitor packet loss on my ASA 5505 VPN endpoints using SNMP. This is so I can graph the rates in Cacti and/or get alerts in Nagios. However, I am not sure what SNMP values I should use to measure packet loss. In the ASA I can run sh interface Internet stats to show traffic statistics for the interface connected to the Internet. This shows 1 minute and 5 minute drop rates. Are these measures an indicator of packet loss? Are there SNMP values I can access that correspond to those values? Should I be looking at different values? Is the ASA even able to measure packet loss?

    Read the article

  • Using local proxy to specify used NIC on Windows 7?

    - by Nico
    I'm running Windows 7 and have 2 NIC installed, both are connected to the Internet (nic#1 LTE, nic#2 DSL). Windows 7 will only allow me to specify a binding order and a metric on which interface to chose but i can't specify this on an application level. My Idea was to use a local proxy server and use the proxy server whenever i want to use nic#2. I tried wingate and free proxy, both applications will let me chose the interface i want to use but this setting seems to have no effect? This is how i configured the applications: http://imageshack.us/photo/my-images/69/freeproxysettings.jpg/ http://imageshack.us/photo/my-images/811/wingateproxysettings.jpg/ Is what i'm trying to do in anyway possible?

    Read the article

  • IDE to SATA convertor Motherboard Issue

    - by ravidev
    I bought new motherboard Intel DH67GD which has not IDE interface to attach the DVD writer. It has 2 SATA with 6Gb/s, 3 SATA with 3Gb/s and 1 e-SATA with 3GB/s.(mobo specs link : http://www.intel.in/content/www/us/en/motherboards/desktop-motherboards/desktop-board-dh67gd.html) Can anyone tell me how can i connect my old LG DVD Writer(IDE interface) with Mobo ?? Will IDE to SATA Connector work? If yes then how to connect that DVD writer with IDE-SATA converter? Please provide link. Thanks in advance !!

    Read the article

  • Chain Gateways on the LAN

    - by Black2night
    I installed m0n0wall in a virtualized environment, i have 10 PCs connected to a router ( 192.168.1.0/24) which connect them to the internet through PPPoE, the problem is that this router does not have a QoS so what i want to do is the following :- let all the PCs get their IP from the Router and the default gateway will be m0n0wall the moon wall will have 2 interface (Lan 192.168.1.20) and (Wan 192.168.1.21 and default gateway 192.168.1.1) now when any PC want to access the internet it should go through m0n0wall and then m0n0wall will forward the connection to the default gateway through the wan interface which is the PPPoE running on the router (192.168.1.1) the big question is this scenario possible or not and what do you suggest? Thanks

    Read the article

  • How to correctly set up iWARP? Preferably on loopback

    - by ajdecon
    iWARP is a protocol for doing remote direct memory access (RDMA) on top of TCP/IP, so that it can work with Ethernet and other network types as opposed to Infiniband. It works with many of the standard IB interfaces - the IB verbs, for example - so it's all pretty transparent. I'm doing some IB-verbs programming (mostly for the sake of learning about how they work better), and it'd be wonderfully convenient for me if I could use iWARP to do RDMA over my loopback interface, so that I could test some of my code without getting on our IB-connected cluster. :-) But I cannot figure out how to get a "local development environment" set up: there are no tutorials I'm aware of for even setting up iWARP from scratch on a server or a network interface. Can anyone give me a tutorial or point me in the right direction? Environment is Fedora 16 running in VirtualBox.

    Read the article

  • Citrix XenApp application does not have keyboard focus when launched

    - by Jason Pearce
    On new or existing Citrix XenApp 4.5 servers, I am having problems streaming the Allscripts Pro EHR application via the XenApp web interface. When users launch the application via the Citrix XenApp web interface, the application does not have focus, preventing users from typing in their username and password. If they use their mouse to select either the username or password fields, they still cannot enter any text. However, if they do any of the following actions, they can then enter in their username and password and the application runs without problems: Click on the Login button with empty fields. Logon fails but they can then enter their credentials. Minimize the login window and then maximize it. They can then gain keyboard focus to enter their credentials. What might be preventing this particular application from having focus when it launches?

    Read the article

  • Cisco 877 as PPPoA/PPPoE bridge (no routing) - how to make it listen to IP for management?

    - by Ingmar Hupp
    I have a Cisco 877 configured to bridge ADSL with PPPoA to PPPoE on Vlan1. This works fine, but in this mode the only way I can configure the Cisco is via the serial console. I'd like to have the Cisco also listen on an IP address so I can telnet/ssh into it. I think the right way to go about this would be via bridge irb, but I'm not sure exactly how (or if that's even the right direction). IOS is 12.4T and my current config (cut down to essentials) is: no ip routing no ip cef ! ! interface ATM0 no ip address no ip route-cache no atm ilmi-keepalive pvc 0/38 encapsulation aal5snap ! dsl operating-mode auto bridge-group 1 ! ! interface Vlan1 no ip address no ip route-cache bridge-group 1 Just setting an IP address on Vlan1 didn't have the desired effect, but surely this must be possible somehow (the Draytek Vigor 120 even does it by default).

    Read the article

  • Why do I have to manually 'Restart Management Network' on vSphere 5 host after reboot to get networking available?

    - by growse
    I've got a couple of vSphere 5.0 hosts in a small lab environment here and I've noticed a strange behaviour. When on of the hosts gets rebooted, it is unresponsive to the network until I log into the ESX console, Press F2 to customize and select Restart management network. Once this is done, the networking works perfectly as expected. Each host has two NICs which are trunked together using Etherchannel to a Cisco 3750. The link is also a .1q VLAN trunk and the management network is configured on VLAN121 with the VM traffic configured on VLAN118. Why would the host be completely dead to the world until I physically kick it? Edit Sample switch config for trunk: interface Port-channel2 description Blade 1 EtherChannel Trunk switchport trunk encapsulation dot1q switchport mode trunk end ! ! interface GigabitEthernet4/0/1 description Bladecenter1 CPM 1A switchport trunk encapsulation dot1q switchport mode trunk speed 1000 duplex full channel-group 2 mode on end Vswitch teaming settings: Management port group settings:

    Read the article

  • Basic networking: Centos Server Router + Ubuntu Client setup.. unable to access outside world from client

    - by ale
    I am trying to set up my Centos Server with two NICs as a router. eth0 is connected to the outside world and eth1 is connected to an Ubuntu client. Here's eth0 on the server: DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=yes TYPE=Ethernet eth1 on the server: DEVICE=eth1 BOOTPROTO=static IPADDR=192.168.0.10 # a free address on my network ONBOOT=yes TYPE=Ethernet My server has IPv4 packet forwarding turned on and my iptables only contains: # iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE # iptables --append FORWARD --in-interface eth1 -j ACCEPT My Ubuntu client has this in its /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp gateway 192.168.0.10 but I can't get an Internet connection from the server for my client. I can't even ping my server from the client: $ ping 192.168.0.10 Destination Host Unreachable

    Read the article

  • Trixbox CentOS Default GW Problem (Multi-homed server)

    - by slashp
    I'm having an issue with a CentOS trixbox server which is dual-homed (one private facing NIC [eth1], one internet-facing NIC [eth0]). I can't seem to get the default gateway to set properly to our ISP's GW via eth0. I've modified the /etc/sysconfig/network to contain both a GATEWAY & GATEWAYDEV line and removed the GATEWAY line from /etc/sysconfig/network-scripts/ifcfg-eth1 (as well as /etc/sysconfig/network-scripts/ifcfg-eth0). No default GW shows up in the routing table unless it's specified in the ifcfg-eth1 file (which both the wrong interface and wrong gateway IP), otherwise, the routing table simply does not contain a default gateway..any ideas would be greatly appreciated! Thanks! EDIT Just realized when attempting to add the default gateway manually using the route add command, I receive an error stating: SIOCADDRT: Network is unreachable I know this error can occur when your default gateway and interface IP address are not on the same subnet..in this case, my public IP address of eth0 is a /29.

    Read the article

  • Windows Phone 8 not interfacing with Zune software

    - by Cyberherbalist
    I just got a Lumia 521 with Windows Phone 8 and am trying to get the device to work with the Zune software on my PC. I still have my Windows Phone 7 device, and the new one is not working the same way. When I plug the WP7 device into the PC's USB port, it automatically fires up Zune and I can sync my podcasts and music etc to the device. But when I plug the Lumia into the PC it doesn't fire up Zune, and if I start Zune manually, it doesn't interface with the phone at all. Perhaps I am missing something and WP8 isn't supposed to use Zune to interface with the phone?

    Read the article

  • Where is debian storing its network settings?

    - by user13743
    I have a debian machine that is supposed to have a static ip, but insists on getting its address from the DHCP server. Here's this settings file: $> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 192.168.1.99 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 Yet $> sudo /etc/init.d/networking restart Reconfiguring network interfaces...done. $> sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:e0:03:09:05:2e inet addr:192.168.1.205 Bcast:255.255.255.255 Mask:255.255.255.0 ... Where is it being told to use dhcp?

    Read the article

  • How to get rid of NAT in a LAN?

    - by Alberto
    Currently the LAN I manage is organized as follows: internal network (192.168.1.0) which uses a Linux server as a gateway (internal address on interface br0 192.168.1.1, external address on interface br1 10.0.0.2) through NAT; then the 10.0.0.0 network has another gateway (10.0.0.1) which through another NAT connects the whole thing to the internet. What I would like to achieve is to configure the Linux server so that the first layer of NAT is no more necessary, so that for example a computer in the 10.0.0.0 network can ping every computer in the 192.168.1.0 network. I deleted this iptables rule: iptables -t nat -A POSTROUTING -o br1 -j SNAT --to-source 10.0.0.2, but of course now computers on 192.168.1.0 cannot reach the internet; ip forwarding is of course enabled. What's missing here? Thanks

    Read the article

  • Proxy Error 502 "Reason: Error reading from remote server" with Apache 2.2.3 (Debian) mod_proxy and Jetty 6.1.18

    - by Martin
    Apache is receiving requests at port :80 and proxying them to Jetty at port :8080 The proxy server received an invalid response from an upstream server The proxy server could not handle the request GET /. My dilemma: Everything works fine normally (fast requests, few seconds or few tens of seconds long requests are processed ok). Problems occur when request processing takes long (few minutes?). If I issue request instead directly to Jetty at port :8080 the request is processed OK. So problem is likely to sit somewhere between Apache and Jetty where I am using mod_proxy. How to solve this? I have already tried some "tricks" related to KeepAlive settings, without luck. Here is my current configuration, any suggestions? #keepalive Off ## I have tried this, does not help #SetEnv force-proxy-request-1.0 1 ## I have tried this, does not help #SetEnv proxy-nokeepalive 1 ## I have tried this, does not help #SetEnv proxy-initial-not-pooled 1 ## I have tried this, does not help KeepAlive 20 ## I have tried this, does not help KeepAliveTimeout 600 ## I have tried this, does not help ProxyTimeout 600 ## I have tried this, does not help NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] ServerName www.mydomain.fi ServerAlias mydomain.fi mydomain.com mydomain www.mydomain.com ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests Off ProxyPass / http://www.mydomain.fi:8080/ retry=1 acquire=3000 timeout=600 ProxyPassReverse / http://www.mydomain.fi:8080/ RewriteEngine On RewriteCond %{SERVER_NAME} !^www\.mydomain\.fi RewriteRule /(.*) http://www.mydomain.fi/$1 [redirect=301L] ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On </VirtualHost> Here is also the debug log from a failing request: 74.125.43.99 - - [29/Sep/2010:20:15:40 +0300] "GET /?wicket:bookmarkablePage=newWindow:com.mydomain.view.application.reports.SaveReportPage HTTP/1.1" 502 355 "https://www.mydomain.fi/?wicket:interface=:0:2:::" "Mozilla/5.0 (Windows; U; Windows NT 6.1; fi; rv:1.9.2.10) Gecko/20100914 Firefox/3.6.10" [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: error reading status line from remote server www.mydomain.fi, referer: https://www.mydomain.fi/?wicket:interface=:0:2::: [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: Error reading from remote server returned by /, referer: https://www.mydomain.fi/?wicket:interface=:0:2:::

    Read the article

  • Bind telnetd to specific IP on AIX 5.3?

    - by Sama
    Is it possible to bind telnetd to a specific IP on AIX 5.3? I know telnet is evil. Unfortunately, we have to have it listening on one interface for a specific application, but I want to make sure that's the only interface/IP that it's listening on. I have been searching all over the net and have found some advice for Linux, but it doesn't appear to be applicable to AIX. Full disclosure: I am not the server admin, but I am working closely with them and am familiar with *nix. Add: This is an internal server, which is connected to two different vlans. This is NOT connected to the Internet(!).

    Read the article

  • ASA firewalls: how does stateful filtering affect my access lists?

    - by Nate
    Ok, so assume that I have an ingress access list that looks like this: access-list outside_in extended ip permit any X.Y.Z.1 eq 25 access-group outside_in in interface outside And I want to do egress filtering. I want to allow inside machines to respond on port 80, and I want to allow ports over 1024. Given that the firewall is statefull, do I need to have the rule access-list inside_in extended ip permit X.Y.Z.1 any eq 25 in my inside_in ACL, or can I get away with just access-list inside_in extended ip permit any any gt 1024 access-group inside_in in interface inside In other words, if I apply an egress access list, do I have to explicitly allow machines to respond to requests allowed by the ingress access list, or does the statefullness of the firewall handle that for me? Thanks!

    Read the article

  • Setting a wireless access point on Ubuntu server 11.10

    - by Solignis
    I am trying to setup a wifi access point with my Ubuntu server. I have managed to get my phone to connect the wireless and now it get a DHCP lease. Though it still cannot ping out or get pinged by anything on my network. I am prety sure my problem is iptables, but I not sure what would be wrong. Here is what my rules look like. (The ones pertaining to the bridge interface) # Allow traffic to / from wireless bridge interface iptables -A INPUT -i br0 -j ACCEPT iptables -A OUTPUT -o br0 -j ACCEPT I am guessing my rules are a little lean, the bridge exists on the same subnet as everything else on my network, I am using a 10.0.0.0/24 subnet. EDIT Oh yeah I should mention also, when I do a ping test, I get Destination Host Unreachable as the error.

    Read the article

  • routing through multiple subinterfaces in debian

    - by Kstro21
    my question is as simple as the title, i have a debian 6 , 2 NICs, 3 different subnets in a single interface, just like this: auto eth0 iface eth0 inet static address 192.168.106.254 netmask 255.255.255.0 auto eth0:0 iface eth0:0 inet static address 172.19.221.81 netmask 255.255.255.248 auto eth0:1 iface eth0:1 inet static address 192.168.254.1 netmask 255.255.255.248 auto eth1 iface eth1 inet static address 172.19.216.3 netmask 255.255.255.0 gateway 172.19.216.13 eth0 is conected to a swith with 3 differents vlans, eth1 is conected to a router. No iptables DROP, so, all traffic is allowed. Now, passing the traffic through eth0 is OK, passing the traffic through eth0:0 is OK, but, passing the traffic through eth0:1 is not working, i can ping the ip address of that sub interface from a pc where this ip is the default gateway, but can't get to servers in the subnet of the eth1 interface, the traffic is not passing, even when i set the iptables to log all the traffic in the FORWARD chain and i can see the traffic there, but, the traffic is not really passing. And the funny is i can do any the other way around, i mean, passing from eth1 to eth0:1, RDP, telnet, ping, etc, doing some work with the iptable, i manage to pass some traffic from eth0:1 to eth1, the iptables look like this: iptables -t nat PREROUTING -d 192.168.254.1/32 -p tcp -m multiport --dports 25,110,5269 -j DNAT --to-destination 172.19.216.1 iptables -t nat PREROUTING -d 192.168.254.1/32 -p udp -m udp --dport 53 -j DNAT --to-destination 172.19.216.9 iptables -t nat PREROUTING -d 192.168.254.1/32 -p tcp -m tcp --dport 21 -j DNAT --to-destination 172.19.216.11 iptables -t nat POSTROUTING -s 172.19.216.0/24 -d 172.19.221.80/29 -j SNAT --to-source 172.19.221.81 iptables -t nat POSTROUTING -s 172.19.216.0/24 -d 192.168.254.0/29 -j SNAT --to-source 192.168.254.1 iptables -t nat POSTROUTING -s 172.19.216.0/24 -o eth0 -j SNAT --to-source 192.168.106.254 dong this is working, but,it is really a headache have to map each port with the server, imagine if i move the service from server, so, now i have doubts: can debian route through multiple subinterfaces?? exist a limit for this?? if not, what i'm doing wrong when i have the same setup with other subnets and it is working ok?? without the iptables rules in the nat, it doesn't work thanks and i hope good comments/answers

    Read the article

  • VLC without chrome in Windows

    - by timberwo7ves
    I'm trying to run VLC (2.1, 64 bit) without any chrome on Windows 7. You can achieve it by going to Preferences, and in the Interface tab, unchecking Integrate video in interface, and also in the Video tab, unchecking Window decorations. The problem lies in the fact that without Window decorations there is no apparent way to move or resize the video window - in GOM player, for example, you can move window by dragging on the video itself; is there an option for this in VLC? Ideally, I would like to move the window by the method described above (by dragging the video), and would like the Window decorations to reappear on mouseover, to allow resizing; I'm a new VLC user, but unsure how far the customisation goes. - I'd settle with just the moving of the window via dragging the video if this is possible by advanced setting. There is a similar question here, but not exactly, and no solution to that particular question.

    Read the article

  • backup sql databases, folders; 7ZIP and copy to ftp

    - by laurens
    Hi all, We are quite stuck with which solution to choose for this backup issue: What should happen: First, there should be an interface were to choose several sql databases (sort of checkboxes or whatsoever), also a few folders should be backed up - this could be part of the program or could be seperate, I think about an interface were to select folders, but a txt file (or xml) with paths-to-folders is as good. Next, everything should be 7Zipped, SQL-DB and files seperate. Eventually everything should be copied to a local network drive after which copied via FTP. Also important; it could be programmed or (partly) bought but I can't be one of those expensive backup tools $1000+ etc. I already found this fairly priced tool that does already most of the tasks 7ZIP and copy to ftp sqlbackupandftp.com For your information: we had a kind of self-made tool created by a collegue (some time ago) but it became very untrustworthy and as the databases grew it couldn't handle it anymore... moving on Please come up with suggestions. Thanks in advance!

    Read the article

  • VSTS2010 crashes on opening the team explorer->My queries node

    - by vstsuser
    VSTS2010 crashes on opening the team explorer-My queries node this does not repeat if MSN office communicator (2007 R2 version) is exited. the issue occurs only if MSN office communicator is up and running. (no issues reported by communicator though) Any help in this regard? Debug log: Unable to cast COM object of type 'CommunicatorAPI.MessengerClass' to interface type 'MessengerAPI.IMessenger2'. This operation failed because the QueryInterface call on the COM component for the interface with IID '{....}' failed due to the following error: Error loading type library/DLL. (Exception from HRESULT: 0x80029C4A (TYPE_E_CANTLOADLIBRARY)). Windows event log EventType clr20r3, P1 devenv.exe, P2 10.0.30319.1, P3 4ba1fab3, P4 microsoft.teamfoundation.collaboration.microsoft, P5 10.0.0.0, P6 4c7d8ce4, P7 49, P8 0, P9 system.invalidcastexception, P10 NIL.

    Read the article

  • Linux QoS: bulk data transmission during idle times

    - by syneticon-dj
    How would I do a QoS setup where a certain low-priority data stream would get up to X Mbps of bandwidth, but only if the current total bandwidth (of all streams/classes) on this interface does not exceed X? At the same time, other data streams / classes must not be limited to X. The use case is an ISP billing the traffic by calculating the bandwidth average over 5 minute intervals and billing the maximum. I would like to keep the maximum usage to a minimum (i.e. quench the bulk transfer during interface busy times) but get the data through during idle/low traffic times. Looking at the frequently used classful schedulers CBQ, HTB and HSFC I cannot see a straightforward way to accomplish this.

    Read the article

  • Help with OpenVPN setup on Windows Server 2003

    - by Bill Johnson
    Hi all, Just wondering if someone can assist me further with the set-up of OpenVPN on my Windows Server 2003. I have configured Win Server as per the following guide: http://tinyurl.com/kxusv and I'm now at the stage of Creating the config files. I have a few questions that I need some assistance with. My server IP is 192.168.1.10 and my routers IP address is 192.168.1.1 (the router is a Netgear DGN2000). I have edited the server.ovpn file as per the following: push "dhcp-option DNS X.X.X.X" # Replace the Xs with the IP address of the DNS for your home network (usually your ISP's DNS) push "dhcp-option DNS X.X.X.X" # A second DNS server if you have one to include my ISP DNS and I have not edited anything else. Now my issue is with the client1.opvpn file as per the below: client dev tap #dev-node MyTAP #If you renamed your TAP interface or have more than one TAP interface then remove the # at the beginning and change "MyTAP" to its name proto udp remote YOURHOST.dyndns.org 1194 #You will need to enter you dyndns account or static IP address here. The number following it is the port you set in the server's config route 192.168.1.0 255.255.255.0 vpn_gateway 3 #This it the IP address scheme and subnet of your normal network your server is on. Your router would usually be 192.168.1.1 resolv-retry infinite nobind persist-key persist-tun ca "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\ca.crt" cert "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\client1.crt" # Change the next two lines to match the files in the keys directory. This should be be different for each client. key "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\client1.key" # This file should be kept secret ns-cert-type server cipher BF-CBC # Blowfish (default) encrytion comp-lzo verb 1 To me it looks like I will need to amend the following: remote YOURHOST.dyndns.org 1194 #You will need to enter you dyndns account or static IP address here. The number following it is the port you set in the server's config route 192.168.1.0 255.255.255.0 vpn_gateway 3 #This it the IP address scheme and subnet of your normal network your server is on. Your router would usually be 192.168.1.1 So, should the first line be the static IP of the machine that I'm applying this to? The IP address of the server (192.168.1.10) or something else? I'm also stuck on the second part 'route 192.168.1.0 255.255.255.0 vpn_gateway 3' Should this be the router IP which is 192.168.1.1 and the subnet is 255.255.255.0 and that is all I need to alter? The final part that I'm stuggling with is Configuring the router. Basically I have a Netgear DGN2000 and as it mentions that the router should be configured to port forward port 1194 to the server’s IP address of 192.168.1.150 all I have been able to do is in 'Firewall Rules' and on 'Inbound Services', set the Service to 'Any(ALL) and Send to LAN Server point to 1923.168.1.150. I'm not sure if this is correct? It is the following stage of the help guide that I'm struggling with and really need some help with: You need to make sure the port you configured OpenVPN to listen on is forwarded on the router to the IP address of your server. On the WRT54G, port forwarding is configured in the “Applications & Gaming” section. Enter 1194 for the port, UDP for the protocol, and 192.168.1.150 for the IP address. Make sure the entry is enabled and then save the setting. Next, you need to add an entry to the router’s Routing Table. This will enable the router to properly route requests from the clients to the TAP interface of the server. On the WRT54G you would go to the “Setup” page and then the “Advanced Routing” section. Enter the follwing info to make the entry: Enter Route Name: openVPN Destination LAN IP: 192.168.10.0 Subnet Mask: 255.255.255.252 Default Gateway: 192.168.1.150 Interface: LAN & Wireless Once the info has been typed in make sure you save the setting. Can anyone possibly guide me through setting this part up with my Netgear router. I see that once I have these 2 parts complete I'm there so I would really appreciate someone walking me through what is required in completing this. Much appreciated.

    Read the article

< Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >