Search Results

Search found 15651 results on 627 pages for 'setup'.

Page 163/627 | < Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >

  • SSH connection problem - allowed from LAN but not WAN

    - by Kerem Ulutas
    I tried to setup my Arch Linux installation to be an SSH host, but here is the thing: I can ssh localhost, it fails to login via public key and asks for username and password, but still able to login. When I try ssh my_wan_ip it gives ssh_exchange_identification: Connection closed by remote host error. I've read all topics about this error and none helped me. By the way, just confirmed, it gives ssh: connect to host my_dyndns_hostname port 22: Connection refused from another machine (outside of my network, it has different wan ip). I have sshd: ALL in "hosts.allow", ALL:ALL in "hosts.deny". I am able to connect to my own pc via ssh, ping my own pc, but my ssh setup seems to be the problem, it gives that annoying error when I try to ssh from wan. /etc/ssh/ssh_config /etc/ssh/sshd_config And finally, here is the debug output for both sshd and ssh: (i ran ssh command and i took output to sshd debug after that): sshd debug ssh debug I can edit my question according to your needs. Just ask for any more information needed. BTW I have no iptables running. I have one cable dsl modem connected to a asus wl-330gE wireless access point, they both have their firewall disabled. I configured NAT so port 22 is directed to the pc I'm having this trouble. Any help appreciated, thanks..

    Read the article

  • OpenSWAN KLIPS not working

    - by bonzi
    I am trying to setup IPSec between 2 VM launched by OpenNebula. I'm using OpenSWAN for that. This is the ipsec.conf file config setup oe=off interfaces=%defaultroute protostack=klips conn host-to-host left=10.141.0.135 # Local IP address connaddrfamily=ipv4 leftrsasigkey=key right=10.141.0.132 # Remote IP address rightrsasigkey=key ike=aes128 # IKE algorithms (AES cipher) esp=aes128 # ESP algorithns (AES cipher) auto=add pfs=yes forceencaps=yes type=tunnel I'm able to establish the connection with netkey but klips doesnt work. ipsec barf shows #71: ERROR: asynchronous network error report on eth0 (sport=500) for message to 10.141.0.132 port 500, complainant 10.141.0.135: No route to host [errno 113, origin ICMP type 3 code 1 (not authenticated)] Tcpdump shows 22:50:20.592685 IP 10.141.0.132.isakmp > 10.141.0.135.isakmp: isakmp: phase 1 I ident 22:50:25.602182 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:26.602082 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 22:50:27.601985 ARP, Request who-has 10.141.0.135 tell 10.141.0.132, length 46 ipsec eroute shows 0 10.141.0.135/32 -> 10.141.0.132/32 => %trap What could be the problem?

    Read the article

  • Network Load Balancing and AnyCast Routing

    - by user126917
    Hi All can anyone advise on problems with the following? I am planning on installing the following setup on my estate: I have 2 sites that both have a large amount of users. Goals are to keep things simple for the users and to have automatic failover above the database level. Our Database will exist at the primary site and be async mirrored to the secondary site with manual failover procedures.The database generate sequential ID's so distributing it is not an option. I plan to site IIS boxes at both sites with all of the business logic on them and heavy operations. The connections to SQL will be lightweight and DB reads will be cached on IIS. On this layer I plan to use Windows network load balancing and have the same IP or IPs across all IIS boxes at both sites. This way there will be automatic failover and no single point of failure. Also users can have one web address regardless of which site they are in automatically be network load balanced to their local IIS. This is great but obviously our two sites are on different subnets and as this will be one IP address with most of our traffic we can't go broadcasting everything across the link between the sites. To solve this problem we plan to use AnyCast routing over our network layer to route the traffic to the most local box that is listening which will be defined by the network load balancing. Has anyone used this setup before? Can anyone think of any issues with this? Also some specifics I can't find anywhere at the moment. If my Windows box is assigned an IP and listening on that IP but network load balancing is not accepting specific traffic then will AnyCast route away from that? Also can I AnyCast on a socket level?

    Read the article

  • SharePoint web services not protected?

    - by Philipp Schmid
    Using WSS 3.0, we have noticed that while users can be restricted to access only certain sub-sites of a site collection through permission settings, the same doesn't seem to be true for web services, such as /_vti_bin/Lists.asmx! Here's our experimental setup: http://formal/test : 'test' site collection - site1 : first site in test site collection, user1 is member - site2 : second site in test site collection, user2 is member With this setup, using a web browser user2 can: - access http://formal/test/site2/Default.aspx - cannot access http://formal/test/site1/Default.aspx That's what is expected. To our surprise however, using the code below, user2 can retrieve the names of the lists in site1, something he should not have access to! Is that by (unfortunate) design, or is there a configuration setting we've missed that would prevent user2 from retrieving the names of lists in site1? Is this going to be different in SharePoint 2010? Here's the web service code used in the experiment: class Program { static readonly string _url ="http://formal/sites/research/site2/_vti_bin/Lists.asmx"; static readonly string _user = "user2"; static readonly string _password = "password"; static readonly string _domain = "DOMAIN"; static void Main(string[] args) { try { ListsSoapClient service = GetServiceClient(_url, _user, _password, _domain); var result = service.GetListCollection(); Console.WriteLine(result.Value); } catch (Exception ex) { Console.WriteLine(ex.ToString()); } } private static ListsSoapClient GetServiceClient(string url, string userName, string password, string domain) { BasicHttpBinding binding = new BasicHttpBinding(BasicHttpSecurityMode.TransportCredentialOnly); binding.Security.Transport.ClientCredentialType = HttpClientCredentialType.Ntlm; ListsSoapClient service = new ListsSoapClient(binding, new System.ServiceModel.EndpointAddress(url)); service.ClientCredentials.UserName.Password = password; service.ClientCredentials.UserName.UserName = (!string.IsNullOrEmpty(domain)) ? domain + "\\" + userName : userName; return service; } }

    Read the article

  • Serve a specific set of error pages for different subdirectories

    - by navitronic
    I am currently trying to setup 2 different sets of Error documents for separate folders within a website. I have 2 folders within the root of a site: demo/ live/ Any requests that return 404's or 403's within the demo folder needs to load one set of pages for the Apache errordocuments, eg. ErrorDocument 404 /statuses/demo-404.html ErrorDocument 403 /statuses/demo-403.html And the live needs to go to similarly name files. ErrorDocument 404 /statuses/live-404.html ErrorDocument 403 /statuses/live-403.html So far I have tried placing an .htaccess file in both directories with the ErrorDocument directives setup pointing to the specific files, the 404 works fine and references the correct page. However, the 403s do not work and revert to the server default when trying to access forbidden folders within the demo directory, the logs indicate the following: [Wed Jun 16 04:47:44 2010] [crit] [client 115.64.131.144] (13)Permission denied: /home/abstract/public_html/demo/xxx/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable Is this correct? Would apache revert to default because it is trying to look for the htaccess in a folder it doesn't have permission in? Why wouldn't it work it's way back through the folder tree? Can I make it do this?

    Read the article

  • Windows XP / Outlook 2003 error messages

    - by AboutDev
    Can anyone help with this issue? I am trying to help someone and could use some expertise. Error Message #1: Microsoft Office Small Business Edition 2003 With CD icon "The feature you are trying to use is on a CD-ROM or other removable disk that is not available. Insert the 'Microsoft Office Small Business Edition 2003' disk and click OK. Use source: Microsoft Office Small Business Edition 2003" 1st got this message after CD was inserted to recover partial file STDP11N. Recovered STDP11N, however, still receiving pop up window with error message each time outlook opens. Had accidentally cleaned up old programs and suddenly this was missing. Reinstalled Microsoft Office Small Business Edition 2003 using install CD. Outlook worked buit keep getting error message pop up each time I open Outlook. Hit ok. Error Message #2: The path 'Microsoft Office Small Business Edition 2003' cannot be found. Verify that you have access to this location and try again, or try to find the installation package 'STDP11N.MSI' in a folder from which you can install the product Microsoft Office Small Business Edition 2003." Hit ok. Back to error message #1 Hit close window Error message #3: Error 1706. Setup cannot find the required files. Check your connection to the network, or CD-ROM drive. For other potential solutions to this problem, see C:\Program Files\Microsoft Office\ OFFICE11\1033\SETUP.CHM Error message #4 I'd created a file under D: drive on an external drive. "The path specified for the file D:...etc.. .pst is not valid. Hit ok. Brings up window to look in My Documents.

    Read the article

  • BackupExec 2012 File System Archiving - Access is denied to Remote Agent

    - by AllisZero
    Gentlemen, I've been struggling with a Trial version of Symantec Backup Exec 2012 for about a week now. It was installed as an upgrade to our 12.5 license, and the setup completed with no issues. The reason I upgraded is solely for the File System Archiving option as I'm working to reduce the amount of live data in my servers. Backups work A-Ok and I have followed the instructions in the Admin Manual to make sure I had filled all requirements. The account BE is running under is a member of the Local administrators group as required and has been added to the test share that I'm using to evaluate the archiving function. Testing the credentials in the job setup window always works fine, and I am able to add both regular and Admin$ shares to my Archive selection. However, every time I run the Archive job, I get the following message: https://dl.dropbox.com/u/59540229/BEXec.png I've already tried to troubleshoot DNS resolution issues as suggested in the Symantec KB to no avail. The only thing I can think of, at this point, is that a trial license doesn't allow me to use the Archiving function, although that would seem silly on their part. Appreciate any assistance or information. Thanks.

    Read the article

  • Destination NAT Onto the Same Network from internal clients

    - by mivi
    I have a DSL router which acts as NAT (SNAT & DNAT). I have setup a server on internal network (10.0.0.2 at port 43201). DSL router was configured to "port forward" (or DNAT) all incoming connections to 10.0.0.2:43201. I created a virtual server for port forwarding on DSL router. I also added following iptables rules for port forwarding. iptables -t nat -A PREROUTING -p tcp -i ppp_0_1_32_1 --dport 43201 -j DNAT --to-destination 10.0.0.2:43201 iptables -I FORWARD 1 -p tcp -m state --state NEW,ESTABLISHED,RELATED -d 10.0.0.2 --dport 43201 -j ACCEPT # ppp_0_1_32_1 is routers external interface. # routers internal IP address is 10.0.0.1 and server is setup at 10.0.0.2:43201 Problem is that connections coming from external IP addresses are able to access internal server using External IP address, but internal clients (under NAT) are not able to access server using external IP address. Example: http://<external_address>:43201 is working from external clients But, internal clients are not able to access using http://<external_address>:43201 This seems to be similar to the problem described in http://www.netfilter.org/documentation/HOWTO/NAT-HOWTO-10.html (NAT HOW-TO Destination NAT Onto the Same Network). Firstly, I am not able to understand why is this a problem for internal clients? Secondly, what iptables rule will enable internal clients to access server using external IP address? Please suggest.

    Read the article

  • OpenVZ vs KVM for Linux VMs

    - by Eliasdx
    Hardware: Intel® Core™ i7-920, 12 GB DDR3 RAM, 2 x 1500 GB SATA-II HDD (no SoftRaid because Proxmox developers don't support softraid and they are sure you'll run into problems) Software: Proxmox VE with KVM and OpenVZ support and debian everywhere I want to run multiple Linux VMs on this server. One for a firewall (I want to try pfSense), one for MySQL, one VM for nginx (my stuff) and ~2 VMs with nginx for other people's web sites. I don't think that pfSense will run in an OpenVZ environment but it should run in KVM. The question is if I should setup the other VMs using KVM or OpenVZ. In OpenVZ they should have less overhead for the OS itself but I don't know about the performance. I heard that KVM is more stable but needs more RAM and CPU. I found this diagram showing a OpenVZ setup on the same hardware I'm using. This guy uses an own VM for each and every website which is running on his server. I can't think of any advantage why he's using so many VMs.

    Read the article

  • problems installing mysql and phpmyadmin to localhost

    - by Joel
    Hi guys, I know there have been many similar questions, but as far as I can tell, most of the other people have gotten further than I have... I'm trying to get a WAMP setup happening. I've got PHP and Apache running and talking to each other. PHP is in c:\PHP Apache is in it's default program files folder. mySQL is in it's default install location. I have localhost setup at D:\public_html\ I'm able to navigate to localhost and see html and php files. But I have a simple mySQL test file: <?php // hostname or ip of server (for local testing, localhost should work) $dbServer='localhost'; // username and password to log onto db server $dbUser='root'; $dbPass=''; // name of database $dbName='test'; $link = mysql_connect("$dbServer", "$dbUser", "$dbPass") or die("Could not connect"); print "Connected successfully<br>"; mysql_select_db("$dbName") or die("Could not select database"); print "Database selected successfully<br>"; // close connection mysql_close($link); ?> When I try and open this, I get "could not connect" Now, I haven't even created a database yet, because I can't log into mySQL with phpmyadmin-so I think I've done something wrong in my mySQL install because they aren't talking to each other. I guess my main question is how do I first create a database in mySQL to be sure I have even installed it correctly?

    Read the article

  • Unable to record using Jmeter

    - by krish
    Hi, I am trying to record a http web page using Jmeter 2.3.3 version.I has setup the JMeter proxy and tried, but did n't work. I have followed the below steps. Launch jmeter 2.3.3, added thred group to test plan Under Workbench-add-non-test elements- added HTTP proxy server. proxy server setting are port:9090, target:use recording controller, grouping:donot group samplers, Type:HTTp request and checked the boxes of all under http sampler settings Saved the settings Now in browser(IE 7.0 or firefox 3.0.16), under connection settings, setup the manual proxy settings as local host and port as 9090(no auto detect settings nothing, only manual proxy). Setting saved Now in the jmeter, started the http proxy server. Open a browser and hit the webpage needs to be tested. The page is not opened. In fact because of the changes made in browsers, no pages are opened. Whenever i try hitting a page, the pages are recorded in the Jmeter. but without the page open, how can i test. I looking for an immediate answer and my work is blocked. Immediate answer would be appreciated.

    Read the article

  • Using my own Postfix, filtering spam and getting all the mail into my ISP's inbox

    - by djechelon
    Hello, I currently own a domain bought via GoDaddy.com, which provides me a basic email setup for the most common needs. I configured it to forward all mail to [email protected] to [email protected]. I also own a virtual server with a running Postfix that I use for a specific website (all mail to somedomain.com gets forwarded via LMTP to a program written by me). Since I'm recently experiencing some harassing by spammers, since GoDaddy doesn't seem to filter spam, and since my Windows Phone's Pocket Outlook cannot filter spam, I would like to use SpamAssassin to filter inbound spam by changing my domain's MX records to my server My ideal setup is the following: All mail delivered to somedomain.com gets redirected via LMTP as usual via virtual transport without any spam check All mail to [email protected] gets redirected to [email protected] after a severe spam check I don't care about [email protected] since I use just one address for now I would like to train SpamAssassin with customized spam rules, possibly based on the presence of certain keywords (links to certain unsubscribe pages I found recurring) I currently configured Postfix with transport somedomain.com lmtp:[127.0.0.1]:8025 .somedomain.com error: Cannot accept mail for this domain relay somedomain.com OK (I guess I should add mydomain.com OK too) virtual @mydomain.com [email protected] (looks like a catch-all rule, it's OK as requirement 3) I installed SpamAssassin, I can do rcspamd start and set it to boot with the server, but I don't know if there is anything else to do for use in Postfix, and how to apply requirement 1 (only mail to mydomain.com gets filtered) I also tried to send an email via Telnet to make sure my settings are ready for MX change. I received the message into my account but I found that it gone through secureserver.net, like Postfix didn't rewrite the destination but simply relayed the message. Thank you in advance. I'm no expert in SpamAssassin, and I have little experience in Postfix (enough to avoid making my server an open relay)

    Read the article

  • Xmonad on windows laptop

    - by Kevin L.
    I'm a Linux developer in the market for a laptop. 90% of my time is spent in Emacs, the terminal, and Google Chrome, and I want to use them within the excellent Xmonad tiling windows manager. Given these constraints, I can only see two options: Run Linux on a laptop Run Windows on the laptop, and spend all of my time working within a Linux VM. Years of experience suggest that the first option will take many frustrating hours and probably be suboptimal w.r.t. battery life, wifi, and fn keys like screen brightness or audio adjustment. For the second option, what would be the ideal setup? I've had a lot of luck with Cooperative Linux on my Samsung NC-10 netbook (Windows XP), but I would have to setup the X11 server myself. What about using VirtualBox (which includes the guest VM's GUI)? Has anyone tried this? Hardware-wise, I'm looking for something in the "Macbook Air killer" category; Samsung Series 9 laptop, Lenovo IdeaPad U300s, &c. (i.e., matte screen, 5h+ battery life, 3ish pound weight). Price is not a consideration; any suggestions?

    Read the article

  • DNS Issue- Nameserver Issue

    - by Master-Man
    I setup new server on centos 5.3 and configure dns and hostnam using WHM. I also register my new nameservers with my domain registrar with ns1.example.com and ns2.example.com. But i am unable to ping hostname and NS. ping pc2.example.com or ping ns1.example.com I received the below email from server. IMPORTANT: Do not ignore this email. Your hostname (pc2.example.com) could not be resolved to an IP address. This means that /etc/hosts is not set up correctly, and/or there is no dns entry for pc2.example.com. Please be sure that the contents of /etc/hosts are configured correctly, and also that there is a correct 'A' entry for the domain in the zone file. Some or all of these problems can be caused by /etc/resolv.conf being setup incorrectly. Please check that file if you believe everything else is correct. You may be able to automatically correct this problem by using the 'Add an A entry for your hostname' option under 'Dns Functions' in your Web Host Manager. When I issue the command root@pc[~]# host pc2.example.com I receive the below error that Host pc2.example.com not found: 3(NXDOMAIN) I added A entries for hostname and Nameservers but nothing replies. Its almost more than 72 hours for setting & registering nameservers and dns configurations. thanks,

    Read the article

  • Linux VLAN Bridge

    - by raspi
    I have home network with VLANs, one for LAN, one for WLAN and one for internet. I'd like to use bridging so that instead of configuring these same VLANs to every machine, they had own VLAN ID and bridges were LAN, WLAN and internet. I've tried it but for some reason keep-alive/ttl seems to get broken because SSH sessions etc suddenly disconnects. We have this same setup working in workplace for 4+ years with 100+ customers but it's custom firewall/router hardware so accessing it is impossible. I know that it runs Linux. So what is Debian/Ubuntu default network settings doing wrong or is it just NIC driver/hw problem? I've tried to mess araund with ttl etc settings without any luck. The bad stuff is happening in the bridge because current VLAN-only setup works fine. interfaces: auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 allow-hotplug eth1 iface eth0 inet static iface eth1 inet static auto vlan111 auto vlan222 auto vlan333 auto vlan444 auto br0 auto br1 auto br2 # LAN iface vlan111 inet static vlan_raw_device eth0 # WLAN iface vlan222 inet static vlan_raw_device eth0 # ADSL Modem iface vlan333 inet static vlan_raw_device eth1 # Internet iface vlan444 inet static vlan_raw_device eth0 # LAN bridge iface br0 inet static address 192.168.0.1 netmask 255.255.255.0 bridge_ports eth0.111 bridge_stp on # Internet bridge iface br1 inet static address x.x.x.x netmask x.x.x.x gateway x.x.x.x bridge_ports eth1.333 eth0.444 bridge_stp on post-up iptables -t nat -A POSTROUTING -o br1 -j MASQUERADE pre-down iptables -t nat -D POSTROUTING -o br1 -j MASQUERADE # WLAN bridge iface br2 inet static address 192.168.1.1 netmask 255.255.255.0 bridge_ports eth0.222 bridge_stp on Sysctl: net.ipv4.conf.default.forwarding=1

    Read the article

  • Routing table on Linux not respected

    - by MRHaarmann
    I have a very specific problem, building a Linux VPN endpoint (with external VPN Gateway), which should route certain networks over the tunnel, others via default gateway. The Linux VPN should do a NAT on the outgoing connections for the VPN peers. Setup is as following: Internet gateway LAN 192.168.25.1/24 VPN Gateway LAN 10.45.99.2/24 (VPN tunnel 10.45.99.1 to net 87.115.17.40/29, separate connection to Internet) Linux VPN Router eth0 192.168.25.71/24 eth0:503 10.45.99.1/24 Default 192.168.25.1 route to 87.115.17.40/29 via 10.45.99.2 (send_redirects disabled, ip_forward enabled) Linux clients (multiple): eth0 192.168.25.x/24 Default 192.168.25.1 route to 87.115.17.40/29 via 192.168.25.71 Ping to the machines via tunnel from the VPN Router is working. Now I want to establish a routing from my clients over the VPN gateway and the client packet gets routed to 192.168.25.1 ! traceroute output shows the packets get routed to 192.168.25.71, but then to 192.168.25.1. So the route is not respected in forward ! IPTables and Routing: ip route show 87.115.17.40/29 via 10.45.99.2 dev eth0 10.45.99.0/24 dev eth0 proto kernel scope link src 10.45.99.1 192.168.25.0/24 dev eth0 proto kernel scope link src 192.168.25.71 default via 192.168.25.1 dev eth0 iptables -A INPUT -i eth0:503 -j REJECT iptables -t nat -A POSTROUTING -o eth0:503 -j MASQUERADE iptables -A FORWARD -i eth0:503 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 192.168.25.0/24 -o eth0:503 -j ACCEPT So what is wrong with my setup ? The route is chosen correctly from localhost, but all the clients get forwarded to the Internet GW. thanks for helping, Marcus

    Read the article

  • UDP blocked by Windows XP Firewall when sending to local machine

    - by user36367
    I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: Windows XP Professional with Service Pack 3, all updated Program that sends UDP datagrams Program that receives UDP datagrams Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas?

    Read the article

  • Automating first time login process in Windows Server 2008 R2 SP1 virtual machine

    - by George Durzi
    I have a set of Windows 2008 Server R2 SP1 Enterprise Edition virtual machines running in Hyper-V. The host server has 64GB of RAM and two SSD drives (one drive for the host OS, and the second one for the VMs). The virtual machines are as follows: Domain Controller: 4GB RAM Exchange Server: 4GB RAM Terminal Services: 50GB RAM We use this setup for a travelling training class where users remote desktop to one of the VMs - let's call it the Terminal Services or "TS" VM - where tools such as Visual Studio are installed. The students go through some labs on the TS VMs in Visual Studio. Overall, this setup works great. However, when users are collectively logging in for the first time, the VM really struggles to keep up while all the user profiles are created. It can take some users up to 10 minutes to login. The number varies from 30 to 40 students. A workaround to this would be to manually remote desktop to the TS virtual machine using all the accounts to ensure that the local profile is created in advance. I'm looking for a way to automate the first time login process on the TS virtual machine. I am envisioning iterating through the accounts in a certain Active Directory OU, and then somehow initiating a remote desktop session to the TS VM to log them in for the first time. Are there ways to do this? Thanks

    Read the article

  • GlusterFS as elastic file storage?

    - by Christopher Vanderlinden
    Is there any way to run GlusterFS in a replicated mode, but with the ability to dynamically scale the volume up and down? Say you have 3 servers all running glusterd. your Gluster volume would have to be setup with replica 3 gluster volume create test-volume replica 3 192.168.0.150:/test-volume 192.168.0.151:/test-volume 192.168.0.152:/test-volume You would then mount it as say \mnt\gfs_test What happens when I want to add 2 more servers to the storage pool and then also use them in this volume? Is there any easy way to expand the volume AND increase that replica count to 5? My end goal is to run this on EC2 instances, say 3 Apache front ends, with the webroot setup on the gluster volume mount. My concern is that if I ever need to spin up a server, I would want the server to not only be an additional Apache front end, but also another server in the gluster file system, adding to fault tolerance as well as possibly giving a slight boost in read speed. Maybe there are better options that would fit the bill here? Thanks.

    Read the article

  • UDP blocked by Windows XP Firewall when sending to local machine

    - by user36367
    Hi there, I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: - Windows XP Professional with Service Pack 3, all updated - Program that sends UDP datagrams - Program that receives UDP datagrams - Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas? Thanks in advance!

    Read the article

  • MySQL ODBC + SSL with only the SSL Cipher option?

    - by sdek
    Does anybody know how I can have an SSL encrypted connection over MySQL ODBC without the cert options? So I asked my web host to setup a MySQL+SSL connection so that we can access our website's database via ODBC or MySQL Query Browser (or the likes). I am able to get an encrypted connection with the standard mysql client and MySQL Query Browser, but I can't get the ODBC connection to work. Looking for a little help... The way they set it up is a little different from the way I have read about on the interweb. The host didn't setup a cert, or at least I don't think so - I don't need to specify any cert options in my connection. I just need to specify the ssl cipher. Here is how I connect with the mysql client: mysql -h myhost.com -u myuser --ssl-cipher=3DES -p That works to get an encrypted connection. At least I am pretty sure it works because when I run mysql> \s I get SSL: Cipher in use is EDH-RSA-DES-CBC3-SHA Also, when I put EDH-RSA-DES-CBC3-SHA into the SSL Cipher field of MySQL Query Browser (without specifying any other SSL options) it connects just fine. But then when I try to do the same thing with my MySQL ODBC 3.5.1 and 5.1 I get a generic error. Here is the error from the 5.1 Driver. Connection Failed: [HY000] [MySQL][ODBC 5.1 Driver]SSL connection error

    Read the article

  • Windows 7 - media sharing extremely flakey (XBox 360)

    - by Nathan Ridley
    I have constant headaches with Windows Media Library sharing, which I'm using to share my video library (a whole lot of AVI files on my computer's hard drive) with the XBox 360. I have the whole setup working, so setup and basic configuration is not an issue. The issue is that Windows Media Library frequently fails to notice additions and modifications to the "watched" folders. Not only that, but often after I've added something new to the library, it fails to transmit this new library information to the 360, as is demonstrated by the fact that, using that 360, I navigate to my video library and the new folders don't show up in the list. Often the only way to get the 360 to see the changes is to exit out of "Videos" on the 360, then remove all videos from Windows Media Library, go back into videos on the 360 to confirm that nothing is shared, then re-add a few videos (but not too many) in Windows Media Library, then go back into the videos in the 360. The whole thing is a real pain in the bum and I really wish I could just add all my videos to Windows Media Library and have it keep watch without me having to kick it, and have the 360 pick up changes without me having to constantly rebuild the library. Any ideas?

    Read the article

  • Virtualizing an Inline network appliance with VirtualBox (or VMWare)

    - by Tzury Bar Yochay
    My device, which is a Linux based IP in-liner is transparent to the network peripherals, that is, no IP address assigned to any of its interfaces. For the sake of the conversation, let's use ADSL connection as an example, while the device is inspecting the bi-directional traffic, the network is behaving same as if device was not there, attached to the wire (see Physical setup at the attached diagram). I wonder if I can enclosed that "device" within a Windows machine and have it operated virtually so it still seats inline between the ADSL router and the Windows netwroking interface by using virtual NICs, (or whatever their name is in windows), and inspecting the traffic, same as if it was on a separate physical device, the drawing under "Virtual Setup" in the attached diagram show what I am trying to achieve. Reading a bit on the VirtualBox docs, seems like binding the right side is relatively simple, perhaps I should have one network adapter set as Bridge Networking and VirtualBox will connect it to the physical NIC on the host machine, and network packets are exchanged directly, circumventing the host operating system's network stack (WinXP in my case). However, I have no idea how to achieve the left side of my diagram, which requires adding virtual NICs to windows and configure them correctly in a way to make that pipeline possible. I would appreciate any help. by the way, if that is not possible with VirtualBox but with other virtualization solution (e.g. VMWare), I would accept the other as well.

    Read the article

  • IIS 6 ASP.NET default handler-mappings and virtual directories

    - by Mark Lauter
    I'm having a problem with setting a default mapping in IIS 6. I want to secure *.HTML files with ASP.NET forms authentication. The problem seems to have something to do with using virtual directories to hold the html files. Here's how it's setup: sample directory tree c:/inetpub/ (nothing in here) d:/web_files/my_web_apps d:/web_files/my_web_apps/app1/ d:/web_files/my_web_apps/app2/ d:/web_files/my_web_apps/html_files/ app1 and app2 both access the same html_files directory, so html_files is set as a virtual directory in the web apps in IIS... sample web directory tree //app1/html_files/ (points to physical directory: d:/web_files/my_web_apps/html_files/) //app2/html_files/ (points to physical directory: d:/web_files/my_web_apps/html_files/) If I put a file called test.html in the root of //app1/ and then add the default mapping to the asp.net dll and setup my security on the root folder with deny="?", then accessing test.html works exactly as expected. If I'm not authenticated, it takes me to the login.aspx page, and if I am authenticated then it displays test.html. If I put the test.html file in the html_files directory I get a totally different behavior. Now the login.aspx page loads and I stuck some code in to check if I was still authenticated: <p>autheticated: <%=User.Identity.IsAuthenticated%></p> I figured it would say false because why else would it bother to load the login page? Nope, it says true - so it knows i'm authenticated, but it won't give me access to the test.html file. I've spent several hours on this and haven't been able to solve it. I'm going to spend some more time on google to see if I've missed something. Fingers crossed.

    Read the article

  • TC hashing filters - single rule deletion

    - by exa
    For traffic shaping I'm currently using a setup that looks exactly like the setup from LARTC, on this page: http://lartc.org/howto/lartc.adv-filter.hashing.html I have a simple problem with that - everytime I want to modify something in the hash table (like assign a IP to different flowid), I need to delete the whole filter table and add it again filter by filter. (I actually don't do it by hand, I have a nice program that does it for me... but still...) There is a problem - I got roughly 10k filters allocated this way and deleting and refilling the whole filtertable can get pretty lengthy, which is not exactly good for traffic shaping. My program could easily manage to delete only the rules that need to be deleted (thus reducing the whole problem to several commands and miliseconds), but I simply don't know the command that deletes only the one hashing rule. My tc filter show: filter parent 1: protocol ip pref 1 u32 filter parent 1: protocol ip pref 1 u32 fh 2: ht divisor 256 filter parent 1: protocol ip pref 1 u32 fh 2:a:800 order 2048 key ht 2 bkt a flowid 1:101 match 0a0a0a0a/ffffffff at 16 filter parent 1: protocol ip pref 1 u32 fh 2:c:800 order 2048 key ht 2 bkt c flowid 1:102 match 0a0a0a0c/ffffffff at 16 filter parent 1: protocol ip pref 1 u32 fh 800: ht divisor 1 filter parent 1: protocol ip pref 1 u32 fh 800::800 order 2048 key ht 800 bkt 0 link 2: match 00000000/00000000 at 16 hash mask 000000ff at 16 The wish: 'tc filter del ...' command that removes only one specific filter (for example the 0a0a0a0a IP match (IP address 10.10.10.10)). Removal of some small subgroup would also be good - for example I could still recreate a bucket (bkt a) pretty fast. My attempts: I tried to number all the filters using prio, but with no help -- they just create something unusuable (but deletable) below, but the bucketed filters remain there after that gets deleted. Any ideas? edit - I'm adding a simplified tl;dr description of the problem: I created hash filter on some interfce just like in this http://lartc.org/howto/lartc.adv-filter.hashing.html I want to find a command that deletes one rule (e.g. 1.2.1.123) from the table, leaving the rest untouched and working.

    Read the article

< Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >