Search Results

Search found 57910 results on 2317 pages for 'html form post'.

Page 17/2317 | < Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >

• Gateway GT5220 Boot/POST Failure

  - by John Rudy

  I have a Gateway GT5220 I'm troubleshooting. It is, in fact, the machine I just gave my father for his birthday a couple months ago. (Prior to that, it was my home PC. My home PC is now the MacBook on which I'm writing this.) Before going any further, I suspect that the answer will be, "It's worse than that, it's dead, Jim, it's dead, Jim, it's dead, Jim." At least, mobo and/or CPU. The initial symptoms were as follows: Turn on power All fans fire up (thus making it so I can't hear if the hard drive is spinning or not, nor are my hands sensitive enough anymore to feel it) No LEDs remained lit on the front panel. (Initially, the hard drive indicator flashed briefly.) No beep, no video, no nothing. Following some advice I found here, I tried to "drain the stored power." After following those steps, the new symptoms were: Turn on power All fans fire up The front panel LEDs remained lit! After about 20, maybe 30 seconds, we had video! Sort of. We got to the Gateway splash/POST screen, which appeared thoroughly corrupted. How corrupted? Well, I imagine it's what a POST screen would look like after reading the wrong passage out of the Necronomicon: It stayed there. I gave it at least 5, maybe 6 minutes, and it didn't move. So I shut her down, started her up again, and now (this is where we currently stand, symptomatically) we have this: Turn on power All fans fire up The front panel LEDs remain lit No video, no beep, no nothing. I'm a software guy; haven't done real hardware troubleshooting in years. My gut tells me that the mobo and/or CPU is fried, and unfortunately my gut didn't get to be as big as it is being wrong all the time. :( In addition to the link above, I have read all of the following (trying to save you some LMGTFY trouble): Gateway Support POST Error Messages and Handling About a zillion (useless) POST beep code sites A kioskea.net post indicating that most likely we're at what I consider "total loss" (mobo and/or CPU) My questions: Are there any conditions other than mobo/CPU that could cause symptoms like these? Is it worth my time to try the next hardware troubleshooting step?(IE, remove all non-critical hardware from the machine, try to boot, systematically replace one by one until we find the failing component) Which mobos will fit in the Gateway GT5220 case (with rear ports correctly aligned)? (Why this is not a dupe: I wouldn't have posted this question if it hadn't been for the funkadelic possessed video display on the one occasion we got video out. I think that justified this not being an exact dupe. Of course, if the community overrules, I will understand.)

  Read the article

• PC will POST whenever feels likes it

  - by kyrpas

  I'm really sick of my PC and I'd love to throw it off the 5th floor but unfortunately I don't have this luxury right now. The issues started when I moved to a new house about 2 months ago. I didn't have this problem before. Case: Arctic Cooling Silentium T1 with embedded Fusion 550 Eco 80 PSU. M/B: ASRock A790GMH/128M Gfx: ATI Radeon HD 5770 Here's what's happening almost on a daily basis: I wake up in the morning, switch on the PC and all the fans start spinning. 9/10 the graphics fan stays on 100% and I know it won't post. If I'm lucky, ATI's fan stays on full power for a second, then goes back to normal and I get a normal post but that doesn't happen often. No, instead it's just drives me crazy. When I get no POST I'm trying a lot of different things and what bothers me the most is that they all work. But not always. No... That way I could find out what the hell is going on and we don't want that.. right? So, sometimes it manages to POST if I: remove the keyboard remove the power cable for a few minutes remove the graphics card remove the HDD cables do nothing, just turn it on and off a few times Sometimes it doesn't POST even if I do all of the above. And I end up removing all power cables from the M/B, and connecting all the stuff one by one. Sometimes it works, sometimes it doesn't and I just have to pray and wait. What the hell is that? I'm getting pissed of again just thinking about it. The only solution is to leave it on 24/7 but I don't want to do that. It should be able to turn on and off when I press the power button. I'm not asking much. I'm starting to think there's some weird electricity/power issue but I really don't understand what it is. There's no logical explanation about it. At least I can't find one. Any ideas?

  Read the article

• nginx proxy_pass POST 404 errors

  - by Scott

  I have nginx proxying to an app server, with the following configuration: location /app/ { # send to app server without the /app qualifier rewrite /app/(.*)$ /$1 break; proxy_set_header Host $http_host; proxy_pass http://localhost:9001; proxy_redirect http://localhost:9001 http://localhost:9000; } Any request for /app goes to :9001, whereas the default site is hosted on :9000. GET requests work fine. But whenever I submit a POST request to /app/any/post/url it results in a 404 error. Hitting the url directly in the browser via GET /app/any/post/url hits the app server as expected. I found online other people with similar problems and added proxy_set_header Host $http_host; but this hasn't resolved my issue. Any insights are appreciated. Thanks. Full config below: server { listen 9000; ## listen for ipv4; this line is default and implied #listen [::]:80 default_server ipv6only=on; ## listen for ipv6 root /home/scott/src/ph-dox/html; # root ../html; TODO: how to do relative paths? index index.html index.htm; # Make site accessible from http://localhost/ server_name localhost; location / { # First attempt to serve request as file, then # as directory, then fall back to displaying a 404. try_files $uri $uri/ /index.html; # Uncomment to enable naxsi on this location # include /etc/nginx/naxsi.rules } location /app/ { # rewrite here sends to app server without the /app qualifier rewrite /app/(.*)$ /$1 break; proxy_set_header Host $http_host; proxy_pass http://localhost:9001; proxy_redirect http://localhost:9001 http://localhost:9000; } location /doc/ { alias /usr/share/doc/; autoindex on; allow 127.0.0.1; allow ::1; deny all; } }

  Read the article

• POST Fail via AJAX Request?

  - by Jascha

  I can't for the life of me figure out why this is happening. This is kind of a repost (submitted to stackoverflow, but maybe a server issue?). I am running a javascript log out function called logOut() that has make a jQuery ajax call to a php script... function logOut(){ var data = new Object; data.log_out = true; $.ajax({ type: 'POST', url: 'http://www.mydomain.com/functions.php', data: data, success: function() { alert('done'); } }); } the php function it calls is here: if(isset($_POST['log_out'])){ $query = "INSERT INTO `token_manager` (`ip_address`) VALUES('logOutSuccess')"; $connection->runQuery($query); // <-- my own database class... // omitted code that clears session etc... die(); } Now, 18 hours out of the day this works, but for some reason, every once in a while, the POST data will not trigger my query. (this will last about an hour or so). I figured out the post data is not being set by adding this at the end of my script... $query = "INSERT INTO `token_manager` (`ip_address`) VALUES('POST FAIL')"; $connection->runQuery($query); So, now I know for certain my log out function is being skipped because in my database is the following data: if it were NOT being skipped, my data would show up like this: I know it is being skipped for two reasons, one the die() at the end of my first function, and two, if it were a success a "logOutSuccess" would be registered in the table. Any thoughts? One friend says it's a janky hosting company (hostgator.com). I personally like them because they are cheap and I'm a fan of cpanel. But, if that's the case??? Thanks in advance. -J

  Read the article

• How to save Word documents as HTML to be viewed in Firefox

  - by private_meta

  I'm in need for saving a Word document as HTML. It has some background images, other images, texts, ... It opens correctly in Internet Explorer, but how can I save a word doc as HTML so that Firefox and other current browsers render it correctly? All images are missing in the document. I looked through the generated html document, but the paths for the images appear to be correct. Any idea? Things like "Don't save docs as html" won't be helpful here. Edit: To make myself clear, the normal "Save as HTML" doesn't cut it, the result is broken in any browser other than Internet Explorer. Edit 2: What I'm using is Word 2010 and Firefox 4. I also tried rendering it in the latest Chrome version, which failed as well. I used different compatibility settings for saving as html, it did not help

  Read the article

• Adding js to a drupal node form

  - by googletorp

  In Drupal you can create your own nodetype in a custom module. Doing this you get to create your own form which is all very nice. However if you want to add js the form things get a bit more tricky. If you add the js in the form, the js will only be added form the form when it is loaded. If the user would post the form with validation errors, the form function is not run again and thus the js is not added. Normally you would just create a menu callback and add the js there, but for the node add form, this wont be a possible solution. So what is the best solution for adding js in a node add form, to keep it persistant when the form doesn't validate?

  Read the article

• wireshark http POST

  - by user39051

  Hi I would like to have a http POST request method CAPTURE filter I know it is easy to do it by display filter http.request.method==POST but I need tcpdump compatible I wrote tcp dst port 80 and (tcp[13] = 0x18) But it is not perfect... tcp dst port 80 and (tcp[((tcp[12:1] & 0xf0) 2):4] = 0x504f5354) works better, but... packages are not treated as a http packages, so I can not do my further display filters... and is there any way to not display frame, tcp, ip and http header information, only data-text-lines field value (content of POST)? or same thing in tcpdump, only dumping of POSTed html form content?

  Read the article

• 7 Web Design Tutorials from PSD to HTML/CSS

  - by Sushaantu

  Some time back when I was looking for some tutorials to create a website from scratch i.e. the process from designing the PSD to slice it and CSS/XHTML it, then not many quality results appeared. But that was like almost an year back and a lot of water has flown down the river Thanes since [...]

  Read the article

• Build tools for php, html, css, js web app development

  - by cs_brandt

  What are some recommendations for a build tool that would allow me to upload changes to a web server or a repository and minify the js and css automatically, and possibly even run Closure compiler on the JavaScript? Im not worried about doing anything with the php code other than update with most recent changes although in the future would like to have phpdoc updated automatically. Just wondering if there is some way to do all this other than an amalgam of scripts that run or have to be invoked every time. Thanks.

  Read the article

• CSS sprite, what html tag to use

  - by yes123

  Hi guys, I am thinking to switch to CSS Sprite for my images. The main problem is I need something compatible with alt attribute. (Seo-purpouse) What Can I use? The first think I thought was to use a standard <img src="1x1.gif" class="mysprite"> The problem is I can't use that because that would like suspicous by google because of this: <img src="1x1.gif" class="mysprite" alt="my keyword1"> <img src="1x1.gif" class="mysprite" alt="my keyword2"> <img src="1x1.gif" class="mysprite" alt="my keyword3"> (the same image "1x1.gif" with different alt text) How we can solve this?

  Read the article

• Customizing post-commit messages in svn for different users

  - by Suresh

  I have an svn repository that users can access (read/write) using their account OR via tunneling over ssh with svnserve. I also have a post-commit hook that sends mails to specific users for different projects via svnnotify: the typical command is svnnotify <params> --to-regex-map <list of email IDs> <regex> For users who have accounts on the system, the notification email is sent from @machine.domain, which is fine. For users coming in via tunnelling, the email gets sent from @machine.domain, which is a fake address since these users don't have an account - the only reason I specify a tunnel-user id is to keep track of who made which update. So my question (finally) is: is there a way to pass a parameter (the "true" email address) to svnserve so that when the post-commit mail is sent, it can be sent "from" the correct email address ? p.s this is my first post here - if I haven't provided sufficient information, apologies: I'm happy to provide more details.

  Read the article

• From .psd to working HTML and CSS - help me suck less

  - by kevinmajor1

  I am not much of a designer. My strength lies in coding. That said, I'm often forced into the role of "The Man," responsible for all aspects of site creation. So, that said I'm wondering if the pros can give me tips/solutions/links to tutorials to my main questions. Resolution. What should I aim for? What are the lower and upper edges I should be aware of? I know that systems like 960 Grid were popular recently. Is that the number I should still aim for? Slicing up a .psd - are there any tricks I should know? I've always found it difficult to get my slices pixel perfect. I'm also really slow at it. I must be looking at it wrong, or missing something fundamental. The same goes for text. Layouts are always filled with the classic "Lorem...", but I can never seem to get real content to fit quite as well on the screen. The advanced (to me, anyway) looking things, like a part of a logo/image overlaying what looks like a content area. How does one do that? How do layouts change/are informed by the decision to go fixed or liquid? Again, any tips/tricks/suggestions/tutorials you can share would be greatly appreciated.

  Read the article

• Practical considerations for HTML / CSS naming conventions (syntax)

  - by Jeroen

  Question: what are the practical considerations for the syntax in class and id values? Note that I'm not asking about the semantics, i.e. the actual words that are being used, as for example described in this blogpost. There are a lot of resources on that side of naming conventions already, in fact obscuring my search for practical information on the various syntactical bits: casing, use of interpunction (specifically the - dash), specific characters to use or avoid, etc. To sum up the reasons I'm asking this question: The naming restrictions on id and class don't naturally lead to any conventions The abundance of resources on the semantic side of naming conventions obscure searches on the syntactic considerations I couldn't find any authorative source on this There wasn't any question on SE Programmers yet on this topic :) Some of the conventions I've considered using: UpperCamelCase, mainly as a cross-over habit from server side coding lowerCamelCase, for consistency with JavaScript naming conventions css-style-classes, which is consistent with naming of css properties (but can be annoying when Ctrl+Shift+ArrowKey selection of text) with_under_scores, which I personally haven't seen used much alllowercase, simple to remember but can be hard to read for longer names UPPERCASEFTW, as a great way to annoy your fellow programmers (perhaps combined with option 4 for readability) And probably I've left out some important options or combinations as well. So: what considerations are there for naming conventions, and to which convention do they lead?

  Read the article

• displaying multi-section html documents - best practices

  - by ecpepper

  I work at a research organization and we publish a lot of large-ish documents, usually organized in sections. What I want to know is how best to present these multi-section documents on our website. Presently, what I do is load the entire document as a single page, with each section as its own div. Then I show and hide divs as needed via a table of contents and "next" and "prev" buttons. The advantages to this are mainly: 1) that you can move between sections very quickly, 2) it produces consistent analytics (when a page is loaded, I know a report is being read). The disadvantages, however, are real: Readers can't take advantage of browser back/forward buttons to move between sections. It's complicated to create direct links to individual sections (I can do it with javascript but it's not easy for other people to grab and share). For long reports, you have to wait for the full report to load before you can move around (and that can include hordes of images and charts). Do other people have thoughts on better ways to organize this? Here's an example of the current system: http://massbudget.org/825

  Read the article

• Layouts in HTML

  - by TerNovi

  I am trying to have a div then inside the division have some different places where I can place stuff. For example. <div blah> <table blah> content... </table> <table blah> content... </table> <table blah> content.... </table> </div> I am not really a web developer so I know this question might seem simple but any help is greatly appreciated. Oh and I am using Macromedia Dreamweaver 8. Thanks.

  Read the article

• HTML coding style: attribute starts on a new line

  - by Matty

  sublvl's front end developer seems to have a strange coding style that I've never seen before. Every time they begin a new element, immediately after the element name they insert a line break. The first thing that appears on the next line is the first attribute of the element. For example: id="player-container"><div id="player-bar"><div id="player-controls-wrapper"><div id="player-controls"><div id ="player-controls-buttons"> <a The above code was found here. I've never seen this kind of coding style before. What's going on here? Is this just a quirky style or is there some reasoning behind it?

  Read the article

• Does sitewide html refactoring affect Google traffic?

  - by Name

  Good morning, I have recently made a big structural change on my site and the very next day the number of Google impressions went from 75.000 to 3.000, with a proportional drop of traffic from searches. No URLs were changed, neither were the page titles or descriptions. Everything is exactly the same, but different looking, except that it does barely appear on Google anymore. Anybody has a clue to why?

  Read the article

• Render Ruby object to interactive html

  - by AvImd

  I am developing a tool that discovers network services enabled on host and writes short summary on them like this: init,1 +-- login,1560 -- +-- bash,1629 +-- nc,12137 -lup 50505 { :net = [ [0] "*:50505 IPv4 UDP " ], :fds = [ [0] "/root (cwd)", [1] "/", [2] "/bin/nc.traditional", [3] "/xochikit/ld_poison.so (stat: No such file or directory)", [4] "/dev/tty2", [5] "*:50505" ] } It proved to be very nice formatted and useful for quick discovery thanks to colors provided by the awesome_print gem. However, its output is just a text. One issue is that if I want to share it, I lose colors. I'd also like to fold and unfold parts of objects, quickly jump to specific processes and what not? Adding comments, for example. Thus I want something web-based. What is the best approach to implement features like these? I haven't worked with web interfaces before and I don't have much experience with Ruby.

  Read the article

• Long wait until POST...

  - by Wesley

  Here are the specs to put things into context: ECS P4VXASD2+ (V5.0) motherboard Intel Pentium 4 Northwood 2.8 GHz (512 KB L2, 533 MHz FSB) 2x 512 MB PC2100 DDR266 RAM 128 MB NVIDIA GeForce FX 5200 AGP WD Caviar SE 80 GB IDE HDD Gigabyte CD-RW drive OKIA 300W ATX PSU So, everytime I try to boot up this computer, it takes at least 10-15 seconds before it will POST. All my other machines will post within 1-2 seconds, but this one takes a particularly long time. I've read suggestions from a Google search to swap the CMOS battery, check BIOS settings, and double check CMOS jumper. Still after follow those, it takes a while to POST. What else could be causing a long delay before POSTing?

  Read the article

• How to use PHP to POST to a web page then get the results back, locally

  - by Patrick Gates

  I have a page on my web server that is PHP that is set to do this if ($_POST['post'] == true) { echo: 'hello, world'; } I want to create a page that calls to that page, posts "post" equal to "true" and then returns the value "hello, world". I have a script that works, but only if the pages are on different servers. Unfortunately, both of these pages are on the same server, so, heres my code, and I'm hoping you guys can help me, Thank you :) function post($site, $post) { $ch = curl_init(); curl_setopt($ch, CURLOPT_URL,$site); curl_setopt($ch, CURLOPT_FAILONERROR,1); curl_setopt ($ch, CURLOPT_POST, 1); curl_setopt ($ch, CURLOPT_POSTFIELDS, $post); curl_setopt($ch, CURLOPT_FOLLOWLOCATION,1); curl_setopt($ch, CURLOPT_RETURNTRANSFER,1); curl_setopt($ch, CURLOPT_TIMEOUT, 15); $retValue = curl_exec($ch); curl_close($ch); return $retValue; } echo post('data.php', 'post=true');

  Read the article

• What is the best way to debug when a jquery post is not firing off an asp.net mvc controller action

  - by oo

  I put a breakpoint on the controller action but it never fires. Is there anyway to catch errors on a jquery post?

  Read the article

• ZF: Form array field - how to display values in the view correctly

  - by Wojciech Fracz

  Let's say I have a Zend_Form form that has a few text fields, e.g: $form = new Zend_Form(); $form->addElement('text', 'name', array( 'required' => true, 'isArray' => true, 'filters' => array( /* ... */ ), 'validators' => array( /* ... */ ), )); $form->addElement('text', 'surname', array( 'required' => true, 'isArray' => true, 'filters' => array( /* ... */ ), 'validators' => array( /* ... */ ), )); After rendering it I have following HTML markup (simplified): <div id="people"> <div class="person"> <input type="text" name="name[]" /> <input type="text" name="surname[]" /> </div> </div> Now I want to have the ability to add as many people as I want. I create a "+" button that in Javascript appends next div.person to the container. Before I submit the form, I have for example 5 names and 5 surnames, posted to the server as arrays. Everything is fine unless somebody puts the value in the field that does not validate. Then the whole form validation fails and when I want to display the form again (with errors) I see the PHP Warning: htmlspecialchars() expects parameter 1 to be string, array given Which is more or less described in ticket: http://framework.zend.com/issues/browse/ZF-8112 However, I came up with a not-very-elegant solution. What I wanted to achieve: have all fields and values rendered again in the view have error messages only next to the fields that contained bad values Here is my solution (view script): <div id="people"> <?php $names = $form->name->getValue(); // will have an array here if the form were submitted $surnames= $form->surname->getValue(); // only if the form were submitted we need to validate fields' values // and display errors next to them; otherwise when user enter the page // and render the form for the first time - he would see Required validator // errors $needsValidation = is_array($names) || is_array($surnames); // print empty fields when the form is displayed the first time if(!is_array($names))$names= array(''); if(!is_array($surnames))$surnames= array(''); // display all fields! foreach($names as $index => $name): $surname = $surnames[$index]; // validate value if needed if($needsValidation){ $form->name->isValid($name); $form->surname->isValid($surname); } ?> <div class="person"> <?=$form->name->setValue($name); // display field with error if did not pass the validation ?> <?=$form->surname->setValue($surname);?> </div> <?php endforeach; ?> </div> The code work, but I want to know if there is an appropriate, more comfortable way to do this? I often hit this problem when there is a need for a more dynamic - multivalue forms and have not find better solution for a long time.

  Read the article

• Does jQuery strip some html elements from a string when using .html()?

  - by Nic Hubbard

  I have a var that contains a full html page, including the head, html, body, etc. When I pass that string into the .html() function, jQuery strips out all those elements, such as body, html, head, etc, which I don't want. My data var contains: <html> <head> <title>Untitled Document</title> </head> <body> </body> </html> // data is a full html document string data = $('<div/>').html(data); // jQuery stips my document string! alert(data.find('head').html()); I am needing to manipulate a full html page string, so that I can return what is in the element. I would like to do this with jQuery, but it seems all of the methods, append(), prepend() and html() all try to convert the string to dom elements, which remove all the other parts of a full html page. Is there another way that I could do this? I would be fine using another method. My final goal is to find certain elements inside my string, so I figured jQuery would be best, since I am so used to it. But, if it is going to trim and remove parts of my string, I am going to have to look for another method. Ideas?

  Read the article

• Zend_Form using subforms getValues() problem

  - by wiseguydigital

  Hi all, I am building a form in Zend Framework 1.9 using subforms as well as Zend_JQuery being enabled on those forms. The form itself is fine and all the error checking etc is working as normal. But the issue I am having is that when I'm trying to retrieve the values in my controller, I'm receiving just the form entry for the last subform e.g. My master form class (abbreviated for speed): Master_Form extends Zend_Form { public function init() { ZendX_JQuery::enableForm($this); $this->setAction('actioninhere') ... ->setAttrib('id', 'mainForm') $sub_one = new Form_One(); $sub_one->setDecorators(... in here I add the jQuery as per the docs); $this->addSubForm($sub_one, 'form-one'); $sub_two = new Form_Two(); $sub_two->setDecorators(... in here I add the jQuery as per the docs); $this->addSubForm($sub_two, 'form-two'); } } So that all works as it should in the display and when I submit without filling in the required values, the correct errors are returned. However, in my controller I have this: class My_Controller extends Zend_Controller_Action { public function createAction() { $request = $this->getRequest(); $form = new Master_Form(); if ($request->isPost()) { if ($form->isValid($request->getPost()) { // This is where I am having the problems print_r($form->getValues()); } } } } When I submit this and it gets past isValid(), the $form-getValues() is only returning the elements from the second subform, not the entire form.

  Read the article

• What's the difference between the input type "text" and "password" in an html form?

  - by Domingo

  Hi everybody, this question might seem stupid, but here's the situation: I'm trying to create an auto login page for my mail using jquery's post request, but it's not working, it works with all other pages except with webmail. So, trying to figure out what was wrong, I recreated the login form, here's the code: <form id="form1" name="form1" method="post" action="https://login.hostmonster.com/"> <label>User <input type="text" name="login" id="user" /> </label> <label>Pass <input name="password" type="password" id="pass" /> </label> <input name="doLogin" type="submit" id="doLogin" value="Login"> </form> The strange thing is when you change the input type of pass to text, the form doesn't work! I can't figure out why. Anyway, if you can tell me what's the real difference between the input type text and password (and not what it says everywhere on the net that the only difference is that when you type stars appear instead of characters) I would appreciate it. Also, do you think this is affecting my jquery's post? Here's the code for it: $j.post('https://login.hostmonster.com/', { login: '[email protected]', password: 'xxx' }, function(data, text){ if (text=='success') { alert('Success '+data); } else { alert('Failed'); } }); Thanks a lot! Regards, D

  Read the article

< Previous Page | 13 14 15 16 17 18 19 20 21 22 23 24  | Next Page >