Search Results

Search found 22877 results on 916 pages for 'network storage'.

Page 164/916 | < Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >

• Network tools not working with a 3G connection

  - by gAMBOOKa

  Some of my network tools stopped working after I switched to a 3G connection from a DSL one. Cain and Abel's sniffer, Metasploit, even the NMAP scanner. I'm using Windows 7. The 3G device in question is the Huawei E180. Here's the error I get when running NMAP WARNING: Using raw sockets because ppp2 is not an ethernet device. This probably won't work on Windows. pcap_open_live(ppp2, 100, 0, 2) FAILED. Reported error: Error opening adapter: The system cannot find the device specified. (20). Will wait 5 seconds then retry. pcap_open_live(ppp2, 100, 0, 2) FAILED. Reported error: Error opening adapter: The system cannot find the device specified. (20). Will wait 25 seconds then retry. Call to pcap_open_live(ppp2, 100, 0, 2) failed three times. Reported error: Error opening adapter: The system cannot find the device specified. (20) Metasploit's refused connection to my websites too.

  Read the article

• USB 3.0 hard disk not detected on a particular host controller?

  - by Alvin Wong

  I have a USB 3.0 hard disk which has always been working on my desktop with an XHCI. Now I just bought a notebook with an XHCI (something with Intel's Ivy Bridge setup). The first time I plug the hard disk in its 3.0 port it is detected and working. A few hours later I try to connect it again, but seems that the notebook just ignored it! The light on the hard disk didn't blink as usual (instead it is hold at on). I then tested it with my desktop again and it is working perfectly. It gets trickier when I plug it in the USB 2.0 port of that notebook it is detected and working perfectly (despite the slower speed). Then I try to plug in an USB 2.0 USB flash drive to that USB 3.0 port, and it is detected (of course as USB 2.0). So, there are two USB 3.0 ports on my notebook's XHCI. Both of them are not working with my hard disk but working perfectly fine with my USB 2.0 UFD. What's wrong with it? When I plug in the hard disk, device manager doesn't change. I've tried re-installing the driver for the XHCI, but it changes nothing. Had I broke the USB 3.0-specific pins of both USB 3.0 ports?

  Read the article

• Printing to shared printers across VPN

  - by CYMR0

  I have a program that prints labels at five remote sites. Two sites, aren't working, but the rest are with an identical (as far as I can tell) setup. Using Wireshark, I have determined that the handshaking all goes well, but after the "Open Print File Response" the packet that is sent from the server, doesn't reach the client. But I'm a bit at a loss as to where I go from here. I know the port the packet was sent on (445) isn't being blocked, the RST packet gets sent on the same port and that gets there fine. It's also weird that the three out of five sites are working fine. This has been up and running for years without issue, all that we have changed is our connectivity (from DSL to bonded DSL). But this traffic is over a VPN - so it can't be the ISP interfering either can it? I'm totally stuck, and any help would be much appreciated. Thanks!

  Read the article

• How to know which program is using the WebClient service?

  - by sork

  Hello, I just found out by using TCPView that one of my svchost.exe had an http connection in "CLOSE_WAIT" to a strange ip address, although no other visible program was running. With the help of Process Explorer I discovered that this svchost was using the WebClient windows service. I'm wondering how I can figure out what program used WebClient to connect to this ip, in order to determine if it's malware.

  Read the article

• Real benefits of tcp TIME-WAIT and implications in production environment

  - by user64204

  SOME THEORY I've been doing some reading on tcp TIME-WAIT (here and there) and what I read is that it's a value set to 2 x MSL (maximum segment life) which keeps a connection in the "connection table" for a while to guarantee that, "before your allowed to create a connection with the same tuple, all the packets belonging to previous incarnations of that tuple will be dead". Since segments received (apart from SYN under specific circumstances) while a connection is either in TIME-WAIT or no longer existing would be discarded, why not close the connection right away? Q1: Is it because there is less processing involved in dealing with segments from old connections and less processing to create a new connection on the same tuple when in TIME-WAIT (i.e. are there performance benefits)? If the above explanation doesn't stand, the only reason I see the TIME-WAIT being useful would be if a client sends a SYN for a connection before it sends remaining segments for an old connection on the same tuple in which case the receiver would re-open the connection but then get bad segments and and would have to terminate it. Q2: Is this analysis correct? Q3: Are there other benefits to using TIME-WAIT? SOME PRACTICE I've been looking at the munin graphs on a production server that I administrate. Here is one: As you can see there are more connections in TIME-WAIT than ESTABLISHED, around twice as many most of the time, on some occasions four times as many. Q4: Does this have an impact on performance? Q5: If so, is it wise/recommended to reduce the TIME-WAIT value (and what to)? Q6: Is this ratio of TIME-WAIT / ESTABLISHED connections normal? Could this be related to malicious connection attempts?

  Read the article

• Manage internet connection for a programm

  - by michel

  I'am using a Windows 7 pc with 2 networkcards one for public line and one for internal line behind proxy. is there a way or a software programm where i can manage wich programm(outlook, WM) use wich internet connection or networkcard use the option of interface metric is not where i was looking for. someone also suggest me Zonealarm. but i dislike this programm. thx

  Read the article

• Simulating an UNC path with a leading dot

  - by Uwe Keim

  Being a C# .NET Windows Forms developer, some customers are running our applications on an Apple OS X Mac inside a Parallels virtual machine. Parallels presents host folders to the guest Windows as UNC paths with a leading dot like \\.psf\Home\Some\More\Folders Now an application of us cannot handle the leading dot correctly when accessing files from these kind of shares ("Invalid URI, cannot analyze host name" exception). I want to debug and fix this issue, unfortunately I do have no Mac and Parallels around here to test it. My question is: Is there a way to "simulate" this kind of share on a normal Windows server or client so that I'll be able to debug my application with Visual Studio? What I tried so far: I already tried to edit my HOSTS file to contain an entry like # ... 127.0.0.1 .psf # ... but Windows just seems to not recognize the share at all.

  Read the article

• PolyCenter Netview & Console Manager

  - by Dave

  Hi, I'm looking to replace Polycenter Newview and Polycenter Console Manager with supported products. I'm starting with this list. Do you have any recommendations, either from that list or elsewhere?

  Read the article

• Windows IIS test server setup

  - by chopps

  hello everyone, I picked up a new server to do some testing and need of a little help in setting up my environment at home. Here is what I would like to do: The test server will be used to test new code and configurations for a SaaS product. I would like from my laptop to enter www.acme.com and have it hit the server. The server is connected to a wireless router. I have windows server 2008 with IIS running on an an IP of 192.168.1.4. What is the best way to set this up? I want to hit the test server for www.acme.com and not go out to the internet. Do i need to mess with the LMHosts file? Thanks for the help. Im sure its easy but have never done this before.

  Read the article

• How can I capture a process traffic?

  - by Yassin

  I would like to capture the traffic generated by a specific process (using Wireshark or other packet sniffer). Does anyone know how to do it? Thanks!

  Read the article

• Software to store frequently used text in PC

  - by user15660

  Hi, I am a looking for a free software that can run on the task bar (near the system time) where I can store frequently used text like my full street address, paths of specific deep folders & files in the computer etc etc. This way I can just click the icon which should popup a screen where I should be able to copy the text/string I am looking for Any ideas? thanks in advance

  Read the article

• Samba Public and "Dropbox" folder

  - by cb0

  I want to create a special Group Directory structure for my Users. /home/groupA <-- home folder for groupA where every user of groupA can create/edit/delete files /home/groupA/Public <-- Public Folder where every user can read files /home/groupA/Public/Dropbox <-- Folder where every user can write files but only users of groupA can access this directory and create/edit/delete files Now I have: 4 drwxrwx--t 10 nobody groupA 4096 Feb 18 15:44 /home/groupA 4 drwxrwxr-x 7 nobody groupA 4096 Feb 18 15:40 /home/groupA/Public/ 4 drwxrwx-w- 10 nobody groupA 4096 Feb 18 15:55 /home/groupA/Public/Dropbox My smc.confcontains the following entrys [groupA] path = /home/groupA comment = Folder for users of groupA browseable = yes read only = no create mask = 0770 directory mask = 0770 force group = groupA [groupA Public] path = /home/groupA/Public comment = Admins Public Browseable = yes write list = @groupA create mask = 0775 directory mask = 0775 [groupA DropBox] path = /home/groupA/Public/Dropbox comment = groupA Dropbox read only = no valid users = @groupA browseable = yes inherit owner = yes directory mode = 3770 force directory mode = 3770 The working part is: Users of groupA can access and fully use /home/groupA All Users can access /home/groupA/Public/ and read the files from there. My problem is that all users, even those who are not in groupA can access the /home/groupA/Public/Dropbox and see all files. I just want them to be able to put files in there but not see the content of the folder and prohibit them from deleting any files in there. Does anybody have a clue what could be the problem and how I can fix it ?

  Read the article

• Free Cloud Mind Map Solution

  - by Zekta Chan

  As a Software Engineer we had a lot of discussion on SE design. Although we sync every document on the development process on Google Doc, mind map just didn’t fit in Google doc yet. The best we can do is to store a copy and share it online. To me, Mind map is an ir-replaceable piece of tools (yet) as agile note taking tools. And an eFormat is even greater than a paper one, due to the portability and extensibility. Does anyone have a good solution on “cloud-sharing” mind map? (We are using FreeMind at the moment) Thanks

  Read the article

• Installing a Wl-138g wireless NIC on ubuntu server

  - by Narcolapser

  So I have this little server that I've been working on as a hobby. But due to changes in living arrangements I have move and it won't have access to a wired lan. So I need to install a wireless adapter i had sitting around. But most tutorials I have run across are either out dated, or about ubuntu desktop and talk about things using a GUI. So my question is firstly is there a utility for identifying and downloading drivers for new hardware. that would save my having this problem in the future. If not, how do i go about installing said wireless NIC? ~N

  Read the article

• Roughly cutting Fibre Cables

  - by Bryan

  I recently asked a question about which type of Fibre optic cable to use for my installation. We have now found a cable type and supplier and I'm about to order the cable (OM3, Tight Buffered, 12 Core), however I have a further question: We are shortly moving in to a new building (still being constructed) and we are about to get a window in which we will be able to run any cabling that we need. How should I roughly cut the fibre? Can I just use some heavy shears to cut through the cable? I'm aware that doing so will damage the ends, but will the damage be limited to the ends, or could the cracks/fractures continue up the length of the cable? p.s. I have already allowed for several metres of extra cable at each end, and I am going to get a specialist in to terminate the fibres.

  Read the article

• MicroSD card isn't detected by computer, apparently usable only with phone

  - by paulcjoubert

  I have a 4GB MicroSD card that apparently only works (in the sense that the device detects and can read and write from and to the card) with my old Nokia XpressMusic 5800 phone. I have taken pictures and recorded voice notes that were saved on the card. These are accessible after the card has been removed, which tells me that the problem isn't with the card. The card could also not be locked to the phone as it would at least be detected by a computer and it would be able to write raw data to it with dd, such as /dev/zero. Also, the card is not the Nokia card that came with the phone and I have done nothing that would have caused it to be locked. (I could not find anything on Nokia's website that helps, but then again... my search was not THAT thorough.) The card works on no other device that I have tried so far. I have tried it in my Canon camera (through an adapter), but it refuses to even boot with the card inserted. My card reader (via USB cable and hub) is detected as /dev/sdx with or without the card inserted. When trying to access the card I get an "No medium found". dmesg does not report any change at all when inserting and removing the card. I would obviously like to use my card on other devices - the phone is quite old - and even a likely explanation would help. Thankyou in advance! EDIT 1: I can use the card by connecting the phone to my computer, but this is impractical and would not allow me to use the card in any other device. EDIT 2: The data on the card is not important to me at all.

  Read the article

• Play system sounds from one computer through another computer's speakers?

  - by kevinconner

  I have a Mac and a Windows PC at work. I use both at the same time with Synergy and SynergyKM, which is a great setup for me. The Mac has built-in speakers and the PC has a sound card, but no speakers. I don't want to get speakers for use at work; instead I'd rather just have all sounds from both computers play through the Mac's speakers. Is there some sort of audio service I can run on each computer to accomplish that? I would want: System alert sounds, like you configure in the Control Panel Sounds from videos in a web browser, including from Flash

  Read the article

• Windows File Sharing - Long Initial Delay

  - by Isaac Sutherland

  I have two Windows 7 machines connected to a router. I created a shared folder on machine A, and I can access it from machine B. The transfer speed is great. However, there is sometimes a long initial delay when I try to access the shared folder from machine B. I'll click to open the folder, and windows explorer pauses for a few minutes before actually loading the contents of the folder. After it loads, however, I can navigate the subfolders and edit files with no noticeable delay. Then, some time later, I will get the huge delay on saving a file, after which subsequent saves have no delay. What is the problem here, and how can I fix it?

  Read the article

• Wireless to Wireless Transfer Slow on a Linksys WRT54GL

  - by Kyle Brandt

  The Situation: When I try to transfer a file from one computer to another that are both connected via wireless on a WRT54GL (in a office) with dd-wrt firmware I often get bad speeds. In generally they average around 100 kilobytes a second. Either computer can download via wireless from the Internet at at about 2 megabytes a second. The speed is slow with the transfer of one large file. There are about 20 other wireless networks that the computers can see, so there is a lot of noise, but I don't have the equipment to really monitor the frequencies well. But that still seems pretty slow. I thought maybe it was the transmit on each card, but even when they are 5 feet away with a line of sight I still get these speeds. According to Linux both cards are operating at 54g. My Questions: Is this normal for this sort of consumer level wireless equipment? Anything I can do to improve it? why is wireless to wireless transfer slow when everything else isn't? Whats steps might I take to figure out what is happening? For example, are lots of packets not making to the access point requiring retransmissions? Above all, I want to find out what the problem actually is. This may seem odd, but at this point I am more interested in understanding what the problem is than fixing it. What I have tried: I have tried messing with lots of settings. Different channels, xmit power, G-Only, none of which has made anything any better. I've also tried upgrading to newer dd-wrt firmware version and doing a reset to wipe out the settings.

  Read the article

• Mountain Lion fails to connect to Windows share after the connection is interrupted

  - by T Reddy

  I have a Windows 7 share that my Mountain Lion Macbook Pro connects to. The windows share is simply a user account. For whatever reason, when my connection gets interrupted, the mac will show a dialog stating as such and will ask me to ignore or disconnect. From this point forward, I cannot re-establish the connection from the mac to the windows share (even if I reboot the mac). I always have to reboot the windows machine in order for my mac to see the share again. My Windows share is my media center, so I'm not always able to reboot the machine because it is recording TV. Has anybody else encountered this problem and if so how is it resolved?

  Read the article

• Samba 'include' a per user config script

  - by cb0

  It is possible to use the include = /somepath/%u.smb.conf in the global section to call a script /somepath/cb0.smb.conf if the user cb0 connects to the samba server. Unfortunately this does not wotk for me because testparm alway gives me Can't find include file /somepath/.smb.conf When I connect to the server I can enter a username and pass but it alway rejects the connection. I'm using Samba Version 3.2.5 How can I achieve to load a custom user script depending on the user that is connecting ?

  Read the article

• Why would you use EAP-TTLS instead of PEAP?

  - by Ivan Macek

  As I understood EAP-TTLS and PEAP share same level of security when implemented in wireless networks. Both only provide server side authentication via certificate. The drawback of EAP-TTLS can be non native support in Microsoft Windows so every user has to install additional software. The benefit of EAP-TTLS can be support for less secure authentication mechanisms (PAP, CHAP, MS-CHAP) but why would you need them in modern and properly secure wireless system? What are you opinions? Why should I implement EAP-TTLS instead of PEAP? Let's say that I have most Windows users, medium Linux users and least iOS, OSX users.

  Read the article

• Getting an alert when my oracle database goes up or down

  - by CodeSlave

  How can I get an e-mail alert when my oracle database comes up or down? I have a database that I need to know when it goes down (it would be nice to know if it has come back up), preferably from a remote machine. Conceivably I could hack together something that TNSPings my DB and e-mails me when that changes, but I'm hoping there's a free package out there. Something that would run on windows. Any strong recommendations?

  Read the article

• finding the best network latency between two countries

  - by Yoav Aner

  I know there are many tools to test for bandwidth and latency, but they all rely on having at least one host from which you can run those tests. I wonder whether there's an online source or some other way to guestimate the latency or speed between two countries (in general). For example, would a customer in Japan get lower latency if the server is located in Singapore or Australia? Is a user in India likely to get higher download speed from a server in the UK or in the US? Are there any online resources or some clever ways to answer those questions with a reasonable degree of accuracy? [UPDATE]: Thanks for the great suggestions from Raffael Luthiger. I didn't know about those looking glass servers. The submarine cable maps were also really cool to discover (Thanks to Jesper Mortensen). Also seems really wise if I could ask those network professional in the area for their experience, but obviously I don't have access to those. At least some of them are on SF :) However, I'm still a little unsure how to combine those resources to give me some measurements. This is the information I have: Two countries (A,B). I do have IP addresses of customers in country A (I can obtain those from the web server log files for example). Presumably I can find some looking glass servers in country B and run a trace to those IPs. What's the best measurements to use? Are there any scripts that help automate at least some of this process?

  Read the article

• can't connect to vsftpd from outside network

  - by rick

  i know this has been asked many times before, but nothing seems to resolve my issue. i have vsftpd running on ubuntu 10.04. i can connect with ftp localhost on the machine. i can connect from another machine in my network. i just cannot connect from outside. the machine is behind an airport extreme managed by airport utility on a mac. 21 is open as per nmap: macmini:~$ nmap localhost Starting Nmap 5.21 ( http://nmap.org ) at 2011-04-10 23:49 EDT Nmap scan report for localhost (127.0.0.1) Host is up (0.00045s latency). Hostname localhost resolves to 2 IPs. Only scanned 127.0.0.1 rDNS record for 127.0.0.1: localhost.localdomain Not shown: 997 closed ports PORT STATE SERVICE 21/tcp open ftp 22/tcp open ssh 631/tcp open ipp netstat says 21 is listening: macmini:~$ netstat -lep --tcp | grep ftp (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.) tcp 0 0 *:ftp *:* LISTEN iptables: macmini:~$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination when i try to connect from my external IP (or a dyndns name which resolves there) it times out. ("control connection timed out") as i know very little about networking, i feel like something may jump out as clearly wrong?

  Read the article

< Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >