Search Results

Search found 27649 results on 1106 pages for 'ask how to geek'.

Page 167/1106 | < Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >

• How do I make changes to /proc/acpi/wakeup permanent?

  - by Jolan

  I had a problem with my Ubuntu 12.04 waking up immediately after going into suspend. I solved the problem by changing the settings in /proc/acpi/wakeup, as suggested in this question: How do I prevent immediate wake up from suspend?. After changing the settings, the system goes flawlessly into suspend and stays suspended, but after I wake it back up, the settings in /proc/acpi/wakeup are different from what I set them to. Before going to suspend: cat /proc/acpi/wakeup Device S-state Status Sysfs node SMB0 S4 *disabled pci:0000:00:03.2 PBB0 S4 *disabled pci:0000:00:09.0 HDAC S4 *disabled pci:0000:00:08.0 XVR0 S4 *disabled pci:0000:00:0c.0 XVR1 S4 *disabled P0P5 S4 *disabled P0P6 S4 *disabled pci:0000:00:15.0 GLAN S4 *enabled pci:0000:03:00.0 P0P7 S4 *disabled pci:0000:00:16.0 P0P8 S4 *disabled P0P9 S4 *disabled USB0 S3 *disabled pci:0000:00:04.0 USB2 S3 *disabled pci:0000:00:04.1 US15 S3 *disabled pci:0000:00:06.0 US12 S3 *disabled pci:0000:00:06.1 PWRB S4 *enabled SLPB S4 *enabled I tell the system to suspend, and it works as it should. But later after waking it up, the settings are changed to either: USB0 S3 *disabled pci:0000:00:04.0 USB2 S3 *enabled pci:0000:00:04.1 US15 S3 *disabled pci:0000:00:06.0 US12 S3 *enabled pci:0000:00:06.1 or USB0 S3 *enabled pci:0000:00:04.0 USB2 S3 *enabled pci:0000:00:04.1 US15 S3 *enabled pci:0000:00:06.0 US12 S3 *enabled pci:0000:00:06.1 Any ideas? Thank you for your response. Unfortunately it did not solve my problem. all of /sys/bus/usb/devices/usb1/power/wakeup /sys/bus/usb/devices/usb2/power/wakeup /sys/bus/usb/devices/usb3/power/wakeup /sys/bus/usb/devices/usb4/power/wakeup as well as /sys/bus/usb/devices/3-1/power/wakeup are set to disabled, and the notebook still wakes up by itself right after going to sleep. The only thing it seems to react to are the settings in /proc/acpi/wakeup, which keep changing (resetting) every time i power off/restart my notebook.

  Read the article

• GRUB2 prompt instead of BURG boot screen after mistake during BURG installation

  - by Tomas Lycken

  I just installed BURG, but during the installation I made a mistake: after the package was installed, I got to some command-line based GUI for configuration, where I forgot to mark my (only) hard disk as the boot device before I hit OK. I tried to reinstall (apt-get purge burg && apt-get autoremove followed by apt-get install burg) but I wasn't able to get to the same screen again (I didn't find the GUI). When I now start my computer, I am taken to a GRUB2 prompt and no BURG (or GRUB2) boot menu is shown. Since I don't know any GRUB commands and I am helpless. How do I reinstall GRUB/BURG correctly? Update: I rebooted my computer, and got a BURG prompt (which appears to be the same thing as a GRUB prompt, but if there's a difference I wouldn't know it...). I have booted from a Live USB, but I don't know what to do next. The text above has been updated to reflect this new situation - for the original text, please see the previous versions of this post. (No answers were posted when this was edited...)

  Read the article

• How does one find out which application is associated with an indicator icon?

  - by Amos Annoy

  It is trivial to do this in Ubuntu 10.04. The question is specific to Ubuntu 12.04. some pertinent references (src: answer to What is the difference between indicators and a system tray?: Here is the documentation for indicators: Application indicators | Ubuntu App Developer libindicate Reference Manual libappindicator Reference Manual also DesktopExperienceTeam/ApplicationIndicators - Ubuntu Wiki ref: How can the application that makes an indicator icon be identified? bookmark: How does one find out which application is associated with an indicator icon in Ubuntu 12.04? is a serious question for reasons & problems outlined below and for which a significant investment has been made and is necessary for remedial purposes. reviewing refs. to find an orchestrated resolution ... (an indicator ap. indicator maybe needed) This has nothing to do (does it?) with right click. How can an indicator's icon in Ubuntu 12.04 be matched with the program responsible for it's manifestation on the top panel? A list of running applications can include all processes using System Monitor. How is the correct matching process found for an indicator? How are the sub-indicator applications identified? These are the aps associated with the components of an indicators drop-down menu. (This was to be a separate question and quite naturally follows up the progression. It is included here as it is obvious there is no provisioning to track down offending either sub or indicator aps. easily.) (The examination of SM points out a rather poignant factor in the faster battery depletion and shortened run time - the ambient quiescent CPU rate in 12.04 is now well over 20% when previously, in 10.04, it was well under 10%, between 5% and 7%! - the huge inordinate cpu overhead originates from Xorg and compiz - after booting the system, only SM is run and All Processes are selected, sorting on %CPU - switching between Resources and Processes profiles the execution overhead problem - running another ap like gedit "Text Editor" briefly gives it CPU priority - going back to S&M several aps. are at the top of the list in order: gnome-system-monitor as expected, then: Xorg, compiz, unity-panel-service, hud-service, with dbus-daemon and kworker/x:y's mixed in with some expected daemons and background tasks like nm-applet - not only do Xorg and compiz require excessive CPU time but their entourage has to come along too! further exacerbating the problem - our compute bound tasks no longer work effectively in the field - reduced battery life, reduced CPU time for custom ap.s etc. - and all this precipitated from an examination of what is going on with the battery ap. indicator - this was and is not a flippant, rhetorical or idle musing but has consequences for the credible deployment of 12.04 to reduce the negative impact of its overhead in a production environment) (I have a problem with the battery indicator - it sometimes has % and other times hh:mm - it is necessary to know the ap. & v. to get more info on controlling same. ditto: There are issues with other indicator aps.: NM vs. iwlist/iwconfig conflict, BT ap. vs RF switch, Battery ap. w/ no suspend/sleep for poor battery runtime, ... the list goes on) Details from: How can I find Application Indicator ID's? suggests looking at: file:///usr/share/indicator-application/ordering-override.keyfile [Ordering Index Overrides] nm-applet=1 gnome-power-manager=2 ibus=3 gst-keyboard-xkb=4 gsd-keyboard-xkb=5 which solves the battery ap. identification, and presumably nm is NetworkManager for the rf icon, but the envelope, blue tooth and speaker indicator aps. are still a mystery. (Also, the ordering is not correlated.) Mind you, it was simple in the past to simply right click to get the About option to find the ap. & v. info. browsing around and about: file:///usr/share/indicator-application/ordering-override.keyfile examined: file:///usr/share/indicators file:///usr/share/indicators/messages/applications/ ... perhaps?/presumably? the information sought may be buried in file:///usr/share/indicators A reference in the comments was given to: What is the difference between indicators and a system tray? quoting from that source ... Unfortunately desktop indicators are not well documented yet: I couldn't find any specification doc ... Well ... the actual document https://wiki.ubuntu.com/DesktopExperienceTeam/ApplicationIndicators#Summary does not help much but it's existential information provides considerable insight ...

  Read the article

• "Never hide" Unity launcher via CCSM & gconf doesn't work

  - by Jim Holman

  All: I am running Unity 3D and I want to set my launcher to never hide. I first ran ccsm, and set "Hide Launcher" to "Never". I rebooted then logged back in and it was still auto-hiding. I then ran gconf-editor, I navigated to /apps/compiz-1/plugins/unityshell/screen0/options and then set launcher_hide_mode to 0. I again rebooted and logged back in. The launcher is still auto-hiding. Checking gconf-editor, launcher_hide_mode is set to 0, but this setting isn't active however. What can I do to get the launcher to Never hide? Thanks, Jim

  Read the article

• Port listening on localhost:8000 but not on ip:8000

  - by Marionette

  Hello I'm running a web application on port 8000. When I access it from the host server localhost:8000 it responds ok, 127.0.0.1:8000 also works, but 192.168.1.7:8000 does not work. 192.168.1.7 is the ip of my server. Also if i try to go to another web application running on port 80 it works 192.168.1.7 I enabled ufw firewall and set ufw default allow. I am using ubuntu server 12.04 Any suggestions on why I can't get to my app on port 8000 using the ip-address:8000? Thanks in advance!

  Read the article

• The Lord of the Rings Project Charts Middle Earth by the Numbers

  - by Jason Fitzpatrick

  How many characters from the Lord of the Rings series can you name? 923? That’s the number of entries in the LOTR Project–a collection of data that links family trees, timelines, and statistical curiosities about Middle Earth. In addition to families trees and the above chart mapping out the shift in lifespans over the ages of Middle Earth, you’ll find charts mapping out age distributions, the race and gender composition of Middle Earth, populations, time and distance traveled by the Hobbits in pursuit of their quest, and so more. The site is a veritable almanac of trivia about the Lord of the Rings and related books and media. Hit up the link below to explore the facts and figures of Middle Earth. LOTR Project [via Flowing Data] How Hackers Can Disguise Malicious Programs With Fake File Extensions Can Dust Actually Damage My Computer? What To Do If You Get a Virus on Your Computer

  Read the article

• Error when running binary with root setuid under encrypted home directory

  - by carestad

  I'm using a VPN script for Juniper's Secure Access protocol form here, which executes a binary located under ~/.juniper_networks/network_connect/ncsvc with the following permissions: -rws--s--x 1 root root 1225424 okt. 25 13:54 ncsvc But when I do, I get the following error: ncsvc> Failed to setuid to root. Error 1: Operation not permitted Moving/copying the ~/.juniper_networks folder to e.g. /opt/juniper (with the same owner permissions), I don't get the error. In the forum thread at Ubuntuforums someone pointed out that it's probably because I have encrypted my /home and thus a "problem" with ecryptfs. How can I fix this?

  Read the article

• How to Add the Windows Calculator to the Quick Access Toolbar in Microsoft Excel 2013

  - by Lori Kaufman

  Do you use the Windows Calculator to perform quick calculations while building spreadsheets in Excel? You can save time by adding the Calculator to the Quick Access Toolbar in Excel so you don’t have to leave the program to access the Calculator. To do this, click the down arrow on the right side of the Quick Access Toolbar and select More Commands from the drop-down menu. On the Quick Access Toolbar screen on the Excel Options dialog box, select Commands Not in the Ribbon from the Choose commands from drop-down list. Scroll down in the long list and select Calculator. Click Add to add the Calculator to the Quick Access Toolbar. Click OK to accept the change and close the Excel Options dialog box. You’ll see a Calculator icon on the Quick Access Toolbar. When you move your mouse over the icon, a hint displays saying “Custom.” Despite the label, when you click the icon, the Windows Calculator opens. The same procedure works for adding the Windows Calculator to Excel 2010, as well.     

  Read the article

• Eclipse juno: Can't install RadRails throws error for a gem I have installed already

  - by Bogdan M

  The thing is I installed Ubuntu 12.04, Java (for Eclipse), Eclipse, ruby, ruby gems, rails. Everything went smooth. When I tried to prepare Eclipse for ruby on rails, I installed ruby dev kit plugin. This worked, but RadRails failed with this error: Cannot complete the install because one or more required items could not be found. Software currently installed: org.radrails.rails-feature 0.7.2 (org.radrails.rails_feature.feature.group 0.7.2) Missing requirement: Rails Core Plug-in 0.7.2 (org.radrails.rails.core 0.7.2) requires 'bundle org.eclipse.update.core 0.0.0' but it could not be found Cannot satisfy dependency: From: org.radrails.rails-feature 0.7.2 (org.radrails.rails_feature.feature.group 0.7.2) To: org.radrails.rails.core [0.7.2]

  Read the article

• AFP and SAMBA shares are confusing my MacOS X Lion

  - by Pierre

  I've setup my file server running ubuntu 12.04 with AFP/Avahi and Samba shares. Simple configuration, nothing too complicated. I've given my AFP machine a different name than %h to avoid confusion when looking into my Finder. However, my mac os lion mbp still confuses the two and the only way to access the AFP shares is via direct connect to IP address. The samba machine name seems to be hardwired to hostname (I can only see that that workgroup can be changed). Is there anything I am missing or obvious that I need to set? Best regards and thank you in advanced Pierre

  Read the article

• Broadcom BCM4331 not working on new Mac Mini 5,1

  - by Jon

  I can't seem to get my wireless card working on my Mac Mini 5,1. Lspci returns: 03:00.0 Network controller: Broadcom Corporation BCM4331 802.11a/b/g/n (rev 02) But running "additional drivers" doesn't detect anything. The nm-applet menu reads "device not ready--firmware missing." What can I do to get this to work? Note, this is with 12.04.1, so many of the previous discussions (for 11.10, etc) probably don't apply here.

  Read the article

• no volume in kubuntu 10.04

  - by neha

  hello,I am having both gnome and kde on my system.as my gnome is working perfectly but in KDE is there is no sound being generated. output of apley -l and lspci commands is as follows.. neha@neha-laptop:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 3: INTEL HDMI [INTEL HDMI] Subdevices: 1/1 Subdevice #0: subdevice #0 and output of lspci command is: neha@neha-laptop:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c) 00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02) 00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02) 02:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 02:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) 02:09.2 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 12) 02:09.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12) 02:09.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev ff) 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 12) 0b:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 01) can anyone help me??

  Read the article

• ath9k driver does not weak up

  - by shantanu

  I know this is common question but i found no suitable answer, so i am asking this again. I installed ubuntu 11.10. I found the bug for ath9k, so set first network boot from BIOS menu. That's worked. I have upgraded to 12.04 yesterday. Now ath9k is creating problem again. First network boot is still enable. ath9k works at start. But failed(connect again and again) after couple of minutes. dmesg show error that it can not weak up in 500us. So i tried #compat-wireless-3.5.1-1. But result is same. I have also added #nohwcrypt=1 option in /etc/modeprob.d/ath9k.conf. Still no luck. I tried #rmmod and then modprobe sudo modprobe ath9k nohwcrypt=1 dmesg shows me error: [ 400.690086] ath9k: Driver unloaded [ 406.214329] ath9k 0000:06:00.0: enabling device (0000 -> 0002) [ 406.214348] ath9k 0000:06:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 406.214368] ath9k 0000:06:00.0: setting latency timer to 64 [ 406.428517] ath9k 0000:06:00.0: Failed to initialize device [ 406.428852] ath9k 0000:06:00.0: PCI INT A disabled [ 406.428887] ath9k: probe of 0000:06:00.0 failed with error -5 dmesg error when driver fail: 355.023521] ath: Chip reset failed [ 355.023524] ath: Unable to reset channel, reset status -22 [ 355.023556] ath: Unable to set channel [ 355.088569] ath: Failed to stop TX DMA, queues=0x10f! [ 355.122708] ath: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff [ 355.122714] ath: Could not stop RX, we could be confusing the DMA engine when we start RX up [ 355.263962] ath: Chip reset failed [ 355.263966] ath: Unable to reset channel (2437 MHz), reset status -22 [ 358.996063] ath: Failed to wakeup in 500us [ 364.004182] ath: Failed to wakeup in 500us I can not install fresh ubuntu because i have lots of application installed. System : Acer Aspire 4250 AMD dual core 1.6GHZ Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) EDITED Now i am in serious problem. No wifi device is not showing in ifconfig or lshw commands. Only ether-net interface shows. I tried (FN + WIFI) several times to enable the device but nothing helps. Now I have installed fresh ubuntu 12.04. Please help lshw -c network: *-network description: Ethernet interface product: 82566DC Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 02 serial: 00:19:d1:7a:8e:f9 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=2.0.0-k duplex=full firmware=1.1-0 ip=192.168.1.114 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:90300000-9031ffff memory:90324000-90324fff ioport:20c0(size=32) rfkill command does not show anything but no error.

  Read the article

• Forked-daapd with alternative soundcard

  - by Mah

  I am trying to configure forked-daapd on my computer, and everything goes well except that in configuration file I can not set a new value for the line corresponding to soundcard. This is the default code in the config file: #card = "default" I want to use a soundcard called "DG2", which is the soundcard no.1 and has a first device that ALSA recognizes as no.0. So, I change the line to the following: card = "hw:DG2,0" I restart the daapd service and the next time I play a file through iTune remote, I get a message in my server log file saying that it can not play the file because the device is busy. Any change in the device name will return a different error, saying that the device does not exist. I am pretty sure no other uses this external device, and I don't understand why I get this message. I have tried hwplug as well, with no result.

  Read the article

• 50 Years of LEDs: An Interview with Inventor Nick Holonyak [Video]

  - by Jason Fitzpatrick

  The man who powered on the first LED half a century ago is still around to talk about it; read on to watch an interview with LED inventor Nick Holonyak. The most fascinating thing about Holonyak’s journey to the invention of the LED was that he started off trying to build a laser and ended up inventing a super efficient light source: Holonyak got his PhD in 1954. In 1957, after a year at Bell Labs and a two year stint in the Army, he joined GE’s research lab in Syracuse, New York. GE was already exploring semiconductor applications and building the forerunners of modern diodes called thyristors and rectifiers. At a GE lab in Schenectady, the scientist Robert Hall was trying to build the first diode laser. Hall, Holonyak and others noticed that semiconductors emit radiation, including visible light, when electricity flows through them. Holonyak and Hall were trying to “turn them on,” and channel, focus and multiply the light. Hall was the first to succeed. He built the world’s first semiconductor laser. Without it, there would be no CD and DVD players today. “Nobody knew how to turn the semiconductor into the laser,” Holonyak says. “We arrived at the answer before anyone else.” But Hall’s laser emitted only invisible, infrared light. Holonyak spent more time in his lab, testing, cutting and polishing his hand-made semiconducting alloys. In the fall of 1962, he got first light. “People thought that alloys were rough and turgid and lumpy,” he says. “We knew damn well what happened and that we had a very powerful way of converting electrical current directly into light. We had the ultimate lamp.” How To Get a Better Wireless Signal and Reduce Wireless Network Interference How To Troubleshoot Internet Connection Problems 7 Ways To Free Up Hard Disk Space On Windows

  Read the article

• Why is Gnome-Shell thinking my "d" key minimizes all windows?

  - by Limitless

  I am on Ubuntu 12.04 LTS (in gnome-shell) and I am unable to use my "d" key. Regular gnome-2 works perfectly fine, but for some reason I cannot use my "d" key in gnome-3. I recently installed it and have been trying to figure this out, but I have no clue what's going on. I attempted to disable the keyboard shortcut that minimizes active windows, but that did not work. (My only option right now is to use CTRL-V to paste my "d"s.) On top of this, my arrow keys automatically move my windows and I cannot move through text using them. What's going on here, folks?

  Read the article

• Cannot connect to postgresql on port 5432

  - by Assaf Lavie

  I installed the Bitnami Django stack which included PostgreSQL 8.4. When I run psql -U postgres I get the following error: psql: could not connect to server: No such file or directory Is the server running locally and accepting connections on Unix domain socket "/var/run/postgresql/.s.PGSQL.5432"? PG is definitely running and the pg_hba.conf file looks like this: # TYPE DATABASE USER CIDR-ADDRESS METHOD # "local" is for Unix domain socket connections only local all all md5 # IPv4 local connections: host all all 127.0.0.1/32 md5 # IPv6 local connections: host all all ::1/128 md5 What gives? "Proof" that pg is running: root@assaf-desktop:/home/assaf# ps axf | grep postgres 14338 ? S 0:00 /opt/djangostack-1.3-0/postgresql/bin/postgres -D /opt/djangostack-1.3-0/postgresql/data -p 5432 14347 ? Ss 0:00 \_ postgres: writer process 14348 ? Ss 0:00 \_ postgres: wal writer process 14349 ? Ss 0:00 \_ postgres: autovacuum launcher process 14350 ? Ss 0:00 \_ postgres: stats collector process 15139 pts/1 S+ 0:00 \_ grep --color=auto postgres root@assaf-desktop:/home/assaf# netstat -nltp | grep 5432 tcp 0 0 127.0.0.1:5432 0.0.0.0:* LISTEN 14338/postgres tcp6 0 0 ::1:5432 :::* LISTEN 14338/postgres root@assaf-desktop:/home/assaf#

  Read the article

• Creating an installer for a python GTK3 application

  - by Noam Gal

  I have just finished developing a Python 2.7 application using Gtk3 for GUI. My question is, how can I now create an installer for Windows, Mac, and Linux (possibly three different installers) for my end-users to easily download the application without having to download python and GTK and such. I have never created an installer from a python script before. I have heard that are some tools for this purpose (py2exe? pyinstaller?), but I wouldn't know how and what to pack with them in order for it to be able to use Gtk3. Thanks in advanced, Noam.

  Read the article

• How to open OLE2 file format document

  - by Dominic Jordan Hasford

  I received a file that is .OLE2 format by email and I can't get it open. When I try to open it with Document Viewer (default pfd program ubuntu) it says it can't support it. I searched in the Software Center for OLE2, and it returned a program called RipOle. It says it opens that format, but you have to run it in the terminal and I don't know how. Does any one know how to open OLE2 documents? Or do you know how to work ripole? Thanks in advanced!

  Read the article

• Aliases not available when using sudo

  - by Danny Roberts

  I was playing around with aliases today and I noticed that aliases don't seem to be available whilst using sudo: danny@kaon:~$ alias alias egrep='egrep --color=auto' alias fgrep='fgrep --color=auto' alias grep='grep --color=auto' alias l='ls -CF' alias la='ls -A' alias ll='ls -alF' alias ls='ls --color=auto' danny@kaon:~$ ll -d / drwxr-xr-x 23 root root 4096 2011-01-06 20:29 // danny@kaon:~$ sudo -i root@kaon:~# ll -d / drwxr-xr-x 23 root root 4096 2011-01-06 20:29 // root@kaon:~# exit logout danny@kaon:~$ sudo ll -d / sudo: ll: command not found Is there any reason why you cannot use aliases whilst using sudo?

  Read the article

• Reverse Search Images Easily with the TinEye Client for Windows

  - by Asian Angel

  Are you a frequent user of TinEye and would like to integrate it into your favorite Windows system? Then get ready to enjoy Context Menu and App Window goodness with the TinEye Client for Windows. After you have downloaded the zip file, unzip it and run the setup file inside. Once the installation process has finished you will be asked if you would like to launch TinEye Client immediately or not. If not then you can access it later using the new shortcut added to the Start Menu. We chose to let the program launch automatically…this is what the main window looks like. For our test we decided to access the client via the Context Menu using a picture of Doc Brown’s DeLorean in hover conversion mode. HTG Explains: Understanding Routers, Switches, and Network Hardware How to Use Offline Files in Windows to Cache Your Networked Files Offline How to See What Web Sites Your Computer is Secretly Connecting To

  Read the article

• wireless LAN soft blocked on Ubuntu 13.10

  - by iacopo

  I've troubles with bluetooth and with lan. When I digit: rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: yes Hard blocked: no When I digit: lspci -v 00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Root Complex Subsystem: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Root Complex Flags: bus master, 66MHz, medium devsel, latency 0 00:01.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Trinity [Radeon HD 7600G] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Trinity [Radeon HD 7600G] Flags: bus master, fast devsel, latency 0, IRQ 48 Memory at c0000000 (32-bit, prefetchable) [size=256M] I/O ports at f000 [size=256] Memory at feb00000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at [disabled] Capabilities: Kernel driver in use: radeon 00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Trinity HDMI Audio Controller Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Trinity HDMI Audio Controller Flags: bus master, fast devsel, latency 0, IRQ 49 Memory at feb44000 (32-bit, non-prefetchable) [size=16K] Capabilities: Kernel driver in use: snd_hda_intel 00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) (prog-if 30 [XHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at feb48000 (64-bit, non-prefetchable) [size=8K] Capabilities: Kernel driver in use: xhci_hcd 00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 40) (prog-if 01 [AHCI 1.0]) Subsystem: Advanced Micro Devices, Inc. [AMD] Device 7800 Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 45 I/O ports at f190 [size=8] I/O ports at f180 [size=4] I/O ports at f170 [size=8] I/O ports at f160 [size=4] I/O ports at f150 [size=16] Memory at feb50000 (32-bit, non-prefetchable) [size=2K] Capabilities: Kernel driver in use: ahci 00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) (prog-if 10 [OHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18 Memory at feb4f000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci-pci 00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11) (prog-if 20 [EHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17 Memory at feb4e000 (32-bit, non-prefetchable) [size=256] Capabilities: Kernel driver in use: ehci-pci 00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) (prog-if 10 [OHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18 Memory at feb4d000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci-pci 00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 11) (prog-if 20 [EHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17 Memory at feb4c000 (32-bit, non-prefetchable) [size=256] Capabilities: Kernel driver in use: ehci-pci 00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 14) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller Flags: 66MHz, medium devsel Kernel driver in use: piix4_smbus 00:14.1 IDE interface: Advanced Micro Devices, Inc. [AMD] FCH IDE Controller (prog-if 8a [Master SecP PriP]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH IDE Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at f100 [size=16] Kernel driver in use: pata_atiixp 00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller (rev 01) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller Flags: bus master, slow devsel, latency 32, IRQ 16 Memory at feb40000 (64-bit, non-prefetchable) [size=16K] Capabilities: Kernel driver in use: snd_hda_intel 00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 11) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge Flags: bus master, 66MHz, medium devsel, latency 0 00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD] FCH PCI Bridge (rev 40) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, medium devsel, latency 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 11) (prog-if 10 [OHCI]) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18 Memory at feb4b000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci-pci 00:14.7 SD Host controller: Advanced Micro Devices, Inc. [AMD] FCH SD Flash Controller (prog-if 01) Subsystem: Advanced Micro Devices, Inc. [AMD] FCH SD Flash Controller Flags: bus master, 66MHz, medium devsel, latency 39, IRQ 16 Memory at feb4a000 (64-bit, non-prefetchable) [size=256] Kernel driver in use: sdhci-pci 00:15.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 0) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000e000-0000efff Prefetchable memory behind bridge: 00000000d0000000-00000000d00fffff Capabilities: Kernel driver in use: pcieport 00:15.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 1) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Memory behind bridge: fe900000-feafffff Capabilities: Kernel driver in use: pcieport 00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 0 Flags: fast devsel 00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 1 Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 2 Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 3 Flags: fast devsel Capabilities: Kernel driver in use: k10temp 00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 4 Flags: fast devsel 00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) Processor Function 5 Flags: fast devsel 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07) Subsystem: PC Partner Limited / Sapphire Technology Device 0123 Flags: bus master, fast devsel, latency 0, IRQ 46 I/O ports at e000 [size=256] Memory at d0004000 (64-bit, prefetchable) [size=4K] Memory at d0000000 (64-bit, prefetchable) [size=16K] Capabilities: Kernel driver in use: r8169 03:00.0 Network controller: Ralink corp. RT3290 Wireless 802.11n 1T/1R PCIe Subsystem: AzureWave Device 2b87 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at fea40000 (32-bit, non-prefetchable) [size=64K] Memory at fea30000 (32-bit, non-prefetchable) [size=64K] Capabilities: Kernel driver in use: rt2800pci 03:00.1 Bluetooth: Ralink corp. RT3290 Bluetooth Subsystem: AzureWave Device 2787 Flags: bus master, fast devsel, latency 0, IRQ 11 Memory at fea20000 (32-bit, non-prefetchable) [size=64K] Memory at fea10000 (32-bit, non-prefetchable) [size=64K] Memory at fe900000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at fea00000 [disabled] [size=64K] Capabilities: Thank you for all the help

  Read the article

• Mutt not working due to "gnutls_handshake: A TLS packet with unexpected length was received." error

  - by Vinit Kumar

  I am expecting lots of problem trying to make mutt work in Ubuntu 12.04. Here is my .muttrc : http://paste.ubuntu.com/1273585/ Here is the bug I am getting when i tried to connect. gnutls_handshake: A TLS packet with unexpected length was received. Do anyone knows a workaround to fix this error.If so please suggest it asap. Many Thanks in Advance! For debug here is the output of my mutt -v: http://paste.ubuntu.com/1273590/

  Read the article

• Tears of Steel [Short Movie]

  - by Asian Angel

  In the future a young couple reach a parting of the ways because the young man can not handle the fact that she has a robotic arm. The bitterness of the break-up and bad treatment from her fellow humans lead to a dark future 40 years later where robots are relentlessly hunting and killing humans. Can the man who started her down this dark path redeem himself and save her or will it all end in ruin? TEARS OF STEEL – DOWNLOAD & WATCH [Original Blog Post & Download Links] Tears of Steel – Blender Foundation’s fourth short Open Movie [via I Love Ubuntu] HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference How To Troubleshoot Internet Connection Problems

  Read the article

• What package do I need to install to develop plugins for gedit?

  - by Wes

  I'm using Ubuntu 12.04 with python 2.7.3 and PyGObject and I'd like to develop plugins for Gedit in python. I found a simple looking tutorial for this sort of thing here. According to the tutorial, I need the Gedit module to interact with the plugin interface: from gi.repository import GObject, Gedit I keep getting an import error when trying to import the Gedit module. So, my question is: what package do I need to install to get this module? I've tried: gedit-dev , gedit-plugins Edit: Here is the full traceback for the above statement: ERROR:root:Could not find any typelib for Gedit Traceback (most recent call last): File "<stdin>", line 1, in <module> ImportError: cannot import name Gedit

  Read the article

< Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >