Search Results

Search found 5346 results on 214 pages for 'before filter'.

Page 164/214 | < Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >

• Windows Server 2008 DHCP with RRAS

  - by Guillermo Prandi

  I have a Windows Server 2008 R2 which is a member of a domain, but is placed in a remote location. The server is directly connected to Internet. Clients need to access a particular insecure TCP service in this server (ports 9730 and 9731). Since clients have dynamic IP addresses I cannot know in advance, I thought it would be nice to have them connected through a VPN in order to access the insecure service, but ONLY to access that service, like this: Client ------> VPN TUNNEL ------> (Insecure service at Server) | \----> (Normal internet access) I'd enable the insecure ports in the firewall only from VPN accesses. For this I configured RRAS in the server and gave it a static IP address range (172.19.1.2 through 172.19.1.254) to serve the clients. First I thought I could use DHCP to assign the addresses, but I cannot use DHCP in my LAN connection (not allowed by the hosting service). I tried configuring DHCP binding it to a Microsoft Loopback Adapter, but that's not supported as a DHCP source by RRAS. What I want to accomplish is to send specific DHCP options to the client (network mask, routing table, etc.). In particular: Prevent the client from having the server as default router (without changing the client's "use default gateway in remote network"). Have it as a route for the server's internal RRAS address only (172.19.1.1). Prevent the client from using a 255.255.0.0 mask for the 172.19.x.x network (a 255.255.255.0 mask would be better). Can I do that with RRAS only? How? Currently, the only solution I can think of is to use DHCP in the LAN adapter, but filter DHCP packets so they don't reach the provider's network. However, I'm not sure if that will work. Any suggestions are welcomed! Guille

  Read the article

• Apache mod-pagespeed installation affects mod-spdy?

  - by tim peterson

  Recently my site (an https connection, running on an Amazon EC2 ubuntu apache2.2) has this issue where I need to load the page several times (3-4) before it will load normally without issue. It will then load normally as long as I keep loading pages regularly (every couple seconds). It will stall again if I don't load pages for a few minutes. It has nothing to do with my application because I don't have this problem with the exact same app codebase on my Apache installation on my laptop. The only things to my knowledge that I've changed is that I recently installed mod_spdy and then a few weeks later I installed mod_pagespeed, https://developers.google.com/speed/pagespeed/mod. However, I have since turned mod_pagespeed off by setting its pagespeed.conf to mod_pagespeed off. Unfortunately, that didn't solve the problem. The line below is how every of last 10 lines of my error.log look: # tail -f /var/log/apache2/error.log ... [32728:32729:ERROR:mod_spdy.cc(162)] request->chunked == 1 in request GET / HTTP/1.1 [Sat Jun 02 04:50:08 2012] [warn] [client 50.136.93.153] [stream 5] [32728:32729:WARNING:http_to_spdy_filter.cc(113)] HttpToSpdyFilter is not the last filter in the chain: chunk any thoughts? thank you, tim

  Read the article

• Endian Destination NAT

  - by Ben Swinburne

  I have installed Endian Community Firewall 2.3 and am clearly misunderstanding/doing something wrong with it. I'm trying to create some destination NAT rules to allow incoming connections to various services within the network. Router - RED I/F - x.x.x.x Router - GREEN I/F - 192.168.11.253 ECF - RED I/F - 192.168.11.254/24 ECF - GREEN I/F - 192.168.12.254/24 Target server - 192.168.12.1 Please ignore the haphazard choice of subnets and addresses- I'm trying to quickly plop Endian into an existing network before a complete rework in 6-12 months so for now. Everything works except destination NAT, so outgoing connections are fine, the routes between the two subnets are OK etc. I want to create various incoming NATs but let's take for the sake of argument, SMTP port 25 from the Internet to Target server 192.168.12.1. I've tried almost every combination of options in the Destination NAT section to achieve this and clearly am doing something wrong. I suspect my confusion must be somewhere in the Access From and/or Target section. The rest seems OK Filter Policy = Allow Service = SMTP Protocol = TCP Port = 25 Translate to type = IP DNAT Policy = NAT Insert IP = 192.168.12.1 Port Range = 25 Enabled = Checked Position = First I can't work out what I'm doing wrong, or am I doing it right and it's just not working!? Any help would be greatly appreciated.

  Read the article

• Best Firewall product for hosting/housing environment?

  - by Raffael Luthiger

  I am searching for a firewall product (appliance or software) for an hosting/housing environment. The biggest problem is that the rules get very complex as more customers are behind the firewall. Some have only one server, others have a whole subnet. Some need NAT, some a VPN endpoint. Some customers want to only allow port http, others ssh as well. So the device needs to be able to support VLANs and it should be possible to group the rules per customer. Speed is another important point. And being able to manage redundant devices easily. I am searching for something that doesn't have all the extras like spam filter etc. I was searching a lot on the net but either they had all those extras as well (and with is an overloaded configuration interface) or they missed some of the features I need (e.g. VLAN). The VPN endpoint is not the an important criteria. We were thinking about a separate machine for it.

  Read the article

• IP Tables won't save the rule.

  - by ArchUser

  Hello, I'm using ArchLinux and I have an IP tables rule that I know works (from my other server), and it's in /etc/iptables/iptables.rules, it's the only rule set in that directory. I run, /etc/rc.d/iptables save, then /etc/rc.d/iptables/restart, but when I do "iptables --list", I get ACCEPTs on INPUT,FORWARD & OUTPUT. # Generated by iptables-save v1.4.8 on Sat Jan 8 18:42:50 2011 *filter :INPUT DROP [0:0] :FORWARD DROP [0:0] :OUTPUT ACCEPT [216:14865] :BRUTEGUARD - [0:0] :interfaces - [0:0] :open - [0:0] -A INPUT -p icmp -m icmp --icmp-type 18 -j DROP -A INPUT -p icmp -m icmp --icmp-type 17 -j DROP -A INPUT -p icmp -m icmp --icmp-type 10 -j DROP -A INPUT -p icmp -m icmp --icmp-type 9 -j DROP -A INPUT -p icmp -m icmp --icmp-type 5 -j DROP -A INPUT -p icmp -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -j interfaces -A INPUT -j open -A INPUT -p tcp -j REJECT --reject-with tcp-reset -A INPUT -p udp -j REJECT --reject-with icmp-port-unreachable -A INPUT -p tcp -m tcp ! --tcp-flags FIN,SYN,RST,ACK SYN -m state --state NEW -j DROP -A INPUT -f -j DROP -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG FIN,SYN,RST,PSH,ACK,URG -j DROP -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG NONE -j DROP -A INPUT -i eth+ -p icmp -m icmp --icmp-type 8 -j DROP -A BRUTEGUARD -m recent --set --name BF --rsource -A BRUTEGUARD -m recent --update --seconds 600 --hitcount 20 --name BF --rsource -j LOG --log-prefix "[BRUTEFORCE ATTEMPT] " --log-level 6 -A BRUTEGUARD -m recent --update --seconds 600 --hitcount 20 --name BF --rsource -j DROP -A interfaces -i lo -j ACCEPT -A open -p tcp -m tcp --dport 80 -j ACCEPT -A open -p tcp -m tcp --dport 10011 -j ACCEPT -A open -p udp -m udp --dport 9987 -j ACCEPT -A open -p tcp -m tcp --dport 30033 -j ACCEPT -A open -p tcp -m tcp --dport 8000 -j ACCEPT -A open -p tcp -m tcp --dport 8001 -j ACCEPT -A open -s 76.119.125.61 -p tcp -m tcp --dport 21 -j ACCEPT -A open -s 76.119.125.61 -p tcp -m tcp --dport 3306 -j ACCEPT -A open -p tcp -m tcp --dport 22 -j BRUTEGUARD -A open -s 76.119.125.61 -p tcp -m tcp --dport 22 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT COMMIT # Completed on Sat Jan 8 18:42:50 2011

  Read the article

• Traffic Shaping using tc

  - by Simon

  Hi guys, I have a 1.5 Mbit/s link that i want to share with 150 users. My setup is the following: Linux box with 3 NICs eth0 - public ip eth1 - subnet A - 50 users (static ips) eth2 - subnet B - 100 users (via dhcp) I am using squid as a transparent proxy on port 3128. dhcp server using ports 67 and 68. I was creating, but I think packets are not going to the right queues #!/bin/bash DEV=eth0 RATE_MAIN=2048kbit CEIL_MAIN=2048kbit BURST=1b CBURST=1b RATE_DEFAULT=1024kbit CEIL_DEFAULT=$CEIL_MAIN PRIO_DEFAULT=3 RATE_P2P=1024Kbit CEIL_P2P=$CEIL_MAIN PRIO_P2P=4 RATE_IND=32kbit CEIL_IND=$CEIL_DEFAULT tc qdisc del dev $DEV root tc qdisc add dev $DEV root handle 1: htb default 30 tc class add dev $DEV parent 1: classid 1:1 htb rate $RATE_MAIN ceil $CEIL_MAIN tc class add dev $DEV parent 1:1 classid 1:10 htb rate $RATE_DEFAULT ceil $CEIL_MAIN burst $BURST cburst $CBURST prio $PRIO_WEB ## some other sub class for p2p other traffic tc class add dev $DEV parent 1:1 classid 1:20 htb rate $RATE_P2P ceil $CEIL_P2P burst $BURST cburst $CBURST prio $PRIO_P2P $IPS_NET1=50 $IPS_NET2=100 let $IPS=$IPS_NET1+$IPS_NET2 for ((i=1; i<= $IPS; i++)) do let CLASSID=($i+100) let HANDLE=($i+100) tc class add dev $DEV parent 1:10 classid 1:$CLASSID htb rate $RATE_IND ceil $CEIL_IND tc qdisc add dev $DEV parent 1:$CLASSID handle $HANDLE: sfq perturb 10 done ## Generate IP addresses ## IP_ADDRESSES="" # Subnet A BASE_IP=10.10.10. for ((i=2; i<=$IPS_NET1+1; i++)) do TEMP="$BASE_IP$i" IP=ADDRESSES="$IP_ADDRESSES $TEMP" done # Subnet B BASE_IP=192.168.0. for ((i=2; i<=$IPS_NET2+1; i++)) do TEMP="$BASE_IP$i" IP_ADDRESSES="$IP_ADDRESSES $TEMP" done ## FILTERS ## j=1 U32="tc filter add dev $DEV protocol ip parent 1:0 prio $PRIO_DEFAULT u32" for NET in $IP_ADDRESSES; do let CLASSID=($j+100) $U32_DEFAULT match ip src $NET/32 flowid 1:$CLASSID $U32_DEFAULT match ip dst $NET/32 flowid 1:$CLASSID let j=j+1 done Can you guys help me figure out what's wrong with it? basically I want my classes to be 1:1 (1.5 Mbit ) 1:10 (1024 Kbit) 1:20 (1024 Kbit) (200 ips each with 32 kbit)

  Read the article

• Split horizon, route filtering, and having RIPv2 announce a non-attached route to host

  - by Paul

  Routers A, B & C live at 10.1.1.1, 10.1.1.2 and 10.1.1.3 on a /24 metro Ethernet subnet. Each router also has its own private subnet on another interface. Router B's private subnet links thru a firewall to a 10.20.20.0 network at another organization. Router B redistributes to A and C several static routes for hosts on 10.20.20.0. However, a new host 10.20.20.5/32 must be reached via a different path that goes through router C. I know that C can advertise this host-based route with no problem, but I'd like to keep all my 10.20.20.x static routes in one place. So, how can B tell A via RIPv2 to send packets for 10.20.20.5/32 to C? So far it looks like I need no ip split-horizon on router B's 10.1.1.2 interface, perhaps because B has already learned from C other routes with a next hop of 10.1.1.3. But how does RIPv2 split horizon with no auto-summary and network 10.0.0.0 really work? If B learns a route to ANY 10.x.x.x network or host from A or C, is that enough for split horizon to keep it from redistributing ip route 10.20.20.5 255.255.255.255 10.1.1.3? And if I want to suspend split horizon only for this one new host, how do I filter out the mess of regurgitated routes that B advertises when I try no ip split-horizon? Thanks much.

  Read the article

• How can I make Mac OS X Address Book display a person’s home address from an LDAP server?

  - by Arcturus

  Hi, (I've posted this question on Stack Overflow first, but someone told me it belonged here.) I have a custom LDAP server, which I can customize to generate whichever object class and attributes I need. I'm trying to display people from that server in the Mac OS X address book. Names and organizations display correctly, as well as work-related phone and address. However, I've never been able to have a home address displayed in the address book. This is an example of output from running a ldapsearch: # extended LDIF # # LDAPv3 # base <dc=example,dc=com> with scope subtree # filter: (givenName=Joh*) # requesting: ALL # # 10041, example.com dn: uid=10041,dc=example,dc=com objectclass: top objectclass: person objectclass: organizationalPerson objectclass: inetOrgPerson objectclass: mozillaOrgPerson uid: 10041 cn: John Doe givenName: John sn: Doe o: Acme telephoneNumber: 500 00 00 mobile: 500 00 00 mail: [email protected] street: Baker St postalCode: 10098 l: New York c: US homePostalAddress: White St mozillaHomePostalCode: 10098 mozillaHomeLocalityName: New York mozillaHomeCountryName: US # search result search: 2 result: 0 Success # numResponses: 2 # numEntries: 1 Every piece of information shows up in the address book up to here: homePostalAddress: White St mozillaHomePostalCode: 10098 mozillaHomeLocalityName: New York mozillaHomeCountryName: US Which object class or attribute name should I use to have the home address show up in the Mac OS X address book?

  Read the article

• pfsense 2.0.1 Firewall SMB Share not showing up under network

  - by atrueresistance

  I have a freenas NAS with a SMB share running at 192.168.2.2 of a 192.168.2.0/28 network. Gateway is 192.168.2.1. Originally this was running on a switch with my LAN, but now having upgraded to new hardware the Freenas has it's own port on the firewall. Before the switch the freenas would show up under Network on a windows 7 box and an OSX Lion box as freenas{wins} or CIFS shares on freenas{osx} so I know it doesn't have anything do to with the freenas. Here are my pfsense rules. ID Proto Source Port Destination Port Gateway Queue Schedule Description PASS TCP FREENAS net * LAN net 139 (NetBIOS-SSN) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 389 (LDAP) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 445 (MS DS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 137 (NetBIOS-NS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 138 (NetBIOS-DGM) * none cifs lan passthrough BLOCK * FREENAS net * LAN net * * none BLOCK * FREENAS net * OPTZONE net * * none BLOCK * FREENAS net * 192.168.2.1 * * none PASS * FREENAS net * * * * none BLOCK * * * * * * none I can connect if I use \\192.168.2.2 and enter the correct login details. I would just like this to show up on the network. Nothing in the log seems to be blocked when I filter by 192.168.2.2. What port am I missing for SMB to show up under the network and not have to connect by IP? ps. Do I really need the LDAP rule?

  Read the article

• Dismount USB External Drive using powershell

  - by JC

  Hello, I am attempting to dismount an external USB drive using powershell and I cannot successfuly do this. The following script is what I use: #get the Win32Volume object representing the volume I wish to eject $drive = Get-WmiObject Win32_Volume -filter "DriveLetter = 'F:'" #call dismount on that object there by ejecting drive $drive.Dismount($Force , $Permanent) I then check my computer to check if drive is unmounted but it is now. The boolean parameters $force and $permanent have been tried with different permutations to no avail. The exit code returned by the dismount command changes when the params are toggled. (0,0) = exit code 0 (0,1) = exit code 2 (1,0) = exit code 0 (1,1) = exit code 2 The documentation for exit code 2 indicates that there are existing mount points as a reason why it cannot dismount. Although I am trying to dismount the only mount point that exists so I am unsure what this exit code is trying to tell me. Having already trawled the web for people experiencing similar problems I have only found one additional command to try and that is the following: # executed after the .Dismount() command $drive.Put() This additional command does not help. I am running out of things to try, so any assistance anyone can give me would be greatly appreciated, Thanks.

  Read the article

• Mail.app doesn't detect sender in Address Book

  - by CoreSandello

  Hi there. I don't understand, how does 'smart addresses' in Mail.app work. Recently I mentioned, that for some emails I don't see person's full name in 'From' column. I started to dig into this behavior and found out, that I have few contacts in my Address Book, that are not recognized by Mail.app. Here how it looks: I have a person in Address Book with filled email entry and filled first/last name (localized). I have an incoming email from that person (from email specified in Address Book), but first/last name in the email itself doesn't match with ones specified in Address Book (e. g. 'From' field in email looks like 'John [work] <[email protected]>' while Address Book entry is 'John Smith' (localized, in Russian)). And Mail.app doesn't recognize that this mail is originating from that person in Address Book: if I click on 'From' field, it suggests to me to add sender to Address Book, while for others' emails I have 'Show in Address Book' menu entry (especially for ones with full localized name in 'From' field). I'm wondering, is that behavior correct or I'm missing something? I'm using Snow Leopard & Mail 4.0; my system language set to English, if that matters. I'd like to have some clarifications on that Mail.app behavior: whenever it fixable or not (and if it's fixable, I'd like to see a fix). By the way, is it possible to match sender's address against Address Book entry in filter rules or not? That would be great, if I can create rules like 'move all mail from that person to that folder' without specifying exact source address. Thanks, Ivan.

  Read the article

• Authenticate users with Zimbra LDAP Server from other CentOS clients

  - by efesaid

  I'am wondering that how can integrate my database,web,backup etc.. centos servers with Zimbra LDAP Server. Does it require more advanced configuration than standart ldap authentication ? My zimbra server version is [zimbra@zimbra ~]$ zmcontrol -v Release 8.0.5_GA_5839.RHEL6_64_20130910123908 RHEL6_64 FOSS edition. My LDAP Server status is [zimbra@ldap ~]$ zmcontrol status Host ldap.domain.com ldap Running snmp Running stats Running zmconfigd Running I already installed nss-pam-ldapd packages to my servers. [root@www]# rpm -qa | grep ldap nss-pam-ldapd-0.7.5-18.2.el6_4.x86_64 apr-util-ldap-1.3.9-3.el6_0.1.x86_64 pam_ldap-185-11.el6.x86_64 openldap-2.4.23-32.el6_4.1.x86_64 My /etc/nslcd.conf is [root@www]# tail -n 7 /etc/nslcd.conf uid nslcd gid ldap # This comment prevents repeated auto-migration of settings. uri ldap://ldap.domain.com base dc=domain,dc=com binddn uid=zimbra,cn=admins,cn=zimbra bindpw **pass** ssl no tls_cacertdir /etc/openldap/cacerts When i run [root@www ~]# id username id: username: No such user But i am sure that username user exist on ldap server. EDIT : When i run ldapsearch command i got all result with credentials and dn. [root@www ~]# ldapsearch -H ldap://ldap.domain.com:389 -w **pass** -D uid=zimbra,cn=admins,cn=zimbra -x 'objectclass=*' # extended LDIF # # LDAPv3 # base <dc=domain,dc=com> (default) with scope subtree # filter: objectclass=* # requesting: ALL # # domain.com dn: dc=domain,dc=com zimbraDomainType: local zimbraDomainStatus: active . . .

  Read the article

• Laptops with easy heat sink service?

  - by Niten

  Can you recommend a current laptop model with easy heat sink access – or better yet, a removable air intake filter – making it easy to periodically clean out the dust and lint that always packs up in these things? Every laptop I've owned has eventually overheated on account of a clogged heat sink. (I suppose it doesn't help that I have a cat who loves to hang out where I'm working, or that my laptop is almost always running.) One of the things I really love about my current system, a Dell Inspiron 1420n, is how easy it is to service its cooling system: whenever I notice the fan starting to work harder and the CPU temperature climbing higher than it should be, I merely have to unscrew a single panel from the bottom of the machine, clean out the heat sink, and then I'm good for another few months. Which current models of the "business laptop" variety offer similar easy cooling system service? I'm looking for something roughly along the lines of: 14- or 15-inch display Nehalem-based CPU Solid construction – magnesium chassis or better (like the Inspiron) TPM (for BitLocker) ideal, but not mandatory Docking adapter ideal, but not mandatory Good battery life For example, the ThinkPad T410 would have been my top choice, but it seems like it would be a serious chore to service its heat sink. For the current MacBook Pros it looks downright impossible. No matter how nice the laptop is in other respects, it'll be of no use to me when it's overheating. So, any suggestions? Thanks in advance... (I'm constantly surprised that customers and manufacturers don't pay more attention to this feature, at least in the business laptop subcategory. In the last couple months I've fixed two friends' laptops which were also overheating due to clogged cooling systems; clearly I'm not the only one affected by this.)

  Read the article

• KVM Guest with NAT + Bridged networking

  - by Daniel

  I currently have a few KVM Guests on a dedicated server with bridged networking (this works) and i can successfully ping the outside ips i assign via ifconfig (in the guest). However, due to the fact i only have 5 public ipv4 ip addresses, i would like to port forward services like so: hostip:port - kvm_guest:port UPDATE I found out KVM comes with a "default" NAT interface, so added the virtual NIC to the Guest virsh configuration then configured it in the Guest, it has the ip address: 192.168.122.112 I can successfully ping 192.168.122.112 and access all ports on 192.168.122.112 from the KVM Host, so i tried to port forward like so: iptables -t nat -I PREROUTING -p tcp --dport 5222 -j DNAT --to-destination 192.168.122.112:2521 iptables -I FORWARD -m state -d 192.168.122.0/24 --state NEW,RELATED,ESTABLISHED -j ACCEPT telnet KVM_HOST_IP 5222 just hangs on "trying" telnet 192.168.122.112 2521 works [root@node1 ~]# tcpdump port 5222 tcpdump: WARNING: eth0: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 23:43:47.216181 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445777813 ecr 0,sackOK,eol], length 0 23:43:48.315747 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445778912 ecr 0,sackOK,eol], length 0 23:43:49.415606 IP 1.152.245.247.51183 > null.xmpp-client: Flags [S], seq 1183303931, win 65535, options [mss 1400,nop,wscale 3,nop,nop,TS val 445780010 ecr 0,sackOK,eol], length 0 7 packets received by filter 0 packets dropped by kernel [root@node1 ~]# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state NEW,RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT) target prot opt source destination All help is appreciated. Thanks.

  Read the article

• Error applying iptables rules using iptables-restore

  - by John Franic

  Hi I'm using Ubuntu 9.04 on a VPS. I'm getting an error if I apply a iptables rule. Here is what I have done. 1.Saved the existing rules iptables-save /etc/iptables.up.rules Created iptables.test.rules and add some rules to it nano /etc/iptables.test.rulesnano /etc/iptables.test.rules This is the rules I added *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -i ! lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections # # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE # -A INPUT -p tcp -m state --state NEW --dport 22- j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT After editing when I try to apply the rules by iptables-restore < /etc/iptables.test.rules I get the following error iptables-restore: line 42 failed Line 42 is COMMIT and I comment that out I get iptables-restore: COMMIT expected at line 43 I'm not sure what is the problem, it is expecting COMMIT but if COMMIT is there it's giving error. Could it be due to the fact i'm usin a VPS?My provider using OpenVZ for virtualizaton.

  Read the article

• Group Policy GPO not 'seen' at client

  - by fukawi2

  I have a new OU (natorg.local\NATO\Users) that I am trying to apply GP to. I have created a new user in this OU, and linked the 3 GPO's to this OU: DESKTOP - Folder Redirection (AppData) DESKTOP - Folder Redirection (Desktop) DESKTOP - Folder Redirection (Documents) Hopefully the names are sufficient to suggest what they do exactly. The settings are under User Settings so there is no Loopback processing required (if my understanding is correct). GP Modelling for the user and specific computer says that the GPOs will/should be applied, however on the client, gpresult doesn't even appear to see the GPOs under either "Applied" or "Not Applied": USER SETTINGS -------------- CN=Amir,OU=Users,OU=NATO,DC=natorg,DC=local Last time Group Policy was applied: 25/06/2012 at 11:07:13 AM Group Policy was applied from: svr-addc-01.natorg.local Group Policy slow link threshold: 500 kbps Applied Group Policy Objects ----------------------------- LAPTOPS - Power Settings WSUS - Set Server Address OUTLOOK - Auto Archive SECURITY - Lock Screen After Idle Default Domain Policy DESKTOP - Regional Settings NETWORK - Proxy Configuration NETWORK - IE General Config OFFICE - Trusted Locations OFFICE - Increase Privacy OUTLOOK - Disable Junk Filter DESKTOP - Disable Windows Error Reporting DESKTOP - Hide Language Bar NETWORK - Disable Skype DESKTOP - Disable Thumbs.db Creation WSUS - Set Server Address The following GPOs were not applied because they were filtered out ------------------------------------------------------------------- Local Group Policy Filtering: Not Applied (Empty) NETWORK - Google Chrome Configuration Filtering: Not Applied (Empty) SYSTEM - Event Log Configuration Filtering: Not Applied (Empty) SECURITY - Local Administrator Password Filtering: Not Applied (Empty) NETWORK - Disable Windows Messenger Filtering: Not Applied (Empty) SECURITY - Audit Policy Filtering: Not Applied (Empty) WSUS - Automatic Install Filtering: Not Applied (Empty) NETWORK - Firewall Configuration Filtering: Not Applied (Empty) DESKTOP - Enable Offline Files Filtering: Not Applied (Empty) I haven't altered permissions on the GPO's at all, no WMI filtering... As I said, GP Modelling says that they should be applied. GPResult on the client correctly identifies itself as being the correct OU (CN=Amir,OU=Users,OU=NATO,DC=natorg,DC=local) There are 2 x 2008R2 and a 2003 DC, domain is 2003 level, client is Windows XP SP3. Can anyone suggest why these GP Objects would be "invisible" to the client?

  Read the article

• "Unable to initialize module" fileinfo php-pecl-Fileinfo.x86_64

  - by Myers Network

  I have a brand new server server that I am trying to get setup up. This is a 64 bit machine that I can not install "fileinfo" or "memcache". I have uninstalled these and reinstalled them using yum and pecl with no luck. Yum install fine "no error" but then get error when running php. pecl from what I can tell is only installing 32bit. Does not put anything in the lib64 directory. Here is my output from php -v: PHP Warning: PHP Startup: fileinfo: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 PHP Warning: PHP Startup: memcache: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 PHP 5.2.14 (cli) (built: Aug 12 2010 16:03:48) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.2.0, Copyright (c) 1998-2010 Zend Technologies Here is some other system info incase you need it uname: Linux server.actham.us 2.6.18-194.26.1.el5 #1 SMP Tue Nov 9 12:54:20 EST 2010 x86_64 x86_64 x86_64 GNU/Linux php -m: PHP Warning: PHP Startup: fileinfo: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 PHP Warning: PHP Startup: memcache: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 [PHP Modules] bz2 calendar ctype curl date dbase dom exif filter ftp gd gettext gmp hash iconv imap json ldap libxml mbstring mcrypt mysql mysqli openssl pcntl pcre PDO pdo_mysql pdo_sqlite readline Reflection session shmop SimpleXML sockets SPL standard tokenizer wddx xml xmlreader xmlrpc xmlwriter xsl zip zlib [Zend Modules] Any help would be greatly appreciated, thanks....

  Read the article

• Outlook 2007 "Mark as Not Junk" Dialog Confusion

  - by David

  Outlook 2007's "Not Junk" button opens the "Mark as Not Junk" dialog. The dialog works correctly if I keep the "Always trust e-mail from <email address>" option checked. That is, the message is removed from the Junk folder and returns to the Inbox. However, if I uncheck the "Always trust" box, pressing OK dismisses the dialog, but nothing else happens. Why not? According to Outlook help, "When you mark a message as not junk, you are given the option of adding the sender or the mailing list name to your Safe Senders List or Safe Recipients List." That sure makes it sound like this is just an option, and not necessary for the core functionality of the action. I really don't want to trust a (possibly forged) From: address, but I do want my mail back in the Inbox. I could manually drag it, but I'm assuming that marking a message as not junk also trains some kind of bayesian filter. Am I mistaken? Thanks.

  Read the article

• How to test email spam scores with amavis?

  - by CaptSaltyJack

  I'd like a way to test a spam message to see its spam scores that SpamAssassin gives it. The SA db files (bayes_toks, etc) reside in /var/lib/amavis/.spamassassin. I've been testing emails by doing this: sudo su amavis -c 'spamassassin -t msgfile' Though this yields some strange results, such as: Content analysis details: (3.7 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- 3.5 BAYES_99 BODY: Bayes spam probability is 99 to 100% [score: 1.0000] -0.0 NO_RELAYS Informational: message was not relayed via SMTP 0.0 LONG_TERM_PRICE BODY: LONG_TERM_PRICE 0.2 BAYES_999 BODY: Bayes spam probability is 99.9 to 100% [score: 1.0000] -0.0 NO_RECEIVED Informational: message has no Received headers 0.2 is an awfully low scores for BAYES_999! But this is the first time I've used amavis, previously I've always just used spamassassin directly as a content filter in postfix, but apparently running amavis/spamassassin is more efficient. So, with amavis in the picture, how can I run a test on a message to see its spam score breakdown? Another email I ran a test on got this result: 2.0 BAYES_80 BODY: Bayes spam probability is 80 to 95% [score: 0.8487] Doesn't make sense, that BAYES_80 can yield a higher score than BAYES_999. Help!

  Read the article

• LDAP not showing secondary groups

  - by Sandy Dolphinaura

  Currently, I have a LDAP server (running ClearOS if that makes any difference) containing a database of users. So, I went and setup LDAP on a couple of my debian VMs, using libpam-ldapd and I discovered this odd problem. My group/user mapping would show up when running getent group but the secondary groups would not show up when running id . Here is my /etc/nslcd.conf # /etc/nslcd.conf # nslcd configuration file. See nslcd.conf(5) # for details. # The user and group nslcd should run as. uid nslcd gid nslcd # The location at which the LDAP server(s) should be reachable. uri ldaps://10.3.0.1 # The search base that will be used for all queries. base dc=pnet,dc=sandyd,dc=me # The LDAP protocol version to use. #ldap_version 3 # The DN to bind with for normal lookups. binddn cn=manager,ou=internal,dc=pnet,dc=sandyd,dc=me bindpw Me29Dakyoz8Wn2zI # The DN used for password modifications by root. #rootpwmoddn cn=admin,dc=example,dc=com # SSL options ssl on tls_reqcert never # The search scope. #scope sub #filter group (&(objectClass=group)(gidNumber=*)) map group uniqueMember member

  Read the article

• Change XRDP keyboard layout to en-gb Ubuntu 12.04

  - by Earl Sven

  Does anybody know how to change the keyboard layout to en-gb in an XRDP session on Ubuntu 12.04? I am using mstsc.exe to connect to an XRDP server hosting an XVNC session, however I cannot work out how to apply the UK keyboard layout. A bit of googling has yeilded these instructions which allow me to change the keymap, however using the keymap file I downloaded from here I loose the ability to use the arrow keys, home/end etc. Comparing the file with the standard one there are substantially more differences than I would expect considering the similarity between the layouts. I only have RDP access to the box so i don't seem to be able to actually generate a new layout per the instructions above, maybe it's a local console thing? Also I can't change either the RDP client used or the RDP server as they are my only access to the system, I don't have local console access. I do have root priveleges on the OS however. Any thoughts? Edit: I have found http:// xrdp.sourceforge.net/documents/keymap/newkeymap.html (apologies for not typing the link properly but the antispam filter won't let me post more than 2 links) this documentation on the XRDP sourceforge page which describes keymap file format. It indicates the values in the keymap files are unicode 0x64 etc, however the files I have already on my system seem to use a different format 0:0 or 65307:27 etc, does anybody know what the difference is?

  Read the article

• Configure J2EE Agent with OpenAM behind Reverse Proxy

  - by Troy

  I have a reverse proxy with two SSL enabled NamedVirtualHosts on different ports. Both containers on each internal host is GF 2.1.1. Proxy configuration as follows: Proxy URL -> Internal URL https://apps.mydomain.com -> http://apps.internal.com https://secure.otherdomain.com:8080/ -> http://secure.internal.com I initially tried configuring the J2EE agent in OpenAM and the web app container to use the internal URLs (I appended /openam and /agentapp respectively). However, I received the following errors when trying to access a secured application such as https://apps.mydomain.com/webapp. java.lang.RuntimeException: Failed to load configuration: ApplicationSSOTokenProvider.getApplicationSSOToken(): Unable to get Application SSO Token A second attempt gives the following error: java.lang.NoClassDefFoundError: Could not initialize class com.sun.identity.agents.filter.AmFilterManager Along with these in the agent debug.out: ERROR: Failed to obtain auth service url from server: null://null:null ... SiteMonitor: Site URL http://secure.internal.com/openam/namingservice is not available. If I specify the server and agent urls using the proxy urls, then the agent appears to be working and I am redirected to the OpenAM login page. However, the goto in the URL is http://apps.mydomain.com/webapp instead of https://apps.mydomain.com/webapp (missing https). So after authentication, the redirect fails. Now I could possibly get by with mod_rewrite, but it feels hackish and I really want to know what's going on. Any ideas?

  Read the article

• How do I get a Mac to request a new IP address from another DHCP server running in parallel while Ne

  - by huyqt

  Hello, I have an interesting situation. I'm trying to us a Linux based machine to allow Mac's to Netboot (similiar to PXE boot) by running a DHCP service in parallel with the "global" DHCP server. The local DHCP server hands out IPs in a private subnet, e.g., 10.168.0.10-10.168.254-254, while the "global" DHCP server hands out IPs from the IP range 10.0.0.1 - 10.0.1.254. The local DHCP range is only supposed to be used in Preboot Execution Environment and Netboot. The local DHCP server is something I have control over, but I do not have access to the global DHCP server. I have a filter to only allow members with the vendor strings "AAPLBSDPC/i386" and "PXEClient". PXE works fine, but Netboot has a quirk. The Apple systems that haven't been connected to the network yet can Netboot fine. But once it grabs a "real" IP address from the global DHCP server, it will "save" it and request it the next time we want it to netboot (which the local dhcp server won't give it). This is what I want: Mar 30 10:52:28 dev01 dhcpd: DHCPDISCOVER from 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:29 dev01 dhcpd: DHCPOFFER on 10.168.222.46 to 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:31 dev01 dhcpd: DHCPREQUEST for 10.168.222.46 (10.168.0.1) from 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:31 dev01 dhcpd: DHCPACK on 10.168.222.46 to 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:32 dev01 in.tftpd[5890]: tftp: client does not accept options Mar 30 10:52:53 dev01 in.tftpd[5891]: tftp: client does not accept options Mar 30 10:52:53 dev01 in.tftpd[5893]: tftp: client does not accept options Mar 30 10:52:54 dev01 in.tftpd[5895]: tftp: client does not accept options This is what I get when it already has a "stored" IP: Mar 30 10:51:29 dev01 dhcpd: DHCPDISCOVER from 00:25:xx:xx:xx:xx via eth1 Mar 30 10:51:30 dev01 dhcpd: DHCPOFFER on 10.168.222.45 to 00:25:xx:xx:xx:xx via eth1 Mar 30 10:51:31 dev01 dhcpd: DHCPREQUEST for 10.0.0.61 (10.0.0.1) from 00:25:xx:xx:xx:xx via eth1: ignored (not authoritative). Do you have any suggestions? It would be much appreciated.

  Read the article

• Moving automatically spam messages to a folder in Postfix

  - by cad

  Hi My problem is that I want to automatically to move spam messages to a folder and not sure how. I have a linux box giving email access. MTA is Postfix, IMAP is Courier. As webmail client I use Squirrelmail. To filter SPAM I use Spamassassin and is working ok. Spamassasin is overwriting subjects with [--- SPAM 14.3 ---] Viagra... Also is adding headers: X-Spam-Flag: YES X-Spam-Checker-Version: SpamAssassin 3.2.5 (2008-06-10) on xxxx X-Spam-Level: ************** X-Spam-Status: Yes, score=14.3 required=2.0 tests=BAYES_99, DATE_IN_FUTURE_24_48,HTML_MESSAGE,MIME_HTML_ONLY,RCVD_IN_PBL, RCVD_IN_SORBS_WEB,RCVD_IN_XBL,RDNS_NONE,URIBL_RED,URIBL_SBL autolearn=no version=3.2.5 X-Spam-Report: * 0.0 URIBL_RED Contains an URL listed in the URIBL redlist * [URIs: myimg.de] * 3.5 BAYES_99 BODY: Bayesian spam probability is 99 to 100% * [score: 1.0000] * 0.9 RCVD_IN_PBL RBL: Received via a relay in Spamhaus PBL * [113.170.131.234 listed in zen.spamhaus.org] * 3.0 RCVD_IN_XBL RBL: Received via a relay in Spamhaus XBL * 0.6 RCVD_IN_SORBS_WEB RBL: SORBS: sender is a abuseable web server * [113.170.131.234 listed in dnsbl.sorbs.net] * 3.2 DATE_IN_FUTURE_24_48 Date: is 24 to 48 hours after Received: date * 0.0 HTML_MESSAGE BODY: HTML included in message * 1.5 MIME_HTML_ONLY BODY: Message only has text/html MIME parts * 1.5 URIBL_SBL Contains an URL listed in the SBL blocklist * [URIs: myimg.de] * 0.1 RDNS_NONE Delivered to trusted network by a host with no rDNS I want to automatically to move spam messages to a folder. Ideally (not sure if possible) only to move messages with puntuation 5.0 or more to folder.. spam between 2.0 and 5.0 I want to be stored in Inbox. (I plan later to switch autolearn on) After reading a lot in procmail, postfix and spamassasin sites and googling a lot (lot of outdated howtos) I found two solutions but not sure which is the best or if there is another one: Put a rule in squirrelmail (dirty solution?) Use Procmail Which is the best option? Do you have any updated howto about it? Thanks

  Read the article

• SQL Server Installaion error 0x84B40000

  - by Kurtevich

  I have a problem installing SQL Server 2008 R2. Long time ago I had it installed, and then uninstalled. It was left in "Add/remove programs", but I didn't pay attention on that. I had 2005 installed. And now there is a need to install 2008. I removed 2005 and started installing 2008, but it says that space on C: is not enough. That's when I found out that "Add/remove programs" shows it occupying more than 4 gigabytes, though I used to uninstall it. So I click "Remove", it shows all those many screens and validations, shows that removal completed, but the size of Program Files folder is still more than 4 GB. I removed (from "Add\remove programs" everything that had "SQL Server" in it's name, but that main "SQL Server 2008" item is still there and still 4 GB and uninstalling does nothing. Because installation of SQL Server did not show existing instances, and I don't see any running services related to SQL server (well, almost any, more details in the end), I though that this folder contains just some leftover staff and data and deleted it manually. Then agreed to removing of the item in "Add/remove programs" and everything looks clean. Now every time I try to install SQL Server (even in the minimum configuration), I receive the following error: SQL Server Setup has encountered the following error: The specified credentials that were provided for the SQL Server service are not valid. To continue, provide a valid account and password for the SQL Server service. Error code 0x84B40000. What is this service mentioned here? This error looks like I'm trying to add features to existing server and it can't login. But the setup didn't ask me for any credentials, except one username that couldn't be changed. Here are the services shown that can be related, both disabled and pointing to non-existing executables: SQL Active Directory Helper Service SQL Full-text Filter Daemon Launcher (MSSQLSERVER) I understand that this must be because of my manual deletion, but is there a way to clean it up now?

  Read the article

< Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >