Search Results

Search found 4899 results on 196 pages for 'ios newbie'.

Page 169/196 | < Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >

• New monitor connected to HDMI adaptor doesn't show output after booting

  - by Paul

  Hello out there in the multiple monitors’ world. I am a very old newbie in your world and need help. I just purchased a new Asus VH236H monitor and hooked it up the HDMI port of an ATI Radeon HD4300 / 4500 Series display adaptor. I left the old Princeton LCD19 (TMDS) hooked up to the DVI port of the same display adaptor. Both monitors displayed the boot sequence, after I fired good old Sarastro2 (Asus P5Q Pro Turbo – Dual Core E5300 – 2.60 GHz) up. The Asus lacked one half of a second behind the Princeton until the Windows 7 Ultimate SP 1 boot up was complete. Then the Asus displayed “HDMI NO SIGNAL” and went into hibernation. The Princeton stayed lit up as before. Both monitors are displayed on the “Screen Resolution Setup Display” and I plaid around with them for a while. The only thing I accomplished was to shove the desktop icons from the Princeton to the still hibernating Asus. The “Multiple displays:” is set to “Extend these displays”, the Orientation is “Landscape” and the Resolutions are set on both to the “recommended” one. Both monitors show that they work properly in the advanced Properties display. What am I doing wrong, what am I missing? Never mind the opinions about the different resolutions of the two monitors. I always can unhook the Princeton and give it to a Goodwill Store if I do not like the setup. I just would like to make it work. Any constructive help is very much appreciated, Thank you.

  Read the article

• Looking for software to create a personal hotspot on Mac OS X (not using the built-in ability)

  - by Fred

  I got my nifty little MacBook Air today. Since I will be going on travel I was hoping to use my iPad 3G as screen extension with Air Display. It works being in a shared WiFi network. Sadly Apple is a bit restrictive on the tethering with their mobile devices such as the iPad. Now I read iOS 4.3 will enable the iPad to use tethered networks. But the feature will not be working for iPad 3G. I assume their big partner telecom companies fear everyone will quit their internet contract with them. So I want to create a personal hotspot on my MacBook and use it on my iPad. But the iPad is not able to use this network. The network is visible but not usable. On Windows there is this connectify program which lets the PC act as wireless router. Does anybody know a similar program for Mac which would turn it into a wireless router? Or is there something I don't see with Mac OS X's builtin features?

  Read the article

• Failed to mount to nfs server with "Program not Registered"

  - by Farrel

  I'm trying to setup nfs server on Fedora 17 and I'm getting "Program not Registered" error when I'm trying to mount. I guess the main reason for this is rpcbind. I'm a newbie in linux, so I don't know what info should I provide you with. Here is some info that might be useful. rpcinfo -p program vers proto port service 100000 4 tcp 111 portmapper 100000 3 tcp 111 portmapper 100000 2 tcp 111 portmapper 100000 4 udp 111 portmapper 100000 3 udp 111 portmapper 100000 2 udp 111 portmapper 100005 1 udp 20048 mountd 100005 1 tcp 20048 mountd 100005 2 udp 20048 mountd 100005 2 tcp 20048 mountd 100005 3 udp 20048 mountd 100005 3 tcp 20048 mountd 100024 1 udp 42223 status 100024 1 tcp 50054 status cat /etc/exports /home/Farrel/prog 192.168.xxx.xxx (ro,sync) service nfs status Redirecting to /bin/systemctl status nfs.service nfs-server.service - NFS Server Loaded: loaded (/usr/lib/systemd/system/nfs-server.service; enabled) Active: active (exited) since Fri, 02 Nov 2012 09:29:04 +0300; 5min ago Process: 924 ExecStartPost=/usr/lib/nfs-utils/scripts/nfs-server.postconfig (code=exited, status=0/SUCCESS) Process: 909 ExecStart=/usr/sbin/rpc.nfsd $RPCNFSDARGS ${RPCNFSDCOUNT} (code=exited, status=0/SUCCESS) Process: 885 ExecStartPre=/usr/sbin/exportfs -r (code=exited, status=0/SUCCESS) Process: 864 ExecStartPre=/usr/lib/nfs-utils/scripts/nfs-server.preconfig (code=exited, status=0/SUCCESS) CGroup: name=systemd:/system/nfs-server.service Warning: Journal has been rotated since unit was started. Log output is incomplete or unavailable. Firewall is disabled on both systems. I spent a lot of time reading on the topic but all manuals on setting up nfs server lead to "Program not Registered" error. Any how-to-fix-it ideas?

  Read the article

• cisco 2900xl - SNMP - Get mac address of device connected to an interface

  - by ankit

  Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

  Read the article

• Hard wrapping in vim without joining

  - by Miles

  Vim newbie here. How can I hard wrap plain text in vim (inserting actual linebreaks), respecting word boundaries, without joining existing lines? For example, given this: Lorem ipsum dolor sit amet, consectetur adipiscing elit. - Nulla cursus accumsan faucibus. - Donec dapibus dignissim ullamcorper. Integer nec malesuada diam. I'd like to get (with textwidth=30): Lorem ipsum dolor sit amet, consectetur adipiscing elit. - Nulla cursus accumsan faucibus. - Donec dapibus dignissim ullamcorper. Integer nec malesuada diam. instead of this (which I can get with gggqG) Lorem ipsum dolor sit amet, consectetur adipiscing elit. - Nulla cursus accumsan faucibus. - Donec dapibus dignissim ullamcorper. Integer nec malesuada diam. Also, for bonus points: when I create a brand new buffer, I get different wrapping behavior (lines beginning with - aren't wrapped specially) than when I open a file ending in .txt. What controls this? I don't notice any difference in the output of :set filetype? or :filetype.

  Read the article

• Basic multicast network performance problems

  - by davedavedave

  I've been using mpong from 29west's mtools package to get some basic idea of multicast latency across various Cisco switches: 1Gb 2960G, 10Gb 4900M and 10Gb Nexus N5548P. The 1Gb is just for comparison. I have the following results for ~400 runs of mpong on each switch (sending 65536 "ping"-like messages to a receiver which then sends back -- all over multicast). Numbers are latencies measured in microseconds. Switch Average StdDev Min Max 2960 (1Gb) 109.68463 0.092816 109.4328 109.9464 4900M (10Gb) 705.52359 1.607976 703.7693 722.1514 NX 5548(10Gb) 58.563774 0.328242 57.77603 59.32207 The result for 4900M is very surprising. I've tried unicast ping and I see the 4900 has ~10us higher latency than the N5548P (average 73us vs 64us). Iperf (with no attempt to tune it) shows both 10Gb switches give me 9.4Gbps line speed. The two machines are connected to the same switch and we're not doing any multicast routing. OS is RHEL 6. 10Gb NICs are HP 10GbE PCI-E G2 Dual-port NICs (I believe they are rebranded Mellanox cards). The 4900 switch is used in a project with tight access control so I'm waiting for approval before I can access it and check the config. The other two I have full access to configure. I've looked at the Cisco document[2] detailing differences between NX-OS and IOS w.r.t multicast so I've got some ideas to try out but this isn't an area where I have much expertise. Does anyone have any idea what I should be looking at once I get access to the switch? [1] http://docwiki.cisco.com/wiki/Cisco_NX-OS/IOS_Multicast_Comparison

  Read the article

• sendmail Name server timeout

  - by broody

  Complete sendmail newbie here... I've been trying to get mailing to work in PHP and I've root caused it down to sendmail's complaint about "Name server timeout": >sendmail -t -v >From: [email protected] >To: [email protected] >. gmail.com: Name server timeout [email protected]... Transient parse error -- message queued for future delivery [email protected]... queued So it sounds like a DNS issue? But I can do a "dig mx gmail.com" and it will query successfully. Here's what confuses me... I can get sendmail to work two other ways. The first way is through telnet: >telnet 127.0.0.1 25 >Helo me >Mail from: [email protected] >Rcpt to: [email protected] >. message sent And the second way is by explicitly appending the sendmail.cf, but this is strange because it's the exact same file I use to configure sendmail to begin with: >sendmail -t -v -C/etc/mail/sendmail.cf But none of these solutions will resolve my PHP mailing... I am clueless as to what is going on... appreciate any help.

  Read the article

• JBoss 5 on AIX 5.3

  - by jess

  I am a very newbie for AIX and system monitoring. Actually our application currently run production on jboss 5.1 in AIX 5.3. Please check below configuration & system settings. AIX system configuration OS Level 5.3.9.0 (oslevel -g) Physical Memory size 24GB (svmon -G) Page space 4GB (lsps -s) processors 3 cores, Processor Type: PowerPC_POWER6, Processor Clock Speed: 4704 MHz (prtconf | grep Processor) Java version JRE 1.6.0 IBM AIX build pap6460sr10fp1-20120321_01 (SR10 FP1) (java -fullversion) JBoss configuration JBoss 5.1/JBoss ESB 4.11 Hornetq messaging with consumer flow control java opts : -d64 -Xms2g -Xmx4g -XX:MaxPermSize=1024m Sometime we observe very strange behavior in the JBoss that freeze without any error logs. Also server log stop without any further trace. We also not able to get thread dump (kill -3) and its not generate at that point. (kill -3 xxxxx works in normal circumstances) Only option available for us was restart the jboss server and its seem all messages that were in queues during the freeze time process after restarting. We try tweak some of setting in JBoss hornetq, we though issue was there. Hornetq Stuck By Default. But we haven't any luck and also unable to isolate the issue in any point. We looking at tool like nmon for monitoring this but no clue is that good enough to do so. Please provide some point to investigate this issue. Thanks

  Read the article

• Why my 2nd ip from traceroute is not answering the ping anymore?

  - by Pedro77

  My Internet is really laggy today, I did a tracerout and I realize that I'm having no answer from an ip at the beginning of the traceroute. see: Tracing route to 12.129.202.154 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.0.1 2 * * * Request timed out. 3 8 ms 8 ms 8 ms bd044008.virtua.com.br [189.4.64.8] 4 9 ms 8 ms 8 ms bd044009.virtua.com.br [189.4.64.9] 5 26 ms 26 ms 24 ms embratel-T0-1-5-0-tacc01.cas.embratel.net.br [200.174.243.21] 6 360 ms 15 ms 12 ms ebt-T0-15-0-12-tcore01.ctamc.embratel.net.br [200.244.140.218] 7 330 ms 349 ms 261 ms ebt-Bundle-POS11942-intl04.mianap.embratel.net.br [200.230.220.10] 8 139 ms 141 ms 139 ms sl-st30-mia-.sprintlink.net [144.223.64.221] Connection diagram: PC - Router configured as access point - Router (192.168.0.1) - Cable modem (192.168.100.1). Well, I think it is odd that the 2nd ip is not returning the ping. I looked some old tracerout logs to see what was the 2nd ip. The ip was: 10.19.0.1 So, what this 2nd ip stand for? How can I find why it is not answering the ping? I don't understand it, if does not answer the ping, how can the packets continue (yeah newbie question)? edit: well, because the hope 3 have a ping of 8 ms the hop 2 request time out should really not be a problem. But it is still odd that the 2nd hop stopped to answer ping request. So my doubts are: 1. Were the ip 10.19.0.1 is from? 2. Why it stopped to answer ping requests? 3. How can hop 7 be smaller than 6 and 8 smaller than 7 and 6!?? Shouldn't the pings be higher for each hop? Like: hop 3 time should be the sum of the hops before it plus its own time (hop 3 = 1+2+3) ??

  Read the article

• Upgrading openSUSE 11.1 with Plesk Panel 9.3 to PHP 5.3

  - by Jonathan Hogervorst

  Hello, I'm running a VPS with openSUSE 11.1 (i586). On the VPS is Parallels Plesk Panel 9.3.0 installed. The current PHP-version is PHP 5.2.11. I want to upgrade PHP to PHP 5.3, but I can't find good instructions on how to do this. If I check for updates in Zypper, it says this is the latest release. In the Plesk Updates isn't an update either, both via the webbased interface and the command line interface. On Software.openSUSE.org I can find packages for PHP 5.3.1 in both the server:php/server_apache_openSUSE_11.1-repo and the server:php/openSUSE_11.1-repo (can't post the link because I'm a newbie here). But if I add one of those to Zypper, I still don't see an update. Is there here somebody who knows how to do this? And is it completely safe to update that way? I don't want to end up with a broken VPS... Thanks! Jonathan

  Read the article

• What to do when launchpad is down?

  - by Jon

  As I am writing this (Friday, November 8, 2013 at 9:59:18 PM EST) launchpad is down. Apparently there is a power failure (https://twitter.com/launchpadstatus/status/398980619880775680). I tried running sudo apt-get update on my Ubuntu install. However, I simply get stuck on this: Ign http://ppa.launchpad.net precise InRelease 100% [Waiting for headers] Being a Ubuntu newbie, I tried to point my sources.list file to a different source. I backed up the original sources.list and then deleted the entire file to start afresh. I then added the following lines to it: deb http://mirror.anl.gov/pub/ubuntu/ precise main deb-src http://mirror.anl.gov/pub/ubuntu/ precise main I figured that since I have a different mirror, there would be no problem updating. I was wrong. I get stuck at the same place. I have several questions: Why do I need to hit launchpad? I do not reference it in my sources.list file at all. Is this something where the mirror redirects me to launchpad? Is there a good article out there that I can read on how exactly this whole apt-get update thing works that will help me understand why it is hitting launchpad? Is there any way to get my Ubuntu to update while launchpad is down? Isn't there any redundancy for the launchpad servers?

  Read the article

• How to configure router to give XBox top priority / most bandwidth?

  - by MrSparky

  Hi all - Newbie here so go easy... and apologies in advance if I blow the community etiquette / rules! Here's what I'm trying to do: I have a "D-Link DIR-655 Extreme N" wireless router and an XBox 360 w/ the old-style wireless connection thing (usb attachment)... I want to configure my router / network to give my XBox as much bandwidth as it wants, whenever it wants. I have tried giving the XBox a unique IP (within my network) and then tweaking the router to treat that IP as a top priority application (using the router's QOS stuff). Problem is whenever I turn off the xbox, I can't connect to the network the next time I start it up. It seems the only reliable setting in the XBox is to use "Automatic" for the IP settings within the Network Configuration area. Supposedly the D-Link ships with default settings that attempt to recognize a game console and give it top priority... but i've not seen good results (lots of stuttering / lag when someone else jumps online, etc). Any suggestions? thanks again!

  Read the article

• Thin client - cloud machine - to run via iPad, iPhone, most Androids etc

  - by Carl Lindberg

  I'm tired of having a laptop macbook that breaks down or having files that I need to sync via dropbox etc all the time via the machines to different OS installations. It sucks. I want a thin client where I can login on any machine - my iPhone, PC desktop, iPad etc to one running machine. I would like to replace a modernly powerful desktop iMac with a thin client running via my iPad. I will connect the iPad with a keyboard/mouse too so you get the idea. But I want to be able to use some of the Android phones as well (I guess most Android phones today has a good enough performance/resolution etc to run a thin client). Of course it has to be able to have input/output in sound. Printing can be solved by PDF/emailing etc - so no direct communication to the printer ports to USB etc is necessary. Is there such a service today? It should cost somewhere under something like $40/ month. I will run stuff like CPU heavy duty ableton for music production, xCode for making iOS apps, some games etc. And on the thin client also run virtual machines. VM of Ubuntu and Windows.

  Read the article

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

• Limiting access in Silverlight\Pivotviewer

  - by sparaflAsh

  I'm going to deploy a pivotviewer application. As some of you might know this silverlight application load a .cxml index file for a group of images. My need is to make .cxml file and image files not accessible for the user. Now, if I don't have a need I usually code like this in C# and the file is hosted in the documentroot: _cxml = new CxmlCollectionSource(new Uri("http://www.myurl.it/Collection.cxml", UriKind.Absolute)); This means that my cxml and then the images are available by http for everyone who knows the URI. I'm a newbie to server configuration, so any help/hint would be deeply appreciated. Someone suggested me to take the files out of the root, but it seems like I can't go to pick them up if they are not a URL in Silverlight. At least I didn't managed to understand how. Someone else suggested me to play with web.config file to hide URLs, but I don't really know where to start. My question is, what's the best practice to hide my stuff? Obviously I can edit the question if you need more details.

  Read the article

• Deployment and Ownership issues

  - by kylemac

  As an extreme newbie, I am having difficulty managing ownership and permissions on my first box. What I can't figure out is how to deploy using one user, we will call him deploy and operate my php application with www-data user. Currently as it stands, I know my server runs as www-data through this function <?php echo(exec("whoami")); ?> but I am having to chown between deploy and www-data every time I deploy. There has got to be an easier way to deploy with one user and still run as www-data. EDIT: Here is the output from ls- l on the folder in question. You will see user deploy and group www-pub, the group is from an attempt to add the two different users to a new group and chown one of them in the hopes that they both would have the permissions (newb alert) drwxrwxr-x 4 deploy www-pub 4096 Mar 7 01:41 example.com I am using capistrano for deployment under the user deploy then once its done i chown to www-data, otherwise I can't use php to manipulate files. I am also unsure how to even change which user apache is running.

  Read the article

• permanent NAS-mount in Ubuntu - wrong fs type, bad option, bad superblock

  - by Emil

  My network drive shows up in the file browser, just like my external usb-harddrive. Moving, running and editing files works. Hovering over it shows smb://lacie-2big/nasdisk . BUT, when I want to save a file, the drive doesn't come up as an option. All I can see is my other places, including my usb-harddrive. I am a complete newbie but I am GUESSING that it has something to do with the mount not being a "real" mount but just a shortcut to the smb location. So I ran the tutorial at https://wiki.ubuntu.com/MountWindowsSharesPermanently about how to "mount a network drive permanently". edited my fstab to //LaCie-2big/nasdisk /media/nasmount cifs guest,uid=1000,iocharset=utf8,codepage=unicode,unicode 0 0 and running sudo mount -a gave me the following error: mount: wrong fs type, bad option, bad superblock on //LaCie-2big/nasdisk, missing codepage or helper program, or other error (for several filesystems (e.g. nfs, cifs) you might need a /sbin/mount. helper program) In some cases useful info is found in syslog - try dmesg | tail or so Now thats a very helpful error message, BUT, before I go any further, I'd be really thankful if one of you could tell me if I'm even in the right ballpark, or if my actual need: to be able to download files (ie torrents) directly to the drive, can be possible as it is already. Question: How to fix "wrong fs type, bad option, bad superblock on //LaCie-2big/nasdisk, missing codepage or helper program" when running mount -a

  Read the article

• Apache virtualhost - only apply script if file does not exist in document root

  - by Brett Thomas

  Sorry for the newbie apache question. I'm wondering if it's possible to set up the following non-conventional apache virtualhost (for a Django app): -- If a file exists in the DocumentRoot (/var/www) it will be shown. So if /var/www/foo.html exists, then it can be seen at www.example.com/foo.html. -- If file does not exist, it is served via a virtualhost. I'm using mod_wsgi with a WSGIScriptAlias directive that points to a Django app. So if there is no /var/www/bar.html, www.example.com/bar.html will be passed to the Django app, which may or may not be a 404 error. One option is to create an Alias for each individual file/directory, but people want to be able to post a file without adding an alias, and we want to keep the above URL structure for legacy reasons. Simplified Virtualhost is: <VirtualHost *:80> ServerName www.example.com DocumentRoot /var/www WSGIScriptAlias / /path/to/django.wsgi <Directory /path/to/app> Order allow,deny Allow from all </Directory> Alias /hi.html /var/www/hi.html </VirtualHost> The goal is to have www.example.com/hi.html work as above, without the Alias line

  Read the article

• Why won't this script accept any arguments?

  - by Nate Wagar

  I'm trying to write an SVN post-commit hook and, strangely, am getting hung up on what should be the easiest part. The Script: set REPO="$1" set REV="$2" set SVNBIN="/opt/CollabNet_Subversion/bin/" set SSHBIN="/usr/bin/ssh" set HOST="staging.domain.net" set timeout=30 set USERNAME="svn-usr" set E_NO_CONNECT=2 set E_WRONG_PASS=3 set E_UNKOWN=25 set CHANGED=`"$SVNBIN"svnlook changed --revision $REV $REPOS` echo "Here are changes: $CHANGED" >> /var/svn/repos/www/logs/testing echo "Command: $0; Repo: $REPO; Rev: $REV; Total: $#" >> /var/svn/repos/www/logs/testing set PROJECT "" Yet when I call it, it doesn't seem to be seeing the arguments I pass to it: /var/svn/repos/www/logs> sudo ../hooks/post-commit /var/svn/repos/www 33 svnlook: missing argument: --revision Type 'svnlook help' for usage. /var/svn/repos/www/logs> cat testing Here are changes: Command: ../hooks/post-commit; Repo: ; Rev: ; Total: 1 This is on a Solaris 10 SPARC box. I'm a bit of a script newbie, but shouldn't this be really easy??

  Read the article

• Cannot find FIS partition 'initramfs'......... need help!!!

  - by vikramtheone

  Hi Guys, I have a Ubuntu 9.04 Linux running on Freescale's i.MX515(ARM Cortex based) board with me. There were about 250 updates pending and I did that today, well some of the updates failed because of the infamous errors: E: dpkg was interrupted, you must manually run 'sudo dpkg --configure -a' to correct the problem. E: Couldn't rebuild package cache E: dpkg was interrupted, you must manually run 'sudo dpkg --configure -a' to correct the problem. So, when I do the 'sudo dpkg --configure -a' I get new errors related to FIS partition: Cannot find FIS partition 'initramfs' User postinst hook script [/usr/sbin/flash-kernel] exited with value 1 dpkg: error processing linux-image-2.6.28-18-imx51 (--configure): subprocess post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of linux-image-imx51: linux-image-imx51 depends on linux-image-2.6.28-18-imx51; however: Package linux-image-2.6.28-18-imx51 is not configured yet. dpkg: error processing linux-image-imx51 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-imx51: linux-imx51 depends on linux-image-imx51 (= 2.6.28.18.23); however: Package linux-image-imx51 is not configured yet. dpkg: error processing linux-imx51 (--configure): dependency problems - leaving unconfigured Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-2.6.28-18-imx51 Cannot find FIS partition 'initramfs' dpkg: subprocess post-installation script returned error exit status 1 Whats going wrong here, need help!!! I'm a newbie. Regards Vikram

  Read the article

• Single computer on network cannot connect to internet.

  - by user34630

  Hi All, I hope you can help me out! :) I have 3 computers and one device (Xbox) on my home network; 2 running XP and one on Vista. The computer that can't connect to the internet (XP) is old and failing, and shows no warning before it completely runs out of battery. Thus today, I started it up forgetting that I had unplugged it the night before, and it just ran out of battery entirely whilst I was using it and died. I think that before this I had been browsing the internet, but I can't remember for certain. (i.e. The problem I am having may or may not have been caused by this 'hard' power off). Anyway, now when I start the computer up it takes 5-10 minutes after logging on to display the start bar and icons. Also, I cannot browse the internet. The computer seems to connect to the network OK (I have tried both wired and wireless), but I can't visit sites and can't ping web addresses. Pinging the router fails, as does pinging another of my computers on the network. I have never encountered something like this before, and whilst I am no noob I am also not a sysadmin, haha. :( Any help is greatly appreciated, thank you for your time. P.S. I have tried a system restore (newbie move?).

  Read the article

• certificate working on IP but not on URL

  - by Stephan

  I asked this question on stackoverflow, and I've been suggested to repost it here. I have a problem accessing my site (on https) with IEMobile 9 (WP 7.5). It says it's got problem with the certificate, as if it wasn't valid. Everything works on any other browser or platform I tested (android (several phones and a galaxy tab with stock browser, firefox, opera, dolphin), iOS (iphone and ipad with safari and chrome), an old nokia with symbian, windows 7, linux and mac). To try to solve this I saved the certificate (.cer) on the server and accessed it from the phone browser. It always complained except when I accessed it through the server IP (192.168.xx.xx). At that point it (said it) installed correctly the certificate. If then I try to access the index.html still using the IP all works fine and it doesn't complain about the certificate. If, though, I try to access the index using the actual URL (blah.myblah.com), it complains again about the certificate, as if it wasn't installed! It isn't a problem of DNS, cause that's up and serving the right ip, and the phone is correctly setup to use it. The certificate is signed by geotrust/rapidssl for *.myblah.com.

  Read the article

• Experiences in Upgrading from Exchange 2003 to Exchange 2010

  - by gWaldo

  I'm currently running Exchange 2003 SP2 Cluster on a Server 2003 AD Forest (in native 2003 mode), and we beginning to plan the upgrade to Server 2008 AD and Exchange 2010. We have two main sites, one middle-sized office, and a couple of smaller sites which have DCs (which may be RODCs after the upgrade). Currently all of our Exchange cluster is in my main site, but we are considering using the new datastore paradigm for load-balance/failover at the other large site, but this is not set in stone. Right now we are in the information-gathering and planning phases. I am looking for input of any gotchas experienced while performing either upgrade, but especially the Exchange upgrade. Gotchas? What surprised you? What wasn't documented? What said one thing but was misleading? (Confusing either in content or severity.) What is great or horrible about the new system? What worked well? What worked poorly? If you were to do it over again...? (I know that this isn't so much a question that can be definitively answered, but I'm happy to reward insight and useful resources (not the Microsoft documentation, but Blogposts are welcome) with upvotes.) UPDATE A couple items of note: -We are not currently using OWA (currently only the admins), but it may become more of a consideration with iOS devices. -We do have a small number of Blackberries in the environment (< 10%). -In addition to the standard Exchange connectors, we have a third-party connector for Captaris RightFax integration.

  Read the article

• How to set up port forwarding on a dedicated server running CentOS 5.4 to use Ubuntu 9.0.4

  - by mairtinh

  The basic situation that I have is a dedicated server running CentOS 5.4 At the moment I have one VM running Ubuntu 9.0.4. Later on, I will want to add another VM running Windows Server 2003 but at the moment I am focusing on getting Ubuntu up and running. The Ubuntu installation is working fine but I'm seriously struggling to get port forwarding working so that I can access websites to be hosted on the Ubuntu VM. As a newbie to Linux, I am confused about the relationship between IPTables and VMWare's own port forwarding. Here's what I've tried so far. The IP of my server is xxx.xxx.xxx.xxx and the provider support have told me that the subnet mask is 255.255.255.0, the gateway address is xxx.xxx.xxx.1 and the network address is xxx.xxx.xxx.0. (Those latter two surprise me a bit, I expected private gateway/network address rather than public ones.) First of all I tried Bridged Networking but had no success at all in communicating with the machine other than through the VMware console. I tried pinging it from the host (using ssh into the host) but no joy; also no Inernet access from the VM. I changed the interfaces configuration from DHCP to Static, using a static address of 192.168.1.100 and setting the gateway to xxx.xxx.xxx.1 as advised by the provider. No real difference, still cannot ping the guest from the host or vice versa and no Internet access from the guest. Then I tried NAT. The host automatically set the IP address to 192.168.132.128 with a gateway of 192.168.132.2 Now the guest has Internet access out and when I do a VNC to the host and open Firefox with 192.168.132.128 I can see the hosted website okay but I still cannot get into it from outside. I mentioned that I'm a bit confused about IPtables and VMware port forwarding, what I meant is that I'm not sure whether IPtable forwarding should be set to the IP address of the guest interface (192.168.132.128 in this case) or the gateway address 192.168.132.2 . I have a feeling that I'm missing something very simple here, can anybody tell me what it is?

  Read the article

• Remote Socket Read In Multi-Threaded Application Returns Zero Bytes or EINTR (104)

  - by user39891

  Hi. Am a c-coder for a while now - neither a newbie nor an expert. Now, I have a certain daemoned application in C on a PPC Linux. I use PHP's socket_connect as a client to connect to this service locally. The server uses epoll for multiplexing connections via a Unix socket. A user submitted string is parsed for certain characters/words using strstr() and if found, spawns 4 joinable threads to different websites simultaneously. I use socket, connect, write and read, to interact with the said webservers via TCP on their port 80 in each thread. All connections and writes seems successful. Reads to the webserver sockets fail however, with either (A) all 3 threads seem to hang, and only one thread returns -1 and errno is set to 104. The responding thread takes like 10 minutes - an eternity long:-(. *I read somewhere that the 104 (is EINTR?), which in the network context suggests that ...'the connection was reset by peer'; or (B) 0 bytes from 3 threads, and only 1 of the 4 threads actually returns some data. Isn't the socket read/write thread-safe? I use thread-safe (and reentrant) libc functions such as strtok_r, gethostbyname_r, etc. *I doubt that the said webhosts are actually resetting the connection, because when I run a single-threaded standalone (everything else equal) all things works perfectly right, but of course in series not parallel. There's a second problem too (oops), I can't write back to the client who connect to my epoll-ed Unix socket. My daemon application will hang and hog CPU 100% for ever. Yet nothing is written to the clients end. Am sure the client (a very typical PHP socket application) hasn't closed the connection whenever this is happening - no error(s) detected either. Any ideas? I cannot figure-out whatever is wrong even with Valgrind, GDB or much logging. Kindly help where you can.

  Read the article

< Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >