Search Results

Search found 4884 results on 196 pages for 'ad hoc distribution'.

Page 164/196 | < Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Patch management on multiple systems

  - by Pierre

  I'm in charge of auditing the security configuration of an important farm of Unix servers. So far, I came up with a way to assess the basic configuration but not the installed updates. The very problem here is that I just can't trust the package management tools on those machine. Indeed some of them did not sync with the repository for a long time (So I can't do a "yum check-updates" on Redhat for example). Some of those servers are not even connected to the internet and use an company repository. Another problem is that I have multiple target systems: AIX, Debian, Centos/Redhat, etc... So the version could be different (AIX) and the tools available will be different. And, last but not least, I can't install anything on the target system. So I need to use a script to retrieve the information and either: process it directly or save the information to be able to process it later on a server (Which may happen to run a different distribution than the one on which the information have been retrieved). The best ideas I could come up with were: either retrieve the list of installed packages on the machine (dpkg -l for example on debian) and process it on a dedicated server (Directly parsing the "Packages" file of debian repositories). Still, the problem remains the same for AIX and Redhat... or use Nessus' scripts to assess vulnerability on the installed packages, but I find this a bit dirty. Does anyone know any better/efficient way of doing this ? P.S: I already took time to review some answers to similar problems. Unfortunately Chef, puppet, ... don't meet the requirements I have to meet. Edit: Long story short. I need to have the list of missing updates on a Unix system just like MBSA on Windows. I'm not authorized to install anything on this system as it's not mine. All I have are scripts languages. Thanks.

  Read the article

• DD-WRT Acces Point as a Router

  - by Dzh

  Following suggestion to this question asked on Network Engineering, I am asking the question here. this is an extension to my previous question (I think it was deleted), where I was claiming that DDWRT was disabling it's DHCP server once connected to the network. I was wrong, as it now seems that it is bridging itself with another parallel connected wireless router. I have two Draytek 2820 and one Netgear WG602v3 with latest DDWRT. Lets call one wired-Draytek and it has wireless disabled. The other one, let's call it wireless-Draytek, is connected to wired-Draytek and has wireless with MAC filtering enabled. Once I connect Netgear to the wired-Draytek, the client that connects to Netgear, will be assigned with IP address from the wireless-Draytek. If the MAC address is not on the wireles-Draytek, the client is unable to obtain IP address and has no connectivity at all, even with manually assigned static IP configuration. To illustrate further, this is how network is set up: wired-Draytek ---------- wireless-Draytek \_________ Netgear What I wish to have, is that Netgear issues IP addresses from it's own IP pool and ignores the MAC filtering rules from wireless-Draytek. This is kind of puzzling how this they are bridging (if they are) themselves automatically. Thanks. UPDATE: It's not a home network. I gave you a bit simplified set-up. If there is a better site on Stack Exchange to ask this, please let me know. The Drayteks are running stock firmware, it's only Netgear that I've flashed to get more stability. In addition to these routers, I have also three 3COM Baseline switch 2824, and another Draytek router with Prosafe FS752TP PoE switch dedicated for VoIP phones. Wired-Draytek has IP 10.0.0.1, DHCP disabled as there is AD DC which is issuing IP addresses. Wireless-Draytek has IP 1.1.1.1 and DHCP enabled. Netgear has default - 192.168.1.1. As per suggestion, the specific question is - how do I isolate these two wireless routers?

  Read the article

• Server 2003 and SSL Certificates

  - by Keith Stokes

  I have a Windows 2000 domain with dozens of Windows 2000 servers and a few 2003 servers. Each server runs a custom app talking to a 3rd party utilizing self-signed certificates. To help troubleshooting we've created a custom test app. The 2000 servers are able to talk within seconds. The 2003 servers take anywhere from 10-30 seconds using a domain account and much less, usually under 5 seconds using a local account. The only exception to the local account performance is a new account, which is slow initially then faster. If you leave the test app open and reconnect repeatedly it talks in seconds. If you leave it open for sometime between 1 and 2 hours, it reverts back to the previous 10 seconds, so obviously something is caching. Installing the destination certificates in the local 2003 server store makes no difference. I've installed the certificates in AD and that apparently makes domain accounts work in 9-12 seconds, vs 30 seconds that was regular before. Manually clearing the certificate store on the 2003 server makes no difference. I'm at a loss as to where the certs might be cached and if I'm using some sort of domain certificate store that's hiding from me.

  Read the article

• Printer Naming Conventions

  - by John

  I am working on building a new AD print server and have been pondering the idea of renaming the printers. Right now we have a mix of names that varies between a mashup of some that reference location, some that reference functional area, and some that are rather generic. Some examples include the following: Dell 5210 - Building Name HP 4350 - Functional Area Dell Color 3100 - Location and Building Number HP 6500 - Mailroom I was curious what other people used to name their printers with. What conventions do you use and how to design a method that will be able to be used for a while without needing to rename them all again. Also, the naming methodology needs to be understandable for regular computing users so that they can relatively easily find the printer that they need. I was looking at some ideas from here, but I was not sure how practical some of them are. Any help that you can provide is appreciated. Note: I have reviewed many of the postings on here in relation to server naming conventions and found that they were not specific enough for the use case I present above.

  Read the article

• Distributed storage and computing

  - by Tim van Elteren

  Dear Serverfault community, After researching a number of distributed file systems for deployment in a production environment with the main purpose of performing both batch and real-time distributed computing I've identified the following list as potential candidates, mainly on maturity, license and support: Ceph Lustre GlusterFS HDFS FhGFS MooseFS XtreemFS The key properties that our system should exhibit: an open source, liberally licensed, yet production ready, e.g. a mature, reliable, community and commercially supported solution; ability to run on commodity hardware, preferably be designed for it; provide high availability of the data with the most focus on reads; high scalability, so operation over multiple data centres, possibly on a global scale; removal of single points of failure with the use of replication and distribution of (meta-)data, e.g. provide fault-tolerance. The sensitivity points that were identified, and resulted in the following questions, are: transparency to the processing layer / application with respect to data locality, e.g. know where data is physically located on a server level, mainly for resource allocation and fast processing, high performance, how can this be accomplished? Do you from experience know what solutions provide this transparency and to what extent? posix compliance, or conformance, is mentioned on the wiki pages of most of the above listed solutions. The question here mainly is, how relevant is support for the posix standard? Hadoop for example isn't posix compliant by design, what are the pro's and con's? what about the difference between synchronous and asynchronous opeartion of a distributed file system. Though a synchronous distributed file system has the preference because of reliability it also imposes certain limitations with respect to scalability. What would be, from your expertise, the way to go on this? I'm looking forward to your replies. Thanks in advance! :) With kind regards, Tim van Elteren

  Read the article

• Using Active Directory through a Firewall

  - by Adam Brand

  I had kind of a weird setup today where I wanted to enable Windows Firewall on a Windows 2003 R2 SP2 computer that would act as an Active Directory Domain Controller. I didn't see one resource on the Internet that listed what would be required to do this, so I thought I'd list them here and see if anyone has anything to add/sees something that isn't necessary. Ports to Open with "subnet" scope: 42 | TCP | WINS (if you use it) 53 | TCP | DNS 53 | UDP | DNS 88 | TCP | Kerberos 88 | UDP | Kerberos 123 | UDP | NTP 135 | TCP | RPC 135 | UDP | RPC 137 | UDP | NetBIOS 138 | UDP | NetBIOS 139 | TCP | NetBIOS 389 | TCP | LDAP 389 | UDP | LDAP 445 | TCP | SMB 445 | UDP | SMB 636 | TCP | LDAPS 3268 | TCP | GC LDAP 3269 | TCP | GC LDAP Ports to Open with "Any" Scope (for DHCP) 67 | UDP | DHCP 2535 | UDP | DHCP ALSO You need to restrict RPC to use fixed ports instead of everything 1024. For that, you need to add two registry keys: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\NTDS\Parameters Registry value: TCP/IP Port Value type: REG_DWORD Value data: <-- pick a port like 1600 and put it here HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Netlogon\Parameters Registry value: DCTcpipPort Value type: REG_DWORD Value data: <-- pick another port like 1650 and put it here ...don't forget to add entries in the firewall to allow those in (TCP, Subnet scope). After doing all that, I was able to add a client computer to the AD domain (behind Windows Firewall) and log in successfully.

  Read the article

• 2008 SR2 Server Starts Then Fails to Initialize DNS

  - by ThaKidd

  Got a weird situation going on. Background: Just transferred Active Directory from a 2003 Server to 2008 SR2. Removed the 2003 server from AD but I have not upgraded Active Directory to 08 only yet. After the transition a problem started. Whenever I reboot the server and I log in, the DNS server is "stopping". After a few minutes it finishes and I can restart start it at that point. Once it is restarted, all services come up. Now I did try to install HyperV (this is a dev server btw). Once the reboot for HyperV, everything was screwed as in I could not ping anything. Uninstalled and had the DNS server issue. Screwed with IPv6 settings (which I am not using) and problem was resolved for a bit. Also installed an Intel Pro1000 card and had a bit of success with DNS; then it failed. Weird thing is, outside of an error in syslog stating that the DNS server failed to start, there is no specific error that is generated in either System or DNS Server logs. Ideas are much appreciated! Thanks in advance.

  Read the article

• Retrieve a user's Exchange database in powershell

  - by Paul

  Hey Everyone, I've scoured the interwebs for a few days now off and on to find this. I am creating a powershell script for email-enabling new user's(Exchange 2007). To give you a little background when we have a new hire, their AD account is created at our off-site helpdesk, but they don't create their email account. I'm trying to automate the process of mail-enabling the user which involves putting them in the same database as an existing user, disable imap pop activesync, and lastly email the requester of the ticket. I would like to just get prompted for the New User's name, User to Replicate(mailbox, storage group, database), and the person to email after it's been created. So if someone could just help with a command to Retrieve a user's Exchange database in powershell that would be great, but if people also want to help with my hacked up script please do so as well!!! Here is what I have so far: Write-output “ENTER THE FOLLOWING DETAILS” $DName = Read-Host “User Diplay Name" $RUser = Read-Host "Replicate User(Database Grab)" ***$RData = #get the Replicate user's mailbox database here*** $REmail = #either just use a Read-Host “Requester's Email address" or ask for Requester's name and pipe through their email address by digging for it w/ powershell Enable-Mailbox -Identity "$DName" -Database "$RData" Send-MailMessage -From "John Doe <[email protected]>" -To (put $REmail here which is the Requester's email) -Subject "Test Person's email account" -Body "Test Person's email account has been setup.`n`n`nJohn Doe`nGeneric Company`nSystems Administrator`nOffice: 123.456.7890`[email protected]" -SmtpServer genericexchange.exchange.com

  Read the article

• OARC's DNSSEC validating resolvers validate all my records but A records

  - by demize

  I have DNS set up with powerdns. It serves my DNS pretty well, and it AXFRs to other slaves. The slaves haven't yet updated to the most recent records, but that doesn't affect the validation, it would appear. Any record I can think of (AAAA, MX, TXT, even the CNAME for www) validates -- except for A records: dig @149.20.64.20 +dnssec www.demize95.com CNAME returns ;; flags: qr rd ra ad; QUERY: 1, ANSWER: 2, AUTHORITY: 5, ADDITIONAL: 7 while dig @149.20.64.20 +dnssec demize95.com A returns ;; flags: qr rd ra; QUERY: 1, ANSWER: 2, AUTHORITY: 5, ADDITIONAL: 7. The same happens with any other A record I have. I set up DNSSEC with pdnssec, and it does work for all the other records, but it's never validated for my A records. What's the problem here? Also, a side-note: I have to use ISC's DLV to create the chain of trust, since my domain registrar doesn't yet support sending the DS records to the com zone.

  Read the article

• Postfix + Exchange + ActiveDirectory; How to mix them

  - by itwb

  My client has got many sub-offices, and one head office. The headoffice has a domain name: business.com All users in the many sub-offices need to have a headoffice email address: [email protected] Anyone not in the head office will need the email forwarded to an external email address. All users in the head office will have their email delivered to Microsoft Exchange. Users are listed in Active Directory under two different OU's: HeadOffice or SubOffice. Is this something able to be configured? I've done some googling, but I can't find any examples or businesses set up this way. Edit: Postfix will accept all email, will need to determine to forward the email to an external account or alternatively have it delivered to MS Exchange. I've done some reading about MS Exchange and that you can 'mail-enable' contacts for forwarding - but I don't know if each AD account requires an Exchange CAL? The end goal is to forward email to external accounts to sub offices or accept email for head office. Maybe I don't need to worry about Postfix to perform this task..... http://www.windowsitpro.com/article/exchange-server-2010/exchange-server-licensing-some-of-your-questions-answered "What about client access licenses (CALs)? You need one CAL per user who will connect to Exchange. Although it might not be 100 percent precise, I prefer to think of it as one CAL per mailbox; there are exceptions for users outside your organization, automated tools that use mailboxes, and so on. Exchange doesn't enforce this limit, so it's on you to ensure that you have the correct number of CALs for the set of clients you support."

  Read the article

• Slow RDP after server joins domain

  - by Chris Grove

  We're having RDP issues with Amazon cloud servers that we recently joined to an Active Directory domain. The setup is: A local office network A virtual private cloud in Amazon An IPSec tunnel between the two networks A number of Windows 2008 R2 servers on both networks An AD domain (call it abc.net), with one domain controller in each network. The domain controllers are both new, fresh installs. Before we had the domain set up we had local accounts for the cloud computers which were used for RDP access. Our idea was to get all of the servers on to the domain so we could use domain logins instead of per-server local logins. Before the cloud servers were in the domain, RDP (from the office network or through a VPN to the cloud) worked great. After we joined the cloud servers to the domain, RDP from the office became very slow - a few minutes to log in, long frequent pauses when the interface is unresponsive, generally just a slow and frustrating experience. This is a problem regardless of whether a domain or local login is used for RDP. Oddly, when outside of the office network and connecting to the cloud directly with the VPN, RDP is still very responsive. Any idea why RDP from office to cloud is suddenly very slow after the cloud servers join the domain? What can I look at in our configuration to address this? Any help is greatly appreciated.

  Read the article

• Good HTTP Monitoring tools

  - by ffffff

  I look for HTTP to work with a Linux system server monitor tool every protocol. I know, and will not there be it in whom or a freeware? When, for example, I dump 80/tcp with a packet monitor to be concrete # tethereal -i ppp0 port 80 -x Capturing on ppp0 1244206390.030474 219.111.xx.xx -> 74.125.xx.xx HTTP GET /search?output=js&num=0&dt=1244206414703&client=pub-3031568651010206&q=Cagliari%20Flight&ad=n3&ie=utf8&oe=utf8&channel=0091594208&adtest=off HTTP/1.1 0000 00 04 02 00 00 00 00 00 00 00 00 00 00 00 08 00 ................ 0010 45 00 01 e5 ee 82 40 00 40 06 d2 b5 db 6f 02 5b E.....@[email protected].[ 0020 4a 7d 4f 93 d4 29 00 50 3e df 4c 63 4b 6b 42 e0 J}O..).P>.LcKkB Such output is provided, but there is too much unnecessary information such as an SYN packet or a header. What I want The IP address of the client and sending out character string(Get; the contents of the POST) Among the output character string of the server only as for the HTML (Content-Type:) I am what is chisel) of a thing of text/html. I can set a filter and am the best if only information wanting can accumulate in the log.

  Read the article

• How to set static ip address on vmware for NAT guest vms from an ubuntu Host dhcp server?

  - by javadba

  I need to configure various linux flavor NAT'ed guest vm's to have static ip addresses provided by the Ubuntu host. The vmware documentation punts on this topic, deferring to "see the man pages for your linux distribution". But the generic pages for "my linux distro" do not know about the special stuff for vmware e.g. vmnet8. Pointers from someone who just knows how to do this would be much appreciated. Here is the /etc/vmware/vmnet8/dhcpd/dhcpd.conf: allow unknown-clients; default-lease-time 1800; # default is 30 minutes max-lease-time 7200; # default is 2 hours subnet 192.168.238.0 netmask 255.255.255.0 { range 192.168.238.128 192.168.238.254; option broadcast-address 192.168.238.255; option domain-name-servers 192.168.238.2; option domain-name localdomain; default-lease-time 1800; # default is 30 minutes max-lease-time 7200; # default is 2 hours option netbios-name-servers 192.168.238.2; option routers 192.168.238.2; } host vmnet8 { hardware ethernet 00:50:56:C0:00:08; fixed-address 192.168.238.1; option domain-name-servers 0.0.0.0; option domain-name ""; option routers 0.0.0.0; } Fromt the dhcpd.conf documentation, we are supposed to add an entry for static hosts similar to the following: host mystatichostonee { hardware ethernet 00:20:6B:C7:9B:E4; fixed-address 192.168.238.101; } host mystatichosttwo { hardware ethernet 00:23:7a:C7:9c:F2; fixed-address 192.168.238.102; } But notice that the vmnet8 entry in the vmware-generated dhcpd.conf already is set to fixed-address. I don't know how to add the specifics for my hosts to that vmnet8 entry: do they become nested?

  Read the article

• Dual DC Time Service

  - by poconnor

  I believe I'm having an issue with my Domain Controllers and Time Server. On my back up DC, I keep seeing a warning stating "The time service has stopped advertising as a time source because the local clock is not synchronized." Does this mean that my backup DC believes it's a Time Server? My PDC should be the time server and I have gone through setting up the PDC as the time server. I was not around for the original setup of the time server with the old PDC and Backup DC. But I believe the old PDC was the time server so I setup the new PDC as the new time server, when I decommissioned the old PDC. Is it possible that the Backup DC was setup as the time server and it still thinks it's suppose to be giving out time to everyone? Registry for PDC has NTP Registry for Backup has NT5D5 Results of w32tm /monitor Getting AD DC list for default domain... Analyzing:delayoffset from DC1.local..com Stratum: 4 delayoffset from DC1.local..com Stratum: 3 Warning: Reverse name resolution is best effort. It may not be correct since RefID field in time packets differs across NTP implementations and may not be using IP addresses. DC2.local..com[192.168.1.8:123]: ICMP: 1ms NTP: -0.6349491s RefID: DC1.local..com [192.168.1.9] DC1.local..com *** PDC ***[192.168.1.9:123]: ICMP: 0ms NTP: +0.0000000s RefID: wwwco1test12.microsoft.com [65.55.21.20]

  Read the article

• Why database partitioning didn't work? Extract from thedailywtf.com

  - by questzen

  Original link. http://thedailywtf.com/Articles/The-Certified-DBA.aspx. Article summary: The DBA suggests an approach involving rigorous partitioning, 10 partitions per disk (3 actual disks and 3 raid). The stats show that the performance is non-optimal. Then the DBA suggests an alternative of 1 partition per disk (with more added disks). This also fails. The sys-admin then sets up a single disk, single partition and saves the day. The size of disks was not mentioned but given today,s typical disk sizes (of the order of 100 GB), the partitions ; would be huge, it surprises me that a single disk with all partitions outperformed. Initially I suspect that the data was segregated and hence faster reads. But how come the performance didn't degrade as time went by with all the inserts and updates happening? Saw this on reddit, but the explanation was by far spindle/platter centered. There was no mention in the article about this. Is there any other reason? I can only guess that the tables were using a incorrect hash distribution causing non-uniform allocation across disks (wrong partitioning); this would increase fetch times. Any thoughts?

  Read the article

• Spam or exchange issue?

  - by John

  I am getting an error message to unknow user on my domain. I would like to know is this just a phishing spam email or it was really send from our domain? I have changed our domain name to OURDOMAIN.COM I have Exchange 2010 installed. Body of the email is Delivery has failed to these recipients or distribution lists: sales The recipient's e-mail address was not found in the recipient's e-mail system. Microsoft Exchange will not try to redeliver this message for you. Please check the e-mail address and try resending this message, or provide the following diagnostic text to your system administrator. Sent by Microsoft Exchange Server 2007 Diagnostic information for administrators: Generating server: murraygroup.local [email protected] #550 5.1.1 RESOLVER.ADR.RecipNotFound; not found ## Original message headers: Received: from ironport.mih.co.uk (10.10.29.9) by mih-exca-01.murraygroup.local (10.10.29.133) with Microsoft SMTP Server id 8.3.106.1; Fri, 29 Jun 2012 12:36:12 +0100 Received: from glamf04.netintelligence.com (HELO mailfilter.iomart.com) ([62.128.193.114]) by ironport.mih.co.uk with SMTP; 29 Jun 2012 12:42:48 +0100 Received: from glamta4.netintelligence.com(localhost.localdomain[127.0.0.1]) by mailfilter.iomart.com ; Fri, 29 Jun 2012 12:37:18 BST Received: from [195.43.137.66] ([195.43.137.66]) by glamta4.netintelligence.com (8.13.1/8.12.8) with ESMTP id q5TBbH4j022142 for <[email protected]>; Fri, 29 Jun 2012 12:37:18 +0100 Date: Fri, 29 Jun 2012 12:37:17 +0100 Message-ID: <20120629145229.4C2A817231D8A7958044@SONW> From: Ines Hampton <[email protected]> To: sales <[email protected]> Reply-To: Marguerite Soto <[email protected]> Subject: User sales MIME-Version: 1.0 Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: 7bit Return-Path: [email protected] eporting-MTA: dns;murraygroup.local Received-From-MTA: dns;ironport.mih.co.uk Arrival-Date: Fri, 29 Jun 2012 11:36:12 +0000 Final-Recipient: rfc822;[email protected] Action: failed Status: 5.1.1 Diagnostic-Code: smtp;550 5.1.1 RESOLVER.ADR.RecipNotFound; not found X-Display-Name: sales

  Read the article

• Implications of Multiple JobTracker nodes in a Hadoop cluster?

  - by Jim Dennis

  I get the impression that one can, potentially, have multiple JobTracker nodes configured to share the same set of MR (TaskTracker) nodes. I know that, conventionally, all the nodes in a Hadoop cluster should have the same set of configuration files (conventionally under /etc/hadoop/conf/ --- at least for the Cloudera Distribution of Hadoop (CDH). Can we define multiple Job Trackers in mapred-site.xml? Something like: <configuration> <property> <name>mapred.job.tracker</name> <value>jt01.mydomain.not:8021</value> </property> <property> <name>mapred.job.tracker</name> <value>jt02.mydomain.not:8021</value> </property> ... </configuration> Or is there some other allowed syntax for this? What are the implications of doing this. Does each JobTracker get information about the load on each TaskTracker node. In other words can the two JobTracker co-ordinated their scheduling across the TT nodes only based on the gossip information from the TTs or would they need to talk to one another? Is this documented anywhere?

  Read the article

• postfix test and configuration problem

  - by Woho87

  Hi Guys! I installed postfix using sudo yum install postfix postfix-mysql. I'm newbie to mail systems, but I have one AMAZON EC2 instance with a public DNS. I used the public DNS in most cases, when I configured the file main.cf. The public DNS I have is from amazon and it is a long string(ec2-123-34-234-677.....amazon.com). // I configured this on main.cf. I replaced example.com with ec2-123-.......amazon.com myhostname = mail.example.com mydomain = example.com myorigin = $mydomain mydestination = example.com, $transport_maps local_recipient_maps = $alias_maps $virtual_mailbox_maps unix:passwd.byname home_mailbox = Maildir/ How do I test postfix? I just want it to send emails for my web application. I tried to test it with >telnet localhost 25 after I typed in SSH >sudo postfix start. but I recieve the message that telnet command can not be found. I also use the Amazon linux distribution if you want to know. I use it because it is free. What have I done wrong? Are there anymore configurations required pls help!

  Read the article

• Uninstallation of WSUS form SBS 2008

  - by Logik

  I am not much experienced system admin, but i came across the client who was having SBS 2008. The server was running out of HDD space. So to recover some, I removed its WSUS role (twas not needed).this removed WSUS 3.0 SP1 & freed a lot of space. This SBS is: Domian controller, DNS, DHCP, File server. After i removed WSUS i disabled windows update service & i rebooted serer & checked from one of client if the shared folders are accessible. they were. Next day all of sudden i got call from them saying they can't login into their domain. I looked into server, the Active directory service was stopped. I never remember touching any service other than windows update. How come AD service stopped running all of sudden. Is removing WSUS have such impact? I am not aware of any such thing.

  Read the article

• Connecting to Server 2008 shares fails

  - by Chris J

  I'm having problems getting a reliable share working on an x64 Server 2008 R1 SP1 server. All works well after a reboot, but after some time (within a day) the shares become unavailable to XP and Server 2003 servers. Interestingly, they remain available to other Server 2008 servers. On trying to access \\server\share, Server 2003 returns immediately and simply gives me the message "The specified network name is no longer available", XP takes a minute or two to timeout before giving the same message. There doesn't seem to be anything in the event logs indicating a problem. Doing some googling over the last day or two I've seen the following blamed: Bad network drivers ... I've updated to the latest drivers with no result Symantec anti-virus ... we're not using it (currently no AV on the server) Receive window auto-tuning ... I've disabled with netsh int tcp set global autotuninglevel=disabled and netsh int tcp set global rss=disabled None of these have had an effect. Windows Firewall is currently disabled. As other Server 2008 boxes (both x32 and x64) can connect, I can only assume that there's some new security configuration that's not quite right - or there's an AD issue that I need to trace, but don't know where to start. Even if anyone doesn't know how to resolve, if someone knows what I need to look for with Wireshark this would be a help.

  Read the article

• Enable bitlocker an save key to share

  - by user273694

  I have searched all over the web but cannot find a complete answer to this: How to enable Bitlocker on a laptop with TPM, and store a file with the Bitlocker recovery key and TPM password by USING THE manage-bde command line tool. The file should be the same as when created in the Bitlocker manager UI. I DO NOT want to save to AD. The same question was asked here but was not answered correctly. The goal is to write a script to be used with an endpoint manager. I have tried the following: manage-bde -on C: Works fine, but does not create or save a key. manage-bde -on C: -rk C:\myfolder\ and manage-bde -on C: -RecoveryKey C:\myfolder\ -rp The output from the last two methods state that a key has been saved to c:\myfolder and so on, but that is not the case. It also says that I have to: Save the password in a secure location Insert a USB flash drive with an external key file into the computer. Restart and run hardware test type "manage-bde -status" to check if the hardware test succeeded After a restart, I get an error saying that Bitlocker could not be enabled because the bitlocker startup key or recovery kpassword cannot be found on the USB device.... C: was not encrypted. Why am I asked to insert a USB?? I simply want to encrypt the hard drive and save the recovery information to a file automatically. Is that too much to ask? Help please!

  Read the article

• 2012 R2 services will not start after promotion to Domain Controller

  - by Cybersylum

  Having a peculiar issue promoting a Windows 2012 R2 server in a domain at 2003 domain/forest functional level. Built a new 2012 R2 server, added the following software (labtech, appassure, eset A/V, & Teamviewer). It activated and appeared to be working fine. I added the Active Directory Domain Services role, and completed the configuration (Domain/Forest Prep, and DC promotion). All appeared to go well. I rebooted the server, and that's where the peculiar stuff began. I noticed the server indicated it needed activated again; but would not accept the key. I verified the key was good. That's when I noticed the Software Protection service (as well as many other core services - Base Filtering engine, DHCP client, firewall, etc) would not start. The error message for all of them was "Access Denied". I called MS, and they wanted to troubleshoot at a service level. Their fix was to use procmon and identify the resource that needed permissions (registry key, file or folder) and add "everyone" with full control). That got the services to start; but the problem re-appeared after a reboot. Thinking the issue might have been with the anti-virus package during the promotion process, I rebuilt the DCs from scratch and removed the metadata from AD (as I could not demote the machines "rpc server unavailble"). I tried to promote the newly built machines again. The only changes to the brand new machines being critical updates. Again the promotion appeared to work fine; but upon reboot (and a long wait to allow replication to occur) similar problems began to re-appear. I have verified that the schema updates are correct (schema version is 69 - for Windows 2012 R2). I am not finding much about this issue through my own searches, so I thought I would post this to see if anyone else has seen anything similar...

  Read the article

• Only one domain is not resolving via Windows DNS server at multiple locations, but is at others

  - by Brett G

  I'm having quite a weird issue. Had mail delivery issues to a specific domain. After looking closer, I realized that the DNS for that domain isn't resolving via the in-house Windows 2003 SP2 DNS server. C:\>nslookup foodmix.net Server: DC.DOMAIN.com Address: 10.1.1.1 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to DC.DOMAIN.com timed-out (DC.DOMAIN.com and 10.1.1.1 are generic values to replace the actual ones) Even if I run this nslookup from the DC.DOMAIN.com server, I get the same result. However, all other requests are working as they should. I had a sysadmin friend try this DNS lookup on servers at several companies that he consults for (which are also Windows 2003 AD servers). The weird thing is some of these were having the same exact issue. However using public DNS servers work. I have tried clearing the DNS cache, restarting the server, restarting the services, etc. Nothing has worked. One weird event I noticed in the DNS Server Event Logs that might be related is an event ID of 5504 with the following description: The DNS server encountered an invalid domain name in a packet from 192.33.4.12. The packet will be rejected. The event data contains the DNS packet. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. In the data section below, I can see the following mentioned: ns2.webhostingstar.com Which happens to be the nameserver for the domain in question. Several discussion threads and a MS KB have pointed to disabling EDNS. I have done this via "dnscmd /config /enableednsprobes 0" and it has not fixed the issue.

  Read the article

• How can I inject clips [ads] in a playlist every x minutes (even if previous clip is not over)

  - by azera

  Sorry for the title, I find it quite hard to describe what I want to do in a single sentence We have a few TV here linked to our computer, which we use to display clips about what we do in our sport center, what you should do to stay in good form ect ... It's running non stop, actually though vlc + playlist. Those main clips are 1-2 hours long and we have about 20 of them looping randomly all day. We would like to inject ads for some of our sponsiored products every now and then during the playlist, like say one ad every 15 minute. Does any one know how we can do that, while keeping the main clip random order ? I thought about encoding the whole thing as a single movie with ads inserted, but then it's not random. So we can put the ads in the playlist itself right ? Except clips are several hours long and we want that more often than that. Cutting the main clips in several pieces seems to work but that kind of sucks as new clips are made every month. If any one has an idea, thanks a lot

  Read the article

< Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >