Search Results

Search found 2962 results on 119 pages for 'cisco vpn'.

Page 17/119 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

  • QoS basics on a Cisco ASA

    - by qbn
    Could someone briefly explain how to use QoS on Cisco ASA 5505? I have the basics of policing down, but what about shaping and priorities? Basically what I'm trying to do is carve out some bandwidth for my VPN subnets (in an object-group called priority-traffic). I've seen this Cisco QoS document, however configuring shaping and priority-queue don't seem to have any effects in my test. A full download of the linux kernel from kernel.org will boost a ping to a server via VPN sky high. Policing has been successful in passing this test, although it doesn't seem as efficient (I cap non-vpn traffic at 3 of my 4.5 megabits of bandwidth). Am I misunderstanding the results of the test? I think there is some simple concept I'm not grasping here. EDIT: Here is my config thus far (I have 4.5 megabits of bandwidth): access-list priority-traffic extended permit ip object-group priority-traffic any access-list priority-traffic extended permit ip any object-group priority-traffic access-list priority-traffic extended permit icmp object-group priority-traffic any access-list priority-traffic extended permit icmp any object-group priority-traffic access-list non-priority-traffic extended deny ip object-group priority-traffic any access-list non-priority-traffic extended deny ip any object-group priority-traffic access-list non-priority-traffic extended permit ip any any priority-queue outside queue-limit 440 class-map non-priority-traffic match access-list non-priority-traffic class-map priority-traffic match access-list priority-traffic class-map inspection_default match default-inspection-traffic policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp policy-map outbound-qos-policy class non-priority-traffic police input 2500000 police output 2500000 class priority-traffic priority service-policy global_policy global service-policy outbound-qos-policy interface outside

    Read the article

  • Problems with ipsec betwen Cisco ASA 5505 and Juniper ssg5

    - by Oskar Kjellin
    I am trying to set up an ipsec tunnel between our ASA 5505 and a Juniper ssg5. The tunnel is up and running, but I cannot get any data through it. The local network I am on is 172.16.1.0 and the remote is 192.168.70.0. But I cannot ping anything on their netowork. I receive a "Phase 2 OK" when I set up the ipsec. I think this is the part of the config that is applicable. It seems like the data is not routed through the tunnel, but I am not sure... object network our-network subnet 172.16.1.0 255.255.255.0 object network their-network subnet 192.168.70.0 255.255.255.0 access-list outside_cryptomap extended permit ip object our-network object their-network crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 1 match address outside_cryptomap crypto map outside_map 1 set pfs crypto map outside_map 1 set peer THEIR_IP crypto map outside_map 1 set ikev1 phase1-mode aggressive crypto map outside_map 1 set ikev1 transform-set ESP-3DES-MD5 crypto map outside_map 1 set ikev2 pre-shared-key ***** crypto map outside_map 1 set reverse-route crypto map outside_map interface outside webvpn group-policy GroupPolicy_THEIR_IP internal group-policy GroupPolicy_THEIR_IP attributes vpn-filter value outside_cryptomap ipv6-vpn-filter none vpn-tunnel-protocol ikev1 tunnel-group THEIR_IP type ipsec-l2l tunnel-group THEIR_IP general-attributes default-group-policy GroupPolicy_THEIR_IP tunnel-group THEIR_IP ipsec-attributes ikev1 pre-shared-key ***** ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key *****

    Read the article

  • linksys wrt54g router to a Cisco router?

    - by jasondavis
    This may be a strange question but I have no clue. I currently have a basic linksys wrt54g router fo9r my home network. I am considering getting a rack/cabinet and running a home server or 2 and hooking up my home network to it. If I were to do0 this I could pick up a cisco rack mounted router and switch off ebay to use. So If I were to do this, would I just plugin in the cables for the cisco router from my dsl modem or is there more to it to get these working?

    Read the article

  • DHCP Relay V DHCP Local Cisco v 3com

    - by DefSol
    Howdy, I have a client who has a WAN with 7 sites. At one site in particular, randomly about 4-5 clients do not get an IP address. The local gateway is a cisco 871 and relay's to a windows server in a Data Center running a valid scope for the subnet. If I put in a cisco 1800 and configure a dhcp scope (disabling the scope on the server) all clients get an ip address and everything is right with the world. The Wan providing keeps saying it's a local issue although we can work around with the 1800. The provider says a 3Com switch is at fault and the 1800 does not have a local switch, and because the 871 does, means the internal switching will receive a different uplink policy. The 3Com is the only managed switch in the subnet. Any ideas greatly appreciated. Reuben

    Read the article

  • VPN with wrong subnet mask

    - by Philipp Schmid
    I followed these instructions on www.hottonetworking.com to set up VPN on a clean install of Windows Server 2008 SP2 (not R2 yet). When I then establish a VPN connection to that machine from a client machine (running Windows 7 RC), everything succeeds (it seems since I get a 'Connected' state in the network sharing center window), but I end up with a subnet mask (according to ipconfig /all) of 255.255.255.255 instead of 255.255.255.0. The net effect is that I don't have local network or internet capability. What additional configuration steps do I have to do to get VPN with the proper subnet mask working? Update: Using the steps outlined in the Technet article mentioned by Mr. Nimble, I was able to get internet connection. Apparently the subnet mask is not an issue as my coworker was able to connect using his VPN connection and ping the server machine by name as well.

    Read the article

  • Can connect through Watchguard mobile VPN, but can't ping or access network drives

    - by johnnyb10
    We're having any issue in which some of our employess can no longer connect to our network drives when out of the office. We use Watchguard Mobile VPN (we have a Watchguard Firebox firewall) and the users are able to connect. That is, their status in the the VPN client says "Connected" and they have the correct IP address listed as the VPN Endpoint. The problem is, when they try to map drives, or even ping the IP address of a server on our network, it fails. Last week, we temporarily switched one of our Comcast modems to our backup DSL modem because the Comcast was accidentally shut off by Comcast, and the problem seemed to start around then. We've since switched back and the problem persists, so that doesn't seem to have been it (which makes sense). But we also made other changes at the time that might have thrown something off, although we feel like we've checked them all. Plus, some people can successfully connect to network drives through the VPN. Can someone please suggest some steps to help troubleshoot? We've checked the policies on our Watchguard box, and they seem fine. We've looked at the settings on the Mobile VPN client, but nothing seems like a probable cause. Thanks.

    Read the article

  • Fortinet SSL VPN Client Setup Without GUI on Linux (centos)

    - by Calua
    How can I install and setup a fortinet SSL VPN client on a VPS that's running on Centos? I have problem to do it because all guide I have are all using GUI which is not installed on the VPS to save resource. (example: http://dbssolutions.freshdesk.com/solution/categories/1513/folders/3047/articles/1791-how-to-install-the-linux-fortinet-ssl-vpn-client) I already have the linux version for the vpn client but not sure how to install and configure it only using the terminal.

    Read the article

  • Watchguard box VPN Access X700

    - by Paulio001
    We have a watchguard X700 box that we are trying to get VPN access through. We have had a play with the ports and tried to open the VPN access but still have no joy. Do we need to purchase a special licence to get VPN open on this box?

    Read the article

  • Cisco Catalyst 65XX and traffic shaping

    - by Nadz Goldman
    Hello! I have Cisco Catalyst 65XX, many VLANs and about ~1300 users. Users connected to some D-Link switches with second-level management. D-Link switches come to my Cisco Catalyst 65XX by VLANs. So, how I can shape traffic per user? If I use something like this: access-list 145 permit ip any host 192.168.0.1 access-list 145 permit ip any host 192.168.0.2 access-list 145 permit ip any host 192.168.0.3 ... int Gi0/1 traffic-shape group 145 128000 7936 7936 1000 will I have shape traffic per user or it will shape traffic only on interface? I mean - every user will have 128kb/s (per user) or everybody will have 128kb/s ? If it will be for everybody, then what is the solution of my question: how every user can have 128kb/s ?

    Read the article

  • screen resume works on top of VPN

    - by michael
    I connect to my network using VPN. I have screen running and 'ssh' to a server. I then kill my shell and I was able to 'resume' by 'screen -r'. This works as expect. But when I disconnect VPN and re-connect VPN, and type 'screen -r' again. I was not able to get my last screen again. And I see "Write failed: Connection reset by peer46.11 MiB | 642 KiB/s" in the screen. Can you please tell me if it possible to reconnect 'screen' if my VPN is disconnect. Thank you.

    Read the article

  • Restrict VPN client traffic to certain domains/IP

    - by mr-euro
    Hi Is there any way to restrict a VPN client to only route certain traffic via the VPN and the rest via their local gateway? For example: traffic to a certain IP or domain gets routed across the VPN and all other requests do not. Let me know if you need more details. Thank you.

    Read the article

  • iPhone Remote with iTunes Library via VPN

    - by sudo work
    Alright, so I'm currently behind a network router (not under my control). The router performs NAT and somehow prevents a computer from scanning other nodes. At least, you're unable, in this instance, to locate an iTunes library. You can, however, communicate with a node's open ports if the local IP address is known, as well as the port. I haven't actually tried port scanning a specific IP using nmap or another tool yet. So I've tried one solution to remove the contribution of the router entirely (to verify that it works without the influence of the routers). I set up an access point using my iPhone and tethered my computer (with the library) to it. From here, I was able to pair my library and the iPhone Remote application. Control of the library was normal as well. This solution is not ideal, however, because I am actively using bandwidth with my computer and cannot afford to be tethered to my 3G connection. A viable solution for me is to use a common VPN connection, which I have set up on a Ubuntu (Intrepid) server that is remote. Both my computer and iPhone are able to access the VPN via PPTP. The server is setup with PPTPD as the VPN-server; I'm using IPTables to perform IP masquerading and forwarding traffic. I however, still cannot connect the library to the phone. I can however, see both devices on the VPN subnet (192.168.0.0/24). SSH'ing and such works fine. What settings on the VPN server must I change to get this to work? Also, how can I assign static IP addresses to various PPTP clients based on MAC addresses?

    Read the article

  • Connecting to VPN via Proxy

    - by Rodrigo
    Hi, My company's VPN server is located in Netherlands, from my current location this is a really crappy place in terms of connectivity, connection keeps dropping, it's slow and keeps being reset during high traffic times. I have a dedicated server over USA which is able to connect to VPN server without this issues, connection is stable and fast. My question is, how do I connect to this VPN using a proxy running on my dedicated server? I'm on Windows 7 using a VM on XP to connect to the VPN. Thanks.

    Read the article

  • VPN connection sharing for Ubuntu guest

    - by pzico
    I have Ubuntu 10.04 guest on Windows XP host. I need to use a specific VPN software that works only on Windows. How should I configure virtualbox/guest so that the VPN connection would be visible on guest? I already tried NAT and bridged network settings. With both of these options I get only normal internet connection to work, but sites requiring VPN don't work on guest, only on host.

    Read the article

  • How to connect with a vpn connection without any prompt in windows 8

    - by saber tabatabaee yazdi
    In windows 7 , we can define a hotkey for connect to internet via VPN connection immediately without any prompt, through these Steps: Create shortcut for VPN connection for example in Desktop. Define a hotkey for that shortcut In VPN properties options TAB dialing options uncheck this checkbox : "prompt for name and password..." This checkbox not exist in windows 8 so we cant define in Windows 8 like that.

    Read the article

  • Gre Tunnel Cisco Linux traffic forwarding

    - by mezgani
    I setup a gre tunnel a cisco router and a Linux machine, the tunnel interface in the Linux box named pic. Well i have to forward traffic coming from cisco through the Linux box. the rules i've set in the Linux box is described as follow: echo "1" /proc/sys/net/ipv4/ip_forward iptables -A INPUT -p 47 -j ACCEPT iptables -A FORWARD -i ppp0 -j ACCEPT iptables -A FORWARD -i pic -o ppp0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i ppp0 -o pic -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE I see the traffic coming from tunnel and forwarded to internet but no reply from sent packet. May i miss something like a routing rule.

    Read the article

  • IIS8 behind a VPN + Windows Server 2012 - how to properly bind IP+Port

    - by ryugen
    This is my first question so I hope I'm going to give you enough information. I'm running Windows Server 2012 within the Hyper-V environment of my Windows 8 machine. Within Windows Server 2012 I'm running a VPN tool based on openVPN to hide my real IP. When I run IIS8 with the VPN disconnected it works flawlessly through the Internet (port 80 forwarded correctly). But as soon as I connect to the VPN I can't reach my site through the domain anymore. Now I tried basically everything I know which is why I'm asking you guys. I tried binding IIS8 to the IP of my virtual ethernet card. I tried changing the priority of the NIC through the "Network and sharing center" via the advanced tab. I used ipconfig /flushdns in case there was something wrong in the DNS handling. Hell, I even turned off the Windows firewall. I also used a port scanner to verify the problem. The webserver is reachable on port 80 with VPN disconnected and immediately gets unreachable on connect. Theoretically both IPs (my regular one AND the VPN) should be reachable or at least not impair the other one right? Do you have any other suggestion? Do I have to route something somewhere somehow?

    Read the article

  • Setting up a vpn and IIS IP address restrictions

    - by carpat
    I'm trying to get a VPN set up with internal access only sites. I have set up a VPN on a windows server (single VPS server), and I can connect from a remote computer and I get an IP assigned correctly (from 192.168.1.1 - 255) Next I configured IIS (running on the same machine) IP Address and Domain Restrictions to only allow only IP address range 192.168.1.0 with subnet mask 255.255.255.0 When I connect to the VPN with "Use Default Gateway on Remote Network" (so that requests must go through the vpn), I get a 403 from the internal sites. What did I miss?

    Read the article

  • Smart card authentication to a Cisco switch?

    - by murisonc
    We have our Cisco network devices configured to authenticate network administrators using their domain accounts via RADIUS running on a Windows 2008R2 server with the network protection role. This works great for logging into the switch via SSH when configuring the devices. We are now in the beginning stages of deploying smart cards for logins. Does anyone know of a way to login to a Cisco switch using a smart card instead of a domain username and password? The SSH client we are using is Putty. Workstations are Windows 7. RADIUS is running on Windows 2008R2. We are running our own certificate authority on Windows 2008; network is not connected to the Internet. We prefer to not have to purchase additional proprietary devices for this functionality.

    Read the article

  • Connect iPad to windows 7 VPN

    - by Linuz
    My iPad keeps spitting out the error: "A connection could not be established to the PPP server." I am trying to connect it to a VPN I set up with Windows 7 as an incoming connection. On the iPad, I went into the VPN settings, added a new PPTP VPN with the following information Server: Windows 7 Computer's IP RSA SecurID: OFF Account: Account Username Password: Account Password Encryption Level: Auto Send All Traffic: ON Proxy: Off Now I know that it is making some connection to the Windows 7 Computer because whenever I intentionally put in the wrong VPN password on the iPad, it makes me put in the correct one before trying to connect again. All the ports are forwarded on my router for PPTP, and my Windows 7 Firewall is even off to try to get this to work. Any help would be greatly appreciated, thanks.

    Read the article

  • No External Network Access Through Ubuntu VPN

    - by trobrock
    I have setup pptpd as my VPN server on Ubuntu Server 9.04, I am able to connect to the VPN from the client and can access the server's local network, but I am unable to connect to the external network via the VPN. If I login to the server via SSH: $ ping google.com PING google.com (74.125.67.100) 56(84) bytes of data. 64 bytes from gw-in-f100.google.com (74.125.67.100): icmp_seq=1 ttl=49 time=65.9 ms 64 bytes from gw-in-f100.google.com (74.125.67.100): icmp_seq=2 ttl=49 time=63.2 ms 64 bytes from gw-in-f100.google.com (74.125.67.100): icmp_seq=3 ttl=49 time=63.9 ms 64 bytes from gw-in-f100.google.com (74.125.67.100): icmp_seq=4 ttl=49 time=66.0 ms If I connect to the VPN and ping locally: $ ping google.com ping: cannot resolve google.com: Unknown host I have a feeling it is some routing issue on the server but I am unsure.

    Read the article

  • Netgear FVS336G as VPN Server

    - by Farseeker
    Hi All, One of our offices has made the move away from PFSense to a Netgear FVS336G. The one feature I can't seem to figure out is its VPN capabilities. I'm confused as to whether this device can act as a IPSEC VPN server, or if it can only act as the client in a Site-Site VPN. The documentation does not make this clear at all, and Google does not seem to have been any help. (Related question: here)

    Read the article

  • Change the order of DNS lookup when connected in the VPN

    - by qwerty2010
    Using Windows 7 Pro here. I have my LAN network adapter with DNS server 8.8.8.8 (Google's DNS). I also have OpenVPN client to connect to my company's network. If I type "nslookup" while disconnected from the VPN, I get 8.8.8.8 (from my LAN network adapter). If I type "nslookup" while connected in the VPN, I get the DNS IP from my company's network. That makes me think that when connected to the VPN all DNS's resolution are routed first to my company's DNS. How can I change this order, and make the DNS resolution be routed to 8.8.8.8 first, when I'm connected to the VPN? Thank you

    Read the article

  • Log internet requests made by vpn client

    - by Adam Schiavone
    How can I log the requests that people make to the internet when they are connected to my VPN? If one of them does something illegal, I need to be able to prove that it was not me, but a VPN client. This really is a just in case type thing. So, I want to be able to see the details (server, port, domain name, and time connected) in a file somewhere. Does windows offer this with its PPTP VPN service, or is there 3rd party software to do this (Free is better)? EDIT I have setup accounting, but that does not seem to tell me what I am looking for. Could someone comment on what accounting does? EDIT 2 Maybe I should heve been clearer. My system is running windows server 2008 r2 and using the stock VPN software (PPTP)

    Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >