Search Results

Search found 6636 results on 266 pages for 'jdbc driver'.

Page 165/266 | < Previous Page | 161 162 163 164 165 166 167 168 169 170 171 172  | Next Page >

• Toshiba satellite L500 no Wifi anymore!

  - by Benjamin Piller

  I have a Toshiba Satellite L500 with Ubuntu 12.04 and its wifi suddenly stopped working!! I've never seen like that before.. I tried also using external USB wifis but no success. I am not able to turn it on with the function keys nor using rfkill commands and similar WLAN manipulator Commands in the terminal! It was working before for at least 4-5 months!! The computer says it's turned off by hardware. I checked it and the Driver is fine. So why can i not use any Wifi on my computer?? Why it is suddenly disabled? I checked the BIOS too there is enabled the WLAN. I spent 10 hours for searching for solutions but i am out of ideas!!! Please Help!

  Read the article

• No internet access since 12.04

  - by Roelof

  I have updated yesterday to Ubuntu 12.04 but can not access the Internet. It is an old PC without wireless. But the older Ubuntu I had installed up until now (11.??) worked perfectly. I'm not that familiar with Ubuntu, and I have been trying Google for some time know, but I cannot find the answer. I noticed that running nm-tool resulted in some things that don't sound right: Type: wired Driver: ne2k-pci state: unavailable Default: no Carrier: off Does anyone have a way to fix the connection?

  Read the article

• ati graphics always on

  - by naveen

  i use a lenovo y560 and has ubunto 12.04 and win 7 installed when i boot into ubunto i find that the ati car is always on which drains the battery and overheats the system is there any to switch off the ati graphics and use intel hd in ubuntu ati hd 5730 is the graphics card that i use and it has switchable graphics in it. in bios the only two options for video adapter is discrete and switchable after installing ati driver from amd website i am getting a commamd prompt as log in screen first error message comes as Your system is running in low-graphics mode with options to run in low graphics mode this time reconfigure exit all three options i am stuck i need to manually reboot the system

  Read the article

• Use hotplug and turn on/off PCI device for replacing NIC

  - by Ryota Hashimoto

  How can I turn off the PCI slots and change the device (especially NIC) without shutting the server down? I found a similar question (How do I turn off PCI devices?) but there are no /sys/bus/pci/slot and no files in /sys/bus/pci/slots. I'm using 12.04 LTS. $ uname -a Linux d1-c1-r1-p1 3.2.0-38-generic #61-Ubuntu SMP Tue Feb 19 12:18:21 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux $ lspci | grep Eth 04:00.0 Ethernet controller: Intel Corporation I350 Gigabit Network Connection (rev 01) 04:00.1 Ethernet controller: Intel Corporation I350 Gigabit Network Connection (rev 01) 09:00.0 Ethernet controller: Intel Corporation 82599EB 10-Gigabit SFI/SFP+ Network Connection (rev 01) 09:00.1 Ethernet controller: Intel Corporation 82599EB 10-Gigabit SFI/SFP+ Network Connection (rev 01) $ ls /sys/bus/pci/ devices/ drivers_probe slots/ drivers/ rescan uevent drivers_autoprobe resource_alignment $ ls /sys/bus/pci/devices/0000\:04\:00.0/ broken_parity_status driver modalias rescan subsystem class enable msi_bus reset subsystem_device config firmware_node net resource subsystem_vendor consistent_dma_mask_bits irq numa_node resource0 uevent device local_cpulist power resource2 vendor dma_mask_bits local_cpus remove resource3

  Read the article

• How should I handle using two databases with a legacy PHP application?

  - by Toby Allen

  I have a legacy PHP application that was written in 2004 and uses MSSQL as a database backend. At this stage MSSQL is still supported by PHP but only just via a Microsoft driver. I have looked at converting to mysql via automated tools, which work quite well, but I have quite complex views which need a lot of individual work to convert. I don't have a great deal of time to do this. Many tools I wish to use and frameworks I would like to move the application to, don't support MSSQL, so I was considering adding new features using a new mysql database and wondered if anyone had opinions on the pros and cons of using two seperate database backends in a single application?

  Read the article

• How to completely shutdown Ati card

  - by Celso

  I would like to know how do i prevent my Ati card from turning on when i enter on ubuntu 11.10. My bios only lets-me shutdown intel hd card or leave the both on but i want to know if is possbible to completely shutdown without having to access to the bios.( if is possible to turn of without using Vgaswitcheroo even better!) My system is: Acer 3820tg-- intel core i3 350M, 2.26 Ghz L3, Ati Mobility Radeon HD 5470 up to 2138 MB hyper memory, 13,3" HD LED LCD, 4gb DDR3, SSD corsair 60GB sata 2. EDIT: I now know what is missing on the answers! I edited /etc/rc.local file and added the next lines: Sleep 3 echo ON /sys/kernel/debug/vgaswitcheroo/switch echo IGD /sys/kernel/debug/vgaswitcheroo/switch echo OFF /sys/kernel/debug/vgaswitcheroo/switch And then save the file and restart. It should be possible to use only the intel card now. By the way, i didn't blacklisted the radeon driver because doing it make my ati card wake up. (use it at your own risk. i only tested in my system)

  Read the article

• Ubuntu 13.10 install VMware 9.0

  - by user212290

  After I install the VMware workstation 9.0, while when I want open the VM, there come the dialogue "Before you can run VMware, several modules must be complied and loaded into the running kernel CANCEL INSTALL",while I clicked the INSTALL button, nothing happened. When: sudo apt-get install linux-headers-3.11.0-12-generic sudo /usr/bin/vmware-modconfig --icon=vmware-workstation --appname=VMware come: cc1: some warnings being treated as errors make[2]: *** [/tmp/modconfig-T9k19t/vmci-only/linux/driver.o] Error 1 make[2]: *** Waiting for unfinished jobs.... make[1]: *** [_module_/tmp/modconfig-T9k19t/vmci-only] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.11.0-12-generic' make: *** [vmci.ko] Error 2 make: Leaving directory `/tmp/modconfig-T9k19t/vmci-only' Failed to build vmci. Failed to execute the build command. Starting VMware services: Virtual machine monitor done Virtual machine communication interface failed VM communication interface socket family done Blocking file system done Virtual ethernet failed VMware Authentication Daemon done

  Read the article

• Ubuntu 12.04 Touchscreen Calibration

  - by Lee

  I have a machine with Ubuntu 12.04 installed, with dual monitor, via VGA and DVI Interface. The monitor is one touch screen and the other one is regular LCD Monitor. The touch screen is made in China with some unknown brand, and I am using eGalax Driver. The touch screen is now detected and works, but i need to do some calibration since it does not correctly perform click on touch. The problem is, when I’m using xinput_calibrator, it shows 4 crosses to be clicked on, because I’m using dual monitor, the crosses is now show 2 on the touch screen (touchable) and the others on the other monitor which is regular non-touch monitor. Please help, thank you.

  Read the article

• Stuck on busybox after a fresh install

  - by user54841

  I installed 11.10 and was getting stuck on Busybox unless I type exit. After grabbing the latest updates it then didn't get stuck on busybox but instead on a black screen of nothingness. I've now reformatted and started again using the exit technique for the time being. I had a search here before posting and none of the answers gave much insight, other than it 'could be a gfx card driver issue'. I'm using new hardware that has no issues with Mint, Win7 or WinXp. BUT note, I'm not dual booting, its a complete fresh install formatting the entire drive. Any help is appreciated as I'd really like to get stuck into Ubuntu. Thanks in advance. -Luke

  Read the article

• Installing drivers for an ATI 6950 in Ubuntu

  - by aj.esler

  Is there any way to get ubuntu to recognise an ATI 6950? I have tried installing the proprietary ATI drivers, but these do not seem to work properly. It seems to screw up the gnome desktop, and starts booting into terminal. I'm somewhat of a linux newbie, so not really sure whats going wrong. I don't want to game on ubuntu, I just want it to recognise my dual monitor setup rather than mirroring the monitors, so any driver that does this is fine by me. It seems like the open source ATI radeon drivers will not support the 6950/6970 for some time, at least until kernel 2.6.38 is released. The card is also flashed with the 6970 firmware, not sure if this is important. I am running a 64 bit version of ubuntu, I installed ubuntu server 10.10, then installed gnome-desktop.

  Read the article

• Split screen and other issues on Ubuntu 11.10 with ATI graphics card

  - by garus

  Ever since updating my Ubuntu 11.04 to 11.10 I experience issues with graphics. The biggest is the "split screen" effect where my desktop is shifted to the right, resulting in having Unity bar in the middle of the screen. As shown here: http://i.imgur.com/I8nmZ.jpg This changes from boot to boot, sometimes it's on the left, sometimes in the middle. What I tried: Removing fglrx drivers completely Installing post-update version of them, but installation is broken ATM in the Ubuntu, so no go. No one is even trying to fix it (bug report https://bugs.launchpad.net/ubuntu/+source/nvidia-common/+bug/873058 and a couple of duplicates out there) Also using the open source "radeon" driver results in the same (I have a better successful boot ratio with this one, proprietary rarely lets me boot) Other artifacts are: serious screen tearing weird lines flickering in random places lagginess Did anyone experience that? My specs: Ubuntu 11.10 AMD Radeon HD 6950 1GB

  Read the article

• No HDMI sound output on Thinkpad X1

  - by nickf

  I'm having problems getting my sound to output via HDMI to my TV. When I go to Sound Settings, the HDMI device does not appear. ~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: CONEXANT Analog [CONEXANT Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 7: HDMI 1 [HDMI 1] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 8: HDMI 2 [HDMI 2] Subdevices: 1/1 Subdevice #0: subdevice #0 I don't know if the video information is helpful, but anyway: ~$ sudo lshw -C video *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:d0000000-d03fffff memory:c0000000-cfffffff ioport:5000(size=64) Any suggestions for me?

  Read the article

• Installing drivers for an ATI 6950

  - by aj.esler

  Is there any way to get ubuntu to recognise an ATI 6950? I have tried installing the proprietary ATI drivers, but these do not seem to work properly. It seems to screw up the gnome desktop, and starts booting into terminal. I'm somewhat of a linux newbie, so not really sure whats going wrong. I don't want to game on ubuntu, I just want it to recognise my dual monitor setup rather than mirroring the monitors, so any driver that does this is fine by me. It seems like the open source ATI radeon drivers will not support the 6950/6970 for some time, at least until kernel 2.6.38 is released. The card is also flashed with the 6970 firmware, not sure if this is important. I am running a 64 bit version of ubuntu, I installed ubuntu server 10.10, then installed gnome-desktop.

  Read the article

• Compiz runs almost at 100% and the system is slow, what can I do?

  - by Heiner Valverde

  My system became very slow out of the sudden, yesterday Compiz was running extremely smooth, today it started working very slow and slowing the computer. What I've done so far was to resize my swap partition to 6 gigabytes (my computer has 3 gigabytes of RAM), before it was on 5.1 gigabytes, so I though that was the reason of this but still not. Also I tested running only metacity by running metacity --replace and also with Mutter. With metacity works really great no problem but, in the other hand, with mutter the computer works slower than running compiz instead. I am using the Nvidia driver version 173.14.28 and my X Server version as reports the NVidia X Server Settings is the 11.0. My Linux kernel running on this computer is 2.6.35-25-generic and my ubuntu version is 10.10. Any help will be appreciated.

  Read the article

• Cannot login via Unity login screen after upgrade to 12.04

  - by codesurgeon

  Logging in via the shell accessed through Ctrl+Alt-F1 and logging in as guest via the graphical user interface work 0O When I try to log into my standard user account via the graphical interface, the screen flashes to black for a couple of seconds and bumps me back to a pristine login screen. Entering a wrong password for my user account yields the standard error message - my user account and credential verification seem to be OK. I suppose that my individual graphics configuration causes problems ... I'm not sure how to reset that. I've tried stopping the UI via sudo service lightdm stop executed sudo nvidia-xconfig and restarted the UI sudo service lightdm start to no avail. My workstation has a Nvidia GeForce 560-448 graphics card. I've tried getting this fixed with the latest Nvidia 64-bit drivers (cURL'ed from the official website), that is 295.49 and the latest beta driver 302.07. Anybody have an idea how to get this fixed? Your help is appreciated :)

  Read the article

• How do I handle "Firmware file X not found" stopping bootup?

  - by John Baber

  I recently upgraded my desktop mac to Precise and now can't get past the Ubuntu 12.04 splash page. The splash freezes with [ 19.931097] b32-phy0 ERROR: Firmware file "b43/ucode16_mimo.fw" not found [ 19.9311126] b32-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website. written on it This is when I choose 3.2.0-generic from the grub menu. If I choose to load up older kernels, I still get the same thing. How can I make my computer finish booting again? I'm able to ssh into the machine and poke around, but the actual screen freezes at the splash.

  Read the article

• Can't activate "mirror display"

  - by Nemo Peeters

  I have Ubuntu 12.04 on a Dell latitude E6410, I have a problem when using the VGA output I always have dual monitor and can't switch on the "mirror display" toggle under systems setting/displays. It's rather annoying when having to do presentation with a video projector. the option "mirror display" is in light grey and I can"t tick the box. Thanks for those who might have an idea how to resolve this? update: driver is: Intel® Ironlake Mobile x86/MMX/SSE2 card something like this ? description: VGA compatible controller product: Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 02 width: 64 bits clock: 33MHz

  Read the article

• No GUI, No internet connection, please help 12.04

  - by KB_

  I am new to Ubuntu and I tried to install ubuntu server 12.04 on my laptop. now my problem is - I am unable to connect to the internet (I have wifi ONLY connection). ubuntu didn't recognize my built-in wifi on my Toshiba Satellite L505. There is no GUI. I have Terminal only, I tried Sudo apt-get update but i am getting errer msg because of no connection. 1. I need to know if there is any possible way that i can download and install driver for my wifi. 2. what other option do i have to be able to update ubuntu. Thanks KB

  Read the article

• What is the situation about OpenGL under Ubuntu Unity and Gnome3?

  - by user827992

  In a GNU/linux distribution is usually installed Xorg as main graphical server, it operates with a client-server logic, a special windows is designate as desktop environment and this special windows can handle all the eyecandy stuff like decorations, icons and effects. The problem is that the latest UI heavily relies on hardware acceleration, Unity is an overlay on Compiz and the Gnome-shell also require an active driver for the GPU to work well: the problem is: on the same OS I can find multiple implementations of OpenGL who is handling my OpenGL buffer? how the OpenGL buffer is managed compared to the other windows? how can I be sure that my OpenGL implementation is glued to the hardware and is not related to the client-server logic of Xorg? For example I have tried the clutter library and I have only experienced problems under both Unity and GTK/Gnome, no problem under other OS.

  Read the article

• Laptop works fine with ac adapter, hangs after login screen using battery

  - by tavoton

  I did an Ubuntu 10.10 Desktop Edition clean install (amd64 version) on a notebook Medion Akoya E1311. With AC adapter everything works fine, but using battery, it hangs after login screen. I can type login, password too, and I can press login button. But then I can see mouse cursor and lower task bar, not upper, and nothing works. The only thing I can do is login on a terminal with ctrl+alt+F1, this is ok. Nothing seems alive on Gnome except mouse cursor. The only thing I did after Ubuntu fresh install was donwloading driver for RTL8191SE from Realtek web, because WiFi didn't work, now works fine, with ac adapter of course. Hardware is a Notebook Medion Akoya E1311 AMD Sempron 210U 1 GB DDR2 ATI RS690M (Radeon X1200 Series) Western Digital 160GB wireless RTL8191SEvB ethernet RTL8101E/RTL8102E

  Read the article

• Question about JPanel "transition" for Java Swing

  - by user16778

  I want to make like a sort of main menu (in GUI). When the user clicks the start button, the screen transition into another "screen" (JPanel). This image will make it easier to understand. http://i.imgur.com/Cfdry.png Currently, I have a MainMenu extends JPanel and that gets added into a driver class with a JFrame. I can't figure how to switch to another class like Game extends JPanel. So when the user clicks the start button in MainMenu, I want it to somehow hide itself and the Game to show itself. Thanks.

  Read the article

• How to perform a detailed and quick 3D performance test

  - by gsedej

  I am wondering how to quickly test performance of my 3D graphics. Since glxgears is not benchmark what should I use. Also glxgears sometimes stuck at 60FPS, you cannot even compare before/after driver update (e.g. adding xorg-edgers PPA). Even glxgears doesn't really work out of box. One possibility is screensavers, but you can't see FPS. I am also not willing to install 600MB nexuiz, specially if I am running on Live-CD. Other 3D games are also very big... Unigine tests are too demanding for opensource drivers (problems with too low OpenGL and probably texture compression (S3TC...)). I would also like to test OpenGL 2.x extentions. How to quickly test your 3D performance?

  Read the article

• Getting front audio jacks to work

  - by Ashfame

  I run Ubuntu 10.10 on my Intel D945. My front audio ports don't work in Ubuntu, the rear one does. I never got it working earlier when I had Ubuntu 10.04 but this time I am going to try it again. My codec is SigmaTel STAC9227 My ALSA information is here. Handy details: !!ALSA Version !!------------ Driver version: 1.0.23 Library version: 1.0.23 Utilities version: 1.0.23 !!Loaded ALSA modules !!------------------- snd_hda_intel snd_hda_intel I know something that I will have to change the model of my module to make the front audio jack works but I couldn't find a model related line in my ALSA configuration file - /etc/modprobe.d/alsa-base.conf (I was able to get to that point in Ubuntu 10.04, may be something has changed). How can I proceed from here?

  Read the article

• Management Software in Java for Networked Bus Systems

  - by Geertjan

  Telemotive AG develops complex networked bus systems such as Ethernet, MOST, CAN, FlexRay, LIN and Bluetooth as well as in-house product developments in infotainment, entertainment, and telematics related to driver assistance, connectivity, diagnosis, and e-mobility. Devices such as those developed by Telemotive typically come with management software, so that the device can be configured. (Just like an internet router comes with management software too.) The blue AdmiraL is a development and analysis device for the APIX (Automotive Pixel Link) technology. Here is its management tool: The blue PiraT is an optimised multi-data logger, developed by Telemotive specifically for the automotive industry. With the blue PiraT the communication of bus systems and control units are monitored and relevant data can be recorded very precisely. And here is how the tool is managed: Both applications are created in Java and, as clearly indicated in many ways in the screenshots above, are based on the NetBeans Platform. More details can be found on the Telemotive site.

  Read the article

• How do i stop or turn off the x-server?

  - by Alex

  im trying to do this tutorial: http://wiki.accelereyes.com/wiki/index.php/Installing_CUDA_Under_Ubuntu_10.04 I need the command that would completely stop/turn off the x-server. when i try to install the nvidia developer driver, i get a blue screen telling my Error:cant install with x-server running, please turn it off (something like that). "sudo service gdm stop" worked at the time i guess, (didnt give any errors) but the x-server is still running. is this the command i should be using? thanks for anyhelp!

  Read the article

< Previous Page | 161 162 163 164 165 166 167 168 169 170 171 172  | Next Page >