Search Results

Search found 11077 results on 444 pages for 'ip'.

Page 163/444 | < Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >

• Google Public DNS is not used in trace route

  - by IT researcher

  In my PC i am using google public DNS as DNS server.In Internet protocol(TCP/IP) properties i have set Preferred DNS server as 8 8 4 4 and Alternate DNS server as 8 8 8 8. According to me this DNS server should be used to resolve any request to website to its IP by using this DNS servers.(see google DNS and How Domain Name Servers Work). But when i checked trace route to a website in my PC i got following Tracing route to www.google.com [74.125.236.80] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 192.168.1.201 2 360 ms 349 ms 292 ms 122.178.216.1 3 145 ms 107 ms 148 ms 122.166.32.121 4 32 ms 53 ms 120 ms 122.166.32.9 5 45 ms 42 ms 121 ms 122.175.255.29 6 63 ms 76 ms 51 ms 182.79.255.45 7 52 ms 134 ms 61 ms 72.14.194.22 8 86 ms 59 ms 72 ms 72.14.232.202 9 106 ms 107 ms 60 ms 66.249.94.39 10 101 ms 103 ms 117 ms 209.85.249.235 11 148 ms 224 ms 276 ms 74.125.236.80 Trace complete. When i checked all these IP in who.is i found that it is of my ISP. So my question is where does Google public DNS is used? Also how come my ISP's nameserver is used even if i set google public dns as my dns server in my PC?(OR does my any settings are wrong)

  Read the article

• Centos IPTables configuration for external firewall

  - by user137974

  Current setup Centos which is a Web, Mail (Postfix,Dovecot), FTP Server and Gateway with public ip and private ip (for LAN Gateway). We are planning to implement external firewall box and bring the server to LAN Please guide on configuring IPTables... Unable to receive mail and outgoing mail stays in postfix queue and is sent after delaying... The local ip of the server is 192.168.1.220 iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP incoming HTTP iptables -A INPUT -i eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 443 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 443 -m state --state ESTABLISHED -j ACCEPT outgoing HTTP iptables -A OUTPUT -o eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT FTP iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 21 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 21 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 1024:65535 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 1024:65535 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT SMTP iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 25 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 25 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 1024:65535 -d 0/0 --dport 25 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -p tcp -s 0/0 --sport 25 -d 192.168.1.220 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT POP3 iptables -A INPUT -p tcp -s 0/0 --sport 1024:65535 -d 192.168.1.220 --dport 110 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -s 192.168.1.220 --sport 110 -d 0/0 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT

  Read the article

• Managing Many External Hosts Using EC2 and Route 53

  - by futureal

  Looking for a "best practice" answer to managing externally-addressable hosts using the combination of Amazon EC2 and Amazon Route 53, without using Elastic IPs for each host. In my scenario I will have 30+ hosts that need to be accessible from outside EC2, so directly using internal DNS will not work. In the past, I have addressed hosts by assigning an elastic IP to that host (let's say, 55.55.55.55) and then creating an associated A record. For example, let's say I want to create "ec2-corp01.mydomain.com" I might do: ec2-corp01.mydomain.com. A 55.55.55.55 300 Then on that EC2 instance, I would assign the Elastic IP of 55.55.55.55, and everything works fine. Of course, to make this work, I need to have one Elastic IP per instance, which is something I'd like to avoid if possible; I'd like the infrastructure to be more dynamic. So my thought is to try something like: Create a script that queries the internal EC2 tools to determine an instance's private hostname On instance boot, call that script to determine its hostname, and then using the command-line Route 53 interface to find and update that hostname to its current internal hostname Since the host will have a relatively low TTL (let's say 300 as above, or 5 minutes) it should take effect pretty quickly Is this a good idea? Is there a better or more widely accepted way to handle it? If it IS a good idea, what type of record should I be creating? A CNAME that points to the internal host, like ec2-55-55-55-55.compute-1.amazonaws.com? Is an A record better or worse? Thanks!

  Read the article

• VPN Error 619: Behind Cisco Router WRT310N

  - by ty91011

  I've researched a lot on all the forums and this error is too generic for any of the proposed solutions to work. I'll try to give as much detail and tried solutions. I'm running a CentOS PPTP server behind a Cisco WRT310N Router. Multiple clients from outside with different OS have failed with the same error 619, along with turning off windows firewall and disabling antivirus. I believe this is a router and IP routing issue, and not a client issue. When I connect from a client on the same router as the VPN server, it works when I use the 192. network address- but doesn't work with the public IP address. I've tried telnet to port 1723 from an outside server and I get in. I've opened up the VPN port (1723) on the router, VPN udp port (500), and the GRE port (47) to route to the VPN server's ip. Also, the server's router is behind a DSL modem. I had a glimmer of hope when this site: http://www.chicagotech.net/casestudy/vpnerror619.htm suggested that the PPoE authentication should reside on the router and not the modem. But I still came up empty. So does anybody know what the problem is?

  Read the article

• iptables (NAT/PAT) setup for SSH & Samba

  - by IanVaughan

  I need to access a Linux box via SSH & Samba that is hidden/connected behind another one. Setup :- A switch B C |----| |---| |----| |----| |eth0|----| |----|eth0| | | |----| |---| |eth1|----|eth1| |----| |----| Eg, SSH/Samba from A to C How does one go about this? I was thinking that it cannot be done via IP alone? Or can it? Could B say "hi on eth0, if your looking for 192.168.0.2, its here on eth1"? Is this NAT? This is a large private network, so what about if another PC has that IP?! More likely it would be PAT? A would say "hi 192.168.109.15:1234" B would say "hi on eth0, traffic for port 1234 goes on here eth1" How could that be done? And would the SSH/Samba demons see the correct packet header info and work?? IP info :- A - eth0 - 192.168.109.2 B - eth0 - 192.168.109.15 - eth1 - 192.168.0.1 C - eth1 - 192.168.0.2 A, B & C are RHEL (RedHat) But Windows computers can be connected to the switch. I configured the 192.168.0.* IPs, they are changeable. Any help?

  Read the article

• InterVLAN routing on a HP V1910 series switch

  - by tintix

  Recently bought a HP V1910-16G switch (former 3com 29??) with IPv4 routing capabilities. After unpacking I did a firmware upgrade to the latest 5.20 Release 1513P06. I did set up additional VLANs (#2 and #3) and VLAN interfaces for those. The problem is that connected PCs on different VLAN's can't ping each other. Looks like VLAN routing doesn't even work. So here's my setup: VLAN ID VLAN interface 1 10.0.0.21/24 2 10.0.5.1/24 3 10.0.6.1/24 Have one PC connected to VLAN 2 (IP address 10.0.5.2, default gateway 10.0.5.1) and a second PC connected to VLAN 3 (IP address 10.0.6.2, default gateway 10.0.6.1) Routing table: Destination IP Mask Next Hop 0.0.0.0 0.0.0.0 10.0.0.1 10.0.0.0 255.255.255.0 10.0.0.21 10.0.0.21 255.255.255.255 127.0.0.1 10.0.5.0 255.255.255.0 10.0.5.1 10.0.5.1 255.255.255.255 127.0.0.1 10.0.6.0 255.255.255.0 10.0.6.1 10.0.6.1 255.255.255.255 127.0.0.1 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 255.255.255.255 127.0.0.1 The first PC can't ping the second PC one and vice versa. They only can ping their own gateways and that's all. What I'm doing wrong?

  Read the article

• dnsmasq(as DHCP server) isn't working in KVM+libvirt envirmont

  - by user2681054

  I'm using dnsmasq as DHCP server in VM environment. But It didn't working. I disabled basic DHCP feature in libvirt. <network> <name>default</name> <uuid>84da0678-e56d-8fc2-6f8b-e8eba784849a</uuid> <forward mode='nat'/> <bridge name='virbr0' stp='on' delay='0' /> <mac address='52:54:00:7B:64:0B'/> <ip address='192.168.122.1' netmask='255.255.255.0'> </ip> </network> As you can see, I removed this tag! <dhcp> <range start='192.168.122.2' end='192.168.122.254' /> </dhcp> And I installed dnsmasq in Host machine. During installation dnsmasq, there was an error message about 127.0.0.1.(dnsmasq: failed to create listening socket for 127.0.0.1) So I commented out listen-address option, and added dhcp-range/dhcp-option options, like this. listen-address=127.0.0.1 dhcp-range=192.168.122.100,192.168.122.200,24h dhcp-option=option:router,192.168.122.1 That's all I've done with dnsmasq. But guest VM couldn't get IP address from host which is dnsmasq server running. After that , I installed isc-dhcp-server instead of dnsmasq.... and it works! But I still want to use dnsmasq instead of isc-dhcp-server. Are there any helping hands? I disabled host machine's firewall. I've heard that libvirt basically use dnsmasq. Is this the reason why I couldn't use dnsmasq in libvirt environment?

  Read the article

• Failed to bring up eth1 in a dual ips solution in ubuntu

  - by lxyu

  I'm using ubuntu 12.04. I tried to assign two ips to two ethernet cards in my server. The content of /etc/network/interfaces is like this: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 114.80.156.a netmask 255.255.255.224 gateway 114.80.156.b auto eth1 iface eth1 inet static address 114.80.156.c netmask 255.255.255.240 gateway 114.80.156.d a b c d have different values, which means the two ips are in different vlans. But I can only bring up eth0 with this command: $ /etc/init.d/networking restart RTNETLINK answers: File exists Failed to bring up eth1. ...done. I have checked the question here which shows the same problem like the one I encountered: Can only bring up one of two interfaces But it seems it's not really solved. And in my situation, I need the 2 ips to use 2 different gateways. So how to fix this problem? Edit1, changed the example config ip from 192.168.0.0/16 subnet to another 'real' subnet. Edit2, the purpose of doing this is fairly simple. Because the ip range I previous in don't have more room for new servers, and I have to move to another ip range. So I want to make the public servers bind to 2 ips for the transition period. I only have really limited knowledge about routing and subnet. @BillThor @rackandboneman, would you please give me some keywords or links on how to setup route for 2 ips? and @Mike Pennington, how do you know I speak chinese?

  Read the article

• VLAN with trunk to avoid broadcast storm in a network with redundant paths

  - by liv2hak

  I have 6 Juniper switches (EX - 2200) connected to each other as shown in the network topology. I have two PC's that I am using PC1 - (used for configuring the 6 switches via minicom) PC2 - to monitor the traffic between the switches via the Ports that are marked with arrows in the diagram. STEP 1: I create a new vlan On Switch 3 (SW3) that includes Port 12 and Port 22. I also assign l3-interface to the vlan (vlan_2) with ip address - 192.168.1.7. Now I plug-in Port 0 of Switch 3 on PC2. Now I try pinging 192.168.1.7 from PC2 (192.168.1.10) I want to know what will happen? My postulation is that I will not be able to ping SW3 from PC2.This is because SW3 (Port 12 and Port 22) is a part of a vlan_2 and vlan_2 logically breaks up broadcast domains and so 192.168.1.7 will not be reachable from 192.168.1.10. Now I have an l3-interface on SW1 with IP 192.168.1.1 using default vlan( vlan-id 0). Similarly I have enabled IP on SW2 - 192.168.1.2 SW3 - 192.168.1.3 SW4 - 192.168.1.4 SW5 - 192.168.1.5 SW6 - 192.168.1.6 all using default vlan. I create VLAN2 with the following configuration SW3 - Port 12,Port 22. SW6 - Port 14 I create VLAN3 with the following configuration SW3 - Port 0 SW6 - Port 0 I also configure a VLAN trunk between SW3 and SW6 using the following commands. edit interfaces ge-0/0/12 set unit 0 family ethernet-switching port-mode trunk edit interfaces ge-0/0/12 set unit 0 family ethernet-switching vlan members all There is a redundant path in the network as the loop between SW3 and SW6 is closed.There is no broadcast storm in the network? What is the reason for this? I have not enabled STP or RSTP.still there is no broadcast storm.what is the reason for this. (Please ignore the CISCO symbol on the switches in the diagram.All swithes are Junper EX 22-00.)

  Read the article

• DNS setup problems with Windows Azure VPS

  - by jbigelow

  What is the proper to setup the A record (or CNAME) for a Windows Azure VPS? I can't connect to my website after setting up IIS and believe I don't have the correct DNS setup. I created a small VPS instance with the default Windows Server 2012 configuration. I RDP'd in and added the Webserver role. In my DNSMadeEasy control panel I added an A record with my Public Virtual IP Address. In IIS I went to the default website and added bindings for the hostname of my website, so I should be able to type mywebsite.com and see the IIS 8 splash screen, but instead my browser cannot connect. I attempted to navigate to the site by typing in my Virtual IP address into the browser and still cannot connect. I RDP'd back into the machine and turned off Windows Firewall. No change, still cannot navigate to my website. From within IIS I double checked my binding. If I click "browse *:80" I can bring up my website in IE with the http:// localhost address. If I click "browse mywebsite on *.80" IE says "This page cannot be displayed.", from within the RDP session I can view the site if I navigate to http:// 127.0.0.1 but not if I navigate to my Virtual IP, nor can I view the page if I try navigating to http:// mywebservername.cloudapp.net I'm thinking I must be fundamentally not understanding how do DNS setup with Azure VPS but my initial Google searches aren't turning up any helpful information. (spaces added after the http:// so serverfault doesn't try and render them as valid urls.)

  Read the article

• Is my dns server being attacked? And what should I do about it?

  - by Mnebuerquo

  I've been having some intermittent dns problems with a web server, where certain isp's dns servers don't have my hostnames in cache and fail to look them up. At the same time, queries to opendns for those hostnames resolve correctly. It's intermittent, and it always works fine for me, so it's hard to identify the problem when someone reports connectivity problems to my site. In trying to figure this out, I've been looking at my logs to see if there are any errors I should know about. I found thousands of the following messages in my logs, from different ip's, but all requesting similar dns records: May 12 11:42:13 localhost named[26399]: client 94.76.107.2#36141: query (cache) 'burningpianos.com/MX/IN' denied May 12 11:42:13 localhost named[26399]: client 94.76.107.2#29075: query (cache) 'burningpianos.com/MX/IN' denied May 12 11:42:13 localhost named[26399]: client 94.76.107.2#47924: query (cache) 'burningpianos.com/MX/IN' denied May 12 11:42:13 localhost named[26399]: client 94.76.107.2#4727: query (cache) 'burningpianos.com/MX/IN' denied May 12 11:42:14 localhost named[26399]: client 94.76.107.2#16153: query (cache) 'burningpianos.com/MX/IN' denied May 12 11:42:14 localhost named[26399]: client 94.76.107.2#40267: query (cache) 'burningpianos.com/MX/IN' denied May 12 11:43:35 localhost named[26399]: client 82.209.240.241#63507: query (cache) 'burningpianos.com/MX/IN' denied May 12 11:43:35 localhost named[26399]: client 82.209.240.241#63721: query (cache) 'burningpianos.org/MX/IN' denied May 12 11:43:36 localhost named[26399]: client 82.209.240.241#3537: query (cache) 'burningpianos.com/MX/IN' denied I've read of Dan Kaminski's dns cache poisoning vulnerability, and I'm wondering if these log records are an attempt by some evildoer to attack my dns server. There are thousands of records in my logs, all requesting "burningpianos", some for com and some for org, most looking for an mx record. There are requests from multiple ip's, but each ip will request hundreds of times per day. So this smells to me like an attack. What is the defense against this?

  Read the article

• When I ping Internet addresses like yahoo or Google, I get 2 reply packets and 2 lost packets.

  - by navi

  I have Airtel broadband and a Tata broadband connection. i have around 50 PCs connecting through an airtel broadband connection. Both are dsl connections with my phone line going into dsl modems and an Ethernet cable going from dsl modem directly into a switch. Currently, only airtel connection is connected with static IP on my private lan and using the airtel ISP DNS servers as DNS IP address and the default gateway is 192.168.1.1 (IP add. of the dsl modem). All PCs are connected in a work group. When in full use, my users complain of certain web pages are not opening. When I ping Internet addresses like Yahoo or Google I get 2 reply packets and 2 lost packets. I suspect that a single broadband connection is not able to sustain 50 simultaneous downloads/browsing. Is there any device which connect to both DSL and make one line so that its give me high speed simultaneous browsing. Help needed urgently. Thank you all to those who reply.

  Read the article

• Can't connect to a Hyper-V VM from anywhere but the host OS

  - by Elbelcho

  I have an unusual situation on hand where I'm able to connect to a Hyper-V guest VM from the HOST, but not from anywhere but the host. The VM is running WIn2k8R2 and has IIS installed and Remote Desktop enabled. If I browse to the IP from the host OS, the IIS7 page displays. I can also RDP into the guest OS from the host as well as ping. From OFF the host, RDP, web and ping all fail. If I completely shut off the guest VM's firewall, ping will then start to respond, but all RDP and port 80 still don't. The physical host machine has 2 nics installed, but only one is plugged in. The one plugged in has a static IP. I have one Hyper-V virtual network and it's set to external. The guest VM has one NIC with a different static IP than the host, but both are on the same subnet. The host machine is joined to the domain, the guest VM is not. Any sugestions? Thanks so much for any help you may be able to provide!

  Read the article

• Virtual bridged networking with VLAN, could not ping

  - by v.yegy

  I require a virtual network with VLAN be build between two virtual hosts - which can be (lxc/ vbox -ubuntu or win xp). I tried with lxc and vbox with Ubuntu and was finding difficult to make it work without vlan, but was successful with vbox with xp. vbox-xp1 --- br1 ---------------- br2 ---- vbox-xp2 The config is: brctl addbr br1; brctl addbr br2 ifconfig br1 up; ifconfig br2 up stp br1 off; stp br2 off ip link add name br1-br2-l0 type veth peer name br1-br2-l1 sudo brctl addif br1 br1-br2-l0 sudo brctl addif br2 br1-br2-l1 vbox - xp 1 and 2 with network ; bridged and br1 and br2 respectively. The adapter is intel PRO/1000 MT Server and driver installed in guests. Configured IPs and two hosts pinged! VLAN config: ip link add link br1 name br1-2.5 type vlan id 5 brctl addif br2 br1-2.5 create vlan 5 in xp 1 and 2 and assign ip address Ping on with this config does not work. Wireshark trace on interface br1-br2-l1 / br1-2.5 shows that one ping results in ~240 ping packets and each growing by 4 bytes - first one being correct and 60, ping does not reach other host as I see mac is not learnt[arp -a]. -- if br1-2.5 is not configured, I see untagged packets in br1-br2-l1/0, but still not reaching other host as mac is not learnt. if br1-br2-l0/1 is made down, even if br1-2.5 is up, I count not see any packets. I tried with ebtables, but still could not make a correct config to work. -- If any one here are aware of any configuration, please let me know. I need to make a network of switches. Seems I have a very long way. Sorry for a very long question. Thanks and regards, vy

  Read the article

• Can I run a mix of static addressing and NAT?

  - by aroth

  Let's say that an ISP offers a plan with 5 static IP addresses, but I have more than 5 devices, many of which (such as a networked printer, for instance) I do not want or need to have a static IP address. So the topography I'm planning goes something like: ISP -> Router -> Switch -> Computer (static address) -> Computer (static address) -> Printer (DHCP/NAT) -> Tv (DHCP/NAT) -> (...) -> Wireless Devices (DHCP/NAT) Generally speaking, is it possible to run a network like that? If not, then what sort of setup do I need so that I can assign static addresses just to the things that need them, and use DHCP/NAT for everything else? Also, what internal networking devices will consume a static IP address? I'm pretty sure the router will, correct? Does the switch also?

  Read the article

• Windows 2003 Active Directory Integrated DNS zone not registering non-domain computers

  - by Jeff Willener

  I'm not a networking guy by all means, I'm just a developer who dabbles enough to get into trouble and I'm there. So bear with me... :) At my office I have a Windows 2003 Domain Controller which also services DNS. On the domain I have a handful of computers and other misc. equipment/toys. For the DNS I only created a Forward Lookup Zone for my domain (mydomain.com). I run a lot of VM's so generally I have everything on the domain, however some of those VM's are not and only in a 'Workgroup'. I also have another laptop which belongs to another domain (otherdomain.com) which is here 100% but I use it for other purposes and has to belong to the otherdomain.com. With all that said, I have two questions: I have found any computer not on mydomain.com does not register it's IP address even though 'Register this connections address in DNS' is set to in the 'Advanced TCP/IP Settings' for the nic. Where have I messed this up? On the laptop which is registered on otherdomain.com, when I do a nslookup for a computer on mydomain.com (e.g. nslookup devbox1) it appends otherdomain.com as the suffix (e.g. queries devbox1.otherdomain.com). Same thing occurs if I use the fully qualified name. In the 'Advanced TCP/IP Settings' for that nic, I can 'Append these DNS suffixes' of mydomain.com but I fear that will hose my DNS lookups when I VPN to otherdomain.com. So what is the correct approach to resolve this issue? Do I add both mydomain.com and otherdomain.com in that order?

  Read the article

• ProCurve network expansion

  - by Blue Warrior NFB

  I've hit a bit of a wall with our network scale-out. As it stands right now: We have five ProCurve 2910al switches connected as above, but with 10GbE connections (two CX4, two fiber). This fully populates the central switch above, there will be no more 10GbE Ethernet connections from that device. This group of switches is not stacked (no stack directive). Sometime in the next two or three months I'll need to add a sixth, and I'm not sure how deep of a hole I'm in. Ideally I'd replace the core switch with something more capable and has more 10GbE ports. However, that's a major outage and that requires special scheduling. The two edge switches connected via fiber have dual-port 10GbE cards in them, so I could physically put another switch on the far end of one of those. I don't know how much of a good or bad idea that would be though. Is that too many segments between end-points? Some config-excerpts: Running configuration: ; J9147A Configuration Editor; Created on release #W.14.49 hostname "REDACTED-SW01" time timezone 120 module 1 type J9147A module 2 type J9008A module 3 type J9149A no stack trunk B1 Trk3 Trunk trunk B2 Trk4 Trunk trunk A1 Trk11 Trunk trunk A2 Trk12 Trunk vlan 15 name "VM-MGMT" untagged Trk2,Trk5,Trk7 ip helper-address 10.1.10.4 ip address 10.1.11.1 255.255.255.0 tagged 37-40,Trk3-Trk4,Trk11-Trk12 jumbo ip proxy-arp exit

  Read the article

• Problems sending email using .Net's SmtpClient

  - by Jason Haley

  I've been looking through questions on Stackoverflow and Serverfault but haven't found the same problem mentioned - though that may be because I just don't know enough about how email works to understand that some of the questions are really the same as mine ... here's my situation: I have a web application that uses .Net's SmtpClient to send email. The configuration of the SmtpClient uses a smtp server, username and password. The SmtpClient code executes on a server that has an ip address not in the domain the smtp server is in. In most cases the emails go without a problem - but not AOL (and maybe others - but that is one we know for sure right now). When I look at the headers in the message that was kicked back from AOL it has one less line than the successful messages hotmail gets: AOL Bad Message: Received: from WEBSVRNAME ([##.###.###.###]) by domainofsmtp.com with MailEnable ESMTP; Mon, 18 Jun 2012 09:48:24 -0500 MIME-Version: 1.0 From: "[email protected]" <[email protected]> ... Good Hotmail Message: Received: from mail.domainofsmtp.com ([###.###.###.###]) by subdomainsof.hotmail.com with Microsoft SMTPSVC(6.0.3790.4900); Thu, 21 Jun 2012 09:29:13 -0700 Received: from WEBSVRNAME ([##.###.###.###]) by domainofsmtp.com with MailEnable ESMTP; Thu, 21 Jun 2012 11:29:03 -0500 MIME-Version: 1.0 From: "[email protected]" <[email protected]> ... Notice the hotmail message headers has an additional line. I'm confused as to why the Web server's name and ip address are even in the headers since I thought I was using the SmtpClient to go through the smtp server (hence the need for the username and password of a valid email box). I've read about SPFs, DKIM and SenderID's but at this point I'm not sure if I would need to do something with the web server (and its ip/domain) or the domain the smtp is coming from. Has anyone had to do anything similiar before? Am I using the smtp server as a relay? Any help on how to describe what I'm doing would also help.

  Read the article

• Cannot establish a network connect to VMWare Fusion VM

  - by twolfe18

  I am running Snow Leopard 10.6.2 (not the server edition) with VMWare Fusion 3.0.0 and I trying to get my Ubuntu 9.10 x86_64 VM working. I am using a bridged connection, and I have an internet connection FROM the Ubuntu VM (I can download updates, ping websites, etc), but I cannot connect TO the Ubuntu box from any other device on my network. I am trying to get Mongrel up on the Ubuntu VM for some Rails stuff, but it's not working. I know Mongrel/Rails is not the problem because if I start the server on the Ubuntu VM, background the process, and then wget the index page, it works. I just cannot connect to the site from another IP. I have tried using a static IP and a DHCP IP configuration on the Ubuntu VM, neither work (for incoming connections, both work for outwards). I have port scanned the Ubuntu VM, and it appears that all ports are closed. However, the Ubuntu VM does respond to pings. I noticed a similar question here: http://serverfault.com/questions/99757/setting-up-a-bridged-network-with-vmware-fusion, but no answer. Any ideas?

  Read the article

• How can I bridge a VM to a remote network?

  - by asciiphil

  I have a system running QEMU/KVM (via libvirt). One of its VMs needs to have a presence on a subnet that is not local to the VM host. I have a Linux system on the remote subnet. Is there a way to set up some sort of tunneled bridge to cause the VM to appear present on the remote system? This will be a temporary situation (hopefully just until the VM owner can configure their system) and network performance and long-term maintainability aren't really issues. To give some more concrete information: My VM host has IP address 192.168.54.155/24. The VM has IP address 192.168.65.71/24. I have a remote system at 192.168.65.254/24. Both the VM host and remote system are running Scientific Linux 6.5. I do not control the network or routing in between the VM host and remote system. I do not have access to the guest OS on the VM. I would like traffic to the VM's IP address to end up at the VM even though its host isn't directly connected to the appropriate network. I've tried using iproute2's tunnelling, but Linux won't let me add a tunnel to a bridge. I've considered using some sort of iptables mangling to route traffic over the tunnel and make the VM think it's on the right network, but I'm not sure whether there are better approaches. What's the best way to accomplish this hack?

  Read the article

• Read Only Domain Controllers and DNS zone updates

  - by Mike M

  I have a Windows 2003 domain and just added a new DC that runs 2008 R2. I updated the schema accordingly for both forest and domain levels. I also made sure to run /rodcprep at the time I did this. I have a branch office with a 2008 R2 file/print server that is a read-only domain controller (DC). The one problem I have been having is with AD-integrated DNS records updates. In the data center, we had to make an IP address change on a particular server. All our other sites' DCs (2003) updated the record fine. The 2008 R2 DC in the data center also updates its record fine. However, the RODC in the branch office does not. So if I nslookup the target server on a 2003 DC, the IP address is correct. Same with the 2008 R2 DC in the data center. But an nslookup on the branch office RODC still pulls in the old IP address. Moreover, any new records we've created (e.g., just added a new terminal server) do not get updated on the branch RODC either. Is there something simple I'm missing? How do I get the RODC to sync its AD-integrated DNS records with the rest of my world? Thank you in advance for your responses. Mike

  Read the article

• simple network between xp & 7 with cross cable problem...

  - by LostLord

  hi my dear friends : i have a simple network between xp & 7 windowses with cross cable (2 pc home)... ===================================================================== the one with 7 is mother and have 2 lan device (onboard + pci) A. onboard is like this when u go to tcp/ip v4 properties:(4 adsl internet) obtain an ip... preferred dns server : 81.91.129.67 alternate dns server : 4.2.2.4 shared...no permission 4 change so every thing is ok for internet on windows 7. B. the other lan pci card that is connected to pc with xp is like this : 192.168.2.11 255.255.255.0 0.0.0.0 empty empry computer name : cougar workgroup : nethome homeNetwork is disabled (i think that is 4 2 pc's with 7 os not xp) every thing is off in network options except file & printer sharing in public area ===================================================================== pc with xp os is like this : 192.168.2.12 255.255.255.0 192.168.2.11 (mean gateway) 4.2.2.4 8.8.8.8 computer name : tiger workgroup : nethome ===================================================================== at last my little net is ok... mean both have internet , both can see each other by their ip (\\192.168.2.11 or \\192.168.2.12) my problem is when in pc with xp type \\cougar it shows an error about network path! but in pc with 7 \\tiger works perfec. what is the problem in system with xp ? in few days ago this network was ok (search by computer name) when both os were xp , so there is no problem with my cable or devices. another problem is i can not find tiger in my network list in 7 pc \ why? is something wrong with my network? thanks 4 future advance best regards

  Read the article

• How to add commands of windows to local shell of XShell 4

  - by dylanninin

  XShell is a very powerful tools to ssh remote computers such as Unix/Linux. And it has built some internal commands for you to run within your Windows. Xshell:\> help Internal Commands: new: Creates a new session. open: Opens a session or the session dialog box. edit: Opens the Session Property dialog box for a session. list: Lists information of all available sessions. 'ls' and 'dir' do the same. cd: Changes the current working directory. clear: Clears the screen/address/command history. help: Displays this help. '?' does the same. quit: Quits Local Shell. 'exit' does the same. ssh: Connects to a host using the SSH protocol. telnet: Connects to a host using the TELNET protocol. rlogin: Connects to a host using the RLOGIN protocol. sftp: Connects to a host to transfer files securely. ftp: Connects to a host to transfer files. External Commands: ipconfig: Configures TCP/IP network interfaces. ping: Sends ICMP ECHO_REQUEST packets to network hosts. tracert: Prints the route packets take to network host. netstat: Displays current protocol statistics and current TCP/IP network connections. nslookup: Resolves a hostname to IP address. For more information, type 'help command' for each command. ex) help telnet But these commands are limited, so how to add commands of windows to local shell of XShell 4

  Read the article

• How to connect through a proxy using Remote Desktop?

  - by scottmarlowe

  So I've got a home server running Windows Server 2003. I use a dual network card setup and Routing and Remote Access to link the internal, private network to the external connection. The external connection hooks directly to my cable modem (so no routers or other devices sitting between). The problem I'm having is that I can't connect remotely from a location outside the house (so connecting to the server's external connection) to the server using either Remote Desktop or VNC. I have enabled both ports in Routing and Remote Access's firewall to allow access, and I have enabled Remote Desktop in Windows Server 2003. The odd thing is that I can access my home server's SVN repository and I can even ping the server's IP. I am using the IP to attempt to connect, though I use a dyndns.com provided name to connect to my SVN repository, so it shouldn't make a difference (I know the IP is getting resolved correctly). Any ideas on where to start diagnosing this one? I haven't seen anything in my server's event log. If any other info is needed, let me know. Thanks. UPDATE: One last piece of information: We use a proxy server at work, which I'm nearly 100% sure is the culprit. I have a workaround--if I connect to our VPN (even though I'm already inside the building) I am able to connect to my home server. This is with VNC. However, is there a way to connect through a proxy using Remote Desktop? ONE MORE UPDATE: Indeed, it was the http proxy I'm sitting behind at work that was causing the issue. An acceptable workaround is to use my VPN connection to bypass the proxy, and I'm in!

  Read the article

• Are Colocation Cross Connects Worth While

  - by SvrGuy

  We currently operate three clusters of collocated machines in different data centers. Recently, I became aware that our newest data center will offer to cross connect us to a bandwidth provider free of charge. In the past, I never really investigated a cross connect for bandwidth because I figured that the rates would be similar to what we are paying the colo now and that it would reduce our resiliency (because we would only be using one or two carriers for IP, where as the colo uses, say 8 different providers). Then I saw an ad for hurricane electric internet services (http://he.net/cgi-bin/ip_transit_quote) that gave a price for IP transit at $1/Mbs, which is much better than the $30/Mb we pay for the blended bandwidth. What are people out there typically paying for bandwith via cross connect and how hard is to setup? Is my understanding that what you do is open agreemetns with two or three ISPs, cross connect to them and then configure your top of rack router on their network. Can you really get IP transit down to a couple of dollars per megabit per month just by doing the routing yourself? Or, is my understanding of cross connection fundamentally wrong?

  Read the article

< Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >