Search Results

Search found 15646 results on 626 pages for 'port 80'.

Page 169/626 | < Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >

• IRQ problem with 2.6.32/2.6.39 kernel on Debian Squeeze x86_64

  - by MasterM

  I recently assembled a new computer so that all hardware is pretty new. Since then I've been experiencing some problem with IRQs when running Debian 6.0. On random occasions, usually after an hour or so of running I hear a beep and this shows up in dmesg: [ 3537.762795] irq 16: nobody cared (try booting with the "irqpoll" option) [ 3537.762797] Pid: 0, comm: swapper Tainted: P W O 2.6.39-2-amd64 #1 [ 3537.762798] Call Trace: [ 3537.762799] <IRQ> [<ffffffff810924d4>] ? __report_bad_irq+0x3a/0xa2 [ 3537.762803] [<ffffffff810926a4>] ? note_interrupt+0x168/0x1da [ 3537.762805] [<ffffffff81090dd4>] ? handle_irq_event_percpu+0x171/0x18f [ 3537.762807] [<ffffffff8100e0e2>] ? read_tsc+0x5/0x16 [ 3537.762809] [<ffffffff8106b8a2>] ? update_ts_time_stats+0x32/0x6b [ 3537.762810] [<ffffffff81090e26>] ? handle_irq_event+0x34/0x52 [ 3537.762812] [<ffffffff81063fb7>] ? sched_clock_idle_wakeup_event+0x12/0x1c [ 3537.762813] [<ffffffff81092df2>] ? handle_fasteoi_irq+0x82/0xa4 [ 3537.762815] [<ffffffff8100aadb>] ? handle_irq+0x1a/0x23 [ 3537.762816] [<ffffffff8100a384>] ? do_IRQ+0x45/0xaa [ 3537.762818] [<ffffffff81332c93>] ? common_interrupt+0x13/0x13 [ 3537.762818] <EOI> [<ffffffff81332c8e>] ? common_interrupt+0xe/0x13 [ 3537.762821] [<ffffffff81026800>] ? native_safe_halt+0x2/0x3 [ 3537.762829] [<ffffffffa016ed58>] ? acpi_idle_do_entry+0x39/0x62 [processor] [ 3537.762831] [<ffffffffa016edde>] ? acpi_idle_enter_c1+0x5d/0xad [processor] [ 3537.762834] [<ffffffff81261033>] ? cpuidle_idle_call+0x11f/0x1cc [ 3537.762835] [<ffffffff81008dd2>] ? cpu_idle+0xab/0xe1 [ 3537.762837] [<ffffffff8169fc60>] ? start_kernel+0x3e0/0x3eb [ 3537.762838] [<ffffffff8169f3c8>] ? x86_64_start_kernel+0x102/0x10f [ 3537.762839] handlers: [ 3537.762840] [<ffffffffa0358d5a>] (rtl8169_interrupt+0x0/0x2d7 [r8169]) [ 3537.762842] [<ffffffffa08ff2ca>] (nv_kern_isr+0x0/0x54 [nvidia]) [ 3537.762902] Disabling IRQ #16 After that Xorg either hogs on CPU or is unstable (up to hanging the system completely). When I restart Xorg everything is fine again and the problem doesn't occur until next reboot. I tried to upgrade the kernel from stock 2.6.32 to 2.6.39 from unstable repository but that didn't help. Booting with irqpoll option only seems to prolong the initial time period after which the problem occurs. I'm using latest NVIDIA drivers and Realtek firmware from firmware-realtek package. I have two GTX 560Ti that run in SLI. Disabling SLI or taking out one card completely doesn't solve the problem either. Output of uname -a is: Linux whitestar 2.6.39-2-amd64 #1 SMP Wed Jun 8 11:01:04 UTC 2011 x86_64 GNU/Linux Output of lspci is: 00:00.0 Host bridge: Intel Corporation Sandy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root Port (rev 09) 00:01.1 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root Port (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 05) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.2 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 3 (rev b5) 00:1c.4 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 5 (rev b5) 00:1c.6 PCI bridge: Intel Corporation 82801 PCI Bridge (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Cougar Point LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation Device 1200 (rev a1) 01:00.1 Audio device: nVidia Corporation Device 0e0c (rev a1) 02:00.0 VGA compatible controller: nVidia Corporation Device 1200 (rev a1) 02:00.1 Audio device: nVidia Corporation Device 0e0c (rev a1) 04:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) 06:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) 07:00.0 PCI bridge: Device 1b21:1080 (rev 01) 08:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet (rev 10) 08:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) Contents of /proc/interrupts: CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 0: 77 0 0 0 0 0 0 0 IO-APIC-edge timer 1: 2 0 0 0 0 0 0 0 IO-APIC-edge i8042 8: 1 0 0 0 0 0 0 0 IO-APIC-edge rtc0 9: 0 0 0 0 0 0 0 0 IO-APIC-fasteoi acpi 12: 4 0 0 0 0 0 0 0 IO-APIC-edge i8042 16: 699083 0 0 0 0 0 0 0 IO-APIC-fasteoi nvidia, eth0 17: 87810 0 0 0 0 0 0 0 IO-APIC-fasteoi firewire_ohci, hda_intel, nvidia 18: 242 0 0 0 0 0 0 0 IO-APIC-fasteoi hda_intel 23: 85925 0 0 0 0 0 0 0 IO-APIC-fasteoi ehci_hcd:usb5, ehci_hcd:usb6 40: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 41: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 42: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 43: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 44: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 45: 0 0 0 0 0 0 0 0 PCI-MSI-edge PCIe PME 46: 79853 0 0 0 0 0 0 0 PCI-MSI-edge ahci 48: 1 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 49: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 50: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 51: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 52: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 53: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 54: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 55: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 56: 1 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 57: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 58: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 59: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 60: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 61: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 62: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 63: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd 64: 173506 0 0 0 0 0 0 0 PCI-MSI-edge hda_intel NMI: 482 89 25 13 277 24 11 10 Non-maskable interrupts LOC: 783857 194752 114133 70577 372438 179065 117179 162016 Local timer interrupts SPU: 0 0 0 0 0 0 0 0 Spurious interrupts PMI: 482 89 25 13 277 24 11 10 Performance monitoring interrupts IWI: 0 0 0 0 0 0 0 0 IRQ work interrupts RES: 131917 46750 7432 3291 150003 9576 3435 3067 Rescheduling interrupts CAL: 2759 6563 7150 6997 5387 7140 7269 6678 Function call interrupts TLB: 4396 2038 1336 492 5434 1896 1121 606 TLB shootdowns TRM: 0 0 0 0 0 0 0 0 Thermal event interrupts THR: 0 0 0 0 0 0 0 0 Threshold APIC interrupts MCE: 0 0 0 0 0 0 0 0 Machine check exceptions MCP: 37 37 37 37 37 37 37 37 Machine check polls ERR: 0 MIS: 0 Last but not least, right after boot-up those lines are usually present in dmesg: [ 18.367094] hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj. [ 18.458859] hda-intel: IRQ timing workaround is activated for card #2. Suggest a bigger bdl_pos_adj. I'm not sure if it's related or a symptom of a bigger problem so I'm posting it just in case. I don't really know what other information might be of relevance here. Don't hesitate to ask for more in the comments.

  Read the article

• Our embedded linux system won't recognize a USB Device if it is plugged in before powerup. Suggestions?

  - by Blaine

  We are developing on a small embedded device. This device us a gumstix overo board running OpenEmbedded linux. We have our development almost completely done, and have run into the strangest of bugs that we can't figure out. We have a USB Device (Spectrophotometer) that has a USB2.0 Connection and an external power supply for the light source. Typical behavior is that you plug in the power supply, then the USB connection to a host. When the usb connection is detected by the device, the device boots up and enables the light source and fan. The device is then able to be used by the host system. The problem is that if the device is plugged into the Gumstix before we turn on the Gumstix, the USB Device apparently is not probed by the system (and hence does not turn on). Under a normal situation, when the connection is initialized by plugging in the usb cable, the spectro turns itself on and becomes available to the system (this can be seen via "lsusb" typically). Neither of these things are happening. There is no device detected via "lsusb" and no dmesg errors of any kind that we can see. It is as if the device is not plugged in. The device does show up and work fine if we unplug the USB cable and plug it back in once the system is booted up. It turns on and shows up on the usb bus, and we can access it with our driver. On any other desktop or laptop, it does not matter if the host system is on or off when we plug in the spectrometer. This behavior is what I would consider to be "normal" - that the usb system is probed and initialized at boot time, and the usb devices come online. In other words, our system is fully functional as long as we plug in the usb device after the system is booted up. Unfortunately this isn't possible in our final product - everything comes on at once. Additional Info: 1) We have tried a flash drive attached to the system when the system is turned off. Booting up the system brings the flash drive online, as expected 2) There are no messages regarding the spectro or usb device (using dmesg). "lsusb" only lists the USB hubs / controllers. It is literally as if the device is not present and not plugged in. 3) We have tried a brand new image from gumstix and an older image from last year. Both images have this problem. This problem exists on all 3 gumstix devices we use. Does anyone have any suggestions? From what I can tell it isn't really possible to do a complete "reboot" of the usb system that is a complete emulation of "unplugging" and "replugging" a usb device. I feel like what is happening is that there is no initial probe on the usb bus that would trigger the usb handshaking, but this is somehow specific to the spectro. This seems to be a kernel issue or at least an issue in how the kernel is initializing the usb subsystem. I'm not really sure though. I have tried the gumstix mailing list, but there doesn't seem to be anyone who has seen this issue before. Any advice or suggestions on where to start looking would be fantastic. Thank you! Blaine output etc. $ uname -a Linux overo 2.6.33 #1 Tue Apr 27 08:35:38 PDT 2010 armv7l GNU/Linux When the system is up and running and spectro is plugged in (working as intended), this is lsusb: Bus 001 Device 116: ID 2457:1022 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x2457 idProduct 0x1022 bcdDevice 0.02 iManufacturer 1 USB4000 1.01.11 iProduct 2 Ocean Optics USB4000 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 46 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 400mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 4 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) dmesg output: usb usb1: usb auto-resume hub 1-0:1.0: hub_resume usb usb2: usb auto-resume ehci-omap ehci-omap.0: resume root hub hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 hub 2-0:1.0: hub_resume hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000 hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend ehci-omap ehci-omap.0: suspend root hub usb usb2: usb resume ehci-omap ehci-omap.0: resume root hub hub 2-0:1.0: hub_resume ehci-omap ehci-omap.0: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT hub 2-0:1.0: port 2: status 0501 change 0001 hub 2-0:1.0: state 7 ports 3 chg 0004 evt 0000 hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s ehci-omap ehci-omap.0: port 2 high speed ehci-omap ehci-omap.0: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT usb 2-2: new high speed USB device using ehci-omap and address 2 ehci-omap ehci-omap.0: port 2 high speed ehci-omap ehci-omap.0: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT usb 2-2: default language 0x0409 usb 2-2: udev 2, busnum 2, minor = 129 usb 2-2: New USB device found, idVendor=2457, idProduct=1022 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-2: Product: Ocean Optics USB4000 usb 2-2: Manufacturer: USB4000 1.01.11 usb 2-2: uevent usb 2-2: usb_probe_device usb 2-2: configuration #1 chosen from 1 choice usb 2-2: uevent usb 2-2: adding 2-2:1.0 (config #1, interface 0) usb 2-2:1.0: uevent drivers/usb/core/inode.c: creating file '002' dmesg has nothing to say, and lusb simply lists nothing else but the two default usb controllers / hubs if we plug the device in before the system is turned on.

  Read the article

• Fibre channel long distance woes

  - by Marki

  I need a fresh pair of eyes. We're using a 15km fibre optic line across which fibrechannel and 10GbE is multiplexed (passive optical CWDM). For FC we have long distance lasers suitable up to 40km (Skylane SFCxx0404F0D). The multiplexer is limited by the SFPs which can do max. 4Gb fibrechannel. The FC switch is a Brocade 5000 series. The respective wavelengths are 1550,1570,1590 and 1610nm for FC and 1530nm for 10GbE. The problem is the 4GbFC fabrics are almost never clean. Sometimes they are for a while even with a lot of traffic on them. Then they may suddenly start producing errors (RX CRC, RX encoding, RX disparity, ...) even with only marginal traffic on them. I am attaching some error and traffic graphs. Errors are currently in the order of 50-100 errors per 5 minutes when with 1Gb/s traffic. Optics Here is the power output of one port summarized (collected using sfpshow on different switches) SITE-A units=uW (microwatt) SITE-B ********************************************** FAB1 SW1 TX 1234.3 RX 49.1 SW3 1550nm (ko) RX 95.2 TX 1175.6 FAB2 SW2 TX 1422.0 RX 104.6 SW4 1610nm (ok) RX 54.3 TX 1468.4 What I find curious at this point is the asymmetry in the power levels. While SW2 transmits with 1422uW which SW4 receives with 104uW, SW2 only receives the SW4 signal with similar original power only with 54uW. Vice versa for SW1-3. Anyway the SFPs have RX sensitivity down to -18dBm (ca. 20uW) so in any case it should be fine... But nothing is. Some SFPs have been diagnosed as malfunctioning by the manufacturer (the 1550nm ones shown above with "ko"). The 1610nm ones apparently are ok, they have been tested using a traffic generator. The leased line has also been tested more than once. All is within tolerances. I'm awaiting the replacements but for some reason I don't believe it will make things better as the apparently good ones don't produce ZERO errors either. Earlier there was active equipment involved (some kind of 4GFC retimer) before putting the signal on the line. No idea why. That equipment was eliminated because of the problems so we now only have: the long distance laser in the switch, (new) 10m LC-SC monomode cable to the mux (for each fabric), the leased line, the same thing but reversed on the other side of the link. FC switches Here is a port config from the Brocade portcfgshow (it's like that on both sides, obviously) Area Number: 0 Speed Level: 4G Fill Word(On Active) 0(Idle-Idle) Fill Word(Current) 0(Idle-Idle) AL_PA Offset 13: OFF Trunk Port ON Long Distance LS VC Link Init OFF Desired Distance 32 Km Reserved Buffers 70 Locked L_Port OFF Locked G_Port OFF Disabled E_Port OFF Locked E_Port OFF ISL R_RDY Mode OFF RSCN Suppressed OFF Persistent Disable OFF LOS TOV enable OFF NPIV capability ON QOS E_Port OFF Port Auto Disable: OFF Rate Limit OFF EX Port OFF Mirror Port OFF Credit Recovery ON F_Port Buffers OFF Fault Delay: 0(R_A_TOV) NPIV PP Limit: 126 CSCTL mode: OFF Forcing the links to 2GbFC produces no errors, but we bought 4GbFC and we want 4GbFC. I don't know where to look anymore. Any ideas what to try next or how to proceed? If we can't make 4GbFC work reliably I wonder what the people working with 8 or 16 do... I don't assume that "a few errors here and there" are acceptable. Oh and BTW we are in contact with everyone of the manufacturers (FC switch, MUX, SFPs, ...) Except for the SFPs to be changed (some have been changed before) nobody has a clue. Brocade SAN Health says the fabric is ok. MUX, well, it's passive, it's only a prism, nature at it's best. Any shots in the dark? APPENDIX: Answers to your questions @Chopper3: This is the second generation of Brocades exhibiting the problem. Before we had 5000s, now we have 5100s. In the beginning when we still had the active MUX we rented a longdistance laser once to put it into the switch directly in order to make tests for a day, during that day of course it was clean. But as I said, sometimes it's clean just like that. And sometimes it's not. Alternative switches would mean to rebuild the entire SAN with those only to test. Alternative SFPs, well they're hard to come by just like that. @longneck: The line is rented. It's a dark fibre (9um monomode) so there's noone else on it. Sure there are splices. I can't go and look but I have to trust they have been done correctly. As I said the line has been checked and rechecked (using an optical time-domain reflectometer). Obviously you don't have all this equipment yourself because it's way too expensive. @mdpc: What would be the "wrong" type of cable according to you? Up to the switch everything is monomode, yes. The connectors are the correct ones too. Yeah I know there are the green ones where the fibre is cut off at a certain angle etc. But we have the correct ones for all that I know. Progress Report #1 We have had two fabrics (=2x2 switches) with Brocade 5100s with FabricOS 6.4.1 and two fabrics (another 2x4 switches) on FabricOS 7.0.2. On the longdistance ISLs (one in each fabric) it turned out that with FOS 6.4.1 setting it to long distance issues warnings about the VC Init setting and consequently the fill word. But those are only warnings. FOS 7.0.2 requires you to do modifications to VCI and the fillword for long distance links. Setting FOS 6.4.1 to the LS (long-distance static distance) setting with wrong VCI and fillword setting made the whole fabric inoperational (stuck in an SCN loop, use fabriclog -s to see, you don't see it anywhere else, no port error counters or anything increasing). Currently I'm giving the one fabric with the IMHO more correct settings a beating and it seems to do fine, whereas the other one without much traffic still has errors here and there. In short: We have eliminated the active part of the MUX (the FC retimer). We are putting the long distance SFPs into the end equipment themselves. Just to be sure we bought new monomode cables to connect the end equipment to the remaining passive part of the MUX. We are now trying out several long distance configs. It's almost black magic. Everything that happens is mostly empirical, noone seems to have a clue what are the exact reasons to do something. ("We have tried this, and it didn't work, then we tried that and it worked, so we stuck with that." But noone really seems to know why.) I'll keep you updated. Progress Report #2 We got the new lasers for one of the fabrics on warranty. It's ultra clean even on 4GbFC. They're transmitting with roughly 2mW (3dBm) whereas the others are only at 1.5mW (1.5dBm) although that should really be enough. The other fabric (where the lasers are apparently ok) still produces one or two CRCs infrequently. Using sfpshow the SFP producing the actual RX errors shows Status/Ctrl: 0x82 Alarm flags[0,1] = 0x5, 0x40 Warn Flags[0,1] = 0x5, 0x40 Now I'll have to find out what that means. Not sure if it was there before. Well I'll first clear my head with a week of vacation. 8-)

  Read the article

• c#: sms appears to have been sent, but stuck in phone outbox

  - by I__

  i wrote code to send an SMS using my gsm phone which is attached to the computer through com port. the code is below. the problem is i do see that it is in the outbox of the phone and it actually appears to have been sent, but when i contact the recipient they say that i have not received the message. i test the phone, and i create and send a message using only the phone and it works perfectly, however when i do this with my code, it APPEARS to have been sent, and i am getting all the correct AT COMMAND responses from the phone, but the message is actually NOT sent. here is the code: using System; using System.Collections.Generic; using System.ComponentModel; using System.Data; using System.Drawing; using System.Linq; using System.Text; using System.Windows.Forms; using System.Threading; using System.IO.Ports; namespace WindowsFormsApplication1 { public partial class Form1 : Form { SerialPort serialPort1; int m_iTxtMsgState = 0; const int NUM_MESSAGE_STATES = 4; const string RESERVED_COM_1 = "COM1"; const string RESERVED_COM_4 = "COM4"; public Form1() { InitializeComponent(); this.Closing += new CancelEventHandler(Form1_Closing); } private void Form1_Load(object sender, EventArgs e) { serialPort1 = new SerialPort(GetUSBComPort()); if (serialPort1.IsOpen) { serialPort1.Close(); } serialPort1.Open(); //ThreadStart myThreadDelegate = new ThreadStart(ReceiveAndOutput); //Thread myThread = new Thread(myThreadDelegate); //myThread.Start(); this.serialPort1.DataReceived += new SerialDataReceivedEventHandler(sp_DataReceived); } private void Form1_Closing(object sender, System.ComponentModel.CancelEventArgs e) { serialPort1.Close(); } private void SendLine(string sLine) { serialPort1.Write(sLine); sLine = sLine.Replace("\u001A", ""); consoleOut.Text += sLine; } public void DoWork() { ProcessMessageState(); } public void ProcessMessageState() { switch (m_iTxtMsgState) { case 0: m_iTxtMsgState = 1; SendLine("AT\r\n"); //NOTE: SendLine must be the last thing called in all of these! break; case 1: m_iTxtMsgState = 2; SendLine("AT+CMGF=1\r\n"); break; case 2: m_iTxtMsgState = 3; SendLine("AT+CMGW=" + Convert.ToChar(34) + "+9737387467" + Convert.ToChar(34) + "\r\n"); break; case 3: m_iTxtMsgState = 4; SendLine("A simple demo of SMS text messaging." + Convert.ToChar(26)); break; case 4: m_iTxtMsgState = 5; break; case 5: m_iTxtMsgState = NUM_MESSAGE_STATES; break; } } private string GetStoredSMSID() { return null; } /* //i dont think this part does anything private void serialPort1_DataReceived_1(object sender, System.IO.Ports.SerialDataReceivedEventArgs e) { string response = serialPort1.ReadLine(); this.BeginInvoke(new MethodInvoker(() => textBox1.AppendText(response + "\r\n"))); } */ void sp_DataReceived(object sender, SerialDataReceivedEventArgs e) { try { Thread.Sleep(500); char[] msg; msg = new char[613]; int iNumToRead = serialPort1.BytesToRead; serialPort1.Read(msg, 0, iNumToRead); string response = new string(msg); this.BeginInvoke(new MethodInvoker(() => textBox1.AppendText(response + "\r\n"))); serialPort1.DiscardInBuffer(); if (m_iTxtMsgState == 4) { int pos_cmgw = response.IndexOf("+CMGW:"); string cmgw_num = response.Substring(pos_cmgw + 7, 4); SendLine("AT+CMSS=" + cmgw_num + "\r\n"); //stop listening to messages received } if (m_iTxtMsgState < NUM_MESSAGE_STATES) { ProcessMessageState(); } } catch { } } private void button1_Click(object sender, EventArgs e) { m_iTxtMsgState = 0; DoWork(); } private void button2_Click(object sender, EventArgs e) { string[] sPorts = SerialPort.GetPortNames(); foreach (string port in sPorts) { consoleOut.Text += port + "\r\n"; } } private string GetUSBComPort() { string[] sPorts = SerialPort.GetPortNames(); foreach (string port in sPorts) { if (port != RESERVED_COM_1 && port != RESERVED_COM_4) { return port; } } return null; } }

  Read the article

• Dovecot: no auth attempts in 0 secs (IMAP protocol)

  - by Luca D'Amico

  I'm having a lot of problems configuring dovecot ony vps. I'm already able to send email using port 110 and to receive email using port 25, but I can't connect using port 993 and 995. I'm using self-signed ssl certificates. When I try to connect to 993 this error is logged: Jun 8 19:06:39 MY_HOSTNAME dovecot: imap-login: Disconnected (no auth attempts in 2 secs): user=<>, rip=MY_IP, lip=MY_VPS_IP, TLS, session=<MY_SESSION> When I try to connect to 995 here is the error log: Jun 8 19:08:17 MY_HOSTNAME dovecot: pop3-login: Disconnected (no auth attempts in 0 secs): user=<>, rip=MY_IP, lip=MY_VPS_IP, TLS: SSL_read() failed: error:14094416:SSL routines:SSL3_READ_BYTES:sslv3 alert certificate unknown: SSL alert number 46, session=<MY_SESSION> EDIT: I was able to fix this part by refreshing my mail client ssl cert. Anybody can help me please ? I'm stuck :/ Many thanks

  Read the article

• Mac does not recognize wide screen

  - by DUKE

  I am using Mac OS X Lion 10.7.4 on my Mac mini, with Samsung monitor with default resolution 1360 x 768. My Mac mini is connected to Samsung VGA port by Apple mini port to VGA adapter. When starting, my Mac does not recognize the wide screen resolution and always starts in a 4:3 mode, (but it shows 1360x768 as the resolution in the settings). I have to do one of the following actions to bring my Mac to the wide screen resolution: (1) Changing to some other resolution and bring back to the default resolution. (2) Unplug the Apple mini port to VGA adapter and re-connect again. (3) Put the machine to sleep and wake it up again. I am using Ubuntu 12.04, (in a different partition) in the same hardware, but Ubuntu is perfectly recognizing the display.

  Read the article

• What does it mean when ARP shows <incomplete> on eth1

  - by Geoff Dalgas

  We have been using HAProxy along with heartbeat from the Linux-HA project. We are using two linux instances to provide a failover. Each server has with their own public IP and a single IP which is shared between the two using a virtual interface (eth1:1) at IP: 69.59.196.211 The virtual interface (eth1:1) IP 69.59.196.211 is configured as the gateway for the windows servers behind them and we use ip_forwarding to route traffic. We are experiencing an occasional network outage on one of our windows servers behind our linux gateways. HAProxy will detect the server is offline which we can verify by remoting to the failed server and attempting to ping the gateway: Pinging 69.59.196.211 with 32 bytes of data: Reply from 69.59.196.220: Destination host unreachable. Running arp -a on this failed server shows that there is no entry for the gateway address (69.59.196.211): Interface: 69.59.196.220 --- 0xa Internet Address Physical Address Type 69.59.196.161 00-26-88-63-c7-80 dynamic 69.59.196.210 00-15-5d-0a-3e-0e dynamic 69.59.196.212 00-21-5e-4d-45-c9 dynamic 69.59.196.213 00-15-5d-00-b2-0d dynamic 69.59.196.215 00-21-5e-4d-61-1a dynamic 69.59.196.217 00-21-5e-4d-2c-e8 dynamic 69.59.196.219 00-21-5e-4d-38-e5 dynamic 69.59.196.221 00-15-5d-00-b2-0d dynamic 69.59.196.222 00-15-5d-0a-3e-09 dynamic 69.59.196.223 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 225.0.0.1 01-00-5e-00-00-01 static On our linux gateway instances arp -a shows: peak-colo-196-220.peak.org (69.59.196.220) at <incomplete> on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-222.peak.org (69.59.196.222) at 00:15:5d:0a:3e:09 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 Why would arp occasionally set the entry for this failed server as <incomplete>? Should we be defining our arp entries statically? I've always left arp alone since it works 99% of the time, but in this one instance it appears to be failing. Are there any additional troubleshooting steps we can take help resolve this issue? THINGS WE HAVE TRIED I added a static arp entry for testing on one of the linux gateways which still didn't help. root@haproxy2:~# arp -a peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-221.peak.org (69.59.196.221) at 00:15:5d:00:b2:0d [ether] on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 peak-colo-196-220.peak.org (69.59.196.220) at 00:21:5e:4d:30:8d [ether] PERM on eth1 root@haproxy2:~# arp -i eth1 -s 69.59.196.220 00:21:5e:4d:30:8d root@haproxy2:~# ping 69.59.196.220 PING 69.59.196.220 (69.59.196.220) 56(84) bytes of data. --- 69.59.196.220 ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 6006ms Rebooting the windows web server solves this issue temporarily with no other changes to the network but our experience shows this issue will come back. Swapping network cards and switches I noticed the link light on the port of the switch for the failed windows server was running at 100Mb instead of 1Gb on the failed interface. I moved the cable to several other open ports and the link indicated 100Mb for each port that I tried. I also swapped the cable with the same result. I tried changing the properties of the network card in windows and the server locked up and required a hard reset after clicking apply. This windows server has two physical network interfaces so I have swapped the cables and network settings on the two interfaces to see if the problem follows the interface. If the public interface goes down again we will know that it is not an issue with the network card. (We also tried another switch we have on hand, no change) Changing network hardware driver versions We've had the same problem with the latest Broadcom driver, as well as the built-in driver that ships in Windows Server 2008 R2. Replacing network cables As a last ditch effort we remembered another change that occurred was the replacement of all of the patch cords between our servers / switch. We had purchased two sets, one green of lengths 1ft - 3ft for the private interfaces and another set of red cables for the public interfaces. We swapped out all of the public interface patch cables with a different brand and ran our servers without issue for a full week ... aaaaaand then the problem recurred. Disable checksum offload, remove TProxy We also tried disabling TCP/IP checksum offload in the driver, no change. We're now pulling out TProxy and moving to a more traditional x-forwarded-for network arrangement without any fancy IP address rewriting. We'll see if that helps.

  Read the article

• Varnish VCL Reload Fails After Adding Second Backend

  - by Andy

  I have been running Varnish on my production server successfully for several weeks now. Now I'm trying to configure Varnish to use a second backend for certain requests. My original working VCL (/etc/varnish/default.vcl) begins like this: backend default { .host = "127.0.0.1"; .port = "8080"; } ...rest of VCL... And I'm changing it to: backend default { .host = "127.0.0.1"; .port = "8080"; } backend backend2 { .host = "12.34.56.78"; .port = "80"; } ...rest of VCL... When I reload the VCL file, I get the following: Command failed with error code 106 Failed to reload /etc/varnish/default.vcl. Any idea what the error could be, or how I can get more information on the problem?

  Read the article

• Can't get FTP to work on centOS 5.6

  - by josi

  Hi guys I have been trying for a few hours to install and get FTP to work... I did yum install ftp and yum install vsftpd They all installed and are running but when I try to use filezilla or some other client I just can't connect....I've tried connecting on port 21 and port 990 ....nothing! These are my iptables # Firewall configuration written by system-config-securitylevel # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :RH-Firewall-1-INPUT - [0:0] -A INPUT -j RH-Firewall-1-INPUT -A FORWARD -j RH-Firewall-1-INPUT -A RH-Firewall-1-INPUT -i lo -j ACCEPT -A RH-Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A RH-Firewall-1-INPUT -p 50 -j ACCEPT -A RH-Firewall-1-INPUT -p 51 -j ACCEPT -A RH-Firewall-1-INPUT -p esp -j ACCEPT -A RH-Firewall-1-INPUT -p ah -j ACCEPT -A RH-Firewall-1-INPUT -d 224.0.0.251 -p udp -m udp --dport 5353 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 443 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 21 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 25 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 53 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 110 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 990 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 443 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 465 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 646 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 993 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 995 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 3306 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 10009 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 7778 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5000 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 25566 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8765 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8192 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 8123 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 20 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m state --state NEW -m udp --dport 23877 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 9091 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 51413 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 10011 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 30033 -j ACCEPT -A RH-Firewall-1-INPUT -p udp --dport 5353 -d 224.0.0.251 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited COMMIT Any help would be much appreciated! If I do lsof -i :21 without the "." it shows nothing. [root@ks3000420 ~]# lsof -i :21 . COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME bash 9964 root cwd DIR 8,1 4096 483329 . bash 11608 root cwd DIR 8,1 4096 483329 . bash 13550 root cwd DIR 8,1 4096 483329 . vi 14117 root cwd DIR 8,1 4096 483329 . sftp-serv 15261 root cwd DIR 8,1 4096 483329 . sftp-serv 15477 root cwd DIR 8,1 4096 483329 . bash 19074 root cwd DIR 8,1 4096 483329 . lsof 19100 root cwd DIR 8,1 4096 483329 . lsof 19101 root cwd DIR 8,1 4096 483329 .

  Read the article

• Multiple vlan issue with procurve switch

  - by Chris-AZ

  I have a cisco asa5505 as my rtr/fw(10.1.3.254). I have vlan 1 and vlan 3. Vlan 1 is my default all access vlan. Vlan 3 is my Guest(dmz) vlan. I can't seem to get a dhcp ip address when my laptop is plugged into port 42 on my procurve. I have plugged my laptop directly into the firewall and it gets a dhcp ip fine(the firewall is dhcp server). the firewall is plugged into port 41. Only vlan3 needs to go over port 41. I'm sure I have a bonehead config problem however I'm about ready to pull out what little hair I have left. vlan 1 name "Computers" forbid 45 untagged 1-41,43-44 ip helper-address 10.1.1.16 ip address 10.1.1.1 255.255.255.0 tagged 46-48 no untagged 42,45 exit vlan 3 name "Guest Wireless" ip helper-address 10.1.3.254 ip address 10.1.3.1 255.255.255.0 tagged 41-42,44-48 exit

  Read the article

• Lots of TIME_WAIT connections in netstat (Windows Server 2008)

  - by Rhys Causey

  I'm having some issues on a Windows 2008 server with some network connections not going through. For instance, in a web application on the server, we need to open a socket connection to another server, and this fails sometimes with the following message: Only one usage of each socket address (protocol/network address/port) is normally permitted I looked up the error, which led me to this page: http://msdn.microsoft.com/en-us/library/aa560610(v=bts.20).aspx, which indicates that it might be TCP/IP port exhaustion. When I perform netstat -n, I get tons of TIME_WAIT connections on port 80. Does anyone have any idea what could be causing this?

  Read the article

• Isolating VMware virtual machines from the network

  - by jetboy

  I have: VMware Workstation 7 running on a Windows 7 box (with a single NIC), with multiple virtual machines running a range of OSs. The host box is connected to a WRT54G router running Tomato firmware. The router is acting as a wireless bridge to another WRT54G that's wired to my broadband modem. I can access the VMs externally via VNC using VMware's Remote Display. Over time I've had these running: a. Using NAT networking (single IP) with port forwarding on the router and a custom port in VMware for each VM. b. Using bridged networking with static IPs assigned to each VM via MAC address, and port forwarding on the router to each IP running with standard ports. Either way, the host box, and other physical machines on the network are accessible from the VMs. Is there a way to isolate the VMs from the rest of the network, but still maintain internet access and remote VNC to the VMs?

  Read the article

• Unable to connect to Adobe Connect

  - by ub3rst4r

  I am having troubles trying to connect my colleges Adobe Connect. I have done the test meeting connection and it will say "Unable to connect". I have tried connecting on 3 other computers and it works with flying colors. I am running Norton 360 on my computer and I also tried it on my other laptop thats also running Norton 360 and it works on that laptop. I also checked my hosts file and that is not the problem because I am able to connect to the server (on port 80) but not the Adobe Connect port (port 1935). The only thing in it is "127.0.0.1 localhost" Here are the details from the log that the test created: Player Version: WIN 11,3,300,271 App-Server returned: code:ok, servers=rtmp://connect.bowvalleycollege.ca:1935/_rtmp://localhost:8506/,rtmpt://connect.bowvalleycollege.ca:443/_rtmp://localhost:8506/ ERROR: FMS Server did not return correctly! Here is my specifications: Windows 7 SP1 x64 Norton 360 v6.3 (latest) It won't connect in Firefox v15, Chrome v19, or IE9 All of my computers are connected through the same router (D-Link DIR-625) Any ideas?

  Read the article

• WinXP How to Tunnel LPT over USB

  - by Michael Pruitt

  I have a windows program that accesses a device connected to a LPT (1-3) 25 pin port. The communication is bidirectional, and I suspected the control lines are also accessed directly. I would like to migrate the device to a machine that does not have a LPT port. I saw the dos2usb software, but that takes the output (from a DOS program) and 'prints' it formatted for a specific printer. I need a raw LPT connection, and a cable that provides access to all the control signals. I do have a USB to 36-pin Centronics that may have the extra signals. I use it with a vinyl cutter that doesn't like most of the USB dongles. It comes up as USB001. Would adding and sharing a generic printer, then mapping LPT1 to the share get me closer? Would that work for a parallel port scanner? My preferred solution is a USB cable with a driver that will map it to LPT1, LPT2, or LPT3.

  Read the article

• Uninstall last n of ports/packages

  - by Radio

  While compiling some port, I realized that it depends on 1000+ of other ports and will install forever until I die or my disk is full (my hdd is really small). I interrupted make install clean. How do I uninstall and clean those dependencies which have already been built and installed? (there are at least 100+ of them) pkg_cutleaves wont work in this case, since the main port wasn't registered yet. Please help. FreeBSD 9.0-RELEASE amd64 EDIT: Another way to ask this question: How can I see all dependencies for a non-registered port, and all subdependencies for those dependencies, independent with previously installed ports or their [sub]dependencies?

  Read the article

• Multiple home routers

  - by netvope

  Suppose I have the following configuration: Router A: WAN port connected to the Internet, LAN = 192.168.1.0/24 Computer A: Connected to router A as 192.168.1.101 Router B: WAN port connected to router A as 192.168.1.102, LAN = 192.168.2.0/24 Computer B: Connected to router B as 192.168.2.101 Now I want computer A to communicate with computer B seamlessly (e.g. can establish a TCP connection by running nc 192.168.2.101 <port>) by means of routing, rather than merging the two networks into one (which can be easily accomplished using router B as a switch). Most routers are shipped with NAT turned on, of which I definitely need to turn off in router B. But what other steps do I need to take so that packets from computer A to computer B would go through router B? I could manually add a routing table entry in computer A so that all packets targeted to 192.168.2.0/24 go through gateway 192.168.1.102, but I would prefer an automatic way if it exist.

  Read the article

• Multiple home routers

  - by netvope

  Suppose I have the following configuration: Router A: WAN port connected to the Internet, LAN = 192.168.1.0/24 Computer A: Connected to router A as 192.168.1.101 Router B: WAN port connected to router A as 192.168.1.102, LAN = 192.168.2.0/24 Computer B: Connected to router B as 192.168.2.101 Now I want computer A to communicate with computer B seamlessly (e.g. can establish a TCP connection by running nc 192.168.2.101 <port>) by means of routing, rather than merging the two networks into one (which can be easily accomplished using router B as a switch). Most routers are shipped with NAT turned on, of which I definitely need to turn off in router B. But what other steps do I need to take so that packets from computer A to computer B would go through router B? I could manually add a routing table entry in computer A so that all packets targeted to 192.168.2.0/24 go through gateway 192.168.1.102, but I would prefer an automatic way if it exist.

  Read the article

• Amazon EC2 SSH Failed to connect "Bad File Number"

  - by Mark McCook

  This is the command I am told to use by clicking connect in the control panel "ssh -i private_key.pem root@instancePublicDNS" Well that one failed so I wanted to know what happen so I ran "ssh -vvv private_key.pem root@instancePublicDNS" OpenSSH_4.6p1, OpenSSL 0.9.8e 23 Feb 2007 debug2: ssh_connect: needpriv 0 debug1: Connecting to private_key.pem [...] port 22. debug1: connect to address ... port 22: Attempt to connect timed out without establishing a connection ssh: connect to host private_key.pem port 22: Bad file number Any Ideas? I have searched for the answer on google and serverfault, I found a few possible solutions that did not work. info about the instance AMI-ID : ami-688c7801 ( ubuntu 10.10 Server )

  Read the article

• How do I tell sudo to write files with a umask of 0022?

  - by mipadi

  I recently upgrading to Snow Leopard. I have noticed that some files written by MacPorts are installed with the wrong permission -- they are written with a umask of 0077. I think I have narrowed down the problem: The port command is invoked via sudo. My .bashrc file specifies a umask of 0077. On older versions of OS X (10.5 and below), sudo used the umask of the root user (which was 0022); however, now it uses my umask of 0077. Is there anyway to have sudo use the old behavior? Right now, it's kind of annoying because I have to use sudo to run simple commands like port installed, port outdated, etc. (The problem is described in more detail in this MacPorts ticket.) Edit I discovered the umask option for sudo, and in /etc/sudoers I added the following line: Defaults umask=0022 However, this did not function as desired, because the real umask used by sudo is the union of the user mask with this default mask.

  Read the article

• Network wide rule to forwared IP address

  - by Patrick

  Hi, we have a virtual machine which hosts a web based bug tracker in our network which is reached internally via e.g. 192.168.1.5:9800. From the outside we made a port forwarding in our firewall so that the web site can be reached via e.g. 72.10.10.10:9800. Now that works fine but the problem is that we got different IP addresses to reach the same service depending if we are in the office or at home and when the service sends out an email the link doesn't always work :) So we are looking for a solution to fix it. One could be to make a rule in out firewall that all communication to 72.10.10.10:9800 is forwarded to 192.168.1.5:9800... If that's possible that is considering it's an IP address + a port. The reason we used a port is because we only got one static public IP address but multiple virtual web appliances. Thanks for any suggestions or solutions :) Patrick PS: The network is a Win 2008 R2 domain by the way

  Read the article

• Remote servlet by mod_jk ?

  - by marioosh.net

  I have remote servlet for example: h*tps://[ip_address]/servlet (h*tps://[ip_address]/ - Tomcat main page) that i need to configure on local Apache HTTPd server. My mod_jk configuration looks like below, but doesn't work. Something works, because when i type h*tps://localhost/console in a browser i get Tomcat error page "HTTP Status 404 - /console/". JkWorkersFile /etc/apache2/workers.properties JkLogFile /var/log/apache2/mod_jk.log JkLogLevel info JkMount /console/* ajp13 workers.properties: worker.ajp13.type=ajp13 worker.ajp13.host=[ip_address] worker.ajp13.port=8009 Remote Tomcat is configured good i think - listen on port 8009 and servlet h*tps://[ip_address]/servlet works too. <Connector port="8009" protocol="AJP/1.3" redirectPort="443" /> Anybody helps ?

  Read the article

• SFTP is not connecting to remote server

  - by Crono15

  $ sftp -vvv Remote_IP Connecting to Remote_IP... OpenSSH_5.2p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug2: ssh_connect: needpriv 0 debug1: Connecting to Remote_IP [Remote_IP] port 22. debug1: connect to address Remote_IP port 22: Operation timed out ssh: connect to host Remote_IP port 22: Operation timed out Connection closed I set up an account for SFTP only access with a chroot. I tested that on the server and it works fine. The problem is, I could not get remote SFTP access to the server to work right. The example above is what I keep on running into. I have been trying to figure out how to solve this problem for 2 days now. I am not sure if it have to do with /etc/ssh/sshd_config. Is it something that I am not aware of? I am hoping that you could help point me to the right place for this issue.

  Read the article

• Nginx .zip files return 404

  - by Kenley Tomlin

  I have set up Nginx as a reverse proxy for Node and to serve my static files and user uploaded images. Everything is working beautifully except that I can't understand why Nginx can't find my .zip files. Here is my nginx.conf. user nginx; worker_processes 1; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include mime.types; proxy_cache_path /var/www/web_cache levels=1:2 keys_zone=ooparoopaweb_cache:8m max_size=1000m inactive=600m; sendfile on; upstream *******_node { server 172.27.198.66:8888 max_fails=3 fail_timeout=20s; #fair weight_mode=idle no_rr } upstream ******_json_node { server 172.27.176.57:3300 max_fails=3 fail_timeout=20s; } server { #REDIRECT ALL HTTP REQUESTS FOR FRONT-END SITE TO HTTPS listen 80; server_name *******.com www.******.com; return 301 https://$host$request_uri; } server { #MOBILE APPLICATION PROXY TO NODE JSON listen 3300 ssl; ssl_certificate /*****/*******/json_ssl/server.crt; ssl_certificate_key /*****/******/json_ssl/server.key; server_name json.*******.com; location / { proxy_pass http://******_json_node; proxy_redirect off; proxy_set_header Host $host ; proxy_set_header X-Real-IP $remote_addr ; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for ; proxy_set_header X-Forwarded-Proto https; client_max_body_size 20m; client_body_buffer_size 128k; proxy_connect_timeout 90s; proxy_send_timeout 90s; proxy_read_timeout 90s; proxy_buffers 32 4k; } } server { #******.COM FRONT-END SITE PROXY TO NODE WEB SERVER listen 443 ssl; ssl_certificate /***/***/web_ssl/********.crt; ssl_certificate_key /****/*****/web_ssl/myserver.key; server_name mydomain.com www.mydomain.com; add_header Strict-Transport-Security max-age=500; location / { gzip on; gzip_types text/html text/css application/json application/x-javascript; proxy_pass http://mydomain_node; proxy_redirect off; proxy_set_header Host $host ; proxy_set_header X-Real-IP $remote_addr ; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for ; proxy_set_header X-Forwarded-Proto https; client_max_body_size 20m; client_body_buffer_size 128k; proxy_connect_timeout 90s; proxy_send_timeout 90s; proxy_read_timeout 90s; proxy_buffers 32 4k; } } server { #ADMIN SITE PROXY TO NODE BACK-END listen 80; server_name admin.mydomain.com; location / { proxy_pass http://mydomain_node; proxy_redirect off; proxy_set_header Host $host ; proxy_set_header X-Real-IP $remote_addr ; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for ; client_max_body_size 20m; client_body_buffer_size 128k; proxy_connect_timeout 90s; proxy_send_timeout 90s; proxy_read_timeout 90s; proxy_buffers 32 4k; } } server { # SERVES STATIC FILES listen 80; listen 443 ssl; ssl_certificate /**/*****/server.crt; ssl_certificate_key /****/******/server.key; server_name static.domain.com; access_log static.domain.access.log; root /var/www/mystatic/; location ~*\.(jpeg|jpg|png|ico)$ { gzip on; gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/rss+xml text/javascript image/svg+xml application/vnd.ms-fontobject application/x-font-ttf font/opentype image/png image/jpeg application/zip; expires 10d; add_header Cache-Control public; } location ~*\.zip { #internal; add_header Content-Type "application/zip"; add_header Content-Disposition "attachment; filename=gamezip.zip"; } } } include tcp.conf; Tcp.conf contains settings that allow Nginx to proxy websockets. I don't believe anything contained within it is relevant to this question. I also want to add that I want the zip files to be a forced download.

  Read the article

• I need access control within the same network/VLAN

  - by Sadiq ali

  Hi, I have a single network/VLAN and I want to block some traffic and allow some traffic in my network, is this possible using a L2 or L3 switch? If so which switches support this feature and what would be the commands to configure this? I have already tried this using access lists by applying it to an ethernet port but if I apply it on one port it will automatically work on incoming traffic on that port but I mean it to work on only outgoing traffic as per my ACL. Do you have any suggestions please?

  Read the article

• VMware networking - PortChannel or not?

  - by dunxd

  My ESX hosts each have 8 NICS. I have set up 2 NICs for our iSCSI SAN - each is connected to a different SAN switch. 2 NICs are set up for vMotion and Service Console - these are each connected to a different core switch (ports are trunked with VLANs dedicated to vMotion and Management) I now have four ports left over. Currently we have these set up each going into our default VLAN. Two NICs are connected to one core-switch and two are connected to the other. We decided to aggregate the connections to each switch - so they are teamed at the vswitch end, and port channelled at the physical switch end. I am now reading that port channelling these connections is not particularly useful, perhaps even over complicating things. Is there a particular problem with using port channels for VMware? What method provides the best balance between redundancy and performance?

  Read the article

< Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >