Search Results

Search found 4229 results on 170 pages for 'intel pentium'.

Page 166/170 | < Previous Page | 162 163 164 165 166 167 168 169 170  | Next Page >

• Improved Performance on PeopleSoft Combined Benchmark using SPARC T4-4

  - by Brian

  Oracle's SPARC T4-4 server running Oracle's PeopleSoft HCM 9.1 combined online and batch benchmark achieved a world record 18,000 concurrent users experiencing subsecond response time while executing a PeopleSoft Payroll batch job of 500,000 employees in 32.4 minutes. This result was obtained with a SPARC T4-4 server running Oracle Database 11g Release 2, a SPARC T4-4 server running PeopleSoft HCM 9.1 application server and a SPARC T4-2 server running Oracle WebLogic Server in the web tier. The SPARC T4-4 server running the application tier used Oracle Solaris Zones which provide a flexible, scalable and manageable virtualization environment. The average CPU utilization on the SPARC T4-2 server in the web tier was 17%, on the SPARC T4-4 server in the application tier it was 59%, and on the SPARC T4-4 server in the database tier was 47% (online and batch) leaving significant headroom for additional processing across the three tiers. The SPARC T4-4 server used for the database tier hosted Oracle Database 11g Release 2 using Oracle Automatic Storage Management (ASM) for database files management with I/O performance equivalent to raw devices. Performance Landscape Results are presented for the PeopleSoft HRMS Self-Service and Payroll combined benchmark. The new result with 128 streams shows significant improvement in the payroll batch processing time with little impact on the self-service component response time. PeopleSoft HRMS Self-Service and Payroll Benchmark Systems Users Ave Response Search (sec) Ave Response Save (sec) Batch Time (min) Streams SPARC T4-2 (web) SPARC T4-4 (app) SPARC T4-4 (db) 18,000 0.988 0.539 32.4 128 SPARC T4-2 (web) SPARC T4-4 (app) SPARC T4-4 (db) 18,000 0.944 0.503 43.3 64 The following results are for the PeopleSoft HRMS Self-Service benchmark that was previous run. The results are not directly comparable with the combined results because they do not include the payroll component. PeopleSoft HRMS Self-Service 9.1 Benchmark Systems Users Ave Response Search (sec) Ave Response Save (sec) Batch Time (min) Streams SPARC T4-2 (web) SPARC T4-4 (app) 2x SPARC T4-2 (db) 18,000 1.048 0.742 N/A N/A The following results are for the PeopleSoft Payroll benchmark that was previous run. The results are not directly comparable with the combined results because they do not include the self-service component. PeopleSoft Payroll (N.A.) 9.1 - 500K Employees (7 Million SQL PayCalc, Unicode) Systems Users Ave Response Search (sec) Ave Response Save (sec) Batch Time (min) Streams SPARC T4-4 (db) N/A N/A N/A 30.84 96 Configuration Summary Application Configuration: 1 x SPARC T4-4 server with 4 x SPARC T4 processors, 3.0 GHz 512 GB memory Oracle Solaris 11 11/11 PeopleTools 8.52 PeopleSoft HCM 9.1 Oracle Tuxedo, Version 10.3.0.0, 64-bit, Patch Level 031 Java Platform, Standard Edition Development Kit 6 Update 32 Database Configuration: 1 x SPARC T4-4 server with 4 x SPARC T4 processors, 3.0 GHz 256 GB memory Oracle Solaris 11 11/11 Oracle Database 11g Release 2 PeopleTools 8.52 Oracle Tuxedo, Version 10.3.0.0, 64-bit, Patch Level 031 Micro Focus Server Express (COBOL v 5.1.00) Web Tier Configuration: 1 x SPARC T4-2 server with 2 x SPARC T4 processors, 2.85 GHz 256 GB memory Oracle Solaris 11 11/11 PeopleTools 8.52 Oracle WebLogic Server 10.3.4 Java Platform, Standard Edition Development Kit 6 Update 32 Storage Configuration: 1 x Sun Server X2-4 as a COMSTAR head for data 4 x Intel Xeon X7550, 2.0 GHz 128 GB memory 1 x Sun Storage F5100 Flash Array (80 flash modules) 1 x Sun Storage F5100 Flash Array (40 flash modules) 1 x Sun Fire X4275 as a COMSTAR head for redo logs 12 x 2 TB SAS disks with Niwot Raid controller Benchmark Description This benchmark combines PeopleSoft HCM 9.1 HR Self Service online and PeopleSoft Payroll batch workloads to run on a unified database deployed on Oracle Database 11g Release 2. The PeopleSoft HRSS benchmark kit is a Oracle standard benchmark kit run by all platform vendors to measure the performance. It's an OLTP benchmark where DB SQLs are moderately complex. The results are certified by Oracle and a white paper is published. PeopleSoft HR SS defines a business transaction as a series of HTML pages that guide a user through a particular scenario. Users are defined as corporate Employees, Managers and HR administrators. The benchmark consist of 14 scenarios which emulate users performing typical HCM transactions such as viewing paycheck, promoting and hiring employees, updating employee profile and other typical HCM application transactions. All these transactions are well-defined in the PeopleSoft HR Self-Service 9.1 benchmark kit. This benchmark metric is the weighted average response search/save time for all the transactions. The PeopleSoft 9.1 Payroll (North America) benchmark demonstrates system performance for a range of processing volumes in a specific configuration. This workload represents large batch runs typical of a ERP environment during a mass update. The benchmark measures five application business process run times for a database representing large organization. They are Paysheet Creation, Payroll Calculation, Payroll Confirmation, Print Advice forms, and Create Direct Deposit File. The benchmark metric is the cumulative elapsed time taken to complete the Paysheet Creation, Payroll Calculation and Payroll Confirmation business application processes. The benchmark metrics are taken for each respective benchmark while running simultaneously on the same database back-end. Specifically, the payroll batch processes are started when the online workload reaches steady state (the maximum number of online users) and overlap with online transactions for the duration of the steady state. Key Points and Best Practices Two PeopleSoft Domain sets with 200 application servers each on a SPARC T4-4 server were hosted in 2 separate Oracle Solaris Zones to demonstrate consolidation of multiple application servers, ease of administration and performance tuning. Each Oracle Solaris Zone was bound to a separate processor set, each containing 15 cores (total 120 threads). The default set (1 core from first and third processor socket, total 16 threads) was used for network and disk interrupt handling. This was done to improve performance by reducing memory access latency by using the physical memory closest to the processors and offload I/O interrupt handling to default set threads, freeing up cpu resources for Application Servers threads and balancing application workload across 240 threads. A total of 128 PeopleSoft streams server processes where used on the database node to complete payroll batch job of 500,000 employees in 32.4 minutes. See Also Oracle PeopleSoft Benchmark White Papers oracle.com SPARC T4-2 Server oracle.com OTN SPARC T4-4 Server oracle.com OTN PeopleSoft Enterprise Human Capital Managementoracle.com OTN PeopleSoft Enterprise Human Capital Management (Payroll) oracle.com OTN Oracle Solaris oracle.com OTN Oracle Database 11g Release 2 oracle.com OTN Disclosure Statement Copyright 2012, Oracle and/or its affiliates. All rights reserved. Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners. Results as of 8 November 2012.

  Read the article

• Why We Should Learn to Stop Worrying and Love Millennials

  - by HCM-Oracle

  By Christine Mellon Much is said and written about the new generations of employees entering our workforce, as though they are a strange specimen, a mysterious life form to be “figured out,” accommodated and engaged – at a safe distance, of course.  At its worst, this talk takes a critical and disapproving tone, with baby boomer employees adamantly refusing to validate this new breed of worker, let alone determine how to help them succeed and achieve their potential.   The irony of our baby-boomer resentments and suspicions is that they belie the fact that we created the very vision that younger employees are striving to achieve.  From our frustrations with empty careers that did not fulfill us, from our opposition to “the man,” from our sharp memories of our parents’ toiling for 30 years just for the right to retire, from the simple desire not to live our lives in a state of invisibility, came the seeds of hope for something better. One characteristic of Millennial workers that grew from these seeds is the desire to experience as much as possible.  They are the “Experiential Employee”, with a passion for growing in diverse ways and expanding personal and professional horizons.  Rather than rooting themselves in a single company for a career, or even in a single career path, these employees are committed to building a broad portfolio of experiences and capabilities that will enable them to make a difference and to leave a mark of significance in the world.  How much richer is the organization that nurtures and leverages this inclination?  Our curmudgeonly ways must be surrendered and our focus redirected toward building the next generation of talent ecosystems, if we are to optimize what future generations have to offer.   Accelerating Professional Development In spite of our Boomer grumblings about Millennials’ “unrealistic” expectations, the truth is that we have a well-matched set of circumstances.  We have executives-in-waiting who want to learn quickly and a concurrent, urgent need to ramp up their development time, based on anticipated high levels of retirement in the next 10+ years.  Since we need to rapidly skill up these heirs to the corporate kingdom, isn’t it a fortunate coincidence that they are hungry to learn, develop and move fluidly throughout our organizations??  So our challenge now is to efficiently operationalize the wisdom we have acquired about effective learning and development.   We have already evolved from classroom-based models to diverse instructional methods.  The next step is to find the best approaches to help younger employees learn quickly and apply new learnings in an impactful way.   Creating temporary or even permanent functional partnerships among Millennial employees is one way to maximize outcomes.  This might take the form of 2 or more employees owning aspects of what once fell under a single role.  While one might argue this would mean duplication of resources, it could be a short term cost while employees come up to speed.  And the potential benefits would be numerous:  leveraging and validating the inherent sense of community of new generations, creating cross-functional skills with broad applicability, yielding additional perspectives and approaches to traditional work outcomes, and accelerating the performance curve for incumbents through Cooperative Learning (Johnson, D. and Johnson R., 1989, 1999).  This well-researched teaching strategy, where students support each other in the absorption and application of new information, has been shown to deliver faster, more efficient learning, and greater retention. Alternately, perhaps short term contracts with exiting retirees, or former retirees, to help facilitate the development of following generations may have merit.  Again, a short term cost, certainly.  However, the gains realized in shortening the learning curve, and strengthening engagement are substantial and lasting. Ultimately, there needs to be creative thinking applied for each organization on how to accelerate the capabilities of our future leaders in unique ways that mesh with current culture. The manner in which performance is evaluated must finally shift as well.  Employees will need to be assessed on how well they have developed key skills and capabilities vs. end-to-end mastery of functional positions they have no interest in keeping for an entire career. As we become more comfortable in placing greater and greater weight on competencies vs. tasks, we will realize increased organizational agility via this new generation of workers, which will be further enhanced by their natural flexibility and appetite for change. Revisiting Succession  For many years, organizations have failed to deliver desired succession planning outcomes.  According to CEB’s 2013 research, only 28% of current leaders were pre-identified in a succession plan. These disappointing results, along with the entrance of the experiential, Millennial employee into the workforce, may just provide the needed impetus for HR to reinvent succession processes.   We have recognized that the best professional development efforts are not always linear, and the time has come to fully adopt this philosophy in regard to succession as well.  Paths to specific organizational roles will not look the same for newer generations who seek out unique learning opportunities, without consideration of a singular career destination.  Rather than charting particular jobs as precursors for key positions, the experiences and skills behind what makes an incumbent successful must become essential in succession mapping.  And the multitude of ways in which those experiences and skills may be acquired must be factored into the process, along with the individual employee’s level of learning agility. While this may seem daunting, it is necessary and long overdue.  We have talked about the criticality of competency-based succession, however, we have not lived up to our own rhetoric.  Many Boomers have experienced the same frustration in our careers; knowing we are capable of shining in a particular role, but being denied the opportunity due to how our career history lined up, on paper, with documented job requirements.  These requirements usually emphasized past jobs/titles and specific tasks, versus capabilities, drive and willingness (let alone determination) to learn new things.  How satisfying would it be for us to leave a legacy where such narrow thinking no longer applies and potential is amplified? Realizing Diversity Another bloom from the seeds we Boomers have tried to plant over the past decades is a completely evolved view of diversity.  Millennial employees assume a diverse workforce, and are startled by anything less.  Their social tolerance, nurtured by wide and diverse networks, is unprecedented.  College graduates expect a similar landscape in the “real world” to what they experienced throughout their lives.  They appreciate and seek out divergent points of view and experiences without needing any persuasion.  The face of our U.S. workforce will likely see dramatic change as Millennials apply their fresh take on hiring and building strong teams, with an inherent sense of inclusion.  This wonderful aspect of the Millennial wave should be celebrated and strongly encouraged, as it is the fulfillment of our own aspirations. Future Perfect The Experiential Employee is operating more as a free agent than a long term player, and their commitment will essentially last as long as meaningful organizational culture and personal/professional opportunities keep their interest.  As Boomers, we have laid the foundation for this new, spirited employment attitude, and we should take pride in knowing that.  Generations to come will challenge organizations to excel in how they identify, manage and nurture talent. Let’s support and revel in the future that we’ve helped invent, rather than lament what we think has been lost.  After all, the future is always connected to the past.  And as so eloquently phrased by Antoine Lavoisier, French nobleman, chemist and politico:  “Nothing is Lost, Nothing is Created, and Everything is Transformed.” Christine has over 25 years of diverse HR experience.  She has held HR consulting and corporate roles, including CHRO positions for Echostar in Denver, a 6,000+ employee global engineering firm, and Aepona, a startup software firm, successfully acquired by Intel. Christine is a resource to Oracle clients, to assist in Human Capital Management strategy development and implementation, compensation practices, talent development initiatives, employee engagement, global HR management, and integrated HR systems and processes that support the full employee lifecycle. 

  Read the article

• first install for windows eight.....da beta

  - by raysmithequip

  The W8 preview is now installed and I am enjoying it.  I remember the learning curve of my first unix machine back in the eighties, this ain't that.It is normal for me to do the first os install with a keyboard and low end monitor...you never know what you'll encounter out in the field.  The OS took like a fish to water.  I used a low end INTEL motherboard dp55w I gathered on the cheap, an 1157 i5 from the used bin a pair of 6 gig ddr3 sticks, a rosewell 550 watt power supply a cheap used twenty buck sub 200g wd sata drive, a half working dvd burner and an asus fanless nvidia vid card, not a great one but Sub 50.00 on newey eggey...I did have to hunt the ms forums for a key and of course to activate the thing, if dos would of needed this outmoded ritual, we would still be on cpm and osborne would be a household name, of course little do people know that this ritual was common as far back as the seventies on att unix installs....not, but it was possible, I used to joke about when I ran a bbs, what hell would of been wrought had dos 3.2 machines been required to dial into my bbs to send fido mail to ms and wait for an acknowledgement.  All in all the thing was pushing a seven on the ms richter scale, not including the vid card, sadly it came in at just a tad over three....I wanted to evaluate it for a possible replacement on critical machines that in the past went down due to a vid card fan failure....you have no idea what a customer thinks when you show them a failed vid card fan..."you mean that little plastic piece of junk caused all this!!??!!!"...yea man.  Some production machines don't need any sort of vid, I will at least keep it on the maybe list for those, MTBF is a very important factor, some big box stores should put percentage of failure rate within 24 month estimates on the outside of the carton for sure.  And a warning that the power supplies are already at their limit.  Let's face it, today even 550w can be iffy.A few neat eye candy improvements over the earlier windows is nice, the metro screen is nice, anyone who has used a newer phone recently will intuitively drag their fingers across the screen....lot of good that was with no mouse or touch screen though.  Lucky me, I have been using windows since day one, I still have a copy of win 2.0 (and every other version) for no good reason.  Still the old ix collection of disks is much larger, recompiling any kernal is another silly ritual, same machine, different day, same recompile...argh. Rh is my all time fav, mandrake was always missing something, like it rewrote the init file or something, novell is ok as long as you stay on the beaten path and of course ubuntu normally recompiles with the same errors consistantly....makes life easy that way....no errors on windows eight, just a screen that did not match the installed hardware, natuarally I alt tabbed right out of it, then hit the flag key to find the start menu....no start button. I miss the start button already. Keyboard cowboy funnin and I was browsing the harddrive, nothing stunning there, I like that, means I can find stuff. Only I can't find what I want, the start button....the start menu is that first screen for touch tablets. No biggie for useruser, that is where they will want to be, I can see that. Admins won't want to be there, it is easy enough to get the control panel a bazzilion other ways though, just not the start button. (see a pattern here?). Personally, from the keyboard I find it fun to hit the carets along the location bar at the top of the explorer screen with tabs and arrows and choose SHOW ALL CONTROL PANEL ITEMS, or thereabouts. Bottom line, I love seven and I'll love eight even more!...very happy I did not have to follow the normal rule of thumb (a customer watching me build a system and asking questions said "oh I get it, so every piece you put in there is basically a hundred bucks, right?)...ok, sure, pretty much, more or less, well, ya dude.  It will be WAY past october till I get a real touch screen but I did pick up a pair of cheap tatungs so I can try the NEW main start screen, I parse a lot of folders and have a vision of how a pair of touch screens will be easier than landing a rover on mars.  Ok.  fine, they are way smallish, and I don't expect multitouch to work but we are talking a few percent of a new 21 inch viewsonic touch screen.  Will this OS be a game changer?  I don't know.  Bottom line with all the pads and droids in the world, it is more of a catch up move at first glance.  Not something ms is used to.  An app store?  I can see ms's motivation, the others have it.  I gather there will not be gadgets there, go ahead and see what ms did  to the once populated gadget page...go ahead, google gadgets and take a gander, used to hundreds of gadgets, they are already gone.  They replaced gadgets?  sort of, I'll drop that, it's a bit of a sore point for me.  More of interest was what happened when I downloaded stuff off codeplex and some other normal programs that I like, like orbitron, top o' my list!!...cardware it is...anyways, click on the exe, get a screen, normal for windows, this one indicated that I was not running a normal windows program and had a button for  exit the install, naw, I hit details, a hidden run program anyways came into view....great, my path to the normal windows has detected a program tha.....yea ok, acl is on, fine, moving along I got orbitron installed in record time and was tracking the iss on the newest Microsoft OS, beta of course, felt like the first time I setup bsd all those year ago...FUN!!...I suppose I gotta start to think about budgeting for the real os when it comes out in october, by then I should have a rasberry pi and be done with fedora remixed.  Of course that sounds like fun too!!  I would use this OS on a tablet or phone.  I don't like the idea of being hearded to an app store, don't like that on anything, we are americans and want real choices not marketed hype, lest you are younger with opm (other peoples money).   This os would be neat on a zune, but I suspect the zune is a gonner, I am rooting for microsoft, after all their default password is not admin anymore, nor alpine,  it's blank. Others force a password, my first fawn password was so long I could not even log into it with the password in front of me, who the heck uses %$# anyways, and if I was writing a brute force attack what the heck kinda impasse is that anyways at .00001 microseconds of a code execution cycle (just a non qualified number, not a real clock speed)....AI is where it will be before too long, MS is on that path, perhaps soon someone will sit down and write an app for the kinect that watches your eyes while you scan the new main start screen, clicking on the big E icon when you blink.....boy is that going to be fun!!!! sure. Blink,dammit,blink,dammit...... OPM no doubt.I like windows eight, we are moving forwards, better keep a close eye on ubuntu.  The real clinch comes when open source becomes paid source......don't blink, I already see plenty of very expensive 'ix apps, some even in app stores already.  more to come.......

  Read the article

• Lenovo V570 CPU fan running constantly, CPU core 1 running over 90%!

  - by Rabbit2190

  I have seen that a lot of people are having this same issue. I am running a Lenovo V570 i5 4 core, 6 gigs of ram, and am running 11.10 Onieric Ocelot. On my system monitor graph it shows CPU at 20%, when I open the monitor it shows core #1 at around 90%, the other cores fluctuate at or below 5-12% if even. Now this seems like a really terrible balance of power between the cores, especially with so much stress on one core only, when these things are designed to work with 4 cores and not at such high temps. My current readings say 64 degrees Celsius, this does not seem normal for any cpu, and I am seriously considering, working on my windows7 partition until I see a real solution to this issue or upgrading to 12.04 right away when it comes out... I have seen countless things saying it has something to do with the Kernel, the kernel on mine is the same as when I upgraded, I really do not like messing with it, as when I had 11.04, I did tinker with it due to the freeze issues I was having, and that just made worse issues. I like this version 11.10 and would like to keep it for a while, but without the fear that my core is going to fry! So any help would be much appreciated! I did try changing a couple things in ACPI, and restarting this did not help, and here I am. I tried one thing prior to that that was listed under a different computer brand, but it would not do a make on the file. I really need help with this, I rely on this computer for a lot of things, and love this OS! Please help so I do not need to resort to my Microsoft partition! PLEASE! Here is the fwts cpufrequ- output: rabbit@rabbit-Lenovo-V570:~$ sudo fwts cpufreq - 00001 fwts Results generated by fwts: Version V0.23.25 (Thu Oct 6 15 00002 fwts :12:31 BST 2011). 00003 fwts 00004 fwts Some of this work - Copyright (c) 1999 - 2010, Intel Corp. 00005 fwts All rights reserved. 00006 fwts Some of this work - Copyright (c) 2010 - 2011, Canonical. 00007 fwts 00008 fwts This test run on 02/04/12 at 17:23:22 on host Linux 00009 fwts rabbit-Lenovo-V570 3.0.0-17-generic-pae #30-Ubuntu SMP Thu 00010 fwts Mar 8 17:53:35 UTC 2012 i686. 00011 fwts 00012 fwts Running tests: cpufreq. 00014 cpufreq CPU frequency scaling tests (takes ~1-2 mins). 00015 cpufreq --------------------------------------------------------- 00016 cpufreq Test 1 of 1: CPU P-State Checks. 00017 cpufreq For each processor in the system, this test steps through 00018 cpufreq the various frequency states (P-states) that the BIOS 00019 cpufreq advertises for the processor. For each processor/frequency 00020 cpufreq combination, a quick performance value is measured. The 00021 cpufreq test then validates that: 00022 cpufreq 1) Each processor has the same number of frequency states 00023 cpufreq 2) Higher advertised frequencies have a higher performance 00024 cpufreq 3) No duplicate frequency values are reported by the BIOS 00025 cpufreq 4) Is BIOS wrongly doing Sw_All P-state coordination across cores 00026 cpufreq 5) Is BIOS wrongly doing Sw_Any P-state coordination across cores 00027 cpufreq Frequency | Speed 00028 cpufreq -----------+--------- 00029 cpufreq 2.45 Ghz | 100.0 % 00030 cpufreq 2.45 Ghz | 83.7 % 00031 cpufreq 2.05 Ghz | 69.2 % 00032 cpufreq 1.85 Ghz | 62.5 % 00033 cpufreq 1.65 Ghz | 55.2 % 00034 cpufreq 1400 Mhz | 48.6 % 00035 cpufreq 1200 Mhz | 41.8 % 00036 cpufreq 1000 Mhz | 34.5 % 00037 cpufreq 800 Mhz | 27.6 % 00038 cpufreq 9 CPU frequency steps supported 00039 cpufreq Frequency | Speed 00040 cpufreq -----------+--------- 00041 cpufreq 2.45 Ghz | 97.7 % 00042 cpufreq 2.45 Ghz | 83.7 % 00043 cpufreq 2.05 Ghz | 69.6 % 00044 cpufreq 1.85 Ghz | 63.3 % 00045 cpufreq 1.65 Ghz | 55.7 % 00046 cpufreq 1400 Mhz | 48.7 % 00047 cpufreq 1200 Mhz | 41.7 % 00048 cpufreq 1000 Mhz | 34.5 % 00049 cpufreq 800 Mhz | 27.5 % 00050 cpufreq Frequency | Speed 00051 cpufreq -----------+--------- 00052 cpufreq 2.45 Ghz | 97.7 % 00053 cpufreq 2.45 Ghz | 84.4 % 00054 cpufreq 2.05 Ghz | 69.6 % 00055 cpufreq 1.85 Ghz | 62.6 % 00056 cpufreq 1.65 Ghz | 55.9 % 00057 cpufreq 1400 Mhz | 48.7 % 00058 cpufreq 1200 Mhz | 41.7 % 00059 cpufreq 1000 Mhz | 34.7 % 00060 cpufreq 800 Mhz | 27.8 % 00061 cpufreq Frequency | Speed 00062 cpufreq -----------+--------- 00063 cpufreq 2.45 Ghz | 100.0 % 00064 cpufreq 2.45 Ghz | 82.6 % 00065 cpufreq 2.05 Ghz | 67.8 % 00066 cpufreq 1.85 Ghz | 61.4 % 00067 cpufreq 1.65 Ghz | 54.9 % 00068 cpufreq 1400 Mhz | 48.3 % 00069 cpufreq 1200 Mhz | 41.1 % 00070 cpufreq 1000 Mhz | 34.3 % 00071 cpufreq 800 Mhz | 27.4 % 00072 cpufreq Frequency | Speed 00073 cpufreq -----------+--------- 00074 cpufreq 2.45 Ghz | 96.2 % 00075 cpufreq 2.45 Ghz | 82.5 % 00076 cpufreq 2.05 Ghz | 69.3 % 00077 cpufreq 1.85 Ghz | 62.7 % 00078 cpufreq 1.65 Ghz | 55.0 % 00079 cpufreq 1400 Mhz | 47.4 % 00080 cpufreq 1200 Mhz | 41.1 % 00081 cpufreq 1000 Mhz | 34.0 % 00082 cpufreq 800 Mhz | 27.2 % 00083 cpufreq Frequency | Speed 00084 cpufreq -----------+--------- 00085 cpufreq 2.45 Ghz | 96.5 % 00086 cpufreq 2.45 Ghz | 83.6 % 00087 cpufreq 2.05 Ghz | 68.1 % 00088 cpufreq 1.85 Ghz | 61.7 % 00089 cpufreq 1.65 Ghz | 54.9 % 00090 cpufreq 1400 Mhz | 48.0 % 00091 cpufreq 1200 Mhz | 41.1 % 00092 cpufreq 1000 Mhz | 34.2 % 00093 cpufreq 800 Mhz | 27.8 % 00094 cpufreq Frequency | Speed 00095 cpufreq -----------+--------- 00096 cpufreq 2.45 Ghz | 96.4 % 00097 cpufreq 2.45 Ghz | 82.6 % 00098 cpufreq 2.05 Ghz | 68.8 % 00099 cpufreq 1.85 Ghz | 60.5 % 00100 cpufreq 1.65 Ghz | 52.4 % 00101 cpufreq 1400 Mhz | 48.8 % 00102 cpufreq 1200 Mhz | 41.1 % 00103 cpufreq 1000 Mhz | 34.2 % 00104 cpufreq 800 Mhz | 26.4 % 00105 cpufreq Frequency | Speed 00106 cpufreq -----------+--------- 00107 cpufreq 2.45 Ghz | 95.3 % 00108 cpufreq 2.45 Ghz | 82.5 % 00109 cpufreq 2.05 Ghz | 65.5 % 00110 cpufreq 1.85 Ghz | 62.8 % 00111 cpufreq 1.65 Ghz | 54.8 % 00112 cpufreq 1400 Mhz | 48.0 % 00113 cpufreq 1200 Mhz | 41.2 % 00114 cpufreq 1000 Mhz | 34.2 % 00115 cpufreq 800 Mhz | 27.3 % 00116 cpufreq Frequency | Speed 00117 cpufreq -----------+--------- 00118 cpufreq 2.45 Ghz | 96.3 % 00119 cpufreq 2.45 Ghz | 83.4 % 00120 cpufreq 2.05 Ghz | 68.3 % 00121 cpufreq 1.85 Ghz | 61.9 % 00122 cpufreq 1.65 Ghz | 54.9 % 00123 cpufreq 1400 Mhz | 48.0 % 00124 cpufreq 1200 Mhz | 41.1 % 00125 cpufreq 1000 Mhz | 34.2 % 00126 cpufreq 800 Mhz | 27.3 % 00127 cpufreq Frequency | Speed 00128 cpufreq -----------+--------- 00129 cpufreq 2.45 Ghz | 100.0 % 00130 cpufreq 2.45 Ghz | 77.9 % 00131 cpufreq 2.05 Ghz | 64.6 % 00132 cpufreq 1.85 Ghz | 54.0 % 00133 cpufreq 1.65 Ghz | 51.7 % 00134 cpufreq 1400 Mhz | 45.2 % 00135 cpufreq 1200 Mhz | 39.0 % 00136 cpufreq 1000 Mhz | 33.1 % 00137 cpufreq 800 Mhz | 25.5 % 00138 cpufreq Frequency | Speed 00139 cpufreq -----------+--------- 00140 cpufreq 2.45 Ghz | 93.4 % 00141 cpufreq 2.45 Ghz | 75.7 % 00142 cpufreq 2.05 Ghz | 64.5 % 00143 cpufreq 1.85 Ghz | 59.1 % 00144 cpufreq 1.65 Ghz | 51.4 % 00145 cpufreq 1400 Mhz | 45.9 % 00146 cpufreq 1200 Mhz | 39.3 % 00147 cpufreq 1000 Mhz | 32.7 % 00148 cpufreq 800 Mhz | 25.8 % 00149 cpufreq Frequency | Speed 00150 cpufreq -----------+--------- 00151 cpufreq 2.45 Ghz | 92.1 % 00152 cpufreq 2.45 Ghz | 78.1 % 00153 cpufreq 2.05 Ghz | 65.7 % 00154 cpufreq 1.85 Ghz | 58.6 % 00155 cpufreq 1.65 Ghz | 52.5 % 00156 cpufreq 1400 Mhz | 45.7 % 00157 cpufreq 1200 Mhz | 39.3 % 00158 cpufreq 1000 Mhz | 32.7 % 00159 cpufreq 800 Mhz | 24.3 % 00160 cpufreq Frequency | Speed 00161 cpufreq -----------+--------- 00162 cpufreq 2.45 Ghz | 88.9 % 00163 cpufreq 2.45 Ghz | 79.8 % 00164 cpufreq 2.05 Ghz | 58.4 % 00165 cpufreq 1.85 Ghz | 52.6 % 00166 cpufreq 1.65 Ghz | 46.9 % 00167 cpufreq 1400 Mhz | 41.0 % 00168 cpufreq 1200 Mhz | 35.1 % 00169 cpufreq 1000 Mhz | 29.1 % 00170 cpufreq 800 Mhz | 22.9 % 00171 cpufreq Frequency | Speed 00172 cpufreq -----------+--------- 00173 cpufreq 2.45 Ghz | 92.8 % 00174 cpufreq 2.45 Ghz | 80.1 % 00175 cpufreq 2.05 Ghz | 66.2 % 00176 cpufreq 1.85 Ghz | 59.5 % 00177 cpufreq 1.65 Ghz | 52.9 % 00178 cpufreq 1400 Mhz | 46.2 % 00179 cpufreq 1200 Mhz | 39.5 % 00180 cpufreq 1000 Mhz | 32.9 % 00181 cpufreq 800 Mhz | 26.3 % 00182 cpufreq Frequency | Speed 00183 cpufreq -----------+--------- 00184 cpufreq 2.45 Ghz | 92.9 % 00185 cpufreq 2.45 Ghz | 79.5 % 00186 cpufreq 2.05 Ghz | 66.2 % 00187 cpufreq 1.85 Ghz | 59.6 % 00188 cpufreq 1.65 Ghz | 52.9 % 00189 cpufreq 1400 Mhz | 46.7 % 00190 cpufreq 1200 Mhz | 39.6 % 00191 cpufreq 1000 Mhz | 32.9 % 00192 cpufreq 800 Mhz | 26.3 % 00193 cpufreq FAILED [MEDIUM] CPUFreqCPUsSetToSW_ANY: Test 1, Processors 00194 cpufreq are set to SW_ANY. 00195 cpufreq FAILED [MEDIUM] CPUFreqSW_ANY: Test 1, Firmware not 00196 cpufreq implementing hardware coordination cleanly. Firmware using 00197 cpufreq SW_ANY instead?. 00198 cpufreq 00199 cpufreq ========================================================= 00200 cpufreq 0 passed, 2 failed, 0 warnings, 0 aborted, 0 skipped, 0 00201 cpufreq info only. 00202 cpufreq ========================================================= 00204 summary 00205 summary 0 passed, 2 failed, 0 warnings, 0 aborted, 0 skipped, 0 00206 summary info only. 00207 summary 00208 summary Test Failure Summary 00209 summary ==================== 00210 summary 00211 summary Critical failures: NONE 00212 summary 00213 summary High failures: NONE 00214 summary 00215 summary Medium failures: 2 00216 summary cpufreq test, at 1 log line: 193 00217 summary "Processors are set to SW_ANY." 00218 summary cpufreq test, at 1 log line: 195 00219 summary "Firmware not implementing hardware coordination cleanly. Firmware using SW_ANY instead?." 00220 summary 00221 summary Low failures: NONE 00222 summary 00223 summary Other failures: NONE 00224 summary 00225 summary Test |Pass |Fail |Abort|Warn |Skip |Info | 00226 summary ---------------+-----+-----+-----+-----+-----+-----+ 00227 summary cpufreq | | 2| | | | | 00228 summary ---------------+-----+-----+-----+-----+-----+-----+ 00229 summary Total: | 0| 2| 0| 0| 0| 0| 00230 summary ---------------+-----+-----+-----+-----+-----+-----+ rabbit@rabbit-Lenovo-V570:~$

  Read the article

• How does this decorator make a call to the 'register' method?

  - by BryanWheelock

  I'm trying to understand what is going on in the decorator @not_authenticated. The next step in the TraceRoute is to the method 'register' which is also located in django_authopenid/views.py which I just don't understand because I don't see anywhere that register is even mentioned in signin() How is the method 'register' called? def not_authenticated(func): """ decorator that redirect user to next page if he is already logged.""" def decorated(request, *args, **kwargs): if request.user.is_authenticated(): next = request.GET.get("next", "/") return HttpResponseRedirect(next) return func(request, *args, **kwargs) return decorated @not_authenticated def signin(request,newquestion=False,newanswer=False): """ signin page. It manage the legacy authentification (user/password) and authentification with openid. url: /signin/ template : authopenid/signin.htm """ request.encoding = 'UTF-8' on_failure = signin_failure next = clean_next(request.GET.get('next')) form_signin = OpenidSigninForm(initial={'next':next}) form_auth = OpenidAuthForm(initial={'next':next}) if request.POST: if 'bsignin' in request.POST.keys() or 'openid_username' in request.POST.keys(): form_signin = OpenidSigninForm(request.POST) if form_signin.is_valid(): next = clean_next(form_signin.cleaned_data.get('next')) sreg_req = sreg.SRegRequest(optional=['nickname', 'email']) redirect_to = "%s%s?%s" % ( get_url_host(request), reverse('user_complete_signin'), urllib.urlencode({'next':next}) ) return ask_openid(request, form_signin.cleaned_data['openid_url'], redirect_to, on_failure=signin_failure, sreg_request=sreg_req) elif 'blogin' in request.POST.keys(): # perform normal django authentification form_auth = OpenidAuthForm(request.POST) if form_auth.is_valid(): user_ = form_auth.get_user() login(request, user_) next = clean_next(form_auth.cleaned_data.get('next')) return HttpResponseRedirect(next) question = None if newquestion == True: from forum.models import AnonymousQuestion as AQ session_key = request.session.session_key qlist = AQ.objects.filter(session_key=session_key).order_by('-added_at') if len(qlist) > 0: question = qlist[0] answer = None if newanswer == True: from forum.models import AnonymousAnswer as AA session_key = request.session.session_key alist = AA.objects.filter(session_key=session_key).order_by('-added_at') if len(alist) > 0: answer = alist[0] return render('authopenid/signin.html', { 'question':question, 'answer':answer, 'form1': form_auth, 'form2': form_signin, 'msg': request.GET.get('msg',''), 'sendpw_url': reverse('user_sendpw'), }, context_instance=RequestContext(request)) Looking at the request, it seems that account/register/ does reference the register method with 'PATH_INFO': u'/account/register/' Here is the request: <WSGIRequest GET:<QueryDict: {}>, POST:<QueryDict: {u'username': [u'BryanWheelock'], u'email': [u'[email protected]'], u'bnewaccount': [u'Signup']}>, COOKIES:{'__utma': '127460431.1218630960.1266769637.1266769637.1266864494.2', '__utmb': '127460431.3.10.1266864494', '__utmc': '127460431', '__utmz': '127460431.1266769637.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none)', 'sessionid': 'fb15ee538320170a22d3a3a324aad968'}, META:{'CONTENT_LENGTH': '74', 'CONTENT_TYPE': 'application/x-www-form-urlencoded', 'DOCUMENT_ROOT': '/usr/local/apache2/htdocs', 'GATEWAY_INTERFACE': 'CGI/1.1', 'HTTP_ACCEPT': 'application/xml,application/xhtml+xml,text/html;q=0.9,text/plain;q=0.8,image/png,*/*;q=0.5', 'HTTP_ACCEPT_CHARSET': 'ISO-8859-1,utf-8;q=0.7,*;q=0.3', 'HTTP_ACCEPT_ENCODING': 'gzip,deflate,sdch', 'HTTP_ACCEPT_LANGUAGE': 'en-US,en;q=0.8', 'HTTP_CACHE_CONTROL': 'max-age=0', 'HTTP_CONNECTION': 'close', 'HTTP_COOKIE': '__utmz=127460431.1266769637.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none); __utma=127460431.1218630960.1266769637.1266769637.1266864494.2; __utmc=127460431; __utmb=127460431.3.10.1266864494; sessionid=fb15ee538320170a22d3a3a324aad968', 'HTTP_HOST': 'workproject.com', 'HTTP_ORIGIN': 'http://workproject.com', 'HTTP_REFERER': 'http://workproject.com/account/signin/complete/?next=%2F&janrain_nonce=2010-02-22T18%3A49%3A53ZG2KXci&openid.ns=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0&openid.mode=id_res&openid.op_endpoint=https%3A%2F%2Fwww.google.com%2Faccounts%2Fo8%2Fud&openid.response_nonce=2010-02-22T18%3A49%3A53Znxxxxxxxxxw&openid.return_to=http%3A%2F%2Fworkproject.com%2Faccount%2Fsignin%2Fcomplete%2F%3Fnext%3D%252F%26janrain_nonce%3D2010-02-22T18%253A49%253A53ZG2KXci&openid.assoc_handle=AOQobUepU4xs-kGg5LiyLzfN3RYv0I0Jocgjf_1odT4RR9zfMFpQVpMg&openid.signed=op_endpoint%2Cclaimed_id%2Cidentity%2Creturn_to%2Cresponse_nonce%2Cassoc_handle&openid.sig=Jf76i2RNhqpLTJMjeQ0nnQz6fgA%3D&openid.identity=https%3A%2F%2Fwww.google.com%2Faccounts%2Fo8%2Fid%3Fid%3DAItxxxxxxxxxs9CxHQ3PrHw_N5_3j1HM&openid.claimed_id=https%3A%2F%2Fwww.google.com%2Faccounts%2Fo8%2Fid%3Fid%3DAItOaxxxxxxxxxxx4s9CxHQ3PrHw_N5_3j1HM', 'HTTP_USER_AGENT': 'Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10_5_8; en-US) AppleWebKit/532.9 (KHTML, like Gecko) Chrome/5.0.307.7 Safari/532.9', 'HTTP_X_FORWARDED_FOR': '96.8.31.235', 'PATH': '/usr/bin:/bin', 'PATH_INFO': u'/account/register/', 'PATH_TRANSLATED': '/home/spirituality/webapps/work/spirit_app.wsgi/account/register/', 'QUERY_STRING': '', 'REMOTE_ADDR': '127.0.0.1', 'REMOTE_PORT': '59956', 'REQUEST_METHOD': 'POST', 'REQUEST_URI': '/account/register/', 'SCRIPT_FILENAME': '/home/spirituality/webapps/spirituality/spirit_app.wsgi', 'SCRIPT_NAME': u'', 'SERVER_ADDR': '127.0.0.1', 'SERVER_ADMIN': '[no address given]', 'SERVER_NAME': 'workproject.com', 'SERVER_PORT': '80', 'SERVER_PROTOCOL': 'HTTP/1.0', 'SERVER_SIGNATURE': '', 'SERVER_SOFTWARE': 'Apache/2.2.12 (Unix) mod_wsgi/2.5 Python/2.5.4', 'mod_wsgi.application_group': 'www.workProject.com|', 'mod_wsgi.callable_object': 'application', 'mod_wsgi.listener_host': '', 'mod_wsgi.listener_port': '25931', 'mod_wsgi.process_group': '', 'mod_wsgi.reload_mechanism': '0', 'mod_wsgi.script_reloading': '1', 'mod_wsgi.version': (2, 5), 'wsgi.errors': <mod_wsgi.Log object at 0xb7ce0038>, 'wsgi.file_wrapper': <built-in method file_wrapper of mod_wsgi.Adapter object at 0xb7e94b18>, 'wsgi.input': <mod_wsgi.Input object at 0x999cc78>, 'wsgi.multiprocess': True, 'wsgi.multithread': False, 'wsgi.run_once': False, 'wsgi.url_scheme': 'http', 'wsgi.version': (1, 0)}>

  Read the article

• OS X 10.9 Mavericks Kernel Panics out of the box

  - by Kevin

  OS X Kernel panics after a fresh install of OS X 10.9 on a 17" Macbook Pro. Anonymous UUID: D002464D-24B7-C2B5-3D83-1C0B02873B29 Wed Oct 30 11:08:17 2013 panic(cpu 1 caller 0xffffff8006edc19e): Kernel trap at 0xffffff7f88e0a96c, type 14=page fault, registers: CR0: 0x000000008001003b, CR2: 0xffffef7f88e309b8, CR3: 0x0000000009c2d000, CR4: 0x0000000000000660 RAX: 0x0fffffd0c7b30000, RBX: 0xffffef7f88e309b0, RCX: 0x0000000000000001, RDX: 0x000002f384d06471 RSP: 0xffffff80eff03d80, RBP: 0xffffff80eff03e70, RSI: 0x0000031384cfb168, RDI: 0xffffff80e8f05148 R8: 0xffffff801b0f8670, R9: 0x0000000000000005, R10: 0x0000000000004a24, R11: 0x0000000000000202 R12: 0xffffff801938b800, R13: 0x0000000000000005, R14: 0xffffff80e8f05148, R15: 0xffffff7f88e2ee20 RFL: 0x0000000000010006, RIP: 0xffffff7f88e0a96c, CS: 0x0000000000000008, SS: 0x0000000000000010 Fault CR2: 0xffffef7f88e309b8, Error code: 0x0000000000000002, Fault CPU: 0x1 Backtrace (CPU 1), Frame : Return Address 0xffffff80eff03a10 : 0xffffff8006e22f69 0xffffff80eff03a90 : 0xffffff8006edc19e 0xffffff80eff03c60 : 0xffffff8006ef3606 0xffffff80eff03c80 : 0xffffff7f88e0a96c 0xffffff80eff03e70 : 0xffffff7f88e09b89 0xffffff80eff03f30 : 0xffffff8006edda5c 0xffffff80eff03f50 : 0xffffff8006e3757a 0xffffff80eff03f90 : 0xffffff8006e378c8 0xffffff80eff03fb0 : 0xffffff8006ed6aa7 Kernel Extensions in backtrace: com.apple.driver.AppleIntelCPUPowerManagement(216.0)[A6EE4D7B-228E-3A3C-95BA-10ED6F331236]@0xffffff7f88e07000->0xffffff7f88e31fff BSD process name corresponding to current thread: kernel_task Mac OS version: 13A603 Kernel version: Darwin Kernel Version 13.0.0: Thu Sep 19 22:22:27 PDT 2013; root:xnu-2422.1.72~6/RELEASE_X86_64 Kernel UUID: 1D9369E3-D0A5-31B6-8D16-BFFBBB390393 Kernel slide: 0x0000000006c00000 Kernel text base: 0xffffff8006e00000 System model name: MacBookPro5,2 (Mac-F2268EC8) System uptime in nanoseconds: 4634353513870 last loaded kext at 39203945245: com.viscosityvpn.Viscosity.tun 1.0 (addr 0xffffff7f89200000, size 32768) last unloaded kext at 147930318702: com.apple.driver.AppleFileSystemDriver 3.0.1 (addr 0xffffff7f89110000, size 8192) loaded kexts: com.viscosityvpn.Viscosity.tun 1.0 com.viscosityvpn.Viscosity.tap 1.0 com.apple.driver.AudioAUUC 1.60 com.apple.driver.AppleHWSensor 1.9.5d0 com.apple.filesystems.autofs 3.0 com.apple.iokit.IOBluetoothSerialManager 4.2.0f6 com.apple.driver.AGPM 100.14.11 com.apple.driver.AppleMikeyHIDDriver 124 com.apple.driver.AppleHDA 2.5.2fc2 com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.2.0f6 com.apple.GeForceTesla 8.1.8 com.apple.driver.AppleMikeyDriver 2.5.2fc2 com.apple.iokit.IOUserEthernet 1.0.0d1 com.apple.driver.AppleUpstreamUserClient 3.5.13 com.apple.driver.AppleMuxControl 3.4.12 com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0 com.apple.driver.AppleSMCLMU 2.0.4d1 com.apple.Dont_Steal_Mac_OS_X 7.0.0 com.apple.driver.AppleHWAccess 1 com.apple.driver.AppleMCCSControl 1.1.12 com.apple.driver.AppleLPC 1.7.0 com.apple.driver.SMCMotionSensor 3.0.4d1 com.apple.driver.AppleUSBTCButtons 240.2 com.apple.driver.AppleUSBTCKeyboard 240.2 com.apple.driver.AppleIRController 325.7 com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1 com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1 com.apple.BootCache 35 com.apple.iokit.SCSITaskUserClient 3.6.0 com.apple.driver.XsanFilter 404 com.apple.iokit.IOAHCIBlockStorage 2.4.0 com.apple.driver.AppleUSBHub 650.4.4 com.apple.driver.AppleUSBEHCI 650.4.1 com.apple.driver.AppleFWOHCI 4.9.9 com.apple.driver.AirPort.Brcm4331 700.20.22 com.apple.driver.AppleAHCIPort 2.9.5 com.apple.nvenet 2.0.21 com.apple.driver.AppleUSBOHCI 650.4.1 com.apple.driver.AppleSmartBatteryManager 161.0.0 com.apple.driver.AppleRTC 2.0 com.apple.driver.AppleHPET 1.8 com.apple.driver.AppleACPIButtons 2.0 com.apple.driver.AppleSMBIOS 2.0 com.apple.driver.AppleACPIEC 2.0 com.apple.driver.AppleAPIC 1.7 com.apple.driver.AppleIntelCPUPowerManagementClient 216.0.0 com.apple.nke.applicationfirewall 153 com.apple.security.quarantine 3 com.apple.driver.AppleIntelCPUPowerManagement 216.0.0 com.apple.kext.triggers 1.0 com.apple.iokit.IOSerialFamily 10.0.7 com.apple.AppleGraphicsDeviceControl 3.4.12 com.apple.driver.DspFuncLib 2.5.2fc2 com.apple.vecLib.kext 1.0.0 com.apple.iokit.IOAudioFamily 1.9.4fc11 com.apple.kext.OSvKernDSPLib 1.14 com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.2.0f6 com.apple.iokit.IOSurface 91 com.apple.iokit.IOBluetoothFamily 4.2.0f6 com.apple.nvidia.classic.NVDANV50HalTesla 8.1.8 com.apple.driver.AppleSMBusPCI 1.0.12d1 com.apple.driver.AppleGraphicsControl 3.4.12 com.apple.driver.IOPlatformPluginLegacy 1.0.0 com.apple.driver.AppleBacklightExpert 1.0.4 com.apple.iokit.IOFireWireIP 2.2.5 com.apple.driver.AppleHDAController 2.5.2fc2 com.apple.iokit.IOHDAFamily 2.5.2fc2 com.apple.driver.AppleSMBusController 1.0.11d1 com.apple.nvidia.classic.NVDAResmanTesla 8.1.8 com.apple.driver.IOPlatformPluginFamily 5.5.1d27 com.apple.iokit.IONDRVSupport 2.3.6 com.apple.iokit.IOGraphicsFamily 2.3.6 com.apple.driver.AppleSMC 3.1.6d1 com.apple.driver.AppleUSBMultitouch 240.6 com.apple.iokit.IOUSBHIDDriver 650.4.4 com.apple.driver.AppleUSBMergeNub 650.4.0 com.apple.driver.AppleUSBComposite 650.4.0 com.apple.driver.CoreStorage 380 com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.6.0 com.apple.iokit.IOBDStorageFamily 1.7 com.apple.iokit.IODVDStorageFamily 1.7.1 com.apple.iokit.IOCDStorageFamily 1.7.1 com.apple.iokit.IOAHCISerialATAPI 2.6.0 com.apple.iokit.IOSCSIArchitectureModelFamily 3.6.0 com.apple.iokit.IOUSBUserClient 650.4.4 com.apple.iokit.IOFireWireFamily 4.5.5 com.apple.iokit.IO80211Family 600.34 com.apple.iokit.IOAHCIFamily 2.6.0 com.apple.iokit.IONetworkingFamily 3.2 com.apple.iokit.IOUSBFamily 650.4.4 com.apple.driver.NVSMU 2.2.9 com.apple.driver.AppleEFINVRAM 2.0 com.apple.driver.AppleEFIRuntime 2.0 com.apple.iokit.IOHIDFamily 2.0.0 com.apple.iokit.IOSMBusFamily 1.1 com.apple.security.sandbox 278.10 com.apple.kext.AppleMatch 1.0.0d1 com.apple.security.TMSafetyNet 7 com.apple.driver.AppleKeyStore 2 com.apple.driver.DiskImages 371.1 com.apple.iokit.IOStorageFamily 1.9 com.apple.iokit.IOReportFamily 21 com.apple.driver.AppleFDEKeyStore 28.30 com.apple.driver.AppleACPIPlatform 2.0 com.apple.iokit.IOPCIFamily 2.8 com.apple.iokit.IOACPIFamily 1.4 com.apple.kec.pthread 1 com.apple.kec.corecrypto 1.0 System Profile: Model: MacBookPro5,2, BootROM MBP52.008E.B05, 2 processors, Intel Core 2 Duo, 2.8 GHz, 8 GB, SMC 1.42f4 Graphics: NVIDIA GeForce 9400M, NVIDIA GeForce 9400M, PCI, 256 MB Graphics: NVIDIA GeForce 9600M GT, NVIDIA GeForce 9600M GT, PCIe, 512 MB Memory Module: BANK 0/DIMM0, 4 GB, DDR3, 1333 MHz, 0x04CD, 0x46332D3130363636434C392D344742535100 Memory Module: BANK 1/DIMM0, 4 GB, DDR3, 1333 MHz, 0x04CD, 0x46332D3130363636434C392D344742535100 AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 (5.106.98.100.22) Bluetooth: Version 4.2.0f6 12982, 3 services, 15 devices, 1 incoming serial ports Network Service: Wi-Fi, AirPort, en1 Serial ATA Device: Samsung SSD 840 Series, 120.03 GB Serial ATA Device: MATSHITADVD-R UJ-868 USB Device: Built-in iSight USB Device: BRCM2046 Hub USB Device: Bluetooth USB Host Controller USB Device: Apple Internal Keyboard / Trackpad USB Device: IR Receiver Thunderbolt Bus:

  Read the article

• 'undefined method init for Mysql:Class'

  - by sscirrus

  I've been having problems with a MySQL Server installation that got messed up after a power outage. Configuration Intel i5 Mac running OS X 10.6.5 Ruby 1.9.2 installed Rails 3.0.1 installed MySQL Server (finally) installed and running I completely reinstalled MySQL, which deleted the local development/test/production databases. So, I have run create database development; in MySQL to get the dev database ready for a migration. Current Goal Run rake db:migrate to get my databases back again. (I cannot currently access my databases or Mysql at all from Rails.) Error Using the gem 'mysql', '2.8.1' and run rake db:migrate, I get the error: rake aborted! undefined method 'init' for Mysql:Class Stack Trace: /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/connection_adapters/mysql_adapter.rb:30:in 'mysql_connection' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/connection_adapters/abstract/connection_pool.rb:230:in 'new_connection' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/connection_adapters/abstract/connection_pool.rb:238:in 'checkout_new_connection' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/connection_adapters/abstract/connection_pool.rb:194:in 'block (2 levels) in checkout' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/connection_adapters/abstract/connection_pool.rb:190:in 'loop' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/connection_adapters/abstract/connection_pool.rb:190:in 'block in checkout' /Users/sscirrus/.rvm/rubies/ruby-1.9.2-p0/lib/ruby/1.9.1/monitor.rb:201:in 'mon_synchronize' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/connection_adapters/abstract/connection_pool.rb:189:in 'checkout' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/connection_adapters/abstract/connection_pool.rb:96:in 'connection' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/connection_adapters/abstract/connection_pool.rb:318:in 'retrieve_connection' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/connection_adapters/abstract/connection_specification.rb:97:in 'retrieve_connection' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/connection_adapters/abstract/connection_specification.rb:89:in 'connection' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/migration.rb:486:in 'initialize' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/migration.rb:433:in 'new' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/migration.rb:433:in 'up' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/migration.rb:415:in 'migrate' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/activerecord-3.0.1/lib/active_record/railties/databases.rake:142:in 'block (2 levels) in <top (required)>' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:636:in 'call' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:636:in 'block in execute' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:631:in 'each' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:631:in 'execute' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:597:in 'block in invoke_with_call_chain' /Users/sscirrus/.rvm/rubies/ruby-1.9.2-p0/lib/ruby/1.9.1/monitor.rb:201:in 'mon_synchronize' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:590:in 'invoke_with_call_chain' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:583:in 'invoke' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:2051:in 'invoke_task' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:2029:in 'block (2 levels) in top_level' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:2029:in 'each' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:2029:in 'block in top_level' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:2068:in 'standard_exception_handling' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:2023:in 'top_level' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:2001:in 'block in run' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:2068:in 'standard_exception_handling' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/lib/rake.rb:1998:in 'run' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/gems/rake-0.8.7/bin/rake:31:in '<top (required)>' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/bin/rake:19:in 'load' /Users/sscirrus/.rvm/gems/ruby-1.9.2-p0/bin/rake:19:in '<main>'

  Read the article

• PHP pages working slow from time to time

  - by user1038179

  I have VPS with limit of 2GB of ram and 8 CPU cores. I have 5 sites on that VPS (one of them is just for testing, no visitors exept me). All 5 sites are image galleries, like wallpaper sites. Last week I noticed problem on one site (main domain, used for name servers, and also with most traffic, visitors). That site has two image galleries, one is old static html gallery made few years ago and another, main, is powered by ZENPhoto CMS. Also I have that same gallery CMS on another two sites on that same VPS (on one running site and on one just for testing site). On other two sites I have diferent PHP driven gallery. Problem is that after some time (it vary from 10 minutes to few hours after apache restart), loading of pages on main site becomes very slow, or I get 503 Service Temporarily Unavailable error. So pages becomes unavailable. But just that part with new CMS gallery, old part of site with static html pages are working fast and just fine. Also other two sites with same CMS gallery and other two with different PHP driven gallery are working fine and fast at the same time. I thought it must be something with CMS on that main site, because other sites are working nice. Then I tryed to open contact and guest book pages on that main site which are outside of that CMS but also PHP pages, and they do not load too, but that same contact php scipts are working on other sites at the same time. So, when site starts to hangs, ONLY PHP generated content is not working, like I said other static pages are working. And, ONLY on that one main site I have problems. Then I need to restart Apache, after restart everything is vorking nice and fast, for some time, than again, just PHP pages on main site are becomming slower. If I do not restart apache that slowness take some time (several minutes, hours, depending ot traffic) and during that time PHP diven content is loading very slow or unavailable on that site. After sime time, on moments everything start to work and is fast again for some time, and again. In hours with more traffic PHP content is loading slowly or it is unavailable, in hours with less traffic it is sometimes fast and sometimes little bit slower than usually. And ones again, only on that main site, and only PHP driven pages, static pages are working fast even in most traffic hours also other sites with even same CMS are working fast. Currently I have about 7000 unique visitors on that site but site worked nice even with 11500 visitors per day. And about 17000 in total visitors on VPS, all sites ( about 3 pages per unique visitor). When site start to slow down sometimes in apache status I can see something like this: mod_fcgid status: Total FastCGI processes: 37 Process: php5 (/usr/local/cpanel/cgi-sys/php5)Pid Active Idle Accesses State 11300 39 28 7 Working 11274 47 28 7 Working 11296 40 29 3 Working 11283 45 30 3 Working 11304 36 31 1 Working 11282 46 32 3 Working 11292 42 33 1 Working 11289 44 34 1 Working 11305 35 35 0 Working 11273 48 36 2 Working 11280 47 39 1 Working 10125 133 40 12 Exiting(communication error) 11294 41 41 1 Exiting(communication error) 11277 47 42 2 Exiting(communication error) 11291 43 43 1 Exiting(communication error) 10187 108 43 10 Exiting(communication error) 10209 95 44 7 Exiting(communication error) 10171 113 44 5 Exiting(communication error) 11275 47 47 1 Exiting(communication error) 10144 125 48 8 Exiting(communication error) 10086 149 48 20 Exiting(communication error) 10212 94 49 5 Exiting(communication error) 10158 118 49 5 Exiting(communication error) 10169 114 50 4 Exiting(communication error) 10105 141 50 16 Exiting(communication error) 10094 146 50 15 Exiting(communication error) 10115 139 51 17 Exiting(communication error) 10213 93 51 9 Exiting(communication error) 10197 103 51 7 Exiting(communication error) Process: php5 (/usr/local/cpanel/cgi-sys/php5)Pid Active Idle Accesses State 7983 1079 2 149 Ready 7979 1079 11 151 Ready Process: php5 (/usr/local/cpanel/cgi-sys/php5)Pid Active Idle Accesses State 7990 1066 0 57 Ready 8001 1031 64 35 Ready 7999 1032 94 29 Ready 8000 1031 91 36 Ready 8002 1029 34 52 Ready Process: php5 (/usr/local/cpanel/cgi-sys/php5)Pid Active Idle Accesses State 7991 1064 29 115 Ready When it is working nicly there is no lines with "Exiting(communication error)" Active and Idle are time active and time since last request, in seconds. Here are system info. Sysem info: Total processors: 8 Processor #1 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5440 @ 2.83GHz Speed 88.320 MHz Cache 6144 KB All other seven are the same. System Information Linux vps.nnnnnnnnnnnnnnnnn.nnn 2.6.18-028stab099.3 #1 SMP Wed Mar 7 15:20:22 MSK 2012 x86_64 x86_64 x86_64 GNU/Linux Current Memory Usage total used free shared buffers cached Mem: 8388608 882164 7506444 0 0 0 -/+ buffers/cache: 882164 7506444 Swap: 0 0 0 Total: 8388608 882164 7506444 Current Disk Usage Filesystem Size Used Avail Use% Mounted on /dev/vzfs 100G 34G 67G 34% / none System Details: Running on: Apache/2.2.22 System info: (Unix) mod_ssl/2.2.22 OpenSSL/0.9.8e-fips-rhel5 DAV/2 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 mod_fcgid/2.3.6 Powered by: PHP/5.3.10 Current Configuration Default PHP Version (.php files) 5 PHP 5 Handler fcgi PHP 4 Handler suphp Apache suEXEC on Apache Ruid2 off PHP 4 Handler suphp Apache suEXEC on Apache Configuration The following settings have been saved: fileetag: All keepalive: On keepalivetimeout: 3 maxclients: 150 maxkeepaliverequests: 10 maxrequestsperchild: 10000 maxspareservers: 10 minspareservers: 5 root_options: ExecCGI, FollowSymLinks, Includes, IncludesNOEXEC, Indexes, MultiViews, SymLinksIfOwnerMatch serverlimit: 256 serversignature: Off servertokens: Full sslciphersuite: ALL:!ADH:RC4+RSA:+HIGH:+MEDIUM:-LOW:-SSLv2:-EXP:!kEDH startservers: 5 timeout: 30 I hope, I explained my problem nicely. Any help would be nice.

  Read the article

• All downloads being interrupted

  - by Jake

  System: Windows 7 Professional 64bit. 8GB RAM, Intel i5-2400 CPU, +300GB free on the hard drive. AVG Internet Security 2012 (enabled & disabled, with firewall enabled and disabled - no effect for either). This computer is less than a year old. Network: This problem is occurring on a single computer on a network with multiple computers. The router is a Motorola Netopia 3347-02 (DSL Modem/Wireless Router combined). The computer is plugged in directly to the modem, other computers are using the wireless successfully. The router has been reset. The only thing odd about the connection between the router and computer is that it is configured to allow RDP through, so it is assigned a static IP by the router and port forwarding is enabled for port 3389. Also, though I doubt it matters, a second wireless router is active behind this router providing a second network that some computers in the area use without issues. Details: All downloads initiated on this specific computer eventually fail, this includes streaming from youtube, specialized downloads (itunes), downloads from websites, FTP downloads, etc. Failure occurs with all browsers, but in chrome this is the process it takes: 1) Download begins normally, 2) At some point between (observed) 7MBs and 229MBs the download stops progressing (at this point, if watching chrome's task manager, you can see the network activity for the downloading tab drop to 0kps), 3) for some time the download sits there still attempting to complete, but will eventually display "123,049,871/0 B, Interrupted" (where the number is whatever it actually got to). The file I am using to test this is a very large .zip file located on a server I control, but the problem seems to occur on any site. The amount downloaded is completely random, and seems to be more time-based than anything (if I start a download immediately after the last one fails, it tends to get further than the last one). Small files can get through for this reason, though they can fail as well. In a test where I simultaneously downloaded the same file via HTTP (chrome) and FTP (windows explorer), both downloads failed at the same instant, though explorer displayed "Connection timed out" several minutes before chrome finally showed the download as interrupted. Other things I have tried based on advice given to people with similar/identical problems: Setting my MTU to 1492 (as described here: http://blog.thecompwiz.com/2011/08/networking-issues.html) Disabling write caching to the hard drive storing the download on an external device successfully transmitted +1GB file from one computer on the same network to this computer disabling indexing in the folder the download was being stored in disabling all security software checked to make sure all drivers were up to date read about 50 accounts with nearly exact descriptions of what I'm experiencing, none of which had a solution given Running Processes: Image Name PID Session Name Session# Mem Usage ========================= ======== ================ =========== ============ System Idle Process 0 Services 0 24 K System 4 Services 0 104,836 K smss.exe 332 Services 0 1,276 K csrss.exe 764 Services 0 5,060 K wininit.exe 820 Services 0 4,748 K csrss.exe 844 Console 1 23,764 K services.exe 876 Services 0 11,856 K lsass.exe 892 Services 0 14,420 K lsm.exe 900 Services 0 7,820 K winlogon.exe 944 Console 1 7,716 K svchost.exe 428 Services 0 12,744 K svchost.exe 796 Services 0 12,240 K svchost.exe 1036 Services 0 22,372 K svchost.exe 1084 Services 0 174,132 K svchost.exe 1112 Services 0 56,144 K svchost.exe 1288 Services 0 18,640 K svchost.exe 1404 Services 0 29,616 K spoolsv.exe 1576 Services 0 25,924 K svchost.exe 1616 Services 0 12,788 K AppleMobileDeviceService. 1728 Services 0 9,796 K avgwdsvc.exe 1820 Services 0 8,268 K mDNSResponder.exe 1844 Services 0 5,832 K w3dbsmgr.exe 1108 Services 0 43,760 K QBCFMonitorService.exe 1336 Services 0 16,408 K svchost.exe 2404 Services 0 28,240 K taskhost.exe 3020 Console 1 12,372 K dwm.exe 2280 Console 1 5,968 K explorer.exe 2964 Console 1 152,476 K WUDFHost.exe 3316 Services 0 6,740 K svchost.exe 3408 Services 0 5,556 K RAVCpl64.exe 3684 Console 1 13,864 K igfxtray.exe 3700 Console 1 7,804 K hkcmd.exe 3772 Console 1 7,868 K igfxpers.exe 3788 Console 1 10,940 K sidebar.exe 3836 Console 1 84,400 K chrome.exe 3964 Console 1 19,640 K pptd40nt.exe 4068 Console 1 5,156 K acrotray.exe 3908 Console 1 14,676 K avgtray.exe 3872 Console 1 9,508 K jusched.exe 4076 Console 1 4,412 K iTunesHelper.exe 1532 Console 1 87,308 K SearchIndexer.exe 3492 Services 0 36,948 K iPodService.exe 4136 Services 0 7,944 K BrccMCtl.exe 4276 Console 1 18,132 K splwow64.exe 4380 Console 1 32,600 K qbupdate.exe 4836 Console 1 24,236 K svchost.exe 4288 Services 0 20,700 K wmpnetwk.exe 3112 Services 0 9,516 K FNPLicensingService.exe 5248 Services 0 5,852 K QBW32.EXE 5508 Console 1 127,068 K QBDBMgrN.exe 5600 Services 0 42,252 K EXCEL.EXE 2512 Console 1 99,100 K LMS.exe 3188 Services 0 5,616 K UNS.exe 1600 Services 0 7,308 K axlbridge.exe 5260 Console 1 5,132 K chrome.exe 5888 Console 1 200,336 K chrome.exe 3536 Console 1 26,076 K chrome.exe 1952 Console 1 20,168 K chrome.exe 4596 Console 1 24,696 K chrome.exe 4292 Console 1 48,096 K chrome.exe 2796 Console 1 23,520 K Acrobat.exe 1240 Console 1 87,252 K 123w.exe 4892 Console 1 22,728 K calc.exe 1700 Console 1 12,636 K chrome.exe 1328 Console 1 28,888 K chrome.exe 3696 Console 1 47,012 K rundll32.exe 6320 Console 1 7,104 K chrome.exe 4928 Console 1 44,248 K AVGIDSAgent.exe 260 Services 0 12,940 K avgfws.exe 6052 Services 0 26,912 K avgnsa.exe 5064 Services 0 2,496 K avgrsa.exe 3088 Services 0 2,200 K avgcsrva.exe 2596 Services 0 380 K avgcsrva.exe 6948 Services 0 408 K StikyNot.exe 452 Console 1 14,772 K chrome.exe 4580 Console 1 28,200 K chrome.exe 4016 Console 1 57,756 K svchost.exe 7140 Services 0 4,500 K chrome.exe 6264 Console 1 56,824 K chrome.exe 7008 Console 1 56,896 K chrome.exe 2224 Console 1 38,032 K taskhost.exe 612 Console 1 7,228 K chrome.exe 6000 Console 1 10,928 K chrome.exe 2568 Console 1 43,052 K chrome.exe 272 Console 1 75,988 K chrome.exe 7328 Console 1 53,240 K PaprPort.exe 7976 Console 1 137,152 K pplinks.exe 7500 Console 1 14,052 K ppscanmg.exe 5744 Console 1 18,996 K taskeng.exe 7388 Console 1 6,308 K SearchProtocolHost.exe 8024 Services 0 8,804 K SearchFilterHost.exe 7232 Services 0 7,848 K chrome.exe 8016 Console 1 37,440 K cmd.exe 7692 Console 1 3,096 K conhost.exe 7516 Console 1 5,872 K tasklist.exe 8160 Console 1 5,772 K WmiPrvSE.exe 7684 Services 0 6,400 K Any help with this would be greatly appreciated, I've been beating my head against a wall over this all day. This computer serves dual purpose as the main company document server and the Owner's work computer, it's fairly important it be fully functional and I cannot figure this out.

  Read the article

• Load-balancing between a Procurve switch and a server

  - by vlad

  Hello I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work? My setup is as follows: I have a central switch, a Procurve 2510G-24, image version Y.11.16. It's the center of a star topology, there are four switches connected to it via a single gigabit link. Those switches service the users. On the central switch, I have a server with two gigabit interfaces that I want to bond together in order to achieve higher throughput, and two other servers that have single gigabit connections to the switch. The topology looks as follows: sw1 sw2 sw3 sw4 | | | | --------------------- | sw0 | --------------------- || | | srv1 srv2 srv3 The servers were running FreeBSD 8.1. On srv1 I set up a lagg interface using the lacp protocol, and on the switch I set up a trunk for the two ports using lacp as well. The switch showed that the server was a lacp partner, I could ping the server from another computer, and the server could ping other computers. If I unplugged one of the cables, the connection would keep working, so everything looked fine. Until I tested throughput. There was only one link used between srv1 and sw0. All testing was conducted with iperf, and load distribution was checked with systat -ifstat. I was looking to test the load balancing for both receive and send operations, as I want this server to be a file server. There were therefore two scenarios: iperf -s on srv1 and iperf -c on the other servers iperf -s on the other servers and iperf -c on srv1 connected to all the other servers. Every time only one link was used. If one cable was unplugged, the connections would keep going. However, once the cable was plugged back in, the load was not distributed. Each and every server is able to fill the gigabit link. In one-to-one test scenarios, iperf was reporting around 940Mbps. The CPU usage was around 20%, which means that the servers could withstand a doubling of the throughput. srv1 is a dell poweredge sc1425 with onboard intel 82541GI nics (em driver on freebsd). After troubleshooting a previous problem with vlan tagging on top of a lagg interface, it turned out that the em could not support this. So I figured that maybe something else is wrong with the em drivers and / or lagg stack, so I started up backtrack 4r2 on this same server. So srv1 now uses linux kernel 2.6.35.8. I set up a bonding interface bond0. The kernel module was loaded with option mode=4 in order to get lacp. The switch was happy with the link, I could ping to and from the server. I could even put vlans on top of the bonding interface. However, only half the problem was solved: if I used srv1 as a client to the other servers, iperf was reporting around 940Mbps for each connection, and bwm-ng showed, of course, a nice distribution of the load between the two nics; if I run the iperf server on srv1 and tried to connect with the other servers, there was no load balancing. I thought that maybe I was out of luck and the hashes for the two mac addresses of the clients were the same, so I brought in two new servers and tested with the four of them at the same time, and still nothing changed. I tried disabling and reenabling one of the links, and all that happened was the traffic switched from one link to the other and back to the first again. I also tried setting the trunk to "plain trunk mode" on the switch, and experimented with other bonding modes (roundrobin, xor, alb, tlb) but I never saw any traffic distribution. One interesting thing, though: one of the four switches is a Cisco 2950, image version 12.1(22)EA7. It has 48 10/100 ports and 2 gigabit uplinks. I have a server (call it srv4) with a 4 channel trunk connected to it (4x100), FreeBSD 8.0 release. The switch is connected to sw0 via gigabit. If I set up an iperf server on one of the servers connected to sw0 and a client on srv4, ALL 4 links are used, and iperf reports around 330Mbps. systat -ifstat shows all four interfaces are used. The cisco port-channel uses src-mac to balance the load. The HP should use both the source and destination according to the manual, so it should work as well. Could this mean there is some bug in the HP firmware? Am I doing something wrong?

  Read the article

• Problem simulating HTTP POST using HttpClient

  - by user560904

  I am trying to programatically send a HTTP Post request using HttpClient to http://ojp.nationalrail.co.uk/en/s/planjourney/query but it is not liking the request I send it. I copied the headers and body from what Chrome browser sends so it is identical but it doesn't like what I send as the HTML mentions there's an error. <div class="padding"> <h1 class="sifr"><strong>Sorry</strong>, something went wrong</h1> <div class="error-message"> <div class="error-message-padding"> <h2>There is a problem with the page you are trying to access.</h2> <p>It is possible that it was either moved, it doesn't exist or we are experiencing some technical difficulties.</p> <p>We are sorry for the inconvenience.</p> </div> </div> </div> Here is my Java program which uses HttpClient: package com.tixsnif; import org.apache.http.*; import org.apache.http.client.HttpClient; import org.apache.http.client.entity.UrlEncodedFormEntity; import org.apache.http.client.methods.HttpPost; import org.apache.http.impl.client.DefaultHttpClient; import org.apache.http.message.BasicNameValuePair; import org.apache.http.protocol.HTTP; import java.io.*; import java.util.*; import java.util.zip.GZIPInputStream; public class WebScrapingTesting { public static void main(String[] args) throws Exception { String target = "http://ojp.nationalrail.co.uk/en/s/planjourney/query"; HttpClient client = new DefaultHttpClient(); HttpPost httpPost = new HttpPost(target); BasicNameValuePair[] params = { new BasicNameValuePair("jpState", "single"), new BasicNameValuePair("commandName", "journeyPlannerCommand"), new BasicNameValuePair("from.searchTerm", "Basingstoke"), new BasicNameValuePair("to.searchTerm", "Reading"), new BasicNameValuePair("timeOfOutwardJourney.arrivalOrDeparture", "DEPART"), new BasicNameValuePair("timeOfOutwardJourney.monthDay", "Today"), new BasicNameValuePair("timeOfOutwardJourney.hour", "10"), new BasicNameValuePair("timeOfOutwardJourney.minute", "15"), new BasicNameValuePair("timeOfReturnJourney.arrivalOrDeparture", "DEPART"), new BasicNameValuePair("timeOfReturnJourney.monthDay", "Today"), new BasicNameValuePair("timeOfReturnJourney.hour", "18"), new BasicNameValuePair("timeOfReturnJourney.minute", "15"), new BasicNameValuePair("_includeOvertakenTrains", "on"), new BasicNameValuePair("viaMode", "VIA"), new BasicNameValuePair("via.searchTerm", "Station name / code"), new BasicNameValuePair("offSetOption", "0"), new BasicNameValuePair("_reduceTransfers", "on"), new BasicNameValuePair("operatorMode", "SHOW"), new BasicNameValuePair("operator.code", ""), new BasicNameValuePair("_lookForSleeper", "on"), new BasicNameValuePair("_directTrains", "on")}; httpPost.setHeader("Host", "ojp.nationalrail.co.uk"); httpPost.setHeader("User-Agent", "Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10_6_4; en-US) AppleWebKit/534.10 (KHTML, like Gecko) Chrome/8.0.552.231 Safari/534.10"); httpPost.setHeader("Accept-Encoding", "gzip,deflate,sdch"); httpPost.setHeader("Accept", "text/html,application/xhtml+xml,application/xml;q=0.9,**/*//*;q=0.8"); httpPost.setHeader("Accept-Language", "en-us,en;q=0.8"); httpPost.setHeader("Accept-Charset", "ISO-8859-1,utf-8;q=0.7,*;q=0.7"); httpPost.setHeader("Origin", "http://www.nationalrail.co.uk/"); httpPost.setHeader("Referer", "http://www.nationalrail.co.uk/"); httpPost.setHeader("Content-Type", "application/x-www-form-urlencoded"); httpPost.setHeader("Cookie", "JSESSIONID=B2A3419B79C5D999CA4806B459675CCD.app201; Path=/"); UrlEncodedFormEntity urlEncodedFormEntity = new UrlEncodedFormEntity(Arrays.asList(params)); urlEncodedFormEntity.setContentEncoding(HTTP.UTF_8); httpPost.setEntity(urlEncodedFormEntity); HttpResponse response = client.execute(httpPost); InputStream input = response.getEntity().getContent(); GZIPInputStream gzip = new GZIPInputStream(input); InputStreamReader isr = new InputStreamReader(gzip); BufferedReader br = new BufferedReader(isr); String line = null; while((line = br.readLine()) != null) { System.out.printf("\n%s", line); } client.getConnectionManager().shutdown(); } } I keep the JSESSION ID updated if it expires but there seems to be another problem that I cannot see. Am I missing something rather obvious? He

  Read the article

• MySQL 5.1.49 freezing every two days

  - by maximus

  Hi all, our mysql system is "freezing" every two days. By "freezing" i mean the following: it doesn't respond to ping we can't login with SSH we don't get any answer from MySQL there is no entry in the error logs! neither from linux neither from MySQL. we have already changed to a completely new hardware, we have the same problem, so it's definitely not a hardware problem. we do not have any other software installed except a firewall (iptables rule) we can restart the server from another server using rsyslog (www.rsyslog.com)(software reset) Could someone help me, by giving me some pointers what could i do to figure out the problem? I have included every detail about our settings. Thank you in advance for your help. Max. Our system parameters and settings: System-Memory: 12GB Processor: Intel 7-920 Quadcore Operating system: Debian 5 (lenny) 64bit MySQL 5.1.49 Databases: (a) a small phpbb forum (b) a 6GB database 3 tables with about 15 million rows my.cnf # # The MySQL database server configuration file. # # You can copy this to one of: # - "/etc/mysql/my.cnf" to set global options, # - "~/.my.cnf" to set user-specific options. # # One can use all long options that the program supports. # Run program with --help to get a list of available options and with # --print-defaults to see which it would actually understand and use. # # For explanations see # http://dev.mysql.com/doc/mysql/en/server-system-variables.html # This will be passed to all mysql clients # It has been reported that passwords should be enclosed with ticks/quotes # escpecially if they contain "#" chars... # Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] # # * Basic Settings # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. bind-address = our-ip-address # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 256K thread_cache_size = 32 max_connections = 300 table_cache = 2048 #thread_concurrency = 4 # Used for InnoDB tables recommended to 50%-80% available memory innodb_buffer_pool_size = 6G # 20MB sometimes larger innodb_additional_mem_pool_size = 20M # 8M-16M is good for most situations innodb_log_buffer_size = 8M # Disable XA support because we do not use it innodb-support-xa = 0 # 1 is default wich is 100% secure but 2 offers better performance innodb_flush_log_at_trx_commit = 1 innodb_flush_method = O_DIRECT #innodb_thread_concurency = 8 # Recommended 64M - 512M depending on server size innodb_log_file_size = 512M # One file per table innodb_file_per_table # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 16M #query_cache_type = 1 #query_cache_min_res_unit= 2K #join_buffer_size = 1M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 # # Error logging goes to syslog. This is a Debian improvement :) # # Here you can see queries with especially long duration log_slow_queries = /var/log/mysql/mysql-slow.log long_query_time = 2 log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. #server-id = 1 log_bin = /var/log/mysql/mysql-bin.log # WARNING: Using expire_logs_days without bin_log crashes the server! See README.Debian! expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # * InnoDB plugin # As of MySQL 5.1.38, the InnoDB plugin from Oracle is included in the MySQL source code. # It has many improvements and better performances than the built-in InnoDB storage engine. # Please read http://www.innodb.com/products/innodb_plugin/ for more information. # Uncommenting the two following lines to use the InnoDB plugin. ignore_builtin_innodb plugin-load=innodb=ha_innodb_plugin.so # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * NDB Cluster # # See /usr/share/doc/mysql-server-*/README.Debian for more information. # # The following configuration is read by the NDB Data Nodes (ndbd processes) # not from the NDB Management Nodes (ndb_mgmd processes). # # [MYSQL_CLUSTER] # ndb-connectstring=127.0.0.1 # # * IMPORTANT: Additional settings that can override those from this file! # !includedir /etc/mysql/conf.d/ UPDATE After installing sysstat and configuring it to collect data after every minute i have the following datas. I used sar to generate the following output: The log-file is too big so coudn't enter it here but uploaded to box.net. The link is http://www.box.net/shared/xc6rh7qqob SECOND UPDATE We started a ping command in the background, and that solved the problem. Now the server does work since more then a week. We still don't know what's the problem.

  Read the article

• wmi not available for some time after reboot

  - by Alex Okrushko

  I'm having the problem with the WMI availability on logon. Right after reboot I open cmd and with python interpreter: >>> import wmi >>> c = wmi.WMI() >>> c.Win32_OperatingSystem() Traceback (most recent call last): File "<stdin>", line 1, in <module> File "C:\Python27\lib\site-packages\wmi.py", line 1147, in __getattr__ return getattr (self._namespace, attribute) File "C:\Python27\lib\site-packages\win32com\client\dynamic.py", line 516, in __getattr__ raise AttributeError("%s.%s" % (self._username_, attr)) AttributeError: winmgmts:.Win32_OperatingSystem >>> 5 minutes later I open another cmd and python interpreter: Python 2.7.3 (default, Apr 10 2012, 23:31:26) [MSC v.1500 32 bit (Intel)] on win 32 Type "help", "copyright", "credits" or "license" for more information. >>> import wmi >>> c = wmi.WMI() >>> c.Win32_OperatingSystem() [<_wmi_object: \\W520-ALEX-WIN7\root\cimv2:Win32_OperatingSystem=@>] >>> NOTE: the first cmd still keeps saying AttributeError even 5 minutes later. NOTE 2: if I logout and login wmi is available, so it is somehow effected by reboot with process explorer I check the environmental variables and they are the same for both cmds What could that be? Please help. UPDATE: Apparently the problem is connecting to the wbem services: >>> import win32com.client >>> win32com.client.Dispatch('WbemScripting.SWbemLocator') <COMObject WbemScripting.SWbemLocator> >>> wmi_service= win32com.client.Dispatch('WbemScripting.SWbemLocator') >>> wbem_service = wmi_service.ConnectServer('.','root/cimv2') >>> wbem_service <COMObject <unknown>> >>> items = wbem_service.ExecQuery('Select * from Win32_OperatingSystem') Traceback (most recent call last): File "<stdin>", line 1, in <module> File "<COMObject <unknown>>", line 3, in ExecQuery File "C:\Python27\lib\site-packages\win32com\client\dynamic.py", line 282, in _ApplyTypes_ result = self._oleobj_.InvokeTypes(*(dispid, LCID, wFlags, retType, argTypes ) + args) pywintypes.com_error: (-2147352567, 'Exception occurred.', (0, u'SWbemServicesEx ', u'Generic failure ', None, 0, -2147217407), None) >>> NOTE 3: wmic os always worked. NOTE 4: re-installing pywin32 package didn't help. Neither did Re-registering/re-compiling the WMI components and resetting of the WMI database (as recommended here) NOTE 5: my 4 Other laptops don't have this problem. Also wmiprov.log has: (Mon Oct 29 11:40:07 2012.248587) : *************************************** (Mon Oct 29 11:40:07 2012.248587) : Could not get pointer to binary resource for file: (Mon Oct 29 11:40:07 2012.248587) : C:\Windows\system32\drivers\ndis.sys[MofResourceName](Mon Oct 29 11:40:07 2012.248587) : (Mon Oct 29 11:40:07 2012.248587) : *************************************** (Mon Oct 29 11:40:07 2012.248587) : *************************************** (Mon Oct 29 11:40:07 2012.248587) : Could not get pointer to binary resource for file: (Mon Oct 29 11:40:07 2012.248587) : C:\Windows\system32\drivers\en-US\ndis.sys.mui[MofResourceName](Mon Oct 29 11:40:07 2012.248587) : (Mon Oct 29 11:40:07 2012.248587) : *************************************** (Mon Oct 29 11:40:07 2012.248603) : *************************************** (Mon Oct 29 11:40:07 2012.248603) : Could not get pointer to binary resource for file: (Mon Oct 29 11:40:07 2012.248603) : C:\Windows\system32\DRIVERS\wmiacpi.sys[MofResource](Mon Oct 29 11:40:07 2012.248603) : (Mon Oct 29 11:40:07 2012.248603) : *************************************** (Mon Oct 29 11:40:07 2012.248603) : *************************************** (Mon Oct 29 11:40:07 2012.248603) : Could not get pointer to binary resource for file: (Mon Oct 29 11:40:07 2012.248603) : C:\Windows\system32\DRIVERS\monitor.sys[MonitorWMI](Mon Oct 29 11:40:07 2012.248603) : (Mon Oct 29 11:40:07 2012.248603) : *************************************** NOTE 6: the WMIDiag tool report is at my dropbox

  Read the article

• Recently "exposed" to Clicksor

  - by I take Drukqs

  Previous information concerning my issue can be found here: Virus...? Tons of people talking. Not sure where else to ask. I heard the loud sounds and whatnot from one of the ads but nothing was harmed and other than having the life scared out of me nothing was immediately affected. Literally nothing has changed. I really don't know what to do. My PC seems fine and from what Malwarebytes and Spybot tells me none of my files have been infected with anything. If you need more information I will be glad to supply it. Thanks in advance. Malwarebytes quick and full scan: Clean. Spybot S&D scan: Clean. HijackThis log: Logfile of Trend Micro HijackThis v2.0.4 Scan saved at 5:23:33 PM, on 2/2/2011 Platform: Windows 7 (WinNT 6.00.3504) MSIE: Internet Explorer v8.00 (8.00.7600.16700) Boot mode: Normal Running processes: C:\Program Files (x86)\DeviceVM\Browser Configuration Utility\BCU.exe C:\Program Files (x86)\NEC Electronics\USB 3.0 Host Controller Driver\Application\nusb3mon.exe C:\Program Files (x86)\Common Files\InstallShield\UpdateService\issch.exe C:\Program Files (x86)\Common Files\Java\Java Update\jusched.exe C:\Program Files (x86)\Pidgin\pidgin.exe C:\Program Files (x86)\Steam\Steam.exe C:\Program Files (x86)\Mozilla Firefox\firefox.exe C:\Program Files (x86)\uTorrent\uTorrent.exe C:\Fraps\fraps.exe C:\Program Files (x86)\Mozilla Firefox\plugin-container.exe C:\Program Files (x86)\Trend Micro\HiJackThis\HiJackThis.exe R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKCU\Software\Microsoft\Internet Explorer\Main,Start Page = http://go.microsoft.com/fwlink/?LinkId=69157 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Page_URL = http://go.microsoft.com/fwlink/?LinkId=69157 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Search_URL = http://go.microsoft.com/fwlink/?LinkId=54896 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKLM\Software\Microsoft\Internet Explorer\Main,Start Page = http://go.microsoft.com/fwlink/?LinkId=69157 R0 - HKLM\Software\Microsoft\Internet Explorer\Search,SearchAssistant = R0 - HKLM\Software\Microsoft\Internet Explorer\Search,CustomizeSearch = R0 - HKLM\Software\Microsoft\Internet Explorer\Main,Local Page = C:\Windows\SysWOW64\blank.htm R0 - HKCU\Software\Microsoft\Internet Explorer\Toolbar,LinksFolderName = R3 - URLSearchHook: SearchHook Class - {BC86E1AB-EDA5-4059-938F-CE307B0C6F0A} - C:\Program Files (x86)\DeviceVM\Browser Configuration Utility\AddressBarSearch.dll F2 - REG:system.ini: UserInit=userinit.exe O2 - BHO: AcroIEHelperStub - {18DF081C-E8AD-4283-A596-FA578C2EBDC3} - C:\Program Files (x86)\Common Files\Adobe\Acrobat\ActiveX\AcroIEHelperShim.dll O2 - BHO: Windows Live ID Sign-in Helper - {9030D464-4C02-4ABF-8ECC-5164760863C6} - C:\Program Files (x86)\Common Files\Microsoft Shared\Windows Live\WindowsLiveLogin.dll O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files (x86)\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [BCU] "C:\Program Files (x86)\DeviceVM\Browser Configuration Utility\BCU.exe" O4 - HKLM\..\Run: [JMB36X IDE Setup] C:\Windows\RaidTool\xInsIDE.exe O4 - HKLM\..\Run: [NUSB3MON] "C:\Program Files (x86)\NEC Electronics\USB 3.0 Host Controller Driver\Application\nusb3mon.exe" O4 - HKLM\..\Run: [ISUSScheduler] "C:\Program Files (x86)\Common Files\InstallShield\UpdateService\issch.exe" -start O4 - HKLM\..\Run: [ISUSPM Startup] C:\PROGRA~2\COMMON~1\INSTAL~1\UPDATE~1\ISUSPM.exe -startup O4 - HKLM\..\Run: [Adobe Reader Speed Launcher] "C:\Program Files (x86)\Adobe\Reader 10.0\Reader\Reader_sl.exe" O4 - HKLM\..\Run: [Adobe ARM] "C:\Program Files (x86)\Common Files\Adobe\ARM\1.0\AdobeARM.exe" O4 - HKLM\..\Run: [SunJavaUpdateSched] "C:\Program Files (x86)\Common Files\Java\Java Update\jusched.exe" O4 - HKLM\..\RunOnce: [Malwarebytes' Anti-Malware] C:\Program Files (x86)\Malwarebytes' Anti-Malware\mbamgui.exe /install /silent O4 - HKCU\..\Run: [ISUSPM Startup] C:\PROGRA~2\COMMON~1\INSTAL~1\UPDATE~1\ISUSPM.exe -startup O4 - HKUS\S-1-5-19\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-19\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-20\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'NETWORK SERVICE') O4 - HKUS\S-1-5-20\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'NETWORK SERVICE') O10 - Unknown file in Winsock LSP: c:\program files (x86)\common files\microsoft shared\windows live\wlidnsp.dll O10 - Unknown file in Winsock LSP: c:\program files (x86)\common files\microsoft shared\windows live\wlidnsp.dll O23 - Service: @%SystemRoot%\system32\Alg.exe,-112 (ALG) - Unknown owner - C:\Windows\System32\alg.exe (file missing) O23 - Service: AppleChargerSrv - Unknown owner - C:\Windows\system32\AppleChargerSrv.exe (file missing) O23 - Service: Browser Configuration Utility Service (BCUService) - DeviceVM, Inc. - C:\Program Files (x86)\DeviceVM\Browser Configuration Utility\BCUService.exe O23 - Service: DES2 Service for Energy Saving. (DES2 Service) - Unknown owner - C:\Program Files (x86)\GIGABYTE\EnergySaver2\des2svr.exe O23 - Service: @%SystemRoot%\system32\efssvc.dll,-100 (EFS) - Unknown owner - C:\Windows\System32\lsass.exe (file missing) O23 - Service: @%systemroot%\system32\fxsresm.dll,-118 (Fax) - Unknown owner - C:\Windows\system32\fxssvc.exe (file missing) O23 - Service: InstallDriver Table Manager (IDriverT) - Macrovision Corporation - C:\Program Files (x86)\Common Files\InstallShield\Driver\11\Intel 32\IDriverT.exe O23 - Service: JMB36X - Unknown owner - C:\Windows\SysWOW64\XSrvSetup.exe O23 - Service: @keyiso.dll,-100 (KeyIso) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @comres.dll,-2797 (MSDTC) - Unknown owner - C:\Windows\System32\msdtc.exe (file missing) O23 - Service: @%SystemRoot%\System32\netlogon.dll,-102 (Netlogon) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: NVIDIA Driver Helper Service (NVSvc) - Unknown owner - C:\Windows\system32\nvvsvc.exe (file missing) O23 - Service: @%systemroot%\system32\psbase.dll,-300 (ProtectedStorage) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%systemroot%\system32\Locator.exe,-2 (RpcLocator) - Unknown owner - C:\Windows\system32\locator.exe (file missing) O23 - Service: @%SystemRoot%\system32\samsrv.dll,-1 (SamSs) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%SystemRoot%\system32\snmptrap.exe,-3 (SNMPTRAP) - Unknown owner - C:\Windows\System32\snmptrap.exe (file missing) O23 - Service: @%systemroot%\system32\spoolsv.exe,-1 (Spooler) - Unknown owner - C:\Windows\System32\spoolsv.exe (file missing) O23 - Service: @%SystemRoot%\system32\sppsvc.exe,-101 (sppsvc) - Unknown owner - C:\Windows\system32\sppsvc.exe (file missing) O23 - Service: Steam Client Service - Valve Corporation - C:\Program Files (x86)\Common Files\Steam\SteamService.exe O23 - Service: NVIDIA Stereoscopic 3D Driver Service (Stereo Service) - NVIDIA Corporation - C:\Program Files (x86)\NVIDIA Corporation\3D Vision\nvSCPAPISvr.exe O23 - Service: @%SystemRoot%\system32\ui0detect.exe,-101 (UI0Detect) - Unknown owner - C:\Windows\system32\UI0Detect.exe (file missing) O23 - Service: @%SystemRoot%\system32\vaultsvc.dll,-1003 (VaultSvc) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%SystemRoot%\system32\vds.exe,-100 (vds) - Unknown owner - C:\Windows\System32\vds.exe (file missing) O23 - Service: @%systemroot%\system32\vssvc.exe,-102 (VSS) - Unknown owner - C:\Windows\system32\vssvc.exe (file missing) O23 - Service: @%SystemRoot%\system32\Wat\WatUX.exe,-601 (WatAdminSvc) - Unknown owner - C:\Windows\system32\Wat\WatAdminSvc.exe (file missing) O23 - Service: @%systemroot%\system32\wbengine.exe,-104 (wbengine) - Unknown owner - C:\Windows\system32\wbengine.exe (file missing) O23 - Service: @%Systemroot%\system32\wbem\wmiapsrv.exe,-110 (wmiApSrv) - Unknown owner - C:\Windows\system32\wbem\WmiApSrv.exe (file missing) O23 - Service: @%PROGRAMFILES%\Windows Media Player\wmpnetwk.exe,-101 (WMPNetworkSvc) - Unknown owner - C:\Program Files (x86)\Windows Media Player\wmpnetwk.exe (file missing) -- End of file - 7889 bytes

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• Gateway setting is empty

  - by Dodi Jones

  This laptop hasn't been used in almost a year. It connected to the internet just fine last time used. Now it can't get on line. ipconfig:The Gateway setting for this computer is empty. Make sure your access point is working properly. Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:\Documents and Settings\Dodi>IPCONFIG /ALL Windows IP Configuration Host Name . . . . . . . . . . . . : 8A287A4ADEF0487 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : Yes WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : LAN-Express AS IEEE 802.11g miniPCI Adapter Physical Address. . . . . . . . . : 00-14-A4-72-37-E1 Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.0.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.1.1 Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Intel(R) PRO/100 VE Network Connection Physical Address. . . . . . . . . : 00-01-4A-EF-A8-7D How do I fix this?

  Read the article

• Why do we need different CPU architecture for server & mini/mainframe & mixed-core?

  - by claws

  Hello, I was just wondering what other CPU architectures are available other than INTEL & AMD. So, found List of CPU architectures on Wikipedia. It categorizes notable CPU architectures into following categories. Embedded CPU architectures Microcomputer CPU architectures Workstation/Server CPU architectures Mini/Mainframe CPU architectures Mixed core CPU architectures I was analyzing the purposes and have few doubts. I taking Microcomputer CPU (PC) architecture as reference and comparing others. Embedded CPU architecture: They are a completely new world. Embedded systems are small & do very specific task mostly real time & low power consuming so we do not need so many & such wide registers available in a microcomputer CPU (typical PC). In other words we do need a new small & tiny architecture. Hence new architecture & new instruction RISC. The above point also clarifies why do we need a separate operating system (RTOS). Workstation/Server CPU architectures I don't know what is a workstation. Someone clarify regarding the workstation. As of the server. It is dedicated to run a specific software (server software like httpd, mysql etc.). Even if other processes run we need to give server process priority therefore there is a need for new scheduling scheme and thus we need operating system different than general purpose one. If you have any more points for the need of server OS please mention. But I don't get why do we need a new CPU Architecture. Why cant Microcomputer CPU architecture do the job. Can someone please clarify? Mini/Mainframe CPU architectures Again I don't know what are these & what miniframes or mainframes used for? I just know they are very big and occupy complete floor. But I never read about some real world problems they are trying to solve. If any one working on one of these. Share your knowledge. Can some one clarify its purpose & why is it that microcomputer CPU archicture not suitable for it? Is there a new kind of operating system for this too? Why? Mixed core CPU architectures Never heard of these. If possible please keep your answer in this format: XYZ CPU architectures Purpose of XYZ Need for a new architecture. why can't current microcomputer CPU architecture work? They go upto 3GHZ & have upto 8 cores. Need for a new Operating System Why do we need a new kind of operating system for this kind of archictures?

  Read the article

• Why are there 3 conflicting OpenCV camera calibration formulas?

  - by John

  I'm having a problem with OpenCV's various parameterization of coordinates used for camera calibration purposes. The problem is that three different sources of information on image distortion formulae apparently give three non-equivalent description of the parameters and equations involved: (1) In their book "Learning OpenCV…" Bradski and Kaehler write regarding lens distortion (page 376): xcorrected = x * ( 1 + k1 * r^2 + k2 * r^4 + k3 * r^6 ) + [ 2 * p1 * x * y + p2 * ( r^2 + 2 * x^2 ) ], ycorrected = y * ( 1 + k1 * r^2 + k2 * r^4 + k3 * r^6 ) + [ p1 * ( r^2 + 2 * y^2 ) + 2 * p2 * x * y ], where r = sqrt( x^2 + y^2 ). Assumably, (x, y) are the coordinates of pixels in the uncorrected captured image corresponding to world-point objects with coordinates (X, Y, Z), camera-frame referenced, for which xcorrected = fx * ( X / Z ) + cx and ycorrected = fy * ( Y / Z ) + cy, where fx, fy, cx, and cy, are the camera's intrinsic parameters. So, having (x, y) from a captured image, we can obtain the desired coordinates ( xcorrected, ycorrected ) to produced an undistorted image of the captured world scene by applying the above first two correction expressions. However... (2) The complication arises as we look at OpenCV 2.0 C Reference entry under the Camera Calibration and 3D Reconstruction section. For ease of comparison we start with all world-point (X, Y, Z) coordinates being expressed with respect to the camera's reference frame, just as in #1. Consequently, the transformation matrix [ R | t ] is of no concern. In the C reference, it is expressed that: x' = X / Z, y' = Y / Z, x'' = x' * ( 1 + k1 * r'^2 + k2 * r'^4 + k3 * r'^6 ) + [ 2 * p1 * x' * y' + p2 * ( r'^2 + 2 * x'^2 ) ], y'' = y' * ( 1 + k1 * r'^2 + k2 * r'^4 + k3 * r'^6 ) + [ p1 * ( r'^2 + 2 * y'^2 ) + 2 * p2 * x' * y' ], where r' = sqrt( x'^2 + y'^2 ), and finally that u = fx * x'' + cx, v = fy * y'' + cy. As one can see these expressions are not equivalent to those presented in #1, with the result that the two sets of corrected coordinates ( xcorrected, ycorrected ) and ( u, v ) are not the same. Why the contradiction? It seems to me the first set makes more sense as I can attach physical meaning to each and every x and y in there, while I find no physical meaning in x' = X / Z and y' = Y / Z when the camera focal length is not exactly 1. Furthermore, one cannot compute x' and y' for we don't know (X, Y, Z). (3) Unfortunately, things get even murkier when we refer to the writings in Intel's Open Source Computer Vision Library Reference Manual's section Lens Distortion (page 6-4), which states in part: "Let ( u, v ) be true pixel image coordinates, that is, coordinates with ideal projection, and ( u ~, v ~ ) be corresponding real observed (distorted) image coordinates. Similarly, ( x, y ) are ideal (distortion-free) and ( x ~, y ~ ) are real (distorted) image physical coordinates. Taking into account two expansion terms gives the following: x ~ = x * ( 1 + k1 * r^2 + k2 * r^4 ) + [ 2 p1 * x * y + p2 * ( r^2 + 2 * x^2 ) ] y ~ = y * ( 1 + k1 * r^2 + k2 * r^4 ] + [ 2 p2 * x * y + p2 * ( r^2 + 2 * y^2 ) ], where r = sqrt( x^2 + y^2 ). ... "Because u ~ = cx + fx * u and v ~ = cy + fy * v , … the resultant system can be rewritten as follows: u ~ = u + ( u – cx ) * [ k1 * r^2 + k2 * r^4 + 2 * p1 * y + p2 * ( r^2 / x + 2 * x ) ] v ~ = v + ( v – cy ) * [ k1 * r^2 + k2 * r^4 + 2 * p2 * x + p1 * ( r^2 / y + 2 * y ) ] The latter relations are used to undistort images from the camera." Well, it would appear that the expressions involving x ~ and y ~ coincided with the two expressions given at the top of this writing involving xcorrected and ycorrected. However, x ~ and y ~ do not refer to corrected coordinates, according to the given description. I don't understand the distinction between the meaning of the coordinates ( x ~, y ~ ) and ( u ~, v ~ ), or for that matter, between the pairs ( x, y ) and ( u, v ). From their descriptions it appears their only distinction is that ( x ~, y ~ ) and ( x, y ) refer to 'physical' coordinates while ( u ~, v ~ ) and ( u, v ) do not. What is this distinction all about? Aren't they all physical coordinates? I'm lost! Thanks for any input!

  Read the article

• nginx+php-fpm help optimize configs

  - by Dmitro

  I have 3 servers. First server (CPU - model name: 06/17, 2.66GHz, 4 cores, 8GB RAM) have nginx as load balancer with next config upstream lb_mydomain { server mydomain.ru:81 weight=2; server 66.0.0.18 weight=6; } server { listen 80; server_name ~(?!mydomain.ru)(.*); client_max_body_size 20m; location / { proxy_pass http://lb_mydomain; proxy_redirect off; proxy_set_header Connection close; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass_header Set-Cookie; proxy_pass_header P3P; proxy_pass_header Content-Type; proxy_pass_header Content-Disposition; proxy_pass_header Content-Length; } } And configs from nginx.conf: user www-data; worker_processes 5; # worker_priority -1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 5024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; default_type application/octet-stream; #tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; # PHP-FPM (backend) upstream php-fpm { server 127.0.0.1:9000; } include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } And config php-fpm: listen = 127.0.0.1:9000 ;listen.backlog = -1 ;listen.allowed_clients = 127.0.0.1 ;listen.owner = www-data ;listen.group = www-data ;listen.mode = 0666 user = www-data group = www-data pm = dynamic pm.max_children = 80 ;pm.start_servers = 20 pm.min_spare_servers = 5 pm.max_spare_servers = 35 ;pm.max_requests = 500 pm.status_path = /status ping.path = /ping ;ping.response = pong request_terminate_timeout = 30s request_slowlog_timeout = 10s slowlog = /var/log/php-fpm.log.slow ;rlimit_files = 1024 ;rlimit_core = 0 ;chroot = chdir = /var/www ;catch_workers_output = yes ;env[HOSTNAME] = $HOSTNAME ;env[PATH] = /usr/local/bin:/usr/bin:/bin ;env[TMP] = /tmp ;env[TMPDIR] = /tmp ;env[TEMP] = /tmp ;php_admin_value[sendmail_path] = /usr/sbin/sendmail -t -i -f [email protected] ;php_flag[display_errors] = off ;php_admin_value[error_log] = /var/log/fpm-php.www.log ;php_admin_flag[log_errors] = on ;php_admin_value[memory_limit] = 32M In top I see 20 php-fpm processes which use from 1% - 15% CPU. So it's have high load averadge: top - 15:36:22 up 34 days, 20:54, 1 user, load average: 5.98, 7.75, 8.78 Tasks: 218 total, 1 running, 217 sleeping, 0 stopped, 0 zombie Cpu(s): 34.1%us, 3.2%sy, 0.0%ni, 37.0%id, 24.8%wa, 0.0%hi, 0.9%si, 0.0%st Mem: 8183228k total, 7538584k used, 644644k free, 351136k buffers Swap: 9936892k total, 14636k used, 9922256k free, 990540k cached Second server(CPU - model name: Intel(R) Xeon(R) CPU E5504 @ 2.00GHz, 8 cores, 8GB RAM). Nginx configs from nginx.conf: user www-data; worker_processes 5; # worker_priority -1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 5024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; default_type application/octet-stream; #tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; # PHP-FPM (backend) upstream php-fpm { server 127.0.0.1:9000; } include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } And config of php-fpm: listen = 127.0.0.1:9000 ;listen.backlog = -1 ;listen.allowed_clients = 127.0.0.1 ;listen.owner = www-data ;listen.group = www-data ;listen.mode = 0666 user = www-data group = www-data pm = dynamic pm.max_children = 50 ;pm.start_servers = 20 pm.min_spare_servers = 5 pm.max_spare_servers = 35 ;pm.max_requests = 500 ;pm.status_path = /status ;ping.path = /ping ;ping.response = pong ;request_terminate_timeout = 0 ;request_slowlog_timeout = 0 ;slowlog = /var/log/php-fpm.log.slow ;rlimit_files = 1024 ;rlimit_core = 0 ;chroot = chdir = /var/www ;catch_workers_output = yes ;env[HOSTNAME] = $HOSTNAME ;env[PATH] = /usr/local/bin:/usr/bin:/bin ;env[TMP] = /tmp ;env[TMPDIR] = /tmp ;env[TEMP] = /tmp ;php_admin_value[sendmail_path] = /usr/sbin/sendmail -t -i -f [email protected] ;php_flag[display_errors] = off ;php_admin_value[error_log] = /var/log/fpm-php.www.log ;php_admin_flag[log_errors] = on ;php_admin_value[memory_limit] = 32M In top I see 50 php-fpm processes which use from 10% - 25% CPU. So it's have high load averadge: top - 15:53:05 up 33 days, 1:15, 1 user, load average: 41.35, 40.28, 39.61 Tasks: 239 total, 40 running, 199 sleeping, 0 stopped, 0 zombie Cpu(s): 96.5%us, 3.1%sy, 0.0%ni, 0.0%id, 0.0%wa, 0.0%hi, 0.4%si, 0.0%st Mem: 8185560k total, 7804224k used, 381336k free, 161648k buffers Swap: 19802108k total, 16k used, 19802092k free, 5068112k cached Third server is server with database postgresql. Also i try ab -n 50 -c 5 http://www.mydomain.ru/ And I get next info: Complete requests: 50 Failed requests: 48 (Connect: 0, Receive: 0, Length: 48, Exceptions: 0) Write errors: 0 Total transferred: 9271367 bytes HTML transferred: 9247767 bytes Requests per second: 1.02 [#/sec] (mean) Time per request: 4882.427 [ms] (mean) Time per request: 976.486 [ms] (mean, across all concurrent requests) Transfer rate: 185.44 [Kbytes/sec] received Please advise how can I make lower level of load average?

  Read the article

• Why are my USB 2.0 devices hanging Windows XP?

  - by BenAlabaster

  Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a DFI CM33-TL/G ATX (identified using SiSoft Sandra) motherboard hosting an Intel Celeron 1.3GHz CPU, 768Mb PC133 SDRAM, a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board based on the NEC uPD720102 chipset containing 3 external and 1 internal USB sockets. It's also hosting a 1.44Mb floppy drive on FDD0, a new 80Gb Western Digital hard drive running as master on IDE0 and a Panasonic DVD+/-RW running as master on IDE1. All this is sitting in a slimline case running off a Macron Power MPT-135 135W Flex power supply. The motherboard is running a version of Award BIOS 05/24/2002-601T-686B-6A6LID4AC-00. Could this be updated? If so, from where? I've raked through the manufacturer's website but can't find any hint of downloads for either drivers or BIOS updates. The hard disk is freshly formatted and built with Windows XP Professional/Service Pack 3 and is up to date with all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 hangs the whole machine as soon as it starts up, requiring a hard boot to recover). It's got a Daytek MV150 15" touch screen hooked up to the on board VGA and COM1 sockets with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem: If I hook any devices to the USB 2.0 sockets, it hangs the whole machine and I have to hard boot it to get it back up. If I have any devices attached to the USB 2.0 sockets when I boot up, it hangs before Windows gets to the login prompt and I have to hard boot it to recover. Workarounds found: I can plug the same devices into the on board USB 1.0 sockets and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions: I've seen suggestions that this could be a power problem - that the PSU just doesn't have the wattage to drive these ports. While I'm doubtful this is the problem [after all the motherboard has the same standard connector regardless of the PSU wattage], I tried disabling all the on board devices that I'm not using - on board LAN, the second COM port, the AGP connector etc. through the BIOS in what I'm sure is a futile attempt to reduce the power consumption... I also modified the ACPI and power management settings. It didn't have any noticeable affect, although it didn't do any harm either. Could the wattage of the PSU really cause this problem? If it can, is there anything I need to be aware of when replacing it or do I just need to make sure it's got a higher wattage than the current one? My interpretation was that the wattage only affected the number of drives you could hook up to the power connectors, is that right? I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself, and Windows says the card is installed and working correctly... right up until I connect a device to it. The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference - does anyone have any experience that would suggest this might work? Other thoughts/questions: Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question: Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

  Read the article

• GLSL Error: failed to preprocess the source. How can I troubleshoot this?

  - by Brent Parker

  I'm trying to learn to play with OpenGL GLSL shaders. I've written a very simple program to simply create a shader and compile it. However, whenever I get to the compile step, I get the error: Error: Preprocessor error Error: failed to preprocess the source. Here's my very simple code: #include <GL/gl.h> #include <GL/glu.h> #include <GL/glut.h> #include <GL/glext.h> #include <time.h> #include <stdio.h> #include <iostream> #include <stdlib.h> using namespace std; const int screenWidth = 640; const int screenHeight = 480; const GLchar* gravity_shader[] = { "#version 140" "uniform float t;" "uniform mat4 MVP;" "in vec4 pos;" "in vec4 vel;" "const vec4 g = vec4(0.0, 0.0, -9.80, 0.0);" "void main() {" " vec4 position = pos;" " position += t*vel + t*t*g;" " gl_Position = MVP * position;" "}" }; double pointX = (double)screenWidth/2.0; double pointY = (double)screenWidth/2.0; void initShader() { GLuint shader = glCreateShader(GL_VERTEX_SHADER); glShaderSource(shader, 1, gravity_shader, NULL); glCompileShader(shader); GLint compiled = true; glGetShaderiv(shader, GL_COMPILE_STATUS, &compiled); if(!compiled) { GLint length; GLchar* log; glGetShaderiv(shader, GL_INFO_LOG_LENGTH, &length); log = (GLchar*)malloc(length); glGetShaderInfoLog(shader, length, &length, log); std::cout << log <<std::endl; free(log); } exit(0); } bool myInit() { initShader(); glClearColor(1.0f, 1.0f, 1.0f, 0.0f); glColor3f(0.0f, 0.0f, 0.0f); glPointSize(1.0); glLineWidth(1.0f); glMatrixMode(GL_PROJECTION); glLoadIdentity(); gluOrtho2D(0.0, (GLdouble) screenWidth, 0.0, (GLdouble) screenHeight); glEnable(GL_DEPTH_TEST); return true; } int main(int argc, char** argv) { glutInit(&argc, argv); glutInitDisplayMode(GLUT_DOUBLE | GLUT_RGB); glutInitWindowSize(screenWidth, screenHeight); glutInitWindowPosition(100, 150); glutCreateWindow("Mouse Interaction Display"); myInit(); glutMainLoop(); return 0; } Where am I going wrong? If it helps, I am trying to do this on a Acer Aspire One with an atom processor and integrated Intel video running the latest Ubuntu. It's not very powerful, but then again, this is a very simple shader. Thanks a lot for taking a look!

  Read the article

• With dnsmasq as the DNS server, 'dig' and 'ping' succeed while 'nslookup' fails

  - by einpoklum

  I installed dnsmasq on a machine of mine (It's a Kubuntu 12.04 LTS), backed only by /etc/hosts (no connection to the Internet until later). Now, if I dig mymachine, I get 192.168.0.1, but if I try to nslookup mymachine, I get: >> connection timed out; no servers could be reached Tried also nslookup mymachine.mynicedomain.org - didn't work either. pinging (Edit:) succeeds. This happens both on the server machine itself and on other machines on the network. How can I the DNS lookups to work? What problem is preventing nslookup from succeeding? Additional Information In the server's /etc/hosts: 192.168.0.1 mymachine In the server's nsswitch.conf: hosts: files mdns4_mininal [NOTFOUND=return] dns mdns4 (admittedly, this is a bit weird; but I also tried: hosts: files dns instead, with the same effect) In resolv.conf (which is generated by dnsmasq): nameserver 127.0.0.1 search mynicedomain.org In the server's /etc/hosts.allow: domain: ALL In the other machines' /etc/resolv.conf (this is set by the DHCP client): nameserver 192.168.0.1 search mynicedomain.org Relevant netstat output on the server: Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:53 0.0.0.0:* LISTEN tcp 0 0 192.168.0.1:53 0.0.0.0:* LISTEN Finally, here's the ipconfig output from one of the client machines on the network (running Windows 7): Connection-specific DNS Suffix . : mynicedomain.org Description . . . . . . . . . . . : Intel(R) 82579LM Gigabit Network Connection Physical Address. . . . . . . . . : 12-34-56-78-9A-BC DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.50(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Sunday, October 20th 2013 16:20:25 Lease Expires . . . . . . . . . . : Sunday, October 20th 2013 18:20:24 Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled Notes: May be related to this question.

  Read the article

• NMap route determination on Windows 7 x64

  - by user30772

  C:\Windows\system32>nmap --iflist Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 06:51 Central Daylight Time ************************INTERFACES************************ DEV (SHORT) IP/MASK TYPE UP MTU MAC eth0 (eth0) fe80::797f:b9b6:3ee0:27b8/64 ethernet down 1500 5C:AC:4C:E9:2D:46 eth0 (eth0) 169.254.39.184/4 ethernet down 1500 5C:AC:4C:E9:2D:46 eth1 (eth1) fe80::5c02:7e48:8fbe:c7c9/64 ethernet down 1500 00:FF:3F:7C:7C:2B eth1 (eth1) 169.254.199.201/4 ethernet down 1500 00:FF:3F:7C:7C:2B eth2 (eth2) fe80::74e4:1ab7:1b7d:a0d0/64 ethernet up 1500 14:FE:B5:BA:8A:C3 eth2 (eth2) 10.0.0.0.253/24 ethernet up 1500 14:FE:B5:BA:8A:C3 eth3 (eth3) fe80::b03e:ddf5:bb5c:5f76/64 ethernet up 1500 00:50:56:C0:00:01 eth3 (eth3) 169.254.95.118/16 ethernet up 1500 00:50:56:C0:00:01 eth4 (eth4) fe80::b175:831d:e60:27b/64 ethernet up 1500 00:50:56:C0:00:08 eth4 (eth4) 192.168.153.1/24 ethernet up 1500 00:50:56:C0:00:08 lo0 (lo0) ::1/128 loopback up -1 lo0 (lo0) 127.0.0.1/8 loopback up -1 tun0 (tun0) fe80::100:7f:fffe/64 point2point down 1280 tun1 (tun1) (null)/0 point2point down 1280 tun2 (tun2) fe80::5efe:a9fe:5f76/128 point2point down 1280 tun3 (tun3) (null)/0 point2point down 1280 tun4 (tun4) fe80::5efe:c0a8:9901/128 point2point down 1280 tun5 (tun5) fe80::5efe:ac14:fd/128 point2point down 1280 DEV WINDEVICE eth0 \Device\NPF_{0024872A-5A41-42DF-B484-FB3D3ED3FCE9} eth0 \Device\NPF_{0024872A-5A41-42DF-B484-FB3D3ED3FCE9} eth1 \Device\NPF_{3F7C7C2B-9AF3-45BB-B96E-2F00143CC2F7} eth1 \Device\NPF_{3F7C7C2B-9AF3-45BB-B96E-2F00143CC2F7} eth2 \Device\NPF_{08116FE5-F0FF-498A-9BF1-515528C57C13} eth2 \Device\NPF_{08116FE5-F0FF-498A-9BF1-515528C57C13} eth3 \Device\NPF_{AA83C6CE-AB2E-4764-92D1-CDEAFBA7AD21} eth3 \Device\NPF_{AA83C6CE-AB2E-4764-92D1-CDEAFBA7AD21} eth4 \Device\NPF_{D0679889-E9D4-411D-BDC5-F4DDB758E151} eth4 \Device\NPF_{D0679889-E9D4-411D-BDC5-F4DDB758E151} lo0 <none> lo0 <none> tun0 <none> tun1 <none> tun2 <none> tun3 <none> tun4 <none> tun5 <none> **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.153.255/32 eth0 255.255.255.255/32 eth0 255.255.255.255/32 eth0 127.0.0.1/32 eth0 127.255.255.255/32 eth0 255.255.255.255/32 eth0 169.254.95.118/32 eth0 169.254.255.255/32 eth0 10.0.0.0.253/32 eth0 255.255.255.255/32 eth0 10.0.0.0.255/32 eth0 255.255.255.255/32 eth0 192.168.153.1/32 eth0 255.255.255.255/32 eth0 10.0.0.0.0/24 eth0 192.168.153.0/24 eth0 10.10.10.0/24 eth0 10.0.0.0.4 169.254.0.0/16 eth0 127.0.0.0/8 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 0.0.0.0/0 eth0 10.0.0.0.1 JMeterX - I worded that way in hopes of raising answer efficnecy, but that probably wasnt the smartest choice. IMHO the problem (could be a symptom) is that nmap retardedly chooses eth0 as the gateway interface for any and all networks. Here's the result: C:\Windows\system32>nmap 10.0.0.55 Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 07:43 Central Daylight Time Note: Host seems down. If it is really up, but blocking our ping probes, try -Pn Nmap done: 1 IP address (0 hosts up) scanned in 0.95 seconds C:\Windows\system32>nmap -e eth2 10.0.0.55 Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 07:44 Central Daylight Time Nmap scan report for esxy5.dionne.net (10.0.0.55) Host is up (0.00070s latency). Not shown: 991 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 427/tcp open svrloc 443/tcp open https 902/tcp open iss-realsecure 5988/tcp closed wbem-http 5989/tcp open wbem-https 8000/tcp open http-alt 8100/tcp open xprint-server MAC Address: 00:1F:29:59:C7:03 (Hewlett-Packard Company) Nmap done: 1 IP address (1 host up) scanned in 5.29 seconds Just to be clear, this is what makes absolutly no sense to me whatsoever. For reference, I've included similar info from an Ubuntu (that works normally) vm on the affected host below. Jacked Windows 7 **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.153.255/32 eth0 255.255.255.255/32 eth0 255.255.255.255/32 eth0 127.0.0.1/32 eth0 127.255.255.255/32 eth0 255.255.255.255/32 eth0 169.254.95.118/32 eth0 169.254.255.255/32 eth0 10.0.0.0.253/32 eth0 255.255.255.255/32 eth0 10.0.0.0.255/32 eth0 255.255.255.255/32 eth0 192.168.153.1/32 eth0 255.255.255.255/32 eth0 10.0.0.0.0/24 eth0 192.168.153.0/24 eth0 10.10.10.0/24 eth0 10.0.0.0.4 169.254.0.0/16 eth0 127.0.0.0/8 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 0.0.0.0/0 eth0 10.0.0.0.1 Working Ubuntu VM root@ubuntu:~# nmap --iflist Starting Nmap 5.21 ( http://nmap.org ) at 2012-08-31 07:44 PDT ************************INTERFACES************************ DEV (SHORT) IP/MASK TYPE UP MAC lo (lo) 127.0.0.1/8 loopback up eth0 (eth0) 172.20.0.89/24 ethernet up 00:0C:29:0A:C9:35 eth1 (eth1) 192.168.225.128/24 ethernet up 00:0C:29:0A:C9:3F eth2 (eth2) 192.168.150.128/24 ethernet up 00:0C:29:0A:C9:49 **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.225.0/0 eth1 192.168.150.0/0 eth2 172.20.0.0/0 eth0 169.254.0.0/0 eth0 0.0.0.0/0 eth0 172.20.0.1 root@ubuntu:~# nmap esxy2 Starting Nmap 5.21 ( http://nmap.org ) at 2012-08-31 07:44 PDT Nmap scan report for esxy2 (172.20.0.52) Host is up (0.00036s latency). rDNS record for 172.20.0.52: esxy2.dionne.net Not shown: 994 filtered ports PORT STATE SERVICE 80/tcp open http 427/tcp closed svrloc 443/tcp open https 902/tcp closed iss-realsecure 8000/tcp open http-alt 8100/tcp open unknown MAC Address: 00:04:23:B1:FA:6A (Intel) Nmap done: 1 IP address (1 host up) scanned in 4.76 seconds

  Read the article

• With dnsmasq as the DNS server, 'dig' succeeds, but 'nslookup' and 'ping' fail

  - by einpoklum

  I installed dnsmasq on a machine of mine (It's a Kubuntu 12.04 LTS), backed only by /etc/hosts (no connection to the Internet until later). Now, when I'm on the same machine as the dnsmasq - or any other machine on the server, I can dig mymachine and get 192.168.0.1, but if I try to nslookup mymachine, I get: >> connection timed out; no servers could be reached Tried also nslookup mymachine.mynicedomain.org - didn't work either. pinging fails. How can I the DNS lookups to work? Is the problem with the nsswitch entries? The dnsmasq configuration? Additional Information In the server's /etc/hosts: 192.168.0.1 mymachine In the server's nsswitch.conf: hosts: files mdns4_mininal [NOTFOUND=return] dns mdns4 (admittedly, this is a bit weird) In resolv.conf (which is generated by dnsmasq): nameserver 127.0.0.1 search mynicedomain.org In the server's /etc/hosts.allow: domain: ALL In the other machines' /etc/resolv.conf (this is set by the DHCP client): nameserver 192.168.0.1 search mynicedomain.org Finally, here's the ipconfig output from one of the client machines on the network (running Windows 7): Connection-specific DNS Suffix . : mynicedomain.org Description . . . . . . . . . . . : Intel(R) 82579LM Gigabit Network Connection Physical Address. . . . . . . . . : 12-34-56-78-9A-BC DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.50(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Sunday, October 20th 2013 16:20:25 Lease Expires . . . . . . . . . . : Sunday, October 20th 2013 18:20:24 Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled Notes: May be related to this question.

  Read the article

• Large concurrent user performance issues for Apache + mod_jk + GlassFish v3.1 clusters

  - by user10035

  I am running a java ee 6 ear application on a GlassFish v3.1 ( 2 clusters with 2 instances each) load balanced by an Apache v2.2 with mod_jk - all on the same server (Windows Server 2003 R2, Intel Xeon CPU x5670 @2.93Ghz, 6GB RAM, 2 cpus). The web application is accessed by around ~100 users. When they all try to access it at the same time every morning ~8am, the response is very slow while trying to access the main jsf home page. Apart from that I have seen the CPU usage spike upto 99% by the httpd process during the day frequently and I start seeing errors in the mod_jk.log file. [Wed Jun 08 08:25:43 2011] [9380:8216] [info] ajp_process_callback::jk_ajp_common.c (1885): Writing to client aborted or client network problems [Wed Jun 08 08:25:43 2011] [9380:8216] [info] ajp_service::jk_ajp_common.c (2543): (myAppLocalInstance4) sending request to tomcat failed (unrecoverable), because of client write error (attempt=1) Any suggestions on how I can go about improving this? Apache configuration is mostly the default as shown below ServerRoot "C:/Program Files/Apache Software Foundation/Apache2.2" Listen 80 LoadModule actions_module modules/mod_actions.so LoadModule alias_module modules/mod_alias.so LoadModule asis_module modules/mod_asis.so LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule cgi_module modules/mod_cgi.so LoadModule dir_module modules/mod_dir.so LoadModule env_module modules/mod_env.so LoadModule include_module modules/mod_include.so LoadModule isapi_module modules/mod_isapi.so LoadModule log_config_module modules/mod_log_config.so LoadModule mime_module modules/mod_mime.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule setenvif_module modules/mod_setenvif.so <IfModule !mpm_netware_module> <IfModule !mpm_winnt_module> User daemon Group daemon </IfModule> </IfModule> DocumentRoot "C:/Program Files/Apache Software Foundation/Apache2.2/htdocs" <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Deny from all </Directory> <Directory "C:/Program Files/Apache Software Foundation/Apache2.2/htdocs"> Options Indexes FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> <IfModule dir_module> DirectoryIndex index.html </IfModule> <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> ErrorLog "logs/error.log" LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog "logs/access.log" common </IfModule> <IfModule alias_module> ScriptAlias /cgi-bin/ "C:/Program Files/Apache Software Foundation/Apache2.2/cgi-bin/" </IfModule> <Directory "C:/Program Files/Apache Software Foundation/Apache2.2/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig conf/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz </IfModule> Include conf/extra/httpd-mpm.conf <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> LoadModule jk_module modules/mod_jk.so JkWorkersFile conf/workers.properties JkLogFile logs/mod_jk.log JkLogLevel info JkLogStampFormat "[%a %b %d %H:%M:%S %Y] " JkOptions +ForwardKeySize +ForwardURICompat -ForwardDirectories JkRequestLogFormat "%w %V %T" JkMount /myApp/* loadbalancerLocal JkMount /myAppRemote/* loadbalancerRemote JkMount /myApp loadbalancerLocal JkMount /myAppRemote loadbalancerRemote The workers.properties config file is: worker.list=loadbalancerLocal,loadbalancerRemote worker.myAppLocalInstance1.type=ajp13 worker.myAppLocalInstance1.host=localhost worker.myAppLocalInstance1.port=8109 worker.myAppLocalInstance1.lbfactor=1 worker.myAppLocalInstance1.socket_keepalive=1 worker.myAppLocalInstance1.socket_timeout=1000 worker.myAppLocalInstance2.type=ajp13 worker.myAppLocalInstance2.host=localhost worker.myAppLocalInstance2.port=8209 worker.myAppLocalInstance2.lbfactor=1 worker.myAppLocalInstance2.socket_keepalive=1 worker.myAppLocalInstance2.socket_timeout=1000 worker.myAppLocalInstance3.type=ajp13 worker.myAppLocalInstance3.host=localhost worker.myAppLocalInstance3.port=8309 worker.myAppLocalInstance3.lbfactor=1 worker.myAppLocalInstance3.socket_keepalive=1 worker.myAppLocalInstance3.socket_timeout=1000 worker.myAppLocalInstance4.type=ajp13 worker.myAppLocalInstance4.host=localhost worker.myAppLocalInstance4.port=8409 worker.myAppLocalInstance4.lbfactor=1 worker.myAppLocalInstance4.socket_keepalive=1 worker.myAppLocalInstance4.socket_timeout=1000 worker.myAppRemoteInstance1.type=ajp13 worker.myAppRemoteInstance1.host=localhost worker.myAppRemoteInstance1.port=8509 worker.myAppRemoteInstance1.lbfactor=1 worker.myAppRemoteInstance1.socket_keepalive=1 worker.myAppRemoteInstance1.socket_timeout=1000 worker.myAppRemoteInstance2.type=ajp13 worker.myAppRemoteInstance2.host=localhost worker.myAppRemoteInstance2.port=8609 worker.myAppRemoteInstance2.lbfactor=1 worker.myAppRemoteInstance2.socket_keepalive=1 worker.myAppRemoteInstance2.socket_timeout=1000 worker.myAppRemoteInstance3.type=ajp13 worker.myAppRemoteInstance3.host=localhost worker.myAppRemoteInstance3.port=8709 worker.myAppRemoteInstance3.lbfactor=1 worker.myAppRemoteInstance3.socket_keepalive=1 worker.myAppRemoteInstance3.socket_timeout=1000 worker.myAppRemoteInstance4.type=ajp13 worker.myAppRemoteInstance4.host=localhost worker.myAppRemoteInstance4.port=8809 worker.myAppRemoteInstance4.lbfactor=1 worker.myAppRemoteInstance4.socket_keepalive=1 worker.myAppRemoteInstance4.socket_timeout=1000 worker.loadbalancerLocal.type=lb worker.loadbalancerLocal.sticky_session=True worker.loadbalancerLocal.balance_workers=myAppLocalInstance1,myAppLocalInstance2,myAppLocalInstance3,myAppLocalInstance4 worker.loadbalancerRemote.type=lb worker.loadbalancerRemote.balance_workers=myAppRemoteInstance1,myAppRemoteInstance2,myAppRemoteInstance3,myAppRemoteInstance4 worker.loadbalancerRemote.sticky_session=True

  Read the article

< Previous Page | 162 163 164 165 166 167 168 169 170  | Next Page >