Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 167/216 | < Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >

  • IP assignment in a /28 block

    - by mks
    Need help on setting up firewall router. My config is as below: Public static network ID: x.x.x.48/28 gateway: x.x.x.49 available IP for the hosts: x.x.x.52 to 62 gw_eth0 <-- fw_eth0 - fw_eth1 <-- dmz_switch Four servers are connected on dmz_switch (say s1, s2, s3, s4) all have to use public static IP address from the above block. Any recommendation on IP assignment and route setup? Do I need to subnet the above block further or simply use /32 netmask and point-to-point static routes in the above setup?

    Read the article

  • Cannot access SWITCH thru VPN

    - by MadBoy
    I've VPN connection set up that i connect to company with. I can connect to all devices (other switches, routers, servers from same subnet with same settings just diffrent ip) but I can't connect to NetGear Router GS748Tv3. Settings on switch: IP address 192.168.1.8 Subnet mask 255.255.255.0 Default gateway 192.168.1.1 Management VLAN ID: 0 (1 - 4094 or 0) (0 means all VLANs) Switch has 2 VLAN's configured 1 and 2. I can access this switch thru VPN if i log in to server and from server to switch but this is a little bit slower then normal way. Anything I'm missing?

    Read the article

  • Format External HD on Airport Extreme Base Station?

    - by David.Chu.ca
    I just got an Airport Extreme Base Station. I am planning to use this one replace my current Linksys router. This works fine. My another purpose of getting this device is to use its USB port to connect to several external HDs as my backup Time Machine. I can see one 500GB HD through Airport Base Station. However, I cannot format it by using Disk Utility. What I did is to connect the HD to my iMac directly first and then clean and format the disk by Disk Utility application. Then I move the HD to the Airport Base Station. After that I can designate the HD as my Time Machine destination. Is there any way to format the HD connected to Airport Base Station? Any issues to use an external HD through Airport Base Station for Time Machine backups?

    Read the article

  • unusual webpage access problem

    - by user28163
    This is one of the weirdest problems I've ever seen and I'm out of ideas. I cannot access a couple of websites from my home pc (for 3-4 days now), or at least they go really really slow ~700b/s I can access these same websites fine from my laptop from same IP address. - The websites originate from different countries and are huge popular sites. - I have tried both my PC's network cards. - I have reformatted my PC. - I have reset my router to factory settings. - I have created virtual computers on my PC, and from inside those I cannot access the webpages. - I have flushed my dns. - I tried specifying my dns server addresses to 8.8.8.8 and 8.8.4.4. I can only access the webpages using my PC, if I first connect to an outside VPN. Again, these sites work fine on the 2 other pcs in this house (same ISP and internet connection). help plz :)

    Read the article

  • Can't connect to YouTube from specific network

    - by Tyilo
    Using my current network, I am unable to connect to http://www.youtube.com/. It doesn't matter what browser I use or if I use a cli-command (wget, curl). Error in Google Chrome: Oops! Google Chrome could not connect to www.youtube.com Error using curl: curl: (7) couldn't connect to host If I use nslookup to get the IP-address of YouTube, I get 173.194.32.32. If I go to http://173.194.32.32/ in my browser it can connect, but as Google is probably checking the Host HTTP-header, it shows Google's frontpage instead. There is no blocked websites on the router and other devices on the network seems to work. My computer only has this problem on this specific network. I am using Mac OS X 10.8.2 on a MacBook (mid 2009).

    Read the article

  • Samsung i780 networking problem

    - by Infinity
    Hello guys! Maybe this is not the right place to ask this, but I give a try for it. Please don't rate it down, just ignore it if you don't like. So I have a Samsung i780 mobile phone and I would like to use the internet through my wireless router. I have connected to it. I got an IP address. My laptop is also connected to the same wireless network and I can ping the mobile phone and I get answer. When I open the internet explorer and enter an address it says that it cannot connect to the internet. I have googled very much, but can't find the problem. What do you think, what is the solution?

    Read the article

  • linux: mount old ATA disk to USB adapter

    - by 130490868091234
    I am trying to recover data from an old Linux that was installed in a computer on an ATA hard drive. I found a ScanLogic Corp. SL11R-IDE IDE Bridge (04ce:0002), an ATA adapter to USB 1.0 like the one in the picture: and after switching it on, I plugged it into a laptop with Ubuntu 12.04. I am used to the drives being automatically mounted, but this one doesn't show up in /media. After doing a dmesg, all I got is this: [215298.671924] usb 2-1.1: new full-speed USB device number 5 using ehci_hcd [215298.767330] scsi19 : usb-storage 2-1.1:1.0 [215299.841701] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.017258] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.197050] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.372730] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd I tried plugging in the adapter to the three different USB ports in my laptop (one of them USB 3.0), but got no luck with any of them. I get different devices under, for example: /dev/bus/usb/003/002 or /dev/bus/usb/002/004, but I don't get any /dev/sdbN links. The output blkid -o list -c /dev/null is just the laptop's partitions. I have tried taking out the jumper, putting it as master and as CS Enabled, but didn't change the result. Any ideas?

    Read the article

  • How to prevent partial crash during VLAN configuration on a HP ProCurve 3500

    - by vm370
    as you can see from my question, I have a VLAN configuration problem with a ProCurve3500. The goal is to remove a VLAN from the existing configuration, however when I use the WEB UI to do this, I cannot modify ports to be assigned to a different VLAN or the Default VLAN. I always get the message "config failed", which is not very helpful. When I try to do it over telnet, the router somehow partially crashes and somehow the utilization on all ports is at 100% and I can barely use the web ui. After a reboot everything is fine again, but the configuration was not changed... The traffic after this partial crash looks like a broadcast storm, however there are definitely no loops in the segment. I also updated to the latest stable firmware, but the problem persists. Thanks a lot in advance Br vm370

    Read the article

  • OS X Address Not Available - How do I open this port?

    - by GeoffreyF67
    I am trying to get xdebug working on my snow leopard box. It uses port 9000. When I ask slickedit to monitor this port is gives an error that the address is not available. I've gone to canyouseeme.org to see if the port is open. It says the port is NOT open. I've verified that I have that port forwarding to my box from the router and i do NOT have the mac firewall running. I'm stumped. Any ideas?

    Read the article

  • How do I configure pfsense as an outbound VPN client?

    - by Avery Chan
    We use pfsense as a router/firewall. Because we're based in China, it is useful for us to have VPN access for all our internal clients. Instead of each individual client connecting to a VPN server stateside, I'd like to configure pfsense as a VPN client and have all the network traffic be routed through it. Most of the posts I've seen regarding pfsense and VPN are concerning connecting to the LAN from outside; this is not what I want to do. Another option would be for an SSH tunnel to be initiated on the pfsense box with the LAN traffic routed through it. How do I configure pfsense to be able to do either of these? One huge caveat is that OpenVPN cannot be used. The solution I am looking for needs to use one of the other VPN protocols.

    Read the article

  • Domino 8.5.3: Modify Subject of Incoming Email

    - by Void
    I am a newbie in managing and development for Domino. Recently, I have request from other teams at work to set up a filter or agent for incoming mail. This is the requirement for the request: Look for Incoming Mail addressed to #CRITICAL (mutlipurpose, internal group containing a list of engineers) For mail matching Point 1, append "For Immediate Action: " to the front of the Subject Some restrictions I have: Only the Domino server is under my charge, not to touch on network-side or other servers No 3rd party software to be installed I have gone through the configurations in the Domino server and the closest thing I have to filtering Email is the Router/SMTP Restrictions... Rules. But this is not able to fulfill Point 2 in any way. Is this even possible using just Domino server settings, or through agents?

    Read the article

  • Lost contact with my NAS after changing its IP

    - by Beles
    I did some brain-dead reconfiguring of my D-Link DNS-323 NAS some days ago. I have a home network where each computer gets a dynamically allocated IP address starting at 192.168.1.100. The irritating point (for me at least) was that the NAS changed IP if the power went down or I turned off the router. I then had to remap a drive-letter to point to the new IP address of the NAS. To remedy that I configured the NAS to have a static IP, 192.168.0.10. I had no good reason to choose that IP, other than I found it in a user manual for the NAS. After I changed the IP and rebooted the NAS it disappeared from the network and was never to be found again. Now I have a black brick standing in my home, looking good, but "dead". Could anyone point me in a direction which helps me solve this problem? I have about 100gb worth of pic of my children on this brick so I really want it back :-) Sincerely,

    Read the article

  • 'DNS server isn't responding' error in windows 7 home premium

    - by pradeeptp
    Hi All, I bought a brand new Dell Studio 1558 just last week. It has windows 7 home premium 64-bit installed on it. My friend who is occupying the adjacent room has a laptop with windows XP. Both of us are connecting to the same wireless router of the hotel. My friend is able to connect to the wireless network without any trouble, but when I try to connect, I get the error "DNS service isn't responding". I get this error when I run the troubleshooting option. I met two more people in the same hotel with win XP laptop and they too dont have any problem. I have gone to possibly all the forums and website but I haven't been able to fix this error :(. I have done all the basic troubleshooting but I have no luck yet. Pls help. Following is one forum where the problem seem to have been trouble shooted but not for all. http://social.technet.microsoft.com/Forums/en/w7itpronetworking/thread/eeb84518-903d-46d1-9398-80cf211878d7

    Read the article

  • Set up Windows SBS dns server and vpn clients from brench office

    - by mn
    I have got some clients from bench office which connects vpn to main office. The Router from bench office assigned addresses from DHCP 192.168.1.0/255.255.255.0 and remote gateway assigned vpn ip addresses 10.10.20.0/255.255.255.0. There is a DNS server (Active Directory Win SBS 2000) and vpn client are registered with vpn address (10.10.20.0/255.255.255.0 and domain company.com.pl). I would like to register also primary bench subnet 192.168.1.0/255.255.255.0 with domain for example company.vpn.local I want to access vpn hosts for example: dev3.copmany.pkb.local and dev3.company.com using my Win SBS 2000 DNS server.

    Read the article

  • Dynamic dns client stops updating when login off Windows

    - by Sami-L
    Running a dynamic dns updater software on Windows server 2008 R2, when I log off the software stops updating, I concluded that I have to look for a dynamic dns client running as service, I found this task a bit heavy since there is a big variety on the net, it needs a long time to make the right choice as many details are to pay attention to, free, masked fees, fees, installed on machine, configured on router, trusted, not trusted, compliant with OS, not, ... That's why I am here to ask for help on this matter, I would like to be advised by skilled people, to find a trusted free dns updater (client) for Windows which can run as service, and maybe which can send email when update fails.

    Read the article

  • Plesk 10 port 8443 connection timeout

    - by GriffinHeart
    I've installed plesk 10 on centOS and after installing to access the cp you need to go https::8443 I'm not being able to, and would like to find out why i can ssh to the server and i can, from the server telnet, to those ports. from another machine i can ping it but when i try to telnet or go to that address i get connection timeout, happens with port 80 and 8443 from my netstat netstat -nlp | grep 8443 tcp 0 0 :::8443 :::* LISTEN 25205/sw-cp-serverd How do i find out whats causing the problem? I also have a router but firewall is at the minimum and the server configured as DMZ, also tried to redirect 8443 to 8443 of the server.

    Read the article

  • Ubuntu 9.04 Cannot Connect to visible open wifi ap (reason 6)

    - by Andrew Bolster
    I'm travelling currently so the last network i connected successfully to was my home wpa-psk network. I hadn't tried anything until i got to my accommodation that is an open network (that I'm on now on the Win7 partition on my laptop). The network (and a similar archetypical 'linksys' open network, aswell as some protected local networks are correctly displayed in network-manager and upon selection, it happily spins around to its hearts content for a while before saying 'no chance boy'. /var/log/syslog spills out the usual combination of wpa_supplicant and kernel messages, the most interesting of are that the kernel deauthentication reason 6 response. 6 apparently means class2FrameFromNonAuthStation...Client attempted to transfer data before it was authenticated. Anyone seen anything like this? I've already tried going closer to the router to no avail. I don't remember seeing this any other time I've connected to a open AP, even if that AP is far away. (Signal strength for this AP is good, kismet says its around -57dBm, well above the threshold of -80dBm, and I've tried all the suggestions from the 'Related Questions'

    Read the article

  • PC power supply & normal range for voltages reported in BIOS hardware monitor?

    - by Chris W. Rea
    I'm trying to diagnose whether my computer has an ample power supply. Sometimes when I play a video-intensive game, both monitors lose the video signal, even though the computer remains on and sound playing. A theory I have is: the video card isn't getting sufficient power. I can't imagine it's overheating because the machine is well-ventilated and the video card isn't hot to touch when this happens. Anyway, in my PC's BIOS there's a Hardware Monitor page, and among other voltages reported (such as CPU, DRAM, South Bridge, etc.) I can see the following values: 3.3V 3.152V 5V 4.944V 12V 11.872V Are those the voltages used by peripherals? What voltage should I be referencing if I want to know what my video card (PCI Express) is consuming? What is the normal range of values reported for those? My values above appear to be under by approximately 4.5%, 1.1%, and 1.1% respectively. Is that cause for concern? How else should I be determining if my power supply is "right-sized" for my PC and video card, or am I perhaps barking up the wrong tree?

    Read the article

  • syslog ip ranges to specific files using `rsyslog`

    - by Mike Pennington
    I have many Cisco / JunOS routers and switches that send logs to my Debian server, which uses rsyslogd. How can I configure rsyslogd to send these router / switch logs to a specific file, based on their source IP address? I do not want to pollute general system logs with these entries. For instance: all routers in Chicago (source ip block: 172.17.25.0/24) to only log to /var/log/net/chicago. all routers in Dallas (source ip block 172.17.27.0/24) to only log to /var/log/net/dallas. Finally, these logs should be rotated daily for up to 30 days and compressed. NOTE: I am answering my own question

    Read the article

  • Internet access only works after turning off and on the local connection

    - by AgentFire
    Every time I turn on the computer, it has no internet access. The network card is connected to a router which broadcasts the internet all over the office LAN. Once I turn off and then on the local connection (or network card), the internet access works. Rebooting and logging out/in again does not help. Only the turning off and on the network card gives me internet access. Why is that? How do I fix it?

    Read the article

  • Self-hosted browser-based remote desktop script?

    - by rlsaj
    I need a self-hosted browser based remote desktop script that will connect me from any PC to my work PC. I need to either host this script within my own dedicated hosting or on my work PC. The PC that I need to remote into is always the one PC (Win7) and the IP never changes, and I have access to the Router/Firewall within. I have tried many remote desktop services and applications - LogMeIn, Team Viewer, (Ultra/Tight) VNC, GoToMyPC and iTeleport Connect and even Windows Remote Desktop - and the web services (or ports) are blocked at whatever free wi-fi/hotel/coffee shop I am at. Note that I will need to be able to access this from any PC, so I won't be able to install any applications (or use any portable software) - hence my thinking that it will need to be browser based on a standard (not blocked) port. If I can set up a web based remote desktop application - really a homebrew LogMeIn - then I should solve my problem. What is the best option here?

    Read the article

  • Altq limits not being applied to UDP transfers

    - by overkordbaever
    I have a OpenBSD server acting as a router/firewall with yhr packet filter ruleset shown below, a linux server, and a linux client. When transferring files (using netcat) by TCP, the limits are applied (for example the 100mbit limit in the example), though when transferring data by UDP, the limits aren't applied; the file always takes the same amount of time no matter the queue bandwidth limit I set (I can even turn off the queues completely, and will still get the same result). Why aren't the queuing rules applied to UDP packages? The rules used: #queue rules altq on { $int_if, $ext_if } cbq bandwidth 100Mb queue { def, low } queue def bandwidth 0Mb cbq(default) queue low bandwidth 100Mb cbq #Passrules test pass out quick from $int_if to $ext_if queue low pass in quick from $ext_if to $int_if queue low pass out quick from $ext_if to $int_if queue low pass in quick from $int_if to $ext_if queue low I suppose this may be related a question I've previously asked, though since it's more of a separate question, I suppose a separate question should be used for this

    Read the article

  • Plesk 10 port 8443 connection timeout

    - by GriffinHeart
    I've installed plesk 10 on centOS and after installing to access the cp you need to go https::8443 I'm not being able to, and would like to find out why i can ssh to the server and i can, from the server telnet, to those ports. from another machine i can ping it but when i try to telnet or go to that address i get connection timeout, happens with port 80 and 8443 from my netstat netstat -nlp | grep 8443 tcp 0 0 :::8443 :::* LISTEN 25205/sw-cp-serverd How do i find out whats causing the problem? I also have a router but firewall is at the minimum and the server configured as DMZ, also tried to redirect 8443 to 8443 of the server.

    Read the article

  • Route an IP from WAN to a host on LAN on OpenWRT

    - by Zsub
    EDIT: I know how to use NAT, I specifically want the server to be reachable on two IP's, one private, one public, with the firewall of the OpenWRT in between, if feasible. At the office we have recieved a /29 from our ISP. The first address is reserved for their endpoint, so I'm free to use five addresses. We run a local network, so of course there is a router in between running OpenWRT to provide all hosts with (W)LAN (dhcp from a private range). However, we also have a server running OS X Server 10.6 (Snow Leopard) and I'd like that server to be accessible both from the LAN using a private IP as well as from the WAN on it's own public IP. Point of note is that the server only has one network port, so multiple NICs is not an option, unfortunately. How would I go about doing this?

    Read the article

  • Vmware Workstation Development Server on Laptop

    - by Koobz
    I'm running an Ubuntu guest OS on my Windows 7 laptop. Currently, I have it set up for bridged networking. The guest is os is configured for a static ip of 192.168.1.115, which depending on the network I'm connected to, may not be available. When I want to view my development work I hit that up in my web browser. I'm really looking for the following scenario: 1) My guest OS ip address stays constant. 2) I can access my guest os even if I don't have an internet connection, or a lan/router. 3) I can share files with my guest/host. How does one accomplish this using VMware Workstation?

    Read the article

< Previous Page | 163 164 165 166 167 168 169 170 171 172 173 174  | Next Page >